Ford VMM Automobile Parts User Manual
Contents
1. DO NOT remove any fixed covers unless you are authorized qualified to do so for the preparation of this equipment DO NOT obstruct the ventilation of this equipment Obstruction can cause overheating reduce reliability and shorten the life of this equipment DO NOT expose this equipment to spilled liquids CAUTION There are no user serviceable parts under the AN covers unless specifically indicated Always isolate this equipment from the electrical power source disconnect the DC power cable from the vehicle before removing any covers and ensure that all covers are replaced and correctly secured before reconnecting this equipment to the vehicle power VMM HARDWARE MANUAL WARNING Do not alter this equipment s cabling during lightning activity if there is any cabling connecting from the equipment to the outside of the building in which this equipment is installed ie through a pc connector A defective electrical earth connection to any equipment may cause an electric shock hazard This hazard may pass through the signal cabling and to any other equipment interconnected It is recommended that electrical wiring is checked at frequent intervals and whenever alterations are made If signal cables are added to or removed from this equipment switch off the electrical power supply to this and other connected equipment Pollution Degree 2 Normally only non conductive pollution occurs Occasionally a temporary conductivity cau2. B alteration modification or adjustment of the Equipment by other than Hardware Manufacturer s authorized representatives C installation repair or maintenance other than specified operator maintenance of the Equipment or related equipment attachments peripherals or optional features by other than Hardware Manufacturer s authorized representatives D improper or negligent use application operation care cleaning storage or handling E fire water wind lightning or other natural causes F adverse environmental conditions including without limitation excessive heat moisture corrosive elements or dust or other air contaminants radio frequency interference electric power failure power line voltages beyond those specified for the Equipment unusual physical electrical or electro magnetic stress and or any other condition outside of Hardware Manufacturer s environmental specifications G use of the Equipment in combination or connection with other equipment attachments supplies or consumables not manufactured or supplied by Hardware Manufacturer or H failure to comply with any applicable federal state or local regulation requirement or specification governing emission analyzers and related supplies or consumables including without limitation filters printer paper printer ribbons and calibration gases NO OTHER WARRANTIES EXPRESS IMPLIED OR STATUTORY INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTAB
3. Hardware Manual Vehicle Measurement Module VMM Hardware Manual Trademark Acknowledgements Teradyne is a registered trademark of Teradyne Inc All other brands and product names are trademarks or registered trademarks of Teradyne Inc Teradyne Diagnostic Solutions Ltd or their respective owners Ford is a registered trademark of Ford Motor Company Copyright Information VMM Hardware Manual 2005 Ford Motor Company All rights reserved The information specifications and illustrations in this manual are based on the latest information available at the time of printing Ford Motor Company reserves the right to make changes at any time without notice Table of Contents DEFINITIONS ACRONYMS AND ABBREVIATIONS 1 VMM DESCRIPTION sscssecssscsescssscscssecssccsecesceesecsseeseceseceseeeseeseeeseeeseeseeeseeseaeees 2 SAFETY WARNINGS 3 VMM SAFETY INFORMATION 2 cscscsssscscssssesscsssssccseseserscsesssecsesererseserers 3 PROPER INSTALLATION AND USE OF THIS EQUIPMENT 2 ceseccccceseeneseeeeecceccccennesseeseeeeeees 3 IMPORTANT SAFETY INSTRUCTIONS sscssecssccsecsscsssccsscessceseeeseeeseesseeseeeees 7 LED STATUS 9 TROUBLESHOOTING 11 VMM TECHNICAL SPECIFICATIONS ssccssscseccssessesssccssceseeeseeeserssees
4. VMM HARDWARE MANUAL VMM Description he Vehicle Measurement Module VMM is a high performance ruggedized vehicle instrumentation gateway The VMM unit is housed in a magnesium enclosure with a tough protective plastic cover for the PCMCIA expansion slot which can for example be used for wireless LAN cards or memory expansion The VMM device contains four LED status indicators to provide the user with a visual mode of operation for the VMM and host device The VMM also has detachable cables for connection to industry standard high speed host interfaces as well as to the vehicle under test VMM HARDWARE MANUAL Safety Warnings VMM Safety Information You should read and understand this safety information before installing assembling and using the equipment DO observe the safety warnings and cautions in this document WARNING This indicates the presence of a hazard that can cause personal injury if the hazard is not avoided CAUTION This indicates the presence of a hazard that can cause damage to a vehicle or other equipment connected to or that might corrupt software if the hazard is not avoided Proper Installation and Use of this Equipment This equipment has been designed manufactured and tested to meet the requirements of international safety standards however like any apparatus care must be taken in its installation and use DO NOT allow cables connected to this equipment to be positioned
5. a host platform or any resulting damage that may occur to the Equipment accessories or host platform used in conjunction with the Equipment No service support coverage is provided for diagnosing communications issues between the Equipment and any host platform This Warranty does not cover and separate charges for parts labor and related expenses shall apply to any damage to malfunctioning inoperability or improper operation of the Equipment caused by resulting from or attributable to A abuse misuse or tampering B alteration modification or adjustment of the Equipment by other than Hardware Manufacturer s authorized representatives C installation repair or maintenance other than specified operator maintenance of the Equipment or related equipment attachments peripherals or optional features by other than Hardware Manufacturer s authorized representatives D improper or negligent use application operation care cleaning storage or handling E fire water wind lightning or other natural causes F adverse environmental conditions including without limitation excessive heat moisture corrosive elements or dust or other air contaminants radio frequency interference electric power failure power line voltages beyond those specified for the Equipment unusual physical electrical or electro magnetic stress and or any other condition outside of Hardware Manufacturer s environmental specifications G use of the Equipment
6. damages and are a penalty General The waiver by either party of or failure to claim a breach of any provision of this contract shall not be deemed to be a waiver of any provision of this contract shall not be deemed to be a waiver of any subsequent breach or to affect in any way the effectiveness of such provision This contract constitutes the entire agreement between the parties and may not be changed except by an instrument in writing signed by the party to be charged This contract may not be assigned by Buyer without the Seller s prior written consent Seller may assign this contract at any time but shall not thereby be relieved from any liability hereunder In the event that one or more clauses of this contract are found to be unenforceable illegal or contrary to public policy by court of competent jurisdiction the remainder of this contract shall remain in full force and effect except for the unenforceable illegal or other provisions This agreement is a Michigan agreement and shall be interpreted construed and enforced in accordance with the laws of the State of Michigan United States of America Each of the parties hereto agrees that any legal or equitable action or proceeding with respect to this agreement shall be brought only in any court of the State of Michigan or in any court of the United States of America sitting in Michigan and each of the parties hereto submits to and accepts generally and unconditionally the jurisdicti
7. in combination or connection with other equipment attachments supplies or consumables not manufactured or supplied by Hardware Manufacturer or H failure to comply with any applicable federal state or local regulation requirement or specification governing emission analyzers and related supplies or consumables including without limitation filters printer paper printer ribbons and calibration gases NO OTHER WARRANTIES EXPRESS IMPLIED OR STATUTORY INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED 18 VMM HARDWARE MANUAL Hardware Manufacturer s obligations under this warranty are limited solely to the repair or at Hardware Manufacturer s option replacement of Equipment or parts which to Hardware Manufacturer s satisfaction are determined to be defective and which are necessary in Hardware Manufacturer s judgment to return the equipment to good operating condition Repairs or replacements qualifying under this Warranty will be performed or made on regular business days during Hardware Manufacturer s normal working hours within a reasonable time following Buyer s request All requests for warranty service must be made during the stated warranty period Warranty and Disclaimer Asia Pacific and Africa Hardware Manufacturer warrants only to the original Buyer that under normal use care and service the Equip
8. made for loading use or application of any software on any host platform used in conjunction with the Equipment No warranty is made for any connections to a host platform or any resulting damage that may occur to the Equipment accessories or host platform used in conjunction with the Equipment No service support coverage is provided for diagnosing communications issues between the Equipment and any host platform This Warranty does not cover and separate charges for parts labor and related expenses shall apply to any damage to malfunctioning inoperability or improper operation of the Equipment caused by resulting from or attributable to A abuse misuse or tampering B alteration modification or adjustment of the Equipment by other than Hardware Manufacturer s authorized representatives C installation repair or maintenance other than specified operator maintenance of the Equipment or related equipment attachments peripherals or optional features by other than Hardware Manufacturer s authorized representatives D improper or negligent use application operation care 23 VMM HARDWARE MANUAL cleaning storage or handling E fire water wind lightning or other natural causes F adverse environmental conditions including without limitation excessive heat moisture corrosive elements or dust or other air contaminants radio frequency interference electric power failure power line voltages beyond those specified for
9. with respect to this agreement shall be brought only in any court of the Province of Ontario and each of the parties hereto submits to and accepts generally and unconditionally the jurisdiction of these courts with respect to such party s person and property Each party hereby irrevocably waives any objection to the laying of venue of any such action or proceeding in the above described courts Canadian VMM Hardware Manufacturer s Warranty Agreement Terms and Conditions Warranty and Disclaimer Hardware Manufacturer warrants only to the original Buyer that under normal use care and service the Equipment except as otherwise provided herein shall be free from defects in material and workmanship for Two Years from the date of original invoice Leads probes cables pick ups adapters and all other attachments supplies and consumables except as otherwise provided herein are also warranted for Two Years from the date of original invoice to be free from defects in material and workmanship under normal use Warranty does not apply to equipment leads probes cables pick ups adapters supplies and consumables and all other attachments that fail due to negligence abuse or uses other than those applications for which the product is intended This Warranty does not cover software which is separately warranted No warranty express implied or otherwise is given to any host platform s used in conjunction with the Equipment No warranty is
10. A this equipment CAUTION Do ensure that only those test probes which are required by the diagnostic procedure in use are connected to the VMM while the diagnostic is running and that all test probes are disconnected after the measurement has been taken DO ensure that all connections are made prior to applying voltages to the measurement system and that the lower voltage terminal connection closest to ground is made first and broken last DO NOT use this equipment to measure voltages higher than 450V AC peak lt 20 duty cycle or 200Vrms max VMM HARDWARE MANUAL CAUTION If the VMM system is used to measure hazardous voltages these voltages can appear on the pins of other connectors in the measurement system DO NOT continue to use this equipment if you have ANY doubt that it may not be working properly or it is damaged in any way Switch off power to the equipment disconnect the DC power cord from the vehicle and contact your Hotline Call Centre Support DO NOT connect any equipment to the PC compatible signal interface connections of the VMM until you are Satisfied that the equipment is safe DO NOT connect or disconnect any equipment to or from the PC compatible signal interface connections of the VMM unless the VMM is powered off CAUTION Assurance must be obtained from the manufacturers and suppliers of such equipment that interfaces comply with the requirements for SELV circuits in accordance with IEC 1010 EN 61010
11. Do not let cables hang over edge of table bench or counter or come in contact with hot manifolds or moving fan blades 5 Care should be taken to arrange the cord so that it will not be tripped over or pulled 6 Always unplug equipment from electrical outlet when not in use Never use the cord to pull the plug from the outlet Grasp plug and pull to disconnect 7 Let equipment cool completely before putting away Loop cord loosely around equipment when storing or in the pouch provided 8 reduce the risk of fire do not operate equipment in the vicinity of open containers of flammable liquids gasoline 9 Adequate ventilation should be provided when working on operating internal combustion engines 10 Keep hair loose clothing fingers and all parts of body away from moving parts 11 To reduce the risk of electric shock do not use on wet surfaces or expose to rain 12 Use only as described in this manual Use only manufacturers recommended attachments VMM HARDWARE MANUAL 13 ALWAYS WEAR SAFETY GLASSES WHEN USING GARAGE EQUIPMENT Everyday eyeglasses only have impact resistant lenses they are NOT safety glasses KEEP THESE INSTRUCTIONS IN A SAFE PLACE ENSURE ALL VMM OPERATORS READ AND UNDERSTAND INSTRUCTIONS BEFORE USING THE EQUIPMENT VMM HARDWARE MANUAL LED Status Indicators he VMM unit has four LED status indicators that are visible through LED ID Label The LED status indicators allow the user to visually obs
12. E ENTIRE RISK AND COST OF SERVICE REPAIR AND OR CORRECTION Canadian Terms and Conditions For VMM Hardware 1 Payment and Terms of Payment a If Buyer has requested and Ford Motor Company Seller agrees to sell under the Dealer Open Account payment plan then Buyer shall pay the Total Cash Price shown on the Order Form If Buyer has requested the Installment Plan in Part Il of the Order Form and Seller agrees to sell pursuant to such Plan then Buyer shall pay the Total Cash Price and any interest thereon in accordance with the Loan and Security Agreement to be executed by Buyer and Seller 2 Title to Equipment purchased by Buyer from Seller shall pass to Buyer upon Seller s receipt of all amounts owing by Buyer to Seller hereunder 3 Risk of Loss Seller shall be responsible for risk of loss until Equipment is delivered to the location on the Order Form at which time risk of loss shall transfer to Buyer 4 Acceptance and Inspection Buyer shall be deemed to have accepted Equipment upon Seller s delivery Equipment shall be deemed to have been delivered in good condition unless Buyer gives Seller notice to the contrary within 10 days after Seller s delivery Seller is not responsible for performance of Equipment in conjunction with any host platform or any impact on existing hardware or software a Delays Seller shall not be liable for any failure or delay in delivering Equipment or for any failure to perform any pro
13. EXPERIENCE OR CLAIM INCLUDING BUT NOT LIMITED TO CLAIMS FOR LOSS OF PROFITS INTERRUPTION IN BUSINESS LOST OPPORTUNITY WORK STOPPAGE OR OTHER IMPAIRMENT OF ASSETS ARISING OUT OF BREACH OF EXPRESS OR IMPLIED WARRANTY BREACH OF CONTRACT MISREPRESENTATION NEGLIGENCE STRICT LIABILITY IN TORT OR OTHERWISE ON ACCOUNT OF ENTERING INTO OR RELYING ON THIS AGREEMENT EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Freight and Taxes Freight costs and applicable taxes will be added to the final invoice and will be borne by Buyer Import and export duties VATS and taxes are the responsibility of the Buyer When billed to Buyer all duties VATS and taxes will be included in the invoice Security Interest Until all amounts due hereunder are paid Buyer hereby grants to Seller a continuing security interest in a the Equipment b any substitutions replacements and additions thereto and c the products and proceeds thereof This Order Form shall be deemed a security agreement and a copy thereof may be filed as a financing statement in order to perfect Seller s security interest Buyer hereby authorizes Seller to execute and file all documents deemed necessary by Seller to protect Seller s security interest in the Equipment until the purchase price has been paid in full and pay any filing fees thereof Unless Buyer is in default under the terms and conditions of this Agreement Buyer may retain possession of the Equipment and use
14. ILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED Hardware Manufacturer s obligations under this warranty are limited solely to the repair or at Hardware Manufacturer s option replacement of Equipment or parts which to Hardware 19 VMM HARDWARE MANUAL Manufacturer s satisfaction are determined to be defective and which are necessary in Hardware Manufacturer s judgment to return the equipment to good operating condition Repairs or replacements qualifying under this Warranty will be performed or made on regular business days during Hardware Manufacturer s normal working hours within a reasonable time following Buyer s request All requests for warranty service must be made during the stated warranty period SELLER WARRANTS THAT THE BOOTSTRAP SOFTWARE WILL PERFORM IN ACCORDANCE WITH ITS SPECIFICATIONS BUYER ACKNOWLEDGES THAT THIRD PARTIES PROVIDE ADDITIONAL SOFTWARE WITH THE VMM THIRD PARTY SOFTWARE SELLER MAKES NO WARRANTY EXPRESSED IMPLIED OR STATUTORY INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED RELATIVE TO THE THIRD PARTY SOFTWARE BUYER ASSUMES ALL RISK AS TO THE QUALITY AND PERFORMANCE OF THE THIRD PARTY SOFTWARD IF THE THIRD PARTY SOFTWARE OR ANY RELATED SOFTWARE DOCUMENTATION IS DEFECTIVE BUYER AND NOT SELLER OR ITS AGENTS OR EMPLOYEES ASSUMES TH
15. MM abnormally e sure that the LED 2 is on steady red passed Power On Self Test e If the VMM Power On Self Test POST fails contact the Ford Technical Information Support 11 VMM HARDWARE MANUAL Voltage amp Current Requirements Host Protocols Host Connection Typical Vehicle Connection Enclosure Dimensions Weight Environmental Standards amp Regulatory Compliances VMM Technical Specifications 8V 48V DC 12V nominal at 3 8 0 7 Amps maximum Ethernet 10 100 BaseT USB Detachable Cables PC USB to Ethernet Detachable 7m 23ft battery cable Magnesium service bay fluid resistant 1m freefall impact resistant H 73mm 2 9in W 160mm 6 L 180mm 7in 14009 3 116 without cables Operating 20 C to 50 C 4 F to 122 F at 15 to 95 RH non condensing Storage 20 C to 60 C 4 F to 140 F at 15 to 95 RH non condensing The VMM fulfils the requirements of the CE marking scheme and UL201 12 VMM HARDWARE MANUAL Ci Care and Maintenance Cleaning the VMM witch OFF the power and disconnect the equipment from the power source before cleaning the equipment The VMM should only be cleaned using non abrasive mild cleaning agent Note Dust and other particles should be lightly brushed from the surface before being cleaned Cleaner should be applied to a soft lint free cleaning cloth and never directly to the VMM Do not soak the cle
16. TION IN BUSINESS LOST OPPORTUNITY WORK STOPPAGE OR OTHER IMPAIRMENT OF ASSETS ARISING OUT OF BREACH OF EXPRESS OR IMPLIED WARRANTY BREACH OF CONTRACT MISREPRESENTATION NEGLIGENCE STRICT LIABILITY TORT OR OTHERWISE ON ACCOUNT OF ENTERING INTO OR RELYING ON THIS AGREEMENT EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Freight and Taxes Freight costs and applicable taxes will be added to the final invoice and will be borne by Buyer Import and export duties VATS and taxes are the responsibility of the Buyer When billed to Buyer all duties VATS and taxes will be included in the invoice Security Interest Until all amounts due hereunder are paid Buyer hereby grants to Seller a continuing security interest in a the Equipment b any substitutions replacements and additions thereto and c the products and proceeds thereof This Order Form shall be deemed a security agreement and a copy thereof may be filed as a financing statement in order to perfect Seller s security interest Buyer hereby authorizes Seller to execute and file all documents deemed necessary by Seller to protect Seller s security interest in the Equipment until the purchase price has been paid in full Unless Buyer is in default under the terms and conditions of this Agreement Buyer may retain possession of the Equipment and use it in any lawful manner not inconsistent with the terms and conditions of this Agreement Maintenance Until all
17. amounts due hereunder are paid Buyer a shall use the Equipment carefully and properly at Buyer s own expense shall maintain and repair all items of the Equipment in order to keep them in good order and condition and in particular shall comply fully with the maintenance operating usage or other instructions provided by the Hardware Manufacturer c authorizes Seller or any third party appointed by Seller to inspect the Equipment when necessary d shall at all times keep the Equipment free and clear of all liens charges or encumbrances Authority of Representatives Hardware Manufacturer s sales and service representatives have no authority to bind Seller or Hardware Manufacturer to any terms conditions representations warranties agreements or understandings whether oral or written not specifically set forth in these Terms and Conditions Personal Property Equipment including the Software if applicable shall be kept at Buyer s premises and shall remain personal property regardless of how and to what degree it may be affixed or attached to any building or structure or what may be the consequence of its removal from such building or structure Buyer shall not encumber the Equipment including Software if applicable until all amounts owing to Seller hereunder are paid In addition Seller grants to Buyer and Buyer accepts a nonexclusive license to use the Equipment including the Software if applicable in accordanc
18. aning cloth and take care not to allow cleaning fluid to enter connectors DO switch this equipment off by disconnecting the DC power cord from the vehicle before carrying out maintenance amp cleaning operations see Care amp Maintenance section Use only a well diluted mild non abrasive cleaning agent applied using a soft lint free cloth DO NOT use or apply undiluted cleaning agent directly to the equipment surface and do not soak the cloth Take care that cleaning fluid does not enter connector receptacles Care of Cables It is good practice to always return the cables and probes to their appropriate storage place The cables have been manufactured to high standards but can be damaged by driving vehicles over them or exposing them to excessive temperatures Avoid stretching the cables Vehicle Interface Cables You MUST take care when using these cables as they are capable of passing high current Short circuits are a fire risk 13 VMM HARDWARE MANUAL Support Instructions f the checks in the Troubleshooting section did not resolve your VMM concern contact the Ford Technical Information Support for assistance For U S Ford Dealership support information see www fmcdealer com For Canadian Ford Dealership support information see www inford com For non Ford Dealerships support information is available at www motorcraftservice com 14 VMM HARDWARE MANUAL TERMS AND CONDITIONS FOR HARDWARE 1 Payment a
19. ble to Seller and Buyer as their interests may appear If Buyer fails to insure the Equipment as herein provided Seller may but is not obligated to place such insurance upon the Equipment and the Buyer agrees to pay to Seller on demand the premiums for such insurance placed by Seller In no event shall any insurance coverage be deemed to limit or replace Buyer s obligation to indemnify Seller as provided herein Seller s Remedies In the event Buyer breaches this Agreement Seller has all the remedies available to a seller under this contract and may pursue any other remedy available at law or in equity Should legal proceedings be instituted by Seller to recover any amounts due hereunder or to take possession of the Equipment buyer shall pay all collection and legal expenses including court costs and reasonable attorneys fees Seller s rights shall be cumulative and action on one right shall not be deemed to constitute an election or waiver of the other rights to which Seller may be entitled Termination for Convenience If Buyer notifies Seller that it wishes to terminate any order or this contract for its convenience and Seller accepts such termination Seller will stop all work as promptly as practical but Buyer shall be responsible for a a termination charge equal to 10 of the purchase price of the Equipment prior to shipment of the Equipment or b a restocking charge of 15 of the purchase price of the Equipment if written notic
20. cator operation sequences are based on the latest information available at the time of publication If differences are observed refer to the VMM Hardware Manual on the CD DVD or at the Internet location in which software is obtained for up to date information Software Updates Periodically the user will be able to update the VMM software using the host device when new releases become available 10 VMM HARDWARE MANUAL Troubleshooting sers should perform the following checks to determine if they can resolve any problems with the VMM unit If the VMM is still inoperable after performing the checks contact the Ford Technical Information Support for assistance see Support Instructions chapter for details Troubleshooting Table Problem Symptoms Checks amp Possible Causes VMM will not power On No LED s Make sure that secure cable connections are made turn On between the VMM and vehicle e Make sure that the cables do not have any bent broken missing or dirty corroded cable connector pins e Make sure that the VMM unit does not have any bent broken missing or dirty corroded connector pins e Make sure the VMM is powered from the vehicles battery e Verify battery voltage from the vehicle to the VMM is sufficient 12 V nominal e If the VMM fails to power On after making all the checks above contact the Ford Technical Information Support VMM powers On but operates e Cycle remove connect the power to the V
21. ch insurance upon the Equipment and the Buyer agrees to pay to Seller on demand the premiums for such insurance placed by Seller In no event shall any insurance coverage be deemed to limit or replace Buyer s obligation to indemnify Seller as provided herein 13 Seller s Remedies In the event Buyer breaches this Agreement Seller has all the remedies available to a seller under the Uniform Commercial Code and may pursue any other remedy available at law or in equity Should legal proceedings be instituted by Seller to recover any amounts due hereunder or to take possession of the Equipment Buyer shall pay all collection and legal expenses including court costs and reasonable attorneys fees Seller s rights shall be cumulative and action on one right shall not be deemed to constitute an election or waiver of the other rights to which Seller may be entitled 14 Termination for Convenience If Buyer notifies Seller that it wishes to terminate any order or this Agreement for its convenience and Seller accepts such termination Seller will stop all work as promptly as reasonably possible but Buyer shall be responsible for a a termination charge equal to 10 of the purchase price of the Equipment prior to shipment of the Equipment b a restocking charge of 15 of the purchase price of the Equipment if written notice of termination is received by Seller subsequent to shipment of the Equipment The parties agree that these charges represent liquidated
22. ddition Seller grants to Buyer and Buyer accepts a nonexclusive license to use the Equipment including the Software if applicable in accordance with the terms and conditions set forth herein The license and Equipment shall not be leased sold assigned or otherwise transferred in whole or in part Insurance and Indemnification Buyer shall defend indemnify and hold harmless Seller its subsidiaries affiliates and agents from and against and at Buyer s own expense provide insurance satisfactory to Seller covering any and all losses damages claims expenses and other liabilities including attorneys fees relating to or arising out of i damage loss theft or destruction of the Equipment or ii death injury or property damage connected with the use operation or condition including without limitation defects whether or not discoverable by any party of the Equipment Buyer shall promptly notify Seller of any such claim Seller shall have the right to participate at its own expense in any proceeding for which Buyer has undertaken the defense of Seller and in no event shall Buyer settle any claim against Seller without Seller s prior written consent Buyer shall provide evidence of such insurance to Seller upon demand Seller is under no obligation to examine any insurance certificate or advise Buyer that its insurance does not comply with the requirements set forth herein The losses covered by insurance shall in all cases be paya
23. e of termination is received by Seller subsequent to shipment of the Equipment The parties agree that these charges represent liquidated damages and are a penalty General The waiver by either party of or failure to claim a breach of any provision of this contract shall not be deemed to be a waiver of any provision of this contract shall not be deemed to be a waiver of any subsequent breach or to affect in any way the effectiveness of such provision This contract constitutes the entire agreement between the parties and may not be changed except by an instrument in writing signed by parties This contract may not be assigned by Buyer without the 22 VMM HARDWARE MANUAL Sellers prior written consent Seller may assign this contract at any time but shall not thereby be relieved from any liability hereunder In the event that one or more clauses of this contract are found to be unenforceable illegal or contrary to public policy by court of competent jurisdiction the remainder of this contract shall remain in full force and effect except for the unenforceable illegal or other provisions This agreement is an Ontario agreement and shall be interpreted construed and enforced in accordance with the laws of the Province of Ontario and Federal laws applicable therein Teradyne license agreement will be governed by the laws of the commonwealth of Massachusetts Each of the parties hereto agrees that any legal or equitable action or proceeding
24. e with the terms and conditions set forth herein The license and Equipment shall not be leased sold assigned or otherwise transferred in whole or in part 16 VMM HARDWARE MANUAL Insurance and Indemnification Buyer shall defend indemnify and hold harmless Seller from and against and at Buyer s own expense provide insurance satisfactory to Seller covering any and all losses damages claims expenses and other liabilities including attorneys fees relating to or arising out of i damage loss theft or destruction of the Equipment or ii death injury or property damage connected with the use operation or condition including without limitation defects whether or not discoverable by any party of the Equipment Buyer shall promptly notify Seller of any such claim Seller shall have the right to participate at its own expense in any proceeding for which Buyer has undertaken the defense of Seller and in no event shall Buyer settle any claim against Seller without Seller s prior written consent Buyer shall provide evidence of such insurance to Seller upon demand Seller is under no obligation to examine any insurance certificate or advise Buyer that its insurance does not comply with the requirements set forth herein The losses covered by insurance shall in all cases be payable to Seller and Buyer as their interests may appear If Buyer fails to insure the Equipment as herein provided Seller may but is not obligated to place su
25. erve the operation of the VMM Refer to Fig A for the location of the LED status indicators on the VMM LED ID Label Ports ID Label Battery Host H LED 4 AMBER Host Link Activity LED 3 GREEN Critical Access LED 2 RED Power POST LED 1 GREEN Heart beat Under temperature Fig A LED Location within the VMM Over temperature VMM HARDWARE MANUAL Normal Power up LED Operation The VMM Heart Beat Under temperature Over temperature Operating LED LED1 will be flashed regularly approximately once per second when the VMM software is running normally This LED will flash slowly approximately once every 2 seconds with all other LED s unlit if the VMM is in warm up mode following storage at temperatures below 0 C This LED will flash rapidly approximately five per second with all other LED s unlit if the VMM is shut down due to over temperature The Power POST Diagnostic LED LED2 flashes to indicate boot failure code in the event of a VMM boot POST failure A permanently lit Red LED indicates no failures The Critical Access LED LED3 flashes during critical VMM activity such as Flash Memory access The VMM power source must not be removed while this LED is flashing The Host Link Activity LED LED4 flashes whenever Host packets are being transferred similar to the LED LAN indicator used on PC Ethernet port connector between the VMM and PC Note The LED status indi
26. ision hereof resulting from fire flood or other casualty riot strike or other labor difficulty governmental regulation or other restriction or any other cause beyond Seller s control Unconditional Obligation Buyer s obligation to make payments to Seller or its assignee shall be absolute and unconditional and shall continue unmodified despite a any loss damage or other interruption in the use of Equipment or b any dispute claim counterclaim defense or other right which Buyer may have to assert against Seller or the manufacturer of Equipment Seller s Limitation of Liability BUYER S EXCLUSIVE REMEDY RECOURSE OR DAMAGE FOR ANY DEFECT IN WORKMANSHIP OR MATERIAL OR ANY FAILURE OF THE EQUIPMENT IS 15 VMM HARDWARE MANUAL LIMITED TO THE TERMS AND CONDITIONS OF THE WARRANTIES PROVIDED BY THE HARDWARE MANUFACTURER SELLER MAKES NO WARRANTIES REPRESENTATIONS INDEMNITIES OR GUARANTEES WHATSOEVER WITH RESPECT TO EQUIPMENT EITHER EXPRESS OR IMPLIED ARISING BY LAW OR CUSTOM INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THE LIABILITY OF THE SELLER SHALL BE LIMITED TO THE EXPRESS OBLIGATION TO DELIVER THE EQUIPMENT UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE OR RESPONSIBLE FOR ANY SPECIAL INDIRECT INCIDENTAL CONSEQUENTIAL OR PUNITIVE DAMAGES WHETHER FORESEEABLE OR UNFORESEEABLE WHICH BUYER MAY INCUR EXPERIENCE OR CLAIM INCLUDING BUT NOT LIMITED TO CLAIMS FOR LOSS OF PROFITS INTERRUP
27. it in any lawful manner not inconsistent with the terms and conditions of this Agreement Maintenance Until all amounts due hereunder are paid Buyer a shall use the Equipment carefully and properly at Buyers own expense shall maintain and repair all items of the Equipment in order to keep them in good order and condition and in particular shall comply fully with the maintenance operating usage or other instructions provided by the Hardware Manufacturer c authorizes Seller or any third party appointed by Seller to inspect the Equipment when necessary d shall at all times keep the Equipment free and clear of all liens charges or encumbrances Authority of Representatives Hardware Manufacturer s sales and service representatives have no authority to bind Seller or Hardware Manufacturer to any terms conditions representations 21 VMM HARDWARE MANUAL 11 warranties agreements or understandings whether oral or written not specifically set forth in these Terms and Conditions Personal Property Equipment including the Software if applicable shall be kept at Buyer s premises and shall remain personal property regardless of how and to what degree it may be affixed or attached to any building or structure or what may be the consequence of its removal from such building or structure Buyer shall not encumber the Equipment including Software if applicable until all amounts owing to Seller hereunder are paid In a
28. ment except as otherwise provided herein shall be free from defects in material and workmanship for one year from the date of original invoice Leads probes cables pick ups adapters and all other attachments supplies and consumables except as otherwise provided herein are also warranted for one year from the date of original invoice to be free from defects in material and workmanship under normal use Warranty does not apply to equipment leads probes cables pick ups adapters supplies and consumables and all other attachments that fail due to negligence abuse or uses other than those applications for which the product is intended No warranty express implied or otherwise is given to any host platform s used in conjunction with the Equipment No warranty is made for loading use or application of any software on any host platform used in conjunction with the Equipment No warranty is made for any connections to a host platform or any resulting damage that may occur to the Equipment unit accessories or host platform used in conjunction with the Equipment No service support coverage is provided for diagnosing communications issues between the Equipment and any host platform This Warranty does not cover and separate charges for parts labor and related expenses shall apply to any damage to malfunctioning inoperability or improper operation of the Equipment caused by resulting from or attributable to A abuse misuse or tampering
29. nd Terms of Payment a If Buyer has requested and Ford Motor Company Seller agrees to sell under the Dealer Open Account payment plan then Buyer shall pay the Total Cash Price shown on the Order Form If Buyer has requested the Installment Plan in Part II of the Order Form and Seller agrees to sell pursuant to such Plan then Buyer shall pay the Total Cash Price and any interest thereon in accordance with the Loan and Security Agreement to be executed by Buyer and Seller Equipment shall mean herein the VMM hardware unless the term is expressly limited on the Order Form to the VMM Title to Equipment purchased by Buyer from Seller shall pass to Buyer upon Seller s receipt of all amounts owing by Buyer to Seller hereunder Risk of Loss Seller shall be responsible for risk of loss until Equipment is delivered to the location set forth on the Order Form at which time risk of loss shall transfer to Buyer Acceptance and Inspection Buyer shall be deemed to have accepted Equipment upon Seller s delivery Equipment shall be deemed to have been delivered in good condition unless Buyer gives Seller notice to the contrary within 10 days after Seller s delivery Seller is not responsible for performance of hardware or software in conjunction with any host platform or any impact on existing equipment or software a Delays Seller shall not be liable for any failure or delay in delivering or for any failure to perform any prov
30. on of those courts with respect to such party s person and property Each party hereby irrevocably waives any objection to the laying of venue of any such action or proceeding in the above described courts 17 VMM HARDWARE MANUAL VMM Hardware Manufacturer s Warranty Agreement Terms and Conditions Warranty and Disclaimer North America Hardware Manufacturer warrants only to the original Buyer that under normal use care and service the Equipment except as otherwise provided herein shall be free from defects in material and workmanship for two years from the date of original invoice Leads probes cables pick ups adapters and all other attachments supplies and consumables except as otherwise provided herein are also warranted for two years from the date of original invoice to be free from defects in material and workmanship under normal use Warranty does not apply to equipment leads probes cables pick ups adapters supplies and consumables and all other attachments that fail due to negligence abuse or uses other than those applications for which the product is intended This Warranty does not cover software which is separately warranted No warranty express implied or otherwise is given to any host platform s used in conjunction with the Equipment No warranty is made for loading use or application of any software on any host platform used in conjunction with the Equipment No warranty is made for any connections to
31. period 24
32. sed by condensation must be expected Installation Category 2 Local level appliances portable equipment etc with smaller transient over voltages than Installation Category 3 Over voltage Category The measurements section of the VMM is designed for use in Installation Category 1 Signal level special equipment or parts of equipment telecommunication electronic etc with smaller transient over voltages than Installation Category 2 DO keep the VMM away from devices that generate radio interference heat or prolonged exposure to direct sunlight that may CAUTION Do ensure the is subjected to extreme cause heating of the VMM VMM HARDWARE MANUAL CAUTION Do not use this equipment in close proximity to e Operating mobile phones e Operating mobile transceivers such as amateur radio taxi cabs emergency services e Mobile phone cell repeaters e Broadcast radio and television transmitters e Emergency medical equipment WARNING This is a Class II product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures IMPORTANT SAFETY INSTRUCTIONS 1 Read all instructions before use of the equipment 2 Care must be taken as burns can occur from touching hot parts Do not operate equipment with a damaged cables or if the equipment has been dropped or damaged until it has been examined by a qualified serviceperson 4
33. sseseeeees 12 CARE AND MAINTENANCE c ccccccscsscssscssscsccssecsscessceseceseeeseeeseeseceseneseeeseees 13 CLEANING THE 13 CARE OF GABLES 13 VEHICLE INTERFACE CABLES csccssccsscssssssccssccsecssecssccsseeseceseeeseeeseeseneseneseeeeees 13 SUPPORT 5 14 TERMS AND CONDITIONS FOR VMM 15 VMM HARDWARE MANUFACTURER S WARRANTY AGREEMENT TERMS AND CONDITIONS cccsccssccsssssccssccssscssccscescessceseceseeeseesseesseeseceseceseeeseessessenesecesees 18 CANADIAN TERMS AND CONDITIONS FOR VMM HARDWARE 20 CANADIAN VMM HARDWARE MANUFACTURER S WARRANTY AGREEMENT TERMS AND 23 Note An electronic version of this manual is available on the CD DVD or at the Internet location in which software is obtained VMM HARDWARE MANUAL Definitions Acronyms and Abbreviations LAN Local Area Network LED Light Emitting Diode PC Personal Computer PCMCIA Personal Computer Memory Card International Association Expansion card POST Power On Self Test SW Software TIS Technical Information Support Hotline USB Universal Serial Bus VCM Vehicle Communication Module VMM Vehicle Measurement Module
34. the Equipment unusual physical electrical or electro magnetic stress and or any other condition outside of Hardware Manufacturer s environmental specifications G use of the Equipment in combination or connection with other equipment attachments supplies or consumables not manufactured or supplied by Hardware Manufacturer or H failure to comply with any applicable federal provincial or local regulation requirement or specification governing emission analyzers and related supplies or consumables including without limitation filters printer paper printer ribbons and calibration gases NO OTHER WARRANTIES EXPRESS IMPLIED OR STATUTORY INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL APPLY AND ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY EXCLUDED Hardware Manufacturer s obligations under this warranty are limited solely to the repair or at Hardware Manufacturer s option replacement of Equipment or parts which to Hardware Manufacturer s satisfaction are determined to be defective and which are necessary in Hardware Manufacturer s judgment to return the equipment to good operating condition Repairs or replacements qualifying under this Warranty will be performed or made on regular business days during Hardware Manufacturer s normal working hours within a reasonable time following Buyer s request All requests for warranty service must be made during the stated warranty
35. vision hereof resulting from fire flood or other casualty riot strike 20 VMM HARDWARE MANUAL or other labor difficulty governmental legislation or other restriction or any other cause beyond Seller s control Unconditional Obligation Buyer s obligation to make payments to Seller or its assignee shall be absolute and unconditional and shall continue unmodified despite a any loss damage or other interruption in the use of Equipment or b any dispute claim counterclaim defense or other right which Buyer may have to assert against Seller or the manufacturer of Equipment Buyer has determined Equipment suitability for Buyer s purpose Seller s Limitation of Liability BUYER S EXCLUSIVE REMEDY RECOURSE OR DAMAGE FOR ANY DEFECT IN WORKMANSHIP OR MATERIAL OR ANY FAILURE OF THE EQUIPMENT OR SOFTWARE IS LIMITED TO THE TERMS AND CONDITIONS OF THE WARRANTIES PROVIDED BY THE HARDWARE MANUFACTURER SELLER MAKES NO WARRANTIES REPRESENTATIONS INDEMNITIES OR GUARANTEES WHATSOEVER WITH RESPECT TO EQUIPMENT EITHER EXPRESS OR IMPLIED ARISING BY LAW OR CUSTOM INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THE LIABILITY OF THE SELLER SHALL BE LIMITED TO THE EXPRESS OBLIGATION TO DELIVER THE EQUIPMENT UNDER NO CIRCUMSTANCES SHALL SELLER BE LIABLE OR RESPONSIBLE FOR ANY SPECIAL INDIRECT INCIDENTAL CONSEQUENTIAL OR PUNITIVE DAMAGES WHETHER FORESEEABLE OR UNFORESEEABLE WHICH BUYER MAY INCUR
36. where they can be trapped snagged stretched across sharp edges or create any potential hazard 0 WARNING This equipment must be earthed grounded DO ensure that a competently trained person checks that all the electrical connections including any electrical power cable or any extension leads are properly made in accordance with the instructions VMM HARDWARE MANUAL For continued protection against electric shock certain parts of this equipment including the PC compatible signal interface connections have been designed such that the voltage is limited to a safe value In order to maintain this level of protection it is essential that any equipment connected to this equipment shall have interface connections which are similarly protected Assurance must be obtained from the manufacturers and suppliers of such equipment that interfaces comply with the requirements for SELV circuits in accordance with IEC 1010 EN 60101 DO NOT install this equipment at any location less than 400mm above or 400mm below garage floor level CAUTION This equipment must only be used by trained personnel WARNING If the VMM is being used in a moving vehicle ensure that the VMM and cables do not distract or interfere with the driver or form a hazard in any way DO use this equipment in accordance with the operating procedures CAUTION Use of this equipment in a manner not specified by the manufacturer may impair the protection provided by
Download Pdf Manuals
Related Search