Dynex DX-SB114 Home Theater System User Manual
Contents
1. Back of the soundbar 3 5 mm audio cable included TV projector or Back of the soundbar DVD Blu ray player OUTPUT RCA audio cable included Back of the soundbar CONNECT THE SUBWOOFER OPTIONAL Connect one end of the subwoofer speaker cable not included to the subwoofer and the other end to the soundbar Subwoofer Subwoofer cable not included CONNECT THE AC ADAPTER CAUTIONS e Make sure that the electrical outlet matches the AC adapter s input requirements of 100 240 V 50 60 Hz before connecting e Use only the AC adapter provided e Plug in the AC adapter only after all other connections have been made 1 Connect the AC adapter to the DC IN jack on the back of the soundbar 2 Plug the other end of the AC adapter into a power outlet or surge protector Back of the soundbar SUBWOOFER OUT POSITION YOUR SOUNDBAR You can mount your soundbar on the wall You can set the soundbar on a flat surface go to Step 5 go to Step 6 MOUNTING YOUR SOUNDBAR ON A WALL OPTIONAL YOU WILL NEED Screws 2 Measuring tape 10 wood screw or similar N S 11 2 length Wall Mounting template Pencil Level Stud finder Drill and Screwdriver Q di optional for wood drill bit rammer Croo stud installation Tape Wall anchors 2 NOTE Mounting instructions are also provided on the wall mounting template 1 Selecta location close to your TV and directly in front of the vie2. 2 After connecting power see USING YOUR SOUNDBAR on the next page Press to turn on the soundbar Press again to return the soundbar to standby mode BASS button and indicator Press to activate the bass frequency enhancement The indicator lights green Press again to turn off the bass frequency enhancement VOL buttons Press to increase or decrease the volume of the soundbar BASS button Press to activate the bass frequency enhancement pages aa Me souncharmvawal NOTE Make sure the cable ends match the color of the ports VOL buttons Press to increase or decrease the volume of the soundbar SUBWOOFER OUT a ONARE A DOVES SETOS Jolt 4 x Mute button Press to mute the sound from the soundbar Press again to DCIN jack Connect the AC adapter to this jack to power the soundbar restore the sound Choose one connection option below that fits your audio source device e g TV projector CAUTION Turn off or unplug all devices while you are making connections NOTE If you have multiple devices connected to a TV or projector connecting directly to the TV or projector will ensure audio plays through your soundbar from all of your devices CABLE e r a RCA Audio cable included TV projector or DVD Blu ray player OUTPUT DIGITAL OPTICAL Back of the soundbar Digital optical cable not included TV projector or DVD Blu ray player OUTPUT Q AUDIO
3. 5 2204 U S and Canada or 01 800 926 3020 Mexico www dynexproducts com O ON A UU BRWHDN DYNEX is a trademark of Best Buy and its affiliated companies Registered in some countries Distributed by Best Buy Purchasing LLC 7601 Penn Ave South Richfield MN 55423 U S A 2014 Best Buy All rights reserved Made in China V1 ENGLISH 14 0550
4. DA da i PE Quick Setup Guide Soundbar Home Theater Speaker DX SB114 FEATURES CONNECT THE SOUNDBAR Congratulations on your purchase of a Dynex Soundbar Home Theater Speaker System DVD Blu ray player gaming console etc Package contents AUDIO QUALITY JACK TYPE on source device Soundbar i PICK ONE Remote control AC adapter Digital connections BEST n l 1 Connect one end of the digital optical cable not included to your soundbar Connect the other end into the Digital SP Optical Output port on your audio source device A S lt 2 Change the device s audio output to PCM format RCA audio cable Ae RN typically found in Audio Settings Refer to the documentation that came with your audio source device e g TV projector DVD Blu ray player etc for more information Wall mounting template 3 After connecting power see USING YOUR SOUNDBAR on the next page Before using your new product please read these instructions to prevent any damage OR AUX IN connections GOOD Description Description 1 Connect the right angled end of the 3 5mm audio cable to Standby indicator Lights when the soundbar is in standby mode RCA IN R and L jacks If your TV or other audio source device has RCA OUT jacks your soundbar Plug the other end into the Audio Output connect the RCA cables to your source device and these jacks port or headphone jack on your audio source device C Powe
5. dbar or remote control The power indicator turns green 2 Turn on the audio source device connected to your soundbar and begin playback 3 Press the button on the soundbar or remote control repeatedly to cycle through the sound sources until you hear sound from your soundbar NOTE If you use the OPTICAL IN connection change the source device s audio source to PCM format Refer to the documentation you received with the audio source device such as your TV for additional information 4 Adjust the volume on your soundbar or the audio source device to a comfortable level WARNING Continuous use of high volume sound may permanently damage your hearing 5 Press the C Power button again to turn off your soundbar The standby indicator lights red TROUBLESHOOTING Check this list for a possible troubleshooting solution before calling for service 800 305 2204 Also check the online FAQs at dynexproducts com Problem Possible Solutions e Make sure that the AC adapter is securely plugged into the power outlet and the soundbar The power does not come on The remote control e Remove any obstacles in the path between the remote control and the soundbar IR sensor does not work Replace the battery e Point the remote control at the remote control sensor on the soundbar e Move closer to the soundbar The remote control reach is approximately 23 ft No sound or very e Make sure that the volume level of the soundba
6. e limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC warning Changes or modifications not expressly approved by the party responsible for compliance with the FCC Rules could void the user s authority to operate this equipment CANADIAN NOTICE CAN ICES 3 B NMB 3 B Standard Television Receiving Apparatus Appareil de r ception t l vision ordinaire Canada BETS 7 NTMR 7 ONE YEAR LIMITED WARRANTY Visit www dynexproducts com for details CONTACT DYNEX For customer service call 800 30
7. inal source device e Use a different connection method e g try Optical instead of AUX between the soundbar and the source device to make sure the jacks on both devices are still working can hear sound from Turn off or mute the internal speakers of your source device Refer to the device manual for instructions my TV and my soundbar My TV remote does not control the volume of my soundbar Controlling your soundbar with your TV remote is a feature of your TV See the documentation that came with your TV SPECIFICATIONS Designs and specifications are subject to change without notice Dimensions approx 31 5 x 3 5 X 2 7 in 800 x 89 x 70 mm V 20 W per channel at 10 THD Frequency response 150 Hz 15 kHz IMPORTANT SAFETY INSTRUCTIONS Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the p
8. ly operable 18 Batteries should not be exposed to excessive heat such as sunshine fire or the like WARNING Danger of explosion if battery is incorrectly replaced Replace only with the same or equivalent type Placement e The soundbar cabinet is made out of plastic and is therefore sensitive to extreme temperatures and humidity do not put it in locations subject to direct sunlight or in humid places such as near an air conditioner humidifier bathroom or kitchen Do not put water or other liquids close to the soundbar If liquid is spilled over the soundbar it may be damaged e The soundbar should be placed on a sturdy flat surface that is free from vibration or mounted on a wall Do not put the soundbar on an uneven or unstable surface where it may fall and cause damage Using close to a TV or computer Some older TVs and computer monitors are magnetically sensitive devices and as such are likely to suffer discoloration or picture distortion when conventional speakers are placed nearby If discoloration problems persist try moving the soundbar away from your TV or monitor LEGAL NOTICES FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with th
9. r button Press to turn on the soundbar The indicator lights green and indicator Press again to return the soundbar to standby mode AUX IN jack If your TV or other audio source device has an AUX OUT or 2 REF CONA POWE See URIS MOURN ONAR Gtr headphone jack connect the 3 5 mm audio cable to your the next page Input button Press repeatedly to cycle through the sound source options source device and this jack RCA gt AUX IN gt OPTICAL IN OPTICAL IN jack If your TV or other audio source device has an Optical OUT DSP Digital Signal Press repeatedly to cycle through the DSP sound modes jack connect a digital optical cable not included to your Processor button and e Standard Lets you enjoy normal sound source device and this jack _OR indicator e Theater Best for enjoying movies Bass frequencies are enhanced C Power button e News Select for clear voice reproduction RCA Audio connections GOOD The corresponding indicator lights to indicate the sound J INPUT button Press repeatedly to cycle through the sound source options 1 Foran RCA audio connection connect the right angled de selected sees ee connectors to your soundbar Connect the other end of the DSP buttons Press repeatedly to cycle through the DSP sound modes RCA cables into the Audio Output ports on your audio Standard gt Theater gt News The corresponding indicator on source device the soundbar top panel lights to indicate the sound mode selected
10. r or your source device is set to an adequate level low level sound is e Make sure that the volume is not muted Press the mute button on the remote control ha the e Make sure the correct audio source is selected Press the button repeatedly to switch to the correct audio source soundbar e Make sure that the sound mode is suitable for the audio source Press the DSP button to select a proper sound mode e Make sure the power is on and all connections are secure e Make sure the audio cable is connected to the Audio Output not the Audio Input on your source device e If you are connected to an MP3 player make sure the volume is turned up on the MP3 player Note The sound modes are memorized for each input unless you disconnect the AC adapter from the wall outlet Your soundbar is not working properly e Unplug the AC adapter from the wall outlet and then try plugging it in again after 30 seconds The sound is breaking Make sure all connections are secure and cables are not broken or damaged up or buzzing e If you are using the OPTICAL IN connection make sure the source device s audio source is set to PCM format Refer to the documentation your received with the audio source device e g TV projector DVD Blu ray player etc for additional information e Connect to a different source device e g TV projector DVD Blu ray player to see if the buzzing still occurs If it does not this may be an issue with the orig
11. rovided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 To reduce the risk of fire or electric shock do not expose this device to rain moisture dripping or splashing and no objects filled with liquids such as vases shall be placed on it 16 An apparatus with a three prong grounding type plug is a Class apparatus which needs to be grounded to prevent possible electric shock Make sure that you connect any Class device to a grounding type three prong outlet 17 The wall plug is the disconnecting device The plug must remain readi
12. wing listening position For best sound quality choose a location where sound waves are not blocked by furniture or other obstacles 2 Position the wall mount template where you want to mount it and make sure it is level A Tape it to the wall B then use a pencil to mark the screw hole locations C Remove the wall mount template e O O bE Wall 3 Install wall anchors not included into the marked locations using the instructions that came with your anchors NOTES e If you have drilled into a stud wall anchors are not required A CAUTION Use wall anchors designed for your wall type 4 Secure two screws not included into the wall or wall anchors if necessary The screws must protrude from the wall by about 1 2 12 7 mm Use a 10 wood screw or similar 1 1 2 in length 16 in 406 mm WARNING Improper installation can result in serious injury or damage to your soundbar If necessary seek the assistance of a professional USING YOUR SOUNDBAR Using the remote control 1 Remove the plastic tab from the battery compartment before using the remote control for the first time 2 Point the remote control directly at the IR sensor on the front of the soundbar You must be within approximately 23 ft 7 m of the soundbar IR sensor e See the instructions that came with your wall anchors to determine the drill bit size Listening to your soundbar 1 Press the Power button to turn on your soun
Download Pdf Manuals
Related Search