Genie 2060 Garage Door Opener User Manual
Contents
1. 9 Mounting door bracket 21 Center of bracket must be on centerline of door and must be mounted as high as possible Fig 2 12A amp B Hold bracket against door at preferred location and mark screw holes for wooden doors drill 5 32 inch pilot holes a Fasten door bracket using 3 lag screws 22 b Check thickness of door against lag screws It may be necessary to mount door bracket on a 2 x 6 etc attached to inside of door to prevent screws from coming out other side of garage door Fig 2 12A for light weight doors CAUTION In the case of sectional doors the door bracket must not be below the highest set of rollers Fig 2 13 there are a wide variety of reinforcements depending on manufacturer and some are equipped with hardware that is intended to be used in place of the door bracket Be sure to confirm proper use of this hardware with your door manufacturer Unauthorized improper use of these attachment systems could void your warranty WHEREVER POSSIBLE USE DOOR BRACKET SUPPLIED WITH YOUR GENIE OPERATOR a Fasten door bracket using 3 self drilling screws 47 1 4 x 2 Lag screw FOR HELP 1 800 354 3643 OR GENIECOMPANY COM WOODEN ONE PIECE top of door 1 4 20 Self drilling screw 47 INSTALLATION OPEN YELLOW PARTS BAG 10 Attach door arms 23 and 26 For sectional doors Connect short leg of curved arm to door bracket2. or Deat trained service person using proper tools and instructions SPRING TENSION FILL THIS IN AT TIME OF INSTALLATION FOR YOUR OWN RECORDS SO THAT IT WILL BE AVAILABLE IF YOU EVER NEED TO CALL US Date Purchased Serial Number Operator Model Dealer Name Dealer Address City State Zip See Fig 1 1 IMPORTANT INSTALLATION INSTRUCTIONS A WARNING To reduce the risk of severe injury or death READ AND FOLLOW ALL SAFETY INSTALLATION AND OPERATION INSTRUCTIONS If you have any questions or do not understand an instruction call your service representative Do Not install Opener on an improperly balanced door An improperly balanced door may cause severe injury Repairs and adjustments to cables spring assemblies and other hardware must be made by a trained service person using proper tools and instructions 3 Remove all handles and ropes and disable all locks connected to the door before installing the Opener 4 Install door Opener 7 or more above the floor Mount the emergency release knob 6 above the floor Do Not connect the Opener to the power source until instructed to do so Locate the Wall Control Within sight of the garage door e Ata minimum height of 5 so small children cannot reach it e Away from all moving parts of the garage door Install the entrapment WARNING label next to the wall button or console Install the emergency release tag on the emerg
3. run wire down inside groove in top of rail back to power head Use wire clip 44 to help maintain slack Fig 1 20 close brown wire OPEN limit switch 15A switch NDA Place OPEN limit switch over top of rail about 12 inches from power head Fig 1 21 A n Check that white lever is side away from a DD power head This means limit switches 0M sew e hang off opposite sides of rail Check this to help verify they are installed properly Insert set screw 16 into limit switch hand tight only to temporarily hold switch in place Attach grey wire to switch Fig 1 21 Leaving some slack in wire Fig 1 21 run wire down inside groove in top of rail back to power head Use wire clip 44 to help maintain slack Fig 1 21 e Coil excess wire and tape it to top of power head Fig 1 21A wii 16 ES 44 38 32 x 3 8 Hex head screw Wire clip SECT 2 INSTALLATION FOR HELP 1 800 354 3643 OR GENIECOMPANY COM NOTE There are differences in installations depending on which type of door you have These differences are explained throughout this section Please note those steps which are applicable to your particular door REFER TO PAGES 2 amp 3 There are two basic types of residential garage doors They are SECTIONAL DOORS divided into a set of narrow panels usually four connected by hinges so door can bend as it ri
4. ORANGE SECONDARY SECUNDARIO SECOMDAIRE u CLOSE BLACK NEGRO NOIR BLUE AZUL BLEU BROWN MARRON BRUN GREEN VERDE VERT GREY GRIS GRIS ORANGE NARANJA ORANGE PURPLE MORADO POURPPRE RED ROJO ROUGE RED WHITE ROJO BLANCO ROUGE BLANC STRIPED RAYAS RAYE YELLOW AMARILLO JAUNE THERMAL PROTECTOR PROTECTOR TERMICO PROTECTEUR THERMIQUE MOTOR MOTOR MOTEUR RPM SENSOR DETECTOR DE FREQUENCIA DE ROTACION DETECTEUR DU R MIN WALL CONTROL CONTROL DE PARED COMMANDE DE MURAL SISTEMA DE STB SYSTEME DU STB l l l PURPLE Vec ORANGE m 4 MOTOR 5 CONDENSADOR 5 CONDENSATEUR DU MOTEUR I LL 7 ORANGE SIGNAL HOUSING GREEN RADIO CONNECTOR SEMI TRIP CONEXION DE RADIO 9 CONNECTEUR RADIO BOTTIER DE SEQUENCEUR i 40 1 l l le aee 000 es a l 12 BRA XE TIT STB SYSTEM SISTEMA DE STB 13 SYSTEME DU STB T E COMMAND MANDAR COMMANDE 2 STRIPED 4 l i 45 GREY A 3 STRIPED OPEN z STB SYSTEM LLI 1 ABRIR LU BROWN TERMINAL STRIP RERMINALES BORNES CERRAR FERMER The Genie Company Professional Access Systems LIMITED WARRANTY What is covered Any defect in material and workmanship fro
5. Wall Console some models Works like a lighted wall button but includes a Vacation Lock Switch that disables all controls LED indicator shows whether system is powered locked or unlocked Makes console easy to find in dark Controls door opener from inside garage Independent light control allows convenient manual control of the Automatic Lighting System DO NOT use with lighted wall button NOTE All items may not be supplied with your garage door operator 1 PIECE RAIL HARDWARE EXPLODED VIEW FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 2 1 Piece Rail amp Screw Assembly NOTE The operator will not function properly unless the Safe T Beam sensors are installed and the force controls adjusted PARTS LIST PARTS LIST 3 Piece 3 Piece 1 Power Head Assembly See page 5 1 158 1 2 Rail Assembly 1 piece 16 2 3 Rail Assembly 3 piece __ 1 17 1 3A First Rail Section __ 1 18 1 3B Middle Rail Section __ 1 19 1 3C End Rail Section 1 20 4 2 21 1 5 2 22 1 4 x 2 Lag Screw 0 8 8 6 1 23 1 7 RailClamps 1 1 24 2 8 5 16 Hex Shoulder Bolt 8 25 2 9 13 26 10 27 2 11 Collar 28 2 12 Retaining Clip Y Y 2 29 ft 95ft 13 30 830 30 15A Open Limit Switch Assembly Grey 1 1 31 Wall Button varies 3 PIECE RAIL HARDWARE EXPLODED VIEW FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 13 3 Piece Rail amp Screw As
6. 6 2 SECT 7 SETTINGS FORCE 8 LIMITS FOR HELP 1 800 354 3643 OR GENIECOMPANY COM A CAUTION Door opens rapidly e Keep clear of door and its path e Keep ladder to side of power head to prevent being hit by moving parts Be sure and set force adjustments at minimum required to operate door 1 Set limit switch position Check door fully closed If not close door manually Check carriage is between limit switches f not move CLOSE limit switch brown wire to new position between door and carriage Slide CLOSE limit switch back toward carriage until lever is fully lifted Fig 7 1 lighten limit switch set screw e Manually open door to fully open position Check carriage is between limit switches f not move OPEN limit switch to new position between power head and carriage Slide OPEN limit switch back toward carriage until lever is fully lifted Fig 7 1 lighten limit switch set screw 2 Adjust opening force e Engage Carriage by pulling Emergency gi Release Lever toward Powerhead until Fi fi ig 7 2 Lever snaps into engaged position On front panel of power head find adjusting screw marked CLOSE Fig 7 2 NOTE Turn screw gently counterclockwise until it stops 9 y n P When the garage door is closing and NOTE Little force required to move adjusting screws contacts a vehicle or other obstruction the Run operator using w
7. Fig 2 14 Use clevis pin 24 and cotter pin 25 Fig 2 14 Connect straight arm to carriage Use clevis pin 24 and cotter pin 25 Overall length of arms together should be as short as possible but must not be so short that they are vertical when the door is fully closed Fig 2 14 a Move carriage as necessary to adjust length b Place bolts 27 and nuts 28 as far apart as possible Fig 2 14 c lighten bolts and nuts For 1 piece doors Connect short leg of curved arm to carriage Fig 2 14 Use clevis pin 24 and cotter pin 25 Fig 2 14 Connect straight arm to door bracket Use clevis pin 24 and cotter pin 25 Overall length of arms together should be as long as possible Fig 2 14 a Move carriage as necessary to adjust length b Place bolts 27 and nuts 28 as close together as possible Fig 2 14 c lighten bolts and nuts 11 Adjust emergency release knob height Knob should hang approximately 6 feet from the floor adjust as necessary to clear vehicles yet maintain height where it can be easily reached Pull cord through lever until knob is at desired height Tie a new knot at the lever Cut off excess cord Clevis pin CA 25 Cotter pin FOR HELP 1 800 354 3643 OR GENIECOMPANY COM SECTIONAL DOOR some angle off vertical clevis amp cotter pin bolts nuts far apart as possible 1 PIECE DOOR clevis amp cotter pin e bolts nuts close as possi
8. Operator works from wall control but not from remote control Noisy operation STB System malfunction Lights will not go out SOLUTIONS Check lock switch on wall console See section 4 Check the power source e Plug a lamp into outlet used for power head If lamp works power source is OK If not check fuse or circuit breaker f power is OK Check connections at power head terminals Check connections at wall control Motor protector may be open Wait about 20 minutes for protector to reset Check staples on wire from power head to wall control If they cut into insulation they can short wires If wire is cut replace it Was a remote control lost or stolen Erase all remote control codes from receiver memory and reprogram Wall control button sticking Check operation of buttons Check CLOSE limit switch setting See Section 7 Check for shorted wires Check force adjustment See Section 7 Check CONTACT REVERSE See Section 7 Check for light beam obstruction or misalignment of Safe T Beam See Section 3 Check STB self diagnostic code Check OPEN limit switch for short and proper wiring Check force adjustment See section 7 Check for broken door spring Check Safe T Beame System See section 3 Check CLOSE limit switch for short and proper wiring Check force adjustment See Section 7 Relocate remote control inside car Point remote control at door Replace battery Do Not attempt t
9. PF r A mn j f h d N E 4 J gn E e a 9 5 E j r L r 4 1 A mM M D MM M Y Val Va A s NIMM 4 a 9 2 d 1 1 i u h i L _ n jil a r b L ie NM uU d 2 z 2 A 2 A A P Y 2 2 3511035556 GENIE SCREW DRIVE GARAGE Series IS ISL IC H Includes INTELLICODE Remote Control and SERIES II Electronics Included Wall Control MUST be installed prior to operation of this Garage Door Operator 1 Safety Reverse System Must be installed to close door NOTE Your Residential Operator comes with a Rail Assembly which is standard for up to a foot 6 inch high door An extension kit for an 8 foot high door is available For Answers and Assistance 1 800 354 3643 or visit www geniecompany com SAVE THIS MANUAL FOR FUTURE REFERENCE P R E N S TA L LA TI ON CH E CK L l S T FOR HELP 1 800 354 3643 OR GENIECOMPANY COM Things to consider if you are planning to do it yourself Whether you are replacing an existing garage door operator or installing an operator in your garage for the first time there are some pre installation issues which need to be addressed They are as follows The Genie Company recommends that you read and fully understand all information and instructions contained herein before choosing a do it yourself installation Any
10. a Para obtener servicio de garant a para su producto Genie usted debe proporcionar prueba de la fecha y lugar de la compra del producto 1 Servicio de bricolaje Llamar sin cargo a la conexi n del consumidor de Genie marcando el 1 800 354 3643 Representantes entrenados de Genie le asistir n en diagnosticar el problema y har n arreglos para sum inistrarle las piezas necesarias para las reparaciones de bricolaje 0 sea que usted mismo haga Los representantes de servicio entrenados est n disponibles de lunes a viernes de 8 00 a m a 11 00 p m y los s bados de 11 00 a m a 8 00 p m hora del Este sujeto a feriados 2 Servicio de distribuidores autorizados Usted puede obtener el nombre del distribuidor autorizado de Genie llamando a la conexi n del consumidor de Genie marcando el 1 800 654 3643 Si un distribuidor autorizado extiende una garant a de servicio Genie no le reembolsar a usted ni ser responsable por esos cargos Su elecci n de cualesquiera de las opciones de los servicios descritos arriba es el recurso que tiene bajo esta garant a Qu Esta Garant a no Cubre Esta garant a no cubre bater as que considera las partes reemplazables la instalaci n el uso de la propaganda los defectos resultando de accidentes el dafio mientras en tr nsito a nuestra ubicaci n del servicio o resultar de dafio de modificaciones el maltrato o el abuso la falta de la conservaci n apropiada la reparaci n o las modific
11. object or a 2 x 4 board laid flat at the center of the doorway on the floor After adjusting either the Force or the Limit of travel retest the Door Opener Failure to adjust the Opener properly may cause severe injury or death When possible use the Emergency Release only when the door is closed Use caution when using this Release with the door open Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of severe injury or death KEEP GARAGE DOORS PROPERLY BALANCED See Owner s Manual An improperly balanced door increases the risk of severe injury or death Have a Genie Factory Authorized Dealer make repairs to cables spring assemblies and other hardware SAVE THESE INSTRUCTIONS SECT 10 MAINTENANCE amp TROUBLESHOOTING MONTHLY MAINTENANCE MAINTENANCE CHECK OFF Door springs and hardware e Oil door rollers bearings and hinges Use silicone lubricant or light oil NOTE Do not operate door automatically or manually if springs are broken CONTACT A PROFESSIONAL FOR SERVICE Balance door Close door e Release carriage from rail assembly Pull emergency release knob down Raise door manually about 3 feet Door should stay in that position NOTE If door moves HAVE DOOR SERVICED BY A PROFESSIONAL e Reattach carriage to rail assembly Pull emergency release knob toward power head e Close door Contact reverse Lay 2 x 4 board flat
12. garantiza mientras usted sea el propietario de SU Casa Qui n obtiene la garant a La garant a est limitada al consumidor que compr originalmente el producto Alcance geogr fico Esta garant a se aplica s lo a los productos Genie comprados en los Estados Unidos y Canada Lo que haremos Si su producto Genie es defectuoso mandaremos el reemplazo los partes o a opci n nuestra lo reemplazaremos sin cargo alguno para usted Si mandamos el reemplazo las partes su producto Genie podemos usar piezas de reemplazo nuevas o reacondicionadas Si optamos por cambiar su producto Genie podemos cambiarlo por uno nuevo o reacondicionado del mismo dise o o similar Limitaciones LAS GARANT AS IMPL CITAS INCLUYENDO AQUELLAS DE CONVENIENCIA PARA UN PROPOSITO PARTICULAR Y COMERCIABILIDAD UNA GARANTIA NO ESCRITA QUE EL PRODUCTO ES APROPIADO PARA USO ORDINARIO ESTAN LIMITADAS A UN ANO A PARTIR DE LA FECHA DE COMPRA GENIE NO PAGARA POR PERDIDA DEL USO DE SU PRODUCTO GENIE O POR DANOS DE PROPIEDAD CAUSADOS POR SU PRODUCTO GENIE O POR LA FALLA DE TRABAJAR POR DANOS CUALESQUIERA ESPECIALES INCIDENTALES O EMERGENTES POR DANOS RESULTANTES DEL MAL USO 0 LA MODIFICACI N DE SU PRODUCTO GENIE Algunos estados y provincias no permiten limitaciones del tiempo que dura la garant a implicita o la exclusi n de dafios incidentales o circunstanciales entonces puede que las limitaciones de arriba no se apliquen C mo obtener servicio de garant
13. head and wall control Connect wires to power head White wire to terminal 1 Striped wire to terminal 2 Tighten screws Connect wires to wall control Striped wire to terminal B White wire to terminal W Tighten screws 4 Mount wall control Fig 4 4 For Wall Console or Wall Button Use pan head screws 34 5 Mount entrapment warning label Fig 4 4 e Remove protective backing e Stick label to wall next to wall control Tacks or staples may be required on some rough texture surfaces NOTE Additional wall controls are available from your dealer ONLY ONE OF YOUR WALL CONTROLS MAY BE THE LIGHTED TYPE If you have a lighted wall control all your additional controls must be un lighted More than one lighted wall control per operator will cause a malfunction Ttt 34 6 x 1 1 4 Pan head screw WALL CONTROL OPERATIONAL FEATURES FOR HELP GENIECOMPANY COM 1 Wall console Fig 4 5 A Vacation locking switch Lock disable all controls after door closes Unlock allows all controls to work normally NOTE Carriage must stay in contact with CLOSE limit switch in order for the vacation locking switch to work B Door control button Opens and closes door from inside garage Lights on shows system has power available and vacation switch is not locked Lights out shows either power is not available or vacation locking switch is locked C Independent li
14. les dispositions n cessaires pour vous fournir les pi ces requises afin que vous puissiez effectuer les r parations par vous m me Vous pouvez joindre ce service du lundi au vendredi de 8 h 23 h et le samedi de 11 h 20 h heure de l Est sauf jours f ri s 2 Service effectu par des techniciens agr s Appeler le service la client le Genie au 1 800 654 3643 qui vous communiquera le nom d un technicien agr Si le technicien agr offre un service de garantie les frais encourus ne seront pas rembours s par Genie et Genie ne sera pas tenu responsable du r glement des frais Le choix de l une des options de service d crite ci dessus est le recours dont vous disposez sous cette garantie Que Cette Garantie Pas Couverture Cette garantie pas piles couverture qui sont ils consid r des parties remplacables installation usage 7 d fauts Rayon r sulter de accidents dommages dans travers e notre emplacement service ou pas dommages qui r sulte de changements ou abus manque d entretien propre r paration ou modifications inautoris e du produit apposant d attachement ont fourni avec le produit programmant de H de T de Rayon Sir ajustement nettoyage Fils pinc s ou cass s l Attelage a d clench les ajustements de Contr le de Force la porte d quilibre les ressort ou les c bles cass s les coupures de courant l usage de rallonges manquant ou a endommag des parties sur escompt clearanc
15. on the floor in the center of garage doorway See page 28 Close door using wall button or remote control NOTE If door fails to reverse on contact with board See page 28 CONTACT REVERSE If operator still fails replace operator or HAVE THE OPERATOR SERVICED BY A PROFESSIONAL YEARLY MAINTENANCE Drive Screw e Lubricate drive screw Use GENIE GLUS lubricant A CAUTION Use only GENIE GLUS lubricant because other lubricants may damage operator TR O U B L E SH OOTI N G FOR HELP 1 800 354 3643 OR GENIECOMPANY COM STB SELF DIAGNOSTIC TROUBLESHOOTING PPP PPP PPP eee EPP PPP PPP PPP dd ddddddddddddddddddd Wddddddddgdddddddddi IO PPP PPP PP PEP PPP PPP PPP PPP PPP Pe PAPER PAAR PPEPPPPPPPPPPPPP PEPER PPPPPPPPPPPPPPPPPPPP PPPPPPPPPPPPPPPP PPP Just mark the appropriate box each time you perform routine maintenance One less thing you will have to try and remember on your busy schedule is whether or not you did the maintenance last month NONE REQUIRED SOURCE RED LED SENSOR GREEN LED INDICATED CONDITION REQUIRED ACTION 7E 1 POWER HEAD NOT POWERED 1 CHECK BREAKERS FUSES PLUGS 2 WIRING FROM POWER HEAD BAD 2 CHECK WIRING FOR OBVIOUS SHORTS 1 WIRING TO SOURCE MISSING OR BAD 1 CHECK WIRING 2 POWER HAS BEEN INTERRUPTED 2 REMOVE POWER AND REAPPLY 1 BEAM NOT ALIGNED 2 BEAM OBSTRUCTED 2 BLINKS PAUSE REPEAT eo 33 3 SENSOR DEFECTIVE 3 CALL CUSTOMER SE
16. questions should be directed to the Genie Company or an authorized Genie Dealer The issue numbers below refer to the circled numbers in the illustrations on page 3 Check your ceiling where the power You need a 110 120 Volt power supply head of your new unit will be mounted available The outlet should be no more than Plan how you will be mounting the power head 3 feet from the power head once it is mounted The It is possible that ceiling joists may be in the is 4 ft in length SEE WARNING BELOW exact position needed with respect to the garage door operator It may be necessary to add an additional bracket and fasteners not included with your new door operator kit To avoid damage to your door and or operator make sure you disable any door locks prior to installing your operator Check the wall directly above the garage door The door operators header bracket must be securely fastened to this wall Ensure that the structure will provide a strong mounting location Ensure that your door is properly balanced and moving freely SEE WARNING BELOW 9 8 NOT SHOWN If your garage does not have 3 Check to see if the mounting location 8 a separate entry door you should consider for the Safe T Beam System STB is an emergency release kit GER 2 for installation clear from obstruction and has a nd on your garage door See page C at the center of surface available for attaching the STB brack thi
17. se glisse dans la poche de veston ou le sac main Wireless Keypad Entry System Operates Intellicode Garage Door Operators without Remote Control or key N Sistema de entrada por teclado num rico inal mbrico Acciona los abridores de puertas de garaje Intellicode sin control remoto o llave 49 95 Syst me d ouvre porte de garage clavier sans fil Actionne les ouvre porte de garage avec Intellicode sans t l commande ni cl NO 3 1 4 oz tubes Screw Grease Ensures proper equipment wear protection 3 1 4 once lubricante de tornillo accionar Asegura componente correcto protecci n por deterioro 1 95 La onza 1 4 lubricant de la vis 3 Garantir componant exact par syst me d fense vers user Universal Wall Button Provides additional convenient inside operation of Door Bot n de pared universal Proporciona operaci n conveniente de la puerta desde el interior 4 95 Bouton mural universel Actionne l ouvre porte de l int rieur du garage i Perfect Stop Ensures perfect parking Stop Perfecto Asegura el estacionamiento perfecto 4 95 Butoir Perfect Stop Permet de stationner la perfection dans le garage Screw Drive Extension Kit Eighteen inch Extension to increase travel of Screw Drive Operator to accommodate eight foot door Juego de extension deslizante de Screw Drive Una extensi n de 18 pulgadas para aumentar la carrera de un abridor deslizable de tornillo P para acomodar una puert
18. 9 1 To erase all receiver memory such as following loss of remote home sale or tenant turn over e Press and hold learn code button for 10 seconds or until learn code indicator goes out memory Is erased Program remotes as before FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiver antenna Increase the separation between the operator and receiver Connect the operator into an outlet on a circuit different from that to which the appliance is connected Consult the dealer TRANSMITTER COMPLIANCE STATEMENT IMPORTANT SAFETY INSTRUCTIONS Transmitters comply wi
19. KET BRACKET MOUNTING BOARD BRACES 36 POWER CORD TO 120V GROUNDED MN OUTLET 2 EXTENSION SPRING OR TORSION SPRING TYPICAL 1 PIECE DOOR INSTALLATION E OF CONTENTS C1 an CC Id Carpenter s level Go MO E INSTA ONCHECKLIST o n Adjustable wrench Step ladder Pencil Se Wire strippers 5 32 Drill Bit ooo Ez 20 C CH ar RRRERERBERRRERBRIL Phillips screwdriver 6 Ratchet m Q SN Tape measure E i ll 7 16 and 9 16 Sockets Safe T Beam STB Non Contact Reversing System Places an invisible beam across door opening that reverses the door during down travel to the fully open position if anything passes through beam Safe T Reverse Contact Reversing System Automatically stops and reverses a closing door within 2 seconds of contact with an object Safe T Stop Timed Reversed System Automatically opens a closing door if door does not close within 30 seconds Force Guard Control Used to set the force required for opening and closing door For maximum safety set the minimum force required to fully open and close door Automatic Lighting System Two light bulbs up to 60 Watts max each are used for safer entries and exits The light turns on when door is activated and automatically turns off 4 5 minutes later M
20. RVICE 1 CHECK ALIGNMENT 2 CHECK FOR OBSTRUCTION 1 WIRE TO SENSOR MISSING OR BAD 1 CHECK WIRING 2 BLINKS PAUSE REPEAT OFF 2 SENSOR DEFECTIVE 2 CALL CUSTOMER SERVICE 3 BLINKS PAUSE REPEAT 2 SOURCE DEFECTIVE 1 SENSOR RECEIVING INTERFERENCE 1 ATTEMPT TO DETERMINE SOURCE OF INTERFERENCE 2 CALL CUSTOMER SERVICE 4 BLINKS PAUSE REPEAT eo 1 SOURCE NOT SENDING PULSES 1 CALL CUSTOMER SERVICE 2 CALL CUSTOMER SERVICE NOTE IF OPERATING PROBLEM EXISTS THE DOOR CAN BE CLOSED IF YOU 1 DISCONNECT THE STB SYSTEM FROM THE OPERATOR AND 2 HOLD WALL CONTROL BUTTON DOWN UNTIL DOOR IS CLOSED REMOTE CONTROL amp WIRELESS KEYPAD WILL NOT WORK WITHOUT STB CUSTOMER SERVICE 1 800 354 3643 or www geniecompany com MAINTENANCE amp TROUBLESHOOTING Use this guide to correct problems with your door operator If these solutions do not work call Customer Service A CAUTION Use only with included SERIES Il wall control Use of any other wall control can cause the door to operate unexpectedly and the light not to work PROBLEM Operator does not run from wall control Door starts for no reason Door starts down then stops before it s closed Door starts down then stops and goes back up Door will only run closed Door will only run open Remote control has less than 25 feet operating range Door starts up but stops before it s completely open Operator runs but door does not move
21. a Genie authorized dealer by calling the Genie Consumer Connection at 1 800 654 3643 If an authorized dealer provides warranty service Genie will not reimburse you or otherwise be responsible for those charges Your choice of any one of the above described service options is your remedy under this warranty What This Warranty Does Not Cover This warranty does not cover batteries which are considered replaceable parts installation commercial use defects resulting from accidents damage while in transit to our service location or damage resulting from alterations misuse or abuse lack of proper maintenance unauthorized repair or modifications of the product affixing of any attachment not provided with the product programming of the Remote Control Devices Safe T Beam adjustment cleaning staples through wiring pinched or broken wires Carriage disengaged Force Control adjustments door out of balance broken springs or cables power outages use of extension cords missing or damaged parts on discounted clearanced final sale or taped cartons phantom operations labor is not covered if Opener is functioning properly while technician is in garage fire flood acts of God or failure to follow the Owner s Manual This warranty is the only one we will give on your Genie product and it sets forth all our responsibilities regarding your Genie product There are no other express warranties State and Province Rights This warranty g
22. a de 8 pies 2 43 m ij Ai XI 34 95 N cessaire de rallonge du Screw Drive Rallonge de 30 dm 18 po prolongeant la course de l ouvre porte Screw Drive pour une porte de 2 4 m 8 pi de hauteur Universal Conversion Kit Converts any Garage Door Operator to a secure radio signal system Kit includes a Remote Control Receiver and Transformer Juego de conversi n universal Convierte cualquier abridor de puerta de garaje a un sistema de se al de radio seguro El juego incluye GIRU 1T EE Garage Door Operator Accessories Order Form un control remoto de abridor de puerta de garaje receptor y transformador E gt 33154R N cessaire de conversion universel Transforme tout ouvre porte de garage en syst me de s curit signal radio Comprend une KF ja EN t l commande d ouvre porte de garage un r cepteur et un transformateur 60 WATT Enhanced Rough Service Light Bulb Ensures proper equipment compatability LIGHTBULB Bombilla de 60 Vatios Asegura componente correcto de sistema Eclairage de 60 WATT Garantir componant exact par syst me Emergency Release Kit Provides access to garage from outside in the event of an electrical power failure Juego de pica porte de pestillo Permitir entrtada desde por fuera de garaje porque corte de el ctric o N cessaires de D clenchement de secours Le n cessaire de d clenchement de secours est concupour vous permettre d acc der votre garage depuis l ext rieur en cas de p
23. aciones no autorizadas del producto poner de ninguna fijaci n no proporcion con el producto programar de los Dispositivos del Mando a distancia de T de Rayo Segura el ajuste limpiar Los alambres pellizcados o rotos el Coche solt los ajustes del Control de la Fuerza la puerta fuera de equilibrio los primaveras o los cables rotos las fallas del poder el uso de cuerdas de extensi n perdiendo o las partes da adas en descontado clearanced la venta final o los cartones grabados las operaciones fantasmales el trabajo no se cubre si el Abrelatas funciona apropiadamente mientras t cnico est en el garaje el fuego la inundaci n los actos de la naturaleza 0 el fra Esta garant a es la nica que daremos a su producto Genie y estipula todas nuestras responsabilidades con respecto a su producto Genie No hay otras garant as expresas Derechos de estados y provincias Esta garant a le otorga derechos legales espec ficos y puede que usted tenga tambi n otros derechos que var an de estado a estado y de provincia a provincia Visitar Website nuestro en www geniecompanv com LA GARANTIE DE LA Svst mes d acces Professionnels The Genie Company Ce qu elle couvre toute d fectuosit de mat riau et tout d faut de fab rication constat s pendant l utilisation normale du produit par un indi vidu son domicile en conformit avec le Manuel de l utilisateur Pendant combien de temps S rie H4000A 2 Moteu
24. all control contact reverse mechanism may not Observe door runs to CLOSE limit switch prevent damage to the obstruction garage f not increase closing force by turning door or garage door operator CLOSE adjusting screw clockwise slightly about 1 16 turn Repeat until door runs to CLOSE limit switch Check door is fully closed f not move CLOSE limit switch toward door as necessary to achieve fully closed 3 Adjust closing force On front panel of power head find adjusting screw marked OPEN Fig 7 2 e Turn screw gently counterclockwise until it stops e Run operator using wall control Observe door runs to OPEN limit switch If not increase opening force by turning OPEN adjusting screw clockwise slightly about 1 16 turn Repeat until door runs to OPEN limit switch Check door is fully open f not move OPEN limit switch toward power head as necessary to achieve fully open SETTINGS CONTACT REVERSE FOR HELP 1 800 354 3643 OR GENIECOMPANV COM Limit switch adjustments must be completed before running contact reverse test 28 1 Test contact reverse Open door using wall control Lay 2 x 4 board on floor in center of garage door opening Fig 7 3 Close door using wall control Door should stop and reverse within 2 seconds of contacting the board If door does not reverse properly a Decrease closing force a small amount
25. anne de courant et lorsqu il STB Adapter Brackets 2 Used in conjunction with standard STB mounting brackets they provide additional clearance along with _ mounting options ADAPTER Bras adaptador por STB 2 Usado con bras normal por STB proveer espacio adicional 34430 S EG BRACKET Supports raccord du STB 2 Se servir en compagnie de supports normal du STB assurer espace suppl mentaire No C O D shipments Please include check or money order do not send cash Allow 3 4 weeks for delivery We accept Visa or Mastercard phone orders TOTAL ORDER TOTAL DEL PEDIDO COMMANDE TOTALE 1 800 354 3643 Please have part number and credit card ready SHIPPING amp HANDLING FLETE Y MANEJO MANUTENTION ET EXPEDITION 5 00 No se aceptan pedidos de pago contra entrega COD Sirvase incluir su cheque o STATE SALES TAX IMPUESTO DE VENTAS ESTATAL TAXE DE VENTE giro postal no env e dinero en efectivo Conc danos 3 a 4 semanas para la entrega Aceptamos pedidos telef nicos de Visa o Mastercard 1 800 354 3643 S rvase tener GRAND TOTAL GRAN TOTAL TOTAL GLOBAL b hu Bd en ill Please add local sales tax if vou reside in one of the states listed Pas d exp dition contre remboursement Veuillez inclure un cheque ou un mandat Ban E bancaire N envoyez pas d argent comptant Accordez de 3 4 semaines pour la California Georgia Maryland New York Virginia livraison Nous acceptons les commandes p
26. anual Emergency Release Allows the garage door to be opened or closed manually for emergencies or maintenance POWER HEAD EXPLODED VIEW FOR HELP 1 800 354 3643 OR GENIECOMPANY COM POWER HEAD PARTS LIST ltem Part Name ltem Part Name 1 Power Head Assembly M Terminal Strip A Cover By Series Model N No 8 32 x 1 2 Hex Washer Head Screw B Front Plate Assembly P 8 32 x 3 8 Slot Hex Washer Head Screw C Light Socket R Capacitor Isolator D Motor Parts 45 Bumper E Receiver Assembly 4 1 4 20 Shoulder Bolt Capacitor By Series Model 5 1 4 Flange Nut G Opto Wheel 39 Coupler Opto Luctor Assembly 41 No 8 32 x 3 8 Phillips Hex Head Screw J Sequencer Assembly 42 No 8 32 x 3 8 Phillips Pan Head Screw K Circuit Board Bracket 48 Mounting Straps L Transformer 49 Light Lens OPERATIONAL FEATURES INTELLICODE Access Security System Improves security of door operator by continuously changing the access code each time the remote control is used The door operator responds to each new code only once An access code copied from a working system and tried again will not control the door operator INTELLICODE 1 Button Remote Control Controls door operator by allowing the garage door to be opened and closed remotely INTELLICODE Multi Button Remote Control Operates multiple Intellicode equipped door operators Lighted Wall Button some models Operates door operator from inside garage DO NOT use with lighted wall console
27. ar t l phone avec paiement par carte de Connecticut Illinois Massachusetts Ohio Wisconsin cr dit Visa ou Mastercard 1 800 354 3643 Ayez sous la main le num ro dela pi ceet Florida Indiana New Jersey Tennessee celui de la carte de cr dit MAIL ORDER FORM TO SHIP ORDER TO ENVIAR MERCANCIA CON EXPEDIER MARCHANDISE POUR ENVIAR HACER UN PEDIDO DE MERCANCIA A NAME NOMBRE NOM METTRE LA POSTE LE ARRANGEMENT ADDRESS DIRECCI N ADRESSE The Genie Company 22790 Lake Park Blvd CITY CIUDAD VILLE STATE ESTADO TAT ZIP C DIGO POSTAL CODE POSTAL Alliance Ohio 44601 Prices subject to change without notice El precio est sujeto a cambios sin aviso Les prix peuvent subir des modifications sans pr avis
28. ble Fig 2 14 27 3 8 Hex head bolt LA g N QZ 28 3 8 Nut SECT 3 SAFE T BEAM INSTALLATION A WARNING There should be no electrical power to the operator while installing Safe T Beam System wires If you have plugged in the power cord UNPLUG IT NOW NOTE Operator will not close door automatically unless the Safe T Beam System is installed 1 Mounting brackets Mark both sides of garage door frame or wall 5 above floor Fig 3 1 Hold bracket 38 against door frame or wall Check if brackets extend out from wall far enough so tongue of bracket is beyond door tracks or any door hardware f not a STB bracket extensions are available at local dealer b Blocks of wood etc may be substituted for extensions Center bracket on your mark Fig 3 2 Fasten each with 2 screws 40 Fig 3 2 Tongues should point toward each other L 40 410 16 x 1 1 4 NOTE Mounting brackets can be attached to brick walls or concrete floor using masonry anchors not provided 2 Mounting STB source and sensor f garage has only one garage door Determine which side of garage receives most direct sunlight Fig 3 4 and place Red LED here whenever possible Fig 3 4 e For multiple doors Preventing crossed signals is critical Place source and sensor modules on adjacent doors facing in opposite directions Fig 3 4 NOTE To help prevent interference from
29. by turning the CLOSE force adjustment screw slightly counterclockwise b Test contact reverse again c Repeat steps a and b until contact Fig 7 3 reverse works properly If you don t have a 2 x 4 board handy any object 1 1 2 inches high that can withstand being hit by the garage door without sustaining damage is fine NOTE If door is stopping but not reversing CLOSE limit switch must be moved closer to door SE 8 BATTE R Y amp VISOR CLIP FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 1 Install replace battery Fig 8 1 Using a pen or similar object gently push in on tab Cover snaps open Remove old battery e Observe polarity markings inside battery compartment e Match new battery to polarity markings and instal new 4 EVEREADY 23 12 Volt battery Replace battery cover NOTE Use only 4EVEREADY A23 12 Volt battery 2 Attach visor clip Fig 6 1 Slide clip in slot on back of remote control Snap in place Visor Clip Battery Fig 8 1 SECT 9 PROGRAMMING REMOTE CONTROLS FOR HELP GENIECOMPANY COM PROGRAMMING REMOTE CONTROLS NOTE Each remote device must be programmed separately A WARNING Moving door can cause serious injury or death e Keep people clear of opening while door is moving e Do not allow children to play with remote controls If Safety reverse does not work properly Close door and disconnect operator using emergency r
30. cer sans frais de votre part Si nous envoyons les parties de replacement du produit il est possible que nous utilisions des pi ces de remplacement neuves ou reconditionn es Si nous d cidons de remplacer le produit Genie il est possible que nous le remplacions avec un produit neuf ou reconditionn de conception semblable Limites LES GARANTIES IMPLICITES Y COMPRIS LES GARANTIES D A DAP TA TION A UN USA GE PAR TI CU LIER ET LA GA RAN TIE DE VALIDITE MAR CHAN DE UNE GARANTIE TACITE QUE LE PRODUIT EST ADAPTE A L USAGE SONT LIMITEES A UN AN A COMPTER DE LA DATE D ACHAT GENIE DECLINE TOUTE RESPONSABILITE EN CAS DE PERTE D UTILISATION DU PRODUIT OU DE DOMMAGES MATERIELS CAUSES PAR LE PRODUIT GENIE OU PAR UN FONCTIONNEMENT DEFECTUEUX DE DOMMAGES ACCIDENTELS OU INDIRECTS DE DOMMAGES ISSUS DE L UTILISATION INCORRECTE OU DE LA MODIFICATION DU PRODUIT GENIE Certains tats et provinces n autorisent pas les limites de dur e des garanties implicites ou l exclusion des dommages accidentels ou indirects Dans ce cas les exclusions ci dessus ne s appliquent pas Comment b n ficier du service offert par la garantie Pour pouvoir en b n ficier il vous faut fournir une justification de la date et du lieu de l achat 1 Service pour effectuer les r parations soi m me Appeler le num ro sans frais du service la client le Genie 1 800 354 3643 Des agents Genie sp cialis s vous aideront diagnostiquer le probl me et prendront
31. des on a curved track 1 PIECE DOORS consist of one large panel and swivel on large spring loaded hinges on each side of door 1 Determining header bracket location e Find center of door from side to side Measure overall width of door example 16 feet Divide overall width by 2 example 16 2 8 feet Measure this distance from side of door and draw a pencil line vertically from the top of the door down approximately 1 foot This is the centerline Fig 2 1 Continue marking centerline on wall above door from top of door up approximately 1 foot Fig 2 1 TYPICAL TRACKLESS CENTERLINE H EMEN floor TYPICAL TRACK GUIDED CENTERLINE i garage d El o F Is na 4 Sectional doors mav have one torsion spring as shown or two springs one on each side Some older doors mav have extension springs INSTALLATION 2 Finding highest point of travel e While raising garage door manually watch top edge of door to see where it reaches its highest point This is called highest point of travel Fig 2 2 e A locking pliers can be used to hold the door in position by clamping it onto the rail A stool chair table or any object that can safely support door will also work With door held partly open at its highest point measur
32. die Einhaltung aller gesetzlichen Bestimmungen in anderen L ndern Sollen Sendeger te in anderen L ndern eingesetzt werden so muss der Importeur vor dem Gebrauch sicherstellen dass die Sendeger te auch solchen lokalen Bestimmungen entsprechen welche von den Bestimmungen der USA und Kanadas abweichen BIL T fai AH Tek DRE E EU ADAME DX FIR S 68 CR 2 38 n o UR 5 8 EAHA FH LIA ERA SRAM y SUA SR sz URS IDEAR gt hIILAZVA MEHM MDTAVJNARERUJNI DIK UMLZAD KIYASVI BYAUA PREROA FB DIO ESO TRRS A IZ MEMS SABA C EXWwubZLARvS AyYAUAGSGJZEUOJT4ERMO E Cf FH edu Xe MURO RE RINA EIAS C 315 DE LEBATZA ARD HAIL MARA Es OO ER TAZ ERRUJE EEA SMADIESSS ZIPA 19401 HE HE 47 HOF SHE SPAKE Ol telo 71E CHE BEHO 2E HA QF AO ES MOIS SIBLICI EMANJEEO JIE CHE KAUA ASE BS AXE ESPIAS nia 2 LICISIS QTAR CHI 22 1 xjeto 0158 zrsgaliot ELC A WARNING To reduce the risk of severe injury or death READ AND FOLLOW ALL INSTRUCTIONS Never let children operate or play with the Door Controls Keep the Remote Control away from children Always keep the moving door in sight and away from people and objects until the door is completely closed NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR NEVER GO UNDER A STOPPED PARTIALLY OPEN DOOR Test Opener monthly The door MUST reverse on contact with a 1 1 2 high
33. e distance from top edge to the floor Remove support and gently lower door Mark highest point of travel at centerline on wall above door Fig 2 3 NOTE Following step depends on type of door 3 Final header bracket mounting location e For SECTIONAL DOORS add 2 1 2 inches to highest point of travel and mark this height on centerline Fig 2 3 For ONE PIECE DOORS add 6 inches to highest point of travel and mark this height on centerline Fig 2 4 FOR HELP 1 800 354 3643 OR GENIECOMPANT COM Highest point of travel centerline of door L Highest point of travel 2 Measure from here to Highest point of travel Measure from here to floor Highest point of travel Ls _ ou Fi centerline of door A g 2 4 INSTALLATION FOR HELP 1 800 354 3643 OR GENIECOMPANY COM NOTE If torsion spring interferes with your final location mark bracket location 2 1 2 or 6 above torsion spring depending on garage door type 4 Check mounting location for strength Header bracket must be attached to framework of garage Fig 2 5 e If final header bracket position is on garage door header continue with step 5 e If final header bracket position is above garage door header a mounting plate must be installed and mounting location must be remarked before continuing with step 5 Fig 2 5 f your garage wall is finished covered with drywall contin
34. e to mid point of rail Place emergency release lever in engaged position 11 Flip assembly right side up Rail resting on carriage 12 Attach rail strap 13 Place rail strap against end of rail so that attached stud passes in front of end of rail Fig 1 16 e Line up rail strap holes with rail holes e Secure with 2 bolts 46 and 2 nuts 9 13 Make sure rail assembly is resting straight and level e FULLY TIGHTEN ALL BOLTS AND NUTS IN RAIL ASSEMBLY 5 16 Flange nut 46 5 16 x 3 4 Hex head bolt MAIN ASSE MB LY FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 079 release pi knob 14 Attach emergency release knob cord and tag Tie an overhand knot in one end of emergency release cord 17 Slide cord through center of knob 18 Fig 1 17 Slide cord through hole in emergency release lever on carriage Tie a second knot in this end Fig 1 18 Slip wire of emergency release tag 19 through hole in emergency release lever and twist it around itself 15 Attach limit switches e CLOSE limit switch 15B Switches are identical Place CLOSE limit switch over top of rail about 12 inches from rail strap Fig 1 19 Check that white lever is toward power head nsert set screw 16 into limit switch hand tight only to temporarily hold switch in place Fig 1 19A Attach brown wire to switch Fig 1 19B Leaving some slack in wire Fig 1 20
35. ed la vente finale ou a enregistr des boites les op rations fant mes la main d oeuvre n est pas couverte si l Ouvre boite fonctionne convenablement pendant que le technicien est dans le garage le feu l inondation les d sastres naturels ou l chec pour suivre le Manuel du Propri taire Cette garantie est la seule garantie fournie pour le produit et fait valoir toutes les responsabilit s qui vous incombent concernant le produit Genie Il n y a pas d autres garanties expresses Droits pour les tats et les provinces Cette garantie vous donne des droits juridiques sp cifiques les autres droits peuvent varier d un tat l autre et d une province l autre Visite Website notre en www geniecompanv com PHOTOCOPY THIS PAGE TO USE FOR ORDERING FOTOCOPIAR LA PAGINA POR USAR CUANDO HACER EN PEDIDO RENDRE APPAREIL PHOTOSTAT DU PAGE POUR USAGE A DISPOSITION Formulario de pedido de accesorios para abridores de puertas de garaje Formulaire de commande des accessoires pour ouvre porte de garage AVAILABLE AT YOUR LOCAL DISTRIBUTOR DISPONIBLE POR SU DISTRIBUIDOR LOCAL DISPONIBLE AUPR S DE VOTRE DISTRIBUTEUR LOCAL MODEL DESCRIPTION PRODUCT CODE PRICE US QTY SUBTOTAL MODELO DESCRIPCI N CODIGO PRECIO CANTIDAD SUBTOTAL MODELE DESCRIPTION CODE DU PRODUIT PRIX US QTE SOUS TOTAL Deluxe Remote Control with Intellicode Allows remote operation of garage door Controlador remoto de lujo con In
36. elease e Do not use door operator remote controls or wireless keypad e Refer to door and door operator owner s manuals before attempting any repairs NOTE Remote controls will not close door if Safe T Beam malfunctions NOTE When programming remote control it must be at least 24 inches from the antenna 1 Program one button remote e Lower lens cover Locate learn code button and learn indicator on power head Fig 9 1 Pressandrelease learn code button Red learn indicator blinks 2 times per second Press remote control button once within 30 seconds Red learn indicator stays lit Press remote control button again Red indicator goes out and memory is stored NOTE If red indicator blinks approximately 4 times per second programming has stopped If programming stops repeat above steps 2 Program multi button remote e Repeat step 1 above Program one button remote for each button and operator NOTE Each button on a multi button remote control is for a different operator You cannot use more than one button on a multi button remote for a single door 3 Operating remote Press button once f door is at up or down limit door will move away from that limit f door is stopped between limits it will move toward the limit where it was last stopped f door is moving it will stop NOTE Door automatically stops at end of open or close cycle Learn Button Fig
37. ency release The operator must reverse when the door contacts a 11 2 high object on the floor at the center of the doorway This is the size of a 2 x 4 board laid flat Visit our website at www geniecompany com NOTE Please keep original or photocopy of your sales receipt with this manual for future reference should service ever be required SAVE THESE INSTRUCTIONS SE T 1 MAIN ASSE MBLY FOR HELP 1 800 354 3643 OR GENIECOMPANY COM OPEN BLUE PARTS BAG NOTE 3 piece rail assembly is for doors up to and including 7 feet 6 inches high An extension for 8 feet doors is available 1 Set power head so that front panel with end of shaft and rail attachment flange is facing up Fig 1 1 NOTE If you have this type Carriage Stop skip Step 2 DO NOT install Bumber 2 Install bumper 45 Peel protective paper from glue side of bumper e Stick bumper into position as shown Fig 1 1 3 Install coupler 39 e Place coupler over end of shaft e urn it as needed until it engages with shaft It will drop down over end of shaft and will no longer turn freely Fig 1 1 4 Set power head on its bottom Fig 1 4 A CAUTION Drive screws can slide out of rail sections Keep rail sections level until operator is fully assembled 5 Attach 1 piece rail or first rail section 3A of 3 piece rail to power head e 3 piece only Select first rail section It has protective cardboard sleeve ov
38. ent parts for your Genie product we may use new or reconditioned replacement parts If we choose to replace your Genie product we may replace it with a new or reconditioned one of the same or similar design Limitations IMPLIED WARRANTIES INCLUDING THOSE OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY AN UNWRITTEN WARRANTY THAT THE PRODUCT IS FIT FOR ORDINARY USE ARE LIMITED TO ONE YEAR FROM DATE OF PURCHASE GENIE WILL NOT PAY FOR LOSS OF USE OF YOUR GENIE PRODUCT OR PROPERTY DAMAGE CAUSED BY YOUR GENIE PRODUCT OR ITS FAILURE TO WORK ANY SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES ANY DAMAGES RESULTING FROM MISUSE OR MODIFICATION OF YOUR GENIE PRODUCT Some states and provinces do not allow limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages so the above exclusions may not apply How to get Warranty Service To get warranty service for your Genie product you must provide proof of date and place of purchase of the product 1 Do It Yourself Service Call Genie Consumer Connection toll free at 1 800 354 3643 Trained Genie representatives will assist in diagnosing the problem and will arrange to supply you with required parts for do it yourself repairs Trained service representatives are available Monday Friday 8 00 AM 11 00 PM and on Saturday 11 00 AM 8 00 PM Eastern Time subject to holidays 2 Service From Authorized Dealers You can obtain the name of
39. er end of screw Fig 1 2 3 piece only Remove cardboard sleeve e Slide end of screw out about 5 inches Fig 1 3 Place bearing end of screw against coupler Fig 1 4 e urn screw until it engages with coupler e Slide rail section into rail attachment flange until holes in rail match up with holes in flange e Secure first rail section with 2 bolts 4 and 2 nuts 5 hand tight only Fig 1 5 e For 1 piece rail skip to step 8 39 45 Coupler Rubber bumper MAIN ASSEMBLY FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 6 Attach middle rail section 3B e Select middle rail section This section looks identical on both ends with each set of holes being about 4 inches apart Fig 1 6 e Find arrows stamped into side of rail Fig 1 7 e Align rail so arrows point away from power head e Slide screw toward power head so it sticks out end of rail section about 2 inches Fig 1 6 Fig 1 7 1 4 Shoulder bolt w flange 1 4 Flange nut MAIN ASSEMBLY FOR HELP 1 800 354 3643 OR GENIECOMPANY COM e Slide a collar 11 over exposed end of nens screw on middle rail as far as it will go T Fig 1 8 WW e Engage hook on middle rail with hook Hh ANT on first rail section Fig 1 9 vu CA e Slide collar toward power head so that it A now covers hooks Fig 1 10 e Snap a clip 12 onto screw behind collar to hold c
40. f not skip to step 9 Fia 6 1 If yes have an electrician perform steps 2 g through 8 CONNECT POWER WITH PERMANENT WIRING Instructions for electrician 2 Remove power from circuit 3 Remove motor cover Fig 6 1 e Remove 4 screws 41 from cover and slide off back of power head 4 Remove and discard power cord Cut off power cord inside power head NOTE There must be at least 6 inches of black and white wire inside the power head Between splice and entrance bushing Remove and throw away power cord strain relief and knock out 5 Install suitable entrance bushing 6 Connect permanent wiring to power head wires Safe T Beam Alignment Check Connect white supply line to white wire Connect black supply line to black wire After turning the electrical power on if the Connect ground to green wire ground STBs are not in proper alignment the red NOTE Use only U L recognized wire nuts LED Source will blink continuously 7 Replace motor cover Slide motor cover back on Replace and tighten 4 screws To correct the problem the brackets are 8 Reconnect power to circuit flexible and can be adjusted slightly to bring the system into alignment CONNECT POWER WITH PLUG When the STBs are in alignment the red LED 9 Plug in door operator will stop blinking and stay on See warning above Plug door operator into a grounded outlet Fig 6 2 Perform STB alignment check Fig
41. ght control Turns operator lights on and off without moving door 2 Wall Button Operates door from inside garage Fig 4 5 SECT 5 LIGHT LENS INSTALLATION 1 Install light bulbs e 2 bulbs No more than 60 watts each Do Not use short neck bulbs Whenever possible use bulbs rated for Hough service Vibration Appliances 2 Install lens Hook bottom hinges into slots at bottom of front plate Fig 5 1 Swing lens up over lights Check for alignment between the screw holes in the Lens and those on the metal front plate Lens will be fastened with 2 pan head screws 42 green parts bag Fig 5 2 DO NOT FASTEN YET Wait until you have completed programming the Remote Controls FOR HELP 1 800 354 3643 Fig 5 1 Fig 5 2 pan head screws secure top of lens b quu 42 8 x 3 8 Pan head screw SE C T 6 CONNE CTIN G P OWE R FOR HELP 1 800 354 3643 OR GENIECOMPANY COM A WARNING To reduce the risk of electrical shock this equipment has a grounded type plug that includes a third grounding pin This plug will only fit a grounded type outlet If you do not have a grounded outlet contact a qualified electrician to install one DO NOT alter the plug in any way The door operator must be properly grounded in order to prevent personal injury and damage to the components 1 Check local building codes Does building code require permanent wiring
42. ives you specific legal rights and you may also have other rights that vary from state to state and province to province Visit Our Website at www geniecompany com Sistemas de acceso profesional de Genie Company GARANT A LIMITADA Lo que est cubierto todo defecto en materiales y mano de obra en el uso dom stico personal y normal de acuerdo con el Manual del Propietario Duraci n Serie H4000A 2 Motor 10 a os y todas las dem s piezas 2 a os Serie H6000A 2K Motor 15 a os y todas las dem s piezas 3 a os Serie 15525 Motor 2 afios y todas las dem s piezas 2 a ios Serie IS550 1 Motor 7 afios y todas las dem s piezas 2 a ios Serie IS550 2 Motor 10 afios y todas las dem s piezas 2 afios Serie 15550 2 Motor 12 a os y todas las dem s piezas 2 a os Serie 15850 2 Motor Vitalicia y todas las dem s piezas 3 a os Serie IS900 1 Motor 10 a os y todas las dem s piezas 2 a os Serie IS900 2 Motor Vitalicia y todas las dem s piezas 2 a ios Serie 15920 Motor Vitalicia y todas las dem s piezas 2 afios Serie ISL950 Motor Vitalicia y todas las dem s piezas 3 afios Serie ISL980 Motor y todas las dem s piezas Vitalicia Serie CM7600 Motor 10 a os y todas las dem s piezas 3 a os Serie CM8600 Motor Vitalicia y todas las dem s piezas 5 a os Serie PRO 95 Motor y todas las dem s piezas Vitalicia Garant a Vitalicia se
43. m personal normal household use in accordance with the Owner s Manual For how long H4000A 2 Series Motor 10 years and all other parts 2 years H6000A 2K Series Motor 15 years and all other parts 3 years 15525 Series Motor 2 years and all other parts 2 years 15550 1 Series Motor 7 years and all other parts 2 years 15550 2 Series Motor 10 years and all other parts 2 years 15550 2 Series Motor 12 years and all other parts 2 years IS850 2M Series Motor Lifetime and all other parts 3 years 15900 1 Series Motor 10 years and all other parts 2 years 15900 2 Series Motor Lifetime and all other parts 2 years 15920 Series Motor Lifetime and all other parts 2 vears ISL950 Series Motor Lifetime and all other parts 3 years ISL980 Series Motor and all other parts Lifetime CM7600 Series Motor 10 years and all other parts 3 years CM8600 Series Motor Lifetime and all other parts 5 years PRO 95 Series Motor and all other parts Lifetime Lifetime warranty warranted for as long as you own your home Who Gets the Warranty The warranty is limited to the consumer who originally purchased the product Geographic Scope This warranty applies only to Genie products purchased in the United States and Canada What we will do f your Genie product is defective we will send replacement parts or at our option replace it at no charge to you If we send replacem
44. o retune remote controls Be sure door is in good repair properly lubricated and balanced Check OPEN limit switch setting See section 7 Check force adjustment See section7 Check for broken door spring Make sure carriage is engaged Check force adjustment See Section 7 Program remote control code into receiver memory See section 9 If one remote control works and another does not check battery remote control type Series II and frequency of non working unit See section 9 Be sure all fasteners are tight Be sure door is in good repair properly lubricated and balanced See Monthly Maintenance section Use self diagnostic STB System troubleshooting information to maintain safe operation See section 3 Check wiring Disconnect amp reconnect wires on wall control Non compatible wall control SECT 11 WIRING DIAGHAM A CAUTION Opening cover could cause electrical shock Remove power from operator prior to removing cover FOR HELP 1 800 354 3643 OR GENIECOMPANY COM ELECTRICAL SHOCK COLOR LEGEND PRIMARY POWER CORD SEQUENCER ABS CORDON DE ALIMENTACION SECUENCIADOR CLOSE CERRAR FERMER CABLE D ALIMENTATION PRIMARIO SEQUENCEUR OPEN ABRIR OUVRIR z x PRIMAIRE 2 lt l oO a WHITE LLI o 2 L a BLACK RED WHITE PRIMARIO PRIMAIRE PRIMARY TRANSFORMER TRANSFORMADOR TRANSFORMATEUR DE COURANT p Aa
45. ollar in place Fig 1 11 e Slide middle rail against first rail Place rail clamp 7 on each side of joint where rails meet Match up holes in clamps with holes in rail Edge with lip is bottom of clamp e Secure rail clamps with 4 bolts 8 and 4 nuts 9 hand tight only Fig 1 12 Collar O 5 16 Flange nut 5 16 Shoulder bolt w flange Fig 1 12 MAIN ASSE MB LY FOR HELP 1 800 354 3643 OR GENIECOMPANY COM NOTE If installing an extension kit for an 8 feet high door refer to the instructions included with the extension kit now E 7 Attach end rail section 3C e Attach eno rail in same way as middle rail step 5 End rail section screw has hook on one end only 8 Flip power head rail assembly over upside down so that entire length of screw is visible from above 9 Install carriage stop 6 e With bent tabs facing up slide carriage stop into rail Fig 1 13 Fig 1 13 Slide carriage stop along rail until it rests against power head 10 Install carriage 10 e Place emergency release lever in released position Fig 1 14 Make sure arrow on side of carriage Fig 1 14 is pointing away from power head Emergency release lever will be facing power head Slide carriage into rail Fig 1 15 NOTE Carriage can be used as a temporary support for the rail while performing the next few steps of assembly Slide carriag
46. r 10 ans et toutes les autres pi ces 2 ans S rie H6000A 2K Moteur 15 ans et toutes les autres pi ces 3 ans S rie IS525 Moteur 2 ans et toutes les autres pi ces 2 ans S rie 15550 1 Moteur 7 ans et toutes les autres 2 ans S rie IS550 2 Moteur 10 ans et toutes les autres pi ces 2 ans S rie 15550 2 Moteur 12 ans et toutes les autres pi ces 2 ans S rie IS850 2M Moteur vie et toutes les autres pi ces 3 ans S rie 15900 1 Moteur 10 ans et toutes les autres 2 ans S rie 15900 2 Moteur vie et toutes les autres 2 ans S rie IS920 Moteur vie et toutes les autres pi ces 2 ans S rie ISL950 Moteur vie et toutes les autres pi ces 3 ans S rie ISL980 Moteur et toutes les autres pi ces vie S rie CM7600 Moteur 10 ans et toutes les autres pi ces 3 ans S rie CM8600 Moteur vie et toutes les autres pi ces 5 ans S rie PRO 95 Moteur et toutes les autres pi ces vie Garantie vie Garanti tant que vous restez propri taire de votre habitation B n ficiaire de la garantie La garantie est limit e au client qui a achet initialement le produit Pays couverts Cette garantie s applique seulement aux produits Genie achet s aux tats Unis et Canada Nos conditions Si le produit Genie est d fectueux nous enverrons les parties de replacement ou selon notre choix de le rempla
47. s manual ets he brackets may be attached to concrete if necessary but extra tools and special fasteners not supplied will be required A WARNING NOTE 1 1 2 STB bracket adapters are available through your local Genie Dealer If your door sticks binds or is out of balance have it adjusted by a professional Door springs cables pulleys brackets and Is your garage door made of associated hardware are under extreme light weight steel aluminum fiberglass tension and can cause serious injury or or glass panels Additional support bracing death must be added to these type doors If this is the case please contact the door distributor or manufacturer so that they can furnish you with a bracing kit fa HomeLink E www homelink HomeLink is a universal A WARNING transceiver a combined DO NOT USE AN EXTENSION CORDI transmitter and receiver that provides a Extension cords can cause dangerous convenient Way to replace up to three hand held overheating conditions radio frequencv RF transmitters used to DO NOT USE A PORTABLE GENERATOR activate devices such as gate operators garage This pr i ian r n door openers entry door locks security systems A bog id jeb 2 and even home lighting Additional HomeLink information can be found at www homelink com alternate power supplies or by calling 1 800 355 3515 TYPICAL SECTIONAL DOOR INSTALLATION Q 2 ADDED SUPRORT HEADER BRAC
48. sembly NOTE The operator will not function unless the Safe T Beam system is installed and the force controls are properly set PARTS LIST Item Part Name Parts Required 3 Piece 33 Wall Console varies 34 6 x 1 1 4 Pan Head Screw 2 35 Entrapment WARNING Label 1 36 Safe T Beam STB System Sensor Green LED 1 37 Safe T Beam STB System Source Red LED 1 38 2 39 1 40 4 41 4 42 2 43 1 44 4 45 1 46 5 47 3 48 Mounting Straps 2 49 1 50 varies PARTS IDENTIFICATION FOR HELP 1 800 354 3643 OR GENIECOMPANY COM L AWARNING PHECAUCIOH ELLE GET NOTE Accessories vary by model remotes vary by model FASTENERS shown tull size See Parts List for description 1 4 Shoulder bolt w flange 48 32 x 3 8 Hex head screw 1 4 x 2 Lag screw 4 pin 5 Cotter pin _ Wm 3 8 Hex head bolt 10 x 1 1 4 Phillips hex head screw 8 x3 8 Hex flange head screw H8 x 3 8 Pan head screw 3 8 Nut SUA Wire clip Insulated staple Rubber bumper 5 16 x 3 4 Hex head bolt a 6 x 1 1 4 Pan head screw 1 4 20 Self drilling screw SAFETY INFORMATION PRE INSTALLATION WARNING OVERVIEW OF POTENTIAL HAZARDS Garage doors are large heavy objects that move with the help of springs under high tension and electric motors Since moving objects springs under tension and electric motors can cause injuries
49. sun STB sensors Green LED may be placed further from the door opening where they will spend more time in shadows Slide source sensor onto tongue of bracket until it clicks into place Fig 3 3 OPEN RED PARTS BAG 3 Wiring Route wire 29 using either method shown Fig 3 5 e Securely fasten wires to ceiling and walls as you go using insulated staples 30 Staples should be snug only Staples which are too tight can cut wires Jea Insulated staple THREE DOOR GARAGE FOR HELP 1 800 354 3643 SAFE T BEAM INSTALLATION FOR HELP GENIECOMPANY COM A CAUTION Staples which are too tight can cut or pinch wires Cut or pinched wires can cause the STB System to stop working When using the insulated staples make sure you fasten them only as tightly as needed to hold the wire snugly Make wire attachments at STBs Split and strip wire ends to be connected as shown Fig 3 6 Loosen terminal screws Fig 3 6 Insert wire under flat plate and tighten screw It does not matter which wire white or striped goes on which terminal Fig 3 7 Make wire attachments at power head SIBs are connected to terminals 3 and 4 on power head Fig 3 8 It does not matter which wire white or striped goes on which terminal 4 Check the following Ensure that part of door or its hardware is in path between lenses of source and sensor e Ensure that tops of lenses are between 5 6 above
50. tellicode Proporci nar operaci n remoto de la puerta del garaje 33060R 34 95 T l commande de luxe avec Intellicode Permettre op ration loign de porte de garage 2 Button Remote Control with Intellicode Allows remote operation of 2 garage doors Controlador remoto de 2 funciones con Intellicode Proporci nar operaci n remoto de dos las puertas del garaje 330695 44 95 T l commande 2 fonctions avec Intellicode Permettre op ration loign deux portes de garage 3 Button Remote Control with Intellicode Allows remote operation of 3 garage doors 2 Controlador remoto de 3 funciones con Intellicode Proporci nar operaci n remoto de tres las puertas del garaje 33069T 49 95 T l commande 3 fonctions avec Intellicode Permettre op ration loign trois portes de garage Lighted Wall Console Operates Garage Door Independent light control Security vacation lock Consola de pared de 3 funciones Acciona la puerta del garaje Control de luz independiente Cerradura de seguridad para vacaciones Y 34292R 34 95 Console murale trois fonctions Actionne la porte de garage Commande d clairage ind pendante Interrupteur de verrouillage de s curit lt lt 3 Button Mini Remote Control with Intellicode Fits easily into pocket or purse BB Minicontrolador remoto de 3 funciones con Intellicode Cave f cilmente en el bolsillo o cartera Ny 39 95 Mini t l commande 3 fonctions avec Intellicode
51. th all United States and Canadian legal requirements as of the date of manufacture No warranty is made that they comply with all legal requirements of any other jurisdiction If transmitters are to be used in another country the importer must determine compliance with any local laws and regulations which may differ from United States and Canadian requirements prior to use Los transmisores cumplen con todas las reglamentaciones legales de los Estados Unidos y del Canad en la fecha de fabricaci n Ninguna garant a se da que cumplan con todas las reglamentaciones legales de ninguna otra jurisdicci n Si los transmisores se van a utilizar en otro pa s el importador debe determinar si cumplen con las reglamentaciones y leyes locales que puedan ser diferentes a las reglamentaciones de los Estados Unidos y del Canad antes de usar los mismos Les metteurs sont conformes la r glementation am ricaine et canadienne compter de leur date de fabrication Aucune garantie n est stipul e indiquant qu ils sont conformes toutes les prescriptions juridiques d autres autorit s Si les metteurs sont utilis s dans d autres pays il incombe importateur d en d terminer leur conformit aux lois et r gles locales pouvant diff rer de celles des tats Unis et du Canada avant toute utilisation desdits metteurs Sendeger te entsprechen allen gesetzlichen Bestimmungen in den USA und Kanada zum Zeitpunkt der Herstellung Wir bernehmen keine Gew hrleistung f r
52. the floor Fig 3 9 The brackets are flexible and can be adjusted slightly if needed NOTE Safe T Beam alignment check will be performed following connection to electrical power see page 26 DO NOT PLUG IN YET See Illustration on page 3 for a full view of Safe T Beam location top edge of lens between 5 6 above floor Fig 3 9 SECT 4 WALL CONTROL INSTALLATION FOR HELP 1 800 354 3643 A WARNING Power must be removed before attaching wires Be sure ends do not touch each other or other terminals A CAUTION Use of any other wall control can cause the 1 1 4 to 1 1 2 door to operate unexpectedly and the light not to work Cut or pinched wires can cause door operator to malfunction Drive staples just tight enough to hold wire 1 Run wire from power head to wall control e Find location for wall control Insight of door and away from moving parts At least 5 feet from floor so small T AR BN children cannot reach it l Sem L Route wire from wall control to power head oso AN TL ri Y 2 A H A n FU ki je LE y dC i 1 a Use staples to Padi wire to ceiling and wall CO Ae E a pa L M NOTE Use only staples included 1 afl 2 Split wires at ends and remove 1 2 inch of E insulation from end of each Wire Fig 4 1 3 Attach wires to terminals Fig 4 2 Fig 4 3 Loosen Do Not Remove screws from Terminals at power
53. ue with step 5 OPEN ORANGE PARTS BAG 5 Mounting preparation Hold bracket against wall where final header bracket height crosses centerline e Make sure flange where rail strap attaches is on centerline Fig 2 6 Mark screw hole locations f your wall is finished take a small finish nail and gently tap it through drywall where you have marked screw holes to find out if there is wood behind mounting location If your marked location is solid continue with step 6 If your marked mounting location is not solid a mounting plate must be installed and mounting location remarked before continuing Fig 2 7 and Fig 2 5 6 Mount header bracket 20 Drill 5 32 inch pilot holes at marked screw hole locations e Fasten header bracket using 3 lag screws 22 eo E 22 1 4 x 2 Lag screw wooden plate fastened to wall studs di ii c t header TYPICAL UNFINISHED WALL floor ceiling TYPICAL FINISHED WALL Fig 2 5 flange for rail strap Fig 2 6 flange for rail strap wooden plate fastened to wall studs l 5 TALLATI ON FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 7 Attaching rail to header bracket e Gently set power head on garage floor while leaning rail strap against header bracket It is recommended that you place a piece of cardboard or similar material between power head and floor to prevent scrapes and scratches to power head NOTE It ma
54. y be necessary to support power head above floor As little as a few inches or as much as 5 or 6 feet depending on position of torsion spring s Be sure to use a stable support device such as a ladder e Slide threaded stud of rail strap through hole in flange of header bracket e Fasten with nut 9 finger tight only Fig 2 8 5 16 Flange nut l N S TA L LA TI ON FOR HELP 1 800 354 3643 OR GENIECOMPANY COM 8 Mounting power head e Raise power head and support it high enough that you can manually raise garage door fully open e Line up power head and rail with center of door Fig 2 9 e Keeping power head centered mount to ceiling at proper height a for sectional doors rail should be level with floor or slightly below level Fig 2 10 b for 1 piece doors rail should clear door by about 2 inches Fig 2 10 i 1 PIECE MUST CLEAR DOOR BY 2 INCHES AT HIGHEST POINT OF TRAVEL Fig 2 10 using one of the preferred methods shown Fig 2 11 mount power head It is possible to use other mounting methods The critical point to remember is that the mounting assembly must be solidly attached and able to support the weight of the power head DO NOT ATTACH TO DRY WALL OR SUSPENDED CEILING It must be anchored to the framework of the garage Fully tighten rail strap nut INSTALLATION
55. your safety and the safety of others depend on you reading the information in this manual If you have questions or do not understand the information presented call your nearest service representative In this section and those that follow the words Danger Warning and Caution are used to emphasize important safety information The word A DANGER means that severe injury or death will result from failure to follow instructions A WARNING means that severe injury or death can result from failure to follow instructions A CAUTION means that property damage or injury can result from failure to follow instruction The word NOTE is used to indicate important steps to be followed or important considerations POTENTIAL HAZARD EFFECT PREVENTION Keep people clear of opening while door is WARNING 9 9 Can Cause Do Not allow children to play with the door Serious Du operator or Deat Do Not operate a door that jams or one that has a broken spring WARNING Turn off power before removing operator cover Can Cause When replacing cover make sure wires are not Serious Injury pinched or near moving parts or Death Operator must be properlv grounded ELECTRICAL SHOCK Do Not try to remove repair or adjust springs or anything to which door spring parts are fastened such as wood blocks steel brackets cables or other like items WARNING Can Cause Serious Injur HIGH Repairs and adjustments must be made by a
Download Pdf Manuals
Related Search