Fujitsu D1931 Computer Hardware User Manual
Contents
1. 6 F X BIA 7 G6 x A B 8 H X X Use first PCI PCI Express slots that have a single IRQ Line no IRQ sharing If you must use another PCI PCI Express slot with IRQ sharing check whether the expansion card properly supports IRQ sharing with the other devices on this IRQ Line The drivers of all cards and components on this IRQ Line must also support IRQ sharing A26361 D1931 Z120 1 7419 Edition 1 English 25 Adding PCI cards Replacing the lithium battery In order to permanently save the system information a lithium battery is installed to provide the CMOS memory with a current A corresponding error message notifies the user when the charge is too low or the battery is empty The lithium battery must then be replaced Incorrect replacement of the lithium battery may lead to a risk of explosion The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer Do not throw lithium batteries into the household waste They must be disposed of in accordance with local regulations concerning special waste Make sure that you insert the battery the right way round The plus pole must be on the top The lithium battery holder exists in different designs that function in the same way fe gt Press th2. Equip the mainboard with the processor heat sink and memory modules before installation if possible Further information can be found in Replacing processor chapter gt Open the casing as described in the operating manual A26361 D1931 Z120 1 7419 Edition 1 English 7 Brief instructions on installing mainboard gt Should no suitable connection field be provided in the case then you must install the connection field 1 provided Ensure the plate is aligned properly so that the connections are suitable for the mainboard later gt Set the mainboard on the edge on which the connection field is located 2 and then insert the board in the case 3 Make sure that spacers in the housing are only mounted at points at which there are mounting holes in the mainboard Fasten the mainboard with the screws gt Connect the plugs for the power supply control panel and drives to the corresponding connections on the mainboard Driver installation Please refer to chapter Drivers for a description of installing drivers gt Install the drivers for the chipset You may find the driver on the Drivers amp Utilities CD Drivers 8 English A26361 D1931 Z120 1 7419 Edition 1 Interfaces and connectors The positions of the interfaces and connectors are shown on page Cover The components and connectors marked are not necessarily present on the mainboard External
3. 8 channel S PDIF v Buzzer int Speaker Support 1x LAN 1 Gbit 100 Mbit 10 Mbit vIv v LAN ASF Alert on LAN WoL Boot IvVIvV SATA ATA RAID vIv FireWire HI SPEED USB 2 0 1x Fan monitoring PSU CPU FAN1 AUX1 FAN2 AUX2 FAN3 Fan control PSU CPU FAN1 AUX1 FAN2 AUX2 v FAN3 Temperature monitoring CPU ONB1 ONB2 OFFB v SmartCard Reader Support USB serial v Fujitsu Siemens Computers Keyboard Power Button Y Support Special onboard features Silent Fan Silent Fan LT Ix System Guard Silent Drives 1x Recovery BIOS Desk Update Multi Boot Safe vivIvIv Standby HDD Password USB Security 1x Logo Boot Intel On Screen Branding 1x Internal ports DIMM Sockets DDR 400 DDR2 533 4l PCI Express x16 slot for graphics cards 1 PCI Express x1 slot 1 PCI slot 32 bit 33 MHz 5 V and 3 3 V 2 Serial ATA interface 150 Mbyte s 2 1 1 ATA interface 100 Mbyte s Floppy interface S PDIF digital Audio OUT IN Audio Input v A26361 D1931 Z120 1 7419 Edition 1 List of features English 3 List of features Internal ports continued Front panel Audio 9 pin for headphone microphone AC 97 High Definition Audio Azalia 1 FireWire 9 Pin Intel standard header USB Ports 2 0 480 MB s Serial Ports FIFO 16550 compatible Fan Connectors PSU CPU FANT AUX1 FAN2 AUX2 FAN3 S
4. As there are no drivers for processors Intel offers the possibility from the P6 family Pentium Pro on to update the command set microcode of the processor This enables minor errors to be corrected and the performance to be increased To guarantee the best possible performance and error free operation Intel recommends updating the microcode for every new processor Intel refers to the use of the processor without microcode updates as operation outside the specifications Safety for processor on Fujitsu Siemens Computers mainboards If the processor uses an old or incorrect microcode error free operation cannot be ensured Fujitsu Siemens Computers has therefore implemented a function on its mainboards that interrupts the booting process if no suitable microcode is available for the installed processor The output error message is Patch for installed CPU not loaded Please run the bios flash update diskette This message appears until the microcode update has been carried out If the computer is nevertheless operated without a microcode update error free operation is not ensured When should a microcode update be carried out A microcode update should be carried out after the installation of a new processor In contrast to the BIOS update only an updated version of the processor command set is stored The system BIOS remains unaffected by this Microcode update under DOS with bootable microcode update floppy disk brief descriptio
5. Technisches Handbuch Technical Manual Mainboard D1931 Deutsch English co FUJITSU COMPUTERS Sie haben technische Fragen oder Probleme Wenden Sie sich bitte an e Ihren zust ndigen Vertriebspartner e Ihre Verkaufsstelle Aktuelle Informationen und Updates z B BIOS Update zu unseren Mainboards finden Sie im Internet Attp www fujitsu siemens com mainboards Are there any technical problems or other questions you need clarified Please contact e your sales partner e your sales outlet The latest information and updates e g BIOS update on our mainboards can be found on the Internet under Attp www fujitsu siemens com mainboards Dieses Handbuch wurde auf Recycling Papier gedruckt This manual has been printed on recycled paper Ce manuel est imprim sur du papier recycl Este manual ha sido impreso sobre papel reciclado Questo manuale stato stampato su carta da riciclaggio Denna handbok r tryckt pa recyclingpapper Dit handboek werd op recycling papier gedrukt Herausgegeben von Published by Fujitsu Siemens Computers GmbH Bestell Nr Order No A26361 D1931 2120 1 7419 Ausgabe Edition 1 Printed in the Federal Republic of Germany AG 0504 05 04 A26361 D1931 Z120 1 7419 Mainboard D1931 Technisches Handbuch Technical Manual Ausgabe Mai 2004 May 2004 edition THEE A Intel Pentium und Celeron sind eingetragene Warenzeichen der Intel Corporation USA Microso
6. 30 32 34 36 38 40 Audio S PDIF Signal lt Q O SPDIF out GND 14 English A26361 D1931 Z120 1 7419 Edition 1 Pin assignment of internal ports Audio Input 1 H Left audio input Audio GND Right audio input Pin Power control system monitoring 1 Signal Power Guard Control PS FAN Control PS FAN Sense Audio port front not connected If the audio front panel is not used you must plug jumpers on pin pairs 5 6 and 9 10 Right line output k Right line return A26361 D1931 Z120 1 7419 Edition 1 English 15 Pin assignment of internal ports USB dual channel Chipcard reader tr elr2 ready 1tu el 12 a EEE reader on or not connected D VCC 1 or 3 VCC 20r4 5 ense ras meer T aan ors _ Daiaposivezern Fan 1 2 and 3 a EEE 4 Fan Control 16 English A26361 D1931 Z120 1 7419 Edition 1 Pin assignment of internal ports Power supply BTX ATX compatible 9 5wa 9 Sw 3 Go 8 Powergod gh asserted SV PV 9 48 V Away VEC Aux 5V VCO 12V P12VP SV VCO 12V P12VP 5V VCO C a 1 95 A26361 D1931 Z120 1 7419 Edition 1 English 17 Pin assignment of internal ports Jumper settings Your mainboard is equipped with jumpers
7. ACPI APM Power Status Status consum yt ption Normal operation On On Off Normal Simple energy G1 S1 Standby Off On flashin Almost Almost saving mode g like immediate normal ly Maximum energy S3 Off On flashin RAM ca 5s saving mode 4 g wake up Save to DRAM compone nts Maximum energy S4 Off Off Off RAM ca 20s saving mode wake up Save To Disk romper nents Soft Off G2 S5 Soft Off Off Off Off Nearly Full boot zero time Mechanically Off G3 Off Off Off Off Zero Full boot time 1 G Global status S System status 2 Two colours One colour f The power supply unit must provide sufficiently loadable 5 V standby voltage To use the WOL functionality the power supply must provide a 5 V auxiliary voltage 5VSB of at least 1 A 32 English A26361 D1931 Z120 1 7419 Edition 1 Mainboard Revision and BIOS Version Mainboard Revision and BIOS Version The compatibility e g with new processors can be independent of the BIOS version or the revision status of the mainboard used The CPU and BIOS compatibility lists are available on the Internet at www fujitsu siemens de mainboards Mainboard Revision The revision status of the mainboard exactly identifies which mainboard you have It is indicated on a sticker on the edge of the mainboard 05618476 Example Mainboard Revision BIOS version The BIOS version can be displayed in the BIOS
8. If you remove the heat sink you must clean it and apply new heat conducting paste before you remount it Please note that depending on the heat sink used different heat sink mounts are required on the mainboard gt Depending on the configuration variant you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it gt Secure the heat sink depending on the model with four screws or push it into the mounts A26361 D1931 Z120 1 7419 Edition 1 English 21 Upgrading main memory Upgrading main memory Technical data Technology DDR 333 or DDR 400 unbuffered DIMM modules Size 184 Pin 2 5 V 64 Bit no ECC 128 Mbytes to 4 Gbyte DDR 333 SDRAM 128 Mbytes to 4 Gbyte DDR 400 SDRAM Granularity 128 256 512 or 1024 Mbyte for one socket e A current list of the memory modules recommended for this mainboard is available on the Internet at www fujitsu siemens com mainboards At least one memory module must be installed Memory modules with different memory capacities can be combined A il You may only use unbuffered 2 5 V memory modules Buffered memory modules are not supported DDR DRAM memory modules must meet the PC2700 or PC3200 specification The mainboard has two memory channels channel A and channel B with two slots each slot 1 and 3 or slot 2 and 4 If you use more than one memory module then make sure to distribute the
9. Text in this bold typeface indicates the entries you make via the keyboard Text in italics indicates commands or menu items Quotation marks indicate names of chapters or terms A26361 D1931 Z120 1 7419 Edition 1 English 1 Important notes Important notes With the mainboard installed you must open the system to access the mainboard How to dismantle and reassemble the system is described in the operating manual accompanying the system Connecting cables for peripherals must be adequately shielded to avoid interference Observe the safety notes in the operating manual of your sysiem ai a xd of the lithium battery ma osion en is therefore XD observe the instructions in the Add on Be paren ihe lithium patte section Components can become very hot during operation Ensure you do not touch components when making extensions to the mainboard There is a danger of burns The shipped version of this board complies with the requirements of the EEC directive 89 336 EEC Electromagnetic compatibility Compliance was tested in a typical PC configuration When installing the board refer to the specific installation information in the manual for the receiving device replacement of expansions Information on which expansions you can use is available i The warranty is invalidated if the system is damaged during the installation or from your sales outlet or the customer service centre Information about boards To
10. The positions of the jumpers are shown on page Cover Setting via control panel plug connector Pin pair A inserted Skipping system and BIOS Setup password Pin pair B inserted System BIOS recovery Pin pair C inserted factory setting n Please pay attention on the exact position of the pin pairs Skipping system and BIOS Setup password pinpair A Pinpair A enables skipping the system and BIOS Setup password Inserted System and BIOS Setup password are skipped when the device is switched on and may be changed not inserted System and BIOS Setup password must be entered when the device is switched on Recovering System BIOS pinpair B Pinpair B enables recovery of the old system BIOS after an attempt to update has failed To restore the old BIOS you need a Flash BIOS Diskette see BIOS update chapter Inserted The System BIOS executes from floppy drive A and the inserted Flash BIOS Diskette restores the System BIOS on the mainboard not inserted Normal operation default setting 18 English A26361 D1931 Z120 1 7419 Edition 1 Add on modules Upgrading Exit energy saving mode switch off the system and remove the power plug from the mains outlet before carrying out any of the procedures described in this chapter Even when you have run down the device parts of the device e g memory modules PCI extension boards are still energised Replacing processor Technical data e Intel Penti
11. audio front panel for the front side of the system then proceed as follows gt Remove all plug in jumpers from the audio front panel connection gt Connect the cable for the audio front panel use the connections Line out and Microphone once each i If you connect audio devices on both the front and the back of the system you can only If you have connected audio devices to both Line out connections only the connection on the front of the system is active If you have connected audio devices to both Microphone connections only the connection on the back of the system is active A26361 D1931 Z120 1 7419 Edition 1 English 11 Pin assignment of internal ports Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following il Some of the following connectors may be optional Front panel Power On off Message LED Power On Watch the poling of the LEDs The positive pole Reset p LED of the connection cables is often indicated with a coloured wire Recovery Password 1 Both connector positions possiblesPeaker 2 2pin or 3pin connector possible Power On LED Indicates the system state APM or A ogether with the chapter entitled APM and ACPI system status energy saving modes see Jumper settings chapter see Jumper settings chapter 0 5 W at 8 Ohm 12 English A26361 D1931 Z120 1 7419 Edition 1 Pin assignment of internal
12. in the Main menu of the BIOS Setup nvalid NVRAM media type Switch the device off and on again If the message is still displayed please contact your sales outlet or customer service centre nvalid System Configuration Data In the Advanced menu of the BIOS Setup set the entry Reset Configuration Data to Yes nvalid System Configuration Data run configuration utility Press Fl to resume F2 to Setup This error message may be displayed if the machine was switched off during system start up Call BIOS Setup and switch to the Advanced menu Select the menu item Reset Configuration Data and change the setting to Yes Save the change and terminate BIOS Setup Reboot the device Keyboard controller error Connect another keyboard or another mouse If the message is still displayed please contact your sales outlet or customer service centre Keyboard error Check that the keyboard is connected properly Keyboard error nn nn Stuck Key Release the key on the keyboard nn is the hexadecimal code for the key A26361 D1931 Z120 1 7419 Edition 1 English 35 Error messages Missing or invalid NVRAM token Switch the device off and on again If the message is still displayed please contact your sales outlet or customer service centre Monitor type does not match CMOS RUN SETUP Correct the entry for the monitor type in the Main menu of the BIOS Setup On Board PCI VGA not configured for Bus Master In the BIOS Setup in th
13. memory modules over both memory channels By doing this you use the performance advantages of the dual channel mode The maximum system performance is given when the same memory size is used in Channel A and Channel B To simplify equipping the slots are colour coded With a memory configuration of 4 Gbytes the visible and usable main memory can be reduced down to 3 Gbytes depending on the system configuration TEE en slot 3 Channel A EEEE ot 22 English A26361 D1931 Z120 1 7419 Edition 1 Upgrading main memory Installing a memory module gt Push the holders on each side of the memory slot outwards gt Insert the memory module into the location 1 gt Atthe same time flip the lateral holders upwards until the memory module snaps in place 2 Removing a memory module gt Push the clips on the right and left of the memory slot outward 1 gt Pull the memory module out of the memory slot 2 A26361 D1931 Z120 1 7419 Edition 1 English 23 Adding PCI Express cards Adding PCI Express cards The PCI Express x16 slot is intended for graphics cards and the PCI Express x1 slot for PCI Express x1 cards Adding PCI cards Technical data 32 bit 33 MHz PCI slots 5 V and 3 3 V supply voltage 3 3 V auxiliary voltage PCI bus interrupts Selecting correct PCI slot To achieve optimum stability performance and compatibility avoid the multiple use of IRQ Lines IRQ sharing Sh
14. of a utility model or design are reserved Delivery subject to availability Right of technical modification reserved This manual was produced by cognitas Gesellschaft fur Technik Dokumentation mbH www cognitas de Ubersicht Overview Mainboard D1931 1 Diskettenlaufwerk Floppy disk drive 2 Stromversorgungs berwachung Power supply control 37 Bedienfeld Front panel 4 Stromversorgung Power supply 57 IDE Laufwerke 1 2 IDE drives 1 2 67 Serial ATA3 Serial ATA4 Serial ATA2 Serial ATA1 10 LCD Anzeige LCD Display 11 L fter 3 Fan 3 Interne Anschl sse und Steckplatze Internal connectors and slots a EH a V juueuo CE 56 E Il 12 L fter 2 Fan2 13 USB r3 14 Geh use berwachung Intrusion PCI Express x16 15 USB 110 poen xi 16 SMB Eu Bud 17 S PDIF Anschluss S PDIF mmm PCI 1 e connector 18 7 Audio Anschl sse Vorderseite Audio port front 19 Audio in 20 Zus tzliche Stromversorgung additional power supply 21 L fter 1 Fan 1 19 och Optionale Komponenten Optional components Externe Anschl sse External connectors Bedienfeld Front panel Power onoff Message LED Power On LED 2 c Mz Recovery Password 1 Both connector positions p
15. 6361 D1931 Z120 1 7419 Edition 1 Brief instructions on installing mainboard If you have purchased a separate mainboard you can install the mainboard in your system in accordance with the following brief instructions The activities described here assume a basic knowledge of PCs and cannot be carried out by a layperson If you are not sure whether you have the necessary specialised knowledge then leave this work to an expert The illustrations of the system show examples of possible cases Prior to installation gt gt Please take note of the safety information in the l Important notes chapter Check whether the processor memory modules and power supply are suitable for this mainboard processor see Replacing processor chapter memory modules see Upgrading main memory chapter power supply see Electrical Properties chapter Make sure the current requirement of the fans processor case does not exceed the loadability of the fan connections see chapter entitled Electrical Properties First only install the components absolutely necessary graphics card processor and heat sink one memory module and only connect the required connections power supply unit case connections such as ATX on off switch hard disk or floppy disk drive You should not install additional cards and devices until this minimum configuration successfully boots see chapter entitled Add on modules Upgrading Installation
16. MBus Connector Case Temperature Cover monitoring Casing open BTX 24 pin ATX12V 20 pin power supply External ports VGA Audio Mic In Line in Line out or configurable with driver 1 1 1 Audio Surround Rear Surround Center LFE S PDIF digital audio cinch OUT IN S PDIF digital audio optical OUT LAN RJ 45 PS 2 mouse keyboard FireWire 6 Pin IEEE 1394 port USB Ports 2 0 480 MB s Serial Ports RS232 FIFO 16550 compatible Parallel Port EPP ECP for use with internal devices or optional Front or Rear panel not supported by standard power supplies 4 English A26361 D1931 Z120 1 7419 Edition 1 List of features Special features Your mainboard is available in different configuration levels Depending on the configuration your mainboard is equipped with or supports the features described in the following Silent Fan LT A controller regulates the processor fan in the PC and thus prevents unnecessary noise pollution The controller operates independently of the operating system and the processor Silent Drives Hard disks and optical drives CD ROM CD RW DVD etc are besides the fans some of the greatest sources of noise in a PC The B OS Setup can be used to switch these drives into a quieter mode Recovery BIOS If an error occurs during a BIOS update e g due to a power f
17. Setup gt Press F2 during booting to open the BIOS Setup gt Press F1 The BIOS version is specified on the displayed information page under the entry BIOS Release A26361 D1931 Z120 1 7419 Edition 1 English 33 Error messages This chapter contains error messages generated by the mainboard Available CPUs do not support the same bus frequency System halted Memory type mixing detected Non Fujitsu Siemens Memory Module detected Warranty void There are more than 32 32 RDRAM devices in the system Check whether the system configuration has changed If necessary correct the settings BIOS update for installed CPU failed This message appears if the microcode update required for the connected processor is not contained in the system BIOS gt Boot the system with the inserted Flash BIOS floppy disk gt Abort the normal Flash BIOS update by answering the question about whether you want to perform the update with n 4 gt To carry out the Flash BIOS update for the processor enter flashbioL p6 Check date and time settings The system date and time are invalid Set the current date and time in the Main menu of the BIOS Setup CPU ID Ox failed Switch the server off and on again If the message is still displayed go into the BIOS setup and set the corresponding processor to Disabled in the Server CPU Status menu please contact your sales outlet or customer
18. ailure the system BIOS will be destroyed All Fujitsu Siemens Computers mainboards are equipped with a recovery BIOS With it a destroyed BIOS can easily be restored Exact instructions are provided in the chapter BIOS Recovery Recovering System BIOS DeskUpdate DeskUpdate enables simple automatic driver installation The function is available A both on the CD Drivers amp Utilities and on the Internet Desk Update Multi Boot The BIOS of the Fujitsu Siemens Computers mainboards enables booting from all 1 types mass storage devices In addition to IDE hard disks this also includes optical T drives such as CD ROM DVD and external drives that can be connected to USB or FireWire Multi Boot USB Security USB Security is a BIOS function that offers protection against unauthorised access regardless of the operating system used If USB Security is activated the system can only be started if the MemoryBird of Fujitsu Siemens Computers is connected to one a of the existing USB ports USB Security A26361 D1931 Z120 1 7419 Edition 1 English 5 List of features Safe Standby With Safe Standby the content of the main memory is saved to the hard disk when the PC switches into the Standby mode In case of an unexpected power failure the 2 content of the main memory is loaded during booting from the hard disk Additional information is available on the Internet at www fujitsu siemens com manageability 6 English A2
19. carried out directly under Windows with the DeskFlash utility DeskFlash is contained on the Drivers amp Utilities CD under DeskUpdate A26361 D1931 Z120 1 7419 Edition 1 English 27 BIOS Recovery Recovering System BIOS BIOS Recovery Recovering System BIOS i All BIOS settings are reset to the default values vvvvyv vvvvvvy Open the casing as described in the operating manual Set the switch for Restore system BIOS to ON Close the casing as described in the operating manual Insert a BIOS update floppy disk and start the PC Note the signals issued from the loudspeaker You have successfully restored the BIOS if you hear the signal sequence short short long long long and the diskette access indicator is dark This can take a few minutes Open the casing as described in the operating manual Set the switch for Restore system BIOS to OFF Close the casing as described in the operating manual Remove the floppy disk from the drive Start the PC and invoke BIOS Setup Select the menu item Reset Configuration in the menu Advanced and change the setting to Yes Save the change and terminate B OS Setup The BIOS recovery has now been completed The system restarts Drivers amp Utilities CD i Detailed information on the BIOS recovery is contained in the manual BIOS Setup 28 English A26361 D1931 Z120 1 7419 Edition 1 Microcode Update Microcode Update What is a microcode update
20. ding on the operating system used the screen resolutions in the following table refer to the mainboard screen controller If you are using an external screen controller you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller Screen resolution Refresh rate Hz Colour 640 x 480 120 32 bit 800 x 600 120 32 bit 1024 x 768 120 32 bit 1280 x 1024 120 32 bit 1600 x 1200 120 32 bit 1920 x 1440 85 32 bit 2048 x 1536 75 32 bit Internal ports and connectors The positions of the internal ports and connectors are shown on the Cover Additional information on some ports is also provided here Hard disk connection An ultra ATA 66 or ultra ATA 100 hard disk must be connected with a cable especially designed for the ultra ATA 66 or ultra ATA 100 mode gt Connect the end of the cable marked with blue to the mainboard A serial ATA 150 hard disk must be connected with a serial ATA cable gt Connect the cable to the hard disk and to the connector on the mainboard If you have connected hard disks to serial ATA one hard disk is possible per serial ATA connection you must configure the respective settings in the BIOS Setup further information you can find in the BIOS Setup manual 10 English A26361 D1931 Z120 1 7419 Edition 1 Internal ports and connectors Audio front panel If you want to use the internal connection for the
21. e Advanced menu submenu PCI Configuration set the Shared PCI Master Assignment entry to VGA One or more RDRAM devices are not used One or more RDRAM devices have bad architecture timing One or more RDRAM devices are disabled Contact your system administrator or contact our customer service centre Operating system not found Check the entries for the hard disk drive and the floppy disk drive in the Main menu and the entries for Boot Sequence submenu of the BIOS Setup Parity Check 1 Parity Check 2 Switch the device off and on again If the message is still displayed please contact your sales outlet or customer service centre Previous boot incomplete Default configuration used By pressing function key F2 you can check and correct the settings in BIOS Setup By pressing function key F1 the system starts with incomplete system configuration If the message is still displayed please contact your sales outlet or customer service centre Real time clock error Call the BIOS Setup and enter the correct time in the Main menu If the message is still displayed please contact your sales outlet or customer service centre Service Processor not properly installed The server management controller has not been correctly installed If the message is still displayed please contact your sales outlet or customer service centre Storage Extension Group xy Configuration error x Storage Extensions s found configured ar
22. e locking lug in the direction of the arrow the battery jumps somewhat out of the holder 1 gt Remove the battery 2 gt Push the new lithium battery of the identical type into the holder 3 and press it downward until it engages 4 26 English A26361 D1931 Z120 1 7419 Edition 1 BIOS update BIOS update When should a BIOS update be carried out Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems new software or new hardware In addition new BIOS functions can also be integrated A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software Where can obtain BIOS updates The BIOS updates are available on the Internet at www fujitsu siemens de mainboards How does a BIOS update work You have two ways of doing this 1 BIOS update under DOS with bootable BIOS update floppy disk brief description gt Download the update file from out website to your PC gt Insert an empty floppy disk 1 44 MB gt Run the update file e g 7931103 EXE gt A bootable update floppy disk is created Leave this floppy disk in the drive gt Restart the PC gt Follow the instructions on screen Detailed information on the BIOS update under DOS is provided in the manual on BIOS Setup Drivers amp Utilities CD 2 BIOS update under Windows with DeskFlash utility A BIOS update can also be
23. e y SE s Device List kl k2 The specified number of storage expansion units SEs in the BIOS Setup menu Server Storage Extensions Number of connected SE is incorrect Check how many SEs within the group are connected at the server and change the setting in BIOS Setup Check whether you have assigned the same device ID twice Xy Group number x Number of SEs found on the communication bus y Number of SEs entered in Number of connected SE k1 k2 Device ID of the storage extensions found 36 English A26361 D1931 Z120 1 7419 Edition 1 Error messages System battery is dead Replace and run SETUP Replace the lithium battery on the mainboard and redo the settings in the B OS Setup System Cache Error Cache disabled Switch the device off and on again If the message is still displayed please contact your sales outlet or customer service centre System CMOS checksum bad Default configuration used Call the B OS Setup and correct the previously made entries or set the default entries System Management Configuration changed or Problem occurred A system fan or system sensor has failed Check the hardware operation System timer error Switch the device off and on again If the message is still displayed please contact your sales outlet or customer service centre Uncorrectable ECC DRAM error DRAM Parity error Unknown PCI error Switch the device off and on again If the message is still displayed please c
24. eyboard Not specified Mouse Not specified VGA port Not specified 2 2000 mA USB port 1 500 mA USB port 2 500 mA USB port 3 500 mA USB port 4 500 mA 3 2000 mA USB port 5 500 mA USB port 6 500 mA USB port 7 500 mA USB port 8 500 mA The fuses on this mainboard can be used several times polyfuses Shortly after the error state has been eliminated the fuses reset to the original state Mainboard current requirement You require a Pentium4 power supply unit according to the BTX or ATX12V specification BTX 24 pin 4 pin connection ATX12V 20 pin 4 pin connection for this mainboard If you use an ATX power supply a graphics card in the PCI Express x16 slot will only be supplied with 25 W of power For high end graphics cards that require a power supply of up to 75 W a BTX power supply unit is required If you do not have a PC from Fujitsu Siemens Computer make sure that the power supply unit provides the required amperages Resource Voltage Maximum Maximum current difference BTX ATX12V power supply x5 96 2A Standby voltage of power 5 0 V 5 96 supply unit A26361 D1931 Z120 1 7419 Edition 1 English 31 APM and ACPI system status energy saving modes The specifications apply to the onboard components and represent the least favourable case In addition at least 350 mA is required for PCI on 3 3 V and 500 mA per connected device for USB on 5V APM and ACPI system status energy saving modes System status
25. ft MS MS DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation PS 2 und OS 2 Warp sind eingetragene Warenzeichen von International Business Machines Inc Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als gesch tzt anerkannt Copyright Fujitsu Siemens Computers GmbH 2004 Alle Rechte vorbehalten insbesondere auch auszugsweise die der bersetzung des Nachdrucks der Wiedergabe durch Kopieren oder ahnliche Verfahren Zuwiderhandlungen verpflichten zu Schadenersatz Alle Rechte vorbehalten insbesondere f r den Fall der Patenterteilung oder GM Eintragung Lieferm glichkeiten und technische Anderungen vorbehalten Dieses Handbuch wurde erstellt von cognitas Gesellschaft f r Technik Dokumentation mbH www cognitas de Intel Pentium and Celeron are registered trademarks of Intel Corporation USA Microsoft MS MS DOS and Windows are registered trademarks of Microsoft Corporation PS 2 and OS 2 Warp are registered trademarks of International Business Machines Inc All other trademarks referenced are trademarks or registered trademarks of their respective owners whose protected rights are acknowledged All rights including rights of translation reproduction by printing copying or similar methods even of parts are reserved Offenders will be liable for damages All rights including rights created by patent grant or registration
26. n Download the update file from out website to your PC Insert an empty floppy disk 1 44 MB Run the update file under DOS e g 931101 EXE A bootable update floppy disk is created Leave the floppy disk in the drive Restart the PC Follow the instructions on screen vvvvvy To determine whether the latest microcode update has been loaded the so called Patch ID of the processor can be read out gt Press the F1 key in the BIOS Setup The entry CPU Patch ID is shown on the displayed information page A list with the current processors and the related Patch IDs is available on the Internet If the processor is not recognised you also require the microcode update tool for processors of the P6 family A26361 D1931 Z120 1 7419 Edition 1 English 29 Drivers Drivers Only when no drivers are installed on your system or you want to update these proceed as follows gt Insert the CD Drivers amp Utilities Collection into the CD ROM drive gt Ifthe CD does not start automatically run the START EXE programme in the main directory of the CD gt Select DeskUpdate Fully automatic installation gt Follow the instructions on screen 30 English A26361 D1931 Z120 1 7419 Edition 1 Annex Electrical Properties Loadability for connections and fuses i Make sure that the connected devices do not overload the connections Fuse no Connection Maximum loadability 1 750 mA K
27. ontact your sales outlet or customer service centre Verify CPU frequency selection in Setup The frequency setting for the processor is invalid Correct the B OS Setup and the setting A26361 D1931 Z120 1 7419 Edition 1 English 37 Glossary The technical terms and abbreviations given below represent only a selection of the full list of common technical terms and abbreviations Not all technical terms and abbreviations listed here are valid for the described mainboard IAPC Instantly Available Power AC 97 Audio Codec 97 Managed Desktop PC Design ACPI Advanced Configuration and ICH VO Controller Hub Power Management Interface IDE Intelligent Drive Electronics AMR Audio Modem Riser IPSEC Internet Protocol Security AOL Alert On LAN LAN Local Area Network APM Advanced Power Management LFE Low Frequent Effects ASF Alert Standard Format LSA LAN Desk Service Agent ATA Advanced Technology MCH Memory Controller Hub Attachinent MMX MultiMedia eXtension BIOS Basic Input Output System P64H PCI64 Hub BMC iia management PCI Peripheral Component Interconnect CAN Controller Area Network PCI Peripheral Component CNR Communication Network Riser Express Interconnect Express CPU Central Processing Unit PSB Processor System Bus C RIMM Continuity Rambus Inline PSU Power Supply Unit Memory Module PXE P
28. ossiblesPeaker 2 2pin or 3pin connector possible A26361 D1931 Z120 1 7419 Umschlag Cover Contents A26361 D1931 Z120 1 7419 Edition 1 English Mainboard D1931 Your mainboard is available in different configuration levels Depending on the configuration chosen some of the hardware components described may not be available on your mainboard Additional information Information on the BIOS Setup and additional descriptions of the drivers are contained e in the readme files on your hard disk e on the driver floppy disks included e on the CD Drivers amp Utilities Collection or Drivers amp Utilities or ServerStart The programme Acrobat Reader must be installed to be able to open the manuals You will find the programme on the CD in the directory utls acrobat For more details please read the according readme txt files Notational conventions The meanings of the symbols and fonts used in this manual are as follows indicates information which is important for your health or for preventing physical damage i indicates additional information which is required to use the system properly gt Text which follows this symbol describes activities that must be performed in the order shown u This symbol indicates that you must enter a blank space press the Space Bar at this point 4 This symbol indicates that you must press the Enter key Text in this typeface indicates screen outputs
29. ould IRQ sharing be unavoidable then all involved devices and their drivers must support IRQ sharing IRQ Lines connect PCI PCI Express slots and onboard components to the interrupt controller IRQ Lines are permanently wired on the mainboard Which IRQs are assigned to the IRQ Lines is normally automatically specified by the BIOS see description in BIOS Setup Monofunctional expansions cards PCI PCI Express expansion cards require a maximum of one interrupt which is called the PCI interrupt INT A Expansion cards that do not require an interrupt can be installed in any desired slot 24 English A26361 D1931 Z120 1 7419 Edition 1 Adding PCI cards Multifunctional expansion cards or expansion cards with integrated PCI PCI bridge These expansion cards require up to four PCI interrupts INT A INT B INT C INT D How many and which of these interrupts are used is specified in the documentation provided with the card The assignment of the PCI interrupts to the IRQ Lines is shown in the following table Controller or slot INT Mechanical slot On board controller 1 2 3 4 ies AC97 PA USB 1 1 HD PCI slot INT o u Audio ej LINE E 5 z x x mm o I o 2 2553 752 4st and 3rd 4th 8 2 a 1 2 3 a 1 a I 1 A X A B 2 B X IBIC 3 C X DIDI C 4 D E x A C DY 5 E s x g E
30. ports m 5m m Sw GND 2 3 Smdwigs 4 Ke key 8 o Powerom EDs e Speaker 9 Power on teo o Reeva Power On LED 12 Reserved Stand by LED GND Key SCSI LED Input low asserted Power Button low asserted Serial ATA 1 Transmit data positive Transmit data negative Receive data negative Receive data positive Key A26361 D1931 Z120 1 7419 Edition 1 English 13 Pin assignment of internal ports ATA interface 2 Reset drive low asserted Data 7 high asserted Data 6 high asserted 6 Data 5 high asserted 8 Data 10 high asserted 12 14 16 Signal GND Data 8 high asserted Data 9 high asserted i Data 11 high asserted Data 4 high asserted Data 3 high asserted Data 12 high asserted Data 2 high asserted Data 13 high asserted Data 1 high asserted Data 14 high asserted Data 0 high asserted 18 Data 15 high asserted N o GND 20 Key DRQ high asserted GND GND 22 24 lOread lowassered 26 WO ready low asserted 28 Cable select DAK low asserted 30 GND 32 a 36 38 I O write low asserted GND ADR 2 high asserted CS 3 low asserted IDE LED low asserted 40 GND not connected ATA66 Detect low asserted in 2 4 10 12 14 16 18 22 24 26 28
31. ports The positions of the external ports are shown on page Cover PS 2 keyboard port purple Audio input Line in light blue JOlO Serial interface turquoise i PS 2 mouse port green CJ Monitor poit blue Parallel port Printer burgundy L LAN LAN connector optional he gt USB Universal Serial Bus black su k 3 Audio output Line out light green A Micraphon jack morio pink LAN connector The mainboard is optionally equipped with the Broadcom BCM5751 LAN controller This LAN controller supports the transfer rates 10 Mbit s 100 Mbit s and 1000 Mbit s The LAN controller supports the WOL functionality through Magic Packet It is also possible to boot a device without its own boot hard disk via LAN Here bootix amp BootP and Intel PXE are supported The LAN RJ45 connector has two LEDs light emitting diodes 1 T amp m 2 LED 1 lights green a connection exists e g to a hub LED is blinking green activity LED 2 lights up differently depending on the transfer rate 10 Mbit s off 100 Mbit s green 1000 Mbit s yellow A26361 D1931 Z120 1 7419 Edition 1 English 9 Internal ports and connectors Graphics port Technical data Function 2D 3D graphics controller Dynamic Video memory Technology 400 Mhz integrated 24 bit RAMDAC Features Display Data Channel DDC 2 DVO channels up to 165 megapixels per channel dual view support for ADD2 boards Screen resolution Depen
32. prevent damage to the mainboard the components and conductors on it please take great care when you insert or remove boards Take great care to ensure that extension boards are slotted in straight without damaging components or conductors on the mainboard or any other components for example EMI spring contacts Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage Be careful with the locking mechanisms catches centring pins etc when you replace the mainboard or components on it for example memory modules or processors Never use sharp objects screwdrivers for leverage Boards with electrostatic sensitive devices ESD are identifiable by the label shown A When you handle boards fitted with ESDs you must under all circumstances 4 observe the following Ate e You must always discharge static build up e g by touching a grounded object before working e e The equipment and tools you use must be free of static charges e Remove the power plug from the mains supply before inserting or removing boards containing ESDs e Always hold boards with ESDs by their edges e Never touch pins or conductors on boards fitted with ESDs 2 English A26361 D1931 Z120 1 7419 Edition 1 List of features Onboard features o A Chipset Intel 915G Board size uATX VGA Y Audio
33. reboot eXecution Environment DIMM Dual Inline Memory Module RAID Redundant Array of ECC Error Correcting Code Independent Disks ECP Enhanced Capability Port RAM Random Access Memory EEPROM Electrical Erasable RAMDAC Random Access Memory Programmable Read Only Digital Analogue Converter Memory RDRAM Rambus Dynamic Random EPP Enhanced Parallel Port Access Memory FDC Floppy disk controller RTC Real Time Clock FIFO First In First Out S PDIF Sony Philips Digital Interface FSB Front Side Bus SATA Serial Advanced Technology FWH Firmware Hub usn Dua GMCH Graphics and Memory SB Soundblaster Controller Hub SDRAM Synchronous Dynamic Random GPA Graphics Performance Access Memory Accelerator SGRAM Synchronous Graphic Random HDD Hard Disk Drive Access Memory PC Inter Integrated Circuit SIMD Streaming Mode Instruction 38 English Single Instruction Multiple A26361 D1931 Z120 1 7419 Edition 1 Data SMBus System Management Bus SVGA Super Video Graphic Adapter TEMP Temperature USB Video Graphic Adapter USB Universal Serial Bus VGA Video Graphic Adapter WOL Wake On LAN A26361 D1931 Z120 1 7419 Edition 1 Glossary English 39
34. service centre CPU mismatch detected You have replaced the processor or changed the frequency setting As a result the characteristic data of the processor have changed Confirm this change by running the BIOS Setup and exiting it again Diskette drive A error Diskette drive B error Check the entry for the diskette drive in the Main menu of the BIOS Setup Check the connections to the diskette drive 34 English A26361 D1931 Z120 1 7419 Edition 1 Error messages DMA test failed EISA CMOS not writable Extended RAM Failed at offset nnnn Extended RAM Failed at address line nnnn Failing Bits nnnn Fail Safe Timer NMI failed Multiple bit ECC error occurred Memory decreased in size Memory size found by POST differed from EISA CMOS Single bit ECC error occurred Software NMI failed System memory exceeds the CPU s caching limit System RAM Failed at offset nnnn Shadow RAM Failed at offset nnnn Switch the device off and on again If the message is still displayed please contact your sales outlet or customer service centre Failure Fixed Disk 0 Failure Fixed Disk 1 Fixed Disk Controller Failure Check the entry for the hard disk drive in the Main menu and the entry for the IDE drive controller in the Advanced Peripheral Configuration menu of the BIOS Setup Check the hard disk drive s connections and jumpers ncorrect Drive A run SETUP ncorrect Drive B run SETUP Correct the entry for the diskette drive
35. um 4 with 533 or 800 MHz front side bus in the LGA775 design e Celeron with 800 MHz Front Side Bus in the LGA775 design e A current list of the processors supported by this mainboard is available on the Internet at www fujitsu siemens com mainboards Installing processor with heat sink Never touch the underside of the processor Even minor soiling such as grease from the skin can impair the processor s operation or destroy the processor Place the processor in the socket with extreme care as the spring contacts of the socket are very delicate and must not be bent gt Remove the heat sink gt Press down the lever 1 and unhook it gt Fold up the frame A26361 D1931 Z120 1 7419 Edition 1 English 19 Replacing processor gt Remove the old processor 2 from the socket gt Insert the new processor in the socket so that the marking of the processor is aligned with the marking on the socket a gt Fold down the frame 1 gt Press the lever downward 2 until it is hooked in again 3 20 English A26361 D1931 Z120 1 7419 Edition 1 Replacing processor Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink If a heat conducting pad rubber like foil is already applied to the heat sink then use it Otherwise you must apply a very thin layer of heat conducting paste Heat conducting pads can only be used once
Download Pdf Manuals
Related Search