Electrolux 65320 K Cooktop User Manual
Contents
1. be selected as required 24 Cleaning and Care Cleaning and Care Ceramic glass cooking surface AN cm 1 It is important to clean the cooking surface after each use Important Never use aggressive cleaners such as for example coarse scouring cleaners or pan cleaners that scratch Always clean the cooking surface after each use Use a damp cloth and a little washing up liquid Then rub the cooking surface dry with a clean cloth No residues of cleaner must be left on the surface Clean the entire cooking surface thoroughly once a week For cleaning use Stahl Fix or Vitroclen Then rinse the entire cooking surface with plain water and rub it dry with a clean cloth Ensure that no remnants of cleaner are left on the surface Otherwise the cooking surface will be damaged Only use the recommended cleaners 25 Cleaning and Care Stubborn Soilage 26 Residues from food that has boiled over First soften these using a wet cloth and then remove residues using a glass scraper Caution Take care when using a glass scraper Then clean the cooking surface with the recommended cleaners Sugar Warning Remove burnt on sugar or melted plastic immediately when still warm not hot using a glass scraper otherwise damage may be caused to the hob Then clean the cooking surface normally Damage from sugar or food containing Sugar can be avoided by polishing the cooking surface with2. heat setting chosen the functions that are activated and any heat remaining in the cooking zone Lock Button in addition the appliance is fitted with a lock button The control panel can be completely locked using this button In this way Inadvertent changes to the settings are prevented e Automatic Function your appliance is equipped with an electroni cally controlled automatic warm up function on all four cooking zones he built in function switches automatically from the maxi mum heat setting to the lower heat setting selected for further cook Ing Safety Switch a safety switch automatically switches off all the cooking zones when no changes have been made to the settings for a set period of time Keep Warm Setting 1 is the heat setting at which food can be kept warm Residual Heat Indicator an 4 illuminates in the display if the cook ing zone is sufficiently hot to cause burns e Multipurpose Cooking Zone the VITRAMIC cooking surface is equipped with a multipurpose casserole zone Depending on the set ting it can be used as a round or oval cooking zone e Triple Ring Cooking Zone in addition the cooking surface has a tri ple ring cooking zone This enables you to save energy The Key Features of Your Appliance e Timer all four rings can be automatically switched off using the integrated timer When the end of the cooking time has been reached the cooking zone switches off Appliance Description 65
3. Vitroclen Cleaning and Care Spots Scale shiny pearl like spots metallic iri descent coloured spots and food rem nants from pans that have formed during cooking are best removed when the cooking zones are still warm Use the cleaners and polishes recom mended If necessary clean more than once Acids Important Do not put vinegar lemons or scale removers on the hob frame they will make the surface matt Grains of sand that have fallen on the cooking surface can cause scratching when pans are slid Therefore make sure that no grains of sand are left on the cooking surface Abraded decor Important If aggressive cleaners or pans with abrasive bases are used then the decor will take on an abraded appearance and dark spots will appear over time You can obtain suitable cleaners and polishes as well as glass scrapers from AEG Service Force Centre 27 What to do if What to do if A fault may have been caused by a minor operating error which you can correct yourself with the help of the following instructions Do not attempt any further repairs if the following instructions do not help in each specific case AN Warning Repairs to the appliance should only be carried out by approved service engineers Improper repairs can cause injury or mal function If your appliance needs repairing please contact your local AEG Service Force Centre What to do if the cook
4. any traces left from manufacturing Important Do not use any caustic abrasive cleaners The surface could be damaged Operation of the Cooking Surface TOUCH CONTROL sensor buttons To operate the TOUCH CONTROL sensor buttons place your finger flat on the desired button until the corresponding indicator illuminates or extinguishes or the desired function is performed For quicker adjustment leave your finger on the button until the desired value is reached All entries are acknowledged by an acoustic signal Switching on the appliance Switch on the appliance using the mains On Off button The Heat Setting Residual Heat display fields indicate After the mains On Off button has been operated to switch on your appliance one of the cooking zones must be selected using the cooking zone selection buttons within approx 10 seconds Otherwise the appli ance switches off again for safety reasons Switching off the appliance Operate the mains On Off button to completely switch off the appli ance After the individual cooking zones or the entire cooking surface have has been switched off the presence of residual heat is indicated by as in Hot in the Heat Setting Residual Heat display fields of the respective cooking zones If all cooking zones are switched off the appliance switches off auto matically after a period of time Um 1 Operation of the Cooking Surface Cooking with the automatic warm
5. made even during the guarantee period What to do if SERVICE AND SPARE PARTS In the event of your appliance requiring service or if you wish to pur chase spare parts contact your local AEG Service Force Centre by tele phoning 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area Please ensure that you have read the section What to do if as the engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty Please note that proof of purchase is required for in guarantee service calls Help us to help you Please determine your type of enquiry before writing or telephoning When you contact us we need to know e Your name e Address and post code e elephone number e Clear and concise details of the fault e Name and model of the appliance e E number This information can be found on the rating plate Customer Care For general enquiries concerning your AEG appliances or for further information on AEG products please contact our Customer Care Department Customer Services Department AEG Domestic Appliances 55 77 High Street Slough Berkshire SLI ID2 Tel 08705 350 350 31 32 What to do if GUARANTEE CONDITIONS Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance Ihe guarantee is valid for 12 months commencing
6. repairs can cause injury or significant mal function If your appliance needs repairing please contact your local AEG Service Force Centre e f your appliance malfunctions or fractures cracks or splits appear switch off all cooking zones Disconnect the hob from the electricity supply Child Safety The cooking zones will become hot when you cook Therefore always keep small children away The hob is designed to be operated by adults Do not allow children to play near or with the hob Safety During Use e his appliance may only be used for normal cooking and frying in the home It is not designed for commercial or industrial purposes e Do not use the hob to heat the room e ake care when plugging electrical appliances into mains sockets near the hob Connecting leads must not come into contact with the hot surface e Overheated fats and oils catch fire quickly You should supervise cooking when preparing foods in fat or oil e g chips e Switch the cooking zones off after use Safety Safety When Cleaning e For safety reasons do not clean the appliance with a steam jet or high pressure cleaner e Clean the hob in accordance with the maintenance and cleaning Instructions in this manual How to Avoid Damage to Your Appliance e Do not use the hob as a work surface or for storage e Do not use the cooking zones with empty pans or without pans e Ceramic glass is insensitive to temperature shock and very
7. up function e__e L I Ju AIT four rings on the cooking surface have nine heat settings and are equipped with an automatic warm up function 1 lowest heat setting 4 highest heat setting 8 automatic warm up function Using the button select the heat setting that you require for cook ing once the pan is hot the cooking zone operates for a set period of time at full power 4 automatic warm up function and then switches back to the heat setting selected for further cooking The duration of the automatic warm up period is dependant on the set ting chosen for further cooking once the pan is hot Select the desired cooking zone using the cooking zone buttons The decimal point in the associated display field illuminates Press the H button for the required cooking setting to 8 he cooking setting chosen is then displayed After 5 seconds appears again in display instead of the cooking setting The cooking setting is displayed again at the end of the automatic warm up time 15 16 Operation of the Cooking Surface c 1 Press the 44 and buttons simultaneously to switch off Um 1 If you select a higher setting when the automatic function is in opera tion e g from 3 to 5 the previous warm up time is taken into account If you select a lower setting then the automatic warm up function is brought to an immediate end If you start cooking again on a cooking zone
8. when the appliance is handed over to the first retail purchaser which must be verified by purchase invoice or similar docu mentation The guarantee does not cover commercial use Ihe guarantee covers all parts or components which fail due to faulty workmanship or faulty materials The guarantee does not cover appliances where defects or poor per formance are due to misuse accidental damage neglect faulty installation unauthorised modification or attempted repair commercial use or failure to observe requirements and recommendations set out in the instruction book his guarantee does not cover such parts as light bulbs removable glassware or plastic Should guarantee repairs be necessary the purchaser must inform the nearest customer service office manufacturer s service or authorised agent AEG reserves the right to stipulate the place of the repair i e the customer s home place of installation or AEG workshop Ihe guarantee or free replacement includes both labour and materials Repairs carried out under guarantee do not extend the guarantee period for the appli ance Parts removed during guarantee repairs become the property of AEG The purchaser s statutory rights are not affected by this guarantee European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you f
9. 320 K Appliance Description 65320 K Cooking zone dimensions rear left 145 mm rear right 170 265 mm front left 120 170 210 mm front right 145mm 10 Appliance Description 65320 K Control panel 65320 K i DL rri mn ayn Pret 2 i TIMER Mains On Off button For switching on the appliance The appliance is switched on when the button is touched for approx one second switched off when the button is touched again for one second When the appliance is switched on the Heat Setting Residual Heat displays illuminate Cooking zone selection Buttons for choosing the cooking zone for which the settings are to be changed The decimal point is illuminated in the display field of the cooking zone just selected Heat Setting Residual Heat display The four display fields that are assigned to the four cooking zones dis play after switching on and when automatically switched off by the safety function to 4 depending on the heat setting chosen 8 when the warm up function is active 4 in the case of residual heat F in the case of a fault 11 12 Appliance Description 65320 K Heat setting selection and For setting and adjusting the heat setting 1 to 4 for the selected cooking zone or when in timer mode to set or change the required cooking time he heat setting or the cooking time is increased using the but ton and the automa
10. 65320 K Ceramic Glass Hob User Instructions Dear customer Please read these operating instructions through carefully Above all please observe the Safety section on the first few pages Please retain these operating instructions for future reference Pass them on to any subsequent owners of the appliance The warning triangle and or specific words Warning Caution Important are used to highlight information that is important for your safety or the function of the appliance It is imperative that this information is observed This symbol guides you step by step through the operation of the appli ance Next to this symbol you will find additional information and practical tips on using the appliance Tips and information about the economical and ecological use of the machine are marked with the clover In the event of a malfunction these operating instructions contain information on how to rectify faults yourself see the What to do if section If you require further assistance please contact your local AEG Service Force Centre see the section Service and Spare Parts Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Contents CONTENTS Disposal SE CPP Ct The Key Features of Your Appliance Appliance Description 65320 K Control panel 65320 K aa Mains On Off bu
11. ags inside e gt PS lt for polystyrene foam e g as used for the packing pieces com pletely free of CFCs The cardboard is made from 80 recycled paper Disposal of old appliances All old appliances must be properly disposed of with due regard to safety and the environment Warning Before disposing of old appliances make them inoperable Cut off the mains cable Information on disposal e The appliance must not be disposed of in the household rubbish e You can obtain information about collection dates or public tips from your local refuse department or council The Key Features of Your Appliance The Key Features of Your Appliance e Ceramic glass Cooking Surface the appliance has a VITRAMIC cooking surface made of glass ceramic and 4 fast heating cooking zones The particularly powerful radiant heater elements significantly shorten the amount of time taken for the zones to heat up Sensor Buttons your appliance is operated using TOUCH CONTROL sensor buttons Cleaning the advantage of the glass ceramic cooking surface and the sensor buttons is their ease of cleaning A wipe with a damp cloth is often all that is required See Section Cleaning and Care Mains button the appliance has a separate mains button The On Off button enables the electricity supply to the appliance to be com pletely switched off at the touch of a button Displays digital displays and indicators provide information on the
12. ant then the covering may distort or come loose In respect of fire protection the appliance corresponds to type Y EN 60335 2 6 Only this type of appliance may built into positions with a high cupboard or wall on one side The cooking surface must have a heat protective base permanently fixed in position The distance from the base to the underside of the cooking surface must be at least 50 mm The edges of the cut out must be coated with a water proof material The cooking surface must be built in such that the TOUCH CONTROL control panel is at the front see Fig 35 Installing and Connecting Up The separation between the hob and the extractor hood must be at least as large as that given in the extractor hood installation instruc tions 36 Installing and Connecting Up e On tiled work surfaces the joints in the area where the hob sits must be completely filled with grout e On natural stone synthetic stone or ceramic surfaces the snap action springs can be bonded in place e Ensure that the seal is correctly seated in the frame and that it Is seated against the work surface without leaving any gaps Please do not apply additional silicon sealant this will make removal more dif ficult in the event of the need for service 37 Installing and Connecting Up Electrical connection Assembly and connection of the new appliance may only be performed by an approved in
13. ck button again until the indicator extinguishes Operation of the Cooking Surface Locking unlocking the control panel At any time during the cooking process the control panel can be locked with the exception of the On Off button By this means acci dental changes to the settings can be prevented This function is also useful as a child safety measure Touch the 5 button until the indicator illuminates Child safety If lock button is active when the cooking surface is com pletely switched off by touching the mains button when the cooking surface is switched on again the lock button is active This means that the lock button must be operated first before the rings can be switched on again 17 18 Operation of the Cooking Surface Um 1 Timer function Setting changing the cooking time Select the desired cooking zone using the cooking zone selection but tons and set the desired heat setting Press the Timer button to activate the timer function for this cooking Zone Using the 4 or buttons set or change the amount of time required until the cooking zone is to switch off automatically e g 20 minutes The timer starts after a few seconds and indicates the amount of time left The small Timer Active indicator is also illuminated for the respective cooking zone e g the upper left indicator corresponds to the rear left cooking zone At the end of the cooking time set the co
14. ee Tips for cooking with and without the automatic warm up function Contents Cleaning and Care users 25 Ceramic glass cooking surface 25 SUDDO SON BEBE nes eura iy r ates ee tr oser 26 What todo ifia aise ane in 28 Service and Spare Parts u 12 ie 31 Customer Care anna EIS ERETI Pa cee 34 31 Guarantee Conditions 32 Installation Instructions 33 TECHNICA DACA suas nd done E ERO ea arts ehe ir am etus 33 Regulations Standards Directives 34 Installing and Connecting Up 35 fici 22a MH 35 Electrical eDHne el lOWd quada acne sach t EPiLRISRGCREe2ICSIQUXTeE PIX 38 Safety OPERATING INSTRUCTIONS N Safety The safety aspects of this appliance comply with the accepted technical standards and the German Appliance Safety Law However we also consider it our obligation as a manufacturer to make you aware of the following safety information Electrical Safety e he new appliance may only be installed and connected up by quali fied personnel according to the manufacturers instructions and to the relevant country standards Please observe this instruction otherwise the warranty will not cover any damage that may occur e Repairs to the appliance should only be carried out by approved serv ice engineers Improper
15. g zone 2300 W Rear left cooking zone 1200 W Rear right cooking zone 2400 W Front right cooking zone 1200 W Heater Element Voltage 230 V 240 V Total Electrical Load Max 7 1 kW Fuse Rating 30 Amp 33 Regulations Standards Directives Regulations Standards Directives This appliance meets the following standards e EN 60 335 1 and EN 60 335 2 6 in respect of the safety of electrical appliances for household use and similar purposes and e DIN 44546 44547 44548 in respect of properties of electrical cookers for the household e EN 55014 2 VDE 0875 part 14 2 e EN 55014 VDE 0875 part 14 12 93 e EN 61000 3 2 VDE 0838 part 2 e EN 61000 3 3 VDE 0838 part 3 in respect of basic electromagnetic compatibility EMC requirements C This appliance complies with the following EC directives e 73 23 EWG dated 19 02 1973 Low Voltage Directive e 89 336 EWG dated 03 05 1989 EMC Directive including Amendment Directive 92 31 EWG 34 Installing and Connecting Up Installing and Connecting Up Installing AN Important The new appliance is only to be installed and connected up by an approved installer Please observe this instruction otherwise the warranty will not cover any damage that may occur The veneer or plastic coverings on kitchen units around the appliance must be bonded with heat resistant adhesive 100 C If plastic cover ings or the adhesive are not sufficiently temperature resist
16. ing zones do not work c Check whether the mains fuse fuse box is intact If the fuse blows several times please call an approved electrician that the appliance is correctly connected and is switched on indicators on the control panel illuminate the corresponding cooking zone is switched on the cooking zones are set to the desired heat setting for cooking see section Cooking the cooking zones have been switched off by the safety switch see section Safety Functions the cooking zones cannot be switched on cs Check whether the control panel is locked see section Locking Unlocking the Control Panel more than 10 seconds have elapsed between operating the On Off button and switching on the desired cooking zone see section Switching on the Appliance the touch switches are partially covered by a damp cloth or liquid 28 sam What to do if the cooking zones do not heat up even though the displays are working Check whether demonstration mode has been activated accidentally To deactivate this mode ensure that the appliance is switched off and that the control panel is not locked Then proceed as follows Switch on main button Within 10 seconds press the following buttons simultaneously for a maximum of one second Lock button Cooking zone selection button front left Cooking zone selection button rear left When the buttons are released a peep tone so
17. irst purchased your product The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products This guarantee relates to you and connot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organ isation is aware of your move and able to look after you and your appliances France Senlis 33 0 44 62 29 29 Germany N rnberg 49 0 911 323 2600 Italy Pordenone 439 0 1678 47053 Sweden Stockholm 46 0 8 738 7910 UK Slough 44 0 1753 219899 Technical Data INSTALLATION INSTRUCTIONS AN Important This appliance must be installed by qualified personnel according to the manufacturer s instructions and to the relevant British Standards Please observe this instruction otherwise the warranty will not cover any damage that may occur Technical Data Appliance Dimensions Width 570 mm Depth 500 mm Height 55 mm Cut Out Dimensions Width 560 mm Depth 490 mm Corner radius R3 Power Consumption Front left cookin
18. nctions Timer and Egg Timer simultaneously Cooking zone safety switch Automatic pan sensing Pan and triple ring sensing is automatically activated when the cooking zone Is switched on If a cooking zone button is pressed but there is not a suitable pan on the cooking zone or the pan is too small Fault appears in the dis play This is also displayed in the case of overheating faults in the elec tronics or for safety reasons Automatic triple ring sensing The outer or middle ring is switched on or is switched off depending on the size of the pan A N Cooking zone safety switch If after a set period of time one of the rings is not switched off or the heat setting not changed the cooking zone switches off automatically or 4 appears in the displays of all the rings that are switched on he rings are switched off at e Heat setting 1 2 after 6 hours e Heat setting 3 4 after 5 hours e Heat setting 5 after 4 hours e Heat setting 6 9 after 1 5 hours Resetting the safety switch D il To reset the safety switch on all cooking zones switched on switch the appliance off and on again at the main button The cooking zones are then ready for use again appears in the ring display when there is still heat remaining Before Using for the First Time Before Using for the First Time Cleaning for the first time AN Wipe the ceramic glass cooking surface with a damp cloth to remove
19. oking zone switches off auto matically and an acoustic signal sounds Touch the TIMER button to switch off the signal and the indicator For quicker adjustment leave your finger on the H or button until the desired value is reached If the button is operated first the time setting starts at 99 minutes If the button is operated the time setting starts at 1 minute Use of the timer as an interval timer egg timer Press the Timer button to activate the timer function Using the or buttons set the required cooking time e g 20 minutes The timer starts after a few seconds and indicates the amount of time left When the time set Is at an end an acoustic signal sounds Touch the TIMER button to switch off the signal Displaying the remaining cooking time Select the desired cooking zone using the cooking zone buttons If the selected cooking zone is in timer mode the remaining cooking time appears in the Cooking Time display field Operation of the Cooking Surface Um 1 c 1 Touch the Timer button again Touch the HH and buttons simultaneously Ending the timer function early Cn rv Due a e i here are two ways of switching off the timer early Switching off the cooking zone and timer simultaneously Select the desired cooking zone using the cooking zone buttons If the selected cooking zone is in timer mode TIMER indicator illumi nated the
20. ramic items pans with uneven bases pans with a base less than 12 cm in diameter If you would nevertheless like to use the above mentioned pans you can disable automatic pan and triple ring sensing Switching off automatic pan and triple ring sensing Touch the desired cooking zone button on the button and within 10 seconds touch the cooker zone selection button for the desired cooking zone An acoustic tone confirms the entry Um 1 Operation of the Cooking Surface Switching on and off the triple ring or casserole zone when pan and triple ring sensing is switched off Select the cooking zone using the appropriate cooking zone selection button and set the desired heat setting Press the Triple Ring Zone Casserole Zone button The middle ring is switched on The indicator under the Il symbol illu minates The outer ring is switched on by pressing the button again The indica tor under the Ill symbol illuminates To switch off the outer ring press the Triple Ring Zone Casserole Zone button the outer ring is switched off The middle ring is switched off by pressing the button again After the cooking zone has been switched off pan and triple ring sens ing is automatically reactivated 21 22 Tables and Tips Tables and Tips Pans AN The better the pan the better the results e You can recognise good quality pans by the base of the pan e The base should be as thick and fla
21. re heated up at a high setting and do not need to be continually watched when cooking e dishes that are put in a hot frying pan The automatic warm up function is not suitable for e goulash and similar braised dishes that need continual turning until browned correctly liquid adding and then braising until cooked e dumplings pasta dishes with large amounts of liquid e cooking with pressure cookers e very large quantities of soup stew with more than 2 litres of liquid General notes e When cooking without the automatic warm up function we recom mend the use of a high heat setting to warm up the food using the button and then leaving the dish to finish cooking at an appro priate lower heat setting e You can use the heat setting for keeping food warm e ake note of the results when you initially use the appliance You can then decide which heat setting is the best for your dishes in the quantities you are accustomed to preparing with your pans You will then rapidly come to value the merits of the automatic function and will feel at ease with you new cooking surface 23 Tables and Tips Typical Heat Settings The figures given in the following tables are for guidance only Exactly which heat setting needs to be used depends on the quality of the pans and the type and quantity of the food Table Cooking and Frying When cooking without the automatic warm up function the warm up time can
22. remaining cooking time appears in the timer display field Touch the H and buttons simultaneously cooking zone and timer switch off Switching off the timer leaving the cooking zone active Select the desired cooking zone using the cooking zone buttons only the timer switches off the cooking zone is left on 19 Operation of the Cooking Surface 20 i 1 Touch the Triple Ring Zone Casserole Zone button leave your finger Automatic pan and triple ring sensing Pan and triple ring sensing is automatically activated when the cooking zone Is switched on Electronic sensors are fitted under the cooking zones These detect the material that the pan is made of the size of the base of the pan If you select a cooking zone on which there is not a pan or the pan is unsuitable F appears in the respective Heat Setting Residual Heat display If there is a suitable pan on the selected cooking zone the second third rings on the triple ring zone or casserole zone switch on automat ically if required depending on the size of the pan Suitable pans for pan and triple ring sensing All metallic pans with flat bases All pans with a base diameter that is no more than 2 cm smaller than the cooking zone marked Pay particular attention to the diam eter of the base when buying pans most manufacturers give the diameter of the rim Pans not suitable for pan and triple ring sensing glass clay and ce
23. robust however it is not unbreakable Hard and sharp objects in particular can damage the cooking surface if they fall on it e Do not use cast iron pans or pans with damaged bases that are rough or burred Scratching may occur when the pans are slid e Do not place any pans on the hob frame Scratching may occur or the paint damaged e Ensure that liquids containing acids e g vinegar lemon or scale remover do not come into contact with the hob frame otherwise matt spots will appear e f sugar or a dish containing sugar comes into contact with a hot cooking zone and then melts remove the soiling immediately whilst still hot using a scraper If it cools damage to the surface may occur on removal e Keep all items and materials that can melt away from the ceramic glass surface e g plastics aluminium foil or oven foils If something of this nature should melt onto the ceramic glass surface it must also be removed immediately using the scraper e f you wish to use special types of pan e g a pressure cooker simmer ing pan wok etc please observe the manufacturer s instructions e Avoid boiling pans dry The bases could be irreparably damaged in the process and the glass ceramic cooking surface also damaged Disposal Disposal Disposing of packaging material All materials used can be recycled The plastics are marked as follows e gt PE lt for polyethylene e g as used for the outer wrapping and the b
24. staller Please observe this instruction otherwise the warranty will not cover any damage that may occur AN Attention Only the cable fitted to the cooking surface recess may be used for connecting up the appliance Replacement cables can only be obtained from AEG Service Force Centres Part No 374 349 000 A device is to be included in the electrical installation that makes it possible to isolate the appliance from the mains supply with a mini mum contact separation of 3 mm Suitable isolation devices include e g cut outs fuses screw type fuses are to be removed from the holder earth leakage trips and contactors 230V 240V connecting line hob electrical connection L1 T brown 230V 240V blue N d reen yellow AN Important Make the electrical connection in accordance with the wir ing diagram 38 Installing and Connecting Up 39 Hier Typschild aufkleben nur fiir Werk AEG Hausgerate GmbH Postfach 1036 D 90327 Nuremburg http www aeg hausgeraete de Copyright by AEG ANC 822 947 296 03 0899
25. t as possible Rough bases e g on cast iron pans will scratch the cooking surface when slid e Use high sided pans for dishes with a lot of liquid so that nothing boils over e Ensure that the pan is in the centre of the cooking zone and covers the heated marked area Important Avoid letting enamel saucepans and frying pans boil dry he base could be damaged and then scratch the cooking surface when slid Saucepans and frying pans with sharp edges and burrs will also scratch Energy Saving Tips You will save valuable energy if you observe the following tips e Whenever possible use the automatic warm up function on your cooking zones see Cooking and Frying Table e Observe the special tips on saucepans and frying pans The pan base and cooking zone should be the same size e Dirty cooking zones and pan bases damage the glass ceramic cooking surface and increase electricity consumption e Switch the cooking zone off before cooking is finished to use the residual heat e Cooking times are reduced by up to 50 when a pressure cooker is used Not only do you save energy but more vitamins and minerals are retained Tables and Tips You will waste energy if the Pan is too small Pan lid is not Pan base is Pan is too large fitted properly uneven glass ceramic Tips for cooking with and without the automatic warm up function The automatic warm up function is suitable for e dishes that start off cold a
26. that is still warm the automatic warm up function uses the residual heat This saves time and energy Switching off a cooking zone Select the desired cooking zone using the cooking zone buttons Cooking without the automatic warm up function If you want to use the cooking zone without the automatic warm up function then select the desired heat setting with the button Select a high setting for warming up As soon as steam starts to form or the oil is hot turn back to the heat setting necessary for further cook Ing Switch on the appliance and select the desired cooking zone using the cooking zone selection buttons The decimal point in the associated display field illuminates Press the button to set the required cooking setting 1 to 4 The Heat Setting Residual Heat display field for the corresponding cooking zone indicates the current setting You can adjust the heat setting at any time using the HH and but tons as long as the cooking zone is selected Switching off a cooking zone Select the desired cooking zone using the cooking zone buttons Press the H and buttons simultaneously to switch off If you want to switch on again a cooking zone on which there is food that is already hot you should always choose the required heat setting using the button In this way you will avoid the food being over cooked by the automatic warm up function c 1 To unlock touch the lo
27. tic warm up function activated The heat setting or the cooking time is decreased using the but ton Lock button and indicator To lock the control panel against inadvertent changes to the setting touch the button for approx two seconds The lock is lifted by touching the button again for two seconds The lock can also be used as a child safety measure The indicator illuminates when the control panel is locked Triple Ring Zone Casserole Zone button indicators For switching on and off the outer or middle cooking zone of the triple ring cooking zone and the casserole zone To switch on the relevant cooking zone must be selected using the cooking zone buttons The indicators illuminate if the outer or middle cooking zone of the tri ple ring zone or the casserole zone is switched on Timer button and display field For activating the timer function for the selected cooking zone he display field shows the cooking time set or remaining for the selected cooking zone The timer can also be used as an Egg Timer Set the required cooking time The timer counts the remaining time down back to zero This function is not assigned to any cooking zone and programming is not possible in this mode of operation Timer Active indicators the four Timer Active indicators show the cooking zones for which the timer is active Each of the four cooking zones has its own indicator It is not possible to use the timer fu
28. tton COOKING zone selection 2 Hear Heat Setting Residual Heat display Heat setting selection and Lock button and indicator usauebe uam I E CEX UPPER PEE Triple Ring Zone Casserole Zone button indicators Timer button and display field Automatic pan SENSING sanken Automatic triple ring sensing Cooking zone safety switch Resetting THE sate by switch Ru Sn MS rede rec Before Using for the First Time Seir EMC TSE TING Zara seen een Operation of the Cooking Surface TOUCH CONTROL sensor buttons Switching on the appliance Switching off the applanCe suisse nee Cooking with the automatic warm up function Cooking without the automatic warm up function Locking unlocking the control panel TMC FUNEUON gt SR ER ack ee eter A RAR beste Speech dw el he ge dee Ending the timer function early Automatic pan and triple ring sensing Tables and Tips ES 500550555256 anne teen eas dris EE Eat Dacia Det Did ti il d arid uta adeat ENEI SAVING TIPS ni puts anton saan Sera
29. unds as confirmation Press the button a peep tone sounds as confirmation Your cooking surface is now ready for use again the display suddenly changes to or 4 for residual heat Check whether the On Off button has been operated accidentally the touch switches are partially covered by a damp cloth liquid or similar there has been a power cut the safety switch has been activated after switching off the cooking zones neither nor 4 for residual heat appears in the display Check whether the cooking zone was only used for a short period and is therefore not hot enough If the cooking zone is hot call AEG customer service a cooking zone cannot be switched off Check whether the touch switches are partially covered by a damp cloth or liquid the lock is activated a cooking zone cannot be switched on Check whether the lock is activated 29 30 is shown in the display Check whether a pan that is too small is on the cooking zone the cooking zone has been overheated If a cooking zone button is pressed and the pan on the cooking zone is too small F Fault appears in the display This symbol is also displayed in the case of overheating faults in the electronics or for safety rea sons Important If you call an engineer to resolve a problem listed in these notes or to rectify an error caused by incorrect use or installation a charge will be
Download Pdf Manuals
Related Search