GE 21008 Telephone User Manual
Contents
1. Installation Instructions Pa Pre Installation Checklist Af Close the oven door to Mi Preparing the Range the broil stop position WH Remove packaging materials Any packaging materials must be removed during installation This will include adhesive tape wire ties cardboard and protective plastic Failure to remove these materials could result in damage to MH Place hands on both the appliance once the appliance has sides of the door As you been turned on and surfaces have close the door lift up and heated away from the range Open oven door and remove literature pack broiler pan and grid and oven racks Oven Racks Broiler Pan and Grid Lift door up until the hinges clear the slots Remove Installation Instructions from literature pack and read it carefully before you begin Be sure to place all literature Use and Care Installation Instruction etc in a safe place for future reference DO NOT LIFT THE DOOR BY THE HANDLE Open the oven door as NOTE The oven door is very heavy Be sure you far as it will go have a firm grip before lifting the oven door off the hinges Use caution once the door is removed Do not lay the door on its handle This could cause dents or scratches Push the hinge locks oes down toward the door Hinge JA Nyy Position frame to the unlocked WeSs position This may require a flat blade screwdriver Installation Instructions A Ins2. Remove the storage drawer The front leveling legs can be accessed from the bottom and the RAISE rear legs from the top LEG LEVELER D8 Use an adjustable wrench to adjust all four leg levelers until the range is level CAUTION The oven door is heavy You may need help lifting the door high enough to slide it into the hinges slots Do not lift the door by the handle Replacing the Oven Door De Pick the Oven Door up by placing both hands on each side The door is heavy so you may need help Do not lift the door by the handle Place the notch of the hinge arm into the bot Bottom Edge Hinge Arm tom edge of the hinge slot Hinge Notch D11 Open the oven door as far as it will open Hinge in Locked Position Push the hinge locks A up against the front Notch of Hinge Securely Fitted into Bottom of Hinge Slot frame of the oven cavity to the locked position Close the oven door Continued on following page Installation Instructions D Installing the Range com Replacing the Storage Drawer D13 Place the drawer rail on the guides D14 Push the drawer in until it stops D15 Lift the front of the drawer and push in until the stops clear the guides D16 Lower the front of the drawer and push in until it closes SPECIAL INSTRUCTIONS IF YOU HAVE PROBLEMS WHILE REPLACING THE STORAGE DRAWER IF DRAWER WON T CLOSE Drawer Does Not Close Drawer Front Panel
3. Self Cleaning Free Standing Installation Electric Range n St ru ct i O n EER2000 EER3000 JBP24 JBP26 JBP30 JBP35 JBP48 JBP64 JBP65 JBP66 JBP67 JBP70 JBP78 JBP79 JBP85 JB940 JB960 JB965 If you have questions Call 800 GE CARES or visit our website at www GEAppliances com Skill Level High Average Low Completion Time 1 to 3 Hours Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the GE Appliance Warranty See the Owners Manual for warranty information CAUTION Before you begin e NOTE TO INSTALLER Be sure to leave Read these instructions carefully and these instructions with the consumer completely e OWNER Keep these instructions for future IMPORTANT Save these instructions for reference local inspector s use e WARNING This appliance must be IMPORTANT Observe all governing codes properly grounded and ordinances Parts Included Materials Needed QA Lag Bolts Anchor Sleeves For Concrete Floors Only UL Approved 40 AMP 4 Wire Cord OR 3 Wire Cord Anti Tip Bracket and leg leveler 4 long 4 long Tools You Will Need Pa u Pencil Adjustable wrench Glasses Tane Measure 1 4 N ut driver _ Drill with Level Screwdriver Nut driver Screwdriver Pub No 31 10463 229C4053P447 3 1 Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safe
4. qualified electrician After installation have the electrician show you where your main range disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your range must be wired and fused to meet the requirements of the National Electrical Code ANSI NFPA No 70 Latest Edition You can get a copy by writing National Fire Protection Association Battery March Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requires that new but not existing construction utilize a 4 conductor connection to an electric range When installing an electric range in new construction follow the instructions in the section on NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION You must use a three wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If you connect to aluminum wiring properly installed connectors approved for use with aluminum wiring must be used Making the Electrical Connection Remove the wire cover on the back of the range by removing 5 screws using a 1 4 nut driver Do not discard these screws 5 Screws to remove wire cover Sr When reinstalling the one piece wire cover make sure that wires do not become pinched between wire cover and mainback All new constructions mobil
5. Completely Tipped Away From Power Cord May Be Body Side Obstructing Drawer Rear Drawer Support In This Area Is Resting On Top of Remove and replace making sure the power cord is not obstructing the drawer and or the rail is in the guide IF DRAWER IS CROOKED Rear Drawer Support is Drawer Front Panel On Top of Guide Rail E On the High Side li Tipped to One Side Remove and replace making sure the rail is in the guide 10 Installation Instructions Final Check List C Check to make sure the circuit breaker is closed Reset or the circuit fuses are replaced Ll Be sure power is in service to the building L Check to be sure that all packing materials and tape on metal panel if applicable under control knobs have been removed Operation Check List L Check to make sure the Clock display is energized If a series of horizontal red lines appear in the display disconnect power immediately Recheck the range wiring connections If change is made to connections retest again If no change is required have building wiring checked for proper connections and voltage It is recommended that the clock be changed if the red lines appear L Push in and turn any one of the four surface knobs to MED setting to observe that the element glows within 60 seconds Turn the knob off when glow is detected If the glow is not detected within the time limit recheck the range wiring connections If change is required re
6. Location Of Range Side Panel Eon wall Floor Wood i N 3 b in Fig 1 as Floor Wood and Wall Drill a 1 8 pilot hole through the pre marked areas Note the angle of the wall screw in Fig 2 Mount the Anti Tip bracket with the four screws provided Attachment To Wall T UUU Screw Must Enter Wood Or Metal Fig 2 INSTALLATION CONCRETE CONSTRUCTION a For concrete installation you will need two 1 4 x 1 1 2 lag screws and two sleeve anchors Locate the center of the four holes identified in Fig 1 as Floor Concrete and Wall Drill the recommended size holes in each Install the sleeve anchors into the predrilled concrete holes and install the lag and wall screws through the Anti Tip bracket Make sure the screws are securely tightened Installation Instructions D Installing the Range Storage Drawer Removal D1 Pull the drawer out until it stops D2 Lift the front of the drawer until the stops clear the guide Remove the drawer Final Check of the Anti Tip Bracket Da When installation is complete and the range is in place inspect to be sure the rear leveling leg is fully inserted into the slot of the Anti Tip Bracket Level the Range The range must be level for proper cooking and baking D5 Install the oven racks See Owners Manual for instructions D6 Put a spirit level or a glass measuring cup partially filled with water on one of the oven racks
7. e homes and installations where local codes do not allow grounding through neutral These will require a four wire flexible cord kit If the range is rated between 8 750 and 16 500 watts the cord kit must be rated for 40 amps 125 250 volts If the range is rated between 16 501 and 22 500 watts the cord kit must be rated for 50 amps 125 250 volts For existing construction a three wire flexible cord kit may be used and the same ratings apply as de scribed above When using a cord kit rated 40 Amps remove the knockout in the connection plate You must use a clamp or strain relief to hold the cord Terminations must be either closed loop terminals or open end spade lugs On some models a filter capacitor may be connected between the black and white leads on the junction block continued on following page Installation Instructions NEW CONSTRUCTION AND FOUR WIRE CORD CONNECTION KIT Complete 4 wire cord kit Below are step by step instructions on how to install the kit Screw and Ey Ground Strap Location gt Strain 4A Plate We g Remove Hyiete 3 screws pa oe oy Remove the screws on the terminal block with a 1 4 nut driver or phillips screwdriver N N Knockout in center of connection plate may be taken out Ground Remove the ground Screw screw using a 5 16 nut driver then remove and discard the ground strap Do not discard the ground screw you will need it la
8. t remove the ground strap Grounded Neutral Terminal White Push the cord upward to relieve strain while tightening the strain relief clamp B9a Re install the wire cover with the 5 B9a screws removed earlier Make sure the wires do not become pinched between the wire cover and mainback e gt 0 Special note If local codes require an undgrounded neutral you must do the following a Remove ground strap b Fasten the white wire to the center terminal c Use grounding terminal or lead to ground unit in accordance with local codes Installation Instructions Installing the Anti Tip Bracket Installing The Bracket in Wood Locating The Bracket or Concrete The anti tip bracket provided with your literature INSTALLATION WOOD CONSTRUCTION and broiler pan must be properly installed to ee ee eg prevent the range from tipping Please refer to a Locate the centers of the four holes identified the instructions provided with your anti tip bracket a Decide whether the bracket will be installed on the right or left side of range location If the bracket side of the range has an adjacent cabinet place the bracket against the back wall and cabinet as shown in Fig 1 If there is a countertop overhang offset the bracket by the amount of overhang If there is no adjacent cabinet place the bracket to the outside edge of the range side panel and back wall Adjacent Cabinet Or Final
9. tallation Required Clearances See Ilustrations below for all rough in and spacing dimensions The range may be placed with 0 clearance flush at the back wall and side walls of the cabinet r 30 MIN e fl MIN MINIMUM DIMENSIONS BETWEEN TERE COOKTOP WALLS AND ABOVE THE COOKTOP Make sure the wall covering countertop and cabinets around the range can with stand the heat up to 200 F generated by the range Allow 30 Minimum clearance between surface units and bottom of unprotected wood or metal cabinet and 15 Minimum between countertop and adjacent cabinet bottom Recommended spacing to heat sensitive surfaces Acceptable electrical outlet area Orient the electrical receptacle so the length is parallel to_the flo NOTE Use a 4 foot power cord to prevent interference with the storage drawer Power cords 4 5 or 6 foot long may have to be dressed to allow for proper drawer closing Installation Instructions Electrical Connections Electrical Requirements This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as specified on the rating plate The rating plate is located above the storage drawer on the oven frame We recommend you have the electrical wiring and hookup of your range connected by a
10. ter Install the four wire cord and strain relief through the hole in the connection plate 4 wire cord kit Connection amp Plate Strain Relief Clamp Electrical Connections on Attach the green lead below the junction block with the ground screw that was removed earlier Connect the red and black leads to the outside terminals and the white lead to the center terminal Red or gt Black Push the cord upward to relieve strain while tightening the strain relief clamp Re install the wire cover with the 5 screws removed earlier Make sure the wires do not become pinched between the wire cover and mainback Three wire connection continued on following page Installation Instructions Electrical Connections on THREE WIRE CORD CONNECTION KIT Grounded u Neutral Terminal Complete 3 wire cord kit Below are step by step instructions on t how to install Strain Connectio Relief the kit Plate Clamp Ground Strap 3 lt Ground Screw Remove the screws on the terminal block with a 1 4 nut driver or phillips screwdriver x I Remove 3 screws J 7 ey Knockout in center of connection plate may be taken out Install the three wire cord and strain relief through the hole in the connection plate Q Connection 1 amp Strain A Relief Clamp Connect the outer wires to the outside terminals and the center wire to the center terminal Do no
11. test again If no change is required have building wiring checked for proper connections and voltage 11 NOTES Pub No 31 10463 12 229C4053P447 3
12. ty WARNING For personal safety A remove house fuse or open circuit breaker before beginning installation Failure to do so could result in serious injury or even death WARNING To reduce the risk of tipping the appliance must be secured by properly installed anti tip bracket packed with the appliance All rough in and spacing dimensions must be met for safe use of your range Electricity to the range can be disconnected at the outlet without moving the range if the outlet is in the preferred location remove lower drawer To reduce the risk of burns or fire when reaching over hot surface elements cabinet storage space above the cooktop should be avoided If cabinet storage space Is to be provided above the cooktop the risk can be reduced by installing a range hood that sticks out at least 5 beyond the front of the cabinets Cabinets installed above a cooktop must be no deeper than 13 Be sure your appliance is properly installed and grounded by a qualified technician Make sure the cabinets and wall coverings around the range can withstand the temperatures up to 200 F generated by the range All ranges can tip Injury to persons could result Install anti tip bracket packed with range See Installation Instructions If you pull the range out and away from the wall for any reason make sure the Anti Tip bracket is engaged when the range is pushed back against the wall
Download Pdf Manuals
Related Search