Haier 001050 Air Conditioner User Manual
Contents
1. EARTHING 4 Plug in A Caution e After brush away dust at the plug insert the plug of the power supply cord into the outlet completely In case of suing exclusive circuit breaker switch on the circuit breaker NO WET HAND 24 Trouble shooting Before asking for service check the following first Phenomenon Cause or check points The system does not restart When unit is stopped it won t restart immediately immediately until 3 minutes have elapsed oe A to protect the system e When the electric plug is pulled out and reinserted the protection circuit will work for 3 minutes to protect the air conditioner During unit operation or at stop a swishing or gurgling noise may be heard At first 2 3 minutes after unit start this noise is more noticeable This noise is generated by refrigerant flowing in the system Normal During unit operation a cracking noise may Performance be heard This noise is generated by the inspection casing expanding or shrinking because of temperature changes Should there be a big noise from air flow in unit operation air filter may be too dirty This is because the system circulates smells Smells are generated from the interior air such as the smell of furniture cigarettes Mist or steam are blown out S l During COOL or DRY operation indoor unit may blow out mist This is due to the sudden cooling of indoo2. 5 Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears Hints After replacing batteries or a power failure happens time setting should be reset Remote controller possesses memory function when use TIMER mode next time just press SET button after mode selecting if time setting is the same as previous one 16 Operation Timer On Off Operation Set clock correctly before starting TIMER operation Remote Controller 1 After unit starts select your desired operation mode Operation mode will be displayed on LCD 2 Timer mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows Remote controller E gt E MBANK iep ieni edd TIMER ON TIMER OFF TIMER ON OFF Then select your desired TIMER mode TIMER ON OFF will flash 3 Time setting Press HOUR AV Y button A Every time the button is pressed time setting increases 1 min if kept depressed it will increase rapidly V Every time the button is pressed time setting decreases 1 min if kept depressed it will decrease rapidly It can be adjusted within 24 hours 4 Timer confirming for TIMER ON After setting correct time press TIMER button to confirm EXE on the remote controller stops flashing fi starts flashing Time displayed Unit starts or stops at x hour x min 5 Time setting for TIMER OFF Just press HOUR button follo
3. Temp setting Unit stop NS In COOL DRY mode 2 In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode 3 In FAN mode It has no SLEEP function 4 Set the wind speed change when sleeping If the wind speed is high or middle before setting for the sleep set for lowing the wind speed after sleeping If it is low wind no change Operation Timer On Off Operation Set clock correctly before starting TIMER operation Remote Controller 1 After unit starts select your desired operation mode Operation mode will be displayed on LCD 2 Timer mode selection Press TIMER button to change TIMER mode Every time the button is pressed display changes as follows Remote controller 0N aa BLANK ego i200 eg TIMERON TIMER OFF TIMER ON OFF Then select your desired TIMER mode TIMER ON or TIMER OFF or id will flash 3 Time setting Press HOUR A V button A Every time the button is pressed time setting increases 1 min if kept depressed it will increase rapidly V Every time the button is pressed time setting decreases 1 min if kept depressed it will decrease rapidly It can be adjusted within 24 hours 4 Confirming your setting After setting correct time press SET button to confirm MH or on the remote controller stops flashing Time displayed Unit starts or stops at x hour x min TIMER ON or TIMER OFF
4. V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller PEOP EOP OPT LOW MED HI AUTO Air conditioner is running under displayed fan speed When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops 10 Operation Dry Operation 4 1 Unit start pe j y e sanuka Press ON OFF on the remote controller unit starts 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN Then Select DRY operation 3 Select temp setting Press TEMP button Every time the button is pressed temp setting increase 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller ots cet_sestllh saat LOW MED HI AUTO Air conditioner is running under displayed fan speed In DRY mode when room temperature becomes lower than temp setting 2 C unit will run intermittently at LOW speed regardless of FAN
5. setting COOL operation starts when room temp is higher than temp setting Temp setting 2 C Temp setting 5 Unit stop i Press ON OFF button the unit stops On reaching temp setting 2 C unit will run in mild DRY mode Operation _ 1 Unit start Remote controller Press ON OFF on the remote controller unit starts 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN Then Select FAN operation 3 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller alal tlll LOW MED HI 4 Unit stop Press ON OFF button the unit stops About FAN operation In FAN operation mode the unit will not operate in COOL mode but only in FAN mode AUTO is not available in FAN mode And temp setting is disabled In FAN mode SLEEP operation is not available Operation Air Flow Direction Adjustment 1 Status display of air sending Vertical flap Horizontal louvers Pos 1 7 Posa Pos 2 Pos 2 Pos 3 NS Pos 3 S Pos 4 y Pos 4 F Pos 5 B Pos 5 Pos 6 S Auto swing Pos 6 FS Pos 7 Pos 8 G 2 Up and down air flow direction For each press of lt gt button air flow direction on remote controller displays as follows according to different operation modes COOL DRY FAN remote somrollen ra Pos 1 Pos 2 Pos
6. the outlet completely STRICT ENFORCEMENT Do not use power supply cord in a bundle PROHIBITION Do not start or stop the operation by disconnecting the power supply cord and so on circuit breaker 0 STRICT ENFORCEMENT Use the proper voltage STRICT ENFORCEMENT Take care not to damage the power supply cord O PROHIBITION Do not channel the air flow directly at people especially at infants or Wy ZINN Use an exclusive power source with a Do not use power supply cord extended or connected in halfway PROHIBITION Do not insert objects into the air inlet or outlet Y E O PROHIBITION Do not try to repair or reconstruct by yourself food art work precise equipment breeding or cultivation E Har PROHIBITION Do not install the unit near a fireplace or other heating apparatus A r PROHIBITION Do not place animals or plants in the direct path of the air flow STRICT Check good condition of the installation stand S PROHIBITION Do not place any objects on or climb on the unit PROHIBITION PROHIBITION Do not pour water onto the unit for cleaning 4b Do not place flower vase or water containers on the top of the unit PROHIBITION Parts and Functions ae Disp
7. 3 Pos 4 gt Pos 6 AUTO remote poser Pos 1 Pos 2 Pos 3 Pos 4 gt Pos 5 gt Pos 6 The vertical flap will swing according to the above positions 3 Left and right air flow direction For each press of gt button remote controller displays as follows remote controller i Pos 1 gt Pos 2 gt Pos 3 gt Pos 4 Pos 5 Pos 6 Pos 7 Pos 8 The horizontal louvers will swing according to the above positions Note When restart after remote turning off the remote controller will automatically memorize the previous set swing position 14 Operation Sleep Operation Before going to bed you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep Use of SLEEP function After the unit starts set the operation status then press SLEEP button before which the clock must be adjusted and time being set Operation Mode 1 In COOL DRY mode 1 hours after SLEEP mode starts temp will become 1 C higher than temp setting After another 1 hours temp rises by 1 C further The unit will run for further 6 hours then stops Temp is higher than temp setting so that room temperature won t be too low for your sleep Remote Controller SOZ MODE HEALTH AIRFLOW SLEEP FRESH SWING QD C lt D 5 Djo RESETCODE LIGHT LO K e e 15 SLEEP operation starts SLEEP operation stops Approx 6hrs
8. SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU 09LH13 HSU 12LH13 e Please read this operation manual before using the air conditioner No 001050 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use please make sure it s inop erative and safe Unplug the air conditioner in order to avoid the risk of child entrapment It must be noticed that air conditioner system contains refrigerants which require speciali zed waste disposal The valuable materials contained in an air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center and contribute to environmental awareness by insisting on an appropriate anti pollution method of disposal Disposal of the packaging of your new air conditioner All the packaging materials employed in the package of your new air conditioner may be disposed without any danger to the environment The cardboard box may be broken or cut into smaller pieces and given to a waste paper disposal service The wrapping bag made of polyethylene and the polyethylene foam pads contain no fluorochloric hydrocarbon All these valuable materials may be taken to a waste coll
9. ecting center and used again after adequate recycling Consult your local authorities for the name and address of the waste materials collecting centers and waste paper disposal services nearest to your house Safety Instructions and Warnings Before starting the air conditioner read the information given in the User s Guide caref ully The User s Guide contains very impor tant observations relating to the assembly operation and maintenance of the air conditioner The manufacturer does not accept respon sibility for any damages that may arise due to non observation of the following instruction e Damaged air conditioners are not to be put into operation In case of doubt consult your supplier e Use of the air conditioner is to be carried out in strict compliance with the relative instructions set forth in the User s Guide e Installation shall be done by professional people don t install unit by yourself e For the purpose of the safety the air con ditioner must be properly grounded in acco rdance with specifications e Always remember to unplug the air conditioner before openning inlet grill Never unplug your air conditioner by pulling on the power cord Always grip plug firmly and pull straight out from the outlet e All electrical repairs must be carried out by qualified electricians Inadequate repairs may result in a major source of danger for the user of the air conditioner e Do not damage any
10. ed Hi Removal of the restriction of emergency or test operation e Press the emergency operation switch once more or manipulate through the remote controller the Pi sound the emergency or test operation is terminated e When the remote controller is manipulated it gets the system back to the normal operation mode 19 Maintenance For Smart Use of The Air Conditioner Setting of proper room Do not block the air inlet temperature or outlet for a long time turn off the power supply main switch 20 Maintenance For Smart Use of The Air Conditioner A WARNING Before maintenance be sure to turn off the system and the circuit breaker Remote Controller Indoor Body Wipe the air conditioner by using a soft and dry cloth For serious stains use a neutral Do not use water wipe the controller with a detergent diluted with water Wring the water dry cloth Do not use glass cleaner or chemical out of the cloth before wiping then wipe off cloth the detergent completely Do not use the following for cleaning Holl Se Hot water over 40 C 104 F may cause discoloring or deformation Gasoline benzine thinner or cleanser may damage the coating of the unit Air Filter cleaning 1 Op
11. en the inlet grille by pulling it upward 2 Remove the filter Push up the filter s center tab slightly until it is released SE PE at from the stopper and remove the filter downward 3 Clean the filter Use a vacuum cleaner to remove dust or wash the filter with water After washing dry the filter completely in the shade 4 Attach the filter Attach the filter correctly so that the FRONT indication is facing to the front Make sure that the filter is completely fixed behind the stopper If the right and left filters are not g attached correctly that may cause defects 5 Close the inlet grille 21 Maintenance Replacement of Air Purifying Filter 1 Open the Inlet Grille Open the inlet grille by pushing each ends of the inlet grille upward use thumbs to push up 2 Detach the standard air filter Slide the knob slightly upward to release the filter then withdraw it 3 Detach old Air Purifying Filter 4 Attach old Air Purifying Filter Put air purifying filter appliances into the right and left filter frames 5 Attach the standard air filter Necessary installation 6 Close the Inlet Grille Close the Grille surely NOTE e The air purifying filter of the bacteria killing medium and the electrostatic air purifying filter accessories with machine will be used based o
12. ervice agent or a similar qualified person 3 If the fuse of indoor unit on PC board is broken please change it with the type of T 3 15A 250V 4 The wiring method should be in line with the local wiring standard 5 After installation the power plug should be easily reached 6 The waste battery should be disposed properly Cautions Safety Instruction e Please read the following Safety Instructions carefully prior to use e The instructions are classified into two levels WARNING and CAUTION according to the seriousness of possible risks and damages as follows Compliance to the instructions are strictly required for safety use Installation A WARNING Please call Sales Service Shop for the Installation Do not attempt to install the air conditioner by yourself because improper works may cause electric shock fire water leakage Installation in a inadequate place may cause accidents Do not install in the following place A CAUTION Connect the earth Do not install in the place where there is any possibility of inflammable gas leakage around the unit S PROHIBITION Do not get the unit exposed to vapor or oil steam S PROHIBITION Check proper installation of the drainage securely ENFORCEMENT Cautions A WARNING When abnormality such as burnt small found immediately stop the operation button and contact sales shop Connect power supply cord to
13. healthy operation 10 ON OFF button Used for unit start and stop 11 TIMER ON display 12 FAN SPEED display a_ aet_pecll_ cottl LOW MED HI AUTO 13 LOCK display 14 SWING UP DOWN display 15 SLEEP display 16 HEALTH display 17 FRESH AIR display 18 Operation mode display Operation mode AUTO COOL DRY FAN Remote controller VW amp 3 Display board oO 19 Singal sending display 20 UV light degerming function display 21 Left right air flow display 22 TEMP display Remote controller to display the TEMP setting 23 TIMER OFF display 24 CLOCK display 25 TEMP button Used to select your desired temperature 26 FAN button Used to select fan speed LOW MED HI AUTO 27 HEALTH AIRFLOW button Used to set the health airflow mode 28 SWING UP DOWN button Used to select up or down air sending direction 29 SWING LEFT RIGHT button Used to select left right air flow 30 FRESH button Use to set fresh air function 31 SET button Used to confirm timer and clock settings 32 STERILIZE button Use to set UV light degerming function 33 LOCK Used to lock buttons and LCD display If pressed the other buttons will be disabled and the lock condition display appears Press it once again lock will be canceled and lock condition display disappears 34 Ambient temp display To display the Ambient temp NOTE 1 The following functions and related displays are not available 1 2 Cooli
14. lay board nue Air filter inside Anion generator inside Inlet grille Vertical flap Use remote controller to adjust up and down air flow Don t adjust it manually Horizontal louver adjust left and right air flow Actual inlet grille may vary from the one shown in the manual according to the product purchased TATS OUTLET 3 CONNECTING PIPING AND ELECTRICAL WIRING INLET DRAIN HOSE Parts and Functions B88 NBB OGOOOOO OOO OO 1 CODE Used to select CODE A or B with a press A or B will be displayed on LCD Please select A without special explanation 2 RESET When the remote controller appears abnormal use a sharp pointed article to press this button to reset the remote controller normal 3 LIGHT button Control the lightening and extinguishing of the indoor LCD display board 4 TIMER button Used to select TIMER ON TIMER OFF TIMER ON OFF 5 CLOCK button Used to set correct time 6 SLEEP button Used to select sleep mode 7 MODE button V 7b AUTO COOL DRY FAN 8 HOUR button Used to set clock and timer setting Se0e 3 000 e 9 HEALTH button Used to set
15. n real situation e The bacteria killing medium air purifying filter is available for a long time and needn t to be changed But it must be noticed to use the vacuum cleaner frequently to adsorb the dusts covering the purifying filter lest the covering dusts effect the function of the bacteria killing medium air purifying filter It is strictly prohibited for the bacteria killing medium air purifying filter to be washed e The green aspect of the bacteria killing medium air purifying filter will face outside the white aspect will face to the machine and the white side of the electrostatic air purifying filter will face outside Maintenance To Keep Your Air conditioner in Good Condition after Season a 1 Operate in cooling mode for 2 3 hours To prevent breeding mold or bad smell be sure to operate at the designated temperature or 30 C cooling mode and High speed fan mode for 2 3 hours 2 Put off the power supply cord 3 Cleaning the body 4 Take out the batteries from the wireless remote controller 23 Maintenance Before Setting in High season 1 Cleaning the standard air filter Operation without filter may cause troubles Be sure to attach both right and left filters prior to the operation Each of them are of different shapes 2 Connecting the earthing cable A Caution e Incomplete earthing may cause an electric shock
16. ng only unit do not have functions and displays related with heating 6 Parts and Functions E Clock Set When unit is started for the first time and after replacing batteries in SESD remote controller clock should be adjusted as follows SS g 1 Press CLOCK button AM or PM flashes DS TIMER STERILIZE 2 PressA or to set correct time Each press will increase or decrease 1 min If the button is kept depressed time will change quickly 3 After time setting is confirmed press SET AM or PM stop flashing aa while clock starts working E Remote controller s operation When in use put the signal transmission head directly to the receiver hole on the indoor unit The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well Don t throw or knock the remoter controller When electronic started type fluorescent lamp or change over type fluorescent lamp or wireless telephone is installed in the room the receiver is apt to be disturbed in receiving the signals so the distance to the indoor unit should be shorter E Loading of the battery Load the batteries as illustrated right 2 R 03 7 batteries Remove the battery cover Slightly press area and push down the cover as illustrated Load the battery i 7 NS Be sure that the loading is in line with the request as illustrated on the bottom of the case P
17. parts of the air conditioner that carry refrigerant by piercing or performating the air conditioner s tubes with sharp or pointed items crushing or twisting any tubes or scraping the coatings off the surfaces If the refrigerant spurts out and gets into eyes it may result in serious eye injuries Cautions e Do not obstruct or cover the ventilation 7 The appliance is not intended for use grille of the air conditoner Do not put fingers by young children or infirm persons or any other things into the inlet outlet and without supervision swing louver 9 8 Young children should be supervised e Do not allow children to play with the air tO ensure that they do not play with conditioner In no case should children be the applience allowed to sit on the outdoor unit 9 Please employ the proper power plug which fit into the power supply cord Specifications 10 The power plug and connecting cable fee must have acquired the local attestation e The refrigerating circuit is leak proof The machine is adaptive in following situation 1 Applicable ambient temperature range Maximum D B W B 32 C 23 C Indoor Minimum D B W B 18 C 14 C Maximum D B W B 43 C 26 C Maximum D B 18 C Maximum D B 27 C Maximum D B 15 C Maximum D B W B 24 C 18 C Minimum D B W B_ 7 C 8 C Cooling Outdoor Indoor Heating Outdoor 2 If the power supply cord is damaged it must be replaced by the manufacturer or its s
18. r air e Is power plug inserted Does not work at all e Is there a power failure e Is fuse blown out Multiple check e Is the air filter dirty Normally it should be cleaned every 15 days Are there any obstacles before inlet and outlet e ls temperature set correctly e Are there some doors or windows left open Is there any direct sunlight through the window during the cooling operation Use curtain e Are there too much heat sources or too many people in the room during cooling operation Poor cooling 25
19. ss MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN Then Select Auto operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increase 1 C if kept depressed it will increase rapidly V Every time the button is pressed temp setting decrease 1 C if kept depressed it will decrease rapidly Select a desired temperature 4 Fan speed selection Press FAN button For each press fan speed changes as follows Remote controller E er wer POTT i LOW MED HI AUTO Air conditioner is running under displayed fan speed When FAN is set to AUTO the air conditioner automatically adjusts the fan speed according to room temperature 5 Unit stop Press ON OFF button the unit stops About Auto Operation Under the mode of auto operation air conditioner will automatically select Cool or Dry operation according to room temperature and setting temperature Operation Cool Operation Ph p a 1 Unit start Remote controller Press ON OFF on the remote controller unit starts 2 Select operation mode Press MODE button For each press operation mode changes as follows Remote controller AUTO COOL DRY FAN Then Select COOL operation 3 Select temp setting Press TEMP button A Every time the button is pressed temp setting increase 1 C if kept depressed it will increase rapidly
20. ut on the cover again Confirmation indicator After pressing power ON OFF if no display reload the batteries Note Full display or unclear display during operation indicates the batteries have been used up Please change batteries Used two new same typed batteries when loading if the remote controller can t run normally during operation please remove the batteries and reload several minutes later Hint Remove the batteries in case unit won t be in usage for a long period If there are any display after taking out just need to press reset key Operation Remote controller MODE HEALTH AIRFLOW SLEEP FRESH SWING 1 Unit start Press ON OFF on the remote controller unit starts 2 Health anion function Press HEALTH button For each press 7 is displayed Air conditioner starts health anion function operation For twice press g disappears the operation stops When indoor fan motor is running it has healthy process function It s available under any mode BRIEF INTRODUCTION TO HEALTH ANION FUCTION The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room Operation Auto Operation coe 1 Unit start Remote controller Press ON OFF on the remote controller unit starts 2 Select operation mode Pre
21. w the same procedure in Time setting for TIMER ON 6 Time confirming for TIMER OFF After time setting press SET button to confirm rea on the remote controller stops blinking Time displayed Unit stops at x hour x min To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears According to the Time setting sequence of TIMER ON or TIMER OFF either Start Stop or Stop Start can be achieved 17 Operation Emergency and Test Operation Emergency operation e Use this operation only when the remote controller is defective or lost e When the emergency operation switch is pressed the Pi sound is heard once which means J the start of this operation e In this operation the system automatically selects the operation modes cooling or heating according to the room temperature e When machine is running in emergency the set value of temperature and wind speed couldn t be altered meanwhile it can t operate for dehumidifying or under timing mode Test operation Test operation switch is the same as emergency switch e Use this switch in the test operation when the room temperature is below 16 C do not use it in the normal operation e Continue to press the test operation switch for more than 5 seconds After you hear the Pi sound twice release your finger from the switch the cooling operation starts with the air flow spe
Download Pdf Manuals
Related Search