Eureka 5700-5739 Vacuum Cleaner User Manual
Contents
1. Adapter 1 Locate upper hose adapter on the back of the cleaner N Remove nested wands from back of cleaner for easy access to hose adapter tabs Q Press hose adapter tabs together and pull hose adapter away from cleaner The hose adapter will unscrew off hose for easy access to debris if necessary 4 Check for blockages at cleaner opening and in hose If no blockage is found continue to step 5 If blockage is found clear and continue to step 11 10 11 Lower Hose Adapter Base Hose Locate lower hose adapter on the back of the cleaner Remove lower hose adapter from rear of cleaner by lifting up and twisting Check for blockages in the hose and base hose Flexing the hose may help loosen any blockage If no blockage is found continue to step 8 If blockage is found clear and continue to step 11 l l l _ SS E BRD rra yy aag J ny O00 D I A poo 7 maS Remove hood from cleaner and check for a blockage in the brush roll area Make sure the hose inlet is clear After the blockage is found and cleared replace the hood on the cleaner Place lower hose adapter back into the base hose Install the upper hose adapter onto the back of the cleaner line it up with the cleaner opening and push it against the cleaner until both tabs lock into place NOTE Turn off the switch and unplug the electrical cord before servicing PROBLEM SOLUTION2. Motor will not start Push plug securely into outlet Try another outlet Check circuit breaker Motor suddenly stops Thermal Cut Off see Page 2 Does not clean the carpet or floor Clean or replace the filters Hint If picking up fine dust the filters may not look dirty but a fine substance tends to reduce suction when it blocks the airflow through the filters Be sure the dust bag is properly seated into the cleaner body Page 6 Replace dust bag Page 6 Be sure hose adapter is secure on back of cleaner Page 9 Check base hose and long hose Page 9 Replace a broken cut loose or out of shape belt Clean hair and thread from bristles and end cap area Replace brush roll if bristles are worn No suction at the end of hose Be sure hose adapter is secure Page 9 Clean or replace filters Hint If picking up fine dust the filters may not look dirty but a fine substance tends to reduce suction when it blocks the airflow through the filters Remove any clogs from the hose that restrict the airflow Check base hose and long hose Page 9 Replace dust bag Page 6 Headlight not working Replace light bulb Page 7 Remove hood and clean debris or items from the brush roll area Noise from brush roll area Replace a broken cut loose or out of shape belt Page 8 Cleaner is hard to push Put handle in operating position Tilt the cleaner back to raise the front wheels off floor
3. On Off Switch location on model with standard handle ON OFF Switch International symbol I means On International symbol O means Off Cord Retainer To use push electrical cord down into cord retainer Bag Compartment Latch Pull up on latch to remove bag compartment door giving access to the dust bag and motor filter Filter Door Latch Push down on latch and pivot out for access to the filter compartment Push up on latch to close door Stair Handle To use when cleaning stairs Headlight Handle Release Step on handle release to pull handle back to a comfortable operating position Cleaner Height Setting An adjustment that raises or lowers the cleaner base to match the type of floor surface QO OO 9 Hose Retainers 4 Place hose in retainers to store hose on unit 10 Electrical Cord Hooks 2 Wrap electrical cord around them to store electrical cord on unit The upper cord hook rotates for quick cord release 11 Nested Wand Storage The crevice wand stores inside the larger wand 12 Carrying Handle Use this handle to carry unit from one place to another 13 Dusting Upholstery Brush Storage Store the dusting brush on back of cleaner NOTE WHEN UNIT IS RUNNING DO NOT ATTEMPT TO REMOVE ANY OBJECT WHICH PREVENTS THE BRUSH ROLL FROM TURNING First turn off unit unplug from the electrical socket then remove object from brush roll area E
4. Push the end of the hose in the lower hose retainer to secure Store Hose and Accessories Nested Wands Y Tr oTTT i ee EW Dusting Brush B Z Age tor toh tar T rere hak er Ope el tae ASAS Pia m LEZ i Hi didn i it i Nhe 1 VW Mace wwe Ag gt a oS w Sooke A DN ill 5 Cord Retainer 6 Cord Hook SAAT ll ale UAN NU Z 7 Plug Sy SI 6 Cord Hook Y M as 5 You will find your cord retainer on the handle above the upper cord hook Firmly push the electrical cord down into the cord retainer This will place the cord out of the way the next time you vacuum 6 Next wind the cord around the two cord hooks on the back side of cleaner 7 Secure the plug to the cord to prevent unwinding HOW TO USE NOTE While using accessories do not place cleaner on furniture or steps as the brush roll may cause damage Place cleaner on floor with the handle in storage position 1 To use accessories remove hose from rear of cleaner by lifting up and twisting 1 Handle Release Step on handle release to pull handle back to a comfortable operating position To lower handle M Dusting Upholstery completely to the floor depress handle release a second Brush ime Crevice l Wand Store Helpful Information Hose or Wand A i Operate ye Before cleaning under low RZ furniture check area
5. Then turn the knob to a higher setting Replace a broken cut loose or out of shape belt Page 8 Cleaner height knob will not turn Hint Put handle in operating position Tilt the cleaner back to raise the front wheels off floor Then turn the knob Bag Cover will not go onto cleaner properly Dust bag must be installed properly in cleaner or bag cover will not go onto cleaner Make sure the dust bag cardboard flange is on the support shelf See page 6 Hood cannot be removed from cleaner unless the cleaner height setting is in the lowest or highest position Hood will not come off All three screws must be removed from the top of the hood Page 8 Missing parts or questions Call 1 800 282 2886 between 8 a m to 7 30 p m CST Monday through Friday and 10 a m to 6 30 p m Saturday Know the model and serial num bers when you call 10 THE EUREKA LIMITED WARRANTY What This Warranty Covers Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of one year The warranty is granted only to the original purchaser and members of his or her immediate household The warranty is subject to the following provisions What This Warranty Does Not Cover e Parts of the cleaner that require replacement under normal use such as disposable dust bags filters drive belts light bulbs brush roll bristles impellers and cleaning e Damages or malfunct
6. Warranty Station Return shipping charges will be paid by the Warranty Station When returning parts for repair please include the model type and serial number from the data plate on the cleaner Further Limitations and Exclusions Any warranty that may be implied in connection with your purchase or use of the cleaner including any warranty of Merchantability or any warranty for Fitness For A Particular Purpose is limited to the duration of this warranty Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Your relief for the breach of this warranty is limited to the relief expressly provided above In no event shall Eureka be liable for any consequential or incidental damages you may incur in connection with your purchase or use of the cleaner Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights You may also have other rights which vary by state Questions amp Answers about Genuine Eureka Products Q Why should I use only Genuine Eureka paper bags belts and parts in my Eureka vacuum cleaner A Using Genuine Eureka Products which are made to our exacting specifications and engineered with emphasis on quality performance and customer satisfaction ensures the long life and cleaning efficiency of your vacuum cleaner
7. first PRE for objects that might l harm the unit or block the Clean vacuum hose Under Dusting Upholstery Brush is for furniture blinds books lamp shades shelves curtains draperies cushions and fabrics l l Crevice Wand cleans corners stairs baseboards and 2 Cleaner Height Setting An adjustment that raises or between cushions lowers the cleaner base to match the type of floor surface With the cleaner cord unplugged set the adjustment to lowest setting for maximum carpet cleaning If the cleaner Nested extension wands to add reach is difficult to push move adjustment to next highest setting until cleaner is comfortable to push The brush lt _ gt roll must reach the carpet for effective cleaning For ease in moving the adjustment knob place handle in operating OL position and tilt cleaner back to remove weight from front e Grasp both wands near ridges wheels ee WARNING Avoid injury Keep loose clothing hair fingers and all other parts of body away from e Pull apart any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height ES a ETO setting e Turn ridge end to center e Push wands together 5 ROUTINE MAINTENANCE The instructions in this booklet serve as a guide to routine Installing New Dust Bag maintenance To avoid unnecessary service calls check the dust cup filters belt and brush roll often We sug
8. How can I be sure I am using only genuine Eureka products in my vacuum cleaner Typically packaged products and paper bags are labeled Genuine Eureka Product PO Q Are there any differences between made to fit or imitation and Genuine Eureka paper bags belts and parts A Yes there are some very important differences in materials quality and reliability For Genuine Eureka Value Accept No Imitations THE EUREKA COMPANY Bloomington Illinois 61701
9. Upright Vacuum Cleaner OWNER S GUIDE Household Type 5700 5739 Series 5800 5829 Series IMPORTANT Do not return this product to the store For assembly problems or questions and replacement of broken or missing items contact Eureka s Customer Service Division toll free at 1 800 282 2886 8 a m to 7 30 p m CST Monday Friday and 10 a m to 6 30 p m Saturday To order replacement parts and accessories contact Eureka s Customer Service Division toll free at 1 800 282 2886 8 a m to 7 30 p m CST Monday Friday and 10 a m to 6 30 p m Saturday or visit our web site www eureka com En Mexico llame al 5670 6169 Important Information 2 Assemble Please Retain We suggest you record the model type and serial numbers below They are located on the silver rating plate on your cleaner For prompt and complete service information always refer to these numbers when inquiring about service Brush Roll Brush Roll Belt Model amp Type _ _ How to Remove Serial No Blockages oo Warranty It is also important to keep your receipt as proof of date of purchase 2000 White Consolidated Ltd Part No 72104B 9 03 Printed in China IMPORTANT SAFEGUARDS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER WARNING To reduc
10. You should know the model type and serial number or date code when you call USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to The Eureka Company Service Division 807 North Main St Bloomington Illinois 61701 USA In Canada write to The Eureka Company 866 Langs Drive Cambridge Ontario NSH 2N7 Refer to The Eureka Warranty for complete service information DO NOT OIL the motor or the brush roll The motor and brush roll are permanently sealed and lubricated Thermal Cut Off This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating If the cleaner sud denly shuts off push the on off switch off 0 and unplug the cleaner Check the cleaner for a possible source of over heating such as a full dust cup a blocked hose or clogged filter If these conditions are found fix them and wait at least 30 minutes before attempting to use the cleaner After the 30 minute period plug the cleaner back in and push the on off switch on I If the cleaner still does not run then take it to a Eureka Authorized Service Center for repair QUICK REFERENCE WARNING Avoid injury Keep loose clothing hair fingers and all other parts of body away from any moving part such as the revolving brush Turn off the switch and unplug the cleaner before changing the cleaner height setting On Off Switch location on models with looped handle only
11. e the risk of fire electric shock or injury e Do not use outdoors or on wet surfaces e Do not leave vacuum cleaner when plugged in Turn off the switch and unplug the electrical cord when not in use and before servicing e Do not allow to be used as a toy Close attention is necessary when used by or near children e Use only as described in this manual Use only manufacturer s recommended attachments e Do not use with damaged cord or plug If vacuum cleaner is not working as it should has been dropped damaged left outdoors or dropped into water return it to a service center before using e Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run vacuum cleaner over cord Keep cord away from heated surfaces e Do not use extension cords or outlets with inadequate current carrying capacity e Turn off all controls before unplugging e Do not unplug by pulling on cord To unplug grasp the plug not the cord e Do not handle plug or vacuum cleaner with wet hands e Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair and anything that may reduce airflow e This vacuum cleaner creates suction and contains a revolving brush roll Keep hair loose clothing fingers and all parts of body away from openings and moving parts e Do not place cleaer on furniture or stairs as the brush roll may cause damage P
12. er can be cleaned by vacuuming with another cleaner or washing with mild detergent 3 Reinstall filter after completely dry Use GENUINE EUREKA replacement pre motor filter Part No 71480 Models equipped with Cartridge Filter Only cartridge style filters can be used with these models Check the True HEPA filter each time dust cup is emptied Replace twice a year or as needed True HEPA Cartridge Latch Filter Door Latch E To remove True HEPA cartridge filter 1 Push down on filter door latch and pull door away from cleaner 2 Push down on HEPA cartridge latch and remove filter To replace True HEPA cartridge filter 1 Place bottom tabs of filter cartridge into slots Rotate filter toward cleaner press firmly against cleaner to latch Make sure True HEPA cartridge latch is secured on both sides 2 Replace filter door by placing tabs of door into slots on cleaner Rotate door up and against cleaner until it locks into place NOTE To have the benefit of a sealed True HEPA system you must use one of the True HEPA cartridge filter systems Use GENUINE EUREKA replacement True HEPA filter HF5 Models equipped with Filter Pads Check the filter pad each time the dust cup is emptied Replace twice a year or as needed Filter Pad To remove Filter Pad from filter door 1 Push down on filter door latch and pull door away from cleaner 2 Lift filter pad up and out of filter door Disp
13. gest BEND FLAPS FORWARD PLACE BAG FLANGE emptying the dust cup after every use ON TOP OF SHELF NOTE When vacuuming carpet fresheners or ve L cleaners powder plaster dust or similar fine lt DOK substances the dust cup and filters will require gt more frequent maintenance NOTE Turn off the switch and unplug the electrical cord before changing the filter Never operate the vacuum cleaner without the dust cup or filter assembly in place Removing the Dust Bag Style LS Remove dust bag cover by lifting up on latch and pivoting dust bag cover out and away from cleaner AA N EN Z 7N 4 POSITION BAG BOTTOM BEHIND RIBS Reinstalling the Dust Bag Cover Place the bottom of the dust bag cover on cleaner lining up grooves on outer edge of cover with rails on side of cleaner Rotate cover up pressing against cleaner until it locks into place 2 Grasp dust bag flaps and pull out from cleaner Grooves on inside edge of bag cover ROUTINE MAINTENANCE continued Pre Motor Filter Pre Motor Filter Check the pre motor filter each time the dust cup is emptied Clean or replace as needed To Clean Pre Motor Filter 1 Remove filter centered in the bottom of the dust cup compartment 2 Shake filter to remove excess dust If necessary the filt
14. ions caused by negligence abuse or use not in accordance with the Owner s Guide e Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts What The Eureka Company Will Do The Eureka Company will at its option repair or replace a defective cleaner or cleaner part that is covered by this warranty As a matter of warranty policy the Eureka Company will not refund the consumer s purchase price Warranty Registration Please fill out and return the warranty registration card accompanying your cleaner Obtaining Warranty Service To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station You will find the nearest location in the Yellow Pages under Vacuum Cleaners Service and Repair Be certain that the Warranty Station is Eureka Authorized For the location of the nearest Eureka Authorized Warranty Station or for service information visit www eureka com or telephone toll free USA 1 800 282 2886 Mexico 5670 6169 Canada 1 800 282 2886 If you prefer you can write to The Eureka Company Service Division 807 North Main Street Bloomington Illinois 61701 USA In Canada write to The Eureka Company 866 Langs Drive Cambridge Ontario N3H 2N7 If it is necessary to ship the cleaner outside your community to obtain warranty repair you must pay the shipping charges to the Eureka Authorized
15. lace cleaner on floor with the handle in storage position while using attachments e Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes e Do not use without dust bag or filter s in place e Belt pulleys can become hot during normal use To prevent burns avoid touching the belt pulley when servicing the drive belt e Use extra care when cleaning on stairs e Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present Store your cleaner indoors in a cool dry area Keep your work area well lighted Unplug electrical appliances before vacuuming them Unplug before connecting turbo nozzle model 26 SAVE THESE INSTRUCTIONS To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully into the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way GENERAL INFORMATION Use the cleaner to pick up dirt and dust particles Avoid picking up hard or sharp objects that could damage the vacuum cleaner Service Information The instructions in this booklet serve as a guide to routine maintenance For additional service information telephone our toll free number for the nearest Eureka Authorized Warranty Station
16. ose of old filter pad To replace Filter Pad into filter door 1 Place new filter pad in filter door 2 Replace filter door by placing tabs of door into slots on cleaner Rotate door up and against cleaner until it locks into place Use GENUINE EUREKA replacement HEPA filter HF6 PERIODIC MAINTENANCE How To Change Light Bulb Only for models with a headlight NOTE Turn off the power switch and disconnect the electrical cord before changing light bulb Lower handle Remove the screw from lens cover Pull lens cover from cleaner Pull old light bulb out of socket Push new light bulb into socket Replace lens cover Secure with screw OarwWNh gt Use GENUINE EUREKA replacement light bulb Part No 57940 2 PERIODIC MAINTENANCE CONTINUED Brush Roll The brush roll turns as it Sweeps and combs the carpet nap Remove hair and threads from the brush roll so it continues brushing the carpet To maintain the most efficient cleaning the bristles must touch the carpet To test the bristle length hold a ruler against the underneath side of the cleaner If the bristles no longer touch the ruler replace the brush roll Brush Roll Belt Style U The brush roll belt turns the brush roll to agitate sweep and comb the carpet nap Check the belt regularly to be sure it is in good condition Replace the belt if it stretches cracks or loses tension Cut away any hair or threads wound around the br
17. ush roll or the belt pulley because the buildup could cause the belt to rotate unevenly How To Replace Brush Roll Belt NOTE Turn off the switch and unplug the electrical cord before replacing belt Belt pulleys can become hot during normal use To prevent injury avoid touching the motor shaft when changing the belt 1 Lower handle to floor to change belt 2 Remove three screws indicated by screwdrivers in above illustration Lift hood to remove NOTE The carpet height adjustment has to be in the lowest or highest position to remove or reinstall the hood Motor Shaft Belt Brush Roll 3 Lift left end of brush roll 4 Remove and discard belt 8 Fira T Torii ig if ma 6 Place belt around brush roll pulley 7 Align left end cap with base Push end cap securely into place 8 Pull right side of brush roll to stretch belt Secure rightend cap into base Ps a a Ih og ore y IMPORTANT 9 Rotate brush roll by hand two full rotations to properly position belt 10 Place hood back on cleaner Make sure hood front is behind furniture guard Replace three screws 11 Tighten screws Use GENUINE EUREKA replacement belt Style U Look for the GENUINE EUREKA product symbol Problem Solving To Clear Blockages in Hose NOTE Turn off the switch and unplug the electrical cord before clearing hose Nested
18. x sock rug etc Helpful Information Listen to your cleaner If you notice a change in the sound of the motor or a change in performance it could simply indicate a common usage or maintenance issue Such as a need to raise or lower the carpet height adjustment possible blockage in hose or brush roll area or a broken or loose brush roll belt These are all easy to fix and the instructions are included in this owner s guide Becoming familiar with the information in this guide will help you to get the best possible performance from your new cleaner for many years to come HOW TO ASSEMBLE CAUTION Assemble the cleaner before using CAUTION Moving parts make sure on off switch is in off 0 position before plugging in NOTE Features may vary by model yet all parts assemble the same Attach Handle CAUTION On models with looped handle use special care Do not pinch electrical cord between handle and cleaner Grooves Electrical 1 From rear of cleaner align handle with groove and slide onto cleaner If necessary use thumb and finger pressure to slide handle into position 2 Attach handle with the two 1 inch screws provided in the assembly packet Use a Phillips head screwdriver NOTE Hand tighten with screwdriver to be sure both screws are firmly seated Attach Hose Upper Hose Retainer Hose Lower Hose Retainer 3 Pick up hose and lay across upper hose retainer 4
Download Pdf Manuals
Related Search