Home

Dixon 44, 44, 44, 36, 36, 42, 42 Lawn Mower User Manual

1. 8009 147 Fuel pump air filter MAINTENANCE Tire Pressures All four tires should have a pressure of 15 psi 103 kPa 1 bar WARNING The machine must be standing absolutely still when the park brake is engaged Parking Brake Visually check that no damage is found on the lever linages or switch belonging to the parking brake Perform a stand still test and check that there is a braking action To adjust the parking brake contact the Dixon service workshop A WARNING Faulty adjustment can cause an accident V belts Deck belt Inspect every 50 hours of operation Check for severe cracking and large nicks NOTE The belt will show some small cracks in normal operation Belt tension is manually adjustable Turn bolt on deck eyebolt to adjustment tension NOTE Belt deflection or movement should be approximately 14 6mm when measured at midpoint between pulleys Periodically inspect both belt and idler systems 8011 564 Check tire pressure 8050 823 Tension Eyebolt 8050 824 Adjusting belt tension DIXON 4 1 MAINTENANCE Deck belt removal 1 2 3 Park on a level surface Apply parking brake Lower the deck into the lowest cutting position Remove bolts from belt shields and remove shields Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface Carefully roll the belt over the top of the cutter housing pull
2. IMPORTANT INFORMATION Fitting the wrong spark plug type can damage the engine Inadequately tightened spark plug can cause overheating and damage the engine Tightening the spark plug too hard can damage the threads in the cylinder head 0 028 0 031 in t 0 70 0 80 mm 8011 054 Measure the electrode gap 8050 822 Start conditions DIXON 37 MAINTENANCE Engine Cooling Air Intake Check that the engine s cooling air intake is free from leaves grass and dirt If the cooling air intake is clogged engine cooling deteriorates which can lead to engine damage Throttle Cable Check that the engine responds to throttle increases and that a good engine speed is attained at full throttle If doubts arise contact the service workshop If adjustments are necessary they can be made as follows for the lower cable 1 Loosen the clamping screw for the cable s outer casing and move the throttle to the full throttle position 2 Check that the throttle cable is mounted in the correct hole in the lower lever see illustration 3 Push the throttle cable s outer casing as far to the left as possible and tighten the clamping screw Choke Cable If the engine produces black smoke or is difficult to start this may be because the choke cable is incorrectly adjusted upper cable If doubts arise contact the service workshop If adjustments are necessary they can be made as follows 1 Loosen t
3. Sharpen Replace mower blades Clean the engine s cooling air intake 2 Clean the air cleaner s pre filter 2 foam Clean the air cleaner s filter cartridge 2 paper filter Check adjust the parking brake 0 0 e Inspect muffler Spark arrester Check the fuel pump s air filter 2 e 34 DIXON MAINTENANCE Daily Weekly At Maintenance interval least in hours once Maintenance Before After each 25 50 100 300 year Check adjust throttle cable Check the condition of belts belt pulleys e Change the engine oil e e Replace the engine oil filter e Clean replace the spark plugs e Replace the fuel filter e Replace the air filter paper filter 2 e Check the caster wheels every 200 hours e Replace the air cleaner s pre filter 2 foam e Check adjust the mower deck e e Check the engine valve clearance 3 4 4 Perform the 300 hour service 3 4 4 Lubricate according to Lubrication Schedule e e e e e Clean fins of oil cooler 4 4 1 First change after 5 8 hours When operating with a heavy load or at high ambient temperatures replace every 50 hours 2 In dusty conditions cleaning and replacement are required more often 3 Performed by authorized service workshop Described in this manual Not described in this manual WARNING Before performing any service or adjustment checkl
4. LUBRICATION Lubricating the Cables If possible grease both ends of the cables and move the controls to end stop positions when lubricating Refit the rubber covers on the cables after lubrication Cables with sheaths will bind if they are not lubricated regularly If a cable binds it can disrupt operation If a cable binds remove the cable and hang it vertically Lubricate it with light engine oil until the oil begins to escape from the bottom Tip Fill a small plastic bag with oil and tape it so that it seals against the sheath and allow the cable to hang vertically from the bag overnight If you do not succeed in lubricating the cable it must be replaced Following the Lubrication Schedule Front Wheel Mount Lubricate with a grease gun one zerk for each wheel mount until the grease is forced out Use only good quality bearing grease Grease from well known brand names petrochemical companies etc usually maintains a good quality Front Wheel Bearings Lubricate with a grease gun one zerk for each set of wheel bearings until the grease is forced out Use only good quality bearing grease Deck Spindle Lower the cutting deck completely If you use grease gun without rubber hose the foot plate must be removed Lubricate with a grease gun one zerk 2 3 strokes Use only good quality bearing grease IMPORTANT INFORMATION Use minimal lubrication and remove excess lubricant so that is does not come
5. BPR4ES 030 0 75 mm freemen 64 DIXON TECHNICAL DATA pz TR AA 968999611 avon fronerce sdf ema ETEA AAA DIXON 65 CONFORMITY CERTIFICATES USA Requirements Labels are placed on the engine and or in the engine compartment stating that the machine will fulfill the requirements This is also applicable to special requirements for any of the states California emission rules etc Do not remove any of these labels Certificates can also be supplied with the machine at delivery or written in the Engine manual Take care of them as they are valuable documents 66 DIXON SERVICE JOURNAL Action Date mtr reading stamp sign Delivery Service 1 BON N Q a 12 13 14 Charge the battery Adjust the tire pressure of all wheels to 15 PSI 1 bar Mount the steering controls in the normal position Connect the contact box to the cable for the seat s safety switch Check that the right amount of oil is in the engine Adjust the position of the steering controls Fill with fuel and open the fuel shut off valve Start the engine Check that there is drive to both wheels Check the mower deck adjustment Check The safety switch for the parking brake The safety switch for the mower deck The safety switch in the seat The safety switch in the steering controls Parking brake functionality Driving forward Driving backward Engaging the blades Chec
6. 1 Always turn off engine before engaging or disengaging the hydro release free wheel lever Never attempt to move the lever with the engine running 2 Lift the seat to access release levers Push the hydro release levers toward the rear of the machine and inward until notches lock in place on frame Release park brake 3 To engage the transmissions move the release levers outward so they return to normal position Push lever in and lock notch on frame 2 places Bypass linkages IMPORTANT INFORMATION Before pushing or towing tractor transmission must be unlocked and park brake released The tractor should never be pulled at more than 2 miles per hour 3 2 km h or for distances over mile 402 km Trailer the unit for distances over 4 mile 8050 165 8050 811 DIXON 19 CONTROLS Fuel Tank The machine has one fuel tank just behind the seat The tank capacity is 4 5 gallons 17 liters The engine will run on a minimum of 85 octane unleaded gasoline no oil mix Environmentally adapted alkylate gasoline can be used See also Technical Data concerning ethanol fuel Methanol fuel is not allowed When operating below 32 F 0 C use fresh clean winter grade gasoline to help insure good cold weather starting WARNING Gasoline is highly flammable Observe caution and fill the tank outdoors See Safety WARNING Fill to the bottom of the filler neck Do not overfill Wipe off any
7. For units with choke throttle combinations push the throttle control all of the way forward into the indicated slot Throttle Control The throttle control regulates the engine speed and thereby the rate of rotation of the blades assuming the blade switch is pulled out see Engaging the Mower Deck In order to increase or decrease the engine speed the control is moved Avoid idling the engine for long periods as there is a risk of fouling the spark plug USE FULL THROTTLE WHEN MOWING for best mower performance and battery charging FG Zs Ignition Switch 8050 816 AE X KA 2 z NZ 0 9 Choke control 8050 817 THROTTLE Choke and throttle control 8050 816 DIXON 21 CONTROLS Blade Switch In order to engage the mower deck pull the knob out the mower blades are disengaged when the knob is depressed Circuit Breaker The circuit breaker provides protection for the electrical system by 1 15 amp circuit breaker If the circuit breaker trips push the button to reset If the condition repeats consult a dealer for inspection and repair Parking Brake The parking brake is found on the operator s left Pull the lever upward to activate the brake and dow
8. e Never allow children to operate the machine e Use extra care when approaching blind corners shrubs trees or other objects that may block your view of a child 8011 517 8011 518 Keep children away from work area DIXON 11 SAFETY i WARNING The engine must not be started when the driver s floor plate or any protective plate for the mower deck s drive belt is removed Safe Handling of Gasoline To avoid personal injury or property damage use extreme care in handling gasoline Gasoline is extremely flammable and the vapors are explosive e Extinguish all cigarettes cigars pipes and other sources of ignition e Use only approved gasoline container e Never remove gas cap or add fuel with the engine running Allow engine to cool at least two 2 minutes before refueling e Never fuel the machine indoors e Never store the machine or fuel container where there is an open flame spark or pilot light such as on a water heater or other M appliance 8011 516 Before you begin refueling minimize the risk of Never fill the fuel tank indoors static electricity by touching a metal surface e Never fill containers inside a vehicle or on a truck or trailer bed with plastic liner Always place containers on the ground away from the A an WARNING vehicle when filling e Remove gas powered equipment from the The engine and the exhaust system truck or trailer and refuel it on the ground If become very hot
9. gt 20CD 71 ZTR SPEEDZTR 44 968999538 SPEEDZTR 44 968999547 SPEEDZTR 44 968999611 SPEEDZTR Operator Manual SPEEDZTR 36 968999539 SPEEDZTR 36 968999609 SPEEDZTR 42 968999689 SPEEDZTR 42 968999713 Please read the operator s manual carefully and make sure you understand the instructions before using the machine 2008 HTC All rights reserved Beatrice NE Printed in U S A TABLE OF CONTENTS INTRODUCTION minmeneennnanennnnnnan enne 4 Driving and Transport on Public Roads 4 TOWING di 22 100 eda kihk melee kaka va de klaad 4 Operating e cims seis sta kavas i EREN 4 Good SEVICE 5 4 141 katki vanad aatkt ka ledv kantaat kaak 5 SYMBOLS AND DECALS riccii 6 SAFET Yonen AEEA 8 General Operation 0 mnnnanan 8 Personal Safety Equipment 2 10 Slope Operation mnvmemenennennennana 10 Safe Handling of Gasoline 12 General Maintenance 06mmmmeenm 13 Transporto aeaiiai a iana eaii 15 Roll Over Protection System ROPS 16 GONTROLS 2m013eh nt kaa viga tktadetphadka deep aaa h kke v he 17 Motion Control Levers essiccare 18 Eaa E E E E E O 18 Seat Adjustment Lever seeren 19 Bypass Linkage msetnnnennmane 19 Fuel Tank iscsciesjeseeitesscentteas stennees deere erates 20 Ignition Swit
10. tae TI mga ee Ce Ra flame and smoking materials away from batteries Always wear eye protection when around batteries If your battery is too weak to start the engine it should er be recharged See Battery in the Maintenance mira rm ey Section lt IMPORTANT INFORMATION Your mower is eguipped with a 12 volt negative grounded system The other vehicle must also be a 12 volt negative grounded system Do not use your mower to start other vehicles 8011 642 Jumper cable connection If jumper cables are used for emergency starting follow this procedure Jumper Cables 1 Connect each end of the RED cable to the POSITIVE terminal on each battery taking care not to short against chassis 2 Connect one end of the BLACK cable to the NEGATIVE terminal of the fully charged battery 3 Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery away from the fuel tank and battery To remove cables reverse order 1 Remove BLACK cable first from chassis and then from the fully charged battery 2 Remove RED cable last from both batteries 28 DIXON OPERATION Running 1 Release the parking brake by moving the lever downward Your mower is equipped with an operator presence system When the engine is running any attempt by the operator to leave the seat without
11. Do not drive up or down hills with 8011 670a Personal protective equipment machine to roll over slopes greater than 10 degrees And do not drive across any slopes D DIXON SAFETY 7 Use extra care while operating machine with grass catchers or other attachments they can affect the stability of the machine 8 Do not use on steep slopes 9 Do not try to stabilize the machine by putting your foot on the ground 10 Do not mow near drop offs ditches or embankments The machine could suddenly roll over if a wheel is over the edge or if the edge caves in 8011 509 Be extra cautious when driving on slopes Children Tragic accidents can occur if the operator is not alert to the presence of children Children are often attracted to the machine and the mowing activity Never assume that children will remain where you last saw them e Keep children out of the mowing area and in the watchful care of a responsible adult other than the operator e Be alert and turn machine off if a child enters the area e Before and while backing look behind and down for small children e Never carry children even with the blades shut off They may fall off and be seriously injured or interfere with safe machine operation Children who have been given rides in the past Never allow children to operate the machine may suddenly appear in the mowing area for another ride and be run over or backed over by the machine
12. Lack of power or drive after short term operation 3 High operation temperature Before starting make sure the transaxle transmission is at the proper oil level Procedures should be performed with the machine drive wheels off the ground then repeated under normal operating conditions 1 With the bypass valve open and the engine running slowly move the directional control in both forward and reverse directions 5 or 6 times As air is purged the oil level will drop 2 With the bypass valve closed and the engine running slowly move the directional control in both forward and reverse directions 5 to 6 times Check the oil level and add oil as required after stopping the engine 3 lt may be necessary to repeat Steps 1 and 2 until all the air is completely purged from the system Purging is complete when the transaxle moves forward and in reverse at normal speed Anti scalp Rollers Deck has anti scalp rollers Anti scalp rollers are properly adjusted when they are just slightly off of the ground when the deck is at the desired cutting height in the operating position Anti scalp rollers then keep the deck in the proper position to help prevent scalping in most terrain conditions IMPORTANT INFORMATION Adjust anti scalp rollers with the mower on a flat level surface 1 Adjust the deck to the desired cutting height see To Adjust Deck Cutting Height in the operation section of this manual 2 Using a 34 w
13. Lew SEKR I H gt x l TO IGNITION 7 SWITCH El I wis W G TO RH CCA Y LEVER RE Y KS W I TO SEAT I1 w 7 swicH E wie 0000 H rw I I COLOR CODE R RED R W RED W WHITE STRIPE lwhe G GREEN W y W G WHITE W GREEN STRIPE Lk sae Y YELLOW FE LEVER B BLUE YO W WHITE 56 DIXON TECHNICAL DATA Accessories BioClip attachment Mulch kit In order to implement improvements specifications and designs can be altered Collection system without prior notification Torque Specifications Note that no legal demands can be placed Engine crankshaft bolt 50 ft lb 67 Nm based on the information contained in these Deck pulley bolts 45 ft lb 61 Nm HEHN iat 75 ft lb 100 Nm Use only original parts for repairs The use of other parts voids the warranty Blade bolt 49 89 ft lb 60 75 Nm Do not modify or install non standard Standard 74 fasteners 9 ft lb 12 Nm equipment to the unit without consent from the Standard 16 fasteners 18 ft lb 25 Nm manufacturer Modifications to the unit may Standard s fasteners 33 ft lb 44 Nm cause unsafe operations or damage the unit Standard 7 16 fasteners 52 ft lb 70 Nm Standard 4 fasteners 80 ft lb 110 Nm When this product is worn out and no longer used it should be returned to the reseller or other party for recycling DIXON 57 Manufacturer Power Lubrication Oil capacity excluding filter
14. before operating Stop machine if anyone enters the area Never carry passengers The machine is only intended for use by one person Do not mow in reverse unless absolutely necessary Always look down and behind before and while backing Never direct discharged material toward anyone Avoid discharging material against a wall or obstruction Material may ricochet back toward the operator Stop the blades when crossing gravel surfaces Do not operate machine without the entire grass catcher discharge guard or other safety devices in place and working Slow down before turning Never leave a running machine unattended Always turn off blades set parking brake stop engine and remove keys before dismounting D DIXON WARNING This symbol means that important safety instructions need to be emphasized It concerns your safety 8011 512 Read the operator s manual before starting the machine 8011 513 Clear the area of objects before mowing 10 SAFETY Disengage blades when not mowing Shut off engine and wait for all parts to come to a complete stop before cleaning the machine removing the grass catcher or unclogging the discharge chute Operate machine only in daylight or good artificial light Do not operate the machine while under the influence of alcohol or drugs Watch for traffic when operating near or crossing roadways Use extra care when loading or unloading the machine into a trailer or
15. circuit if there is spilled fuel e Disconnect the chassis cable from the battery first and reconnect it last Do not make a bridge short circuit across the Risk of sparking starter relay to run the starter e Never use the machine indoors or in spaces lacking proper ventilation The exhaust fumes contain carbon monoxide an odorless poisonous and lethal gas e Stop and inspect the equipment if you run over or into anything If necessary make repairs before starting e Never make adjustments with the engine running The machine is tested and approved only with the equipment originally provided or recommended by the manufacturer Only use approved repair parts for the machine 8009 728 D DIXON SAFETY The blades are sharp and can cause cuts and gashes Wrap the blades or use protective gloves when handling them Check the parking brake s functionality regularly Adjust and service as necessary The mulch blades should only be used in familiar areas when higher quality mowing is desired Reduce the risk of fire by removing grass leaves and other debris that may have accumulated on the machine Allow the machine to cool before putting it in storage Regularly clean deck and underside of deck avoid spraying engine and electrical components with water Transport The machine is heavy and can cause serious crushing injuries Be extra cautious when it is loaded on or unloaded
16. during operation this is not possible refuel such equipment There is risk for burns if touched with a portable container rather than from a gasoline dispenser nozzle Allow engine and exhaust system to cool at least two 2 minutes before e Keep the nozzle in contact with the rim of the refueling fuel tank or container opening at all times until fueling is complete Do not use a nozzle lock open device e If fuel is spilled on clothing change clothing immediately e Never overfill fuel tank Replace gas cap and tighten securely e Donot start the engine near spilled fuel e Never use gasoline as a cleaning agent e If leaks arise in fuel system engine must not be started until problem has been resolved e Check the fuel level before each use and leave space for the fuel to expand as the heat from the engine and the sun may otherwise cause the fuel to expand and overflow D DIXON SAFETY General Maintenance Never operate machine in a closed area Keep all nuts and bolts tight to be sure the equipment is in safe working condition Never tamper with safety devices Check their proper operation regularly Keep machine free of grass leaves or other debris buildup Clean oil or fuel spillage and remove any fuel soaked debris Allow machine to cool before storing If you strike a foreign object stop and inspect the machine Repair if necessary before restarting Never make any adjustments or repairs
17. first setting the parking brake will shut off the engine 2 Move the steering controls to the neutral position N IMPORTANT INFORMATION The mower deck s anti scalp rollers should be evenly adjusted 3 Select the cutting height using the cutting height pedal WARNING A Ensure that no one is near mower when engaging blade switch Make sure the work area is free from objects that could be thrown by the rotating blades 4 Engage the mower deck by pulling out the blade switch 5 Move throttle control to full throttle not choke The machine s speed and direction are continuously variable using the two steering controls When both controls are in the neutral position the machine stands still By moving both controls an equal amount forward or backward the machine moves in a straight line forward or backward respectively In order for example to turn right while moving forward move the right control towards the neutral position The rotation of the right wheel is reduced and the machine turns to the right Turning on the spot can be achieved by moving one control backward behind the neutral position and carefully moving the other steering control forward from its neutral position 8050 821 8050 117 Select cutting height 8011 669 Engage mower deck DIXON 29 OPERATION Operating on hills Read the Safety Instructions Driving on Slopes in the Safety Instru
18. into contact with belts or belt pulley drive surfaces 8011 731 8011 732 Deck spindle DIXON 49 LUBRICATION Deck Outer Spindle Lubricate using a grease gun one zerk each side 2 3 strokes Use only good quality bearing grease Engine Oil Changing the Engine Oil The engine oil should be changed for the first time 8011 733 after 5 8 hours of operation Thereafter it should be Deck outer spindle changed every 50 hours IMPORTANT INFORMATION Used engine oil is a health hazard and must not be disposed of on the ground or in nature it should always be disposed of at a workshop or appropriate disposal location WARNING Engine oil can be very hot if it is drained directly after stopping the engine Allow the engine to cool somewhat first Avoid skin contact wash with soap and water in case of spills Place the machine on a flat surface Place a container under the engine vvhere the hose from the oil drain valve exits Remove the dipstick and open the drain valve Allow the oil to run out into the container Then close the oil drain valve Replace the oil filter if necessary Fill with new engine oil in accordance with Checking the Oil Level 8 Start the engine Run it for a few seconds Stop and re check the oil level N NER 8011 730 Oil drain valve 50 DIXON LUBRICATION Oil Level Check the oil level in the engine w
19. risk of the spark plugs fouling e Disengage the mower deck by depressing the blade switch e Raise the mower deck by depressing the pedal forward to the transport position e When the machine is standing still activate the parking brake by pulling the lever upward e Move the throttle to the minimum position tortoise symbol Turn the ignition key to the stop position e Move the steering controls outward e Remove key Always remove key when leaving the mower to prevent unauthorized use IMPORTANT INFORMATION Leaving the ignition switch in any other position than OFF will cause the battery to be discharged 32 DIXON Engaged parking brake 88011 668 8050 117 8050 823 OPERATION Manual Transport WARNING Make no adjustments without e the engine stopped e the ignition key removed e the parking brake activated Unlocking Transmission When pushing or pulling the mower be sure to engage the bypass linkages e Always turn off engine before engaging or disengaging the hydro release free wheel lever Never attempt to move the lever with the engine running e Lift the seat to access release levers Push the hydro release levers toward the rear of the machine and inward until notches lock in place on frame Release park brake To engage the transmissions move the release levers outward so they return to normal position Push lever in and lock notch on frame 2 p
20. s emission is stated in the chapter TECHNICAL DATA and on the decals Only machines for European Use protective glasses Use protective gloves market 6 DIXON SYMBOLS AND DECALS Read Shut off engine and Keep a safe Use on slopes No passengers Operator s remove key before distance from no greater Manual performing any the machine than 10 maintenance or repair work Whole body Severing of fingers Do not open or Careful backing up Careful going exposure to and toes remove safety watch for other forward watch for thrown objects shields while people other people engine is running DANGER KEEP HANDS AND FEET AWAY Moving sharp blades under cover DIXON 7 SAFETY AN ms THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH These instructions are for your safety Read them carefully General Operation 1 10 11 Read understand and follow all instructions on the machine and in the manual before starting Do not put hands or feet near rotating parts or under the machine Keep clear of the discharge opening at all times Only allow responsible adults who are familiar with the instructions to operate the machine Clear the area of any objects such as rocks toys and wire which could be picked up and thrown by the blades Be sure the area is clear of bystanders
21. scents steekiies ii valama kaja e 67 After the First 5 8 Hours mrui 68 25 H f SEV CE visors a aaa 69 50 Hour Service nnnnneneneneennnennne 70 100 Hour SOMVICG irnn as 71 300 Hour Service 20 0 0 ccccecceeeeeeeeeeeeeceeceeeeeeeneees 72 At Least Once Each Year cceeeeeeeeeeeeeeeeees 73 INTRODUCTION Congratulations Thank you for purchasing a Dixon ride on mower This machine is built for superior efficiency to rapidly mow primarily large areas A control panel easily accessible to the operator and a hydrostatic transmission regulated by steering controls both contribute to the machine s performance This manual is a valuable document Read the contents carefully before using or servicing the machine The following of instructions use service maintenance etc by all who operate this machine is important for the safety of the operator and others It can also considerably increase the life span of the machine and increase its resale value If you sell your machine be sure to give the operator s manual to the new owner The final chapter of this operator s manual provides a Service Journal Ensure that service and repair work are documented A well kept service journal reduces service costs for the maintenance and affects the machine s resale value Please contact your dealer for more information Take the operator s manual along when the machine is taken
22. spilled oil or fuel Do not store spill or use gasoline near an open flame WARNING The engine and the exhaust system become very hot during operation Risk for burns if touched Allow engine and exhaust system to cool at least two 2 minutes before refueling 20 DIXON 8050 106 Fuel tank IMPORTANT INFORMATION Experience indicates that alcohol blended fuels called gasohol ethanol or methanol can attract moisture which leads to separation and formation of acids during storage Acidic gas can damage the fuel system of an engine while in storage To avoid engine problems the fuel system should be emptied before storage of 30 days or longer Drain the gas tank start the engine and let it run until the fuel lines and carburetor are empty Use fresh fuel the next season See Storage Instructions for additional information Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur CONTROLS Ignition Switch The ignition key is placed on the driver s panel and is used to start and stop the engine IMPORTANT INFORMATION Do not run the starter for more than five seconds each time If the engine does not start wait about 10 seconds before retrying Choke Control The choke is used for cold starts to provide the engine with a richer fuel mixture Two choke options are available depending on model For units with a separate choke control pull the choke control knob up
23. tires are under or over inflated you cannot properly adjust your deck Four slots control the height and pitch of the mower deck The deck should be adjusted slightly higher in the rear Side to side adjustment e Raise the deck into the four inch 4 102 mm cutting position e Measure height from the bottom edge of the deck to the ground at both front corners Distance A should be the same or within 3 16 5 mm of an inch e If adjustment is necessary make adjustment to one side of the deck only To adjust loosen the locknut and move the mounting bolt up or down in the slot until both side to side measurements are equal Recheck measurements after adjustment Front Lift Arm Slotted Deck ee Hanger Plates Mounting Bolt Mounting Bolt Front to back adjustment To obtain the best cutting performance the deck should be adjusted so the front tip of the blades are approximately s 3 2 mm to 4 6 5 mm lower than the rear tip If the front tip is higher a poor quality cut will result Check blade height with blade facing front to rear Measure distance B at the front and rear tip of the blade Before making any necessary adjustments check to make sure that the deck is level side to side See Side to Side Adjustment in Maintenance section With the deck in the 4 100 mm cutting position measure the front and rear tip of each blade while facing front to rear To
24. to your dealer for service General In this operator s manual left and right backward and forward are used in relation to the machine s normal driving direction Continuous dedication to improve our products require that specifications and design are subject to change without notice Driving and Transport on Public Roads Check applicable road traffic regulations before transporting on public roads If the machine is transported you must always use approved fastening equipment and ensure that the machine is well anchored DO NOT operate this machine on public roadways 4 DIXON Towing Do not tow this machine it may cause damage to the drive system Do not tow any trailers etc with this mower They may jackknife or overturn causing damage to the mower and possible serious injury to the operator Operating This machine is constructed only for mowing grass on lawns and even ground without obstacles such as stones tree stumps etc The machine can also be used for other tasks when equipped with special accessories provided by the manufacturer Operating instructions for the accessories are provided with delivery All other types of uses are incorrect The manufacturer s directions concerning operation maintenance and repairs must be carefully followed Lawn mowers and all power equipment can be potentially dangerous if used improperly Safety requires good judgement careful use in accordance with these instru
25. truck Always wear eye protection when operating machine 8011 520 Data indicates that operators age 60 years and Never take passengers above are involved in a large percentage of riding mower related injuries These operators should evaluate their ability to operate the riding mower safely enough to protect WARNING themselves and others from serious injury Follow the manufacturer s recommendation for wheel weights or counterweights Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer birth Anyone who operates this machine must first defects or other reproductive system read and understand this Operation Manual damage The engine exhaust contains Local laws may regulate the age of the user carbon monoxide which is a odorless Keep machine free of grass leaves or other colorless poisonous gas Do not use debris buildup which can touch hot exhaust or the machine in enclosed spaces engine parts and burn Do not allow the mower deck to plow leaves or other debris which can cause buildup to occur Clean any oil or fuel spillage before operating or storing the machine Allow machine to cool before storage DIXON 9 SAFETY Personal Safety Equipment WARNING When using the machine approved personal protective equipment shown in illustrations shall be used Personal protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if an a
26. with the engine running Check grass catcher components and the discharge guard frequently and replace with manufacturer s recommended parts when necessary Mower blades are sharp Wrap the blade or wear gloves and use extra caution when servicing them Check brake operation frequently Adjust and service as required Maintain or replace safety and instruction labels as necessary Do not modify safety equipment Check regularly to be sure it works properly The machine must not be driven with defective or unmounted protective plates protective cowlings safety switches or other protective devices Do not change the settings of governors and avoid running the engine with overly high engine speeds If you run the engine too fast you risk damaging the machine components Be very careful when handling battery acid Acid on skin can cause serious corrosive burns If you spill battery acid on your skin rinse immediately with water Acid in the eyes can cause blindness contact a doctor immediately Be careful when servicing the battery Explosive gases form in the battery Never perform maintenance on the battery when smoking or near open flames or sparks The battery can explode and cause serious injury damage 8011 515 Never drive the machine in an enclosed space WARNING Use protective glasses for maintenance work WARNING The battery contains lead and lead compounds chemicals that are considered t
27. zero turn While moving in a forward direction first pull both control levers back until the mower stops or slows dramatically Then by alternating one lever slightly to the forward position and the other in the reverse position OPERATION Before Starting Read the sections Safety Instructions and Controls before starting the machine Perform the daily maintenance before starting see Maintenance Schedule in the Maintenance section Check that there is sufficient fuel in the fuel tank Adjust the seat to the desired position The following conditions must be fulfilled before the engine can be started The driver must be seated on the seat The blade switch for engaging the mower blades must be depressed The parking brake must be on Both steering controls must be in the locked outer neutral position Starting the Engine 1 Sit on the seat 2 Raise the mower deck with the foot pedal to the transport position 3 Activate the parking brake 4 Disengage the mower blades by depressing the blade switch Start conditions Raise the mower deck 8050 822 8050 117 THROTTLE Blade switch 8050 816 DIXON 25 OPERATION 5 Move the steering controls outward to the locked outer neutral position 8050 777 Steering controls in the outward locked neutral position 6 Move the throttle to the middle position I
28. 11 734 DIXON 51 TROUBLE SHOOTING Problem Cause The engine will not start Blade switch is engaged Ssteering controls are not locked in the neutral position Driver is not sitting in the driver s seat Parking brake is not activated Battery is dead Contamination in the carburetor or fuel line Fuel supply is closed or the shut off valve for the fuel tank is in the wrong position Clogged fuel filter or fuel line The starter does not turn the engine over Dead battery Poor contacts on the battery terminal cable connections Fuse blown Ignition system faulty Fault in the starter safety circuit See Checking the Safety System in the Maintenance Section The engine runs rough 52 DIXON Faulty carburetor Choke control is pulled out with a warm engine Defective valves Defective piston cylinder piston ring or cylinder head seal Cylinder head bolts are loose Clogged fuel filter or jet Clogged ventilation valve on the fuel cap Fuel tank nearly empty Defective spark plugs Spark plugs are loose Defective ignition cable Defective spark plug electrode Defective spark plug connection Rich fuel mixture or fuel air mixture Wrong fuel type Water in the fuel Clogged air filter Air trapped in hydraulic system TROUBLE SHOOTING Problem Cause The engine seems weak Clogged air filter Defective spark plugs Carburetor incorrectly adjusted
29. 9 Change the fuel filter 100 hours 10 Clean the cooling fins 100 hours Oo NO a F WN o 11 Check the engine valve clearance 12 Perform the 300 hour service at an authorized service workshop DIXON 73 SERVICE JOURNAL Action Date mtr reading stamp sign 74 DIXON SERVICE JOURNAL Action Date mtr reading stamp sign DIXON 75 SERVICE JOURNAL Action Date mtr reading stamp sign 76 DIXON SERVICE JOURNAL Action Date mtr reading stamp sign DIXON 77 DPCO ZTR P N 539 131911 R01 07 20 08
30. Air trapped in hydraulic system The engine overheats Clogged air intake or cooling fins Engine overloaded Poor ventilation around engine Defective engine speed regulator Soot in the combustion chamber Too little or no oil in the engine Defective spark plugs Pre ignition incorrect Air trapped in hydraulic system Battery not charging Poor contact with battery terminal cable connectors The machine moves slowly unevenly or not at all Parking brake on Bypass valve on pump open Drive belt for the transmission gears slack or has come off Air trapped in hydraulic system Mower deck not engaging Drive belt for the mower deck has come loose Contact for the electromagnetic coupling has loosened The blade switch is faulty or has come loose from the cable contact The fuse has blown Transaxle leaks oil Damaged seals housing or gaskets Air trapped in hydraulic system DIXON 53 Problem TROUBLE SHOOTING Cause Uneven mowing results Different air pressure in tires on left and right sides Bent blades Suspension for the mower deck is uneven Chain fixture has come loose Blades are dull Driving speed too high Grass is too long Grass collected under the mower deck The machine vibrates 54 DIXON The blades are loose The blades are incorrectly balanced The engine is loose STORAGE Winter Storage At the end of the mowing season th
31. Check adjust the parking brake 70 DIXON SERVICE JOURNAL Action Date mtr reading stamp sign 100 Hour Service Perform the 25 hour service Perform the 50 hour service Change the engine oil filter Clean replace the spark plugs Replace the fuel filter Clean the cooling fins on the engine and transmission Check V belts ON Oa BE WYN gt Change the air filter s paper cartridge Check tighten caster wheel axle bolts every 200 hours DIXON 71 SERVICE JOURNAL Action Date mtr reading stamp sign 300 Hour Service 1 on oa F ON Inspect the machine Come to agreement with the customer as to which additional work is to be carried out Perform the 25 hour service Perform the 50 hour service Perform the 100 hour service Check adjust the mower deck Clean the combustion chamber and grind the valve seats Check the engine valve clearance Replace the air cleaner s pre filter foam 72 DIXON SERVICE JOURNAL Action Date mtr reading stamp sign At Least Once Each Year Clean the engine s cooling air intake 25 hours Replace the air cleaner s pre filter foam 300 hours Replace the air filter s paper cartridge Change the engine oil 50 hours Replace the engine oil filter 100 hours Check adjust the cutting height Check adjust the parking brake 50 hours Clean Change the spark plugs 100 hours
32. DIXON 39 MAINTENANCE IMPORTANT INFORMATION Do not use compressed air to clean the air filter Do not wash the paper filter Do not oil the paper filter 4 Tap the paper filter against a fixed surface to remove dust If the paper filter is still dirty it must be replaced Refit the air filter as follows 1 Check that the seal on the bottom of the paper filter is whole 2 Mount the paper filter in the air filter housing and tighten the wing nuts 3 Refit the pre filter on the paper filter 4 Replace the cowling over the air filter housing Do not over tighten the plastic fastener Fuel Filter Replace the line mounted fuel filter every 100 hours once per season or more regularly if it is clogged Replace the filter as follows 1 Move the hose clamps away from the filter Use flat nosed pliers 2 Pull the filter loose from the hose ends 3 Push the new filter into the hose ends Position the filter with the FLOW arrow pointing up toward the carburator If necessary a soap solution can be applied to the filter ends to ease mounting 4 Move the hose clamps back toward the filter Fuel Pump Air Filter Regularly check that the fuel pump s air filter is free from dirt Remove the screws and open the pump no hoses need be removed The filter can be cleaned with a brush if necessary Replace the filter on the console 40 DIXON 8009 181 Remove dust 8009 146 Fuel filter
33. Oil capacity including filter Engine oil Synthetic Engine oil Mineral Class Fuel tank capacity Spark plugs gap Cooling Air filter Alternator Starter Transmission Speed and direction controls Speed forward Speed reverse TECHNICAL DATA ZTR 44 968999538 ZTR 36 968999539 20 hp 16 hp Pressure with oil filter Pressure with oil filte 1 6 qt 1 5 liters 1 3 qt 1 3 liters SAE 10W30 SAE 5W30 10W30 winter SAE SW 30 SAE 30 winter 10W30 PI SJ SH SG API SF SJ SH SG Min 87 octane unleaded Max Min 86 octane unleaded methanol 10 max MTBE 15 Max methanol 5 max ethanol 10 Max MTBE 15 4 5 gallon 17 liters 4 5 gallon 17 liters 030 0 75 mm 030 0 75 mm EE EE en mem oop As rated by the engine manufacturer 58 DIXON TECHNICAL DATA p 2 441 968999538 ZTR36 968999539 C AAA AAA ETEA EAA SAA TAA AAA AAA DT AAA AAA DIXON 59 TECHNICAL DATA po 2 TR GI 968999609 ZTR44 968999611 Ensine I Oil capacity excluding filter 1 875 gts 1 8 liters Oil capacity including filter 1 5 gt 1 42 liters 2 qt 1 91 liters Engine oil Synthetic SAE 5W30 10W30 SAE 5W30 10W30 Engine oil Mineral Class SAE 30 winter 10W30 SAE 30 winter 10W30 API SF SJ SH SG API SF SJ SH SG Fuel Min 86 octane unleaded Max Min 86 octane unleaded Max methanol 10 max MTBE 15 J methanol 10 max MTBE 15 Fuel tank capacity 4 5 gallon 17 liters 4 5 gallon 17 li
34. adjust loosen the jam nut on the yoke remove the securing ring and push the clevis pin out while supporting the deck To lower that specific corner lengthen the rod assembly by turning the yoke counter clockwise To raise that specific corner shorten the rod assembly by turning the yoke clockwise Reinstall clevis pin and recheck dimension Once front to back adjustment is correct reinstall securing rings and secure jam nuts DIXON 45 MAINTENANCE Caster Wheels Check every 200 hours Lift front of unit off of ground so caster wheels can rotate freely Tighten caster bolt then back off 4 turn Check that wheel rotates freely If wheel does not rotate freely back the caster bolt off in Ya turn increments until wheel rotates freely Foam filled tires or solid tires will void the warranty IMPORTANT INFORMATION DO NOT add any type of tire liner or foam fill material to the tires Excessive loads created by foam filled tires will cause premature failures Only use O E M specified tires Hardware 1 Nut NU Check daily Inspect the entire machine for loose or 2 Bolt missing hardware 3 Sleeve Caster wheels Cleaning Regular cleaning and washing especially under the mower deck will increase the machine s lifespan Make ita habit to clean the machine directly after use after it is cooled before the dirt sticks Do not spray water on the top of the mower deck Use compressed air to clean the top side of mower
35. attery from the mower 7 Install new battery with terminals in the same position as the old battery 8 Reinstall battery hold down and secure with nuts removed in Step 5 9 First connect RED battery cable to positive battery terminal with hex bolt and hex nut 10 Connect BLACK grounding cable to negative battery terminal with remaining hex bolt and hex nut 11 Tighten securely 12 Lower seat 36 DIXON Always use protective glasses when handling the battery IMPORTANT INFORMATION Do not attempt to open or remove caps or covers Adding or checking level of electrolyte is not necessary Always use two wrenches for the terminal screws WARNING Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time Before connecting battery remove metal bracelets wristwatch bands rings etc Positive terminal must be connected first to prevent sparks from accidental grounding 8050 109 Remove battery hold down to replace battery MAINTENANCE Ignition System The engine is equipped with an electronic ignition system Only the spark plug requires maintenance For recommended spark plug see Technical Data 1 Remove the ignition cable boot and clean around the spark plug 2 Remove the spark plug with a spark plug socket wrench 3 Check the spark plug Replace the spark plug if fouled the electrodes are burned and if the insulation
36. ccident does happen Ask your retailer for help in choosing the right equipment Make sure that you have first aid equipment close at hand when using the machine e Never use the machine when barefoot e Always wear protective shoes or boots preferably with steel toe caps e Always wear approved protective glasses or a full visor when assembling or driving e Always wear gloves when handling the blades Never wear loose clothing that can get caught in moving parts e Use ear protectors to avoid damage to hearing Slope Operation Slopes are a major factor related to loss of control and tip over accidents which can result in severe injury or death Operation on all slopes requires extra caution If you cannot back up the slope or if you feel uneasy on it do not mow it 1 Mow up and down slopes 10 degrees maximum not across 2 Watch for holes ruts bumps rocks or other hidden objects Uneven terrain could overturn the machine Tall grass can hide obstacles 3 Choose a low ground speed so that you will not have to stop while on the slope 4 Do not mow on wet grass Tires may lose traction 5 Avoid starting stopping or turning on a slope If the tires lose traction disengage the blades and proceed slowly straight down the slope 6 Keep all movement on the slopes slow and 6003 004 gradual Do not make sudden changes in Mow up and down not side to side speed or direction which could cause the 4 WARNING
37. ch mrmraa 21 Choke Control SAMASUST 21 Throttle Control umrn 21 Blade SWilG fierecon 22 Circuit Breaker ssneeeeerrnerrrreseeernnssrrnnnannna 22 Parking BraK erencnsnanasraninnnn ka eea vad 22 Mower Deck Cut Height Adjustment 23 OPERATION eccriene 24 MGANUN E E TO E ka E 24 SEa E E TE 24 Before Starting trramns 25 starting the ENGING sive tuvivseveivi ava tama va vake umaa e 25 Weak Battery 28 Jumper Cables 14134445 immi its ngi 28 Running erenn a ia 29 Operating On NUNS eerren sinen 30 MOWING TIPS mmiminemeeeeenaennannanan emane 31 Stopping the Engine vmemvensennnntetavnnannsa 32 Manual Transport emeenennenennanena 33 MAINTENANCE vices tirtiivmteritvamtaamv nam maamavt ataman ama 34 Maintenance Schedule ms 34 Battery wisitssctactivteccennitistiediet vaada A eee 36 Ignition System mmrannraa 37 Safety System ecs 37 Engine Cooling Air Intake u 38 Throttle Cables sen inanan 38 Choke Cablle cccccccccccccccccceeeeeeeeeeeseeeeseeaeaeaeaes 38 Alt Filteren Ram ais 39 Fuel Filter seisi arina nian ann nia 40 Fuel Pump Air Filter 40 Tire Pressures 0 ccccccccccccceeeeseeseaeaeeeseeeeaeaeeeeseeees 41 Parking Brake eccna 41 VEPEMS eis ms la kk kad aa 41 Pump Belt escena tracncsstevesdcacneaaa
38. ctions e The slowest speed possible should be used before starting up or down hills e Avoid stopping or changing speed on hills e If stopping is absolutely necessary pull drive levers into the neutral position and push to the outside of the unit and engage the parking brake WARNING kaa Do not drive up or down hills with Stopping conditions slopes greater than 10 degrees Do not drive across slopes e To restart movement release the parking TR brake KE AC Pull the control levers back to the center of the mower and press forward to regain forward motion e Make all turns slowly IMPORTANT INFORMATION Control levers return to neutral when released This may cause the mower to suddenly stop 8050 783 Released parking brake 30 DIXON Mo OPERATION wing Tips Observe and flag rocks and other fixed objects to avoid collisions Begin with a high cutting height and reduce it until the desired mowing result is attained The average lawn should be cut to 2 64 mm during the cool season and over 3 76 mm during the hot months For healthier and better looking lawns mow often after moderate growth For best cutting performance grass over 6 15 cm in height should be mowed twice Make the first cut relatively high the second to the desired height The mowing result will be best with a high engine speed the blades rotate rapidly and low speed the rider moves slowly If the grass i
39. ctions and common sense The machine must only be operated maintained and repaired by persons familiar with the machine s special characteristics and who are also knowledgeable about the safety instructions Use only approved repair parts to maintain this machine Accident prevention regulations other general safety regulations occupational safety rules and traffic regulations must be followed without fail Unauthorized modifications to the design of the machine may absolve the manufacturer from liability for any resulting personal injury or property damage INTRODUCTION Good Service Dixon s products are sold only in specialized retail stores with complete service This ensures that you as a customer receive only the best support and service Before the product is delivered the machine has for example been inspected and adjusted by your retailer See the certificate in the Service Journal in this operator s manual When you need spare parts or support in service questions warranty issues etc please consult the following professional This Operator s Manual belongs to the machine with Engine Transmission the manufacturing number Manufacturing Number The machine s manufacturing number can be found on the printed plate affixed to the left in the engine compartment Stated on the plate from the top are The machine s type designation 1 D e The manufacturer s type number Model The
40. deck Regulary clean deck and underside of deck avoid spraying engine and electrical components with water Do not rinse hot surfaces with cold water Let unit cool before washing Use protective glasses when cleaning and washing 8050 092 Cleaning 46 DIXON MAINTENANCE Tracking Adjustment If the mower is not tracking straight check the air pressure in both rear tires Recommended air pressure is 15 psi 1 bar If the unit will not track straight follow the steps below Tracking must be checked on a flat and level concrete or blacktop surface Mower is tracking to the right Increase the air pressure 2 3 psi 0 1 0 2 bar in the right rear tire or decrease the air pressure 2 3 psi in the left rear tire Mower is tracking to the left Increase the air pressure 2 3 psi 0 1 0 2 bar in the left rear tire or decrease the air pressure 2 3 psi in the right rear tire Recheck tracking and keep making adjustments with the tire pressure until the unit tracks straight DO NOT exceed maximum recommended tire pressure 24 psi 1 6 bar Record the tire pressure for future reference EZT Transaxle Purging Procedure Due to the effects air has on efficiency in hydrostatic drives it is critical that it is purged from the system Purge procedures should be done any time a hydrostatic system has been opened for maintenance or for adding oil to the system Symptoms in hydrostatic systems may be 1 Noisy operation 2
41. e ROPS is an accessory Donot use ROPS as a lifting attaching or anchoring point e Donot use ROPS for wrecking or towing e Donot exceed Max GVW 2822 Ibs 1283 kg e Read machine operator s manual before each use e Securely fasten your seat belt if the unit has a ROPS e Where possible avoid operating the unit near ditches embankments and holes e Reduce speed when turning crossing slopes and on rough slick or muddy surfaces e Stay off slopes too steep for safe operation e Watch where you are going especially at row ends on roads and around trees Do not permit others to ride e Operate the mower smoothly no jerky turns starts or stops When mower is stopped set brakes securely and use park brake e If any part of ROPS is damaged the entire ROPS must be replaced e Check all bolts including seat belt for correct torque before each use e Check ROPS structure for damage before each use e ROPS bar is NOT intended for use in sub zero temperatures D DIXON SAFETY WARNING The rollover protection system s capabilities may be impaired by damage if the mower is overturned or if alteration to the ROPS occurs If these conditions take place the total structure MUST be replaced WARNING This mower is equipped with an internal combustion engine and should not be used on or near any unimproved forested bush covered or grassy lands unless the engine s
42. e machine should be readied for storage or if it will not be in use for longer than 30 days Fuel allowed to stand for long periods of time 30 days or more can leave sticky residues that can plug the carburetor and disrupt engine function Fuel stabilizers are an acceptable option as regards to the sticky residues that can occur during storage Add stabilizer to the fuel in the tank or in the storage container Always use the mixing ratios specified by the manufacturer of the stabilizer Run the engine for at least 10 minutes after adding the stabilizer so that it reaches the carburetor Do not empty the fuel tank and the carburetor if you have added stabilizer WARNING Never store an engine with fuel in the tank indoors or in poorly ventilated spaces where fuel vapor can come in contact with open flames sparks or a pilot light such as in a boiler hot water tank clothes drier etc Handle the fuel with care It is very flammable and can cause serious personal injury and property damage Drain the fuel into an approved container outdoors and far away from open flame Never use gasoline for cleaning Use a degreaser and warm water instead To ready the machine for storage follow these steps 1 Thoroughly clean the machine especially under the mower deck Touch up damage to the paint and spray a thin layer of oil on the underside of the mower deck to avoid corrosion 2 Inspect the machine for worn or damaged parts a
43. eys and remove belt Deck belt installation NOTE For ease in installing the deck belt refer to the routing decal on bottom of seat Wrap the deck belt around the electric clutch pulley that is located on the engine shaft Route the belt forward between the EZT E Series Zeroturn Transaxles and up onto the deck Place belt around spring loaded idler pulley Wrap the belt around the stationary idler pulley and around the mandrel housings Push inward on the idler arm and carefully route belt over stationary idler pulley Once belt is properly routed slowly release idler arm to tension belt Double check belt routing to make sure it matches the routing decal and the belt does not have any twist Correct as needed Adjust tension with deck eyebolt Replace belt shields on both mandrel housings and secure with fasteners 42 DIXON 8050 824 1 Shield bolts 2 Belt shields Removing deck belt 8050 825 1 Clutch pulley 2 Deck belt Belt routing deck belt 44 deck 8050 826 1 Clutch pulley 2 Deck belt Belt routing deck belt 36 and 42 deck MAINTENANCE Pump Belt Replacing EZT E Series Zeroturn Transaxle belt Park the mower on a level surface Engage the parking brake EZT belt removal NOTE Be careful not to damage the fan blades on the EZT s as this can affect cooling or damage the EZT s e Remove the deck belt see Deck Belt Removal in this section o
44. f the engine is cold the throttle control should be pushed forward to its choke position For units with a separate choke control pull the choke control knob up THROTTLE 8050 816 Set the throttle 7 Press in and turn the ignition key to the start position 8050 780 Turn to the start position 26 DIXON OPERATION 8 When the engine starts immediately release the ignition key back to the run position IMPORTANT INFORMATION Do not run the starter for more than 5 seconds each time If the engine does not start wait about 10 seconds before retrying 9 Set the desired engine speed with the throttle Allow the engine to run at a moderate speed half throttle for 3 5 minutes before loading it too heavily USE FULL THROTTLE WHEN MOWING no choke WARNING Engine exhaust and certain vehicle components contain or emit chemicals considered to cause cancer birth defects or other reproductive system damage The engine exhaust contains carbon monoxide which is a odorless colorless poisonous gas Do not use the machine in enclosed spaces 8050 781 Return to run position 8050 818 Set the engine speed DIXON 27 OPERATION Weak Battery A WARNING Lead acid batteries generate explosive gases Keep sparks CC i tual mga
45. f the manual e Create slack in the belt by removing the spring on the pump idler arm e The belt should now be able to be removed from the engine pulley and EZT pulleys Belt installation e Wrap the EZT belt around the EZT pulleys e Route the belt around the inside of the idler pulley e Wrap the belt around the engine pulley e Reattach the spring on the pump idler arm e Install clutch on to engine shaft pulley side down make sure key is installed and align the clutch anti rotation tab into slot on clutch Secure clutch install wire e Reinstall the deck belt onto the electric clutch belt see Deck Belt Removal in this section of the manual DIXON 43 MAINTENANCE Blades In order to attain the best mowing effect it is important that the blades are well sharpened and not damaged WARNING Blades are sharp Protect your hands with gloves and or wrap blades with a heavy cloth when handling Bent or cracked blades or blades with large nicks should be replaced Check the blade mounts Damaged blades should be replaced when hitting Check the blades obstacles that result in a breakdown Let the service workshop decide whether the blade can be repaired ground or must be replaced 8011 604 IMPORTANT INFORMATION The sharpening of blades should be carried out by an authorized service workshop Blade replacement e Remove blade bolt by turning counterclockwise e Install new or re
46. from a vehicle or trailer Use an approved trailer to transport the machine Activate the parking brake turn off the fuel supply and fasten the machine with approved fastening devices such as bands chains or straps when transporting Do not operate this machine on public roadways Check and abide by local traffic regulations before transporting the machine on any road Do not tow this machine it may cause damage to the drive system Do not tow any trailers etc with this mower They may jackknife or overturn causing damage to the mower and possibly serious injury to the operator Load the unit onto truck or trailer by driving up ramps of suitable strength using a slow speed Do not lift The machine is not intended to be lifted by hand 8011 514 Regularly clean deck WARNING Escaping hydraulic oil under pressure can have sufficient force to penetrate the skin causing serious injury If injured by escaping fluid see a doctor at once Serious infection or reaction can develop if proper medical treatment is not administered immediately IMPORTANT INFORMATION The parking brake is not sufficient to lock the machine in place during transport Ensure that the machine is well fastened to the transport vehicle Always reverse the machine onto the transport vehicle to avoid tipping it over DIXON 15 Roll Over Protection System ROPS The ROPS increases the basic weight of the unit by 42 Ibs 19 kg Th
47. g forward move the right control towards the neutral position The rotation of the right wheel is reduced and the machine turns to the right Zero turn can be achieved by moving one control backward behind the neutral position and carefully moving the other steering control forward from its neutral position The rotation direction when zero turning is determined by which steering control is moved backward behind the neutral position If the left steering control is pulled backward the machine turns WARNING to the left Use extra care when using this maneuver The machine can turn very rapidly if one steering control is moved much further forward than the other 8050 106 Steering controls Tracking If the mower is not tracking straight check the air pressure in both rear tires Recommended air pressure is 15 psi 1 bar Tracking must be checked on a flat and level concrete or blacktop surface If unit still does not track straight contact a Dixon dealer for adjustment 8050 166 1 Forward Neutral Neutral slot Neutral lock Reverse Motion control lever pattern right side Pons 18 DIXON CONTROLS Seat Adjustment Lever The seat can be adjusted lengthways When making adjustments sit on the seat Slide the lever to the side and maneuver seat to appropriate placement and release lever Bypass Linkage Unlocking Transmission When pushing or pulling the mower be sure to engage the bypass linkages
48. he clamping screw for the cable s outer casing and move the choke lever to the full choke position 2 Check that the choke cable is mounted in the upper lever see illustration Push the choke cable s outer casing as far to the right as possible and tighten the clamping screw 38 DIXON 8011 625 8011 554 Adjusting the throttle cable 8011 555 Adjusting the choke cable MAINTENANCE Air Filter If the engine seems weak or runs unevenly the air filter may be clogged If run with a dirty air filter the spark plugs can become fouled disrupting operation For this reason it is important to replace the air filter regularly see the heading Maintenance Schedule for the proper service interval WARNING The engine and the exhaust system become very hot during operation There is a risk for burns if touched Allow engine and exhaust system to cool at least two 2 minutes Cleaning replacing the air filter is carried out as follows 1 Remove the plastic fastener on the top of the air filter cowling and remove the air filter cowling 2 Remove the foam rubber pre filter and clean using a mild detergent Squeeze it dry with a clean cloth 3 Remove the wing nuts for the air filter and remove the paper filter 8011 768 8011 557 Remove pre filter 8011 558 Remove paper filter
49. hen the machine is standing level and the engine is stopped Remove the dipstick wipe it clean and then replace it The dipstick should be screwed into place Take the dipstick out again and read the oil level API class SF SG SH SJ or higher must be used Syntetic oil SAE 5W 30 or 10W 30 is recommended at all temperatures Mineral oil SAE 5W 30 10W 30 can be used between 18 C 0 F and 5 C 40 F At temperature above 5 C 40 F single grade SAE 30 must be used The engine holds 0 88 qt 1 0 liters of oil excluding the filter including filter 2 qt 1 9 liters The oil level should lie between the markings on the dipstick If the level is approaching the ADD mark fill the oil to the FULL mark on the dipstick Never fill to above the FULL mark The oil is filled through the hole for the dipstick Oil Filter 1 Drain the engine oil in accordance with the work description under the heading Engine Oil Change Engine Oil 2 Remove the oil filter If necessary use a filter remover 3 Wipe new clean engine oil onto the seal for the new filter 4 Mount the filter by hand with 3 4 turn 5 Run the engine warm then check that there are no leaks around the oil filter seal 6 Check the oil level in the engine fill if necessary The oil filter holds 0 1 qt 0 1 liters of oil Remove the dipstick 8011 500 The dipstick markings Changing the oil filter 8009 159 80
50. ing height it is important that the air pressure in all four tires is the same 15 psi 1 bar DIXON 23 OPERATION Read Safety Instructions section and following pages if you are unfamiliar with the machine Training Zero turn mowers are far more maneuverable than typical riding mowers due to their unique steering capabilities We suggest that this section be reviewed in its entirety prior to attempting to move the mower under its own power Additionally we suggest when first operating the mower use a reduced throttle speed and reduced ground speed by NOT moving control levers to the furthest forward or reverse positions during initial operation or until operator becomes comfortable with controls We also suggest first time users or new users to Zero Turn mowers to become familiar with the mower s movement on a hard surface such as concrete or blacktop PRIOR to attempting to operate on turf Until operator becomes comfortable with mower controls and zero turning capability they may damage turf due to overly aggressive maneuvers IMPORTANT INFORMATION When control levers are in the reverse position they return to neutral when released This may cause the mower to suddenly stop Steering To move forward and backward The direction and speed of the mower s movements is effected by the movement of the control lever s on each side of mower The left control lever controls the left wheel The right contr
51. is cracked or damaged Clean the spark plug with a steel brush if it is to be reused 4 Measure the electrode gap with a gapping tool The gap should be 030 0 75 mm Adjust as necessary by bending the side electrode 5 Reinsert the spark plug turning by hand to avoid damaging the threads 6 After the spark plug is seated tighten it using a spark plug wrench so that the washer is compressed A used spark plug should be turned 1 8 of a turn from the seated position A new spark plug should be turned 34 turn from the seated position 7 Replace the ignition cable Safety System The machine is equipped with a safety system that prevents starting or driving under the following conditions The engine can only be started when The mower deck is disengaged The steering controls are in the outer locked neutral position e The driver is sitting in the driver s seat The parking brake is on Make daily inspections to ensure that the safety system works by attempting to start the engine when one of the conditions is not met Change the conditions and try again If the machine starts when one of these conditions is not met turn the machine off and repair the safety system before using the machine again Make sure the engine stops when the parking brake is not engaged and the operator leaves the seated position e Check that the engine stops if the mower blades are engaged and the driver temporarily stands up
52. ist e Engage the parking brake e Place the Blade switch in the disengaged position e Turn the ignition switch to OFF position and remove the key Make sure the blades and all moving parts have completely stopped Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug DIXON 35 MAINTENANCE Battery Your mower is equipped with a maintenance free battery and does not need servicing However periodic charging of the battery with an automotive type battery charger will extend its life 1 Keep battery and terminals clean 2 Keep battery bolts tight 3 Recharge at 6 10 amperes for 1 hour Cleaning battery and terminals Corrosion and dirt on the battery and terminals can cause the battery to leak power 1 Lift seat and rotate forward 2 Disconnect BLACK battery cable first then the RED battery cable and remove the battery from the machine 3 Rinse the battery with plain water and dry 4 Clean terminals and battery cable ends with wire brush until shiny 5 Coat terminals with grease or petroleum jelly 6 Reinstall battery Replacing battery 1 Lift seat and rotate forward 2 Open terminal access doors 3 Using two 4 wrenches disconnect BLACK battery cable then RED battery cable 4 Position deck to lowest setting 5 Front underside of frame remove the nuts that secure the battery hold down 6 Carefully remove the b
53. k the idle speed Check the engine high idle speed Inform the customer about The need and advantages of following the service schedule The need and advantages of leaving the machine for service every 300 hours The effects of service and maintaining a service journal on the machine s resale value Application areas for Mulching 15 Fill in the sales papers etc Delivery service has been carried out No remaining notes Certified DIXON 67 SERVICE JOURNAL Action Date mtr reading stamp sign After the First 5 8 Hours 1 Change engine oil 68 DIXON SERVICE JOURNAL Action Date mtr reading stamp sign 25 Hour Service Check the fuel pump s air filter Check the tire pressures Check battery with cables Lubricate according to lubrication chart NO aA FON gt Clean the air cleaner s pre filter foam Sharpen Replace mower blades if required Check clean the engine s cooling air intake DIXON 69 SERVICE JOURNAL Action Date mtr reading stamp sign 50 Hour Service 1 Perform the 25 hour service 2 Clean replace the air cleaner s filter cartridge paper filter shorter intervals for dusty operating conditions Change engine oil 4 Lubricate according to lubrication chart
54. laces 8050 811 Bypass linkages DIXON 33 MAINTENANCE Maintenance Schedule The following is a list of maintenance procedures that must be performed on the machine For those points not described in this manual visit an authorized service workshop An annual service carried out by an authorized service workshop is recommended to maintain your machine in the best possible condition and to ensure safe operation Read Maintenance in the Safety Instructions section Described in this manual 4 Not described in this manual 1 First change after 5 8 hours When operating with a heavy load or at high ambient temperatures replace every 50 hours In dusty conditions cleaning and replacement are required more often 2 Performed by authorized service workshop Daily Weekly At Maintenance interval least in hours once Maintenance Before After each year 25 50 100 300 Check the parking brake Check the engine s oil level every refueling Check the safety system 0 0 Check for fuel and oil leakages Check clean the engine s cooling air intake Check the mower deck Check for loose hardware screws nuts Clean under the mower deck Start the engine and blades listen for unusual sounds Check for damage Thoroughly clean around the engine 9 9 0 0 0 0 Clean around belts belt pulleys Check the tire pressures Check battery
55. machine s serial number Serial no Please have the type designation and serial number available when ordering spare parts The engine s manufacturing number is stamped on one of the valve covers The plate states e The engine s model e The engine s type Code Please have these available when ordering spare parts DIXON 5 SYMBOLS AND DECALS These symbols are found on the machine and in the operator s manual Study them carefully so that you know what they mean WARNING XXXX XXXXXX XXXXX XXXX XXXXXXXXX XXXXXX XXXXXXXXX XX XXXXXXXX XXXX XXXXXX Used in this publication to notify the reader of a risk of personal injury or death particularly if the reader should neglect to follow instructions given in the manual IMPORTANT INFORMATION XXXX XXXXXX XXXXX XXXX XXXXXXXXX XXXXXxX XXXXXXXXX XX XXXXXXXX XXXX XXXXXX Used in this publication to notify the reader of a risk of material damage particularly if the reader should neglect to follow instructions given in the manual Used also when there is a potential for misuse or misassembly Reverse Neutral Fast Warning Parking Brake CE conformity Warning Rotating blades Do not touch parts marking Only for keep away from the European market discharge deck le Battery acid is corrosive explosive and flammable Do not stand here Noise emissions to the surroundings in accordance with the European Union s directive The machine
56. nd tighten any nuts or screws that may have become loose 3 Change the engine oil dispose of properly 4 Empty the fuel tanks or add a fuel stabilizer Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor 5 Remove the spark plug and pour about a tablespoon of engine oil into the cylinder Turn over the engine so that the oil is evenly distributed and then refit the spark plug 6 Lubricate all grease zerks joints and axles 7 Remove the battery Clean charge and store the battery in a cool place but protect it from direct cold 8 Store the machine in a clean dry place and cover it for extra protection Service When ordering spare parts please specify the purchase year model type and serial number Always use genuine Dixon spare parts An annual check up at an authorized service workshop is a good way to ensure that your machine performs its best the following season DIXON 55 SCHEMATIC TO LH BRAKE TO ALT rm _SWITCH HD TO ENGINE SHUT i POL CG OFF R G GROUND ie LL RA TO RH aRAKE rosam Wel MES W y rh W mi 005 1 Kp Y G i i Ll I H i TO ELECTRIC 5B i CLUTCH woo 1 I L wG OS eren TO CIRCUIT BREAKER OM i I bd od I I I W G H i W G TOCLUTCH I SVVITCH EE G n E l l Y Y CRM It Bi
57. nward to release it The park brake is designed to hold the mower from moving and is not intended for use in stopping the mower while it is in motion The engine will stop if the park brake is engaged while the control levers are in the drive position IMPORTANT INFORMATION The machine must stand absolutely still when applying the parking brake Always set the parking brake before dismounting Release the parking brake before moving the mower 22 DIXON 8050 816 Blade switch THROTTLE 8050 816 8050 823 Engaged parking brake CONTROLS Mower Deck Cut Height Adjustment Located on the right front of the frame the lift lever pedal controls the cutting height The deck cutting height is obtained by pressing the foot pedal forward to lift the deck To lower the deck apply pressure to the top side of the foot pedal and allow it to pivot into the desired cutting height notch Secure the desired cut height with pin The cutting height range is from 172 38 mm to 5 140 mm in 72 13 mm increments The heights are measured from the ground up to the blade tip with the engine not running 8050 806 Cut height lift pedal IMPORTANT INFORMATION Always use the high position to transport IMPORTANT INFORMATION In order to obtain an even cutt
58. o cause cancer birth defects and other reproductive system damage Wash your hands after handling the battery DIXON 13 SAFETY e Ensure that nuts and bolts especially the fastening bolts for the blade attachments are properly tightened torqued and that the P em CANALS GJ equipment is in good condition 1 e Donot modify safety equipment Check a you risk damaging the machine components e Sparking can occur when working with the battery and the heavy cables of the starter i i 6003 009 circuit This can cause battery explosion fire or Do not smoke when performing maintenance on the battery EA ENN DE A The battery can explode and cause serious injury damage eye injury Sparking in this circuit can not occur after the chassis cable normally negative black is removed from the battery p gu regularly to be sure it works properly The machine must not be driven with defective or unmounted protective plates protective cowlings safety switches or other protective devices e Do not change the settings of governors and avoid running the engine with overly high engine speeds If you run the engine too fast WARNING Avoid electrical sparking and its consequences by the following routines Use protective goggles e Ensure that the fuel filler cap is mounted tightly and no flammable substances are stored in an open vessel e Never work with the starter
59. ol lever controls the right wheel First time users should push mower see Moving by Hand in the Operation section to an open flat area without other people or vehicles obstacles nearby In order to move unit under its own power the operator must be in the seat start engine see Before Starting in Operation section adjust engine speed to idle disengage parking brake do not engage blades at this time rotate control levers inward As long as 24 DIXON the control levers have not been moved forward or backwards mower will not move Slowly move both control levers forward slightly This will allow mower to start moving forward in a straight line Pull back on control levers to the neutral position and mower should stop moving Pull back slightly on control levers this will allow mower to start moving backwards Push forward on control levers to the neutral position and mower should stop moving To turn to the right While moving in a forward direction pull the right lever back towards the neutral position while maintaining the position of the left lever this will slow the rotation of the right wheel and cause the machine to turn in that direction To turn to the left While moving in a forward direction pull the left lever back towards the neutral position while maintaining the position of the right lever this will slow the rotation of the left wheel and cause the machine to turn in that direction To
60. rench and a 15 wrench remove the nut and shoulder bolt from the anti scalp roller 3 Lower the anti scalp roller to the ground and raise it up to the next highest hole 4 Replace and tighten the nut and shoulder bolt 5 Be sure to adjust all of the anti scalp rollers to the same position 6 Be sure to readjust the anti scalp rollers if the cutting height is changed IMPORTANT INFORMATION The anti scalp rollers must not be used for gauge wheels or the roller and deck may be damaged DIXON 47 LUBRICATION Lubrication Schedule ai Y 12 12 Every year Lubricate with oil can 8011 672 3 Lubricate with grease gun Oil change yw Filter change Pg 1 52 Every Week 1 365 Every day Level check Change transaxles transmission filters General Remove the ignition key to prevent unintentional movements during lubrication When lubricating with an oil can it must be filled with engine oil When lubricating with grease unless otherwise stated use a high grade molybdenum disulfide grease For daily use the machine should be lubricated twice weekly Wipe away excess grease after lubrication It is important to avoid getting lubricant on the belts or the drive surfaces on the belt pulleys Should this happen attempt to clean them with spirits If the belt continues to slip after cleaning it must be replaced Gasoline or other petroleum products must not be used to clean belts 48 DIXON
61. s not too long and dense the driving speed can be increased without negatively affecting the mowing result The finest lawns are obtained by mowing often The lawn becomes more even and the grass clippings more evenly distributed over the mown area The total time taken is not increased as a higher operating speed can be used without poor mowing results Avoid mowing wet lawns The mowing result is poorer because the wheels sink into the soft lawn clumps build and the grass clippings fasten under the cowling Hose the mower deck underside with water after each use When cleaning the mower deck shall be raised into the transport position Make sure the mower is cooled and the engine is off Use compressed air to clean top surface of the deck Avoid flooding water on top surface engine and electrical components When the mulching kit is used it is important that the mowing interval is frequent WARNING Clear the lawn of stones and other objects that can be thrown out by the blades 8050 819 Mowing pattern WARNING Never drive the rider on terrain that slopes more than 10 degrees Mow slopes up and down never side to side Avoid sudden directional changes DIXON 31 OPERATION Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it if it has been worked hard Avoid idling the engine for longer periods as there is a
62. sharpened blade with stamped GRASS SIDE facing towards ground grass down or THIS SIDE UP facing deck and cutter housing e Install and tighten blade bolt securely Torque blade bolt to 27 35 ft lb 35 45 Nm IMPORTANT INFORMATION Special blade bolt is heat treated Replace with a Husqvarna bolt if required Do not use lower grade hardware than specified 8050 802 1 Blade 2 Center hole 3 Cutter housing 4 Blade bolt 5 Lockwasher Blade attachment 44 DIXON MAINTENANCE Mower Deck WARNING Before performing any service or adjustment check the following list Engage the parking brake Place the blade switch in the disengaged position Turn ignition switch to OFF position and remove the key Make sure the blades and all moving parts have completely stopped Disconnect the spark plug wire from all spark plugs and place the wire where it cannot come in contact with the plug Adjusting Mower Deck Check the tire pressure before adjustment of the mower deck See Checking Tire Pressure in Maintenance section Faulty mower deck adjustments will cause an uneven mowing result WARNING Blades are sharp Protect your hands with gloves and or wrap blades with a heavy cloth when handling Leveling Mower Deck Adjust the deck while the mower is on a level surface Make sure the tires are inflated to the correct pressure See Technical Data under Transmission If
63. system is equipped with a spark arrester meeting applicable local or state laws if any If a spark arrester is used it should be maintained in effective working order by the operator CONTROLS This operator s manual describes the Dixon Zero Turn Rider The rider is fitted with either a Briggs amp Stratton or Kohler four stroke overhead valve engine developing 16 22 horse power Transmission from the engine is made via two belt driven hydraulic pumps which in turn drive a hydraulic motor for each drive wheel Using the left and right steering controls the flow is regulated and thereby the direction and speed 1 Motion Control Levers 7 Throttle 2 Seat Adjustment Lever 8 Blade Switch 3 Bypass Linkage 9 Circuit Breaker 4 Fuel Tank 10 Parking Brake 5 Ignition Switch 11 Lift Lever 6 Choke Control DIXON 17 CONTROLS Motion Control Levers The machine s speed and direction are continuously variable using the two steering controls The steering controls can be moved forward or backward about a neutral position Furthermore there is a neutral position which is locked if the steering controls are moved outward When both controls are in the neutral position N the machine stands still By moving both controls an equal amount forward or backward the machine moves in a straight line forward or backward respectively In order for example to turn right while movin
64. ters Spark plugs gap NGK BPR4ES NGK BPR4ES 030 0 75 mm 030 0 75 mm a A As rated by the engine manufacturer 60 DIXON TECHNICAL DATA p ZTR36 968999609 ZTR44 968909611 DE AAA AAA ETEA CI wes AAA AAA DT AAA AAA DIXON 61 TECHNICAL DATA poz TR ARI 968999689 ZTR4Z 968999713 ES S O Oil capacity excluding filter 1 875 qts 1 8 liters Oil capacity including filter 1 5 qt 1 42 liters 2 qt 1 91 liters Engine oil Synthetic SAE 5W30 10W30 SAE 5W30 10W30 Engine oil Mineral Class SAE 30 winter 10W30 SAE 30 winter 10W30 API SF SJ SH SG API SF SJ SH SG Fuel Min 86 octane unleaded Max Min 86 octane unleaded Max methanol 10 max MTBE 15 methanol 10 max MTBE 15 Fuel tank capacity 4 5 gallon 17 liters 4 5 gallon 17 liters Spark plugs gap NGK BPR4ES NGK BPR4ES 030 0 75 mm 030 0 75 mm DD As rated by the engine manufacturer 62 DIXON TECHNICAL DATA pz TR AZ 968999689 ZTR42 968999713 C AAA AAA ETEA CS ES EET E DT AAA AAA ES AAA DIXON 63 TECHNICAL DATA po TR 441968999547 CS ES Manufacturer Type ELS Oil capacity excluding filter Oil capacity including filter 2 qt 1 91 liters Engine oil Synthetic SAE 5W30 10W30 Engine oil Mineral Class SAE 30 winter 10W30 API SF SJ SH SG Fuel Min 86 octane unleaded Max methanol 10 max MTBE 15 Fuel tank capacity 4 5 gallon 17 liters Spark plugs gap NGK
65. tey tas aasaga 43 Blades icenean enea aaan paN aE ala 44 Mower Deck sinus titetaiiens 45 Adjusting Mower Deck mu 45 Leveling Mower DeCk ccscceeeseetteeeeeeenees 45 Caster Wheels nnnnaneeeeennenenennene 46 A LAWAFG 1444 maimik Saada maana deal kd 46 Cleaning miiiereeennnnnenannnnaenaannnnananana 46 Tracking Adjustment 47 EZT Transaxle cccccccccceccecececceeeeeeeeeeeeeenseeaeaea 47 Purging Procedure j iiccccccvsicreceeiccceetieene 47 Anti scalp Rollers 2 eccccceeeeeeeeeeeseeseaeees 47 Lubrication Schedule esiisa sian 48 General E A A 48 LUBRICATION cennete arana 48 Lubricating the Cables 49 Following the Lubrication Schedule 49 ON LOVE llc oct tea aknad tiined kala kak kuhi JAG 51 ON Fin aisneis aaa 51 TROUBLE SHOOTING mmmmemeemeeneeeenene 52 STORAGE vasso soane tetes laata idaga 55 Winter Storage mmmuneeennaennnnnenana 55 SOVICE cici mat mis alaku ku Saka ssa 55 SCHEMATIC 2 cecceceeeeeeeeeeeeeeeneeeeeeeeeeeeeeteeeeeea 56 TECHNICAL DATA sicssctarssissteenecsiadi secessie apia 57 Accessories 000 0 cece cee eeceeeeceeececeeeeeteeeeeeeeeeennaneaeess 57 Torque Specifications nnise 57 CONFORMITY CERTIFICATES 66 USA Regui MENiS siessen aaan 66 SERVICE JOURNAL nemmeemeeveenenennene 67 Delivery Service weietet ices

Dixon 44, 44, 44, 36, 36, 42, 42 Lawn Mower User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents