Fantom Vacuum CW233H Vacuum Cleaner User Manual
Contents
1. FANTO NA Commercial Stainless Steel Wet Dry Vacuum OWNER S MANUAL Model CW233H 120V 60Hz 8 3 Amps FANTOM 94 Main Mill Street Door 16 Plattsburgh NY 12901 FOR HOUSEHOLD OR COMMERCIAL USE Tel 1 800 275 9251 IMPORTANT SAFETY INSTRUCTIONS When using your Wet Dry Vacuum basic safety precautions should always be observed including the following 1 Read all instructions before using your vacuum To reduce the risk of fire electric shock or injury 2 Use the vacuum only for its intended use Do not leave the vacuum plugged in when 3 To protect against a risk of electric shock do not unattended Unplug the electrical cord when not immerse any part of the vacuum in water or other in use and before servicing liquids Donotallow to be used asa toy Close attention is 4 Never yank cord to disconnect from outlet instead necessary when used by or near children pets or grasp plug and pull to disconnect plants 5 Do not allow cord to touch hot surfaces Useonly as described in this manual Use only 6 Do not run appliance over cord manufacturer s recommended accessories 7 Do not operate the vacuum with a damaged cord or Do not pull cord use cord as a handle close a plug or if the appliance or any other part of the door on cord or pull cord around sharp edges vacuum has been dropped or damaged To avoid or corners the risk of electric shock do not disassemble or e Do not run unit over power cord K2. Front Caddy Axel Frame Fig 3 Flat Washer 10 Slide a rear wheel onto each side of the axel 11 Place a flat washer against the outside of each wheel onto the axel Repeat on the opposite side wheel 12 Secure each wheel with a cotter pin placed in the hole and wrapped around the axel to secure the wheel to the axel Fig 4 Flat Washer a Flat Washer p n x hi EY Cotter Pin Jt j Axel jt T c A B Em A E Cotter Pin Fig 4 13 Assemble the bracket cover I on the caster bracket and then use the screw F to fasten Fig 5 Fig 5 ASSEMBLING THE CADDY Assemble the Vacuum to the Caddy 1 Make sure that the hose intake is facing forwards and the wheels are at the rear of the unit Using the handles on the canister carefully lower it onto the frame aligning the canister edge with the notches in the frame Fig 6 Notches on Caddy Notches Notches 2 To attach the canister to the handle supports align the canister brackets on each side of canister with the supports Fig 7 3 With the clamp assembly tabs facing downwards slide a clamp assembly onto the right and left caddy support Fig 7 Canister Bracket 4 Place the clamp assembly tabs onto the canister brackets on each side of the canister 5 Tighten the clamp assembly by turning the hand nut clockwise until it is secured on the supports Fig 8 6 To insert the caddy handle onto the right and le
3. 3 Foralonger reach you can attach the other extension tube to the first one 4 Attach the desired attachment for the task onto the end of the extension tube or directly onto the handle of the flexible hose Fig 19 Fig 19 Operating Your Wet Dry Vacuum Warning To reduce the risk of fire or explosion do not operate this unit in areas with flammable gases vapors or explosive dust in the air Flammable gases or vapors include but are not limited to lighter fluid solvent type cleaners oil base paints gasoline alcohol or aerosol sprays Explosive dusts include but are not limited to coal magnesium grain or gun powder Do not vacuum explosive dust flammable or combustible liquids or hot ashes To reduce the risk of health hazards from vapors or dusts do not vacuum toxic materials Toggle Switch Attachments Floor to Carpet Brush Used for dry pick up To use for carpets press toggle switch down to the front of the brush to raise the bristles to switch to bare floor setting press the toggle switch to the back of the brush to lower the bristles Crevice Tool Use for wet or dry pick up in tight corners good for automobiles etc Squeegee Use for wet pick up on flat surfaces to pick up liquids and dry the surface quicker Extension Tubes For an extended reach insert one or two of the extension tubes onto the flexible hose Slide one tube into the other then slide the extension
4. tube assembly into __ the handle end of the flexible hose Attachments slide easily onto the handle end of the flexible hose or the extension tubes OPERATING INSTRUCTIONS Dry Material Vacuuming Warning To reduce risk of electric shock unplug before cleaning or emptying canister Caution To reduce the risk of hearing damage wear ear protectors when using the unit for extended periods of time or when in a noisy area The operation of any utility vacuum can result in foreign objects being blown into the eyes which can result in severe eye damage Always wear safety goggles complying with ANSI Z87 1 or in Canada CSA Z94 3 M88 shown on the package before commencing operation Caution To avoid damage to the motor only use the filter cartridge and dust bag for dry pick up Note To dry the unit if your vacuum was recently used for wet pick up run the vacuum with the filter cartridge and dust bag in place without the hose attached for approximately 10 minutes The air circulating through the unit will dry it 1 Ensure that the filter cartridge and dust bag are correctly installed to avoid leaks and possible motor damage to the vacuum 2 Attach the flexible hose extension tube s and desired attachment 3 Plug unit into electrical wall outlet Turn the power On Off switch to the On position 4 To keep your unit in good running order empty the canister and clean the dust bag and filter cartridge frequently e
5. air dry completely before reinstalling onto the filter holder Note The dust bag is washable but it should be replaced every three 3 to six 6 months depending on usage OE aN Motor Thermostat Important This unit is equipped with a motor protective thermostat If some reason the wet dry vacuum should overheat the thermostat will automatically turn the unit off hodie this occur Push the On Off switch once Disconnect the plug from the power source e Check the source of overheating problem i e clogged hose or filter Wait at least 45 minutes before attempting to reuse the vacuum e After unit has cooled down for 45 minutes plug in the vacuum and push the On Off switch to the On position The vacuum should start again e lf the vacuum still does not start contact customer service at 1 800 275 9251 TROUBLESHOOTING GUIDE Plug unit in firmly Power cord not firmly Check fuse or breaker plugged into outlet Replace fuse reset breaker No power in wall outlet Call 1 800 275 9251 Needs servicing Turn the unit off and unplug Thermostat has tripped from outlet Allow unit to cool down then restart VACUUM WILL NOT OPERATE Empty canister Turn unit off and unplug from VACUUM WILL NOT 1 Canister is full wall outlet Check for object s PICK UP OR Unit clogged in air duct and remove SUCTION POWER Flexible hose extension 3 Turn unit off and unplug from IS WEAK tub
6. ase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by your warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice OWNERSHIP REGISTRATION CARD Please fill out and mail the product registration card within ten 10 days of purchase The registration will enable us to contact you in the unlikely event of a product safety notification By returning this card you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions RETURN TO FANTOM 94 Main Mill Street Door 16 Plattsburgh NY 12901 Model CW233H Appliance model Date purchased Name of store Owner s name Address City State Zip Code Printed in China Copyright Fantom 2006 9
7. canister Warning To reduce the risk of back injuries or falls never lift the vacuum if the canister is full of liquid or debris because it is heavy Scoop or drain enough of the contents to lighten the canister enough so that it can be lifted comfortably Turn the unit Off Unplug unit from electrical wall outlet To empty the canister first remove the filter holder from the canister Lift canister off of the caddy and empty into the appropriate waste container When emptying liquids from the canister it is suggested that the canister be tipped over carefully so that liquid could spill into a drain pipe Warning Be careful not to empty any liquid onto the power cord or the filter holder as this could damage the motor Warning Lifting heavy objects can cause injury Empty frequently to avoid excessive weight a ne et Cleaning Replacing Foam Filter Turn the unit Off Unplug the unit from the electrical outlet Hemove the filter holder from the canister Remove the foam filter from the filter holder The foam filter should be cleaned after every use A severely soiled or clogged filter should be thoroughly washed with fresh tepid water A mild detergent may be used if required Fig 20 5 Letthe foam filter air dry completely before replacing into the vacuum Fig 21 Do not use a washing machine to wash or rinse the filter Do not use a hair dryer to dry it Air dry only Never operate the vacuum for wet pic
8. e clogged wall outlet Check for objects in flexible hose extension tube WATER ESCAPING FROM THE The canister is full Empty the canister EXHAUST ORDERING REPLACEMENT PARTS TO ORDER REPLACEMENT FILTER CARTRIDGE FOAM FILTER OR DUST BAGS OR FOR TECHNICAL SUPPORT for Model CW233H Tel 1 800 275 9251 Monday to Friday 8 30 A M 5 00 P M Eastern Standard Time Please Note Filter cartridge foam filter and dust bag are washable They should however be replaced every three 3 to six 6 months depending on usage to ensure peak performance of your vacuum Important Make sure that dust bag and the foam filter have completely air dried before re installing back into the vacuum Model a Mada ae ee Ye THREE 3 YEAR LIMITED WARRANTY FANTOM warrants this product to be free from defects in material and workmanship for a period of three 3 years from the date of the original purchase This warranty applies only to normal domestic household use Should your appliance fail to operate properly while in use under normal commercial or household conditions within the warranty period return the complete appliance and accessories freight prepaid to FANTOM 94 Main Mill Street Door 16 Plattsburgh NY 12901 If the appliance is found by FANTOM to be defective in material or workmanship FANTOM will repair or replace it free of charge Proof of purchase date must be included Non durable parts including witho
9. e is for use on a nominal 120 volt circuit and has a grounding attachment GRounpinc BLADE plug that looks like the plug illustrated at right Make sure that the appliance is fiction connected to an outlet having the same configuration as the plug No adaptor should be used with this appliance 1 Rev 07 06 PARTS AND COMPONENTS Note Verify that all parts and components are included before assembly Vacuum Parts Vacuum 1 Canister 7 Flexible Hose 2 Hose Intake 8 Extension Tubes x2 3 Locking Clasp 9 Crevice Tool 4 Canister Handle x2 10 Floor to Carpet Brush 5 Power Cord and Hose Storage Hn Squeegee Prusn 6 On Off Power Switch 12 Filter Cartridge 13 Dust Bag 14 Foam Filter Caddy Parts Caddy Hardware A C90 B1 IT Caddy Parts Caddy Hardware 15 Caddy Handle A Cotter Pins x2 16 Caddy Support Left B Flat Washers x4 17 Caddy Support Right C Bolt Lock Washer Nut x4 18 Rear Caddy Frame D Caddy Support Brackets x2 19 Front Caddy Frame E Bolt Lock Washer Nut for Caster x2 20 Axel F Hex Slot Head Screw 21 Rear Wheels x2 G Caster Assembly H Bracket Cover Technical Specifications ie MESA Voltage 120V eoHz Power 8 3 Amps 1000 Watts Illustrations may differ from actual product ASSEMBLING THE CADDY Assembling the Caddy Your vacuum cleaner requires some assembly Ensure that all parts listed on the Parts and Components page are includ
10. ed in the packaging Tools Required for Assembly Phillips Screwdriver Wrench not included included 1 Assemble the caddy frame first Parts required for this step caddy support left caddy support right rear caddy frame and front caddy frame 4 Bolt Lock Washer Locking Nut Fig 1 Left Right Support Support Rear Caddy 4 Bolts Frame 4 Lock Washers 4 Locking Nuts Front Caddy Frame Notches Open Side Up Fig 1 2 Make sure the notches on the caddy frame pieces are sitting open side up Fit the front caddy frame into the rear caddy frame Fig 2 3 Place the right support on the inside of the right side of the caddy frame aligning all openings Note The front caddy support will have to be squeezed to join with rear caddy support 4 Secure the right support with bolt and lock washer C 5 On the inside place a washer onto the bolt and fasten with locking nut C Fig 2 Left Support inside ED p I 4 _ vl n oV Rear Caddy g 0 Front T outside oe R J im center L li ro gd 6 Repeat with the left support securing to the caddy frame 7 Ensure all fastenings are tight using a Phillips screw driver not included and the wrench included 8 Slide the axel through the holes in the rear frame Fig 4 9 On the outside side of the axel place a washer in the groove nearest to the frame Fig 3
11. eep cord away attempt to repair the vacuum Return the vacuum to from heated surfaces FANTOM see warranty for examination and Use only extension cords UL rated or cUL at 15 repair Incorrect re assembly or repair can cause a amperes Extension cords rated for less amperage risk of electrical shock or injury to persons when may overheat Care should be taken to arrange the the vacuum is used cord so that the cord cannot be pulled or tripped over 8 Close supervision is necessary for any appliance Turn off unit before unplugging from electrical outlet being used by or near children Do not leave the Do not handle plug or vacuum with wet hands or vacuum unattended while connected operate without shoes 9 Keep hair loose clothing fingers and all parts of e Do not put any objects into openings Do not use body away from any opening and moving parts with any opening blocked Keep free of dust lint hair 10 Do not use to pick up flammable or combustible and anything else that may reduce air flow liquids such as gasoline or use in areas where e Store your appliance indoors in a cool dry area they may be present Keep your work area well lit 11 Do not pick up anything that is burning or smoking e Do not immerse the vacuum into water or other such as cigarettes matches or hot ashes liquids 12 Use extra care when cleaning on stairs Keep end of hose wands and other openings away 13 This unit should not be used to pick up liquids
12. from from your face and body containers sinks tubs etc Using improper voltage may result in damage to the 14 Do not use on uneven surfaces Do not tip tilt unit motor and possible injury to the user Correct voltage over when in use is listed on rating label 15 Intended for indoor or outdoor use and for wet pick up but not intended to be exposed to rain WARNING The power cord on this product contains lead a chemical known to the State of California to cause birth defects or other reproductive harm Wash hands after handling SAVE THESE INSTRUCTIONS For Household or Commercial Use Only GROUNDING INSTRUCTIONS This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances GROUNDED OUTLET BOX WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded Do not modify the plug Y provided with the appliance if it will not fit the outlet have a proper outlet installed V P by a qualified electrician This applianc
13. ft caddy supports fit the ends of the caddy handle into the openings of the left and right caddy supports and push down until the caddy handle clicks into place Fig 9 y a Fig 9 Filter Assembly This wet dry vacuum requires different filter assembly for wet or dry pick up The filter cartridge and dust bag are required for dry pick up Fig 10 The foam filter is required for wet pick up Fig 11 Dry Pick UP Wet Pick UP Filter Cartridge Dust Bag Foam Filter Fig 10 Fig 11 For Dry Pick U Warning To reduce risk of electric shock unplug before cleaning assembly or emptying canister 1 Toassemble the filter for dry pick up turn the filter holder upside down on a level surface Fig 12 2 Place the filter cartridge onto the filter holder inside the filter cartridge is aligned with the slot on the Knob locking knob until it stops TIERS Fig 13 ll I II I Iiii Il ul the vacuum without the filter il JU III cartridge and dust bag in _ ensuring that the locking tab Fig 12 filter holder and turn the Important Do not operate iil place for dry pick up OPERATING INSTRUCTIONS 3 Place the dust bag onto the filter cartridge ensuring that the elastic at the bottom of the bag is at the bottom of the filter Fig 14 4 Turn the filter holder over Tr and place in the vacuum pss canister with the power C ae EP cord in the rear M ME Warning Grasp the
14. kup without the foam filter in place mda i dm OPERATING INSTRUCTIONS Cleaning Replacing Filter Cartridge Dust Bag Warning To reduce risk of electric shock unplug before cleaning assembly or emptying canister Warning If picking up any type of renovating dust a protective mask should be worn The filter cartridge is washable It should however be replaced every three 3 to six 6 months depending on usage to ensure peak performance of your vacuum gd and Replacing the Filter Cartridge Turn the unit Off Unplug the unit from the electrical outlet Remove the filter holder from the canister Remove the dust bag from the filter holder Turn the locking knob to unlock the filter cartridge from the filter holder Fig 22 roe poss Locking 4 4 Knob Filter Cartridge 6 Vigorously TapClean the filter cartridge on a hard surface until no more dust is observed falling out from between the pleats of the filter 7 Replace the dust bag over the filter cartridge 8 Replace the filter cartridge and reinstall the filter holder in the vacuum not shown 9 Turn the locking knob to lock the filter cartridge from the filter holder Fig 22 Cleaning and Replacing the Dust Bag Turn the unit Off Unplug the unit from the electrical outlet Remove the filter holder from the canister Remove the dust bag from the filter holder Wash the dust bag in lukewarm water Let the dust bag
15. power Fig 14 cord and hose storage on the filter holder to place the assembly into the canister as cuts may occur from edge of filter holder j Bn 5 Secure the filter holder with the three 3 locking clasps Fig 12 Fig 15 For Wet Pick U Warning To reduce risk of electric shock unplug before cleaning assembly or emptying canister 1 To assemble the filter for wet pick up turn the filter holder upside down on a level surface Fig 12 2 Remove the dust bag and filter cartridge from the filter holder 3 Place the foam filter over the filter holder Fig 16 Important Do not use the filter cartridge or the dust bag for wet Es pick up Fig 16 4 Ensure that the foam filter is all the way down on the filter holder 5 Follow the instructions from the For Dry Pick Up section to assemble the filter holder onto the canister Warning If water is seen to be coming from the exhaust immediately turn the unit off and unplug from electrical outlet Empty canister and clean Important This unit is supplied with a safety feature that will stop air flow if the tank is overfilled or tips over If the airflow is stopped turn the vacuum off empty the canister then reassemble the vacuum and continue vacuuming Assemble the Hose 1 Insert the wide end of the hose into the hose intake Fig 17 2 Attach one of the extension tubes onto the handle part of the flexible hose Fig 18
16. specially when using to pick up fine dust or fine debris This will prevent a build up of mold or mildew Liquid or Wet Vacuumin Warning Do not vacuum up flammable or combustible liquids such as gasoline or use in areas where they may be present Caution To avoid damage to the unit always use the foam filter for wet pick up Unplug unit from electrical wall outlet Place the foam filter on the filter holder and secure the filter holder into place on the canister Attach the flexible hose extension tube s and desired attachment Plug unit into electrical wall outlet and turn the On Off power switch to the On position When vacuuming up large amounts of liquid make sure that the canister is not too full to avoid injury when emptying the canister Caution Avoid tipping the unit when full of water 6 If the liquid being vacuumed passes a specified amount a float valve will rise automatically and cut off the airflow to the unit If this occurs turn the unit Off and unplug the power cord Empty the canister of any liquid The float valve will go down after the unit is turned off 7 When finished vacuuming up the liquids empty the canister remove the flexible hose and run the vacuum for approximately 10 minutes to dry the foam filter This will prevent a build up of mold or mildew wr ac 3 Iw Cleaning and Maintenance Warning To reduce risk of electric shock unplug before cleaning assembly or emptying
17. ut limitation dust bags filters brushes and electrical parts which normally require replacement are specifically excluded from warranty The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by FANTOM This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of FANTOM if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is FANTOM liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Important Carefully pack item to avoid damage in shipping Be sure to include proof of purch
Download Pdf Manuals
Related Search