FujiFilm 16309733-3-KIT Digital Camera User Manual
Contents
1. E RA WWW truemfg com n o 17 7 IE LLE True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING STAINLESS STEEL EQUIPMENT CARE AND CLEANING CAUTION Do not use any steel wool abrasive or chlorine based products to clean stainless steel surfaces Stainless Steel Opponents D 2 3 There are three basic things which can break down your stainless steel s passivity layer and allow corrosion to rear its ugly head Scratches from wire brushes scrapers and steel pads are just a few examples of items that can be abrasive to stainless steel s surface Deposits left on your stainless steel can leave spots You may have hard or soft water depending on what part of the country you live in Hard water can leave spots Hard water that is heated can leave deposits if left to sit too long These deposits can cause the passive layer to break down and rust your stainless steel All deposits left from food prep or service should be removed as soon as possible Chlorides are present in table salt food and water Household and industrial cleaners are the worst type of chlorides to use 8 steps that can help prevent rust on stainless steel 1 18 Using the correct cleaning tools Use non abrasive tools when cleaning your stainless steel products The stainless steel s passive layer will not be harmed by soft cloths and plastic scouring pads Step 2 tells you how2. Product Loss and Lost Sales Proper cleaning involves removing dust from the Condenser By using a soft brush or vacuuming the Condenser with a shop vac or using C02 nitrogen or pressurized air If you cannot remove the dirt adequately please call your refrigeration service company On most of the reach in units the condenser is accessible in the rear of the unit You must remove the cabinet grill to expose the Condenser The Condenser looks like a group of vertical fins You need to be able to see through the condenser for the unit to function at maximum capacity Do not place filter material in front of condensing coil This material blocks air flow to the coil similar to having a dirty coil HOW TO CLEAN THE CONDENSER 1 Disconnect the electrical power to the unit 2 Remove the louvered grill Sg Unit 3 Vacuum or brush the dirt lint or debris from the finned condenser coil Condenser 4 If you have a significant dirt build up you can blow out the condenser with compressed air CAUTION MUST BE USED to avoid eye injury Eye protection is recommended 5 When finished be sure to replace the louvered grill The gill protects the condenser 6 Reconnect the electrical power to the unit If you have any questions please call True Manufacturing at 636 240 2400 or 800 325 6152 and ask for the Service Department Service Department Availability Monday Friday 7 30 a m to 5 30 p m and Saturday 7 45 a m to 11 45 a m CST
3. When using chlorinated cleaners you must rinse and wipe dry immediately It is better to wipe standing cleaning agents and water as soon as possible Allow the stainless steel equipment to air dry Oxygen helps maintain the passivity film on stainless steel Hydrochloric acid muriatic acid should never be used on stainless steel Regularly restore passivate stainless steel Ser WWW truemfg com o n 18 True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING STAINLESS STEEL EQUIPMENT CARE AND CLEANING 19 Recommended cleaners for certain situations environments of stainless steel A Soap ammonia and detergent medallion applied with a cloth or sponge can be used for routine cleaning B Arcal 20 Lac O Nu Ecoshine applied provides barrier film for fingerprints and smears C Cameo Talc Zud First Impression is applied by rubbing in the direction of the polished lines for stubborn stains and discoloring D Easy off and De Grease It oven aid are excellent for removals on all finishes for grease fatty acids blood and burnt on foods E Any good commercial detergent can be applied with a sponge or cloth to remove grease and oil F Benefit Super Sheen Sheila Shine are good for restoration passivation NOTE The use of stainless steel cleaners or other such solvents is not recommended on plastic parts Warm soap and water will suffice Drue 19 7 TL LLE True Food Service Equipment Inc INSTAL
4. personal responsibility and obligation to have it cord replaced with the properly grounded 3 prong wall outlet The refrigerator should always be plugged into its own individual electrical circuit which has a voltage rating that matches the rating plate This provides the best performance and also prevents overloading building wiring circuits which could cause a fire hazard from overheated wires USE OF ADAPTER PLUGS NEVER USE AN ADAPTER PLUG Because of potential safety hazards under certain conditions we strongly recommend against the use of an adapter plug North America Use Only NEMA plugs TRUE uses these types of plugs If you do not have the right outlet have a certified electrician install the correct power source 115 60 1 NEMA 5 15R Drue True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS INSTALLATION OPERATION INSTRUCTIONS OWNERSHIP To insure that your unit works properly from the first day it must be installed properly We highly recommend a trained refrigeration mechanic and electrician install your True equipment The cost of a professional installation is money well spent REQUIRED TOOLS Before you start to install your True unit carefully inspect it for freight damage If damage is discovered immediately file a claim with the delivery freight carrier True is not responsible for damage incurred during shipment e Adjustable Wrench e Phillips Head S
5. and bottom holes bottom peg first front holes are taped over to improve insulation values Remove divider from the front holes and line up regular and spring loaded rear pegs with holes in line with those desired in front Insert as far as possible and maneuver front pegs in place SHELF INSTALLATION FOMTTATAAALDALA ALLDATA LAAN AAA AAA AN l Shelf Standards FVTTTTTTTTTTAT OUTTA ATTA AAA ATT OTA AT Gane oor a Geor Toma omit Pillaster I beam BIN DIVIDER INSTALLATION cere g Divider positioned a in front of i Q mechanical box soont aaa o o ooo STORAGE AND HANDLING Draft beer should be treated as a food product In most instances draft beer is not pasteurized It is very important that you store and handle it properly Follow these steps to ensure the highest quality and consumer satisfaction e Draft beer should be immediately stored in a refrigerated cabinet e Draft beer products have a recommended shelf life If you have questions regarding the shelf life of any of your draught products please consult with your supplying depot or respective Brewer representative e Kegs should be stored separately from food products If your cooler is used to refrigerate draught and food products it is very important that the f
6. mA a 1 line cleaning powder Spanner Brush wrench Pump bottle and tub Bucket and fresh water 4 Rinse parts Thoroughly a Fill pump bottle with DBK solution 6 Attach hose from pump bottle to beer column tap outlet be sure rubber gasket is in place to prevent leakage allow tap to drain in bucket fig 3 7 Pump solution 2 3 times from bottle through the line until it starts to flow out the beer line Wait 10 minutes while cleaning solution works on the lines 8 Pump excess solution through lines 9 Rinse bucket pump bottle and hose thoroughly with clean cool water 70 Fill pump bottle with clean cool water and pump through lines until water runs clear 11 When crystal clear water comes through you re ready to assemble and reattach faucet and re tap the barrel 12 Draw the water from the beer line now you re ready to serve brewery fresh golden beer NOTE Keeping your dispenser and all its parts clean and odor free will help you to serve beautiful foam topped glasses of delicious satisfying draught beer fo O O WWW truemfg com n o 15 Drue True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING MAINTENANCE CARE amp CLEANING CLEANING THE CONDENSER COIL When using electrical appliances basic safety precautions should be followed including the following REQUIRED TOOLS Phillips Screwdriver e Stiff Bristle Brush e Adjustable W
7. 4 14 12 12 12 10 10 10 8 16 14 14 14 14 12 12 12 10 10 10 8 8 18 14 14 14 12 12 12 10 10 10 8 8 8 20 14 14 14 12 10 10 10 10 10 8 8 8 25 14 14 12 12 10 10 10 10 8 8 6 6 30 14 12 12 10 10 10 8 8 8 6 6 6 35 14 12 10 10 10 8 8 8 8 6 6 5 40 14 12 10 10 8 8 8 6 6 6 5 5 50 12 10 10 8 6 6 6 6 6 5 4 4 60 12 10 8 6 6 6 6 6 5 4 4 3 70 10 10 8 6 6 6 5 5 4 4 2 2 80 10 8 8 6 6 5 5 4 4 3 2 2 90 10 8 6 6 5 5 4 4 3 3 1 1 100 10 8 6 6 5 4 4 3 3 2 1 1 True Food Service Equipment Inc Drue INSTALLATION OPERATION INSTRUCTIONS SEALING CABINET TO FLOOR Step 1 Position Cabinet Allow one inch between the wall and rear of the refrigerated Bar Equipment to assure proper ventilation For Glass amp Plate Chillers Frosters 3 inches between the wall and rear of the cabinet will assure proper ventilation Step 2 Level Cabinet Cabinet should be level side to side and front to back Place a carpenter s level in the interior floor in four places A Position level in the inside floor of the unit near the doors Level should be parallel to cabinet front Level cabinet B Position level at the inside rear of cabinet Again level should be placed parallel to cabinet back C Perform similar procedures to steps A amp B by placing the level on inside floor left and right sides parallel to the depth of the cooler Level cabinet Step 3 Draw an outline on the base on the floor Step 4 Raise and block the front side of the cab
8. C and simultaneously turn regulator key counter clockwise to zero reading Close regulator shut off C and set pressure by turning regulator key clockwise Check setting by opening and closing valve C Close tap head D put in OFF position Tap barrel at D and open regulator shut off C 14 Drue True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING CLEANING BAR SYSTEM Draught dispensers regardless of design must be cleaned at least every two weeks Flushing your draught dispenser with water only is not enough Note Use cleaners approved by your beer supplier and follow their instructions If you are using the cleaning kit purchased from True follow these instructions Exacting cleanliness should be constantly maintained in your dispenser so that your draught beer will be at its best when served Although the beer in the barrel is in excellent condition it can become less satisfying as it is drawn through the beer line and faucet if they are not kept clean Prepare Solution e Add 1 2 ounce 19 grams of line cleaning powder to each quart of water cold or warm Cleaning 1 Disconnect tap from barrel Remove beer faucet with spanner wrench unscrew handle and remove valve assembly fig 1 2 Put tap and faucet parts in a bucket with cleaning solution to soak 3 Use small brush to clean beer faucet parts fig 2 Beer Tap Cleaning Kit Required Tools
9. LATION OPERATION INSTRUCTIONS LIGHT BULB REPLACEMENT IDL INTEGRATED DOOR LIGHTING Be careful when removing the light bulb WARNING Please be aware of your local ordinances in When replacing a light bulb make sure disposing old florescent bulbs These bulbs power to the unit is either turned off or should be disposed in a safe and correct unplugged manner Remove the lampshield to reveal the bulb Squeeze the sides of the lampshield at the same time pulling it away from the bulb The lamp holders are spring activated Pull the top lamp holder up and push the bulb down at the same time This will leave enough clearance to remove the bulb 20 OOOO ODRO www truemfg com o n 20 TRUE REFRIGERATION True Food Service Equipment Inc MADE IN U S A WARRANTY INFORMATION U S A and Canada ONLY SINCE 1945 ONE YEAR PARTS amp LABOR WARRANTY TRUE warrants to the original purchaser of every new TRUE refrigerated unit the cabinet and all parts thereof to be free from defects in material or workmanship under normal and proper use and maintenance service as specified by TRUE and upon proper installation and start up in accordance with the instruction packet supplied with each TRUE unit TRUE s obligation under this warranty is limited to a period of one 1 year from the date of original installation or 15 months after shipment date from TRUE whichever occurs first Any part covered under this warranty that are d
10. NLY TERMS Cut out Temperature sensed by the controller that shuts the compressor off Cut in Temperature sensed by the controller that turns the compressor on REQUIRED TOOLS Phillips Head Screwdriver e 5 64 or 2 mm Allen Wrench e T 7 Torx Wrench STEP 1 Unplug the cooler STEP 2 Remove the screws that secure the temperature control to the inset box STEP 3 Pull out gently from cabinet NOTE Mechanical temperature controllers are affected when functioning at high altitude The cut in and cut out temperatures will be colder than when the controller functions closer to sea level 13 STEP 4 For high elevation installations it may be necessary to warm up the set points To make the adjustment insert the appropriate tool in each adjustment screw and turn 1 4 of a revolution clockwise to the right This procedure will adjust both the cut in and cut out about 2 F warmer STEP 5 Make sure to reconnect the pink wire to the proper spade terminal when reinstalling Danfoss Temperature Control High Altitude Adjustment Only Cut out Adjustment Screw Allen 5 64 or 2 mm clockwise for warmer Cut in Adjustment Screw Torx T 7 clockwise for warmer Compressor Connection pink Compressor Connection pink 13 Drue True Food Service Equipment Inc MAINTENANCE CARE amp CLEANING CHANGING CO2 GAS CYLINDER Decreasing Pressure Follow these instr
11. NOT COVERED BY THIS WARRANTY TRUE s sole obligation under this warranty is limited to either repair or replacement of parts subject to the additional limitations below This warranty neither assumes nor authorizes any person to assume obligations other than those expressly covered by this warranty NO CONSEQUENTIAL DAMAGES TRUE IS NOT RESPONSIBLE FOR ECONOMIC LOSS PROFIT LOSS OR SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION LOSSES OR DAMAGES ARISING FROM FOOD OR PRODUCT SPOILAGE CLAIMS WHETHER OR NOT ON ACCOUNT OF REFRIGERATION FAILURE WARRANTY IS NOT TRANSFERABLE This warranty is not assignable and applies only in favor of the original purchaser user to whom delivered ANY SUCH ASSIGNMENT OR TRANSFER SHALL VOID THE WARRANTIES HEREIN MADE AND SHALL VOID ALL WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IMPROPER USAGE TRUE ASSUMES NO LIABILITY FOR PARTS OR LABOR COVERAGE FOR COMPONENT FAILURE OR OTHER DAMAGES RESULTING FROM IMPROPER USAGE OR INSTALLATION OR FAILURE TO CLEAN AND OR MAINTAIN PRODUCT AS SET FORTH IN THE WARRANTY PACKET PROVIDED WITH THE UNIT ALTERATION NEGLECT ABUSE MISUSE ACCIDENT DAMAGE DURING TRANSIT OR INSTALLATION FIRE FLOOD ACTS OF GOD TRUE is not responsible for the repair or replacement of any parts that TRUE determines have been subjected after the date of manufacture to alteration neglect abuse misuse accident damage d
12. SPENSERS On beer dispensers the drain is located at the front of the cabinet To plumb in the drain connect 2cm PV C pipe to the 2cm barbed fitting supplies with the unit CO5 PRESSURE Mobile tapsters to retain complete mobility the CO tank up to five pounds in size can be placed inside the cooler strap holders furnished Beer line connector beer draft arm handle onto the draft arm WARNING Compressor warranties are void if compressor burns out due to low voltage WARNING Power supply cord ground should not be removed NOTE To reference wiring diagram Remove front louvered grill wiring diagram is positioned on the inside cabinet wall CAUTION Filled CO tanks are potentially dangerous because of the pressure they contain If you are unfamiliar with their use or the use of the CO regulator seek information from your local distributor or your local beverage man before proceeding INSTALL DRAFT ARM Place rubber washer over draft arm mounting holes in cabinet put beer line connector down through hole Next secure draft arm with four screws See images 1 6 arm to cabinet with rubber gasket under the draft arm CONTINUED ON NEXT PAGE True Food Service Equipment Inc Drue INSTALLATION OPERATION INSTRUCTIONS BEER DISPENSERS CONTINUED INSTALL DRAFT ARM continued Insert air hose one inch plastic tube in draft arm being careful not to disturb insula
13. TRUE FOOD SERVICE EQUIPMENT INC 2001 East Terra Lane P O Box 970 O Fallon Missouri 63366 D 636 240 2400 FAX 636 272 2408 INT L FAX 636 272 7546 800 325 6152 Parts Department 800 424 TRUE Parts Department FAX 636 272 9471 INSTALLATION MANUAL FOR BAR EQUIPMENT AND GLASS CHILLERS TDD 4 TABLE OF CONTENTS gt Safety Information Safety Precautions 1 Proper Disposal 2 Connecting Electricity 3 Adapter Plugs 3 gt Installation Operation Instructions Ownership 4 Required Tools 4 TD 50 18 S LT Uncrating 4 Location 5 Leveling Cabinet 5 Wire Gauge Cart 6 Sealing Cabinet to the floor 7 Electrical Instructions 8 Beer Dispensers 8 9 Start up and Light Switch Location 9 Shelving amp Bin Divider Installation 10 Storage amp Handling 10 Temperature Pressure Tapping 11 Draft Beer Problems __ 12 gt Maintenance Care amp Cleaning Temperature Control Adjustment 13 Changing CO Gas Cylinder _ 14 Cleaning Bar System _ _ 15 Cleaning the Condenser _ 16 Important Warranty Information 17 Stainless Steel Equipment Care amp Cleaning 18 19 TBB 3G S Lightbulb Replacement 20 Warranty U S A and Canada ONLY 21 Spanish German Fr
14. are throwing away your old refrigerator make sure the refrigerant is removed for proper disposal by a qualified service technician If you intentionally release any refrigerants you can be subject to fines and imprisonment under provisions of the environmental regulations USE OF EXTENSION CORDS NEVER USE AN EXTENSION CORD TRUE will not warranty any refrigerator that has been connected to an extension cord True Food Service Equipment Inc 7 TE LLE SAFETY INFORMATION WARNING HOW TO CONNECT ELECTRICITY Do not under any circumstances cut or remove the third ground prong from the power cord For personal safety this appliance must be properly grounded The power cord of this appliance is equipped Never unplug your refrigerator by pulling on the with a 3 prong grounding plug which mates power cord Always grip plug firmly and pull with a standard 3 prong grounding wall outlet to straight out from the outlet minimize the possibility of electric shock hazard Repair or replace immediately all power cords that from this appliance have become frayed or otherwise damaged Do not Have the wall outlet and circuit checked by a use a cord that shows cracks or abrasion damage qualified electrician to make sure the outlet is along its length or at either end properly grounded When removing the refrigerator away from the wall If the outlet is a standard 2 prong outlet it is your be careful not to roll over or damage the power
15. b stand or hang e Unplug the refrigerator before cleaning and on the shelves in the refrigerator They could making repairs damage the refrigerator and seriously injure Setting temperature controls to the 0 position themselves does not remove power to the light circuit Do not touch the cold surfaces in the freezer perimeter heaters or evaporator fans compartment when hands are damp or wet Skin may stick to these extremely cold surfaces e Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance e Keep fingers out of the pinch point areas clearances between the doors and between the doors and cabinet are necessarily small be careful closing doors when children are in the area True Food Service Equipment Inc SAFETY INFORMATION DANGER RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE REFRIGERATOR Child entrapment and suffocation are not problems of the past Junked or abandoned refrigerators are still dangerous even if they will sit for just a few days If you are getting rid of your old refrigerator please follow the instructions below to help prevent accidents Before You Throw Away Your Old Refrigerator or Freezer e Take off the doors e Leave the shelves in place so that children may not easily climb inside Refrigerant Disposal Your old refrigerator may have a cooling system that uses Ozone Depleting chemicals If you
16. crewdriver e Level UNCRATING Step 1 The following procedure is recommended for uncrating the unit A Remove the outer packaging cardboard and bubbles or styrofoam corners and clear plastic Inspect for concealed damage Again immediately file a claim with the freight carrier if there is damage B Move your unit as close to the final location as possible before removing the wooden skid C Remove door bracket on swinging glass door models see image 1 2 Note Keys for coolers with door locks are located in warranty packets REMOTE UNITS This section applies to remotes only e Remote cabinets must be ordered as remote We do not recommend converting for a standard self contained to remote system e All remote cabinets must be hard wired e No castors available e All remote cabinets come standard using 404A refrigerant e All remote units come standard with expansion valve liquid line solenoid heated condensate pan and defrost timer when applicable e Contact True Technical Service for BTU requirements e No wiring necessary between cabinet and condensing unit e All remote condensing units purchased from True are 208 230 volts single phase If you have any questions regarding this section please call True at 1 800 325 6152 Mees fate WWW trUueMfZ COM n o 4 True Food Service Equipment Inc Drue INSTALLATION OPERATION INSTRUCTIONS LOCATING TOOLS REQUIRED Philli
17. ench and Dutch versions included CONGRATULATIONS You have just purchased the finest commercial refrigerator available You can expect many years of trouble free operation TDB 24 48 1 G 1 BAR EQUIPMENT AND GLASS CHILLERS 9 8 08 18K SB 894417 7 IL LLE True Food Service Equipment Inc NOTICE TO CUSTOMER Loss Or Spoilage Of Products In Your Refrigerator Freezer Is NOT Covered By Warranty In Addition To Following Recommended Installation Procedures You Must Run The Refrigerator Freezer 24 Hours Prior To Usage True Manufacturing Company Inc True Food Service Equipment Inc 7 IE LLE SAFETY INFORMATION How to Maintain Your LLLE Unit to Receive the Most Efficient and Successful Operation You have selected one of the finest commercial refrigeration units made It is manufactured under strict quality controls with only the best quality materials available Your TRUE cooler when properly maintained will give you many years of trouble free service WARNING Use this appliance for its intended purpose as described in this Owner Manual SAFETY PRECAUTIONS When using electrical appliances basic safety precautions should be followed including the following e This refrigerator must be properly installed NOTE We strongly recommend that any and located in accordance with the Installation servicing be preformed by a qualified Instructions before it is used individual Do not allow children to clim
18. essure regulator e Obstruction in lines False Head Description Large soap like bubbles head dissolves very quickly e Dry glasses e Improper pour e Pressure required does not correspond to beer temperature e Coils or direct draw beer lines warmer than beer in keg e Small lines into large faucet shanks e Beer drawn improperly Wild Beer Description Beer when drawn is all foam and not enough liquid beer e Beer drawn improperly e Faucet in bad or worn condition e Kinks dents twists or other obstructions in line e Traps in beer lines e Beer too warm in kegs or lines Too much pressure e Creeping gauge causing too much pressure Cloudy Beer Description Beer in the glass appears hazy Not clear e Dirty glass or faucet e Beer over chilled e Beer temperature variance in keg Beer may have warmed up at sometime Hot spots in beer lines e Cutting beer through faucet e Beer line in poor condition e Dirty lines e Beer that has been frozen Bad Taste e Dirty faucet e Old or dirty beer lines e Failure to flush beer lines with water after each empty keg e Unsanitary conditions at bar e Foul air or dirt in lines e Oily air greasy kitchen air e Temperature of package too warm e Dry glasses Ie etc WWW truemfg com n o 12 True Food Service Equipment Inc Drue MAINTENANCE CARE amp CLEANING TEMPERATURE CONTROL ADJUSTMENT FOR HIGH ALTITUDE O
19. etermined by TRUE to have been defective within one 1 year of original installation or fifteen 15 months after shioment date from manufacturer whichever occurs first is limited to the repair or replacement including labor charges of defective parts or assemblies The labor warranty shall include standard straight time labor charges only and reasonable travel time as determined by TRUE ADDITIONAL FOUR YEAR COMPRESSOR WARRANTY In addition to the one 1 year warranty stated above TRUE warrants its hermetically and semi hermetically sealed compressor to be free from defects in both material and workmanship under normal and proper use and maintenance service for a period of four 4 additional years from the date of original installation but not to exceed five 5 years and three 3 months after shipment from the manufacturer Compressors determined by TRUE to have been defective within this extended time period will at TRUE s option be either repaired or replaced with a compressor or compressor parts of similar design and capacity The four 4 year extended compressor warranty applies only to hermetically and semi hermetically sealed parts of the compressor and does not apply to any other parts or components including but not limited to cabinet paint finish temperature control refrigerant metering device driers motor starting equipment fan assembly or any other electrical component etcetera 404A 134A COMPRESSOR WARRANTY The fou
20. inet Step 5 Apply a bead of NSF Approved Sealant see list below to floor on half inch inside the outline drawn The bead must be heavy enough to seal the entire cabinet surface when it is down on the sealant Step 6 Raise and block the rear of the cabinet Step 7 Apply sealant on floor as outlined in Step 5 on other three sides Step 8 Examine to see that cabinet is sealed to floor around entire perimeter Note Asphalt floors are very susceptible to chemical attack A layer of tape on the floor prior to applying the sealant will protect the floor NSF Approved Sealants Minnesota Mining ECU800 Caulk Minnesota Mining ECU2185 Caulk Minnesota Mining ECU1055 Bead Minnesota Mining ECU1202 Bead Armstrong Cork Rubber Caulk Products Research Co 5000 Rubber Caulk GE Silicone Sealer O N A Mm KR WN e Dow Corning Silicone Sealer DrLe True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS ELECTRICAL INSTRUCTIONS Step 4 A Before your new unit is connected to a power supply check the incoming voltage with a voltmeter If anything less than 100 of the rated voltage for operation is noted correct immediately B All units are equipped with a 7 ft 2 1m service cord and must be powered at proper operating voltage at all times Refer to cabinet data plate for this voltage True recommends that a sole use circuit be dedicated for the unit BEER DI
21. ood not be stored near or on the kegs e Keg storage and dispensing areas should be kept clean to prevent any possibility of contaminating your draught products rr rr www truemfg com 10 True Food Service Equipment Inc Drue INSTALLATION OPERATION INSTRUCTIONS TEMPERATURE e Correct temperature is a key factor to consider in storing and dispensing draft beer Too cool or too warm may cause flavor loss off taste and dispensing problems Helpful Hints on Controlling Temperature Keep a thermometer handy PRESSURE e Monitor temperature of draft in your cooler and at the tap e Keep cooler door closed as much as possible to avoid temperature fluctuation e Regular maintenance of refrigeration equipment is recommended Dispensing pressures differ according to e The type of draft dispensing system e The length of draft dispensing line e The actual product some require more some require less e The temperature of the product e The pressurizing agent air pressure CO or special blended gases TAPPING Helpful Hints On Maintaining The Correct Pressure Know which pressurizing agent to use on which product and why Monitor your regulators to ensure applied pressure remains constant Keep equipment in good repair Do not agitate the kegs unnecessarily If excessive agitation occurs allow kegs to settle for 1 to 2 hours before tapping TDD 1 COs KNOCK OUT Prior to tapping the keg ensure
22. or two to three days This allows you to be sure electrical wiring and installation are correct and no shipping damage has occurred Remember our factory warranty does not cover product loss REPLACEMENT PARTS TRUE maintains a record of the cabinet serial number for your cooler If at any time during the life of your cooler a part is needed you may obtain this part by furnishing the model number and serial number to the company from whom you purchased the cooler Call Toll Free 800 424 TRUE Direct to Parts Department 800 325 6152 U S A amp Canada only or call 636 240 2400 Drue True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS SHELVING and BIN DIVIDER INSTALLATION OPERATION SHELF INSTALLATION A Hook shelf clips onto shelf standards B Position all four shelf clips equal in distance from the floor for flat shelves C Shelves are oriented so that cross support bars are facing down D Place shelves on shelf clips making sure all corners are seated properly HORIZONTAL BOTTLE COOLER BIN DIVIDER INSTALLATION Horizontal bottle coolers are shipped with bin dividers in place If it is necessary to adjust spacing the following procedure is recommended Step 1 A Dividers are spring loaded push divider towards rear of the cooler to release from front grommeted holes B Lineup divider front pegs with desired holes and punch through interior tape lining of both top
23. ps screw driver 3 8 socket or 3 8 wrench Step 2 A Use a phillips screw diver and remove four screws from the L bracket connected the unit to the wood skid see image 1 Then use a 3 8 socket or wrench and remove the L bracket from the unit see image 2 When lifting unit do not use the countertop as a lifting point Also remember to leave cabinet upright for 24 hours before plugging into power source B Remove skid by unscrewing all base rail anchor brackets Place skid to the side C Carefully upright cabinet LEVELING Step 3 A Set unit in its final location Be sure there is adequate ventilation in your room Under extreme heat conditions 100 F 38 C you may want to install an exhaust fan Warning Warranty is void if ventilation is insufficient B Proper leveling of your True cooler is critical to operating success for non mobile models Effective condensate removal and door operation will be effected by leveling C The cooler should be leveled front to back and side to side with a level Image 1 Removing bracket from skid Image 2 Removing bracket from cabinet D Ensure that the drain hose or hoses are positioned in the pan E Free plug and cord from inside the lower rear of the cooler do not plug in F The unit should be placed close enough to the electrical supply so that extension cords are never used Warning Compressor warranties are void if the unit i
24. r year compressor warranty detailed above will be voided if the following procedure is not carefully adhered to 1 This system contains R404A or R134A refrigerant and polyol ester lubricant The polyol ester lubricant has rapid moisture absorbing qualities If long exposure to the ambient conditions occur the lubricant must be removed and replaced with new For oil amounts and specifications please call True technical service department 800 325 6152 Failure to comply with recommended lubricant specification will void the compressor warranty 2 Drier replacement is very important and must be changed when a system is opened for servicing A drier using XH 7 desiccant or an exact replacement solid core drier must be used The new drier must also be the same capacity as the drier being replaced 3 Micron level vacuums must be achieved to insure low moisture levels in the system 500 microns or lower must be obtained WARRANTY CLAIMS All claims for labor or parts must be made directly through TRUE All claims should include model number of the unit the serial number of the cabinet proof of purchase date of installation and all pertinent information supporting the existence of the alleged defect In case of warranty compressor the compressor model tag must be returned to TRUE along with above listed information Any action or breach of these warranty provisions must be commenced within one 1 year after that cause of action has occurred WHAT IS
25. rench STEP 1 Disconnect power to unit STEP 2 Take off lower grill assembly by removing all Screws STEP 3 Remove bolts anchoring compressor assembly to frame rails and carefully slide out tube connections are flexible STEP 4 Clean off accumulated dirt from condensing coil with a stiff bristle brush STEP 5 Lift cardboard cover above fan at plastic plugs and carefully clean condenser coil and fan blades STEP 6 After brushing condenser coil vacuum dirt from coil and interior floor STEP 7 Replace cardboard cover Carefully slide compressor assembly back into position and replace bolts STEP 8 Reinstall louver assembly onto unit with appropriate fasteners and clips Tighten all screws STEP 9 Connect unit to power and check to see if condenser is running 16 True Food Service Equipment Inc ILe MAINTENANCE CARE amp CLEANING IMPORTANT WARRANTY INFORMATION Condensers accumulate dirt and require cleaning every 30 days Dirty condensers result in compressor failure product loss and lost sales which are not covered by warranty If you keep the Condenser clean you will minimize your service expense and lower your electrical costs The Condenser requires scheduled cleaning every thirty days or as needed Air is pulled through the Condenser continuously along with dust lint grease etc A dirty Condenser can result in NON WARRANTEED part amp Compressor Failures
26. s more than 7 ft 2 1m from plug in connection or an extension cord is used to connect unit to a power supply 7 lga LLE True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS CONDUCTORS AND CIRCUITS Wire Gauge for 2 Voltage Drop in Supply Circuits 115 Volt Distance In Feet To Center of Load Amps 20 30 40 50 60 70 80 90 100 120 140 160 2 14 14 14 14 14 14 14 14 14 14 14 14 3 14 14 14 14 14 14 14 14 14 14 14 12 4 14 14 14 14 14 14 14 14 14 12 12 12 5 14 14 14 14 14 14 14 12 12 12 10 10 6 14 14 14 14 14 14 12 12 12 10 10 10 7 14 14 14 14 14 12 12 12 10 10 10 8 8 14 14 14 14 12 12 12 10 10 10 8 8 9 14 14 14 12 12 12 10 10 10 8 8 8 10 14 14 14 12 12 10 10 10 10 8 8 8 12 14 14 12 12 10 10 10 8 8 8 8 6 14 14 14 12 10 10 10 8 8 8 6 6 6 16 14 12 12 10 10 8 8 8 8 6 6 6 18 14 12 10 10 8 8 8 8 8 8 8 5 20 14 12 10 10 8 8 8 6 6 6 5 5 25 12 10 10 8 8 6 6 6 6 5 4 4 30 12 10 8 8 6 6 6 6 5 4 4 3 35 10 10 8 6 6 6 5 5 4 4 3 2 40 10 8 8 6 6 5 5 4 4 3 2 2 45 10 8 6 6 6 5 4 4 3 3 2 1 50 10 8 6 6 5 4 4 3 3 2 1 1 Wire Gauge for 2 Voltage Drop in Supply Circuits 230 Volt Distance In Feet To Center of Load Amps 20 30 40 50 60 70 80 90 100 120 140 160 5 14 14 14 14 14 14 14 14 14 14 14 14 6 14 14 14 14 14 14 14 14 14 14 14 12 7 14 14 14 14 14 14 14 14 14 14 12 12 8 14 14 14 14 14 14 14 14 14 12 12 12 9 14 14 14 14 14 14 14 14 12 12 12 10 10 14 14 14 14 14 14 14 12 12 12 10 10 12 14 14 14 14 14 14 12 12 12 10 10 10 14 14 14 14 1
27. that all beer faucet in the serving location are in the off position Completely remove the dust cover identification cap from the keg This instruction is True s recommended procedure for installing a remote CO container compartment REQUIRED TOOLS e Pliers e Power Drill e Silicone Sealer e Drill bit 1 2 STEP 1 Remove black knockout plug with a pair of pliers leakage NOTE Knockout plug for CO line can be locate in two different areas View diagram to locate these two areas STEP 3 Snake CO3 line through hole down and around exiting behind rear castor underneath rear grill STEP 4 Seal hole around CO3 line with silicone sealer to prevent cold air STEP 2 Use drill and bit to bore hole straight back through wall into compressor i Knockout Plug can be located at either location E www truemfg com n on 11 Drue True Food Service Equipment Inc INSTALLATION OPERATION INSTRUCTIONS DRAFT BEER PROBLEMS To minimize draft beer problems always follow the recommended instructions for temperature and COz pressures from your beer supplier Flat Beer Description Foamy head disappears quickly Beer lacks usual zestful brewery fresh flavor e CO turned off when not in use e Contaminated air source associated with compressed air e Greasy glasses e Not enough pressure e Pressure shut off during night e Loose tap or vent connection e Sluggish pr
28. tion Remove top cover of draft arm and attach air hose clip to the insulating sleeve at the top of the draft arm Replace top cover The air hose clip will assure that the hose remains in proper place at all times keeping the beer faucet cold See image 7 9 STARTUP Step 5 A The compressor is ready to operate Plug in the cooler B Temperature control set at No 4 position gives refrigerators an approximate temperature of 35 F and glass chiller frosters have an approximate temperature of O E Allow unit to function several hours completely cooling cabinet before changing the control setting C Excessive tampering with the control could lead to service difficulties Should it ever become necessary to replace temperature control be sure it is ordered from your True dealer or recommended service agent D Good air flow in your True unit is critical Be careful to load product so that it neither presses against the back wall nor comes within four inches of the evaporator housing Refrigerated air off the coil must circulate down the back wall LIGHT SWITCH LOCATION The switch is located on the front of the evaporator housing toward the front of the cabinet Open the front doors and the switch will be visible close to the ceiling the cabinet NOTE If the unit is disconnected or shut off wait five minutes before starting again RECOMMENDATION Before loading product we recommend you run your True unit empty f
29. to find the polishing marks Cleaning along the polish lines Polishing lines or grain are visible on some stainless steels Always scrub parallel to visible lines on some stainless steels Use a plastic scouring pad or soft cloth when you cannot see the grain Use alkaline alkaline chlorinated or non chloride containing cleaners While many traditional cleaners are loaded with chlorides the industry is providing an ever increasing choice of non chloride cleaners If you are not sure of your cleaner s chloride content contact your cleaner supplier If they tell you that your present cleaner contains chlorides ask if they have an alternative Avoid cleaners containing quaternary salts as they can attack stainless steel causing pitting and rusting Water Treatment To reduce deposits soften the hard water when possible Installation of certain filters can remove corrosive and distasteful elements Salts in a properly maintained water softener can be to your advantage Contact a treatment specialist if you are not sure of the proper water treatment Maintaining the cleanliness of your food equipment Use cleaners at recommended strength alkaline alkaline chlorinated or non chloride Avoid build up of hard stains by cleaning frequently When boiling water with your stainless steel equipment the single most likely cause of damage is chlorides in the water Heating any cleaners containing chlorides will have the same damaging effects Rinse
30. uctions at ALL times when you replace a C03 gas cylinder 1 Close cylinder at A 2 Remove tap D from barrel Pull pressure release ring on body of tap to release pressure remaining in line do not close C 3 Remove or loosen regulator key B by turning counter clockwise 4 Remove regulator from used cylinder at E 5 Remove dust cap from new gas cylinder at E and clear dust from outlet by opening and closing valve A quickly using appropriate wrench 6 Attach regulator to new cylinder at E use new fiber plastic washer if required 7 Open valve A all the way 8 Close valve C 9 Adjust regulator key B by turning clockwise to set pressure check setting by opening C and pulling and releasing the ring F on the pressure release valve on the body of the tap 10 Tap barrel at D with valve C open NOTE Don t lay CO2 cylinders flat Don t drop CO2 cylinders It requires 1 2 pound CO9 to dispense 1 2 barrel of beer at 38 F with 15 pounds pressure on barrel PRESSURE ADJUSTMENT ON C02 REGULATOR Increasing Pressure 1 Close regulator shut off C 2 Turn regulator key B clockwise and make setting 3 Tap gauge for accurate reading 4 Open regulator shut off C and draw beer Boo OOOO OO A WWW trUeMfZ COM nooo 1 2 Close regulator shut off C Untap barrel at D and to bleed line activate tap handle Leave in open position Slowly open regulator shut off
31. uring transit or installation fire flood or act of God IMPROPER ELECTRICAL CONNECTIONS TRUE IS NOT RESPONSIBLE FOR THE REPAIR OR REPLACEMENT OF FAILED OR DAMAGED COMPONENTS RESULTING FROM ELECTRICAL POWER FAILURE THE USE OF EXTENSION CORDS LOW VOLTAGE OR VOLTAGE DROPS TO THE UNIT NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THERE ARE NO OTHER WARRANTIES EXPRESSED IMPLIED OR STATUTORY EXCEPT THE ONE 1 YEAR PARTS amp LABOR WARRANTY AND THE ADDITIONAL FOUR 4 YEAR COMPRESSOR WARRANTY AS DESCRIBED ABOVE THESE WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES INCLUDING IMPLIED WARRANTY AND MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF OUTSIDE U S This warranty does not apply to and TRUE is not responsible for any warranty claims made on products sold or used outside the United States REMOTE CONDENSERS True warrants the original purchaser of the remote cabinet one year parts and labor coverage for all cabinet parts thereof to be free from defects in material or workmanship under normal and proper use and maintenance service as specified by True This warranty is limited to the cabinet only True assumes no liability for remote condensing units 21 veseeeeceeee WWW tTUCINFZ COM oo eeccceeee 21
Download Pdf Manuals
Related Search