Electrolux 54850 S Dishwasher User Manual
Contents
1. Any electrical and or plumbing work required to install this appliance should be carried out by a qualified electrician and or plumber or competent person Remove all packaging before positioning the machine If possible position the machine next to a water tap and a drain Fitting under a counter kitchen worktop or sink By removing the machine s worktop you can install it under a close fitting sink unit or a pre existing top providing the dimensions of the recess correspond to those shown in the picture Proceed as follows Remove the machine s worktop by unscrewing the two rear retaining screws pull the worktop from the back of the machine and slide out the front slots lifting the worktop Insert the machine after adjusting height and levelling with the adjustable feet When inserting the machine ensure that mo the water inlet and drain hoses are not kinked or squashed During all operations that involve accessibility to internal components the dishwasher has to be unplugged Be sure that once the appliance has been installed it is easily accessible for the Service Force Engineer If the dishwasher is later used as a free standing appliance the original worktop must be re mounted The plinth on free standing appliances is not adjustable Levelling Good levelling is essential for correct closure and sealing of the door When the appliance is correctly levelled the door will not catch on either2. telephoning 08705 929 929 Your call will be automatically routed to the Service Centre covering your post code area For the address of your local Service Force Centre and further informations about Service Force please visit the website at www serviceforce co uk Help us to help you Please determine your type of enquiry before writing or telephoning When you contact us we need to know 1 Your name address and post code 2 Your telephone number RA07 3 Clear and concise details of the fault code 4 Date of purchase 5 E NR product number F NR serial number This information can be found on the rating plate located on the right inside edge of the door Customer Care For general enquiries concerning your AEG appliance or for further in formation on AEG products you are invited to contact our Customer Care Department by letter or telephone at the address below or visit our website at www aeg co uk Customer Care Department AEG Domestic Appliances 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 350350 calls to this number may be recorded for training purposes 35 Guarantee terms 36 Guarantee conditions Standard Guarantee Conditions We AEG undertake that if within 12 months of the date of purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our option repair or replace the
3. lights of the function buttons 1 2 3 and 4 start flashing Press function button 1 the indicator lights of function buttons 2 3 and 4 turn off while the indicator light of the button 1 goes on flashing the digital display indicates the current level To change the level press button 1 Each time the button is pressed the level changes For the selection of the new level see the chart Examples if the current level is 5 by pressing button 1 once level 6 is selected if the current level is 10 by pressing button 1 once level 1 is selected To memorise the operation switch off the dishwasher by pressing the On Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode Operating instructions Filling with salt Only use salt specifically designed for use in dishwashers All other types of salt not specifically designed for use in a dishwasher especially table salt will damage the water softener Only fill with salt just before starting one of the complete washing programmes This will prevent any grains of salt or salty water which may have been spilt remaining on the bottom of the machine for any period of time which may cause corrosion To fill 1 Open the door remove the lower basket and unscrew the cap of the salt container by turning it anticlockwise 2 Pour 1 litre of water inside the container this is necessary only before filling with salt for t
4. C and 65 C 3 In the Intensiv wash programme an additional programme has been integrated which thoroughly disinfects items such as baby bottles and jam jars In order to achieve this in the final wash cycle the temperature is kept at 68 C for at least 10 minutes 4 Test programme for Test Institutes 5 This programme does not need any detergent 25 Operating instructions 26 Starting a washing programme 1 Check that the baskets have been loaded correctly and that the spray arms can rotate freely Turn on the water tap Close the dishwasher door Press the On Off button The On Off indicator light will come on setting mode Setting and starting the programme a Press the button corresponding to the required programme see Washing programmes chart The indicator light of the push button illuminates and in the digital display will appear flashing the running time of the programme that has been set in minutes After about 3 seconds from the last pressure of a button the programme starts automatically In the digital display the running time of the programme is no longer flashing b If you want to set the delay start of a washing programme Set the delay start before selecting a washing programme Press the delay start option button until the flashing number of the hours for the delay start will appear in the digital display from 1h to 19h Press the button corresponding t
5. Service Force Centre If other fault codes not described in the chart will appear please contact your Service Force Centre there are problems when operating the dishwasher 33 Operating instructions 34 the wash results are not satisfactory The dishes are not clean The wrong washing programme has been selected The dishes were arranged in such a way as to stop water reaching all parts of the surface The baskets must not be overloaded The spray arms do not rotate freely due to wrong arrangement of the load The filters in the base of the washing compartment are dirty or incorrectly positioned Too little or no detergent has been used Where there are limescale deposits on the dishes the salt container is empty or the wrong level of the water softener has been selected The drain hose connection is not correct The salt container cap is not properly closed The dishes are wet and dull Rinse aid was not used The rinse aid dispenser is empty There are streaks milky spots or a bluish coating on glasses and dishes Decrease rinse aid dosing Water drops have dried onto glasses and dishes Increase rinse aid dosing The detergent may be the cause Contact the detergent manufacturer s consumer care line Service Service In the event of your appliance requiring service or if you wish to purchase spare parts contact your local AEG Service Force Centre by
6. any object that can absorb water may not be washed in the dishwasher e Before loading the dishes you should Remove large left overs Soften remnants of burnt food in pans e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other To avoid damage to glasses they must not touch Lay small objects in the cutlery basket e Plastic items and pans with teflon have a tendency to retain water drops these items will not dry as well as porcelain and steel items Operating instructions Open the door and slide out the baskets to load the dishes The lower basket The lower basket is designed to take saucepans lids plates salad bowls cutlery etc Serving dishes and large lids should be arranged around the edge of f tC M i a K ey Mt hverni the basket ensuring that the spray arms can turn freely fiT ti IN PON i eal The two rows of prongs on the lower basket can be easily lowered to allow you to load pots pans and bowls Operating
7. dangerous to alter the specifications or attempt to modify this product in any way Any electrical and plumbing work required to install this appliance should be carried out by a qualified and competent person Care must be taken to ensure that the appliance does not stand on the electrical supply cable The sides of the dishwasher must never be drilled to prevent damage to hydraulic components Child safety This appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Packaging parts may be dangerous for children who could even be suffocated You should therefore keep all packaging well away from children Operating instructions The water in your dishwasher is not for drinking Detergent residues may still be present in your machine Keep children well away from your dishwasher when the door is open Keep all detergents in a safe place out of children s reach Your dishwasher in day to day use Items that are contaminated by petrol paint steel or iron debris corrosive acidic or alkaline chemicals must not be washed in this dishwasher Under no circumstances should you open the door whilst the appliance is in operation especially during the washing phase hot water may escape However if the door is opened a safety device ensures that the machine stops Only use products detergent salt and rinse aid specifically des
8. each respective supply container is automatically deactivated and also the indicator lights for salt and rinse aid are deactivated Once selected this option button indicator light illuminated it will remain active also for the following washing programmes to deactivate the function press the button button indicator light off Once the programme is running the 3 in 1 function can no longer be changed If you want to exclude the 3 in 1 function you have to cancel the programme setting see chapter Starting a washing programme To cancel a washing programme in progress and then deactivate the 3 in 1 function In this case you have to set a washing programme again With the use of 3 in 1 combi detergent tablets the cycle durations given in the Washing programmes chart may change Operating instructions Deactivation activation of the 3 in 1 function The dishwasher must be switched off 1 Press the On Off button The On Off indicator light illuminates setting mode If other indicator lights are on this means that a wash programme has been selected The programme must be cancelled press simultaneously the function buttons 2 and 3 for about 2 seconds All the indicator lights will turn off except for the On Off indicator light and eventually salt and rinse aid indicator lights indicating that the set programme has been cancelled and the machine is now in setting mode 2 Press simultaneously function bu
9. Ensure that the lid is closed after every refill Clean up any rinse aid spilt during filling with an absorbent cloth to avoid excess foaming during the next wash Only use branded rinse aid for dishwashers Never fill the rinse aid dispenser with any other substances e g dishwasher cleaning agent liquid detergent This would damage the appliance Operating instructions i Adjusting the dose According to the finish and drying results obtained adjust the dose of rinse aid by means of the 6 position selector position 1 minimum dosage position 6 maximum dosage The dose is factory set in position 4 Increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or knife blades Top up the rinse aid when the indicator light on the control panel illuminates Operating instructions i If you are using dishwasher detergent that already contains rinse aid it is necessary to deactivate rinse aid dispenser in order to avoid a double dosage Deactivation activation of the rinse aid dispenser The dishwasher must be switched off When the rinse aid dispenser has been deactivated the rinse aid indicator light on the control panel is automatically deactivated 1 Press the On Off button The On Off indicator light illuminates setting mode If other indicator lights are on thi
10. FAVORIT 54850 S Dishwasher Instruction book PERFEKT IN FORM UND FUNKTION AEG A i Qg il Dear customer Please read this User Information carefully and keep it to refer to at a later date Pass it on to any subsequent owner of the appliance The following symbols are used in the text Safety instructions Warning Notes that concern your personal safety Attention Notes that show how to avoid damage to the appliance Useful tips and hints Environmental information Your dishwasher has the new washing system IMPULSE WASHING With this dishwashing system the motor speed and spray pressure are varied during the wash cycle to achieve better cleaning of the dishes It is for this reason that the noise level varies during the dishwashing cycle Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Contents CONTENTS Operating instructions Safety instructions Disposal Economical and ecological dishwashing Description of the appliance The control panel Prior to using for the first time Setting the water softener Filling with salt Rinse aid In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Use of detergent Different kinds of detergent Washing programmes Starting a washing programme Maintenanc
11. The drain hose can face either to the right or left of the dishwasher Ensure the hose is not bent or squashed as this could prevent or slow down the discharge of water The sink plug must not be in place when the machine is draining as this could cause the water to syphon back into the machine If you use a drain hose extension it must be no longer than 2 metres and its internal diameter must be no smaller than the diameter of the hose provided 1 1 4 lt max 100 cm min 30 cm npg Likewise the internal diameter of the couplings used for connections to the waste outlet must be no smaller than the diameter of the hose provided Attention Our appliances are supplied with a security device to protect against the return of dirty water back into the machine If the spigot of your sink has a no return valve incorporated this can prevent the correct draining of your dishwasher We advise you therefore to remove it Installation instructions Electrical connection If the plug that is fitted to your appliance is not suitable for the sock et it must be cut off and the appropriate plug fitted Important The wires on the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live If you fit your own plug the colours of the wires in the mains lead of your appliance may not correspond with the markings identif
12. an also be set with the help of these buttons the setting of the water softener deactivation activation of the rinse aid dispenser deactivation activation of the 3 in 1 function the cancelling of a programme in progress Programme selection buttons the selection of a washing programme occurs by pressing one of these push buttons see Washing programmes chart Delay start option button this option allows the start of the programme to be delayed from 1 to 19 hours Indicator lights have the following meanings g Salt refilling indicator light illuminates when the salt has run out ye Rinse aid refilling indicator light illuminates when the rinse aid has run out The salt and rinse aid indicator lights are never illuminated while a washing programme is running even if filling with salt and rinse aid is necessary Operating instructions The digital display indicates the level of hardness to which the water softener is set if the rinse aid inflow is activated deactivated the approximative remaining time of the running programme the countdown of the delay start fault codes concerning malfunction of the dishwasher 3 in 1 function this appliance is equipped with the option 3 in 1 that allows the use of the 3 in 1 combi detergent tablets This function can be selected with all washing programmes With the selection of this function the inflow of rinse aid and salt from
13. can be a hazard Operating instructions 22 Use of detergent Only use detergents specifically designed for use in dishwashers Using no more then the correct amount of detergent contributes to reducing pollution Prior to the start of a wash programme The detergent is released during the washing phase Please observe the manufacturer s dosing and storage recommendations as stated on the detergent packaging Fill with detergent 1 If the lid is closed press release button 1 The lid springs open 2 Fill the detergent dispenser 2 with detergent The marking indicates the dosing levels 20 approximately 20 g of detergent 30 approximately 30 g of detergent DE19 3 All programmes with prewash need an additional detergent dose 5 10 g that must be placed in the prewash detergent chamber 3 This detergent will take effect during the prewash phase 4 Close the lid and press until it locks in place Operating instructions Different kinds of detergent Detergent tablets Detergent tablets of different brands dissolve at different speeds For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programmes Therefore please use long programmes when using detergent tablets to ensure the complete removal of detergent residuals Do not place the tablets in the tub or in the cutlery basket as this will result in
14. d salts the harder your water Is Water hardness is measured in equivalent scales German degrees French degrees and mmol l millimol per litre The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area The water softener must be set in both ways manually using the water hardness switch and electronically using the function buttons on the control panel Operating instructions a Setting manually 1 2 4 The dishwasher is factory set at position Turn the water hardness dial to Open the dishwasher door Remove the lower basket from the dishwasher position 1 or 2 see table Replace the lower basket b Setting electronically The dishwasher must be switched off The dishwasher is factory set at level 5 Press the On Off button The On Off indicator light illuminates setting mode If other indicator lights are on this means that a wash programme has been selected The programme must be cancelled press simultaneously the function buttons 2 and 3 for about 2 seconds All the indicator lights will turn off except for the On Off indicator light and eventually salt and rinse aid indicator lights indicating that the set programme has been cancelled and the machine is now in setting mode Press simultaneously function buttons 2 and 3 until the indicator
15. e and cleaning Cleaning the filters What to do when Service Guarantee terms Technical specifications Installation instructions Fitting under a counter Levelling Water supply connections Water inlet hose with safety valve Water outlet hose connection Electrical connection Hints for test centres NOD fF A 11 13 14 17 17 18 19 20 21 22 23 25 26 29 29 32 35 36 38 39 39 39 40 41 42 43 44 Operating instructions OPERATING INSTRUCTIONS A Safety instructions i The safety of AEG electrical appliances conforms to accepted rules of technology and the Appliance Safety Act We as manufacturers however see ourselves as being obliged to familiarise you with the following safety instructions It is most important that this instruction book should be retained with the appliance for future reference Should the appliance be sold or transferred to another owner or should you move house and leave the appliance always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information This information has been provided in the interest of your safety You MUST read it carefully before installing or using the appliance Installation Check your dishwasher for any transport damage Never connect a damaged machine If your dishwasher is damaged you should contact your supplier For safety reasons it is
16. he first time 3 Using the funnel provided pour in the salt until the container is full 4 Replace the cap making sure that there is no trace of salt on the screw thread or on the gasket 5 Screw on the cap tightly turning it clockwise until it stops with a click SR14 The salt container will require topping up periodically You are reminded of this by the salt indicator light on the control panel which comes on when the salt has finished The salt indicator light on the control panel can remain illuminated for 2 6 hours after the salt has been replenished assuming the dishwasher remains switched on If you are using salts that take longer to dissolve then this can take longer The function of the machine is not affected Do not worry if water over flows from the unit when filling with salt this is quite normal Operating instructions Rinse aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing and spot and streak free drying The dispenser which is positioned inside the door holds about 110 ml of rinse aid which is sufficient for 16 40 dishwashing programmes depending upon the dosage setting Filling with rinse aid 1 Open the container by pressing the release button A 2 Add the rinse aid until the container is completely full The maximum level for filling is indicated by max II DE a C er Sle Eiai BRO
17. id container have been filled with salt and rinse aid respectively and using the test programme see Washing programmes chart Load 9 standard place settings Rinse aid setting Position 4 type III Detergent dosage 5 g 20 g type B Arrangement upper Arrangement upper basket without smaller basket with smaller bow lower basket bowl and salad bowl and salad bowl Arrangement cutlery basket Cup racks position A 45 A From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx 14 billion USD in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de Copyright by AEG 152 963 20 0 Subject to change without notice
18. igned for use in dishwashers Long bladed knives stored in an upright position are a potential hazard e Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket When finishing loading or unloading close the door as an open door can be a hazard Do not sit or stand on the open door Isolate the appliance from the power supply and turn off the water supply after use This product should be serviced by an authorised service engineer and only genuine spare parts should be used Under no circumstances should you attempt to repair the machine yourself Repairs carried out by inexperienced persons may cause injury or serious malfunctioning Contact your local Service Force Centre Always insist on genuine spare parts Operating instructions F Disposal Dispose of the dishwasher packaging material correctly All packaging materials can be recycled Plastic parts are marked with standard international abbreviations gt PE lt for polyethylene e g sheet wrapping material gt PS lt for polystyrene e g padding material always CFC free gt POM lt for polyoxymethylene e g plastic clips Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling As and when you cease to use your dishwasher and withdraw it from service your should render it unserviceable before having it disposed of A N Warni
19. instructions The cutlery basket Place knives forks and spoons in the cutlery basket with their handles pointing downwards Arrange cutlery loosely and distribute it in all compartments so that each individual article has good contact with washing water Also do not arrange spoons and forks with their dirty side in contact with each other Important Exceptionally long cutlery such as soup ladles kitchen knives or the like may obstruct the upper spray arm Such cutlery can be placed in the upper basket To unload your dishwasher more easily you can take the cutlery basket out of the lower basket and unfold it This makes it easier to remove small pieces of cutlery Important note To prevent the full cutlery basket from inadvertently unfolding when being taken out place your hand right round the two piece handle and hold it firmly 1 Place the cutlery basket on a firm support table worktop and unfold both handle parts 2 After unfolding fold back both handle parts Ul25 Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket Take care when loading or unloading sharp items such as knives Operating instructions 20 The upper basket The upper basket is designed for plates dessert plates saucers dinner plates of u
20. ith you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domestically i e a normal household e The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliance France Senlis 33 0 344 62 29 29 Germany Nurnberg 49 0 800 234 7378 Italy Pordenone 39 0 800 117511 Sweden Stockholm 46 0 8 672 53 60 UK Slough 44 0 1753 219899 37 Operating instructions Technical specifications This appliance complies with the following E E C Directives C 73 23 or 19 2 73 Low Voltage Directive and subsequent modifications 89 336 or 3 5 89 Electromagnetic Compatibility Directive and subsequent modifications 38 Installation instructions Installation instructions A
21. multaneously function buttons 2 and 3 until all the indicator lights turn off except for the On Off indicator light and eventually the rinse aid and salt indicator lights indicating that the running programme has been cancelled If a new washing programme will be selected check that there is detergent in the detergent dispenser 27 Operating instructions 28 7 Cancelling the delay start in progress To cancel a delay start in progress you have to reset the dishwasher follow the same instructions given in To cancel a washing programme in progress Cancelling a delay start involves also the cancelling of the setted washing programme In this case you have to set the washing programme again 8 End of the washing programme The dishwasher will automatically stop In the digital display appears O remaining programme time only in this case the programme has ended The indicator light of the programme just ended will remain on If the door is not immediately opened at the end of the programme air will circulate inside the dishwasher to prevent residual steam recondensing on the dishes as water droplets This device operates intermittently for about 20 minutes as long as the dishwasher is switched on If the On Off button is pressed or the door is opened during these 20 minutes the device will be automatically cancelled Switch off the dishwasher by pressing the On Off button the On Off indicator light tu
22. ng Children at play could lock themselves in your dishwasher or otherwise endanger their lives Therefore cut off the power supply cable and make the door closing device unusable to prevent children from being trapped inside To dispose of the appliance please take it to a recycling centre or to your dealer who may for a small contribution to the costs dispose of it for you Economical and ecological dishwashing Ensure that the water softener is correctly adjusted Do not pre wash under running water Select the wash programme to suit the nature and degree of the soiling on the dishes Do not use more detergent dishwasher salt and rinse aid than is recommended in these operating instructions and by the manufacturer of the respective product Operating instructions Description of the appliance on pS PON Upper basket stop Water hardness dial Salt container Detergent dispenser Control panel Rating plate 9 10 11 12 Rinse aid dispenser Filters Lower spray arm Upper spray arm Upper basket Worktop Operating instructions The control panel Function 3 in 1 On Off buttons indicator light Digital indicator light D On Off Programme selection Indicator button buttons lights Delay start option button Function buttons in addition to the dishwashing programme selected the following functions c
23. o the required programme see Washing programmes chart After about 3 seconds the countdown starts automatically The countdown will decrease with steps of 1 hour Opening the door will not modify or interrupt the countdown Once the delay start has elapsed the programme will start automatically Operating instructions a Note it is possible to select a washing programme and the delay start also with the door slightly opened In this case the start of the programme or of the countdown will occur after the closure of the door a Press On Off button b Select a washing programme and if required the delay start c Close the door The programme or the countdown will start automatically after about 3 seconds from the closure of the door To interrupt or cancel a washing programme in progress Interrupt or cancel a washing programme in progress ONLY if it s absolutely necessary Attention Hot steam may escape when the door is opened Open the door carefully To interrupt a washing programme in progress a Open the dishwasher door the programme will stop Close the door the programme will start from the point in which it was interrupted b Press the On Off button in this case all the indicator light turn off Press the On Off button again the programme will start from the point at which it was interrupted To cancel a washing programme in progress To cancel a washing programme in progress press si
24. oducts should be strictly used according to the detergent manufacturers instructions 3 If you encounter problems when using 3 in 1 products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special advice When using combination 3 in 1 products select the 3 in 1 function If you decide to turn back to the use of the standard detergent system we advise that you Refill both the salt container and rinse aid dispenser Switch the water hardness setting to the highest possible position and run from 1 to 3 normal washing programmes without a load Readjust the water hardness setting again according to the hardness of the water in your area For best results we recommend the use of Finish detergents rinse aid and salt DE15 Raig DISHWASHER SALT Operating instructions Washing programmes 1 The consumption values were obtained under standardised conditions They depend on how full the baskets for the dishes are Variations are therefore possible in practice 2 When using this programme the degree of water clouding determines the amount of soiling on the dishes The length of the programme and water and energy consumption can vary greatly depending upon the load and how dirty the dishes are Depending upon the soiling the temperature of the water will be automatically adjusted to between 50
25. p to 24 cm in diameter salad bowls cups and glasses Arrange items on and underneath the cup racks so that water can reach all surfaces Glasses with long stems can be placed upside down in the cup racks For taller items the cup racks can be folded upwards Light items plastic bowls etc must be loaded in the upper basket and arranged so they do not move A N Before closing the door ensure that the spray arms can rotate freely Operating instructions Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position Maximum height of the dishes in upper basket lower basket With upper basket raised 20 cm 31 cm With upper basket lowered 24 cm 27 cm To move to the higher position proceed as follows 1 Pull out the basket until it stops 2 Carefully lift both sides upwards until the mechanism is engaged and the basket is stable Attention Never lift or lower the basket on one side only When the basket is in the heigher po sition you will not be able to use the cup rack s The lower basket to the original position proceed as follows 1 Pull out the basket until it stops 2 Carefully lift both sides upwards ane then allow the mechanism to drop back down slowly keeping hold of it After loading your machine always close the door as an open door
26. poorer wash results The tablets should be placed in the detergent dispenser Concentrated detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caustic components low alkaline concentrated detergents with natural enzymes The use of 50 C washing programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are specially matched to the dirt dissolving properties of the enzymes in the concentrated detergent For this reason 50 C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C programmes Combi detergents If you are using dishwasher detergent that includes the rinse aid function this must be placed in the detergent compartment In this case it is necessary to deactivate the rinse aid dispenser in order to avoid a double dosage see Deactivation activation of the rinse aid dispenser 23 Operating instructions 24 Use of 3 in 1 combi detergents General advice These products are detergents with integrated and combined detergent rinse aid and salt functions 1 Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manufacturers on the product packaging 2 These pr
27. rns off Open the door and wait a few minutes before removing the dishes in this way they will be cooler and the drying will be improved 9 Unloading the dishwasher AN Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down before removing from the appliance Empty the lower basket first and then the upper one this will avoid water dripping from the upper basket onto the dishes in the lower one Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler then the dishes When the washing programme has finished it is recommended that the dishwasher is unplugged and the water tap turned off Operating instructions Maintenance and cleaning AN Clean the external surfaces of the machine and control panel with a damp soft cloth If necessary use only neutral detergents Never use abrasive products scouring pads or solvent acetone trichloroethylene etc Ensure that the seals around the door the detergent and rinse aid dispensers are cleaned regularly with a damp cloth We recommend every 3 months to run a 65 C wash programme without dishes using detergent Cleaning the filters The filters must be checked and cleaned from time to time Dirty filters will degrade the washing result 1 Open the door remove the lower basket 2 The dishwasher filter system comprises a coarse A B a microfilter C and a flat filter D Some di
28. s means that a wash programme has been selected The programme must be cancelled press simultaneously function buttons 2 and 3 for about 2 seconds All the indicator lights will turn off except for the On Off indicator light and eventually salt and rinse aid indicator lights indicating that the set programme has been cancelled and the machine is now in setting mode 2 Press simultaneously function buttons 2 and 3 until the indicator lights of the function push buttons 1 2 3 and 4 start flashing 3 Press function button 2 the indicator lights of function buttons 1 3 and 4 turn off while the indicator light of the function button 2 goes on flashing the digital display indicates the current setting Gd _ rinse aid dispenser deactivated g inse aid dispenser activated factory setting 4 To change the setting press function button 2 again the digital display indicates the new setting 5 To memorise the operation switch off the dishwasher by pressing the On Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode Operating instructions In daily use AS e Check if it s necessary to refill with dishwasher salt or rinse aid e Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Loading cutlery and dishes Sponges household cloths and
29. same FREE OF CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre Any appliance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights e Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are subject to rental agreements e Products of AEG manufacture which are not marketed by AEG Guarantee terms European Guarantee If you should move to another country within Europe then your guarantee moves w
30. shwasher will only have a coarse filter A a microfilter C and a flat filter D Unlock the filter system using the handle on the microfilter and remove MA32 3 Turn the handle about s a turn anticlockwise and remove MA39 29 Operating instructions 30 AN 4 Take hold of the coarse fine filter A B by the handle with the hole and remove from the microfilter C 5 Clean all filters thoroughly under running water 6 Remove the flat filter D from the base of the washing compartment and clean both faces thoroughly MA38 7 Put the flat filter D back in the base of the washing compartment 8 Place the coarse fine filter A B in the microfilter C and press together 9 Put the filter combination in place and lock by turning the handle clockwise to the stop During this process ensure that the flat filter does not protrude above the base of the washing compartment Under no circumstances may the dishwasher be used without filters Incorrect repositioning and fitting of the filters will produce poor washing results NEVER try to remove the upper spray arm If residues of soil have clogged the holes in the upper spray arm remove them with a toothpick Operating instructions Prolonged periods of non operation If you are not using the machine for any period of time you are advised to 1 Unplug
31. side of the cabinet If the door does not close correctly loosen or tighten the adjustable feet until the machine is perfectly level 39 Installation instructions 40 Water supply connections For making the connection itself the coupling nut fitted to the machine s supply hose is designed to screw onto either a 3 4 inch gas thread spout The water pressure must be within the limits given in the Technical specifications Your local Water Authority will advise you on the average mains pressure in your area The water inlet hose must not be kinked crushed or entangled when it is being connected up The dishwasher features fill and drain hoses which can be turned either to the left or the right to suit the installation by means of the locknut The locknut must be correctly fitted to avoid water leaks Attention NOT all models of dishwashers have fill and drain hoses provided with locknut In this case this kind of facility is not possible If the machine is connected to new pipes or pipes which have not been used for a long time you should run the water for a few minutes before connecting the inlet hose Do not use for connection old hoses which have been used in another appliance The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations Installation instructions Water inlet hose with safety
32. the appliance and then turn off the water 2 Leave the door ajar to prevent the formation of any unpleasant smells 3 Leave the inside of the machine clean Frost precautions Avoid placing the machine in a location where the temperature is below 0 C If this is unavoidable empty the machine close the appliance door disconnect the water inlet pipe and empty it Moving the machine If you have to move the machine moving house etc 1 Unplug it 2 Turn the water tap off 3 Remove the water inlet and discharge hoses 4 Pull the machine out together with the hoses Avoid over tilting the machine during transportation 31 Operating instructions What to do when Certain problems are due to the lack of simple maintenance or oversights which can be solved with the help of the instructions given here without calling out an engineer a flashing fault code appears The intervention of an alarm is indicated by indicator light of the programme in progress is flashing a fault code visible in the digital display Open the door and carry out the following suggested corrective actions see following chart Operating instructions Once the checks have been carried out close the door and press the push button of the programme that was running before the intervention of the alarm the programme will continue from the point in which it was interrupted If the fault code reappears contact the
33. ttons 2 and 3 until the indicator lights of the function push buttons 1 2 3 and 4 start flashing 3 Press the function push button 4 the indicator lights of function push buttons 1 2 and 3 turn off while the indicator light of the function push button 4 goes on flashing 4 Press the function button 4 again the 3 in 1 indicator light illuminates indicating that the 3 in 1 funcion is active To deactivate the function press the function button 4 again the indicator light turns off 3 in1 function active indicator light on 3 in 1 function not active indicator light off 5 To memorise the operation switch off the dishwasher by pressing the On Off button or wait about 60 seconds after which the dishwasher will automatically return to setting mode Operating instructions Prior to using for the first time Before using your dishwasher for the first time 1 Ensure that the electrical and water connections comply with the installation instructions 2 Remove all packaging from inside the appliance 3 Set the water softener 4 Pour 1 litre of water inside the salt container and then fill with special dishwasher salt 5 Fill the rinse aid dispenser Setting the water softener The dishwasher is equipped with a water softener designed to remove minerals and salts from the water supply which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these minerals an
34. valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water Please take care when installing the water inlet hose The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the water inlet hose or the safety valve in water If water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by a Service Force Engineer Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve The water inlet hose must hang vertically down from the water supply tap 41 Installation instructions 42 Water outlet hose connection The end of the drain hose can be connected in the following ways 1 To the sink outlet spigot securing it to the underside of the work surface This will prevent waste water from the sink running into the machine 2 Hooked over the edge of the sink using the special curved plastic guide if provided with the machine 3 To a stand pipe provided with vent hole minimum internal diameter 4 cm The waste connection must be at a height of between 30 cm minimum and 100 cm maximum from the bottom of the dishwasher
35. ying the terminals in your plug Proceed as follows 1 Connect the Green and Yellow earth wire to the terminal in the plug which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the Blue neutral wire to the terminal in the plug which is marked with the letter N or coloured black 3 Connect the Brown live wire to the terminal in the plug which is marked with the letter L or coloured red The plug moulded onto the lead incorporates a 13amp GREEN amp YELLOW BSI362 fuse Only ASTA or BSI fuses should be used The plug must not be used if the fuse cover carrier is lost The cover carrier is indicated N by the coloured insert at the base of the product A replacement cover carrier BROWN must be obtained from your local Service Force Centre 13A4 BLUE CORD CLAMP This appliance must be earthed The manufacturer declines any responsibility should this safety measure not be observed Warning A cut off plug inserted into a 13amp socket is a serious safety shock hazard Ensure that the cut off plug is disposed of safely 43 Hints for test centres 44 Hints for test centres Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme see Washing programmes chart Testing in accordance with EN 60242 must be carried out when the salt dispenser and rinse a
Download Pdf Manuals
Related Search