Graco 35 Car Seat User Manual
Contents
1. 1 Slide replacement Drum onto hex shaft 5 Turn Drum Adjustment Dial D to maximum height Removal 1 2 Slide drum off of hex shaft A amp lb gt ti14765a 6 3A0101B Operation Starting the Engine 7 Start Engine a Move fuel valve to open 3 Engage Rear Wheel Brake G to prevent Grind Lazer from moving ti5248a 270 390 Models b Move choke to closed D Br 4 480 Models Only Attach LineDriver to GrindLazer S OFF N ON e m ti3315a 270 amp 390 Models 480 Models ti15089a d Pull starter cord 5 Push down on handle bars until drum is locked into UP position e ti5264a 270 390 Models ti14758a f Set throttle to desired setting 6 480 Models Only Make sure Engine Stop Switch eec C is in UP position D gt q n oe ti6483a S pe ti15088a 3A0101B 7 Operation Cutting Material 5 Push down on handle bars pull engagement lever and lower drum into DOWN position 1 Start Engine see page 7 2 Connect Emergency Shut Off Cord C to operator ti14755a 6 Rotate Drum Adjustment Dial D until drum comes into contact with surface and desired depth is reached ti14756a NOTE Several test cuts may be needed to dial in desired cutting depth SS ti6483a NOTE On harder surfaces it may be best to make several passes in increments of 1 32 in to 1 8 in2. e The engine should not labor Run engine at full speed and adjust forward speed to fit the work being performed Harder concrete surfaces will have to be cut at a slower pace than asphalt or other softer sur faces 3A0101B 11 Maintenance Maintenance The following steps should be performed to maintain proper operation and sustain the life of the GrindLazer BEFORE OPERATION e Visually inspect the entire unit for damage or loose connections e Check engine oil see engine manual e Check drum bushings and cutters e Check drum for uneven wear e Check for proper tire pressure DAILY e Insert and clean air filter element e Clean dust and debris from exterior of unit do NOT use pressure washer or other high pressure clean ing equipment e Check engine oil level and fill as necessary e Check and fill gas tank e Remove air filter cover and clean element Replace element if necessary Replacement elements can be purchased from your local engine dealer AFTER THE FIRST 20 HOURS OF OPERATION e Drain engine oil and refill with clean oil See engine manual for correct viscosity EVERY 40 50 HOURS OF OPERATION e Change engine oil See engine manual e Grease wheel bearings 12 Insert grease into the grease fittings on the drum mount and center hinge ti14760a AS REQUIRED Check drive belt and tension and tighten or replace as needed For additional information about engine mainte
3. e Wear a properly fit tested and government approved respirator suitable for the dust conditions EQUIPMENT MISUSE HAZARD Misuse can cause death or serious injury e Do not operate the unit when fatigued or under the influence of drugs or alcohol e Do not leave the work area while equipment is energized Turn off all equipment when equipment is not in use Check equipment daily Repair or replace worn or damaged parts immediately with genuine manu facturer s replacement parts only Do not alter or modify equipment Use equipment only for its intended purpose Call your distributor for information Keep children and animals away from work area Comply with all applicable safety regulations Maintain a safe operating distance from other people in the work area Avoid any pipes columns openings or any other objects protruding from work surface MOVING VEHICLE HAZARD Careless and reckless behavior causes accidents Falling from vehicle running into people or object or being struck by other vehicles may result in serious injury or death e Do not step on forward reverse pedals Make turns slowly Do not make turns greater than 45 Loss of traction may occur going downhill Do not operate on slopes greater than 15 Do not carry passengers Do not tow Use with line striping equipment only Use appropriate traffic control in all traffic areas Refer to Manual on Uniform Traffic Control Devices MUTCD U S Department of Transportation
4. 71 1 37 94 0 Length in cm 62 157 5 73 185 4 Weight lb kg 330 150 430 195 Noise dBa sound Power per ISO 3744 108 6 ound Pressure measured at 92 1 3 1 feet 1m Vibration m sec per ISO 3744 With LineDriver 4 9 ee ee a l Power Rating HorsePower per SAE J1349 6 0 3600 rpm Maximum storage time years 5 Maximum lifetime years 10 Power efficiency factor 200 ground meters per liter fuel 3A0101B 13 Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structu
5. FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s a la suite de ou en rapport directement ou indirectement avec les proc dures concern es Graco Information For the latest information about Graco products visit www graco com TO PLACE AN ORDER contact your Graco distributor or call 1 800 690 2894 to identify the nearest distribu
6. Federal Highway Administration or local highway and transportation regulations MOVING PARTS HAZARD Moving parts can pinch or amputate fingers and other body parts e Keep clear of moving parts e Do not operate equipment with protective guards or covers removed e Before checking moving or servicing equipment disable power supply BURN HAZARD of Equipment surfaces that are heated can become very hot during operation To avoid severe burns do not touch hot equipment Wait until equipment has cooled completely i 2 3A0101B Warnings FIRE AND EXPLOSION HAZARD Flammable fumes such as solvent and paint fumes in work area can ignite or explode To help prevent fire and explosion Use equipment only in well ventilated area Do not fill fuel tank while engine is running or hot shut off engine and let it cool Fuel is flammable and can ignite or explode if spilled on hot surface Keep work area free of debris including solvent rags and gasoline Keep a fire extinguisher in work area CARBON MONOXIDE HAZARD Exhaust contains poisonous carbon monoxide which is colorless and odorless Breathing carbon monoxide can cause death Do not operate in an enclosed area PERSONAL PROTECTIVE EQUIPMENT You must wear appropriate protective equipment when operating servicing or when in the operating area of the equipment to help protect you from serious injury including eye injury inhalation of dust or chemicals burns and hea
7. NOTE Drum clutch will not engage when engine is running at idle 480 Models LineDriver must be attached to GrindLazer 8 3A0101B Depth Control Wheels Using Depth Control Wheels as a 5 in or 10 in Wide Cutting Guide To make a 5 in cut install two spacers S on outside of Depth Control Wheels K el o 5 in __ To make a 10 in cut install two spacers S on of Depth Control Wheels K ti15094a 0n 3A0101B lp ISIE ti15095a inside Operation How to Level the Drum To properly level the drum GrindLazer must be resting on a flat level surface 1 Make sure drum is properly installed see Drum Replacement page 6 2 Push down on handle bars pull engagement lever and lower drum into DOWN position 3 Loosen but do not remove three bolts T on Depth Control Wheel plate 4 Adjust plate until guide wheels lay flat on surface 5 Tighten three bolts T on plate Operation Stop Cutting Material 3 Turn Engine Power Switch B OFF ti15176a a N ti15177a 1 Push down on handle bars until drum is locked into Q UP position ve S E E F AO 270 amp 390 Models 480 Models Clean Up Clean the entire exterior of the machine after it has cooled at the end of each work day Check for worn or damaged parts and perform any required Maintenance page 12 ti14758a 2 Slide Engine Throttl
8. Operation G g TM GrindLazer 3A0101B Patents Pending ENG Designed to grind flat horizontal concrete or asphalt surfaces For removal of materials from concrete and asphalt surfaces For professional outdoor use only Model 571002 Forward cut GrindLazer 270 270 cc 9 hp Model 571003 Forward cut GrindLazer 390 390 cc 13 hp Model 571004 Reverse up cut Must be used with LineDriver GrindLazer 480 480 cc 16 hp IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions in this manual Save these instructions GrindLazer 480 Related Manuals a Repair 3A0102 Drums cutters and LineDriver sold separately Parts 3A0103 ce C HOO3 PROVEN QUALITY LEADING TECHNOLOGY Warnings Warnings The following warnings are for the setup use grounding maintenance and repair of this equipment The exclamation point symbol alerts you to a general warning and the hazard symbol refers to procedure specific risk Refer back to these warnings Additional product specific warnings may be found throughout the body of this manual where applicable DUST AND DEBRIS HAZARD Use of this equipment to grind concrete and other paving materials can result in the release of potentially harmful dust or chemicals from the materials e For use only by sophisticated users familiar with applicable governmental safety and industrial hygiene regulations e Use equipment only in a well ventilated area
9. e Lever A to low setting e ecoce gt ti6482a 10 3A0101B Cutting Drum Assemblies Cutting Drum Assemblies NOTE Each increment on Drum Adjustment Dial D is a Pt fy de 0 010 in 0 25 mm depth change of cutting drum NW 4 eum Avoid touching or handling drum after use until it has completely cooled Different drum configurations can be used for different applications There are three different types of drum assemblies compatible with the GrindLazer carbide flails carbide millers and diamond blades Carbide Flail Cutter Assembly Gradually adjust depth down to remove marking line minimal amount of paved surface should be removed Carbide Miller Cutter Assembly Best results for deep cuts are achieved by making sev eral thin passes A single pass should be no deeper than 1 32 in or damage to rods and cutters could occur Diamond Blade Assembly 480 Models Only Watch Depth Control Wheels K during operation if wheels are spinning proper depth is being achieved Handle Bar Adjustment To adjust handle bar remove four screws S slide handle bar to desired height and replace screws and NOTICE tighten Diamond Blades are designed to be cooled by air flow around the blades Lift blade out of cut every 10 to 15 seconds then run at full speed for several seconds to prevent excessive heat build up which could damage the blades Cutter and Drum Assemblies AP
10. nance see Honda 270 and 390 models or Briggs and Stratton 480 models engine manual Caster Wheel Maintenance EVERY MONTH Grease wheel bearing Check pin for wear If pin is worn out there will be play in caster wheel Reverse or replace pin as needed Check caster wheel alignment as necessary To align loosen set screw align wheel and tighten screw Front Swivel Tire Alignment 1 2 Loosen cap screw Rotate front wheel fork left or right as necessary to straighten alignment Tighten cap screw Push GrindLazer and let it roll with hands off of GrindLazer NOTE If GrindLazer rolls right or left repeat steps 1 and 3 until GrindLazer rolls straight 3A0101B Technical Data Technical Data rindLazer 2 0 Model 5 100 f Unpackaged Packaged Height in cm 46 116 8 50 5 128 3 Width in cm 28 71 1 37 94 0 Weight Ib kg 300 136 400 181 Noise dBa Sound Pressure measured at 916 3 1 feet 1m Vibration m sec per ISO 3744 Without ineDriver With LineDriver 8 3 Power Rating HorsePower per SAE J1349 8 0 3600 rpm rindLazer 390 Model 5 100 f Unpackaged Packaged Height in cm 46 116 8 50 5 128 3 Width in cm 28 71 1 37 94 0 Length in cm 62 157 5 73 185 4 Weight Ib kg 310 141 410 186 Noise dBa Sound Pressure measured at 3 1 feet 1m 11 0 3600 rpm rindLazer 480 Model 571004 Height in cm 46 116 8 50 5 128 3 Width in cm 28
11. res accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
12. ring loss This equipment includes but is not limited to e Protective eye wear Protective shoes Gloves Hearing protection Properly fit tested and government approved respirator suitable for the dust conditions 3A0101B 3 Component Identification Component Identification 270 and 390 Models Engine Throttle Lever Adjusts engine speed Engine Stop Switch Supplies power to Engine Emergency Shut Off Clamps onto the operator and shuts engine off if cord is disconnected during operation Drum Adjustment Dial Sets depth of drum cut Drum Engage Lever When lever is engaged handle bars can be pushed down to raise the cutting drum off of surface and locked into UP position Once drum is locked in UP position GrindLazer can be moved around without drum touching surface is engaged front wheel becomes unlocked and is allowed to turn freely M Vacuum Port Porto attach vacuum to reduce dust and debris during operation 4 3A0101B Operation The GrindLazer is designed to plane flat horizontal con crete or asphalt slabs GrindLazer 270 270 cc and GrindLazer 390 390 cc models are designed to be operated by a single opera tor positioned at the back of the unit or in conjunction with LineDriver GrindLazer 480 480 cc can ONLY be operated with LineDriver Maintain a safe operating distance from other people in the work area Avoid any pipes columns openings or any other objects protruding from work
13. surface 3A0101B Operation Start Up Before starting engine perform the following e Read and understand engine manual e Make sure all guards are in place and secure e Make sure all mechanical fasteners are secure e Inspect for damage to engine and other exterior surfaces e Use correct cutters for each job Make sure drum is balanced and the correct number size and type of cutter wheels are being used Make sure drum shaft is locked and secured e Inspect work area to locate any pipes columns deck inserts or other objects protruding from work surface Avoid these objects during operation Operation Drum Installation Replacement Installation 3 Lower Drum Adjustment Dial D and pull Drum Engage Lever E so drum rests on ground NOTE Carbide Flail Cutter drums do not require specific orientation or direction Carbide Millers and Diamond Blades are directional They should be stacked so that the arrows on the Millers and Blades face the same direction as the rotation of the drum ti14755a isina Carbide Miller Diamond e RA 270 and 390 models are designed for forward cut grinding the drum rotates in the same direction that it travels 480 models are design for reverse up cut grinding the drum rotates in the opposite direction that it travels ti15256a LOD ti15137a ti15138a DS S N R2 RRAN Forward Cut 270 390 Models Reverse up cut 480 Models
14. tor All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Original instructions This manual contains English MM 3A0101 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 Copyright 2009 Graco Inc is registered to ISO 9001 www graco com Revised 06 2011
Download Pdf Manuals
Related Search