Dukane 8925H-RJ Projector User Manual
Contents
1. The information the CD ROM is subject to change without notice Please check our website where you may find the latest information for this projector 8318 No responsibility is taken for any obstacle and defect to hardware and software of your computer as a result of the use of the CD ROM All or Any part of the information in the CD ROM must not be copied reproduced or republished without notice to our company Item Specification Product name Liquid crystal projector Liquid Crystal Panel 786 432 pixels 1024 horizontal x 768 vertical 1 024 000 pixels 1280 horizontal x 800 vertical Lamp 210 W UHP Speaker 16 W mono 8 W x 2 Power supply Rated current 100 120 V 3 4 A 220 240 V 1 8 Power consumption AC 100 120 V 330 W AC 220 240 V 310 W U 5 35 C Operating range 317 W x 98 H x 288 D mm Size Not including protruding parts Refer to figure F 5 at the back of this manual Weight mass approx 3 5 kg COMPUTER IN1 D sub 15 pin mini jack x1 COMPUTER IN2 D sub 15 pin mini jack x1 HDMI connector x1 MONOTOR OUT D sub 15 pin mini jack x1 Y Cb Pb Cr Pr COMPONENT RCA jack x3 Mini DIN 4 pin jack x1 RCA jack x1 AUDIO IN1 3 5 mm stereo mini jack x1 AUDIO IN2 3 5 mm stereo mini jack x1 AUDIO IN3 R L RCA jack x2 AUDIO OUT R L RCA jack x2 USB TYPEA USB type A connector x1 USB TYPE B USB type B connector x1 CONTROL D sub 9 pin plug x1 RJ45 jack2. 1 2 49 46 9 Projection gt c i 0 distance cm linch cm linch m m m jinch m linch 0 91 35 11 4 0 0 6 0 0 LO oO lt lt 1 1 gt X 16 3 40 a 07 inch 40 09 05 Pape is s al al 30 0 61 0 4 ze O lt gt lt gt lt gt N 5 WUSB HDMI TYPEA DC5V 0 5A S VIDEO CONTROL Computer External device RS 232C RS 232C wireless adapter optional i 9 USB 2 6 OOO 00 gt device AUDIO S VIDEO INS OUT 20 VCR DVD Blu ray Disc player Monitor COMPONENT Speakers with an amplifier AUDIO OUT Microphone COMPUTER IN2 z gt oa Q 21 22
3. pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help ENGLISH B INSTRUCTIONS TO USERS This equipment complies with the requirements of FCC Federal Communication Commission equipment provided that the following conditions are met Some cables have to be used with the core set Use the accessory cable or a designated type cable for the connection For cables that have a core only at one end connect the core to the projector CAUTION Changes or modifications not expressly approved by the party responsible for compliance could vo
4. 181 154 n 2 E 1 1 C E e Screen height Projection distance 2 0 9 osfr 2 3 11 06 15 6119 73 64 25 2 4 13 OT 191422 2 4 15 MEERE 520 2 0 7 0 4 0 9 35 5 1 8 16 5 110 109 8 14 2 6 103 3 1 123 123 49 14 1 2 2 0 9 17 67 20 82 32 9 4 11 20 79 24 o s 38 11 oj os 14 56 17 67 69 27 8 6 15 18 9 3 3 191 5 8 227 193 76 6 2 2 T 2 1 54 65 T 5 13 16 137 165 3 5 4 2 5 9 11 13 2 9 3 5 1 5 1 8 2 0 95 ol os os t1 44 t3 so 58 22 6 30 0 6 0 5 0 8 32 inch m m m finch m inch cm inch cm inch m m m inch inch 200 4 1 3 0 234 7 1 278 274 108 30 12 4 4 256 7 7 304 257 101 250 5 1 3 8 7 5 294 8 9 349 343 135 38 15 5 5 321 9 7 381 322 127 10 300 6 1 4 6 9 0 354 10 7 420 411 162 46 18 6 6 37 9 8 386 11 6 458 386 152 1 150 3 0 2 3 44 175 5 3 208 206 81 23 100 120 2 4 1280x800 10 4 Projection mn 8927HW RJ 3 Screen size m inch m finch cm inch cm linch 1 0 40 8 67 Oil aM N ololo T lt 1 18
5. Apple Inc e Pentium is a registered trademark of Intel Corp Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated Microsoft Internet Explorer Windows Windows NT and Windows Vista are registered trademarks of Microsoft Corporation in the U S and or other countries e PowerPC is a registered trademark of International Business Machines Corporation HDMI the HDMI logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries Blu ray Disc is a trademark All other trademarks are the properties of their respective owners End User License Agreement for the Projector Software e Software in the projector consists of the plural number of independent software modules and there exist our copyright or and third party copyrights for each of such software modules Be sure to read End User License Agreement for the Projector Software which is separated document in the CD Ke N otc N C HD O 7 L oog cap Oo 2 0 Got e 5 x EO E 9 9 4 1024 x 768 10 16 Projection 9 Screen height distance b Screen size 1 1 1 ret N ely T 1 cm 15 42 39 3 2 3 9 8 2 126 T 129 152
6. In a couple of seconds after the power supply connection the POWER indicator will light up in steady orange Please remember that when the DIRECT POWER Power ON function activated the connection of the power cord supply make the projector turn on AWARNING gt Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and or electrical shock Do not touch the power cord with a wet hand Only use the power cord that came with the projector If it is damaged consult your dealer to get a new one Never modify the power cord Only plug the power cord into an outlet whose voltage is matched to the power cord The power outlet should be close to the projector and easily accessible Remove the power cord for complete separation Do not distribute the power supply to multiple devices Doing so may overload the outlet and connectors loosen the connection or result in fire electric shock or other accidents Connect the ground terminal for the AC inlet of this unit to the ground terminal of the building using an appropriate power cord bundled NOTICE This product is also designed for IT power systems with a phase to phase voltage of 220 to 240 V 8 Turning on the power 1 Make sure that the power cord is firmly and correctly connected to the projector and the outlet 2 Make sure that the POWER indicator is STANDBY ON button POWER indicator steady orange
7. ensure the proper use ll System requirements The system for using the CD ROM requires the following Windows OS Microsoft Windows 98 Windows 98SE Windows 4 0 Windows Me Windows 2000 Windows XP or later CPU Pentium processor 133MHz Memory 32MB or more Macintosh OS Mac OS 10 2 or later CPU PowerPC Memory 32MB or more CD ROM drive 4x CD ROM drive Display 256 color 640x480 dots resolution Applications Microsoft Internet Explorer 4 0 and Adobe Acrobat Reader 4 0 or later How to use the CD 1 Insert CD into computer s CD ROM drive Windows In a while Web browser automatically starts Start up window comes up Macintosh 1 Double click on the Projectors icon appeared on the desktop screen 2 When main html file is clicked Web browser will start and Initial window will appear 2 Click the model name of your projector first and then click language you want from the displayed list The User s manual detailed will open ACAUTION Only use the CD ROM in a computer CD drive The CD ROM is designed for computer use only NEVER INSERT THE CD ROM INTO A NON COMPUTER CD PLAYER Inserting the CD ROM into an incompatible CD drive may produce a loud noise which in turn MAY RESULT IN EAR AND SPEAKER DAMAGE After using CD ROM please put it into CD case and keep it Please keep the CD neither in direct sunlight nor in a high temperature and high humidity environment NOTE
8. high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition if the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury and dust containing fine particles of glass to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put itin a trash Dispose of it in accordance with environmental laws For lamp recycling go to www lamprecycle org in the US For product disposal consult your local government agency www eiae org in the US or www epsc ca in Canada For more information ask your dealer If the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass Z could damage the projector s internals or cause injury during handling so please do not try to clean the projector or replace the lamp yourself Disconnect the lamp should break it will make a loud bang when it does the plug ventilate the room well and make sure not to inhale the gas or fine fromthe particles that come out from the projector s vent holes and not to get ue them into your eyes or mouth Befo
9. same side as it 1 Holding the projector push the elevator buttons to Lax To loose an D Release the elevator buttons in order to lock the elevator feet After making sure that the elevator feet are locked put the projector down gently To finely If necessary the elevator feet can be manually adjust twist twisted to make more precise adjustments Hold the tne foot projector when twisting the feet oe oc a ANCAUTION Do not handle the elevator buttons without holding the projector since the projector may drop down Do not tilt the projector other than elevating its front within 14 degrees using the adjuster feet A tilt of the projector exceeding the restriction could cause malfunction or shortening the lifetime of consumables or the projector itself 10 Displaying the picture 1 2 Activate your signal source Turn the signal source on and make it send the signal to the projector Use the VOLUME VOLUME buttons to adjust the volume To have the projector silent press the MUTE button on the remote control Press the INPUT button on the projector Each time you press the button the projector switches its input port in turn You can also use the remote control to select an input signal Press the VIDEO button for selecting an input signal from the HDMI COMPONENT Y Cb Pb Cr Pr S VIDEO or VIDEO port or the COMPUTER button for selecting an input signal from the COMPUTER IN1 COMPU
10. TER IN2 LAN USB or USB TYPE B port Press the ASPECT button on the remote control Each time you press the button the projector switches the mode for aspect ratio in turn Use the ZOOM ring to adjust the screen size Use the FOCUS ring to focus the picture VOLUME button VOLUME button MUTE button INPUT button VIDEO button COMPUTER button ASPECT button ZOOM ring FOCUS ring ACAUTION If you wish to have a blank screen while the projector s lamp is on use the BLANK function see User s Manual Operating Guide Taking any other action may cause the damage on the projector NOTE The ASPECT button does not work when no proper signal is inputted For the details of how to adjust the picture please see User s Manual Operating Guide ENGLISH W Turning off the power 1 Press the STANDBY ON button on the STANDBYION button projector or the remote control POWER indicator The message Power off will appear on the screen for about 5 seconds 2 Press the STANDBY ON button again while the message appears The projector lamp will go off and the POWER indicator will begin blinking in orange Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete 3 Attach the lens cover after the POWER indicator turns in steady orange Do not turn the projector on for about 10 minutes or
11. THE ALL NEW DUKANE Education Presentation Inspiration Data Video Projector Concise User s Manual MODELS 8925H RJ 8926H RJ 8956H RJ 8927HW RJ Information in this Guide may change due to product improvements To obtain the latest manuals literature and software please visit the Dukane web site at www dukane com av and look at the specific model SUPPORT or DOWNLOADS section DUKANE CORP AV SERVICE DEPT 2900 Dukane Drive St Charles IL 60174 800 676 2487 630 762 4032 Fax 630 584 5156 avservice dukane com WA GU kan 403 8925H RJ PLUS CONCISE 00 Projector DUKANE 8925H RJ 8926H RJ 8956H RJ 8927HW RJ User s Manual concise Thank you for purchasing this projector Please read through this manual before using this product in order to use safely and utilize well the product AWARNING P Before using this product be sure to read all manuals for this product After reading them store them in a safe place for future reference gt Heed all the warnings and cautions in the manuals or on the product gt Follow all the instructions the manuals or on the product NOTE this manual unless any comments are accompanied the manuals means all the documents provided with this product and the product means this projector and all the accessories came with the projector Contents First of all 2 Entries and graphical symbols explanation 2 Important s
12. Then remove the lens D STANDBY ON INPUT cover pe n 9 f EN AAN O LAMP ig 3 Press the STANDBY ON button on the SS N Power projector or the remote control The projection lamp will light up and the POWER indicator will begin blinking in green When the power is completely on the indicator will stop blinking and light in steady green AWARNING strong light is emitted when the projector s power is on Do not look into the lens of the projector or look inside of the projector through any of the projector s openings NOTE Please power on the projector prior to the connected devices The projector has the DIRECT POWER ON function which can make the projector automatically turn on For more information please see User s Manual Operating Guide Adjusting the projector s elevator When the place to put the projector is slightly uneven to the left or right use the elevator feet to place the projector __ horizontally Using the feet can also tilt the projector in order to project at a suitable angle to the screen elevating the front side of the projector within 14 degrees This projector has 2 elevator feet and 2 elevator buttons An elevator foot is adjustable while pushing the elevator button on the same side as it loose the elevator feet alevator took uk Position the front side of the projector to the desired the elevator button L height on the
13. afety instruction 2 Regulatory notices 3 About Electro Magnetic Interference 3 About Waste Electrical and Electronic Equipment 4 Contents of package 4 Preparing for the remote control 5 6 Connecting with your devices 7 Fastening the adapter cover 8 Connecting power supply 8 Turning on the 9 Adjusting the projector s elevator 10 Displaying the picture 11 Turning off the power 12 Replacing the lamp 13 Cleaning and replacing the air filter 15 Using the CD manual 16 Specifications sae soon an Stop neon erint 17 Troubleshooting Warranty and after service 18 Projection Tables 19 ENGLISH IH First of all Entries and graphical symbols explanation The following entries and graphical symbols are used for the manuals and the product as follows for safety purpose Please know their meanings beforehand and heed them AWARNING This entry warns of a risk of serious personal injury or even death ANCAUTION This entry warns of a risk of personal injury or physical damage NOTICE This entry notices of fear of causing trouble Important safety ins
14. ct Do not place the product on an unstable place such as the uneven surface or the leaned table Do not place the product unstably Place the projector so that it does not protrude from the surface where the projector is placed on Remove all the attachments including the power cord and cables from the projector when carrying the projector Do not look into the lens and the openings on the projector while the lamp is Do not approach the lamp cover and the exhaust vents while the projection lamp is on Also after the lamp goes out do not approach them for a while since too hot 2 Regulatory notices About Electro Magnetic Interference In CANADA This Class B digital apparatus complies with Canadian ICES 003 In the US and other places where the FCC regulations are applicable Declaration of Conformity Trade name HITACHI Model Number CP X2514WN CP X3014WN 8926H RJ CP X4014WN 8956H RJ CP WX3014WN 8927HW RJ Responsible Party Hitachi America Ltd Address 900 Hitachi way Chula Vista CA 91914 3556 U S A Telephone Number 1 800 225 1741 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device
15. d lamps this is a cause of breakage Cleaning and replacing the air filter Please check and clean the air filter periodically When the indicators or a message prompts you to clean the air filter comply with it as soon as possible The air filter has two kinds of filters inside Replace the filters when they are damaged or too soiled To prepare the new filters make contact with your dealer and tell the following type number Type number MU06481 Filter set When you replace the lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector Turn the projector off and unplug the power cord Allow the projector to sufficiently cool down 2 Use a vacuum cleaner on and around the filter cover Filter cover ENGLISH E While supporting the projector with one hand use your other hand to pull the filter cover forward in the direction of the arrow 4 Use a vacuum cleaner for the filter vent of the projector the outer side of the filter unit 5 Take the filters out while holding the filter cover Use a vacuum cleaner on both sides of the filters When vacuuming up the fine meshed filter hold it so it will not be sucked in If the filters are damaged or heavily soiled replace them with the new ones Put the filters back into the filter cover Put the coarse meshed filter into a filter cover first Then put the fine meshed filter on the coarse mesh
16. ed one turning its stitched side up 8 Put the filter unit back into the projector 9 Turn the projector on and reset the filter time using the FILTER TIME item in the EASY MENU Filter coarse meshed 1 Press the MENU button to display a menu Filter fine meshed 2 Point at the FILTER TIME using the V A button then ro cose Siehe press the button A dialog will appear Seo 3 Press the button to select OK on the dialog It performs resetting the filter time AWARNING P Before taking care of the air filter make sure the power cable is not plugged in then allow the projector to cool sufficiently gt Use only the air filter of the specified type Do not use the projector without the air filter or the filter cover It could result in a fire or malfunction to the projector gt Clean the air filter periodically If the air filter becomes clogged by dust or the like internal temperatures rise and could cause a fire a burn or malfunction to the projector NOTE Please reset the filter time only when you have cleaned or replaced the air filter for a suitable indication about the air filter The projector may display the message such as CHECK THE AIR FLOW or turn off the projector to prevent the internal heat level rising Using the CD manual The other manuals for this product are written into the included CD ROM titled User s Manual detailed Before using the CD ROM please read the following to
17. from the outlet Do not touch the USB wireless adapter while the projector is receiving AC power NOTE Do not turn on or off the projector while connected to a device operation unless that is directed in the manual of the device Some input ports are selectable in the use For details see User s Manual Operating Guide Be careful not to mistakenly connect a connector to a wrong port If an oversized USB storage device blocks the LAN port use a USB extension cable to connect the USB storage device f a loud feedback noise is produced from the speaker move the microphone away from the speaker This projector doesn t support plug in power for the microphone ENGLISH IH Fastening the adapter cover Use the supplied adapter cover to prevent the USB wireless adapter from coming off easily 1 Loosen the screw marked with triangle on the bottom left of the USB TYPE A port 2 Insert the tab of the cover into the hole at the upper right of the USB port in the direction of the arrow 3 Align the screw holes on the projector and the cover Then insert the screw removed from the projector into the hole and tighten the screw AWARNING P Keep small parts away from children and pets Take care not to put in the mouth Connecting power supply 1 Put the connector of the power cord into the AC IN AC inlet of the projector 2 Firmly plug the power cord s plug into the outlet
18. id the user s authority to operate the equipment Regulatory notices continued About Waste Electrical and Electronic Equipment Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste but use the return and collection systems available If the batteries or accumulators included with this equipment display the chemical symbol Hg Cd or Pb then it means that the battery has a heavy metal content of more than 0 000596 Mercury or more than 0 002 Cadmium or more than 0 00496 Lead The mark is in compliance with the Waste Electrical and Electronic Contents of package Your projector should come with the items shown below Check that all the items are included Require of your dealer immediately if any items are missing 1 Remote control with two AA batteries 2 Power cord 3 Computer cable 4 Adapter cover 5 Lens cover 6 User s manuals Book x1 CD x1 7 Security label 8 Application CD AWARNING Keep small parts away from children and pets Take care not to put in the mouth If swallowed consult a physician immediately for emergency treatment NOTE Keep the original packing materials for future reshipment Be sure to use the original packing materials when moving the projector Use special caution for the lens The projector may make a rattling sound whe
19. ls such as cooking or machine oil are used Do not place the projector in a place where it may get wet ACAUTION Place the projector in a cool place with sufficient ventilation Keep a space of 30 cm or more between a side of the projector and other objects such as walls Do not stop up block nor cover the projector s vent holes Do not place the projector at places that are exposed to magnetic fields doing so can cause the cooling fans inside the projector to malfunction gt Avoid placing the projector in smoky humid or dusty place Do not place the projector near humidifiers NOTICE Position the projector to prevent light from directly hitting the projector s remote sensor Do not place the product in a place where radio interference may be caused gt Check and correct the setting for FAN SPEED of SERVICE in the OPTION menu according to the usage environment For details see User s Manual Operating Guide Connecting with your devices Before connecting the projector to a device consult the manual of the device to confirm that the device is suitable for connecting with this projector and prepare the required accessories such as a cable in accord with the signal of the device Consult your dealer when the required accessory did not come with the product or the accessory is damaged After making sure that the projector and the devices are turned off perform the connection according to the following in
20. more after turning it off Also do not turn the projector off shortly after turning it on Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp STANDBY ON Power AWARNING b Do not touch around the lamp cover and the exhaust vents during use or just after use since it is too hot gt Remove the power cord for complete separation The power outlet should be close to the projector and easily accessible NOTE Please power off the projector after any connected devices are powered off This projector has the AUTO POWER OFF function that can make the projector turn off automatically For more information please see User s Manual Operating Guide 12 Replacing the lamp A lamp has finite product life Using the lamp for long periods of time could cause the pictures darker or the color tone poor Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp make contact with your dealer and tell the lamp type number Type number 456 8755J 1 Turn the projector off and unplug the power cord Allow the projector to cool for at least 45 minutes Lampcover 3 2 Prepare a new lamp If the projector is mounted on a ceiling or if the lamp has broken also ask the dealer to replace the lamp In case of replacement by yourself follo
21. n tilted moved or shaken since a flap to control the air flow inside of the projector has moved Be aware that this is not a failure or malfunction Preparing for the remote control Please insert the batteries into the remote control before using it If the remote control starts to malfunction try to replace the batteries If you will not use the remote control for long period remove the batteries from the remote control and store them in a safe place 1 Holding the hook part of the battery cover remove it 2 Align and insert the two AA batteries HITACHI MAXELL Part No LR6 or R6P according to their plus and minus terminals as indicated in the remote control 3 Replace the battery cover in the direction of the arrow and snap it back into place AWARNING P Always handle the batteries with and use them only as directed Improper use may result in battery explosion cracking or leakage which could result in fire injury and or pollution of the surrounding environment When replacing the batteries replace both of the batteries with new batteries of the same type Do not use a new battery with a used battery Be sure to use only the batteries specified Do not use batteries of different types at the same time Do not mix a new battery with used one Make sure the plus and minus terminals are correctly aligned when loading a battery Keep a battery away from children and pets Do not recharge short circ
22. re replacing the lamp turn the projector off and unplug the power cord then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp Never unscrew except the appointed marked by an arrow screws Do not open the lamp cover while the projector is suspended from a ceiling This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or injury Use only the lamp of the specified type Use of a lamp that does not meet the lamp specifications for this model could cause a fire damage or shorten the life of this product e f the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this happens consult your local dealer or a service representative Handle with care jolting or scratching could cause the lamp bulb to burst during use Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old use
23. structions Refer to figures F 1 to F 4 at the back of this manual For details see User s Manual Operating Guide Before connecting the projector to a network system be sure to read User s Manual Network Guide too AWARNING P Use only the appropriate accessories Otherwise it could cause a fire or damage the projector and devices Use only the accessories specified or recommended by the projector s manufacturer It may be regulated under some standard Neither disassemble nor modify the projector and the accessories Do not use the damaged accessory Be careful not to damage the accessories Route a cable so that it is neither stepped on nor pinched out ACAUTION For a cable with a core at only one end connect the end with the core to the projector That may be required by EMI regulations Before connecting the projector to a network system be sure to obtain the consent of the administrator of the network Do not connect the LAN port to any network that might have the excessive voltage gt The designated USB wireless adapter that is sold as an option is required to use the wireless network function of this projector Before removing the USB storage device from the port of the projector be sure to use the REMOVE USB function on the thumbnail screen to secure your data Before you insert or pull out the USB wireless adapter from the projector turn off the power of the projector and pull out the power cord s plug
24. truction The followings are important instructions for safely using the product Be sure to follow them always when handling the product The manufacturer assumes no responsibility for any damage caused by mishandling that is beyond normal usage defined in these manuals of this projector AWARNING Never use the product in or after an abnormality ex giving off smoke smelling strange took a liquid or an object inside broken etc If an abnormality should occur unplug the projector urgently gt Situate the product away from children and pets gt Keep small parts away from children and pets If swallowed consult physician immediately for emergency treatment Do not use the product when there is fear of a thunderbolt gt Unplug the projector from the power outlet if the projector is not used for the time being Do not open or remove any portion of the product unless the manuals direct it For internal maintenance leave it to your dealer or their service personnel gt Use only the accessories specified or recommended by the manufacturer Do not modify the projector or accessories Do not let any things or any liquids enter to the inside of the product Do not wet the product Do not place the projector where any oils such as cooking or machine oil are used Oil may harm the product resulting in malfunction or falling from the mounted position Do not apply a shock or pressure to this produ
25. uit solder or disassemble a battery Do not place a battery in a fire or water Keep batteries in a dark cool and dry place If you observe battery leakage wipe out the leakage and then replace a battery If the leakage adheres to your body or clothes rinse well with water immediately Obey the local laws on disposing the battery ENGLISH IH Arrangement Refer to tables T 1 and T 2 at the back of this manual as well as the following to determine the screen size and projection distance The values shown in the table are calculated for a full size screen X O Screen size Projector top 8 Projection distance from the projector s end b Screen height Projector bottom AWARNING Install the projector where you can access the power outlet easily gt Install the projector in a stable horizontal position Do not use any mounting accessories except the accessories specified by the manufacturer Read and keep the manuals of the accessories used For special installation such as ceiling mounting be sure to consult your dealer beforehand Specific mounting accessories and services may be required Do not put the projector on its side front or rear position Do not attach nor place anything on the projector unless otherwise specified in the manual gt Do not install the projector near thermally conductive or flammable things Do not place the projector where any oi
26. w the following procedure Loosen the screw marked by arrow of the lamp cover and then slide and lift the lamp cover to the side to remove it 4 Loosen the 3 screws marked by arrow of the lamp and slowly pick up the lamp by the handles Never loosen any other screws 5 Insert the new lamp and retighten firmly the 8 screws of the lamp that are loosened the previous process to lock it in place 6 While putting the interlocking parts of the lamp cover and the projector together slide the lamp cover back in place Then firmly fasten the screw of the lamp cover 7 Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu 1 Press the MENU button to display a menu 2 Point at the ADVANCED MENU in the menu using the V A button then press the button 3 Point at the OPTION in the left column of the menu using the V A button then press the button 4 Point at the LAMP TIME using the V A button then press the button A dialog will appear 5 Press the button to select OK on the dialog It performs resetting the lamp time ANCAUTION bp Do not touch any inner space of the projector while the lamp is taken out NOTE Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp 13 ENGLISH R Replacing the lamp continued HIGH VOLTAGE A HIGH TEMPERATURE HIGH PRESSURE AWARNING The projector uses a
27. x1 3 5 mm mono mini jack x1 Lamp Filter set MU06481 Laser remote control RC R008 USB wireless adapter USB WL 11N Optional parts For more information please consult your dealer 17 ENGLISH R Troubleshooting Warranty and after service If an abnormal operation such as smoke strange odor or excessive sound should occur stop using the projector immediately Otherwise if a problem occurs with the projector first refer to Troubleshooting of User s Manual Operating Guide and Network Guide and run through the suggested checks If this does not resolve the problem please consult your dealer or service company They will tell you what warranty condition is applied Please check the following web address where you may find the latest information for this projector Product information and Manuals Note The Dukane projector models 8925H RJ 8926H RJ 8927HW RJ 8956H RJ are produced by the Hitachi Co of Japan Similar models are sold worldwide and correspond to Hitachi model numbers CP X2514WN CP X3014WN CP WX3014WN CP X4014WN NOTE The information in this manual is subject to change without notice The manufacturer assumes no responsibility for any errors that may appear in this manual The reproduction transfer or copy of all or any part of this document is not permitted without express written consent Trademark acknowledgment e Macintosh and Mac OS are registered trademarks of
Download Pdf Manuals
Related Search