Home

GE Monogram Built-In All-Refrigerator/Freezer Refrigerator User Manual

1. INSTALL FRAMED PANELS Right hand models shown Use the same instructions for left hand models TRIMMED MODELS ONLY IF YOU ARE INSTALLING OVERLAY PANELS GO TO STEP 10A 4 Door Trim Use Front Holes A to Secure Trim Use Rear Holes to Secure Handle Standard supplied handle shown in 1 4 panel position Install Door Panel e Open the door to 90 Remove the 6 Phillips head screws e There are two sets of holes in the handle side trim from the door handle Replace the handle side trim by installing the original e Remove the handle Retain all screws screws in the FRONT screw holes e Remove the 6 screws holding the trim lift off the trim e Secure the handle to the door using the REAR Retain the screws screw holes Slide the framed panel into the door trim 18 Installation Instructions STEP 9A INSTALL OVERLAY PANELS Use Front Holes to Secure Handle gt 7 il Use Rear Holes to Secure Trim Install Door Panel e Open the door to 90 Remove the 6 Phillips head screws from the door handle e Remove the handle Retain all screws e Remove the 6 screws holding the trim lift off the trim Retain the screws Slide the overlay panel into the door trim Custom Handles If you are using custom hand
2. L rods can be found in the upper left and right corners of the unit in the access compartment Look through the access compartment to make sure the rods line up with the anti tip bracket e There are 2 washers and a hair pin cotter per rod Remove the washers and hair pin cotter from the end of the rod e Rotate and move the L rod into the slot in the anti tip L Rod Pointing Down bracket tab Once it is in the slot rotate the L rod chgaged n Bracket so the hook portion is pointing down The holes at the front end of the rod should be in a vertical position Do this to both sides e Pull out on the end of the rod to make sure it is secure in the bracket e Locate the hole on the rod that is closest to the unit A hair pin cotter will be put through this hole to secure the rod If this hole appears to be too far away for a snug fit against the unit add the washers one at a time until the pin will fit tightly into the hole e Align the straight section of the pin with the hole from the underside of the rod Push the pin up until it snaps 7 into position Pliers may be used NOTE The hair pin Wall air cotter must be vertical when this step is completed to ensure the L rod is engaged in the bracket e Check the rod for tightness by pulling forward If the rod moves remove the hair pin cotter and place another washer on the rod Reinsert the pin e Bend the left grille back into place freezer only and repl
3. e Les r parations doivent tre faites par un technicien qualifi For Monogram local service in your area 1 800 444 1845 For Monogram service in Canada 1 800 561 3344 For Monogram Parts and Accessories call 1 800 626 2002 www monogram com Step 7 Adjust Door Swing Step 8 Install Grille Panel Step 9 Install Framed Panels Step 9A Install Overlay Panels Step 10 Connect Water Supply Step 11 Start Icemaker Step 12 Install Toekick Design Guide THE INSTALLATION SPACE 35 1 2 Finished Width gt A The finished 2 5 16 Wall View cutout width must be E Ss ue 35 1 2 ge Electrical Area 24 Minimum Cutout Depth 84 1 2 max 75 1 2 From 83 1 2 min Floor to Bottom Finished upply of Electrical Area Opening 1 2 ie gt A 3 1 2 3 1 2 Water And Electrical Locations Electrical and water supply must be located as shown The Cutout Depth Must Be 24 Minimum The unit will project forward slightly beyond adjacent cabinetry depending on your installation Cutout Depth Beneath a Soffit When installed beneathh a soffit the soffit cannot exceed the 24 installation depth shown The top case trim overlaps the bottom of the soffit Additional Specifications e A115 volt 60Hz 15 or 20 amp power supply is required An individual properly grounded branch circuit or circuit breaker is recommended Install a properly
4. 31 46148 224D2601P001 monogram com Installation Instructions 36 Built In All Refrigerators and All Freezers Monogr Safety Information BEFORE YOU BEGIN Read these instructions completely and carefully IM PORTANT Save these instructions for local inspector s use Observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions with your Owner s Manual for future reference AWARNING This appliance must be properly grounded See Grounding the Unit page 10 AAVERTISSEMENT Cet appareil doit tre correctement mis la terre Consulter Mise la terre de l appareil m nager page 10 If you received a damaged product you should immediately contact your dealer or builder ACAUTION Due to the weight and size of this product and to reduce the risk of personal injury or damage to the product THREE PEOPLE ARE REQUIRED FOR PROPER INSTALLATION APRUDENCE A cause du poids et de la taille de ce produit et pour r duire le risque de blessure et de dommages IL FAUT TROIS PERSONNES POUR FAIRE L INSTALLATION CORRECTEMENT CONTENTS Design Guide The Installation Space Dimensions and Clearances 130 Door Swing 90 Door Swing Customization Basics Panel Dimensions Side Panels ZUG2 Grille Panel Dimensions Grounding the Unit Step 5 Level Unit
5. at this height e Locate at least 2 studs on the back wall Mark these points on the horizontal line e Place the bottom of the wall bracket with tabs on the horizontal line Align the center notch on the bracket with the center line on the wall e The anti tip wall bracket has a series of holes Select 2 holes that match with the located studs Make sure the holes selected are on the center of the studs Mark the wall at these points e Mark an additional hole at each end of the bracket If one of the studs is closer to the end of the bracket mark an additional hole towards the center of the bracket e Drill 1 2 holes into the wall board at the locations marked for the toggles to be mounted not the stud markings e Drill 3 16 holes into wooden studs where marked If steel stud construction drill 1 2 holes into the studs where marked You will use 2 toggles with the metal studs Center Wall Bracket Two Additional Hole Locations at Ends of Brackets Wall Studs Line On Wa Installation Instructions STEP 4 INSTALL ANTI TIP BRACKET cont Install Wall Toggles The wall toggles and bolts can be ordered as Service Kit WR49X10193 Wall toggles are installed in the drywall and metal studs for stability Install the wall toggles as follows e Drill 1 2 holes at the wall markings made in the holes at the ends of the wall bracket
6. bottom of the grille e Pull the bottom of the grille forward down and out to remove Screws Freezer Unit e Open the access door e Using a 1 4 hex driver remove the 2 screws at the bottom of the grille on the right e Pull the bottom of the grille forward down and out to remove e Using a 1 4 hex driver remove the screw on the left side of the grille e The grille is aluminum and will bend easily Gently pull forward on the left side of the grille to open for access This grille will not be completely removed Screws 14 Power Cord Locate the power cord inside the left cavity If it has not been adjusted so the plug is easily accessible do so now L Bolt Left Grille Open Power Cord Location Move Unit into Final Position e Move refrigerator toward its final installed location Align the tabs on the wall bracket with the openings in the back of the unit e The unit has L bolts in the upper left and right corners inside of the access compartment These bolts will interlock with the wall bracket and secure the unit using the washers and hair pin cotters in the hardware kit once the unit has been leveled and is in the final position Installation Instructions STEP 5 LEVEL UNIT All models have 4 point leveling The front is supported by leveling legs the rear is supported by adjustable wheels Both are accessible from the front of the unit e To level the back of the unit turn t
7. on carpeted flooring DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG FROM THE POWER CORD DO NOT USE AN ADAPTER PLUG TO CONNECT THE UNIT TO A 2 PRONG OUTLET DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE Installation Instructions STEP 1 REMOVE PACKAGING ACAUTION Product is much heavier at the top than at the bottom be careful when moving When using a hand truck handle from side only A PRUDENCE ie produit est beaucoup plus lourd en haut qu en bas Il faut tre prudent lors des d placements Si un diable est utilis il faut soulever le r frig rateur sur le c t seulement e Carefully cut banding at the top and bottom remove outer carton e Slide out back corner posts 2 e Slide carton off top of cabinet NOTE IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID ACAUTION DO NOT lay this unit on its back A PRUDENCE ne pas mettre cet appareil m nager sur son dos STEP 2 INSTALL WATER LINE e A cold water supply is required for automatic icemaker operation The water pressure must be between 40 and 120 p s i e Route 1 4 OD copper or GE SmartConnect plastic tubing between house cold water line and the water connection location e Tubing should be long enough to extend to the front of the unit Allow enough tubing to accommodate bend leading into the water line connection NOTE The only GE approved plastic tubing is suppli
8. the side case trim Secure the panels to the unit with stick on hook and loop fastener strips Order the side panels from the cabinet manufacturer e Cut a notch in the top front corner as shown to allow clearance for corner keys in the front side trim Depending on installation height ZUG2 GRILLE PANEL DIMENSIONS The ZUG2 unified grille panel kit provides for the installation of a framed or overlay grille panel i A Grille Panel A Framed Panel Dimensions A Width B Height 1 4 Framed Panel 69 7 8 8 7 8 Overlay Panel Dimensions A Width B Height 1 4 Backer Panel 69 7 8 8 7 8 0 10 Spacer Panel 68 1 2 7 5 8 3 4 Overlay Panel 70 1 8 9 IMPORTANT NOTE The maximum weight for the unified grill is 25 pounds en Panel F _ Spacer Panel ye a Backer Panel Assemble the overlay panels in the same manner as the door panel Installation Instructions TOOLS REQUIRED Tin snips to cut banding et 2 Phillips screwdriver Drill and 1 2 3 16 bits A 1 4 1 2 5 16 7 16 socket Safety glasses SEES Pliers Appliance hand truck Stud finder 7 16 and 1 1 4 open end wrench GROUNDING THE UNIT IMPORTANT Please read carefully FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED The power cord of this appliance is equipped with a three prong grounding p
9. 3 7 8 ase Behind rame 4 stainless and trimmed models 5 Pro models Allow 25 minimum clearance for a full 130 door swing Allow 15 for pan removal For a 90 door swing allow 4 minimum clearance to a wall for framed and stainless steel models Allow 5 minimum clearance for professional models If the 90 doorstop position is used pan access iS maintained but pan removal is restricted See illustrations pages 5 and 6 to determine door swing interaction with adjacent cabinets or countertops Design Guide CLEARANCES 4 Min to Wall ele lt 25 Min to 130 Door Wall Swing 90 Door Swing These units are equipped with a 2 position door stop The factory set 130 door swing can be adjusted to 90 if clearance to adjacent cabinets or walls is restricted Order WX14X99 door stop for precise settings between 90 and 130 When Installed into a corner Allow 25 for a full 130 door swing Allow 15 for pan removal Allow 4 min clearance when door swing is adjusted to a 90 opening for pan access but pan removal is restricted 25 Minto 430 Door 130 Door Swing Swing Br Clearances for Multiple Single Door Installations In a side by side installation of a left and right door swing product a 1 clearance between the units is required Order ZUGSS2 Stainless Steel Unifi
10. 5 ge com
11. Installation Instructions Tools Hardware Materials 1 Step 1 Remove Packaging 1 Step 2 Install Water Line Step 3 Install Side Panels Step 4 Install Anti Tip Bracket Step 6 Secure Unit to Wall 1 Skill Level installation of this product requires basic mechanical carpentry and plumbing skills Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owner s Manual for warranty information AWARNING e These units are top heavy and must be secured to prevent the possibility of tipping forward Anti Tip protection is required See page 12 for details e Use this appliance only for its intended purpose e Immediately repair or replace electric service cords that become frayed or damaged e Unplug the unit before cleaning or making repairs e Repairs should be made by a qualified service technician AAVERTISSEMENT e Ces appareils m nagers sont lourds en haut et il faut les arrimer pour viter leur basculement Il faut avoir un syst me de protection contre le renversement Voir les d tails page 12 e ne faut utiliser cet appareil que pour l utilisation appropri e e R parer ou remplacer imm diatement tout cordon lectrique effiloch ou endommag e faut d brancher l appareil m nager avant le nettoyage ou toute intervention
12. M 5 1 2 i i u Electrical HL 3 Area 24 Minimum i Cutout Depth 75 1 2 From Floor to Bottom of Electrical Area Cold Water i Cold Water 84 1 2 max Supply 83 1 2 min Finished Opening Design Guide Frameless Cabinets The case trim overlaps cabinets at the top and sides Therefore frameless cabinets may require filler strips to prevent interference with cabinet door Refrigerator swing The opening must allow for filler strips or Freezer 23 7 8 From Rear of Unit Case Trim z Cabinet Front 3 4 Overlay a Panel DS Nominal Size Top View 130 DOOR SWING factory setting Scale 1 1 Design Guide Refrigerator Frameless Cabinets or Freezer The case trim overlaps pr Case Trim cabinets at the top and sides Therefore frameless cabinets may require filler strips to prevent interference with cabinet door swing 23 7 8 The opening must allow From Rear of for filler strips Unit Cabinet Front 3 4 Overlay A Panel Top View Nominal Size 90 DOOR SWING optional setting Scale 1 1 Design Guide CUSTOMIZATION BASICS Framed Or Overlay Panels Custom Handles and Accessory Kits Professional Style Stainless Steel Models Stainless steel wrapped refrigerators have beveled edge
13. ace the screws e Replace the flat grille panel by sliding it under the flange at the top of the access compartment and pushing the grille back into place Replace screws L Rod Washer i Hair Pin Cotter is Vertical 16 Installation Instructions STEP 7 ADJUST DOOR SWING STEP 8 INSTALL GRILLE PANEL NOTE This refrigerator has a 2 position door stop TRIMMED MODELS ONLY When space does not allow the door to swing open e Raise the access panel to the stop position fully to 130 you may change the door swing to a 90 opening Skip this step if door opening is satisfactory for your installation situation Pin Location For 90 Door Swing Pin Location as Shipped For 130 Door Swing de e Loosen the screws on the side trim behind the frame Remove the bottom trim e Slide the panel over the metal baker panel and into the trim e If necessary tap with a wood block until the panel slips under the top trim piece e Reassemble the bottom trim Tighten the screws e Adjust the hinge spring to accommodate the panel weight if necessary e Open the door to view the bottom hinge Note the door stop pin locations The pin is factory installed in the 130 position e Close the door From below use pliers to unscrew the door stop and reinstall into the 90 position 17 Installation Instructions
14. e Hold the metal channel flat against the plastic straps and slide the channel through the hole Plastic Straps VN iS C5 E Metal Channel e Gently pull back at the ends of the plastic straps to make the channel rest flush behind the wall e Hold the ends of the straps in one hand and slide the plastic cap along the straps until the flange of the cap is flush with the wall Cap N jas El a e Place your thumb between the plastic straps and bend up and down to snap the straps off at the wall F 13 Install Screws and Bolts e Have someone hold the wall bracket centered in place with each of the holes aligned with the correct opening in the bracket and level with the horizontal line e Insert the lag screws through the bracket and into the stud Tighten with a wrench Wood Stud Lag Screw werk Anti Tip Wall Bracket e Insert the bolts into the toggle by hand until snug Tighten with a wrench Drywall or Steel Stud Bolt ecu a iil Wall Toggle Anti Tip Wall Bracke Installation Instructions STEP 4 INSTALL ANTI TIP BRACKET cont Remove Grilles for Access to Power Cord and Anti tip Locking Hooks Fresh Food Unit e Open the access door e Using a 1 4 hex driver remove the 2 screws at the
15. ed in the GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Other types of plastic may crack or rupture with age and cause water damage to your home GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 2 6m WXx08X10002 6 1 8 m WxX08X10006 15 4 6 m WX08X10015 25 7 6 m WX08X10025 STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels If you are using 1 4 side panels they should be inserted into the case trim csom AM CAUTION Handle Trim DO NOT ATTEMPT TO ROLL UNIT OFF SKID Anti Tip Bet APRUDENCE we IL NE FAUT PAS ESSAYER DE Remove FAIRE ROULER L APPAREIL Tie Downs M NAGER POUR L ENLEVER ES Eo DE LAY PALETTE e The unit is secured to the skid with 4 slotted tie down straps Remove the four 5 16 bolts from the base channels in the tie downs e Remove toekick custom handle trim and wall bracket Set aside for final installation e Lift the unit off the skid with an appliance dolly Handle from the sides e Remove the four 7 16 bolts securing the tie down brackets to the skid Cold Water Supply 3 1 2 3 1 2 Shut off the main water supply Turn on the nearest faucet long enough to clear the line of water e Install a shut off valve between the icemaker water valve and cold water pipe in a bas
16. ed Grille Panel Kit or ZUG2 Custom Panel Unified Grille Panel Kit for one continuous grille panel ZUG2 ZUGSS2 Unified Grille Panel Kit e If you are installing two units side by side the installation space must be 71 1 2 wide Note Additional cutout width may be required when side panels are used Add side panel thickness to the finished cutout to calculate rough in width e The water and electrical locations for each product must be located as shown e A separate 115V 60Hz 15 or 20 amp power supply is recommended for each product Clearances for two products installed side by side with the same left or right door swing Allow 2 minimum clearance between the products to prevent door swing interference Order the WX14x99 adjustable door stop to reduce the factory set 130 door swing Allow 15 minimum to a wall to achieve full drawer extension and pan removal NOTE ZUG2 and ZUGSS2 Grille Panel Kit will NOT fit this installation Clearances for two products installed side by side with right and left side hinges together Allow 5 minimum between the two products to prevent one door from striking the other Use the WX14x99 adjustable door stop to reduce the factory set 130 door swing and to allow pan removal NOTE ZUG2 and ZUGSS2 Grille Panel Kit will NOT fit this installation 71 1 2 Finished Width t h sis ps Electrical u u Pa N HAN E 5 1 2
17. ement or cabinet The shut off valve should be located where it will be easily accessible e Turn on the main water supply and flush debris Run about a quart of water through the tubing into a bucket Shut off water supply at the shut off valve NOTE Saddle type shut off valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber Fasten the panels to the unit with stick on hook and loop fastener strips before setting unit in place Installation Instructions STEP 4 INSTALL ANTI TIP BRACKET AWARN N G ANTI TIP PRECAUTIONS The unit is top heavy and must be secured to prevent the possibility of tipping forward A ATTENTION precautions contre LES BASCULEMENTS L appareil m nager est beaucoup plus lourd en haut et il faut le maintenir en place pour viter la possibilit de son basculement vers l avant e The kit supplied with the unit contains 2 lag bolts and 4 toggles with bolts The wall bracket will be attached to the wall in 4 places e Measure the opening where the unit is to be installed Mark the center with a vertical line e Measure up 81 1 2 from the floor Mark this point on the wall e Using a level draw a horizontal line on the wall
18. et manufacturer This design provides a seamless appearance which integrates smoothly with surrounding cabinetry l m 3 4 Overlay Panel 10 Thick Spacer Panel 1 4 Thick Backer Panel Standard Door Handle Standard supplied handles shown in 3 4 overlay panel position Door Handle The standard supplied handles can be adjusted to accommodate both framed or overlay panels Custom handles of your choice supplied by your cabinet maker can also be installed on overlay panels If desired you may order ZKHSS2 Monogram stainless steel tubular handle kit for 3 4 overlay panels This kit contains 2 handles Only 1 kit is needed if installing these units as a pair Side Panels Side panels must be used whenever the sides of the product will be exposed Accessory Panels Black and stainless steel accessory panels are available from your Monogram dealer Panels are cut to size and ready to install ZPBS360 Black ZPSS360 Stainless Design Guide 1 4 FRAMED PANEL DIMENSIONS If you choose to install framed panels they must be cut to gt f ee 5 16 the dimensions shown The panels will slide into the frame Trim on the door and grille Reveal If the custom panel is less than 1 4 thick and if it fits loosely in the door frame it can be backed up with a piece of filler material or foam tape to improve the fit IMPORTANT NOTE Maximum weight for door panel is 67 pounds Maxim
19. grounded 3 prong electrical receptacle recessed into the back wall Electrical must be located on rear wall as shown Note GFI ground fault interrupter is not recommended e Water line can enter the opening through the floor or back wall The water line should be 1 4 O D copper tubing or GE QuickConnect kit between the cold water line and water connection location long enough to extend to the front of the unit Installation of an easily accessible shut off valve in the water line is required DIMENSIONS AND CLEARANCES 5 25 3 8 Framed Models Case Width 25 3 4 Stainless Steel Models Case Depth Shipping height The p product can be adjusted to fit into a cutout that ae is 83 1 2 min to 84 1 2 a A 84 From max height Note that 83 1 2 Tie Frome the top case trim at the front is 1 2 higher and will overlap upper cabinetry or soffit Use leveling legs and wheels for a maximum 1 height 4 adjustment T 36 Frame to Frame Width Depth Including Handles 26 7 8 Framed Models 27 3 4 Stainless Steel Models 28 11 16 Professional Models P Product Clearances These units are equipped with a 2 position door stop The factory set 130 door swing can be adjusted to 90 if clearance to adjacent cabinets or walls is restricted Order WX14X99 door stop for precise settings between 90 and 130 130 Door Swing 90 Door Swing 25 lies Minimum Minimum to Wall to a Wall 90 Door Swing H4
20. he 7 16 hex nut located above the front wheels Turn clockwise to raise or counterclockwise to lower the unit e For front leveling use a 1 1 4 open end wrench e Adjust height of unit to match installation cutout opening 83 1 2 to 84 1 2 The unit should be level and plumb with cabinetry Hex Nut Adjusts Rear Wheels Leveling Leg ACAUTION The rear leveling wheels and front leveling legs are limited to a maximum height adjustment of 1 If the installation requires more than 84 1 2 height the installer should elevate the unit on a sheet of plywood or runners Cabinetry trim could also be added across the top of the opening to shorten the opening If you attempt to raise the unit more than 1 you will damage the front leveling legs and the rear leveling wheels APRUDENCE Les roues de nivellement arri re et les pattes de nivellement avant permettent un r glage maximal de 25 mm 1 po Si l ouverture pour l appareil m nager a une hauteur sup rieure 2 15 m 84 1 2 po l installateur doit lever l appareil m nager sur une feuille de contre plaqu ou des glissi res Il est galement possible d ajouter des baguettes de finition des placards sur le haut de l ouverture afin de la r duire Lever l appareil m nager de plus de 25 mm 1 po endommage les pattes de nivellement avant et les roues de nivellement arri re 15 Installation Instructions STEP 6 SECURE UNIT TO WALL e The
21. les the handle must be properly secured to the panel before sliding the panel into the trim e The cabinet manufacturer will supply the custom handle and hardware e Secure the door trim using new handle side trim Discard the supplied handle 19 Right hand models shown Use the same instructions for left hand models 2 Door Trim Supplied handle shown in the overlay panel position e There are two sets of holes in the handle side trim Replace the handle side trim by installing the original screws in the REAR screw holes e Secure the handle to the door using the FRONT screw holes Installation Instructions STEP 10 CONNECT WATER SUPPLY FREEZER MODELS ONLY House Freezer Water Supply Water Supply e Locate and bring the tubing to the front of the cabinet e Turn the water on to flush debris from the line Run about a quart of water through the tubing into a bucket then shut off the water Copper Tubing e Slip a 1 4 nut and ferrule provided over both ends of the copper tubing Insert the tube into the union fitting on the unit and tighten the nut to the union e Turn on the water to check for leaks GE SmartConnect Tubing e Insert the molded end of the tubing into the refrigerator or freezer connection Tighten the compression nut until it is just hand tight e Tighten one additional turn with a wrench Overtightening can cause leaks e Turn o
22. lug which mates with a standard three prong grounding wall receptacle to minimize the possibility of electric shock hazard from this appliance Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded Where a standard 2 prong wall outlet is encountered it is your personal responsibility and obligation to have it replaced with a properly grounded 3 prong wall outlet HARDWARE SUPPLIED Custom handle trim Anti Tip bracket Secured to side of unit A ANNI ANN E 3 lag screws dE 2 Qe P ln 2 Hair Pin Cotters 5 toggles with bolts me 1 Toekick 4 Washers Secured to side of unit MATERIALS REQUIRED e 1 4 copper water line tubing or GE SmartConnect Refrigerator Tubing kits e Water shut off valve optional but recommended e Custom panels for door and grille panel e Screws to secure unit to cabinetry Stick on hook and loop fastener strips for 1 4 side panels FLOORING For proper installation this product must be placed on a level surface of hard material that is at the same height as the rest of the flooring This surface should be strong enough to support a fully loaded refrigerator or freezer or approximately 1 200 Ibs per unit NOTE Protect the finish of the flooring Cut a large section of the cardboard carton and place under the product where you are working NOTE Not recommended for installation
23. n the water to check for leaks NOTE Make sure excess tubing length does not interfere with the toekick installation 20 STEP 11 START ICEMAKER Power Switch Feeler Arm e Slide the switch to ON The icemaker will begin opera tion automatically e Be sure nothing interferes with the sweep of the feeler arm e Discard the first full bucket of ice cubes e To turn the icemaker off slide the switch to OFF STEP 12 INSTALL TOEKICK e Locate the supplied toekick shipped taped to the side of the product Install with 2 screws provided adjust to the desired height and tighten the screws e A custom toekick can be installed to match or complement the surrounding cabinetry Use the supplied toekick as a template to cut out the notch Supplied Toekick IMPORTANT The vented toekick must remain unobstructed for proper air circulation and operation Notes 21 Notes 22 Notes 23 31 46148 224D2601P001 06 08 JR Printed in the United States NOTE While performing installations described in this book safety glasses or goggles should be worn For Monogram local service in your area call 1 800 444 1845 NOTE Product improvement is a continuing endeavor at General Electric Therefore materials appearance and specifications are subject to change without notice GE Consumer amp Industrial Appliances General Electric Company Louisville KY 4022
24. s and professional style handles These models are shipped ready for installation Stainless Steel Wrapped Models Stainless Steel wrapped models have wrapped doors and grille panel beveled edges and tubular stainless steel handles that coordinate with other Monogram appliances These models are shipped ready for installation Trimmed Models Trimmed models are designed to be customized with decorative panels Field installed custom door and grille panels are required Framed panels You may install 1 4 thick custom panels from your cabinet manufacturer The decorative panel slides into the factory installed trim Or order black and stainless steel accessory panels from your Monogram dealer Standard Door Handle Framed Panel Standard supplied handles shown in 1 4 panel position Optional Accessory Kits e ZKHSS2 Monogram Tubular Stainless Steel handles designed to fit 3 4 overlay panels e ZKHPSS Pro Tubular Stainless Steel handle designed to fit 3 4 overlay panels e ZUG2 For side by side installation of two trimmed models This kit provides for the installation of a unified custom grille panel to span the width of two units using a framed or overlay panel e ZUGSS2 For side by side installation of two stainless steel wrapped models This kit provides a unified stainless steel grille panel to span the width of two units Overlay panels You may also choose to install custom overlay panels from your cabin
25. um total weight for assembled grille panel is 11 pounds A gt Framed Panel Dimensions Grille Panel A Width 8 Grille Height C Door Height 1 4 Framed Panel 33 7 8 8 7 8 69 5 16 Overlay Panel Dimensions A Width B Grille Height C Door Height 1 4 Backer Panel 33 7 8 8 7 8 69 5 16 0 10 Spacer Panel 32 1 2 7 5 8 67 15 16 3 4 Overlay Panel 34 1 8 g 69 9 16 3 4 OVERLAY PANEL DIMENSIONS Overlay Panel i For a more custom appearance overlay panels may be installed on trimmed models The overlay panel must Overlay rs gt Panel be secured to a 1 4 thick backer panel which slides into the trim A spacer panel 0 10 thick must be placed between the overlay and backer panel IMPORTANT NOTE Maximum total weight for assembled door panel is 67 pounds Maximum total weight for assembled grille panel is 11 pounds eC packer 4 10 Inch enter the spacer panel on the backer panel left to Panel Spacer right and top to bottom Secure the panels with glue e Center the spacer and backer panel on the overlay panel and secure with glue and screws Screws must be countersunk into the backer panel NOTE Left to right offset is not always equal to top to bottom offset Assemble the panels with glue and screws Design Guide SIDE PANELS Side panels must be used whenever the sides of the unit will be exposed The 1 4 side panels will slip into

GE Monogram Built-In All-Refrigerator/Freezer Refrigerator User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents