Edelbrock 641540 Automobile Parts User Manual
Contents
1. HUSSELL RUSSELL FORD 5 0L COMPLETE EFI PLUMBING KIT Catalog 641540 INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new complete fuel system kit If you have any questions please call our Technical Hotline at 1 800 416 8628 7 00 am to 5 00 pm Monday Friday Pacific Standard Time or e mail us at Edelbrock Edelbrock com KIT CONTENTS RN Edelbrock Fuel Pump 1790 01 U 1 Edelbrock Fuel Pressure Regulator Kit 1728 U 20 ft U 1 Edelbrock Electric Fuel Pump Relay Kit 1795 U 20 ft U 2 Russell 3 8 NPT x 6 AN male adapter 0 10 U 2 Russell 3 8 NPT x 8 AN male adapter 0 10 U 1 Mustang 5 0 Fuel Rail Kit O3 O2 8 AN black dry sump union a4 a3 6 AN black dry sump union O 1 O12 Tie wraps O2 01 10 Micron fuel filter 10 AN 1 0 O2 01 Billet Y block 10 AN inlet 8 AN outlets O4 U 5 10 AN straight x 8 flare reducer U 10 ft U01 0 100 psi fuel pressure gauge U 10 ft Russell assembly lube sealant Russell 8 hose Russell 6 hose Russell 6 cushion clamps Russell 8 cushion clamps 6 AN Straight hose end 8 AN Straight hose end 6 AN 45 Swivel hose end 8 AN 45 Swivel hose end 6 90 Swivel hose end 8 90 Swivel hose end Russell 3 16 Wrap It wire protective sleeve Russell 5 16 Wrap It wire protective sleeve TOOLS amp SUPPLIES RECOMMENDED U AN Wrenches O EFI Fuel line disconnect tool U Multimeter or test light U Wire strippers U Wire terminals2. amp connectors U Assorted nuts amp bolts U Basic hand tools U Miscellaneous hardware for mounting components U Drill motor A bits U Wire crimpers or soldering equipment U Extra wire Red amp Black 12 gauge amp 18 gauge U 10A inline fuse Gasoline and gasoline fumes are extremely flammable Work in a well ventilated area away from open flames sparks or other sources of ignition Try to contain gasoline when connections are loosened and clean up any WARNING spills immediately Failure to do so can result in a fire or explosion IMPORTANT NOTE Proper installation is the responsibility of the installer Improper installation will void warranty and may result in poor performance and engine or vehicle damage 2007 Edelbrock Corporation Brochure No 63 641540 Page 1 of 5 Catalog 641540 Rev 10 07 AJ mc BEFORE BEGINNING Someone who has a basic knowledge of automobile repair and modification and is familiar with and comfortable with working on their vehicle can accomplish the mechanical installation of this kit using common tools and procedures However this kit is designed to allow you to custom fit the fuel lines and components to your application and will require that you cut hoses to fit and drill holes for fuel pressure regulator mounting junction blocks etc If you do not feel comfortable with any of the steps listed below please consult a qualified professional installer Make sure
3. N to 8AN adapter fitting into the bottom of the Y block Install the 8 AN dry sump adapter fittings into the two exit ports of the Y block Install the fuel pressure gauge into the 1 8 NPT port located on the front of the Y block Find a suitable location for the Y block on the vehicle It might be necessary to fabricate a custom mounting bracket to install the Y block Mount the Y block onto the vehicle Russell fuel hose assembly and install Note Follow the included hose assembly instructions to properly build the hose assemblies for the fuel system Ensure that the fuel hoses are properly located and installed so as to prevent damage during normal operation of the vehicle Please note that the instructions below give an example of how this fuel system can be routed It is highly recommended that the installer pre plan the routing of the fuel system kit to determine which hose end fittings should be used for each hose assembly Use the supplied hose cushion clamps to support the fuel hose as needed 2007 Edelbrock Corporation Brochure No 63 641540 Determine the hose path and length required for the fuel hose leading from the fuel tank outlet fitting not included to the fuel inlet fitting of the fuel pump Build and install the hose assembly Determine the hose path and length required for the fuel hose from the fuel pump to the fuel filter inlet Build and install the hose assembly Determine the hose paths and
4. cluded fuel pressure regulator instructions for details Following the instructions provided with the fuel pressure regulator mark and drill the mounting holes for the fuel pressure regulator bracket Install 3 dry sump fittings 6 AN into the inlet and exit ports of the regulator Install the vacuum hose from the regulator to the intake manifold It might be possible to use your stock vacuum hose for the regulator depending on the placement of the fuel pressure regulator Roughly install the fuel pressure regulator onto the vehicle to facilitate hose assembly installation Edelbrock fuel pump install 1 Install two 2 10 AN to 8AN fittings into the fuel pump Find a suitable location for the fuel pump on the vehicle It is highly recommended that the fuel pump is located below the sump of the fuel tank to prevent any fuel from draining back into the tank Following the instructions included with the fuel pump install the fuel pump to the vehicle Russell Relay kit install 1 2 1 Find a safe and clean location in the engine compartment for the placement of the fuel regulator and its mounting bracket supplied In most applications the best placement for the regulator is on the firewall Make sure that the location will allow access for three hoses entering from the sides and Note exiting from the bottom of the regulator 2007 Edelbrock Corporation Brochure No 63 641540 Page 3 of 5 Mount Edelbrock f
5. lengths required for the fuel hose leading from the fuel filter outlet to the inlet of the Y block Build and install the hose assembly Determine the hose path and lengths required for the fuel hose leading from the outlets of the Y block to the inlets of each of the fuel rails Build and install the two hose assemblies Determine the hose path and lengths required for the fuel hoses leading from outlets of the fuel rails to the inlets of the fuel pressure regulator Build and install the two hose assemblies Determine the hose path and lengths required for the fuel hose leading from the fuel pressure regulator outlet to the fuel tank inlet fitting not included Properly install the fuel pressure regulator to the chassis at this time Final assembly checklist 1 Page 4 of 5 Make sure all connections are tight Make sure the fuel supply and return hoses were not kinked or pinched during installation Check for any interferences around the fuel system hoses and fittings The use of tie wraps to secure the hoses is recommended Reconnect the negative battery terminal Turn the ignition or fuel pump power switch to the on position but do not start vehicle Check for leaks With the ignition still in the on position adjust the fuel pressure to the desired level Refer to the instructions provided with the fuel pressure regulator for proper adjustment procedures Continue to check for leaks Refer to the instruc
6. necessary components onto the fuel rail before installing in vehicle for ease of assembly Be sure to use thread sealing compound on NPT threads to prevent leaks Please note that the instructions below give an example of how this fuel system can be routed It is highly recommended that the installer pre plan the routing of the fuel system kit to determine which fittings should be used for inlets and outlets on the fuel rails as well as the other components included in this kit Using the supplied 3 8 NPT plug install into the front end of the driver s side fuel rail This end of the fuel rail will be located behind the distributor Install the 3 8 NPT male to 8 AN male fittings into the inlets of the fuel rails Install the 3 8 NPT male to 6 AN male fittings into the outlets of the fuel rails Depending on which intake manifold is used in conjunction with this fuel system kit the fuel rail spacers included might need to be used to properly space the drivers side fuel rail from the intake manifold Mount the assembled fuel rails onto the intake manifold Careful attention should be paid to prevent any damage to the injector o rings during installation Fasten the fuel rails to the intake manifold using the supplied hardware or the factory hardware Fuel pressure regulator install Note Some modification to the fuel pressure regulator bracket may be needed for the correct fitment in your desired location Refer to the in
7. tions provided with the fuel pressure regulator for additional adjustments after starting the vehicle Catalog 641540 Rev 10 07 AJ mc BuIy 0 SIE 0L 0 ALN 8 JBINPSY SIEW O L 0 ALN 8 DU 9S0H 8 DU 9S0H 8 EE 0641 N d dW 1d 4 EEE J 9S0H 8 ANYL 144 Du 0 SIE 0L 0 ILN 8 SCH KEE 722 EE puq 8SOH 8 afneJ nssald jan4 pug 9S0H 8 LAN 8 0 ILN 8 REGULATOR PZN 1728 uoun duns Aug 8 JON 8 0 ILN 8 pug S0H 8 Catalog 641540 Rev 10 07 AJ mc Page 5 of 5 2007 Edelbrock Corporation Brochure No 63 641540 FIUSSELL Edelbrock Corporation 2700 California St Torrance CA 90503 Tech Line 800 416 8628 E Mail Edelbrock Edelbrock com 2007 Edelbrock Corporation Catalog 641540 Brochure No 63 641540 Rev 10 07 AJ mc
8. to read the instructions provided with the supplied fuel rail and fuel pressure regulator These will be referenced throughout this instruction sheet WARNING MAKE SURE TO DISCONNECT YOUR BATTERY TO AVOID THE POTENTIAL FOR SPARKS IN THE WORK AREA SOME PROCEDURES IN THIS INSTALLATION WILL REQUIRE THE VEHICLE TO BE RAISED ON JACKSTANDS OR A LIFT WHEN RAISING A VEHICLE MAKE SURE THE VEHICLE IS ON LEVEL GROUND AND SUPPORTED SECURELY BY JACKSTANDS NEVER WORK UNDER A VEHICLE THAT IS SUPPORTED BY A JACK ONLY AFTER INSTALLATION BEFORE STARTING THE VEHICLE ALWAYS make sure to check for any leaks BEFORE starting the vehicle Reconnect the battery and turn the ignition key to the ON position This will activate the fuel pump and pressurize the fuel system If any leaks are present turn the ignition OFF disconnect the battery and make the necessary corrections before continuing MUSTANG 5 0 COMPLETE FUEL SYSTEM KIT Stock fuel rail disassembly 1 Make sure the vehicle is on level ground and the gear 8 Remove the fuel regulator vacuum hose fuel rail and selector is in park or 1st gear Set the parking brake or the fuel injectors chock the wheels 9 Inspect and replace the fuel injector o rings if 2 Make sure that the vehicle has cooled down necessary 3 Disconnect the negative terminal on the battery 10 You will also need to remove the remaining fuel hard tube feed and return running from the fuel rail to the 4 Thoro
9. uel pump relay at a suitable location under the hood e g radiator support inner fender firewall away from extreme heat Run one large 12 gauge red relay wire back to red lead wire on the fuel pump Wire can be routed underneath along with other wires hardlines etc or through the interior of the vehicle A 10 amp inline fuse not supplied is recommended on this relay circuit Route wires so that any possible cutting chafing snagging pinching or burning from suspension driveline or exhaust components will be avoided Cover wires with supplied Russell Wrap it protective sleeve and use supplied cable ties to secure wires Catalog 641540 Rev 10 07 AJ mc Connect other large 12 gauge red relay wire to the positive battery terminal Connect small pink relay wire to a 12V switched key on power supply e g terminal in a fuse box or splice on ignition switch Connect black relay wire and black fuel pump lead wire to a good chassis engine or battery ground Russell Profilter install 1 Install two 2 10 AN to 8 AN fittings into the Profilter Note the inlet and outlets of the fuel filter during the installation Find a suitable location for the Profilter on the vehicle The location should allow for easy access to the fuel filter to facilitate servicing in the future Install the fuel filter onto the vehicle using the supplied bracket Russell Y Block install l Install the 10 A
10. ughly clean the area surrounding the fuel lower firewall injectors and the fuel rail This will prevent debris from entering the fuel system or the intake manifold upon Fuel tank removal fuel rail injector removal Note Use caution when lowering the fuel tank as some fuel 5 Relieve residual fuel pressure in the fuel system will be remaining in the fuel tank These instructions Remove the dust cap cover over the Schrader valve have been written with the intent of the installer using located on the fuel tube leading to the rail Hold a shop a fuel tank or cell equipped with a sump towel or rag around the valve while relieving the fuel pressure to prevent any fuel spray 1 Drain the fuel from the fuel tank 6 Using the EFI coupling release tool disconnect the fuel 2 Raise vehicle using a vehicle lift or by using a jack and feed and return lines Use a shop towel or rag to catch jack stands if necessary any residual fuel remaining in the factory lines 3 Remove the fuel tank Make sure to disconnect all 7 Remove the bolts holding the fuel rail to the intake fittings and wires attached to the fuel tank manifold 2007 Edelbrock Corporation Catalog 641540 Brochure No 63 641540 Page 2 of 5 Rev 10 07 AJ mc FORD EFI 302 COMPLETE KIT FUEL RAIL INSTALL Russell fuel rail install 1 Note Attach supplied brackets to the supplied fuel rails using the supplied hardware Use thread locking compound Install most of the
Download Pdf Manuals
Related Search