Epson 1430 Printer User Manual
Contents
1. You can use most plain paper with your printer and achieve good results Coated papers give better results because they reduce the amount of ink that is absorbed However if the coated paper does not absorb enough ink the ink can smear To ensure the best results EPSON provides coated papers and transparencies that are formulated for the inks used in EPSON ink jet printers To order EPSON papers and transparencies contact your dealer or call EPSON Accessories at 800 873 7766 U S only In Canada call 800 BUY EPSON for sales locations Use the following part numbers when ordering Paper or other media Size Part number Coated paper for 720 dpi Letter 8 5 x 11 inches 5041062 Legal 8 5 x 14 inches S041067 B 11 x 17 inches S041069 Super A3 B 13 x 19 inches S041070 Coated paper for 360 dpi Letter 8 5 x 11 inches S041060 Super A3 B 13 x 19 inches 85041066 High quality glossy paper Letter 8 5 x 11 inches S041072 B 11 x 17 inches 5041074 Super A3 B 13 x 19 inches S041075 Letter 8 5 x 11 inches S041064 Transparency film The built in tractor feeder allows you to print on continuous paper up to 17 inches 432 mm wide or banner paper up to 16 inches 406 mm wide You can also use the tractor feeder to print on continuous labels When using coated paper glossy paper transparencies envelopes labels or banner paper keep the following in mind LI Use coated pa2. EPSON Stylus 1500 15 EPSON Stylus 1500 3 Move the paper release lever to the single sheet position Note If the Data and Paper Out lights flash you may have moved the paper release lever before feeding the paper backward to the paper park position Lower the paper release lever to the continuous paper position and press the Load Eject button then raise the paper release lever to the single sheet position 4 Change the driver settings to match your paper source size and type 5 The printer is ready to print When it receives data it loads a single sheet from the sheet feeder or manual feed slot Note The paper eject guides raise automatically when a single sheet is loaded from the sheet feeder Switching to Continuous Paper To switch from single sheets back to continuous paper follow the steps below 1 Ifa single sheet is in the paper path press the Load Eject button to eject it 2 Raise the paper release lever to the continuous paper position Note If the Data and Paper Out lights flash you may have moved the paper release lever before ejecting a sheet of paper Raise the paper release lever to the single sheet position and press the Load Eject button then lower the paper release lever to the continuous paper position 3 Lower the page eject guides 4 Change the driver settings to match your paper source size and type 5 The printer is ready to print When it receives data it loads cont
3. Printer Specifications Printing Printing method Nozzle configuration On demand ink jet 64 monochrome black nozzles 60 color cyan magenta yellow nozzles 20 x 3 20 for each color Printable columns and printing speed LQ printing Draft printing Character pitch speed speed characters per Printable characters characters inch columns per second per second 10 136 200 400 12 169 240 480 15 200 300 600 17 10 condensed 233 343 686 20 12 condensed 272 400 800 Resolution Maximum 720 x 720 dpi Paper feed speed 72 milliseconds per inch line Input buffer 256KB Print direction Control code Line spacing Character tables Character sets Ink Jet Printers Bidirectional with logic seeking for text and graphics unidirectional and autodirectional modes available in Default Setting mode ESC P 2 and expanded raster graphics code IBM XL24E emulation code Y inch default 4 inch or programmable in Y46o inch increments 1 Italic and 10 graphics character tables 1 legal and 14 International character sets 1 96 Paper Note EPSON Stylus 1500 Since the quality of any particular brand or type of paper may be changed by the manufacturer at any time EPSON cannot guarantee the use of any particular brand or type of paper Always test samples of paper stock before purchasing large quantities or printing large jobs Paper sheets Si
4. Make sure the Ink Out 0 light goes off Note If the Ink Out O light remains on the ink cartridge may not be installed correctly Remove the ink cartridge and then reinsert it as described above 8 Replace the ink compartment cover 9 Press the Pause button to resume printing 10 If you want to check the print quality print a demonstration page Replacing the Color Ink Cartridge Follow these steps to remove the empty color cartridge and install a new one 1 Make sure the printer is on 2 Press the Pause button check that the Pause light comes on 3 Open the printer cover using the notch on the cover 4 Hold down the Alt button for about five seconds until the print head moves slightly left to the ink cartridge install position The Pause light begins blinking The carriage returns to the home position after 30 seconds if the ink cartridge is not removed 5 Pull up the cartridge clamp to open it The cartridge rises partially out of the printer EPSON Stylus 1500 17 EPSON Stylus 1500 10 11 12 Lift the cartridge out of the printer and dispose of it carefully so any excess ink does not spill out Do not take the used cartridge apart or try to refill it W Warning If ink gets on your hands wash them thoroughly with soap and water If ink gets into your eyes flush them immediately with water Remove the ink cartridge from its protective bag Remove the tape seal from the top of the c
5. appropriate for the media you loaded Printing on Continuous Paper The built in tractor feeder lets you print on continuous paper from 4 inches 102 mm to 16 inches 406 mm wide You can use the tractor feeder without removing paper from the sheet feeder When printing on continuous paper keep the following in mind A When you turn on the printer with paper loaded on the tractor feeder it reverses the paper to the paper park position and then advances it to the next page To keep the loading position accurate remove any printed sheets before you turn off the printer Q If the printer runs out of paper during a print job load paper onto the push tractor and press the Pause button to continue printing Q If printing appears too high or low on the page you can use micro adjust mode to adjust the loading position or tear off position The settings you make remain in effect until you change them again even if you turn off the printer EPSON Stylus 1500 14 C Caution Do not use the knob on the left side of the printer to adjust the loading position this may damage the printer or cause it to lose the top of form position Q If the paper is released from the sprocket pins never feed paper backward this may cause a paper jam Reload the paper by following the instructions in the next section Loading Continuous Paper Follow these steps to load continuous paper in the printer 1 Place the supply of continuous paper di
6. hold down the Pause button for about three seconds Both Font lights begin to flash To exit micro adjust mode press Pause again The settings made in this mode are saved in the printer s memory Ink Jet Printers EPSON Stylus 1500 Load Eject Loads or ejects a sheet of paper The printer normally loads and ejects paper automatically When using continuous paper press this button to feed paper backward to the paper park position Button combinations and power on functions The button combinations below perform additional functions to control your printer Alt Pause Reset Clears the printer s buffer and resets the printer settings to their factory defaults Alt LF FF Cleaning 0 Cleans the black print head see Cleaning the Print Heads Alt Load Eject Cleaning NNN Cleans the color print head see Cleaning the Print Heads Pause Operate button Printer adjustment mode Enters printer adjustment mode and prints a multilingual instruction sheet on calibrating the printer Paper must be loaded in the printer Hold both buttons until the font lights flash Use this mode only if you are printing from DOS applications To exit printer adjustment mode press the Pause button and turn off the printer Note When using the following Operate button combinations wait until the Data light flashes or paper is loaded before releasing the buttons Load Eject Operate button LQ self test Checks the
7. Namer Easy instali 7 You can install the Network Driver Package containing the driver and three utilities or you can select the components individually To install the package click Network Driver Package You do not have to install the utilities However you must install the AT StylusC olor driver If you do not install the utilities and you need to use them later you must run the installer again Note Do not select the Serial Driver Package or the StylusColor driver The driver and its utilities are described below L AT StylusColor driver This driver lets you use the optional AppleTalk interface to connect the printer to an AppleTalk network L Epson Monitor2 This utility manages print jobs that have been sent to the printer Background printing must be on to use the Epson Monitor2 Utility L Bi D Calibration Utility This utility calibrates the printer so vertical lines are aligned L EPSON Namer This utility assigns a unique name to the printer 8 Click Install to copy the software to your hard disk and follow any instructions on the screen 9 When the installation is complete click Restart to eject the driver diskette and restart the computer The Installer places the Bi D Calibration Utility in a new folder called Stylus 1500 Folder the Epson Monitor2 Utility in the Extensions folder and the EPSON Namer on your hard drive Remember to assign a name to the printer and select the pri
8. by switching to monochrome mode To do this turn off the printer then turn it back on and resend your print job If the black ink cartridge is empty you cannot continue printing even if the color cartridge still contains ink Selecting the Correct Ink Cartridges Use only these EPSON ink cartridges in your Stylus 1500 printer Black ink cartridge S020062 Color ink cartridge S020049 C Caution Use only genuine EPSON ink cartridges and do not refill them Other products may cause damage not covered by EPSON s warranties Ink Jet Printers EPSON Stylus 1500 Replacing the Black Ink Cartridge Follow these steps to remove the empty black ink cartridge and install a new one 1 Make sure the printer is on 2 Press the Pause button check that the Pause light comes on 3 Remove the ink compartment cover 4 Carefully pull the used ink cartridge straight out of the printer and dispose of it so any excess ink does not spill out Do not take the used cartridge apart or try to refill it W Warning If ink gets on your hands wash them thoroughly with soap and water If ink gets into your eyes flush them immediately with water 5 Remove the ink cartridge from its package 6 Insert the end of the cartridge with the foil plug into the ink compartment following the directions on the cartridge label 7 Push the cartridge all the way into the compartment until the cartridge meets the back of the ink compartment
9. eject guides 12 Make sure the rear edge guide of the paper support is pushed under the output tray to prevent a paper jam 13 When the printer receives data it advances the continuous paper to the loading position and starts printing Removing Continuous Paper Follow these steps to remove continuous paper from the printer 1 After you have finished printing a page of continuous paper press the Load Eject button The printer advances the paper to the tear off position Note If the auto tear off feature is on you can skip step 1 because the printer advances the paper perforation to the tear off position automatically 2 Tear off the printed pages 3 Press the Load Eject button The printer feeds the continuous paper backward to the paper park position Switching Between Continuous Paper and Single Sheets When using the tractor feeder you can easily switch between single sheet and continuous printing without removing either type of paper Switching to Single Sheets To switch from continuous paper to single sheets follow these steps 1 If any printed sheets remain in the printer tear off the printed Pages 2 Press the Load Eject button The printer feeds the continuous paper backward to the paper park position Caution Always tear off paper before back feeding back feeding too many sheets can cause a paper jam Never back feed labels Labels can easily come off their backing and jam the printer
10. idea to make a backup copy of your driver diskette EPSON Stylus 1500 10 Installing the Windows Printer Driver If you are using Windows 3 1 follow the steps in the next section to install the printer driver Installing the Driver for Windows 3 1 Follow these steps to install the printer driver for Windows 3 1 1 Turn on your printer and computer 2 Make sure Windows is running 3 Insert the Windows printer driver diskette in a diskette drive 4 In the File menu select Run You see the Run dialog box 5 In the Command Line box type A SETUP or B SETUP if you inserted the diskette in drive B Press Enter or click OK You see the EPSON Printer Driver Setup dialog box 6 Highlight EPSON Stylus 1500 in the Printer Driver pull down menu and click Continue The installation program begins copying the driver files You see a screen showing the progress of the installation as it proceeds After a few moments the installation program creates the EPSON program group in Windows containing these icons EPSON Calibration Utility Spool Manager EPSON Stylus Help EPSON Stylus ReadMe When the installation is complete you see a confirmation screen 7 Click OK to exit the installation program 8 Calibrate your printer using the EPSON Calibration Utility The installation program automatically selects the EPSON Stylus 1500 printer as your default printer for Windows applications and assigns the printer driver to por
11. mm for US B landscape and US C portrait C The minimum bottom margin is 0 55 inch 14 mm Note The maximum printable width is 13 6 inches 345 mm Envelopes A nae Ai Spr LAs L c A The minimum top margin is 0 33 inch 8 5 mm B The minimum left margin is 0 12 inch 3 0 mm The minimum right margin is 0 12 inch 3 0 mm C The minimum bottom margin is 0 55 inch 14 mm Note Load envelopes long edge first face down Continuous paper N ee ee ee w w Youlo oo oo o o o A The minimum top and bottom margins above and below the perforation are 9 0 mm 0 35 inch B The minimum left and right margins are 0 51 inch 13 mm Note The maximum printable width is 13 6 inches 345 mm 1 96 Ink Jet Printers Ink Cartridges Black ink cartridge S020062 Color Black Print capacity 1900 pages A4 paper text Cartridge life 2 years from production date and up to 6 months after opening the package at 77 F 25 C Temperature Storage 22 to 104 F 30 to 40 C 1 month at 104 F 40 C 22 to 140 F 30 to 60 C 1 month at 104 F 40 C 120 hours at 140 F 60 C Freezing 27 F 3 C 1 0 inch W x 5 5 inches D x 4 2 inches H 25 1 mm W x 139 6 mm D x 105 3 mm H Color ink cartridge S020049 Transit Dimensions Colors Cyan magenta and yellow Print capacity 320 pages A4 360 dpi 5 of each color Cartridge life 2 years
12. name is selected in the Models pull down list and click OK At the next screen you can give the printer a unique name We recommend that you keep the model name but you can type a new one in the Printer name box if desired To use the printer as the default printer for all Windows 95 applications select Yes No is the default Click the Next button At next screen select YeS to print a test page Click the Finish button The program copies the files to your hard disk and adds an icon using the printer name to the Windows 95 Printers folder Then it sends a test page to the printer Wait for the page to print completely Select Yes again at the test page confirmation screen if the page printed correctly If it did not print correctly there may be a problem with the printer connection check the connection and start over Your computer finishes loading Windows 95 To run the Setup program and install the rest of the printer software in an EPSON folder click Start then select Run You see the Run dialog box In the Open pull down menu type A SETUP or B SETUP and click the OK button You see the EPSON Printer Driver Setup dialog box Highlight your printer model name in the Printer Driver pull down menu and click Continue The installation program begins copying the files to your hard disk and shows the progress of the installation as it proceeds After the status bar disappears the driver continues installing for a m
13. paper length and performs a printer self test at 360 dpi see Testing the Printer LF FF Operate button Draft self test Checks the paper length and performs a printer self test at 180 dpi see Testing the Printer LF FF Load Eject Operate button Hex dump When connected to a PC prints a page containing a hexadecimal representation of the data sent to the printer hex dump for troubleshooting use To exit hex dump mode press the Pause button and then turn off the printer Alt Operate button Demonstration page Prints a demonstration page of the printer s fonts and colors Paper must be loaded in the printer To exit demonstration mode press the Pause button and then turn off the printer Note If the printer is in economy mode when a demonstration page is printed black will print as gray Economy Condensed Operate button Default Setting mode Enters the printer s Default Setting mode see the next section for more information To exit Default Setting mode press the Pause button and then turn off the printer EPSON Stylus 1500 5 EPSON Stylus 1500 Alt Pause Operate button Ink smear prevention mode Decreases the printing speed to allow more time for the ink to dry Use this function when your output is smeared This mode is not saved as a default setting Using the Default Setting Mode Additional printer functions are available through the Default Setting mode If you nee
14. self test or demonstration page Flashes when data is being received by the printer Ink Out O On when the black ink cartridge is empty or not installed The printer will not work if the black ink cartridge is empty or not installed Flashes when the black ink cartridge is low on ink Ink Out NNN On when the color ink cartridge is empty Flashes when the color ink cartridge is low on ink If color ink runs out while you re printing the printer stops You can continue to print with the black ink cartridge by switching to monochrome printing To do this turn off the printer turn it on again and resend your print job PaperOut On when the printer runs out of paper Flashes rapidly if there is a paper jam Pause On when printing is paused Flashes while the ink cartridge is being replaced or during print head cleaning Ink Jet Printers Economy On when economy printing mode is selected In economy mode the printer uses less ink by printing fewer dots per character Note that black may print as gray Use this mode for rough drafts of text only Condensed On when condensed mode is selected In this mode the printer prints selected fonts at 60 of their width so that more characters can fit ona page Font Indicates which font is selected Use the Default Setting mode to select fonts other than those displayed on the control panel Both lights flash when the printer is in micro adjust mode Buttons In addition
15. three initialization methods reset the font according to the default settings selected using the control panel However ESC does not initialize the printer mechanism clear the input data buffer or clear the user defined character set The control panel initialization does not initialize the printer mechanism or clear the user defined character set Default Settings The table below shows the default settings that take effect when the printer is initialized In addition hardware and control panel initialization erases any text in the data buffer Item Default setting Top of form position Current paper position Page length Single sheets measured by self test printing Left and right margins Cancelled Line spacing Y inch line spacing EPSON Stylus 1500 4 described in this section Most printer settings can be controlled from your software ly Operate Ink Out Ak Data Ink Out 000 Paper Out Cleaning Reset Micro Adjust e C a D h m m Draft 10cpi LF FF mO Draft 12cpi Pause 3sec E Courier 10cpi Cleaning OE Courier 12cpi OOO OO Roman T PS Economy o0 Sans H PS Om Others Load Eject Condensed Font Lights Operate On when the printer is on Data On when data remains in printer memory or when printing a
16. want to clean the printer follow these steps 1 EPSON Stylus 1500 18 Turn off the printer and disconnect any cables connected to it Be sure to keep the printer cover closed as you clean it Remove any paper or other media from the sheet feeder and rear tractor Carefully clean away loose dust and dirt with a soft brush 1 96 4 Clean the exterior with a soft dampened cloth 5 To clean ink out of the printer s interior wipe it gently with a damp cloth C Caution Never use alcohol or thinner to clean the printer these chemicals can damage the components and the printer case Do not use a hard or abrasive brush these can scratch the printer surfaces Do not allow water to get on the printer mechanism or any electronic components Do not touch the gears inside the printer Do not spray inside the printer with lubricants or oils they can damage the printer mechanisms Information Reference List Engineering Change Notices Z one mJ roduct Support Bulletins one echnical Information Bulletins zH Z one Related Documentation TM STYLUS15 EPSON Stylus 1500 Service Manual PL STYLUS15 EPSON Stylus 1500 Parts Price List 4005097 EPSON Stylus 1500 Reference Guide 4005095 EPSON Stylus 1500 Setup and Software Guide for Windows 4005096 EPSON Stylus 1500 Setup and Software Guide for Macintosh Ink Jet Printers
17. you selected Not aligned in step 7 select the sample that is most closely aligned 9 Repeat steps 6 through 8 until all the patterns have been aligned When the calibration is complete click Finish to exit the program Calibrating with a Macintosh 1 Open the Stylus 1500 folder and double click Bi D Calibration Utility 2 You see a prompt asking you to choose how your printer is connected Click Network 3 You see the Bi D Calibration Utility screen Select your printer and print head Printer Type either Stylus 1500 monochrome or Stylus 1500 color to be calibrated Ink Jet Printers EPSON Stylus 1500 4 Make sure paper is loaded in the printer then click the Preview button to print a preview of all available calibration patterns Use these pages to select the patterns that need to be calibrated Note If you want to stop printing the preview patterns press Pa use and then turn off the printer using the O perate button 5 For example if the lines shown under Pattern 2 need to be aligned highlight Pattem 2 in the Choose Pattern pop up menu and then click Start Wait while the printer prints a page containing multiple patterns of vertical lines each assigned with an offset value In most patterns the vertical lines are slightly misaligned Look for the pattern that is most closely aligned l l l l Aligned Not aligned 6 Enter the offset value of the pattern that is most closely aligned in the No box
18. 6 inch Others Skip over perforation Off On Auto tear off Off On Print mode Plain paper true black Plain paper composite black Exclusive paper Transparency Banner paper Off On IBM mode only EPSON Stylus 1500 6 Print direction Specifies how the print head moves across the page The options are Uni D Bi D and Auto default When Uni D is on the print head prints in only one direction to provide the most precise alignment for graphics and text In Bi D printing the print head prints in both directions Bi D is faster but the vertical alignment may not be as precise as Uni D When Auto is on the printer automatically switches between Uni D and Bi D as needed when data is received Font and Pitch Select the built in printer font and character pitch used as the default Normally you use your software to select the font and pitch The default Font and Pitch are Courier 10 cpi characters per inch Interface mode Determines from which interface the printer receives print data Auto default allows the printer to automatically switch as needed between the parallel and serial interfaces However if you experience communication problems you might want to set the interface mode to either Parallel or Option Option requires an optional interface card The printer will ignore data from the parallel interface Auto interface wait time Sets the time period 10 seconds default or 30 se
19. Sans Serif y y y y Horizontal tab positions Every eight characters EPSON Courier 4 y J Font selection Last font selected in Default Setting mode EPSON Prestige y y y Special printing effects Cancelled except condensed and economy EPSON Script J N N printing User defined character Hardware control panel initialization cleared Scalable fonts set Software initialization deselected only Minimum Maximum Fonts oint size oint size Increments EPSON Roman g 8 P 32 2 Control Panel EPSON Sans Serif 8 32 2 EPSON Roman T 3 32 5 The printer s control panel contains lights for displaying the EPSON Sans Serif H 8 32 gt printer status and buttons for controlling certain functions as Interface Specifications Data format Synchronization Handshake timing Signal level Connector Initialization 8 bit parallel IEEE P1284 compatible mode STROBE pulse BUSY and ACKNLG signals TTL compatible 36 pin Centronics connector or equivalent The printer can be initialized returned to a fixed set of conditions in these ways Hardware x The printer is turned on initialization The printer receives an INIT signal from the parallel interface pin 31 goes LOW Software Software sends the ESC initialize the printer initialization command the last panel settings are kept Control panel Hold down the Pause button and the Alt button the initialization last panel settings are kept All
20. and click OK Wait for the printer to print the pattern Confirming Alignment Sheet for the offset value you entered 7 Repeat steps 5 and 6 for each of the patterns that need to be aligned 8 When you finish click Quit 9 A dialog box opens reminding you to save the new settings by turning the printer off using the O perate button Settings will not be saved if you turn off the power to the printer with a wall switch or from a power strip Setting the Thickness Adjustment Lever Before you start printing check the thickness adjustment lever to make sure it is set correctly for the type of paper or media you are loading To access the lever open the printer cover the lever is in the right back corner as shown in the following illustration Ink Jet Printers 1 96 Use the table below to set the thickness adjustment lever for your media type If a document is smeared set the thickness adjustment lever to the position regardless of the paper type and print it again Caution Before you change the lever setting make sure there is no paper in the paper path and that printing is paused To do this press the Pause button or turn off the printer Thickness Thickness adjustment adjustment Media type lever position Media type lever position Standard paper 0 Envelopes Transparency film 0 Previously Labels 0 smeared 7 documents Continuous paper 0 Using Special Paper and Other Media
21. aning cycles to improve print quality To check the print quality print a demonstration page If the print quality does not improve after you clean the print heads three times and you are sure the cartridges are not low or out of ink see the next section contact your dealer or authorized EPSON servicer Replacing the Ink Cartridges The printer s Ink Out O black and Ink Out NNN color lights tell you when your ink cartridges are low on ink and when you need to replace them If one of these lights flashes the indicated cartridge is low on ink if it remains on you need to replace the cartridge C Caution Do not replace an ink cartridge unless its Ink O ut light tells you to If you replace a cartridge before its light flashes the sensor that tells you when ink is out will not work with the new cartridge Leave the old cartridge installed in the printer until you are ready to replace it with a new one Attempting to print without a cartridge installed can damage the printer If you replace a cartridge when the Data light is on you must turn off your printer and then turn it back on This erases the data received by the printer and you must resend your print job Once you install the ink cartridges do not open the clamp or remove the cartridges except to replace them with new ones Once you remove a cartridge you cannot reuse it When the color ink cartridge is empty you can continue printing with the black ink cartridge
22. artridge C Caution Do not remove the tape seal from the bottom of the cartridge otherwise ink will leak Lower the ink cartridge into its holder with the label facing up and the arrow pointing to the back of the printer Do not push down on the ink cartridge Press the ink cartridge clamp down until it locks in place You will feel some resistance C Caution Once you install the ink cartridge do not open the clamp or remove the ink cartridge except to replace it with a new one Otherwise the print head and cartridge may become unusable Once you remove a cartridge do not reuse it Reusing a cartridge that has been removed may damage the print head Press the Alt button again The Paus light flashes as the printer charges the ink delivery system and moves the carriage to its home far right position Even if you don t press Alt the printer moves the carriage back to its home position about 30 seconds after you install the cartridge C Caution The Paus light flashes for about 60 seconds while ink is being charged in the system Never turn off the printer while the Paus light is flashing this can result in incomplete charging of printer ink Close the printer cover When the charging cycle finishes the Pause light stops flashing and stays on Press the Pause button to turn off the light and resume printing If you want to check the print quality print a demonstration page Cleaning the Printer If you
23. artridge or the ink may dry up Warning The ink cartridge is a self contained unit Under ordinary use ink will not leak from a cartridge If ink gets on your hands wash them thoroughly with soap and water If ink gets into your eyes flush them immediately with water Lift up the ink cartridge clamp Then remove the protective sheet from the cartridge holder Open the ink cartridge package Next remove the tape seal from the top of the cartridge as shown C Caution Do not remove the tape seal from the bottom of the cartridge ink will leak out 1 96 3 Lower the cartridge into the print head unit with the label face up and the arrow mark pointing to the rear Do not push down on the ink cartridge 4 Press the ink cartridge clamp down until it locks in place You will feel some resistance C Caution Once you install the ink cartridge do not open the clamp or remove the ink cartridge except to replace it with a new one Otherwise the cartridge and print head may become unusable 5 Press the Alt button again to return the print head unit to its home far right position Even if you do not press Alt the printer moves the print head unit back to its home position about 30 seconds after you install the cartridge The first time you install the ink cartridge the printer automatically charges the ink delivery system and returns the print head unit to its home position This operation takes about tw
24. conds for the printer to wait for data from the current interface and accept no data from the other interface when you re using the Auto interface mode Software Specifies the printer control language to use when printing from DOS EPSON ESC P 2 default or IBM XL24E If your software allows you to select EPSON ESC P 2 choose it for the most advanced fonts and graphics Auto CR Specifies that the printer perform a carriage return and line feed operation if the print positions exceed the right margin of the paper Used in IBM XL24E mode only AGM Alternate Graphics Mode Specifies that the printer use high resolution 24 pin graphics commands Used in IBM XL24E mode only Character table Selects the set of characters and symbols that can be printed The default is the Italic U S A character table If you commonly use a language containing accents symbols or other characters not available in the Italic U S A character table change to a different character table Auto line feed Specifies that a carriage return character encountered in the print file be accompanied by a line feed command By default auto line feed is off If text lines print on top of one another turn on auto line feed Network interface mode If you re having trouble printing when the printer is connected to a network turn on network interface mode By default network interface mode is off 0 Slash Specifies whether the printer prints a slashed ze
25. d to change the printer s factory defaults turn on Default Setting mode and change the settings using the control panel buttons To turn on the Default Setting mode and print instructions turn off the printer Load paper in the printer Then hold down the Economy C ondensed button while you turn the printer back on Follow the instructions the printer prints to change the default settings by pressing the buttons on the control panel When you are finished press Pause and turn off the printer to exit Default Setting mode The printer functions are shown in the table below and described in the following paragraphs The default settings are in bold Setting Options Print direction Auto Bi D Uni D Font Roman Sans Serif Courier Prestige Script Roman T Sans Serif H Pitch 10 cpi 12 cpi 15 cpi 17 1 cpi 20 cpi Proportional I F mode Auto Parallel Option Auto interface wait time 10 seconds 30 seconds Software ESC P 2 IBM XL24E Auto CR Off On AGM Off On Character table PC437 PC850 PC860 PC861 PC863 PC865 Abicomp BRASCII Roman 8 ISO Latin 1 Italic International character set for Italic table Italic U S A Italic France Italic Germany Italic U K Italic Denmark 1 Italic Sweden Italic Italy Italic Spain Auto line feed Off On Network I F mode Off On 0 slash 0 0 Page length for continuous paper 11 inch 12 inch 8 5 inch 70
26. e 7 Adjust the rear edge guide to match the length of your paper When you load paper in the landscape direction wider than it is tall the rear edge guide may not match the length of your paper In this case remove the rear edge guide and re insert it as shown 8 Lower the output tray to the printing position Make sure that the rear edge guide of the paper tray is positioned under the output tray The rear edge guide must be under the output tray to allow room for the paper loaded in the sheet feeder and to prevent a paper jam Testing the Printer Before continuing test the printer to ensure it is functioning properly For the self test use paper that is at least 8 25 inches 210 mm wide If you load narrower paper the print head will spray ink directly onto the platen which could mar future printouts EPSON Stylus 1500 9 EPSON Stylus 1500 1 Press the Operate button to turn off the printer C Caution Never turn off the printer by unplugging it or switching off a power strip Always turn off the printer by pressing the Operate button 2 While holding down the Load Eject button press the Operate button to turn on the printer Wait for the paper to load then release the buttons The 360 dpi self test begins by printing in black ink on the first and last lines of the first sheet of paper to measure the page length Note If the self test does not begin turn off the printer and repeat step 2 You may n
27. eed to hold down the buttons a few seconds longer If you installed the color ink cartridge the self test prints in color If you want to run the 180 dpi self test turn on the printer while holding down the LF FF button The 180 dpi self test always prints in black 3 To end the self test press the Pause button If there is paper in the paper path press the Load Eject button to eject it Then turn off the printer Otherwise the test continues until the paper in the sheet feeder runs out Caution Do not turn off the printer before pressing the Pause button If the quality of the test output is not good clean the print heads Then print a demonstration page or another self test to check the print quality You may need to repeat these procedures several times to fully solve the problem You may also need to calibrate your printer After connecting the printer to your PC and installing the printer driver calibrate your printer using the calibration utility program that came with your printer Installing the Printer Driver A printer driver is software that allows your computer to control the printer You must install the printer driver included on the Windows or Macintosh driver diskette that came with your printer The driver diskette also contains two utilities the EPSON Spool Manager and Printer Calibration Utility When you install the printer driver they are automatically copied to your hard disk Note It is a good
28. from production date and up to 6 months after opening the package at 77 F 25 C Temperature Storage 4 to 104 F 20 to 40 C 1 month at 104 F 40 C 22 to 140 F 30 to 60 C 1 month at 104 F 40 C 120 hours at 140 F 60 C Freezing 29 F 6 C 1 7 inches W x 2 2 inches D x 1 5 inches H 42 9 mm W x 56 5 mm D x 38 5 mm H Transit Dimensions Ink cartridge life may vary If you often print large graphics and dense text with little white space you use ink faster than if you print pages with lots of white space The ink thaws in approximately 3 hours at 77 F 25 C C Caution Use only genuine EPSON ink cartridges and do not refill them Other products may cause damage to your printer that is not covered by EPSON s warranties Do not use an ink cartridge after the expiration date on the package Safety Approvals Safety standards UL 1950 with D3 CSA 22 2 950 with D3 EMC FCC part 15 subpart B class B Ink Jet Printers EPSON Stylus 1500 Mechanical Paper feed method Friction tractor feeder Paper path Sheet feeder front entry Manual feed slot rear entry Tractor feeder rear entry Sheet feeder 100 sheets at 17 Ib 64 g m paper capacity 70 sheets of EPSON coated paper 30 sheets of EPSON high quality glossy paper 50 sheets of transparency film 30 index cards 10 envelopes For oversized coated paper such as Super A3 B and A2 the sheet feeder ca
29. hes x 4 inches 102 to 406 x 102 mm minimum folding length Paper types Plain paper Thickness 0 065 mm to 0 1 mm Weight 52 g m to 82 g m Continuous labels Size Backing sheet 4 to 16 inches x 4 inches 101 6 to 406 4 x 101 6 mm minimum folding length Label sheet Minimum 2 5 x 0 9 inches 63 5 x 23 9 mm Paper types Plain paper Thickness Total thickness Maximum 0 2 mm Label thickness Maximum 0 12 mm Note Poor quality paper may reduce print quality and cause paper jams and other problems If you encounter problems switch to a higher grade of paper Print on coated paper high quality glossy paper envelopes and transparencies only under these normal conditions 59 to 77 F 15 to 25 C 40 to 60 RH Temperature Humidity High quality glossy paper can be stored at 20 to 60 relative humidity and 59 to 86 F 15 to 30 C Do not load folded or curled paper envelopes and transparencies EPSON Stylus 1500 2 Printable area Single sheets A BL BR A The minimum top margin is 0 12 inch 3 0 mm B The minimum left margin is 0 12 inch 3 0 mm For oversized paper this margin is 0 98 inch 25 mm for A3 landscape A2 portrait US B landscape and US C portrait and 0 2 inch 5 mm for B4 landscape The minimum right margin is 0 12 inch 3 0 mm For oversized paper this margin is 1 97 inches 50 mm for A3 landscape and A2 portrait and 2 44 inches 62
30. ies C Caution Turn off all virus protection programs before you install the printer software You do this by holding down the Shift key while you restart your Macintosh You must hold down the Shift key until the Welcome to Macintosh screen appears After installation you can restart the computer without pressing Shift to use the virus protection programs 1 Turn on your printer and your Macintosh 2 Insert the EPSON Macintosh driver diskette into a diskette drive 3 If necessary double click the Driver Disk icon to open the Driver Disk window EPSON Stylus 1500 11 EPSON Stylus 1500 4 Double click the README Ist icon in the Driver Disk window to read the latest information on your printer and its driver After you install the driver you can click the README Ist icon on your screen to read the file 5 Double click the Installericon to install the driver 6 When you see the initial screen click OK to continue You see the following screen Click the items you want to select Shift click to select multiple items Serial Driver Package Network Driver Package StylusColor AT StylusColor Epson Monitor2 Macintosh HD Bi D Calibration Utility Network Driver Package Size 1329K Date Mon Sep 11 1995 Version 2 0 2 This package contains the Stylus COLOR printer driver and i utilities for use in a network environment AT StylusCOLOR Epson Monitor2 Bi D Calibration Utility Epson
31. inuous paper from the tractor feeder and begins to print Paper Handling Problems This section describes how to prevent paper jams and ensure that paper feeds properly Paper jam problems If paper jams inside the printer frequently try the following Q Use a higher quality paper that is suitable for ink jet printers and is not too thin too thick or rough For best quality use EPSON coated and high quality glossy papers See Printer Specifications for paper specifications Q Fan the stack of paper before you load it EPSON Stylus 1500 16 O If you loaded plain paper try turning the stack over The printable side should be facing down 1 Do not load too many sheets in the sheet feeder See Printer Specifications for the sheet feeder capacity Paper feeding problems If paper does not feed properly the most likely causes are I Paper is curled or folded Use flat undamaged paper 1 The paper is of poor quality use a better quality paper 1 The paper is too thin or thick see Printer Specifications for paper size and type specifications 1 The paper was exposed to excess humidity See Printer Specifications for the required environmental conditions 1 The left edge guide is too tight or too loose adjust it for the size of the paper 1 The thickness adjustment lever is set incorrectly for the media see Setting the Thickness Adjustment Lever I Continuous paper may be in the paper
32. inute or so Wait until the EPSON folder and EPSON Printer Driver Setup confirmation screen appear Then click OK on the confirmation screen to exit the installation program Ink Jet Printers 1 96 EPSON Stylus 1500 The EPSON folder contains these icons EPSON Calibration Utility Spool Manager EPSON Stylus Help EPSON Stylus ReadMe 19 Calibrate your printer using the EPSON Calibration Utility The installation program automatically selects your printer driver as the default printer for Windows 95 applications and assigns the printer driver to port LPT1 If you need to change your default printer driver or the port assignment see your Windows 95 online help utility for instructions Installing a Driver for DOS Programs Most DOS software programs include drivers for EPSON ESC P 2 printers If the Stylus 1500 driver is not listed in your software choose the first printer available in the lists below Also check with your software manufacturer to see if a Stylus 1500 driver is available When printing black and white only select Stylus 1000 Stylus 800 800 LQ 870 1170 LQ 570 1070 SQ 870 1070 LQ 850 LQ 500 When printing in color as well as black and white select LQ 860 LQ 2550 DLQ 3000 Note These drivers let you use your printer but do not support some features such as 720 dpi and MicroWeave Installing the Macintosh Printer Driver Follow these steps to install the Macintosh driver and utilit
33. nter using the Chooser EPSON Stylus 1500 12 Calibrating the Printer Your printer has been calibrated at the factory so that vertical lines in your text and graphics are properly aligned If you notice misaligned images in printouts however you can calibrate the printer with the EPSON Printer Calibration Utility Calibrating with a PC Note If you cannot use the calibration utility program you can use the printer adjustment mode to calibrate your printer Follow these steps 1 Double click the EPSON Printer Calibration icon in the EPSON group 2 Click OK at the next screen to start the calibration program 3 Select EPSON Stylus 1500 as the printer Select which print head black or color to calibrate Then click Next 4 Select the port the Stylus 1500 is connected to Then click Next 5 Make sure the printer is on and letter size paper is loaded then click Next The Current Alignment Sheet is printed 6 Select the patterns that are misaligned then click Next Note Only patterns 2 3 and 4 are selectable Do not select pattern 1 For each pattern you selected the printer prints a Test Alignment Sheet of multiple vertical lines In most samples the vertical lines are slightly misaligned Look for the sample that is most closely aligned Aligned Not aligned 7 Enter the number of the sample that is aligned or select Not aligned if none of the samples are aligned Then click Next 8 If
34. o minutes to complete Caution During the ink charging process the Pause light flashes Never turn off the printer while this light is flashing In order to maintain optimum print quality the printer periodically performs a cleaning operation You may notice the cleaning cycle being performed when the printer has been on for a while without being used or when you turn on the printer after it has been off for a while Ink Jet Printers Loading Plain Paper in the Sheet Feeder You can load up to 100 sheets of plain paper Always load paper with the printable surface facing down The printable surface is marked with an arrow on most paper packaging 1 Make sure the paper release lever is set to the single sheet position 3 Slide the right edge guide to the left as far as it will go Slide the left edge guide to match your paper s width 4 Move the center support midway between the edge guides Then gently extend the rear edge guide until it stops Ink Jet Printers EPSON Stylus 1500 5 Fan a stack of paper then tap it on a flat surface to even the edges 6 Load the stack of paper into the sheet feeder Make sure the right edge of the stack is against the right edge guide Slide the left edge guide against the left edge of the paper Note The sheet feeder can hold up to 100 sheets of 17 lb 64 g m plain paper Do not load paper above the arrow mark which is located on the inside surface of the edge guid
35. pacity is 30 sheets Total print volume 75 000 pages A4 text Dimensions Width 26 1 inches 664 mm Depth storage 19 8 inches 504 mm Depth printing 24 4 inches 619 mm maximum Height 8 0 inches 202 mm Weight 24 9 Ib 11 5 kg without ink cartridges Electrical Input voltage range 103 5 to 132 V Rated frequency range 50 to 60 Hz Input frequency range 49 5 to 60 5 Hz Rated current O7A Power consumption Approx 23 W during self test LQ at 10 cpi Environmental Temperature Operation 50 to 95 F 10 to 35 C Storage 4 to 140 F 20 to 60 C 1 month at 104 F 40 C 120 hours at 140 F 60 C Humidity Operation 20 to 80 RH Storage 5 to 85 RH without condensation Stored in shipping container Fonts The printer comes with an installed set of fonts which are selectable using the Default Setting mode However the printer always uses the fonts you select with your software program The only time you need to select the printer s installed fonts is when your software program does not allow you to select fonts You can select other font and pitch combinations using ESC P 2 commands EPSON Stylus 1500 3 EPSON Stylus 1500 Bitmap fonts Item Default setting Fonts 10 cpi 12 cpi 15 cpi Proportional Character pitch Last font selected in Default Setting mode EPSON Roman y y y y Vertical tab position Cleared EPSON
36. path when you print from the sheet feeder Remove the continuous paper 1 The paper release lever is set to the wrong position see Switching Between Continuous Paper and Single Sheets 1 Too many sheets are loaded in the sheet feeder See Printer Specifications for the sheet feeder capacity Printer Care Cleaning the Print Heads The printer periodically cleans its print heads automatically so normally you should not need to manually activate a cleaning cycle However the ink nozzles in the print head may become clogged occasionally and reduce the print quality If this happens you can run a cleaning cycle to clear the nozzles You can clean one or both print heads Each cleaning cycle takes about one minute During the cleaning cycle the carriage moves back and forth and you can hear the printer recharging the print heads The Pause light flashes throughout the cleaning cycle and then stays on when the cycle is finished To clean the black print head 1 Make sure the printer is on and press the Pause button 2 Hold down the Alt button and press LF FF The cleaning cycle begins 3 Press the Pause button to resume printing Ink Jet Printers To clean the color print head 1 Make sure the printer is turned on and press the Pause button 2 Hold down the Alt button and press Load Eject The cleaning cycle begins 3 Press the Pause button to resume printing It can sometimes take up to three cle
37. per and glossy paper within one year of purchase Use transparencies within six months I Do not touch the printable surface of the paper hold the sheets by their edges The moisture and oils on your hands can reduce print quality EPSON Stylus 1500 13 EPSON Stylus 1500 QO After printing on high quality glossy paper or transparencies remove each sheet from the output tray immediately Make sure each sheet is dry before stacking 1 Return unused sheets and envelopes to their original package as soon as possible after you finish printing Keep the paper wrapped and store flat in a dry protected area Unfavorable storage conditions especially high temperature humidity and direct sunlight can damage the media Loading Coated or Glossy Papers and Transparencies Use the same procedure described in Loading Plain Paper in the Sheet Feeder to load coated or glossy papers and transparencies in the sheet feeder You can load up to the following number of sheets QO 70 sheets of coated paper However if you load legal size or oversize coated paper for 360 or 720 dpi do not load more than 30 sheets and make sure the paper does not reach more than halfway to the arrow mark on the inside of the edge guide L 50 sheets of transparency film T 30 sheets of high quality glossy paper Note Use only EPSON transparency film and high quality glossy paper Remember to change the printer driver settings so they are
38. rectly behind the printer so that paper can feed smoothly Make sure the paper path is not obstructed and allow enough room for printed pages to be stacked in front of the printer 2 Move the paper release lever to the continuous paper position Note If a single sheet is in the paper path press the Load Eject button to eject it before moving the paper release lever 3 Hold the manual feed guide with both hands and gently lift it up and off the printer 4 Release the sprocket units on the tractor by raising the sprocket lock levers 5 Move the sprocket units to match the paper s width then position the center support midway between the two sprocket units Ink Jet Printers 6 Open both sprocket covers 7 Make sure the printable side of the paper is up Then fit the first four holes of the paper over the sprocket pins and close the sprocket covers 8 Position the left sprocket unit so its right edge is aligned with the arrow mark on the printer The arrow mark indicates the left edge of the printable area Then lower the sprocket lock lever to lock the left sprocket unit 9 Slide the right sprocket unit to remove any slack in the paper Then lower the sprocket lock lever into place 10 Reattach the manual feed guide to the printer Match the holes of the guide to the pins on both sides of the printer and push until they click into place Ink Jet Printers EPSON Stylus 1500 11 Lower both page
39. ro or unslashed zero 0 This feature is useful for clearly distinguishing between an uppercase letter O and a zero Page length for continuous paper Available only when you use continuous paper with the tractor feeder You can set the paper length to 11 default 12 8 5 or 70 6 the length of A4 paper inches Ink Jet Printers Skip over perforation Selects whether or not the printer skips over the perforations of continuous paper providing a 1 inch margin between the last line printed on one page and the first line printed on the next Because most software programs set their own top and bottom margins use this feature only if your program does not provide them This feature does not affect single sheet paper Auto tear off When using continuous paper advances the paper perforation to the tear off position where you can easily tear off the printed pages When the printer receives data it automatically reverses the paper to the top of form position and starts printing so you can use all of the next sheet C Caution When you use the tractor to print on labels set this feature to off Otherwise labels may come off the backing and jam the printer Print mode Selects the paper type you plan to use Use this feature to select paper types only when printing from a DOS application Select Plain paper true black when printing text on plain paper Select Plain paper composite black for color images on plain paper or when
40. t LPT1 Installing the Driver for Windows 95 Follow these steps to install the printer software for Windows 95 First you ll install the driver using the Windows 95 plug and play capabilities then you ll run the EPSON Printer Driver Setup program to install the printer driver utilities and create an EPSON folder on your hard disk Note If you originally installed the Stylus 1500 driver under Windows 3 1 you must reinstall the driver under Windows 95 1 Make sure plain paper is loaded and the printer is connected to the computer s parallel port The paper is used to perform a test print in step 12 2 Turn off the printer and your computer if necessary Ink Jet Printers 10 11 12 13 14 15 16 17 18 Turn on the printer first then turn on the computer Your computer begins loading Windows 95 If you defined a password in Windows 95 enter it at the prompt You see the New Hardware Found screen Your printer model name is displayed on the screen Select the Driver from disk provided by hardware manufacturer button Do not select any other buttons Click OK You see the Install From Disk screen Insert the Windows printer driver diskette that came with your printer in a diskette drive If you inserted the diskette in drive A click OK Otherwise change the drive letter in the Copy manufacturer s files from box and click OK You see the Select Device screen Make sure your printer model
41. the black ink in a printed image is blurred Composite black is produced by mixing cyan magenta and yellow inks Select Exclusive paper for coated paper and high quality glossy paper Select Transparency when printing on transparencies When Transparency is selected printing is unidirectional Banner paper Specifies that banner paper is not recognized as single sheet paper even if the paper release lever is set to the single sheet position Paper is not ejected and advanced forward to the next page with the LF FF button Removing the Protective Materials You must remove all protective materials packed around and inside your printer before you set it up and turn on the power Save all packaging and protective materials in case you need to transport the printer in the future The printer should always be transported in its original packaging or equivalent materials Installing the Black Ink Cartridge Follow the steps in this section to install your printer s black ink cartridge W Warning The ink cartridge is a self contained unit Under ordinary use ink will not leak from a cartridge If ink gets on your hands wash them thoroughly with soap and water If ink gets into your eyes flush them immediately with water C Caution Do not open the ink cartridge package until just before you install the cartridge or the ink may dry up Ink Jet Printers N Pe EPSON Stylus 1500 Make sure the printer is turned on Remove
42. the ink compartment cover as shown Remove the ink cartridge from its package Insert the end of the cartridge with the foil plug into the ink compartment following the instructions on the cartridge Push the cartridge all the way into the compartment You will feel some resistance When the cartridge is correctly installed the Ink Out O light goes off Note If the Ink Out O light remains on the ink cartridge may not be installed correctly Remove it and then reinsert it as described above Reattach the ink compartment cover as shown The first time you install the ink cartridge the printer automatically charges the ink delivery system This takes about two minutes EPSON Stylus 1500 7 EPSON Stylus 1500 Caution During the ink charging process the Pause light flashes Never turn off the printer while the Pause light is flashing Also never remove the ink cartridge while ink is being charged in the system When you need to replace ink cartridges be sure to use only genuine EPSON ink cartridges and do not refill them Other products may cause damage not covered by EPSON s warranty Installing the Color Ink Cartridge Follow the steps in this section to install your printer s color ink cartridge C 1 2 EPSON Stylus 1500 8 Caution Do not remove the color print head If you remove it it may become unusable Do not open the ink cartridge package until just before you install the c
43. to the button functions explained below you can perform additional functions using certain button combinations and power on sequences Alt Hold down this button for about five seconds to move the carriage to the color ink cartridge replacement position The Pause light begins flashing Press the Alt button again to return the carriage to its home position See Replacing the Color Ink Cartridge This button is also used in combination with other buttons to reset the printer or clean the print heads see the next section for more information Pause or Reset Stops printing temporarily Press it again to resume Hold down this button for about three seconds to enter micro adjust mode Economy Condensed or Cleaning 0 Selects economy or condensed mode as indicated by the Economy and Condensed lights Use this button only if you print from a DOS application LF FF Press this button briefly to feed paper line by line Hold it down to load a single sheet or to advance continuous paper to the next top of form position Font Press this button until the combination of lights indicates the font of your choice Use this button only if you print from a DOS application Micro Adjust D Micro Adjust U Adjusts the loading position or tear off position for continuous paper while in micro adjust mode Press the Micro Adjust D button to advance paper forward or press Micro Adjust U to feed paper backward To enter micro adjust mode
44. ze Paper types Thickness Paper weight Envelopes Size Paper types Thickness Paper weight Index cards Size Paper types Thickness Weight Single sheet labels Size Paper types Total thickness Letter 8 5 x 11 inches A4 210 x 297 mm A2 420 x 594 mm Super A3 B 13 x 19 inches A3 297 x 420 mm US B 11 x 17 inches US C 17 x 22 inches B4 250 x 353 mm B5 176 x 250 mm Legal 8 5 x 14 inches Statement 8 5 x 5 5 inches Executive 7 5 x 10 inches Plain paper and EPSON s coated paper and high quality glossy paper 0 0025 to 0 004 inch 0 065 to 0 11 mm Sheet feeder 17 to 24 lb 64 to 90 g m Manual feed slot 14 to 24 Ib 52 to 90 g m No 10 9 5 x 4 1 inches 241 x 104 mm DL 8 7 x 4 3 inches 220 x 110 mm C5 9 0 x 6 4 inches 229 x 162 mm Plain bond or air mail paper 0 006 to 0 02 inch 0 16 to 0 52 mm 12 to 24 Ib 45 to 90 g m A6 105 x 148 mm Plain paper 0 21 mm 188 g m Letter 8 5 x 11 inches A4 210 x 297 mm Plain paper Use labels that completely cover the backing sheet Maximum 0 2 mm EPSON Stylus 1500 1 EPSON Stylus 1500 Transparencies Size Letter 8 5 x 11 inches A4 210 x 297 mm Thickness 0 075 to 0 085 mm Banner paper Size 8 3 to 17 inches x 16 4 feet 210 to 432 mm x up to 5 m Paper types Plain paper Thickness 0 08 mm to 0 1 mm Weight 17 to 22 Ib 64 g m to 82 g m Continuous paper Size 4 to 16 inc
Download Pdf Manuals
Related Search