Echo ES-255 Blower User Manual
Contents
1. 34 0 mm 1 34 in Stroke 28 0 mm 1 10 in Carburetor Zama Diaphragm model w purge bulb Ignition System Flywheel Magneto capacitor discharge ignition type Spark Plug NGK BPMR8Y Gap 0 65 mm 0 026 in Exhaust System Spark arrestor muffler or spark arrestor muffler with catalyst Fuel Mixed Gasoline and Two stroke Oil Fuel Oil Ratio 50 1 Power Blend X TM ISO L EGD ISO CD 13738 and J A S O M345 FC FD two stroke air cooled engine oil Gasoline Use 89 Octane unleaded Do not use fuel containing methyl alcohol more than 10 ethyl alcohol or 15 MTBE Do not use alternative fuels such as E 15 or E 85 Oil Power Blend X Premium Universal 2 Stroke Oil Fuel Tank Capacity 0 5 lit 16 9 US fl oz Recoil Starter System Automatic Recoil Starter Centrifugal Type Idle Speed RPM2. 2 800 3 200 Wide Open Throttle Speed RPM 6 000 6 500 Maximum Air Speed w pipes MPH 69 3 m sec 155 mph Maximum Air Volume 9 7 m min 342 cu ft min Sound Level at 50 ft dB A scale per ANSI B175 2 70 dB A IMPORTANT This spark ignition system complies with the Canadian standard ICES 002 28 MECHO WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01 01 2010 ECHO S RESPONSIBILITY ECHO Incorporated s Limited Warranty provides to the original purchaser that this ECHO product is free from defects in material and workmanship Under normal use and maintenance from date of purchase ECHO agrees to repair or replace at ECHO s discretion any defective product free of charge at any authorized ECHO servicing dealer within listed below application time periods limitations and exclusions THIS LIMITED WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period Any damage caused by improper installation or improper maintenance is not covered by this warranty All parts or produ
3. WARNING NOTE The safety alert symbol accompanied by the word This enclosed message provides tips for use care WARNING calls attention to an act or condi and maintenance of the unit tion which CAN lead to serious personal injury or death if not avoided IMPORTANT The enclosed message provides information nec A CAUTION essary for the protection of the unit The safety alert symbol accompanied by the word CAUTION calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided INTERNATIONAL SYMBOLS Symbol Symbol Symbol Symbol Symbol form shape Symbol form shape description application Ignition Ignition Read and understand ue Emergency stop OFF ON OFF Fuel and oil mixture Operator s Manual O Finger Severing Carburetoradjustment Wear eyes ears and j Primer bulb mm TT Wear hand Carburetor adjustment Carburetor adjustment Hot protection Use Idle speed High speed mixture Surface two handed pirin nn Tn Wear slip resistant Choke Control Choke Control Safety Alert Cold Start Run y foot wear ot Position Position i Choke Closed Choke Open or sparks near fuel DO NOT smoke near fuel Idle Speed Fast Speed DO NOT allow flames PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING SHRED N VAC users risk injury to themselves and others if the SHRED N VAC is used improperly and or safety precautions are not followed Proper clothing and safety gear must b
4. C with a coin or screwdriver and rotate so that lock symbol A is at top of ring 3 Align locking ribs E on upper blower pipe with recesses D in locking ring and slide upper blower pipe into locking ring 4 After inserting upper blower pipe into fan case so that line F meets locking ring C rotate locking ring clockwise 1 8 turn to lock upper blower pipe in place 5 Align tabs H with grooves G and slide lower blower pipe over upper pipe until there is light resistance Do not force connection 6 Hold upper pipe and turn lower pipe clockwise engaging posi tive locking channels until connection is firm Do not force con nection NOTE Blower use will eventually loosen pipe connections Exclusive positive locking system allows pipes to be tightened If loosening occurs remove lower straight pipe and install according to instruc tions 5 amp 6 blower pipe upper blower pipe lower 10 MECHO VACUUM SHREDDING APPLICATION Remove Blower Pipes 1 Release locking ring C with a coin or screwdriver and rotate ring so that lock symbol A is at top of ring 2 Remove pipes from locking ring Install Vacuum Tube 1 Turn knob I counter clockwise until hinged housing cover is free to open for vacuum tube installation 2 Opening housing cover slide recess J on vacuum tube into locking rib K and turn the vacuum tube clockwise so that it is locked NOTE Engine will not start operat
5. Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor 7 Remove the spark plug and pour 7cc 1 4 oz of fresh clean ECHO 2 stroke engine oil into the cylinder through the spark plug hole A Place a clean cloth over the spark plug hole B Pull the recoil starter handle 2 3 times to distribute the oil inside the engine C Observe the piston location through the spark plug hole Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there 8 Install the spark plug do not connect ignition cable 9 Remove blower vacuum pipes from unit SHRED N VaAc OPERATOR S MANUAL 2 f SPECIFICATIONS MODEL ES 255 Length 340 mm 13 4 in w o pipes Width 260 mm 10 2 in Height 350 mm 13 8 in Weight w blower pipes 4 8 kg 10 6 lb Weight w vac pipes 5 9 kg 13 0 Ib Engine Type Air cooled two stroke single cylinder gasoline engine Displacement 25 4cc 1 55 cu in Botre
6. fuel tank SHRED N Vac OPERATOR S MANUAL Cleaning Cylinder Fins 1 Remove engine cover two screws pull cover away from engine Clean cylinder fins to allow cooling air to pass freely 2 Loosely reassemble engine cover with two screws 3 Tighten all screws securely EXHAUST SYSTEM Spark Arrestor Screen Level 2 Tools required Cross Head Screwdriver 4 mm Hex Wrench Soft metal brush Parts Required Spark arrestor screen Gasket 1 Remove engine cover two screws pull cover away from engine Clean cylinder fins with brush to allow cooling air to pass freely 2 Remove spark arrestor cover A deflector B plate C gasket D and spark arrestor screen E from muffler Replace screen if plugged with carbon deposits NOTE When cleaning carbon deposit be careful not to damage the cata lytic element inside muffler 3 Install spark arrestor screen gasket plate deflector and cover 4 Loosely reassemble engine cover with two screws 5 Tighten all screws securely 21 22 MECHO Exhaust Port Cleaning Level 2 Tools required 4mm Hex Wrench Wood or plastic scraper Parts Required As needed Heat Shield 1 Remove spark plug lead from spark plug and remove engine cover 2 screws 2 Place piston at top dead center Remove muffler A and heat shield B 3 Use a wood or plastic scraping tool to clean deposits from cylin der exhaust port IMPORTANT Never us
7. A to STOP position WARNING If engine does not stop when stop switch is moved to STOP posi tion close choke COLD START position to stall engine Have your ECHO dealer repair stop switch before using blower again 16 MECHO OPERATING BLOWER WARNING Engine exhaust IS HOT and contains Carbon Monoxide CO a poison gas Breathing CO can cause unconsciousness serious in jury or death Exhaust can cause serious burns ALWAYS position unit so that exhaust is directed away from your face and body WARNING Always wear safety glasses hearing protection and a face filter mask or serious personal injury may result Do not point the blower pipe in the direction of people or pets IMPORTANT Use reduced speed only when performing light duty tasks or to comply with local noise regulations Continuous low speed operation may allow fuel oil residue to build up on the piston and cause rapid build up of carbon on the spark arrestor screen resulting in overheating and engine damage To reduce harmful build up run engine at wide open throttle for at least 5 minutes every hour and inspect clean the spark arrestor screen after ap proximately 40 hours of operation Read the Safety Section carefully IMPORTANT To avoid engine damage due to over revving do not block blower pipe 1 Use only during appropriate hours Allow the engine to warm up at a fast idle for a few minutes 3 Control engin
8. Check idle speed and reset if necessary If a tachometer is avail able idle speed screw A should be set to the specifications found on Page 27 Specifications of this manual Turn idle screw A clockwise to increase idle speed counter clockwise to de crease idle speed SHRED N Vac OPERATOR S MANUAL 2 9 TROUBLESHOOTING TROUBLESHOOTING CHART Probe creck sews O cause J Remeay Fuel at carburetor No fuel at carburetor Fuel strainer clogged Clean or replace Fuel line clogged Clean or replace Carburetor See your Echo dealer Fuel at cylinder No fuel at cylinder See your Echo dealer Muffler wet with fuel Fuel Mixture too rich Open choke Engine cranks Clean replace air filter starts hard Adjust carburetor See your Echo dealer doesnt start Spark at end No spark Stop switch off Turn switch to ON of plug wire Electrical problem See your Echo dealer Interlock switch See your Echo dealer Spark at plug No spark Spark gap incorrect Adjust to 65mm 0 026 in Covered with carbon Clean or replace Fouled with fuel Clean or replace Plug defective Replace plug Air Airfiler Air Airfiter dity Airfiter dity Normalwear Normalwear Clean or replace Fuel filter Fuel filter dirty Contaminants residues in Replace fuel Fuel vent vent Fuel vent Fuel vent plugged Contaminants residues in fuel in fuel Clean or Clean or replace Engine runs but dies or Spark Plug Plug dirty worn Clean and adjust or
9. material being vacuumed for best results engine speeds Avoid using vacuum in 4 Empty bag when debris level reaches intake opening To empty areas where rocks or other large hard bag move stop switch to Stop position and wait for blower debris may be vacuumed into unit Clear to stop running Loosen Velcro strap at elbow and slide bag off these areas with blower first blowing elbow Open other end of bag and empty contents Close bag light debris into a pile Use attachment and reattach to blower Secure bag with Velcro strap to vacuum pile SHRED N VAC TROUBLESHOOTING Unit runs but doesn t vacuum or Elbow or debris bag clogged has poor suction Check elbow and debris bag and clear as needed Make sure bag is not folded over at intake during use Obstructions in vacuum tube Check vacuum tube and remove ob structions Avoid wet leaves Unit stopped suddenly during vacu Object stuck in fan housing area Remove vacuum tube and check fan uming and now starter won t work area Remove object Unit jams repeatedly during use Material being vacuumed too big or Use vacuum for leaves and small too hard for blades to shred twigs maximum 1 4 diameter x 3 long Vacuum tube difficult to install or Tube housing fit tight Apply small amount of soapy water remove from unit to end of tube to ease assembly or removal Turns tube 1 4 turn to loosen for removal 18 MECHO MAINTENANCE WARNING Moving
10. must be operated a minimum duration of two tanks of fuel break in before carburetor adjustments can be made During the break in period your engine performance will increase and exhaust emissions will stabilize Idle speed can be adjusted as required High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting emission and durability performance up to 1 100 feet above sea level ASL 96 0 kPa To maintain proper engine operation and emission compliance above 1 100 feet ASL the carburetor may need to be ad justed by an authorized ECHO service dealer IMPORTANT If the engine is adjusted for operation above 1 100 feet ASL the carburetor must be re adjusted when operating the engine below 1 100 feet ASL otherwise severe engine damage may result Level 2 Tools required Screwdriver tachometer Echo P N 99051130017 Parts required None NOTE Every unit is run at the factory and the carburetor is set in compli ance with emission regulations Carburetor adjustments other than idle speed must be performed by an authorized ECHO dealer Idle Adjustment Before adjustment make sure that e Air filter is clean and properly installed e Spark arrestor screen is free of carbon Blower pipes are installed 1 Start engine run at idle for one minute 2 Complete warm up by running at full throttle for 5 minutes oper ating choke twice to clear air from carburetor chambers 3
11. HO Power Blend Two Stroke Oil meets the ISO L EGD and JASO M345 FC FD_ Standard Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two stroke oil used per the statement listed in the EPA or California Emission Defect Warranty Explanation e Damage caused by use of gasohol containing methanol wood alcohol or gasoline containing less than 89 octane Only use gasoline which contains 89 octane or higher Gasohol which contains a maximum 10 ethanol grain alcohol or 15 MTBE methyl tertiary butyl ether is also approved The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator s manual e Engine damage caused by use of ether or any starting fluids e Damage caused by tampering with engine speed governor or emission components or running engines above specified and recommended engine speeds as listed in your operator s manual Operation of the unit with improperly maintained removed cutting shield or removed damaged air filter Damage caused by dirt pressure or steam cleaning the unit salt water corrosion rust varnish abrasives and moisture Defects malfunctions or failures resulting from abuse misuse neglect modifications alterations normal wear improper servicing or use of unauthorized attachments Incorrect storage procedures stale fuel including failure to provide or perform required maintenance services as pres
12. ION Locate the safety decal on your unit Make sure the decals are legible and that you understand and follow the instruc tions on them Ifa decal cannot be read a new one can be ordered from your ECHO dealer See PARTS ORDERING instructions for specific information 1 Hot Decal near muffler and engine P N X505002310 4 General Warning Decal located on Sound Label located on blower blower housing housing P N X505002080 P N X508000130 705 Category Il Measured at 50 ft 15m per ANSI B175 2 8 MECHO SAFETY DECAL Lists important safety precautions STOP SWITCH SLIDE SWITCH mounted on top of handle Push forward to start and run Slide back to stop SPARK PLUG Provides spark to ignite fuel mixture SAFETY DECAL Lists important safety precautions FUEL TANK CAP Covers and seals fuel tank RECOIL STARTER HANDLE Pull recoil handle slowly until recoil starter engages then quickly and firmly When engine starts return handle slowly DO NOT let handle snap back or damage to unit will occur 7 SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST The muffler or catalytic muffler controls exhaust noise and emission The spark arrestor screen prevents hot glowing particles of P ee ae n carbon from leaving the muffler Keep exhaust area clear of flammable debris _ 8 CHOKE Choke is located on top of the air cleaner Move choke lever to COLD START x to close choke for co
13. Itis a dealer s and or customer s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting WWW ECHO USA COM Your receipt of purchase including date model and serial number must be maintained and presented to an authorized ECHO servicing dealer for warranty service Proof of purchase rests solely with the customer Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so you may also have other specific legal rights which vary from state to state This limited warranty is given by ECHO Incorporated 400 Oakwood Rd Lake Zurich IL 60047 DISCLAIMER OF IMPLIED WARRANTIES This limited warranty is in lieu of all other expressed or implied warranties including any warranty of FITNESS FOR A PARTICULAR PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product ECHO and its affiliated companies shall not be liable for any special incidental or consequential damage including lost profits There are no warranties extended other than as provided herein This limited warranty may be modified only by ECHO 99922201032 12 03 09 30 MECHO ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency EPA and the California Air Resources Bo
14. MECHO SHRED N VAC Operator s Manual MODEL ES 255 AY WARNING A A WARNING A The muffler or catalytic muffler The engine exhaust from this and surrounding cover may become product contains chemicals known Wibi extremely hot to the State of California to cause Always keep clear of exhaust and muffler area cancer birth defects or other otherwise serious personal injury may occur reproductive harm WARNING Read rules for safe operation and instructions carefully ECHO provides this Operator s Manual which must be read and understood for proper and safe opera tion X750011944 X7501180704 11109 2 MECHO INTRODUCTION Welcome to the ECHO family This ECHO product was designed and manufactured to provide long life and on the job dependability Read and understand this manual You will find it easy to use and full of helpful operating tips and SAFETY messages THE OPERATOR S MANUAL HECHO Read and understand this manual before operation Keep it in a safe SHRED VAG place for future reference It contains specifications and information for operation starting stopping maintenance storage and assembly specific to this product TABLE OF CONTENTS Maintenance Skill Levels Maintenance Intervals Manual Safety Symbols and Important Air Filter Information Fuel Filter International Symbols Spark Plug Personal Condition and Safety Equipment Cooling System Equipment Check Exhaust S
15. TS do the following Avoid using your wrist in a bent extended or twisted position Instead try to maintain a straight wrist position Also when grasping use your whole hand not just the thumb and index finger Take periodic breaks to minimize repetition and rest your hands Reduce the speed and force with which you do the repetitive movement Do exercises to strengthen the hand and arm muscles Immediately stop using all power equipment and consult a doc tor if you feel tingling numbness or pain in the fingers hands wrists or arms The sooner RSI CTS is diagnosed the more likely permanent nerve and muscle damage can be prevented DANGER Do not operate this product indoors or in inadequately ventilated areas Engine exhaust contains poisonous emissions and can cause serious injury or death Read the Manuals e Provide all users of this equipment with the Operator s Manual and Safety Manual for instructions on Safe Operation Clear the Work Area e Spectators and fellow workers must be warned and children and animals prevented from coming nearer than 15 m 50 ft while the unit is in use e Take wind conditions into account avoid open doors and win dows Do not point blower at people or animals SS Review area to be cleared Look for potential hazards such as stones or metal objects Keep a Firm Grip e Hold the handle in one hand with thumb and fingers encircling the handle Keep a Solid St
16. VERED PART BE CORRECTED If there is a defect in a part covered by this warranty any ECHO Inc Authorized Service Dealer will correct the defect You will not have to pay anything to have the part adjusted repaired or replaced This includes any labor and diagnosis for warranted repairs performed by the dealer In addition engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted WHAT PARTS ARE COVERED Any applicable emission related part not scheduled for required maintenance will be repaired or replaced within the warranty period The repaired or replaced part will be warranted for the remaining ECHO Inc warranty period Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc warranty period Any emission related part scheduled for replacement during required maintenance is warranted for the period of time prior to the first scheduled replacement point for that part Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the first scheduled replacement point for that part Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts and must be pr
17. ance e Maintain footing and balance at all times Do not stand on slip pery uneven or unstable surfaces Do not work in odd positions or on ladders Do not over reach Avoid Hot Surfaces e Keep exhaust area clear of flammable debris Avoid contact dur ing and immediately after operation 6 UUELAG EQUIPMENT CHECK WARNING Use only ECHO approved attachments Serious injury may result from the use of a non approved attachment combi nation ECHO INC will not be responsible for the failure of cutting devices attachments or accessories which have not been tested and approved by ECHO Read and comply with all safety instructions listed in this manual and safety manual Check unit for loose missing nuts bolts and screws Tighten and or replace as needed Do not use blower if any part is missing or damaged Have repairs done only by an authorized ECHO Service dealer Do not use any attachment accessory or replacement part unless it is recommended in this Operator s Manual WARNING Moving parts can amputate fingers or cause severe injuries Keep hands clothing and loose objects away from all openings e ALWAYS stop engine disconnect spark plug and make sure all moving parts have come to a complete stop before removing obstructions clearing debris or servicing unit e DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit e NEVER reach into any opening wh
18. ard C A R B and ECHO Incorporated ECHO Inc are pleased to explain the emission control system warranty on your 2010 and later equipment small off road engine SORE New equipment SORE must be designed built and equipped to meet stringent EPA and C A R B anti smog standards ECHO Inc must warrant the emission control system on your equipment SORE for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your equipment SORE Your emission control system may include parts such as carburetor fuel injection system ignition system catalytic converter muffler fuel tank fuel feed lines fuel cap assembly spark plug air filters and other associated components Where a warrantable condition exists ECHO Inc will repair your equipment SORE at no cost to you including diagnosis parts and labor The Emission Control System warranty is extended to the original owner including all subsequent owners MANUFACTURER S WARRANTY COVERAGE The emission control system is warranted for 2 years or the length of the ECHO Inc warranty whichever is longer If any emission related part on your equipment is defective the part will be repaired or replaced by ECHO Inc or its Authorized Service Representative OWNER S WARRANTY RESPONSIBILITIES As the equipment SORE owner you are responsible for the performance of the required maintenance listed in your Operator s Manual ECHO Inc recommends that you retain all rece
19. cribed in the operator s manual Preventative maintenance as outlined in the operators manual is the customer s responsibility Failures due to improper set up pre delivery service or repair service by anyone other than authorized ECHO servicing dealer during the warranty period e Certain parts and other items are not warranted including but not limited to lubricants starter cords and engine tune ups Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator s Manuals e Overheating or carbon scoring failures due to restricted clogged exhaust port or combustion chamber including damage to spark arrester screen Adjustments after the first 30 thirty days and beyond such as carburetor adjustment and throttle cable adjustment e Damage to gears or gear cases caused by contaminated grease or oil use of incorrect type or viscosity of lubricants and or failure to comply with recommended grease or oil change intervals e Damage caused by loading SHRED N VAC beyond recommended capacity Damage caused by pump or sprayer running dry pumping or spraying caustic or flammable materials or lack of or broken strainers Additional damage to parts or components due to continued use after operational problem or failure occurs Should operational problem or failure occur the product should not be used but delivered as is to an authorized ECHO servicing dealer
20. cts replaced under warranty become the property of ECHO Inc This warranty is separate from the Emission control warranty statement supplied with your new product Please consult the Emission Control Warranty Statement for details regarding emission related parts For a list of Authorized ECHO Dealers refer to WWW ECHO USA COM or call 1 800 432 ECHO OWNER S RESPONSIBILITY To ensure trouble free warranty coverage it is important that you register your ECHO equipment on line at WWW ECHO USA COM or by fill ing out the warranty registration card supplied with your unit Registering your product confirms your warranty coverage and provides a direct link if we find it necessary to contact you The owner shall demonstrate reasonable care and use and follow preventative maintenance storage fuel and oil usage as prescribed in the operator s manual Should a product difficulty occur you must at your expense deliver or ship your ECHO unit to an authorized ECHO servicing dealer for warranty repairs within the applicable warranty period and arrange for pick up or return of your unit after the repairs have been made For your nearest authorized ECHO servicing dealer call ECHO s Dealer Referral Center at 1 800 432 ECHO or you can locate an ECHO servicing dealer at WWW ECHO USA COM Should you require assistance or have questions concerning ECHO s Warranty Statement you can contact our Consumer Product Support Department at 1 800 673 1558 or contact u
21. d cold Exposure to vibration and cold may cause tingling and burning sen sations followed by loss of color and numbness in the fingers The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown e Keep your body warm especially the head neck feet ankles hands and wrists Maintain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not smoking e Limit the hours of operation Try to fill each day with jobs where operating the unit or other hand held power equipment is not required If you experience discomfort redness and swelling of the fingers followed by whitening and loss of feeling consult your physician before further exposing yourself to cold and vibration SHRED N Vac 5 OPERATOR S MANUAL Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers hands arms and shoulders may cause soreness swelling numbness weakness and extreme pain in those areas Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury RSI An extreme RSI condition is Carpal Tunnel Syndrome CTS which could occur when your wrist swells and squeezes a vital nerve that runs through the area Some believe that prolonged exposure to vibration may contribute to CTS CTS can cause severe pain for months or even years To reduce the risk of RSI C
22. e a metal tool to scrape carbon from the exhaust port Do not scratch the cylinder or piston when cleaning the exhaust port Do not allow carbon particles to enter the cylinder Inspect heat shield and replace if damaged 5 Install heat shield and muffler 6 Tighten muffler mounting bolts or nuts to 60 70 inelbf 70 80 kgfecm 7 Install engine cover and attach spark plug lead 8 Start engine and warm to operating temperature 9 Stop engine and re tighten mounting bolts or nuts to specifica tions SHRED N VAc OPERATOR S MANUAL 2 3 SHREDDER BLADE Level 1 A WARNING Never remove vacuum tube or open fan guard when SHRED N VAC is running or serious personal injury may result Always wear heavy duty work gloves when working in shredder blade area 1 With engine stopped remove spark plug wire remove vacuum tube from unit 2 Remove accumulated debris from blade and inspect for damage IMPORTANT Do not operate SHRED N VAC if shredder blade is damaged or broken Return unit to Echo Dealer for service 3 Install vacuum tube Refer to Install Vacuum Tube and Bag Assembly page 9 in assembly section for correct assembly procedures DEBRIS BAG Level 1 Parts Required None Shake dust from bag and inspect for hole or tears Inspect zipper and clean debris from teeth to assure complete closing of zipper 24 WECHO CARBURETOR ADJUSTMENT Engine Break In New engines
23. e speed with throttle trigger F or for continu ous use set engine speed with throttle position lever B Rotate throttle position lever forward for lower speed back for higher speed 4 Use lower speed to blow debris from hard surfaces 5 Additional speed may be necessary to clean debris snow etc from lawns and flowerbeds NOTE Never use a higher speed setting than necessary to perform a task Remember the higher the engine speed the louder the blower noise Minimize dust by using blower at lower speeds Keep debris on your property Be Smart be a good neighbor SHRED N VaAc 1 7 OPERATOR S MANUAL SHRED N VAC OPERATION WARNING Flying debris hazard Never operate unit as a vacuum unless discharge elbow is installed and debris bag is securely cinched to elbow Failure to follow instructions can result in serious injuries WARNING Debris bag is flammable and could be ignited if allowed to contact hot muffler cover or exhaust Keep bag away from hot surfaces at all times 1 Adjust debris bag strap to support bag on operator s shoulder Bag must not be folded at intake area or intake will clog Further adjustment may be necessary as the debris bag fills and becomes heavier 2 Grip throttle control handle with left hand and lower handle stand with right hand NOTE 3 Operate unit with beveled end of tube facing downward Keep Vacuum action works best at higher tube opening close to
24. e unless safety interlock switch K is activated by the vacuum tube SHRED N VaAc 1 1 OPERATOR S MANUAL Install Bag 1 Stand unit upright on blower base 2 Release locking ring C with a coin or screwdriver and rotate so that lock symbol A is at top of ring 3 Align locking ribs L on elbow with recesses D in locking ring and slide elbow into locking ring 4 After inserting elbow into fan case so that line M meets locking ring C rotate locking ring clockwise 1 8 turn to lock elbow in place 5 Place debris bag opening over flared end of elbow and cinch bag O securely at the position N with Velcro strap 12 MECHO OPERATION WARNING Moving parts can amputate fingers or cause severe injuries Keep hands clothing and loose objects away from all openings Always stop engine disconnect spark plug and make sure all moving parts have come to a complete stop before removing obstructions clearing debris or servicing unit Blower housing may contain shredder blades and other sharp edges that can cause serious injuries if touched even if engine is off and blades are not moving Wear gloves to protect hands from sharp edges and hot surfaces A WARNING Operation of this equipment may create sparks that can start fires around dry vegetation This unit is equipped with a spark arrestor and a spark arrestor may be required The operator should contact local fire agencies for laws or regulat
25. e worn when operating SHRED N VAC 4 MECHO Physical Condition Your judgment and physical dexterity may not be good if you are tired or sick if you are taking medication if you have taken alcohol or drugs Operate unit only if you are physically and mentally well Eye Protection Wear eye protection that meets ANSI Z87 1 or CE requirements whenever you operate the unit Hand Protection Wear no slip heavy duty work gloves to improve your grip on the blower handle Gloves also reduce the transmission of machine vibration to your hands Breathing Protection Wear a facemask to protect against dust Hearing Protection ECHO recommends wearing hearing protection whenever unit is used Proper Clothing Wear snug fitting durable clothing e Pants should have long legs shirts with long sleeves DO NOT WEAR SHORTS DO NOT WEAR TIES SCARVES and JEWELRY Wear sturdy work shoes with nonskid soles DO NOT WEAR OPEN TOED SHOES DO NOT OPERATE UNIT BAREFOOTED Keep long hair away from engine and blower intake Retain hair with cap or net Hot Humid Weather Heavy protective clothing can increase operator fatigue which may lead to heat stroke Schedule heavy work for early morning or late afternoon hours when temperatures are cooler Vibration and Cold It is believed that a condition called Raynaud s Phenomenon which affects the fingers of certain individuals may be brought about by exposure to vibration an
26. ement for Life free of charge for a period of ten 10 years after the date of the complete unit s final production SHRED N Vac OPERATOR S MANUAL 2 9 PURCHASED REPAIR PARTS SHORT BLOCKS AND ACCESSORIES 90 day residential or non income producing warranty 30 day commercial institutional agricultural industrial income producing or rental application warranty ATTENTION TWO STROKE ENGINE POWER PRODUCT OWNERS This ECHO two stroke engine power product is a quality engineered unit which has been manufactured to exact tolerances to provide superior performance To help ensure the performance of the unit it is required to use two stroke oil which meets the ISO L EGD Standard per ISO CD 13738 and JASO M345 FC FD Standards ECHO Power Blend Two Stroke Oil is a premium two stroke oil specifically formulated to meet ISO L EGD ISO CD 13738 and JASO M345 FC FD Standards The use of two stroke oils designed for other applications such as for outboard motors or lawnmowers can result in severe engine damage and will void your two stroke engine limited warranty THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY e Lack of lubrication or engine failure due to the use of two stroke oils that do not meet the ISO L EGD ISO CD 13738 and JASO M345 FC FD Standards Engine problems due to inadequate lubrication caused by failure to use an ISO L EGD compliant and JASO M345 FC ED registered oil will void the two stroke engine limited warranty EC
27. ency of required maintenance MAINTENANCE PROCEDURE NOTES 1 Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity All recommendations to replace are based on the finding of damage or wear during inspection SHRED N VaAc 1 9 OPERATOR S MANUAL AIR FILTER Level 1 Tools required 25 50 mm 1 2 in Cleaning brush Parts required REPOWER AIR amp FUEL FILTER KIT NOTE Clean daily 1 Close choke Cold Start Position Ap This prevents dirt from entering the carburetor throat when the air filter is removed Brush accumulated dirt from air cleaner area 2 Remove air filter cover Brush dirt from inside cover 3 Remove air filter and lightly brush debris from filter Replace filter if it is damaged fuel soaked very dirty or the rubber sealing edges are deformed 4 If filter can be reused be certain it e Fits tightly in the air filter cavity e Is installed with the original side out 5 Install air filter cover FUEL FILTER Level 1 Tools required 200 250 mm 8 10 in length of wire with one end bent into a hook Clean rag funnel and an approved fuel container Parts required REPOWER AIR amp FUEL FILTER KIT DANGER Fuel is VERY flammable Use extreme care when mixing storing or handling 1 Usea clean rag to remove loose dirt from around fuel cap and empty fuel tank 2 Use the fuel line hook to pull the fuel line and fi
28. handle rope E until en gine fires or maximum 5 pulls 6 Choke __ Move choke lever C to Run position if necessary restart engine NOTE If engine does not start after 5 pulls repeat instructions 3 6 7 After engine warm up gradually depress throttle trigger to in crease engine RPM to operating speed NOTE Allow engine to warm up before use SHRED N VAc 1 5 OPERATOR S MANUAL STARTING WARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke 1 Stop Switch Move stop switch button A away from the STOP position 2 Throttle Position Lever Move throttle position lever B midway between idle and full throttle positions 3 Purge Bulb Pump purge bulb D until fuel is visible and flows freely in the clear fuel tank return line 4 Recoil Starter Place the unit on a flat clear area Firmly grasp throttle grip with left hand and rapidly pull recoil starter handle rope E until en gine fires IMPORTANT Recoil starter Use short pulls only 1 2 2 3 of rope for start ing Do not allow the rope to snap back in Always hold the unit firmly NOTE If engine does not start after 5 pulls use Cold Start Procedure STOPPING ENGINE 1 Throttle Trigger Throttle Position Lever Release throttle trigger F Move throttle position lever B forward to idle position and allow engine to return to idle before shutting off engine 2 Stop Switch Move stop switch
29. ilable from your ECHO dealer or at www echo usa com or by contacting ECHO Inc 400 Oakwood Road Lake Zurich IL 60047 800 673 1558 Always check the ECHO Web Site for updated information Safety Videos are available from your Echo dealer A 5 00 shipping charge will be required for each video MECHO ECHO INCORPORATED 400 Oakwoop Roap LAKE ZurRicH IL 60047 1564 www echo usa com P07213001001 P07213999999
30. ile the engine is running Moving parts may not be visible through openings WARNING Check fuel system for leaks due to fuel tank damage especially if the unit is dropped If damage or leaks are found do not use unit otherwise serious personal injury or property damage may occur Have unit repaired by an authorized servicing dealer before using EMISSION CONTROL EXHAUST amp EVAPORATIVE EPA 2010 and Later The emission control system for the engine is EM TWC Engine Modification and 3 way Catalyst and for the fuel tank the Control System is EVAP Evaporative Emissions or N for nylon tank Evaporative emission may be applicable to California models only EMISSION CONTROL INFORMATION ENGINE FAMILY HEHXS O45 KA DISPLACEMENT 45 0cc EMISSIOK COMPLIANCE PERIOD 300 HOURS THIS ENGINE MEETS LLS EPA EXVEV REGS POR MODEL TEME E f REFER TO OWNERS MANUAL FOR MAINTENANCE An Emission Control Label is located on the unit This is SPECIFICATIONS AND ADJUSTMENTS an EXAMPLE ONLY information on label varies by engine YAMABIKO CORP 7 E FAMILY PRODUCT EMISSION DURABILITY EMISSION COMPLIANCE PERIOD The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis sions output meets applicable emissions regulations provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual SHRED N Vac 7 OPERATOR S MANUAL DESCRIPT
31. ions relating to fire prevention requirements FUEL NOTICE Use of unmixed improperly mixed or fuel older than 90 days stale fuel may cause hard starting poor performance or severe engine damage and void the product warranty Read and follow instructions in the Storage section of this manual WARNING Alternative fuels such as E 15 15 ethanol E 85 85 ethanol or any fuels not meeting ECHO requirements are NOT approved for use in ECHO 2 stroke gasoline engines Use of alternative fuels may cause performance prob lems loss of power overheating fuel vapor lock and unintended machine operation including but not limited to improper clutch engagement Alternative fuels may also cause premature deterioration of fuel lines gaskets carbu retors and other engine components Fuel Requirements Gasoline Use 89 Octane R M 2 mid grade or higher gasoline known to be good quality Gasoline may contain up to 10 Ethanol grain alcohol or 15 MTBE methyl tertiary butyl ether Gasoline containing methanol wood alcohol is NOT approved Two Stroke Oil A two stroke engine oil meeting ISO L EGD ISO CD 13738 and J A S O FC FD Standards must be used Echo brand premium Power Blend X Universal 2 Stroke Oil meets these standards Engine problems due to inadequate lubrication caused by failure to use an ISO L EGD ISO CD 13738 and J A S O FC FD certified oil such as Echo premium Power Blend X will void the two st
32. ipts covering maintenance on your equipment SORE however ECHO Inc cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance As the equipment SORE owner you should be aware that ECHO Inc may deny you warranty coverage if your equipment SORE or a part has failed due to abuse neglect improper maintenance or unapproved modifications You are responsible for presenting your equipment SORE to an ECHO Inc authorized service representative as soon as a problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If a warrantable condition exists and there is no Authorized Dealer within 100 miles ECHO Inc will pay to ship the unit to the nearest authorized dealer If you have questions regarding your warranty coverage you should contact ECHO Inc at 1 800 673 1558 web site WWW ECHO USA COM or contact Shindaiwa at 1 877 986 7783 web site WWW SHINDAIWA COM WHAT DOES THIS WARRANTY COVER ECHO Inc warrants that your equipment SORE was designed built and equipped to conform with applicable EPA and C A R B emissions standards and that your equipment SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable requirements for 2 years or the length of the ECHO Inc warranty whichever is longer The warranty period begins on the date the product is purchased by an end user HOW WILL A CO
33. ite them in the space provided below Model No SN SERVICE Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer For the name and address of the Authorized ECHO Service Dealer nearest you ask your retailer or call 1 800 432 ECHO 3246 Dealer information is also available on our Web Site When presenting your unit for Warranty service repairs proof of purchase is required ECHO CONSUMER PRODUCT SUPPORT If you require assistance or have questions concerning the applica tion operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1 800 673 1558 from 8 30 am to 4 30 pm Central Standard Time Monday through Friday Before calling please know the model and serial number of your unit WARRANTY REGISTRATION To ensure trouble free warranty coverage it is important that you regis ter your ECHO equipment on line at www echo usa com or by filling out the warranty registration card supplied with your unit Registering your product confirms your warranty coverage and provides a direct link between you and ECHO if we find it necessary to contact you ADDITIONAL OR REPLACEMENT MANUALS s 53 q TAMABIKO CORP AGO usa Hes DEALER Call 1 800 432 ECHO 1 800 432 3246 or www echo usa com CONSUMER PRODUCT SUPPORT 1 800 673 1558 8 30 4 30 Mon Fri C S T Replacement Operator Safety Manuals and Parts Catalogs are ava
34. ld starting Move choke lever to RUN position to open choke 9 PURGE BULB Pumping purge bulb before starting engine draws fresh fuel from the fuel tank purging air from the carburetor Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line Pump purge bulb an additional 4 or 5 times 10 BLOWER PIPES Exclusive positive locking system 11 THROTTLE POSITION LEVER Pull back to increase engine speed Friction washers maintain throttle lever setting 12 THROTTLE TRIGGER Spring loaded to return to idle when released During acceleration press trigger gradu ally for best operating technique 13 AIR CLEANER Contains replaceable air filter element 14 LOCKING RING Locks blower pipe 15 SHOULDER STRAP Secures debris bag to sholder 16 VACUUM TUBE Sucks in materials to be shredded 17 DEBRIS BAG Collects shredded material CONTENTS L Power Head Blower Pipe upper Blower Pipe lower SHRED N VAC Suction Tube Elbow Pipe Debris Bag Operator s Manual Warranty Registration Card Echo Power Blend X 2 stroke oil sample 1 1 1 1 l l l l l SHRED N Vac 9 OPERATOR S MANUAL ASSEMBLY WARNING Never perform maintenance or assembly procedures with engine running or serious personal injury may result BLOWER APPLICATION Install Blower Pipes 1 Stand unit upright on blower base 2 Release locking ring
35. lter from the tank 3 Remove the filter from the line and install the new filter 20 MECHO SPARK PLUG Level 2 Tools required T Wrench Feeler gauge Parts Required REPOWER Tune Up Kit IMPORTANT Use only NGK BPM8Y spark plug otherwise severe engine damage may occur 1 Remove spark plug and check for fouling worn and rounded center electrode 2 Clean the plug or replace with a new one DO NOT sand blast to clean Remaining sand will damage engine 0 026 in 3 Adjust spark plug gap by bending outer electrode 4 Tighten spark plug to 150 170 kgf cm 130 150 in Ibf COOLING SYSTEM Level 2 Tools required 25 50 mm 1 2 in cleaning brush 4 mm Hex Wrench Parts Required None if you are careful IMPORTANT To maintain proper engine operating temperatures cooling air must pass freely through the cylinder fin area This flow of air carries combustion heat away from the engine Overheating and engine seizure can occur when Air intakes are blocked preventing cooling air from reaching the cylinder e Dust and grass build up on the outside of the cylinder This build up insulates the engine and prevents the heat from leaving Removal of cooling passage blockages or cleaning of cooling fins is considered Normal Maintenance Any failure attributed to lack of maintenance is not warranted Cleaning Grill 1 Brush accumulated debris from crankcase intake grill above the
36. ovided without charge if the part is still under warranty Any replacement part that is equivalent in performance and durability may be used in non warranty maintenance or repairs and shall not reduce the warranty obligations of the manufacturer Throughout the equipment SORE warranty period ECHO Inc will maintain a supply of warranted parts sufficient to meet the expected demand for such parts SPECIFIC EMISSION RELATED WARRANTED PARTS Electronic Ignition System Spark Plug e Catalytic Converter Muffler Assembly e Carburetor complete assembly or replaceable components e Choke Fuel Injection Assembly or replaceable components Fuel Tank Fuel Cap Assembly e Air Filter e Fuel Feed Line and associated clamps connectors as applicable WHAT IS NOT COVERED Any failure caused by abuse neglect improper maintenance unapproved modifications use of unapproved add on parts modified parts or unapproved accessories This Emission Control Warranty is valid only for the U S A it s Territories and Canada 99922201033 01 2010 SHRED N Vac 3 1 OPERATOR S MANUAL NOTES SERVICING INFORMATION PARTS SERIAL NUMBER Genuine ECHO Parts and ECHO REPOWER Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer When you do need to buy parts always have the Model Num ber Type and Serial Number of the unit with you You can find these numbers on the engine housing For future reference wr
37. parts can amputate fingers or cause severe injuries Keep hands clothing and loose objects away from all openings Always stop engine disconnect spark plug and make sure all moving parts have come to a complete stop before removing obstructions clearing debris or servicing unit Allow unit to cool before performing service Wear gloves to protect hands from sharp edges and hot surfaces Your ECHO blower is designed to provide many hours of trouble free service Regular scheduled maintenance will help your blower achieve that goal If you are unsure or are not equipped with the necessary tools you may want to take your unit to an ECHO Service Dealer for maintenance To help you decide whether you want to DO IT YOURSELF or have the ECHO Dealer do it each maintenance task has been graded If task is not listed see your ECHO Dealer for repairs SKILL LEVEL Levell Easy to do Common tools may be required Level2 Moderate difficulty Some specialized tools may be required ECHO offers REPOWER Maintenance Kits and Parts to make your maintenance job easier MAINTENANCE INTERVALS MAINTENANCE DAILY OR COMPONENT SYSTEM PROCEDURE BEFORE USE Inspect Clean Cooling System Muffler Spark Arrestor Cylinder Exhaust Port Recoil Starter Rope Screws Nuts Bolts MAINTENANCE PROCEDURE LETTER CODES I INSPECT R REPLACE C CLEAN IMPORTANT NOTE Time intervals shown are maximum Actual use and your experience will determine the frequ
38. replace does not properly Cooling System Cooling system Extended operation in Clean dirty plugged dirty dusty locations Spark Arrestor Screen Spark arrestor screen Normal wear Replace plugged Engine does N A N A Internal engine problem See your Echo dealer not crank Engine runs Blower pipe Pipe clogged Build up of debris Unclog blower doesn t weak uneven DANGER Fuel vapors are extremely flammable and may cause fire and or explosion Never test for ignition spark by ground ing spark plug near cylinder plug hole otherwise serious personal injury may result 26 MECHO STORAGE WARNING During operation the muffler or catalytic muffler and surrounding cover becomes hot Always keep exhaust area clear of flammable debris during transportation or when storing otherwise serious property damage or personal injury may result Long Term Storage Over 30 Days Do not store your unit for a prolonged period of time 30 days or longer without performing protective storage mainte nance which includes the following 1 Store unit in a dry dust free place out of the reach of children DANGER Do not store where fuel fumes may accumulate or reach an open flame or spark 2 Place the stop switchs in the STOP position 3 Remove accumulation of grease oil dirt and debris from exterior of unit 4 Perform all periodic lubrication and services that are required 5 Tighten all screws and nuts 6
39. roke engine warranty IMPORTANT Echo premium Power Blend X TM Universal 2 Stroke Oil may be mixed at 50 1 ratio for application in all Echo en gines sold in the past regardless of ratio specified in those manuals SHRED N VaAc 1 3 OPERATOR S MANUAL Handling Fuel DANGER Fuel is VERY flammable Use extreme care when mixing storing or handling or serious personal injury may result e Use an approved fuel container DO NOT smoke near fuel DO NOT allow flames or sparks near fuel e Fuel tanks cans may be under pressure Always loosen fuel caps slowly allowing pressure to equalize e NEVER refuel a unit when the engine is HOT or RUNNING e DO NOT fill fuel tanks indoors ALWAYS fill fuel tanks outdoors over bare ground e DO NOT overfill fuel tank Wipe up spills immediately e Securely tighten fuel tank cap and close fuel container after refueling e Inspect for fuel leakage If fuel leakage is found do not start or operate unit until leakage is repaired Move at least 3m 10 ft from refueling location before starting the engine Mixing Instructions 1 Fill an approved fuel container with half of the required amount Fuel to Oil Mix 50 1 Ratio of gasoline 2 Add the proper amount of 2 stroke oil to gasoline METRIC 3 Close container and shake to mix oil with gasoline Ves Toes To 4 Add remaining gasoline close fuel container and remix Liter After use hel pe DO NOT store a unit with fuel in its
40. s through the web at WWW ECHO USA COM PRODUCT WARRANTY PERIOD RESIDENTIAL APPLICATION 5 YEAR WARRANTY All units for residential or non income producing use will be covered by this limited warranty for five 5 years from date of purchase EXCEPTIONS For two stroke engine powered products the electronic ignition module flexible drive cables SRM solid drive shafts and TC tines are warranted for the life of the product on parts only e Cutting attachments such as but not limited to bars chains sprockets blades and nylon trimmer heads for residential or non income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date Any misuse from contact with concrete rocks or other structures is not covered by this warranty ECHO s Rapid Loader String Head carries a lifetime warranty on the line locking system parts only no labor Refer to your operator s manual for string head installation and maintenance instructions All SB Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit COMMERCIAL APPLICATION 1 YEAR WARRANTY All Chain Saws QuikVent Saws and Cut Off Saws for commercial institutional agricultural industrial or income producing use will be covered by this limited warranty for one 1 year from the date of purchase 2 YEAR WARRANTY All other uni
41. tank Leaks can occur Return unused fuel to an approved fuel storage container Shoulder IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions Some states may require the use of automatic fuel shut off containers to reduce fuel spillage Storage Fuel storage laws vary by locality Contact your local gov ernment for the laws affecting your area As a precaution store fuel in an approved airtight container Store in a well ventilated unoccupied building away from sparks and flames IMPORTANT Stored fuel ages Do not mix more fuel than you expect to use in thirty 30 days ninety 90 days when a fuel stabilizer is added IMPORTANT Stored two stroke fuel may separate ALWAYS shake fuel con tainer thoroughly before each use 14 MECHO STARTING COLD ENGINE 1 Stop Switch Move stop switch button A away from the STOP position 2 Throttle Position Lever Move throttle position lever B midway between idle and full throttle positions 3 Choke Move choke C to Cold Start AS Position 4 Purge Bulb Pump purge bulb D until fuel is visible and flows freely in the clear fuel tank return line IMPORTANT Recoil starter Use short pulls only 1 2 2 3 of rope for start ing Do not allow the rope to snap back in Always hold the unit firmly 5 Recoil Starter Place the unit on a flat clear area Firmly grasp throttle grip with left hand and rapidly pull recoil starter
42. ts for commercial institutional agricultural industrial or income producing use will be covered by this limited warranty for two 2 years from the date of purchase EXCEPTIONS For two stroke engine powered products the electronic ignition module flexible drive cables SRM solid drive shafts and TC tines are warranted for the life of the product on parts only e Cutting attachments such as but not limited to bars chains sprockets blades and nylon trimmer heads for commercial institutional agricultural industrial rental or income producing will be covered for failures due to defects in material or workmanship for a period of 30 days from original product purchase date Any misuse from contact with concrete rocks or other structures is not covered by this warranty ECHO s Rapid Loader String Head carries a lifetime warranty on the line locking system parts only no labor Refer to your operator s manual for string head installation and maintenance instructions e All SB Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit RENTAL APPLICATION 90 DAYS WARRANTY e Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase ECHO s liability under the Lifetime coverage is limited to furnishing parts specified under the PRODUCT WARRANTY PERIOD section of this warranty stat
43. ystem Emission Control Shredder Blade Description Debris Bag Contents Carburetor Adjustment High Altitude Operation Troubleshooting Storage Specifications Warranty Statements Starting Cold Engine Servicing Information Starting Warm Engine Parts Serial Number Stopping Engine Service Operating Blower ECHO Consumer Product Support SHRED N VAC Operation Warranty Registration SHRED N VAC Troubleshootin Additional or Replacement Manuals Specifications descriptions and illustrative material in this literature are as accurate as known at the time of publica tion but are subject to change without notice Illustrations Copyright 2010 By Echo Incorporated may include optional equipment and accessories and may All Rights Reserved not include all standard equipment SHRED N Vac 3 OPERATOR S MANUAL SAFETY MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION Throughout this manual and on the product itself you will find safety alerts and helpful informational messages pre ceded by symbols or key words The following is an explanation of those symbols and key words and what they mean to you The safety alert symbol accompanied by the word This symbol means the specific action DANGER calls attention to an act or condition shown is prohibited Ignoring these prohi which WILL lead to serious personal injury or bitions can result in serious or fatal injury death if not avoided DANGER S CIRCLE AND SLASH SYMBOL
Download Pdf Manuals
Related Search