Fusion PP-AM100010 Stereo Amplifier User Manual
Contents
1. Frequency Control 12dB Octave Low Pass crossover variable from 32Hz to 320Hz Subsonic Filter This is a variable control that filters out all sub bass frequencies below the set point at 12dB Octave OUTPUT INPUT INPUT LEVEL LPFREQ SUBSONIC BOOST REMOTE Boost Control Rear Adjust the Bass Boost to the desired level Remote Level Control Connect the Remote Level Controller using the supplied cable Power ON LED Amplifier is operational when illuminated 1 Speaker Output Connections Ensure that the speakers are connected observing correct polarity Protection LED When illuminated the amplifier is in protection mode due to any of the following fault conditions 2 Fuses Short Circuit Thermal Output Short DC Offset Ensure fuses are replaced with the same type and rating PP AM100010 Pictured Above PP AM100010 25A x 3 PP AM200010 40A x 3 PP AM300010 40A x 4 3 Power FUSION amplifiers should be connected directly to the 12V battery terminal with an inline fuse or circuit breaker as close to the battery as possible Ground When grounding earthing your amplifier ensure that the location is a good source of ground preferably the floor pan Make sure the metal is clean of paint etc as a poor earth could damage your audio system Remote Turn On This connection turns the amplifier on and should be connected to the remote turn on lead from the Head Unit If one is not availa2. x 278 W x 6O H 5ABIL x 278 W x 60 H event of an accident Power Ratings 400 Watts RMS x 1 Channel 125 Watts RMS per Channel Ensure all wiring is protected to avoid pinching or crushing which could result in 4 Ohms 1 THD N 4 Ohms 1 THD N damage to the audio system SCO Wats RMS X Flhebel 165 PRES RMS per Channel Ensure the mounting location has sufficient air flow around the amplifier If the 2 Ohms 1 THD N 2 Ohms 1 THD N i aaa g l l p i 330 Watts RMS Bridged Channels amplifier is mounted in an enclosed space a 3 fan with ducting should be used 4 Ohms 1 THD N to aid in air flow Do not mount any amplifier on a subwoofer enclosure as extended exposure to vibration may cause malfunction of the amplifier Ensure you use the recommended gauge wire cable for all amplifier PP AM60020 2Channel connections Max Power Rating 600 Watts Wiring Frequency Response 10Hz 100kHz Ensure the audio system is turned off before making any connections to the amplifier 43B L x 278 W x 80 H speakers or source unit Failure to do so could result in permanent damage to the Power Ratings 125 Watts RMS per Channel audio system 4 Ohms 1 THD N 190 Watts RMS per Channel When wiring the FUSION amplifier ensure that the cable is protected from sharp 2 Ohms 1 THD N objects and always use rubber grommets when wiring through metal panels Ensure 390 Watts RMS Bridged Channels all terminals and connections are protected
3. Flat Select for full range speakers HPF Select for mid full range speakers when using a subwoofer in the system Boost Control Adjust the Bass Boost to the desired level Power ON LED Amplifier is operational when illuminated Protection LED When illuminated the amplifier is in protection mode due to any of the following fault conditions Short Circuit Thermal Output Short DC Offset Setting the Crossover Diagram for crossover settings for 5 or larger full range speakers Diagram for crossover settings for mid full range speakers when using a subwoofer in your system Diagram for crossover settings for subwoofers NB The gray section indicates acceptable frequency ranges MONOBLOCK AMPLIFIERS Output Connectors Line level output for connection to an additional amplifier PP AM100010 PP AM200010 PP AM300010 Input Connectors Choose the correct length RCA interconnects and run them to the RCA outputs of the source unit Avoid running beside other looms and or power cable Input Level This control is used to match the input level of the amplifier to the output level of your head unit 1 Turn the amplifier level to zero 2 Turn the volume of the head unit to and the bass and treble to zero 3 Adjust the level control until the desired maximum volume is achieved without distortion a OOOO ka JC A Failure to follow these steps mav cause permanent damage to the audio svstem PP AM100010
4. POWERPLANT AMPLIFIER MANUAL PP AM300010 PP AM200010 PP AM100010 PP AM120040 PP AM60020 a CONTENTS AMPLIFIER SPECIFICATIONS AMPLIFIER INSTALLATION FOUR CHANNEL AMPLIFIER TWO CHANNEL AMPLIFIER MONOBLOCK AMPLIFIERS TROUBLESHOOTING RECORD YOUR PRODUCT DETAILS HERE MODEL NUMBER DATE OF PURCHASE AFFIX RECEIPT HERE AMPLIFIER SPECIFICATIONS ACCEPTABLE AMPLIFIER LOADS 40mm eom om PP AM300010 Monoblock PP AM200010 Monoblock YES NO Max Power Rating 3000 Watts 2000 Watts RFAMSNNOTU YES Frequency Response 20Hz 320kHz 20Hz 320kHz PP AM200010 VES 43B6 L x 278 W x 60 H 438 L x 278 W x 60 H PP AM100010 YES YES EE p 1 THDIN O4Chmel THN a 4 Ohms 1 THD N 4 Ohms 1 THD N Per Channel and Bridged Channel s Per Channel ONLY 1300 Watts RMS per Channel 900 Watts RMS x 1 Channel NB PP AM100010 IS NOT 1 Ohm STABLE 2 Ohms 1 THD N 2 Ohms 1 THD N 1500 Watts RMS x 1 Channel 1000 Watts RMS x 1 Channel 1 Ohms 1 THD N 1 Ohms 1 THD N AMPLIFIER INSTALLATION INSTALLATION WARNING LES PP AM100010 Monoblock PP AM120040 4 Channel 1 Ensure the 12V lead is disconnected from the battery before you connect any Cass AB pew equipment Max Power Rating 1000 Watts 1200 Wats 2 Ensure the mounting location will not interfere with the gas tank brake lines or electrical wiring aaa 20Hz 3EOkHz fee Ensure the Amplifier is securely fastened to the vehicle to prevent damage in the 386 L
5. ating Power FUSION amplifiers should be connected directly to the 12V battery terminal with an inline fuse or circuit breaker as close to the battery as possible Ground When grounding earthing your amplifier ensure that the location is a good source of ground preferably the floor pan Make sure the metal is clean of paint etc as a poor earth could damage your audio system Remote Turn On This connection turns the amplifier on and should be connected to the remote turn on lead from the Head Unit If one is not available a switched 12V source must be used Output Connectors Line level output for connection to an additional amplifier LPF HPF LPF HPF FLAT FLAT Input Connectors Choose the correct length RCA interconnects and run them to the RCA outputs of the source unit Avoid running beside other looms and or power cable Input Level This control is used to match the input level of the amplifier to the output level of your head unit 1 Turn the amplifier level to zero 2 Turn the volume of the head unit to and the bass and treble to zero 3 Adjust the level control until the desired maximum volume is achieved without distortion 4 Failure to follow these steps may cause permanent damage to the audio system Frequency Control 12dB Octave crossover variable from 32Hz to 320Hz For adjustment procedure see 12 Filter Selector Crossover LPF Select for subwoofer s
6. ble a switched 12V source must be used TROUBLESHOOTING PROBLEM EEA REASON CEEE Amplifier not e No 12V to No 12V to power wire wire Check fuses and connections to Check fuses and connections to battery switching on Power LED i e No power to remote e Check Remote Turn ON connection s not ON wire to head unit e Fuse broken e Replace fuse with correct tvpe and amperage Amplifier not Fuse on amplifier blown Replace fuse with correct type and working but amperage status LED ON e Amplifier too hot e Move amplifier to vented area e Turn head unit down e Speaker wires shorted e Check that there are no speaker wires shorted to another wire or to the vehicle chassis e RCA Signal e Check RCA connection to head unit e Gain control not set up e Ensure vou have set up the amplifier gain level control e Check head unit volume level e Amplifier e Check all power remote on and groundconnections e Check speakers for wire shorts PUBLISHED BY FUSION ELECTRONICS LIMITED Copyright 2008 by FUSION Electronics Limited All rights reserved Specifications and design are subject to change without notice YOU CAN HELP PROTECT THE ENVIRONMENT Please remember to respect the local regulations Hand in the non working electrical equi
7. from the vehicle chassis and from each 4 Ohms 1 THD N other as failure to do so could result in permanent damage to the audio system FOUR CHANNEL AMPLIFIER PP AM120040 FREQ FLAT k ter HPF v 32Hz 320Hz FREQ FLAT LPF HPF 32Hz 320Hz OUTPUT INPUT INPUT LEVEL FREQ FIAT BASS BOOST FIAT FREQ INPUT LEVEL INPUT uw ler ef we ET FREQ FLAT j ATE R R 3 A PROTECT N O ev foomy 32r sonz as cas tha stove 6V Boonv A k 32Hz 320Hz FRONT RHAR Speaker Output Connections Ensure that the speakers are connected observing correct polarity 2 Ohm minimum speaker impedance for stereo operation 4 Ohm minimum speaker impedance for bridged operation Fuses Ensure fuses are replaced with the same type and rating Power FUSION amplifiers should be connected directly to the 12V battery terminal with an inline fuse or circuit breaker as close to the battery as possible Ground When grounding earthing your amplifier ensure that the location is a good source of ground preferably the floor pan Make sure the metal is clean of paint etc as a poor earth could damage your audio system Remote Turn On This connection turns the amplifier ON and should be connected to the remote turn on lead from the Head Unit If one is not available a switched 12V source must be used Output Connectors Line level output for connectio
8. n to an additional amplifier Front Input Connectors Choose the correct length RCA interconnects and run them to the RCA outputs of the source unit Avoid running beside other looms and or power cable Front Input Level This control is used to match the input level of the amplifier to the output level of your source unit 1 Turn the amplifier level to zero 2 Turn the volume of the source unit to 3 4 and the bass and treble to zero 3 Adjust the level control until the desired maximum volume is achieved without distortion 4 Failure to follow these steps may cause permanent damage to the audio system Frequency Control Front X Over 12dB Octave crossover variable from 32Hz to 320Hz For adjustment procedure see 16 Filter Selector Front X Over LPF Select for subwoofer s Flat Select for full range speakers HPF Select for mid full range speakers when using a subwoofer in the system Bass Boost Control Adjust the Bass Boost to the desired level Filter Selector Rear X Over LPF Select for subwoofer s Flat Select for full range speakers HPF Select for mid full range speakers when using a subwoofer in the system Frequency Controller Rear X Over 12dB Octave crossover variable from 32Hz to 320Hz For adjustment procedure see 16 Rear Input Level This control is used to match the input level of the amplifier to the output level of your head unit 1 Turn the amplifier level to zero 2 T
9. pment to an appropriate waste disposal center ruston Specifications and design are subject to change without notice
10. urn the volume of the head unit to 3 4 and the bass and treble to zero 3 Adjust the level control until the desired maximum volume is achieved without distortion 4 Failure to follow these steps may cause permanent damage to the audio system 13 Power ON LED Amplifier is operational when illuminated 14 Protection LED When illuminated the amplifier is in protection mode due to anv of the following fault conditions Short Circuit Thermal Qutput Short DC Offset 15 Rear Input Connectors Choose the correct length RCA interconnects and run them to the RCA outputs of the source unit Avoid running beside other looms and or power cable 16 Setting the Crossover a Diagram for crossover settings for 5 or larger full range speakers b Diagram for crossover settings for mid full range speakers when using a subwoofer in your system c Diagram for crossover settings for subwoofers NB The gray section indicates acceptable frequency ranges TWO CHANNEL AMPLIFIER PP AM6OOZO FREQ r Power N v RIM GND 32Hz 320Hz PP AM6EOOZO 32Hz 320Hz b I OUTPUT INPUT INPUTLEVEL FREQ FAT BASS BOOST FREQ we yer 4 F POWER KOKO p ter o e GV omv szhzf 320z ode f cas L e e 32Hz 320Hz Speaker Output Connections Ensure that the speakers are connected observing correct polaritv Fuses Ensure fuses are replaced with the same type and r
Download Pdf Manuals
Related Search