Dometic 3300 Indoor Furnishings User Manual
Contents
1. STEP 7 Insert floor flange into larger hole and secure to the floor with 12x3 4 inch long flat head wood or sheet metal screws fig 7 STEP 8 Route 1 2 inch 13mm PEX tubing through the smaller hole and install a PEX 1 2 inch MPT fitting fig 8 NOTE A water shut off valve should be installed in the water line to the toilet for maintenance requirements IMPORTANT If replacing an existing toilet that uses FOR MODEL 3400 TOILET a 2 bolt floor flange drill two 5 16 inch dia holes in WITH REMOTE SWITCH old floor flange that align with two additional holes OPERATION see page 7 in floor flange adapter Use two 10 or 12 x 1 1 2 inch wood screws and washers for these drilled holes for wall switch installation and two T bolts with flat washers and nuts to fasten instructions flange gasket and floor flange adapter to old floor flange Do not use old hardware or seal STEP 9 WITH THE ELECTRICAL POWER OFF route STEP 13 Temporarily set the toilet in place on the floor 14 gauge stranded copper wire from 12 VDC ground flange fig 14 and positive 12 VDC from the fuse panel through a 7 or 8 amp fuse or circuit breaker Leave at least 30 inches 305 mm of wire for connecting to toilet fig 9 STEP 10 Connect the holding tank to the bottom of the STEP 14 Mark the holes for the two toilet mounting discharge flange bolts fig 15 STEP 11 Slide the four T bolts into the slots of the floor2. RG COMMON s GRN L51 CLOSED p 14 GA TINNED eee 5 t STRANDED COPPER WIRE PUR 152 OPEN RECOMMENDED 6 0 0 BLU WATER VALVE 7 WATER S GONDUCTOR 18 GA CABLE WHT WATER VALVE VALVE RED RED _ 9 1 ve WHT WHT COMMON WHI p y eaten A BLK 3 BLK DA e peo RED RED FLUSH 2 tie 12 lt I oK BLK ADD WATER p BLK BE aS 8 CONDUCTOR 18 GA CABLE ROCKER SWITCH 3 CONDUCTOR 18 GA CABLE 18 HEAVY LINES REPRESENT 14 GA STRANDED COPPER WIRE ROCKER SWITCH BACK VIEW 1 ALL OTHER WIRE CAN BE 18 GA STRANDED COPPER WIRE 1 18 CUSTOMER SERVICE There is a strong worldwide network to assist in servicing and maintaining your sanitation system For the Authorized Service Center near you please call from 8 00 a m to 5 00 p m ET Monday through Friday You may also write us at Dometic Corp P O Box 38 Big Prairie Ohio 44611 Telephone 1 800 321 9886 U S A and Canada 330 496 3211 International U S A MASTER SANITATION DISTRIBUTORS U S A North Central IL IN KY MI OH Midwest Marine Supply 24300 Jefferson Ave St Clair Shores MI 48080 Tel 586 778 8950 800 860 1540 Fax 586 778 6108 E mail midwestmarine yahoo com U S A Northeast CT DE DC MA MD ME NH NJ NY PA RI VA VT WV Northeast Marine Sanitation 69 Florida Street Farmingdale NY 11735 Tel 631 752 7606 800 352 4323
3. imensions vary D 3 8 inch 13mm TOILET INSTALLATION INSTRUCTIONS System Requirements 2 GPM 10 6 Ipm or larger water pump e 1 2 inch 12 7 mm water line terminating 1 2 inch MPT fitting to connect to toilet water supply hose e 4 bolt floor closet flange SeaLand flanges available include 3 inch spigot socket MPT or 45 degree swivel socket 12 VDC through 7 or 8 amp fuse or circuit breaker Use 14 gauge stranded copper wire IMPORTANT If replacing an existing gravity discharge toilet make sure the center of the existing discharge flange is at least 11 1 4 inches from the back wall then proceed to Step 5 for proper positioning of water line and electrical wiring STEP 1 Carefully unpack the toilet bowl rear access lid and floor flange adapter CAUTION HANDLE THE VIT REOUS CHINA TOILET AND ACCESS LID WITH CARE SET THE LID IN AN AREA WHERE IT CANNOT BE BROKEN PLACE LID ON TOILET ONLY AFTER TOILET INSTALLATION IS COMPLETE STEP 2 Position the china bowl in the space intended Confirm that adequate clearance is available for using the flush handle and opening the seat and lid STEP 3 Mark the floor at the rear corners of the toilet bowl fig 1 Measure the distance between the two marks and divide by 2 to find the toilet centerline Mark the floor at the rear wall for the centerline STEP 4 Place a carpenter s square against the back wall and draw a center line on the floor at least 14 i
4. Procedure Corrective Action Check the WATER VALVE If the WATER VALVE status light comes the water valve filter status light while pushing the screen may be plugged with debris or the water valve or its related Flush switch on the control wiring is defective panel If the WATER VALVE status light remains off replace the control module If voltage is not present replace the control module SYMPTOM 5 Flush valve will not open when Mode Switch is in the Service position but opens during a normal flush cycle Corrective Action Replace control module 16 TROUBLESHOOTING cont d SYMPTOM 6 Water will not stay in bowl Condition Procedure Corrective Action Put Mode Switch in Service e Clean underside of flush valve ball seal of dirt and debris position Worn or damaged flush valve ball Remove toilet from floor and remove base assembly from toilet and and seal replace flush valve ball and seals SYMPTOM 7 Water will not shut off and overflows the toilet Procedure Corrective Action Check the WATER VALVE status If the light is on when not flushing the toilet or adding water replace light the control module If the light responds correctly go to next step Dirt or debris lodged in the water valve seal Remove the toilet from the floor disassamble and clean water valve e Replace water valve SYMPTOM 8 Water is leaking from under the toilet
5. Procedure Remove the toilet from the Water hoses and fittings water valve assembly floor and inspect the following e China toilet bowl with both water and electrical power applied Upper base seal Place a container under the base e Flush valve ball rotor shaft shaft assembly to catch any water during i e Base assembly the inspection procedure 17 WIRING DIAGRAMS 3300 SERIES with flush handle FUSE OR CIRCUIT BREAKER CONTROL MODULE BASE ASSEMBLY CABLE INPUT POWER SUPPLY 12 VDC 12 VDC 7 8 AMP VDC INPUT gt s 3 1 3 WL f_ COMMON VOCINPUT gt 4 D gt ORG COMMON 151 CLOSED 14 GA TINNED STRANDED COPPER WIRE PUR LS2 OPEN RECOMMENDED 6 gt BLU WATER VALVE a WHT WATER VALVE Q RED RED BLK i BLK Le 8 CONDUCTOR 18 GA CABLE FLUSH LEVER ASSEMBLY CABLE WHT COMMON e gt RED FLUSH en O Prone BLK ADD WATER in NOTES HEAVY LINES REPRESENT 14 GA STRANDED COPPER WIRE ALL OTHER WIRE CAN BE 18 GA STRANDED COPPER WIRE 3400 SERIES with remote flush switch FUSE OR CIRCUIT BREAKER CONTROL MODULE BASE ASSEMBLY CABLE INPUT POWER SUPPLY 12 VDC 12 VDC 7 8 AMP VDC INPUT gt gt _ _ 9 5 __ VDC INPUT 7
6. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Flush Cycle In Seconds Flush Time Add Water Time PROPER CLEANING AND MAINTENANCE The Concerto toilet should be cleaned regularly for maximum sanitation and operational efficiency You can clean it just as you would a household toilet Do not use caustic chemicals such as drain opening types as they will damage the seals BOWL CLEANING For stubborn stains use SeaLand Bowl and Seal Cleaner Fig A It s manufactured especially for use with SeaLand toilets In certain locations where water is hard a build up of lime may dull the toilet bowl finish Restore the shine with this cleaner If you cannot find our brand in your area contact SeaLand Product Customer Service for your nearest dealer If it is not available you can also use Bar Keepers Friend cleanser It is not necessary to vigorously scrub with either product Please follow label instructions SEAL CLEANING After an extended time mineral deposits from hard water can build up under the edge of the rubber bowl seal resulting in a slow leakdown of water from the bowl To prevent this mineral build up periodically clean under the bowl seal with SeaLand Bowl and Seal Cleaner Fig 1 Put Mode switch in SERVICE position Flush ball will open automatically 2 Apply cleanser onto the seal cleaning tool supplied with new toilet and scrub under seal Make sure to push bristles between bottom of seal and t
7. Fax 631 752 7615 888 283 7606 E mail northeast northeastsanitation com U S A Northwest AK ID MT OR WA WY Marine Sanitation Inc 1900 Northlake Way Suite 121 Seattle WA 98103 Tel 206 633 1110 800 624 9111 Fax 206 633 0317 E mail marinesan mindspring com U S A South Central AR KS LA MO MS NM OK TX AER Supply P O Box 349 2301 Nasa Road 1 Seabrook TX 77586 281 474 3276 800 767 7606 Fax 281 474 2714 E mail sales aersupply com product line You may also contact or have your local dealer contact the Parts Distributor nearest you for quick response to your replacement parts needs They carry a complete inventory for the SeaLand Fax 330 496 3097 U S A and Canada 330 496 3220 International U S A Southeast AL FL GA NC PR SC TN VI Environmental Marine 111 S W 23rd Street Suite A Fort Lauderdale FL 33315 Tel 954 522 2626 800 522 2656 Fax 954 522 5152 E mail info environmentalmarine com U S A Southwest AZ CO NV UT CA south Ardemco Marine Specialties 778 West 17th Street Costa Mesa CA 92627 Tel 949 722 7672 800 253 0115 Fax 949 642 9582 E mail info ardemco com U S A Upper Midwest IA MN NE ND SD WI PowerHouse Marine 518 Logan La Crosse WI 54603 Tel 608 784 9580 888 752 4539 Fax 608 784 8422 E mail dave powerhousemarine com U S A Northern California Fox Marine 2250 Zanker Road Unit D San Jose CA
8. Limited Warranties 20 WARNING ELECTRICAL SYSTEM Turn off electrical power before servicing WARNING MOTOR STARTS AUTOMATICALLY Turn off electrical power before servicing Read and understand the complete contents of this manual before operating or servicing the toilet Failure to follow these precautions may result in damage to the toilet TOILET MODEL IDENTIFICATION The model identification label is located on the inside wall of the toilet under the access cover It will show the DOMETIC CORPORATION model number and serial number P O BOX 38 13128 STATE RT 226 800 321 9886 BIG PRAIRIE OH 44611 USA MODEL NO 0 00 SERIAL NUMBER 000000 ORDERING PARTS Dometic is ready to assist you in the event service is required Before calling please have the following information available Your cooperation in having this information ready is appreciated and allows us to better meet your needs Please refer to the Parts Distributor list in the Customer Service section 1 Toilet Model Number 2 Serial Number 3 Part Number Description and Quantity see Parts List Concerto SeaLand and Flush and Forget are registered trademarks of Dometic Corporation CONCERTO TOILET DIMENSIONS 14 3 4 inch 875mm 23 inch 584mm 33 1 2 inch 851mm Overall height 4 seat lid up 19 inch 483mm 17 1 4 inch 438mm Seat height 11 1 4 inch 286mm Back wall to
9. flange Install the flange gasket over the T bolts fig 10 STEP 15 Pick up toilet and set aside Drill 3 16 inch pilot holes in the floor fig 16 STEP 12 Install floor flange adapter with words THIS SIDE UP facing up Tighten adapter to floor flange using four flat washers and hex nuts Tighten in criss cross pattern fig 11 STEP 16 With toilet close to floor flange connect flex ible water supply hose to the water line fitting fig 17 STEP 17 Insert the positive 12 VDC wire into position 1 of the green terminal block and tighten the screw securely Insert the negative 12 VDC wire into position 2 of the green terminal block and tighten the screw securely fig 18 STEP 18 REMOVE RED CAP FROM MIDDLE OF FLANGE ADAPTER BEFORE FINAL TOILET INSTALLATION IMPORTANT DO NOT ATTEMPT TO SLIDE THE TOILET OVER THE FLANGE ADAPTER THE TOILET MUST BE SET DOWN OVER THE ADAPT ER TO PREVENT POSSIBLE DAMAGE STEP 19 Set the toilet in place fig 19 and secure to floor with the 14x2 1 2 inch long lag bolts fig 20 Install decorative bolt caps by pushing them onto bolt heads fig 21 STEP 20 Place the rear access cover on the back of the toilet Press down firmly to seat the fastening strips STEP 21 Turn on electrical power and water to toilet Lift flush handle and fill toilet bowl with water Wait one hour then inspect the floor around and under the rear of the toilet for
10. across pins 9 and 10 flip the Mode Switch between the NORMAL and SERVICE positions If voltage is present for about two seconds in the SERVICE position the flush valve motor or related wiring is defective If voltage is not present replace the control module 15 TROUBLESHOOTING con d SYMPTOM 3 Flush valve will not close Condition Procedure Corrective Action Mode Switch is in SERVICE e Return switch to the Normal position position Foreign object prevents the flush e Reset the control circuit by putting the Mode Switch in the SERVICE valve from closing and the safety position temporarily then returning to the NORMAL position If the circuit locked flush valve in open flush valve did not close go to next step position Pull the control module out as far as the control cables will allow Disconnect either the orange or green wire from the Closed Limit Switch With DC voltmeter test leads across pins 9 and 10 flip the Mode Switch between the SERVICE and NORMAL positions If voltage is present for about two seconds in the NORMAL position the flush valve motor or related wiring is defective If voltage is not present replace the control module Check the voltage output to the flush valve motor at pins 9 and 10 on the control module as follows e e SYMPTOM 4 Water will not enter toilet bowl during a flush and when the flush handle is raised or the flush switch is pushed to Add Water
11. leaks or dampness If no leaks are present toilet is ready for operation MODEL 3400 REMOTE FLUSH SWITCH INSTALLATION 3400 series toilets feature a remote flush switch to control the Flush and Add Water functions Follow the instructions below for switch installation STEP 1 Select a location for the switch 8 feet of cable 2 4 m is provided You may need to supply more wire depending on how far you locate the switch from the toilet STEP 2 Cut an opening 1 1 4 wide x 1 5 8 high see Ge pny hin diagram at right Cover outline j STEP 3 If installing the switch in a shallow wall you outing may need to use the spacer between the wall and the switch assembly cover to allow space for the wire con nectors If so route the cable through the spacer before proceeding to the next step STEP 4 Route the 3 conductor cable through wall cut out and on to toilet Cable can be routed with water 41 mm supply line and power wires see page 5 Step 9 Leave a minimum of 30 inches 76m of cable to allow easy wiring at toilet STEP 5 Fasten the switch assembly to the wall with the 6x1 screws included making sure to install with the label THIS SIDE on top Otherwise the Flush and Add Water functions will be reversed L 1 1 4 inch 32 STEP 6 Snap cover onto switch assembly to complete s
12. neces handle down Water will l sary raise flush handle flow into bowl for two sec until desired water level onds then flush ball will is reached Water flow open Toilet will not flush will stop automatically again until water refill cycle after a pre programmed is complete period of time gt Do not dispose of san itary napkins or other non dissolving items in toilet such as facial tissue or paper towels These 1 To add water to bowl press top items can cause plugging 2 To flush press of the system bottom part of switch TOILET CONTROLS ACCESS COVER ADD WATER REMOTE FLUSH SWITCH TOBOWL 3400 models 1 i CONTROL L A SWITCH FLUSH HANDLE 3300 models OFF Normal Service J gt Manual j 1 Override j N FLUSH Figure 1 OPERATING INSTRUCTIONS 1 Adding More Water To Toilet Bowl Pull up the flush handle 3300 model or push Add Water switch 3400 model until the desired water level is attained To prevent overflowing the toilet a timer inside the control module limits the amount of water that can be added 2 Flushing The Toilet Push the flush handle down 3300 model or push Flush switch 3400 model for a moment then release it Holding the handle or switch down will not prolong the flush cycle nor start a new flush cycle The handle or switch must be all
13. 95131 Tel 408 451 9055 800 826 2873 E mail foxmarco pacbell net 19 SSS CANADA MASTER SANITATION DISTRIBUTORS Canada East Eastern Marine Systems Inc 12 A Leslie Street Toronto Ontario M4M 3H7 Tel 416 465 1668 888 764 1111 Fax 416 465 2098 E mail info eastmar com Canada West Western Marine Company 1494 Powell Street Vancouver BC V5L 5B5 Tel 604 253 7721 800 663 0600 Fax 604 253 2656 800 663 6790 E mail sales westernmarine com eee INTERNATIONAL SEALAND SANITATION SYSTEM DISTRIBUTORS Call 1 800 321 9886 email us at sealand dometicusa com or visit www dometicusa com for the distributor nearest you MANUFACTURER S THREE YEAR AND TEN YEAR LIMITED WARRANTIES Dometic Corporation warrants to the original purchaser only that this Concerto gravity discharge toilet if used for personal family or household like purposes is free from defects in material and workmanship for a period of three 3 years from the date of purchase Dometic also warrants to the original purchaser only that the vitreous china toilet bowl will not discolor stain scratch or craze for a period of ten 10 years if used for personal family or household like purposes and is regularly cleaned as described in the product s owner s manual If this Dometic product is placed in commercial or business use it will be warranted to the original purchaser only to be free of defects in material and wor
14. CONCERTO ELECTRIC FLUSH GRAVITY DISCHARGE TOILET OWNER S MANUAL 3300 Series 3400 Series with flush handle with remote flush switch A WARNING This manual must be read and under stood before installation adjustment service or maintenance is per formed Modification of this product aD Dometic r can result in property damage Dometic Corporation Sanitation Systems 13128 State Rt 226 PO Box 38 Big Prairie OH 44611 SeaLand Product Customer Service 1 800 321 9886 8 00 a m 5 00 p m ET TABLE OF CONTENTS Toilet Model Identification 2 Proper Cleaning and Maintenance 10 Ordering Parts 2 Manual Flush Operation 10 Concerto Toilet Dimensions 3 WINTENIZING 2 2 adored ddd eden es 11 Toilet Installation Instructions 3 6 Spare 11 Remote Flush Switch Installation 7 Deodorants and Special Tissue 11 Important Information Before Operation 8 Flush Mechanism Components 12 Electronic Flush and Forget Operation 8 Electrical Specifications 13 Toilet Controls 8 14 17 Operating Instructions 9 Wiring Diagrams 18 Automatic Flush Operation Timing Chart 9 Customer Service 19
15. ding incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state To obtain warranty service first contact your local dealer from whom you purchased this product Dometic Dometic Corporation Sanitation Systems 13128 State Rt 226 PO Box 38 Big Prairie OH 44611 SeaLand Product Customer Service 1 800 321 9886 8 00 a m 5 00 p m ET Registered Trademark of Dometic Corporation Bar Keepers Friend is a registered trademark of SerVaas Laboratories Dometic Corporation 600344954 10 04
16. ition Status Light Color Function 1 Valve Closed Green Flush valve Closed Limit Switch engaged 2 Valve Open Green Flush valve Open Limit Switch engaged 3 Flush Green Flush handle or wall switch in Flush position 4 Add Water Green Flush handle or wall switch in Add Water position 5 Water Valve Green Electric water valve energized 6 Status Green Status error codes 7 5V Green Input power ERROR CODES Status Light No of Flashes Pause Condition 6 1 5 SEC Mode Switch in SERVICE position 6 1 2 SEC VALVE OPEN Limit Switch problem 6 2 2 sec VALVE CLOSED Limit Switch problem CONTROL MODULE STATUS LIGHTS VALVE OPEN C D2 FLUSH Lep3 ADD WATER 1804 WATER VALVE C Leps STATUS D6 5V 1807 VALVE CLOSED Lep1 14 TROUBLESHOOTING ERROR CODE CORRECTIVE PROCEDURES Condition Corrective Action Mode Switch in SERVICE position Return Mode Switch to NORMAL position Valve Open Limit Switch problem With the flush valve fully open check the VALVE OPEN status light If the light is off then the Valve Open Limit Switch is out of alignment or defective or related wiring is defective Valve Closed Limit Switch problem With flush valve in the fully closed position check the VALVE CLOSED status light If the light is off then the Valve Closed Limit Switch is out of alignment or defective or related wiring is defective TOILET OPERATION SYMPTOM 1 Toilet will not flush and wate
17. kmanship for a period of ninety 90 days from the date of purchase Dometic reserves the right to replace or repair any part of this product that proves upon inspection by Dometic to be defective in material or workmanship All labor and transportation costs or charges incidental to warranty service are to be borne by the purchaser user EXCLUSIONS INNO EVENT SHALL DOMETIC BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR DAMAGES RESULTING FROM IMPROPER INSTALLATION OR FOR DAMAGES CAUSED BY NEGLECT ABUSE ALTERA TION OR USE OF UNAUTHORIZED COMPONENTS THIS INCLUDES FAILURES WHICH MAY RESULT FROM NOT FOLLOWING THE WINTERIZATION OR CLEANING PROCEDURES AS DESCRIBED IN THIS MANUAL ALL IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORANY PARTICULAR PURPOSE ARE LIMITED TOA PERIOD OF ONE 1 YEAR FROM DATE OF PURCHASE IMPLIED WARRANTIES No person is authorized to change add to or create any warranty or obligation other than that set forth herein Implied warranties including those of merchantability and fitness for a particular purpose are limited to one 1 year from the date of purchase for products used for personal family or household like purposes and ninety 90 days from the date of purchase for products placed in commercial or business use OTHER RIGHTS Some states do not allow limitations on the duration of an implied warranty and some states do not allow exclusions or limitations regar
18. locked rotor current amps 14 5 Maximum voltage 15 Minimum voltage 10 Input power wire size 14 ga All other wires size 18 ga Fuse size amps 8 13 TROUBLESHOOTING A volt ohmmeter VOM and the Toilet Wiring Diagram may be required for this section Caution Portions of this section will require that power be applied to the toilet Keep hands away from the flush ball motor drive arm and rotor shaft to prevent personal injury during testing and troubleshooting The control module uses a microprocessor to provide all the automatic and timing functions The module is under the access cover The control module has input and output status lights that can be used in troubleshooting the toilet The program in the microprocessor monitors the input and output signals during a normal flush cycle If the inputs or outputs do not follow the commands of the program then the microprocessor may go into a standby mode and flash an error code The microprocessor is reset by placing the Mode switch in the SERVICE position temporarily then returning the switch to the NORMAL position A safety circuit in the control module monitors flush ball operation If foreign objects or low voltage prevent the flush ball from closing this circuit prevents personal injury or damage to the flush valve motor If this condition occurs reset the control module by placing the Mode switch into the SERVICE position temporarily then returning it to the NORMAL pos
19. nches 356 mm long fig 2 Mark the centerline for the floor flange at 11 1 4 inches 286 mm from the wall fig 3 STEP 5a For through the floor water line and electrical wires mark another centerline 6 inches 152 mm from the back wall fig 4 STEP 5b For through the wall water line and electrical wires mark a centerline 8 inches 203 mm up from the floor centerline fig 5 STEP 6 Make a 4 3 4 inch 121 mm diameter hole for most floor flanges or a 5 1 8 inch 130 mm diameter hole for swivel joint floor flange at the centerline mark furthest from the wall Make a 1 inch 25 mm hole at the mark closer to the wall for the water line and electrical wires fig 6 IMPORTANT The prefered floor flange installation method is to mount the floor flange directly on the finished floor However if the bottom of floor flange and bottom of china toilet must be mounted at differ ent heights the floor flange must be mounted within 3 8 inch 10 mm of the bottom of the toilet see il lustrations in next column or leakage may result CHA TOILED Below Floor Installation BASE REAR SPACE BETWEEN BOTTOM OF CHINA BASE AND BOTTOM OF FLOOR FLANGE RIM SHOULD BE NO GREATER THAN 3 8 INCH 10 mm Above Floor Installation CHINA TOILET BASE REAR BETWEEN BOTTOM OF CHINA BASE AND BOTTOM OF FLOOR FLANGE RIM SHOULD BE NO GREATER THAN 3 8 INCH 10 mm FLOOR SUB FLOOR l l
20. op of flush ball surface to scrub all parts of seal that come into contact with flush ball 3 Wait 2 3 minutes 4 Pullup on flush handle or push Add Water switch to let water flow into bowl Use cleaning tool and water to rinse away cleanser and loosened deposits You can add water for up to 15 seconds in the SERVICE position 5 Put Mode switch in NORMAL position Water will flow for a few seconds then flush ball will close automatically Water will continue flowing into bowl making it ready for the next flush MANUAL FLUSH OPERATION In the event of an electrical failure the flush ball of the toilet can be manually opened to clear the bowl We recom mend using a long neck screwdriver or 7 16 in socket for the operation shown below NEVER PRY OPEN THE FLUSH BALL FROM INSIDE THE TOILET BOWL Damage to the flush ball and bowl seals may result 1 Remove access cover from top of china toilet Place Mode 3 Insert screwdriver or 7 16 in socket through access hole Switch in the Manual Override position This disconnects and onto hex head flush valve motor brake from electrical circuit Manual Override position 4 Turn screwdriver or socket counter clockwise This will open flush ball and allow bowl contents to clear After bowl is clear turn screwdriver or socket clockwise to return flush ball to original position 2 Locate hole on side of china toilet This allows access to the flush valve motor drive arm NOTES Wa
21. ormaldehyde versus Non Formaldehyde Dometic manufactures both types of deodorants Generally speak ing formaldehyde formulas control odor very effectively at all temperatures and with all degrees of water hardness SeaLand Environment Friendly brand which is formaldehyde free is similarly effective How Much Deodorant and How to Add It The deodorant is added directly into the toilet bowl then flushed into the holding tank Follow bottle or package instructions Conditions of extremely warm weather longer waste hold ing time and larger tank capacities may require more deodorant treatment Also to maintain optimum efficiency in odor control the waste holding tank should be cleaned thoroughly at least once or more each season depending on use Why Not Use Household Toilet Paper in Your ConcertoToilet Household tissues often contain adhesives which bond together the paper fibers from which the tissue is made The adhesives prevent the tissue from breaking apart and their use in ultra low flow systems can cause system clogging SeaLand tissue is especially designed for use in low water toilet systems Its rapid dissolving properties minimize the amount of residual paper in the holding tank and allow deodorizers to work more efficiently SeaLand versus Other Brands SeaLand constantly strives to provide our system owners with effective products that have minimal environmental impact and good value Many deodorant products do not measure up
22. owed to return to the neutral position before another flush can occur 3 Mode Switch The Mode switch is located on the right side of the control module It lets you switch between three function settings NORMAL Use this setting for flushing the toilet SERVICE Use this position for cleaning the toilet bowl and flush ball seal The flush ball will open automatically and re main open in this position Lifting up the flush handle or pushing the Add Water switch provides water to the bowl MANUAL OVERRIDE Use this position to flush the toilet manually in the event of power or battery failure This switch disconnects the electronic brake in the flush valve motor and allows manual flushing via the override access hole in the side of the vitreous china base Note The control module allows 15 seconds of water flow for cleaning If more water is required return the switch to the NORMAL position then back to the SERVICE position A safety circuit the control module monitors flush ball operation If foreign objects or low voltage prevent the flush ball from closing this circuit prevents personal injury or damage to the flush valve motor If this condi tion occurs reset the control module by placing the Mode switch into the SERVICE position temporarily then returning it to the NORMAL position AUTOMATIC FLUSH OPERATION TIMING CHART Flush and Forget Cycle Time Water Valve Water flow Flush Valve Opening Held Open Closing
23. r will not enter toilet bowl Condition Corrective Action 5V status light is off A Check toilet fuse or circuit breaker at DC distribution panel Check for loose or defective wiring between control module and DC distribution panel Check for reverse polarity of input power to control module If all of above check OK replace control module e e e Input power must be 10 volts or higher Check control module for error codes Put Mode Switch in SERVICE position If flush valve opens go to next step If the flush valve does not open go to Symptom 2 Put the Mode Switch in NORMAL position and push handle or switch l to Flush while observing FLUSH status light The FLUSH status 5V status light is on light must come on when the switch is pushed go off when the switch is released If the FLUSH status light did not follow com mands of switch then flush switch or related wiring is defective SYMPTOM 2 Flush valve will not open when the Mode Switch is in the SERVICE position or when the flush handle or switch is pushed to Flush while in the NORMAL position Procedure Corrective Action Check the voltage output Pull the control module out as far as the control cables will allow to the flush valve motor at Disconnect either the purple or yellow wire from the Open Limit pins 9 and 10 on the Switch control module as follows With DC voltmeter test leads
24. ter will not enter the toilet bowl during manual flush operation Place Mode Switch in the Normal position before return ing to automatic operation 10 WINTERIZING At the end of each traveling season the Concerto toilet system must be winterized for storage The following procedure should be used 1 Pump out waste holding tank 2 Thoroughly flush toilet system with fresh water 3 Drain freshwater tank 4 Add freshwater antifreeze to freshwater tank 5 Flush freshwater antifreeze and water mixture through toilet and into the waste holding tank Each installation is different so amounts may vary User discretion is required to assure adequate protection 6 Turn off electrical power SPARE PARTS It is recommended that the following spare parts be kept available at all times Flush Ball Seal Kit see parts list 1 Water Valve see parts list 1 Flush Ball see parts list 1 Vacuum Breaker Assembly see parts list 1 DEODORANTS AND SPECIAL TISSUE Your Concerto toilet requires the regular addition of a deodorant product to reduce malodors and to help break down holding tank contents Several factors should be considered in selecting a deodorant product Liquid or Dry Liquid products obviously work more quickly by readily going into solution Granulated powder formulations on the other hand have the advantage of requiring less storage space and are less likely to leak if the package is inadvertently damaged F
25. to our standards of performance and value lt SeaLand Granulated SeaLand Liquid Deodorant Deodorant SeaLand Six 2 07 Environment Rapid pouches Friendly Dissolving Part No 32 02 Papier da 379626002 Part No Four 400 sheet ee 379114032 tolls Part No SeaLand Liquid 379441204 Deodorant Two 8 oz bottles Part No 379224008 11 FLUSH MECHANISM COMPONENTS 3 Lift china toilet straight up from base and set it down just in front of floor flange Turn off water to toilet and disconnect flexible water line Dis connect power wires and or flush switch wires if necessary 1 To access base assembly components remove decorative screw caps and unscrew two bolts that hold china toilet to floor 2 Remove access cover from top of china and set it aside FLUSH HANDLE COMPONENTS CONTROL MODULE Mode 3300 series s _ Switch Flush Handle Switch Input for 7 Input for REMOTE FLUSH SWITCH Cable Base Assembly Cable 3400 series Water Valve Flush Ball BASE ASSEMBLY COMPONENTS under china toilet Flush Valve Motor Open Limit Switch Closed Limit Cable a Switch Flexible Water Supply Hose 12 Base Assembly TOILET SYSTEM ELECTRICAL SPECIFICATIONS 12VDC Maximum standby current amps 070 Maximum operating current amps 6 5 Flush motor
26. witch installation on wall STEP 7 WITH THE ELECTRICAL POWER OFF connect the red black and white wires from the switch to the red black and white wires connected to the 11 12 and 13 terminals on the control module See page 6 Step 17 for other wiring procedure REMOTE FLUSH SWITCH COMPONENTS TOP VIEW ah SPACER BACK VIEW FRONT VIEW COVER SWITCH ASSEMBLY IMPORTANT INFORMATION BEFORE OPERATION 1 Fill freshwater tank and add deodorant to holding tank through toilet bowl CONCERTO 2 Make sure all guests understand the operation of the toilet system 3300 models This flushing instruction label is located under the seat and is easily read when the ney seat is raised 3400 models Add Water and Flush are clearly marked on the remote switch 3 Shut off the toilet system before servicing and do not leave the vehicle with toilet system circuit breaker on gt A Never use drain openers alcohol solvents etc in the toilet 5 Ifthe toilet does not function properly refer to the Troubleshooting section of this manual and repair as neces sary If problem persists contact your local SeaLand product dealer or see the Customer Service section of this manual ELECTRONIC FLUSH AND FORGET OPERATION FLUSH HANDLE TOILET REMOTE FLUSH DO NOT FLUSH SWITCH TOILET FOREIGN OBJECTS 1 To add water to the toilet 2 To flush toilet press flush THROUGH TOILET before using if
Download Pdf Manuals
Related Search