Escort ZR3 Radar Detector User Manual
Contents
1. gt Read This First Please read both sides of these Then before installing the other instructions before starting your components plug all of them into installation the Interface and power up the unit to confirm proper operation For the easiest trouble free installation install the Interface first and wire it to a 12 volt switched circuit Important Installation 1 A professional installer must 3 If your vehicle is damaged Warnings install your new Laser Shifter during installation its safety Installation of this system requires systems may be compromised So ee experience and expertise in which could cause personal injury co gt ths E ee automotive electronics Car audio or property damage specialists and many new car dealers can install the Laser Shifter 4 Improper installation may void for you Shifter s warranty 2 Attempting to install this product without expertise in automotive electronics installation can cause personal injury or SHIFTER ZR3 Comes Complete damage to your vehicle Front Laser Shifters Miniature Display Controller Rear Laser Shifter e Twin weather proof sensors e Display Controller mounts easily to e Weatherproof license plate mounted Performance Since Laser signals will not pass instrument pod dashboard or console sensor a through any objects including pon eed Ca ae arning lastic it is critical that the Laser grommets e Velcro and adhesive pads provided for 30 foot cable with modular2. away from hot and moving parts then brought into the vehicle s interior 2 Cable can be cut if necessary for routing Reconnect and solder each of the three wires and seal with heat shrink tubing After all components are installed correctly l Turn the Laser Shifter on by rotating the volume control knob 2 Turn vehicle s ignition to the on position 3 Shifter will cycle through a startup sequence
3. connector p secure mounting Shifters be mounted perfectly e Universal mounting brackets with Documentation level and have an unobstructed stainless steel hardware Interface e Comprehensive Owner s Manual view of the road e Central module connects to switched 12 volt power and ground e Installation Manual J J e e All components plug directly in using Built in Diagnostics modular connections e Confirms all components are operational e 3M connector taps into existing vehicle wiring ESCORT Escort Inc Sales Service 800 964 3143 5440 West Chester Road Fax 513 870 8509 West Chester Ohio 45069 www escortradar com 2002 Escort Inc Escort Passport and Laser Shifter are trademarks of Escort Inc Features specifications and prices subject to change without notice E ent i y 1O Fagg F 0 1 Route Laser Shifter cables to firewall and secure with zip ties Gncluded 2 Route both Shifter cables into the vehicle s interior If there is not a suitable opening drill a 13 32 or 7 16 hole 3 Pull cables through firewall and plug into jacks marked Front Shifter 1 and Front Shifter 2 on interface 4 Pull grommet located on each cable through the firewall to seal the hole Use silicone sealant not supplied if necessary P ene eee SHIFTER ZR3 Installation Manual I Determine the best location for the Display Controller in the vehicle s interior Consult customer i
4. f necessary 2 Install Display Controller using supplied velcro or double sided tape 3 Route cable and plug into jack marked Display on Interface Note 1 Make certain that the Display is clearly visible from the driver s position and that the controls can be easily accessed without interfering with normal driving Note 1 Only drill hole in firewall after thoroughly investigating location first ensuring no other wires hoses etc will be damaged 2 Keep all cables away from moving parts and hot surfaces Radiator hoses etc 3 Do not splice cable l Determine best location for the Laser Shifters For optimum performance install each laser shifter on either side of the front license plate with a clear view of the road If possible center each shifter module between the license plate and the outside edge of the vehicle Gee photo at left 2 Using the supplied mounting bracket mark location Drill pilot holes in the vehicle if necessary 12 Volt Power Line 1 Determine best location for the Remote Mute Button 2 Clean surface area 3 Remove paper backing on the back of the button and press onto surface 4 Route cable and plug into jack marked Mute on Interface E EEE EEE EEE 3 Mount the Laser Shifters using the supplied hardware making sure that each shifter is level to the road Note 1 Do not drill holes in the Laser Shifter itself 2 Thor
5. oughly investigate location before drilling any holes 3 Keep all cables away from moving parts and hot surfaces Radiator hoses etc 4 Do not splice cable 5 Make certain that each Laser Shifter is level and has a clear view of the road Passport 8500 Optional 1 Install Interface under the dash using supplied zip ties DO NOT MOUNT IN ENGINE COMPARTMENT 2 Connect black wire to ground and red striped wire to a switched 12 volt supply df the Laser Shifter is left in the on position it will automatically power on and off with the ignition Use blue 3M connector provided to tap into existing circuit if needed 3 Be sure to plug all cables into the correct labeled jacks I Remove two license plate screws top or bottom 2 Mount Laser Shifter to plate using supplied mounting bracket 3 Route wire through trunk compartment and into the vehicle s interior 4 Insert connector to jack labeled Rear Shifter on Interface l Determine best location for Passport 8500 2 Route optional link cable to ZR3 Interface 3 Connect one end of the cable to the Passport 8500 and the other end to the ZR3 Interface marked 8500 4 Refer to ZR3 Owner s Manual for program ming options if needed Tips 1 Do not block license plate illumination 2 Do not cover any required license plate information Installation Alternatives 1 Cable can be routed under vehicle keep
Download Pdf Manuals
Related Search