Directed Electronics 732T Automobile Alarm User Manual
Contents
1. Code Hopping 2 2 eae ne edie RE nn ec Sere 13 Programming Options 14 Glossary Of Terms 16 Security amp Convenience Expansions 18 Quick Reference Guide Removable 21 2000 Directed Electronics Inc 1 Standard Configuration Arm Disarm Panic Silent Mode Trunk Release Remote Valet Auxiliary Output 2000 Directed Electronics Inc What is Included The control unit A pair of two button transmitters A Stinger DoubleGuard shock sensor on board the control unit The Revenger Soft Chirp six tone programmable siren The red Status LED indicator light push button Valet switch Your warranty card FailSafe starter kill ready circuitry may require additional parts and labor Important Information Congratulations on the purchase of your state of the art vehicle security system This system has been designed to provide years of trouble free operation This guide should help you to get the most out of your system Please take the time to read it thoroughly prior to using your system Your Warranty gt Your warranty card must be returned If it is not returned you do not have a warranty It is also necessary to keep your receipt which reflects that the product was installed by an authorized dealer Make sure you receive the warranty card from2. It is also used to report trig gers and faults in the system or sensors Shock Sensor This system is packaged with a Double Guard Shock Sensor This sensor is contained within the control unit and designed to pick up impacts to the vehicle or glass Siren Noise generating device usually installed in the engine compartment of the vehicle It is responsible for generating the 16 2000 Directed Electronics Inc chirps you hear as well as the six tones you hear while the alarm is triggered Transmitter Hand held remote control which operates the vari ous functions of your system Trigger or triggered response This is what happens when the alarm goes off or trips The triggered response of your system consists of 30 seconds of siren sounding and parking light flashing Valet Switch A small push button switch mounted somewhere inside the vehicle It is used to override the alarm when a trans mitter is lost or damaged or to put it into valet mode Warn Away response Lighter impacts to the vehicle will gener ate the Warn Away response It consists of several seconds of siren chirps and parking light flashes Zone A zone is a separate input that the alarm can recognize as unique Each input to the system is connected to a particular zone Often two or more inputs may share the same zone 2000 Directed Electronics Inc 17 Security amp Convenience Expansions Here we have listed only some of
3. and the parking lights will flash twice If power locks are controlled by the system the doors will unlock If the siren chirps either four or five times when disarming see Diagnostics section This is called Tamper Alert High Security Disarm Your system includes a High Security Disarm feature During the triggered sequence using the transmitter to disarm it will only stop the triggered sequence the siren will stop and the parking lights will stop flashing however the system will remain armed and the doors will stay locked This is extremely useful if you must stop the system from sounding but are unable to check the vehicle visually The trigger will stop but the vehicle will remain protected To disarm with the transmitter during a trigger press 0 on your transmitter The siren will stop sounding Next press 0 once more and the system will chirp four or five times reporting the trigger and disarm 2000 Directed Electronics Inc 7 Disarming Without a Transmitter This feature allows you to disarm the system without the trans mitter should it be lost damaged or disabled In order to disarm without a transmitter you must have the vehicle s ignition key and know where the Valet switch is located Be sure to check with the installer for the location of the Valet button Turn on the ignition Press the Valet switch within 15 seconds _2 The system should now disarm D If it does not you may have
4. the confirmation chirp s will be eliminated for that one operation only Panic Mode M Press 0 for 1 5 seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for 30 seconds To enter or exit Valet Mode with the Valet switch M Turn ignition to run position then turn to off position Press and release the Valet switch within 10 seconds The Status LED will light steady if you have entered Valet Mode and it will go out if you exited Valet Mode M Open any door Press Press 00 Press again The Status LED will light steady if you have entered Valet Mode and it will go out if you exit ed Valet Mode Using Remote Valet as o enter or exit the vehicle 2000 Directed Electronics Inc 21 The company behind this system is Directed Electronics Inc Since its inception DET has had one purpose to provide consumers with the finest vehicle security and car stereo products and accessories available The recipient of more than 20 patents in the field of advanced electronic technology DEI is ISO 9001 registered Quality Directed Electronics products are sold and serviced throughout North America and around the world Call 800 274 0200 for more information about our products and services O O S 40 1 DEI is an ISO 9001 registered company DEI is committed to delivering on time the best products we know how to provide and to constantly work with our customers and vendors to i
5. understandings whether written or oral IN ANY EVENT DEI IS NOT LIABLE FOR THE THEFT OF THE VEHICLE AND OR ITS CONTENTS This warranty is void if the product has been damaged by accident unreasonable use neglect improper service or other causes not arising out of defects in materials or construction This warranty is nontransferable and does not apply to any unit that has been modified or used in a manner contrary to its intended purpose and does not cover batteries The unit in question must be returned to the manufacturer postage prepaid This warranty does not cover labor costs for the removal diagnosis trou bleshooting or reinstallation of the unit For service on an out of warranty product a flat rate fee by model is charged Contact your authorized dealer to obtain the ser vice charge for your unit These systems are a deterrent against possible theft Directed Electronics Inc is not offering a guarantee or insuring against the theft of the automobile or its contents and disclaims any liability for the theft of the vehicle and or its contents Directed Electronics does not authorize any person to create for it any other obligation or lia bility in connection with this security system 2000 Directed Electronics Inc i TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WARRANTIES ARE EXCLUD ED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COM MERCE THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO
6. your dealer 2000 Directed Electronics Inc 3 System Maintenance The system requires no specific maintenance Your remote is pow ered by a miniature 12V battery type GP23A that will last approx imately one year under normal use When the battery weakens operating range will be reduced and the LED on the remote will dim Transmitter Functions The receiver uses a computer based Learn Routine to learn the trans mitter buttons This makes it possible to assign any transmitter button to any receiver function The transmitter initially comes pro grammed with Standard Configuration but may also be customized by an authorized dealer The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter Standard Configuration Configuration 0 Button The arm disarm and Panic Functions are usually controlled by Button I Button The Silent Mode trunk release and Remote Valet functions are usu ally controlled by Button IT Silent Mode and Remote Valet work by pressing Button IT for less than one second Trunk release requires you to press Button II for 1 5 Seconds 4 2000 Directed Electronics Inc 0 and Button An optional auxiliary convenience or expansion function that you have added to your system can usually be controlled by pressing 0 and simultaneously These button assignments can be changed if needed such as for two car operation from one remote The auxiliary o
7. Model 732T Owner s Guide Limited Lifetime Consumer Warranty For a period of one calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model free of cost any electronic control module which proves to be defective in workmanship or material under normal use SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PROFESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page After the first calendar year from the date of purchase of this auto security device Directed Electronics Inc promises to the ORIGINAL PURCHASER to repair or replace with a comparable reconditioned model any electronic control module which proves to be defective in workmanship or material under normal use FOR A CHARGE OF 45 00 SO LONG AS THE SYSTEM WAS SOLD INSTALLED AND SERVICED BY A PRO FESSIONAL AUTO INSTALLER AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED If warranty service is necessary you must have a clear copy of your sales receipt containing all of the information shown on the following page This warranty contains the entire agreement relating to warranty and supersedes all previous and contemporaneous representations or
8. THE EXCLU SION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WAR RANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR ANY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF AMERICA AND OR ABROAD NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES TOWING REPAIR REPLACEMENT DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE NOTWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state IMPORTANT NOTE This product warranty is automatically void if its date code or serial number is defaced missing or altered This warranty will not be valid unless you have com pleted the warranty card and mailed it to Directed Electronics Inc within 10 days after purchase to the address listed on the warranty registration card Make sure you have all of the following information from your dealer A clear copy of the sales receipt showing the following Date of purchase Your full name and address Autho
9. alled an algorithm to change their code each time the transmit ter is used This technology has been developed to increase the security of the unit The control unit knows what the next codes should be This helps to keep the transmitter in synch with the control unit even if you use the remote control out of range of the vehicle However if the transmitter has been pressed many times out of range of the vehicle or the battery has been removed it may get out of synch with the control unit and fail to operate the system To re synch the remote control simply press the arm dis arm button of the remote control several times within range of the vehicle The alarm will automatically re synch and respond to the transmitters normally 2000 Directed Electronics Inc 13 Programming Options Programming options control what your system does during nor mal operation and require little or no additional parts However some may require additional installation labor The factory set tings are in bold 14 Active arming only with the transmitter or passive arming automatic arming 30 seconds after the last door is closed Arming disarming confirmation chirps on or off Passive door locking with passive arming or active door locking only when arming with the transmitter This feature only works if passive arming has been selected for step one The ignition switch controlled door locking feature on or off With this feature o
10. ar has interior light exit delay and you arm the system before the interior light goes out you may get Bypass Notification Once the light goes out howev er the doors are monitored normally 2000 Directed Electronics Inc 11 Disarming Diagnostics Extra disarm chirps are the Tamper Alert If four chirps are heard when disarming the system was triggered in your absence If five chirps are heard a zone was triggered so many times that Nuisance Prevention Circuitry has bypassed that zone In either case the Status LED will indicate which zone was involved see Table of Zones section The system will retain this information in its memory and chirp four or five times each time it is disarmed until the next time the ignition key is turned on Table of Zones The zone number is the number of LED flashes used by the system to identify that input The standard input assignments are listed below along with spaces to write in any optional sensors or switches you have had installed ZONE Number of DEALER INSTALLED LED Flashes DESCRIPTION OPTIONS 2 Instant trigger a heavier impact detected by the Double Guard Shock Sensor 3 Door switch trigger 4 Optional hood or trunk pins or optional sensors 5 Ignition trigger NOTE If the Warn Away response is triggered the LED will not report it 12 2000 Directed Electronics Inc Code Hopping The receiver and transmitters each use a mathematical formula c
11. ate in convenience the Valet Start System can start your vehicle monitor engine functions and power your climate control system with a push of a button Over rev protection open hood lockout brake pedal shutdown and automatic timer shutdown are all included Only for automatic transmission fuel injected gasoline vehicles Power Window Control Automatic power window control is pro vided with the 529T or 530T systems 2000 Directed Electronics Inc 19 20 Notes 2000 Directed Electronics Inc gt e Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet 2 lt QUICK REFERENCE GUIDE Arming M Press 0 for one second When the system arms you will hear a short chirp and see the parking lights flash once If the vehicle s power door locks are controlled by the system the doors will lock Arming while driving M Press while the vehicle is running The system will chirp once and then once more to indicate that the ignition is on Disarming M Press 0 You will hear two chirps and the parking lights will flash twice If power locks are controlled by the system the doors will unlock Disarming without a transmitter M Turn on the ignition Push the Valet switch within 15 seconds The sys tem should now disarm If it does not you may have waited too long so turn the ignition off and on and try again Silent Mode M Press briefly before arming or disarming and
12. e entry point that has been left open and anything connected to the same zone is bypassed and cannot trigger the system The remaining inputs to the system are fully operational M Siren tones and chirp volume The output of the Revenger Soft Chirp siren consists of six different tones in sequence Any of these tones can be eliminated by your dealer result ing in a unique easily identifiable siren sound The siren chirps can be either full volume or 6 decibels quieter than the full alarm blast 2000 Directed Electronics Inc 15 Glossary of Terms Control Unit The brain of your system Usually hidden under neath the dash area of the vehicle It houses the microprocessor which monitors your vehicle and controls all of the alarms func tions FailSafe Starter Kill optional An automatic switch controlled by the security system which prevents the vehicle s starter from cranking whenever the system is armed The vehicle is never pre vented from cranking when the system is disarmed in valet mode or should the starter kill switch itself fail Your system is ready for this feature however installation of this feature may require addi tional labor Input A physical connection to the system An input can be pro vided by a sensor pinswitch or to existing systems in the vehicle such as ignition or courtesy lights LED Red light mounted somewhere in the vehicle It is used to indicate the status of your system
13. ently If the alarm is triggered by an open door for three full cycles one and one half minutes the doors will be bypassed until the trigger ceases 10 2000 Directed Electronics Inc NOTE Arming and disarming the system does not reset this function The only ways to reset a bypassed zone are for it to remain untriggered for 60 minutes or to turn on the ignition If testing your system it is important to remember that the NPC programming can cause zones to be bypassed and seem to stop working If five chirps are heard when disarming NPC has been engaged If you wish to clear the NPC memo ry turn the ignition on Diagnostics The microprocessor at the heart of your system is constantly mon itoring all of the switches and sensors connected to it It detects any faulty switches and sensors and prevents them from disabling the entire system The microprocessor will also record and report any triggers that occurred during your absence Arming Diagnostics Diagnostics If the system is armed with an input active door open sensor triggering etc the unit will chirp once when arming and then one more time a few seconds later This is called Bypass Notification NOTE Bypass notification will not occur when using Silent Mode or if chirps have been programmed OFF The system will ignore the input that was active when it was armed until it goes away Three seconds later it will monitor that input normally For example if your c
14. mprove our products qual ity delivery and customer friendly features pEr PAN Directed Electronics Inc Vista CA 92083 www directed com 2000 Directed Electronics Inc All rights reserved G732T 4 00
15. n the doors will lock 3 seconds after the key is turned on and unlock when the key is turned off NOTE If the door is open when the ignition is turned on the doors will not lock Panic mode enabled disabled with the ignition on Some states have laws against siren capability in a moving vehicle Automatic Engine Disable AED on or off This feature deters theft of the vehicle whether or not the alarm is armed If AED is programmed on the starter of the vehicle will be dis abled 30 seconds after the ignition is turned off The LED will flash slowly one half its normal armed rate to indicate the AED arming cycle 30 seconds later the starter of the vehicle will be disabled To start the car you will need to arm the car 2000 Directed Electronics Inc with the remote and then disarm it with the remote You can also disarm the AED feature by turning the ignition on and pressing the valet button once AED is also disabled when in valet mode NOTE This feature will only function if the FailSafe starter kill relay has been installed M Forced passive arming on or off If your system is pro grammed to passively arm and this feature has been pro grammed on the system will passively arm after one hour even if a protected entry has been left open If a door has accidentally been left ajar when leaving the vehicle forced passive arming ensures that the system will arm in one hour NOTE When forced passive arming occurs th
16. n on 2 Turn the ignition off 3 Press and release the Valet switch within 10 seconds DRASS The status LED will light solidly if you are entering Valet Mode and it will go out if you are exiting Valet Mode 2000 Directed Electronics Inc 9 Remote Valet Valet You can also activate Valet Mode using the remote transmitter 1 Open any vehicle door 2 Press 0 or the arm disarm button 3 Press or the channel 2 button 4 Press 0 again The status LED will light solid if you are entering Valet Mode or will go out if you are exiting Valet Mode Nuisance Prevention Circuitry NPC Your system has Nuisance Prevention Circuitry to prevent annoying repetitive trigger sequences due to faulty door pin switches or envi ronmental conditions such as thunder jackhammers or airport noise Here s how it works Let s say the alarm triggers three times Each time the same sensor or switch is triggering the alarm The three triggers are within 60 minutes of each other NPC will interpret this pattern of triggers as false alarms After the third trigger NPC ignores or bypasses that sensor or switch along with any other sensors or switches sharing the same zone If the bypassed sensor tries to trigger the system while it is being bypassed the 60 minute bypass period will start over This ensures that a sensor that continuously triggers will remain bypassed Doors are covered by NPC differ
17. ng ways Light impacts will trigger the Warn Away signal When trig gered the siren will chirp and the parking lights will flash for a few seconds Heavy impacts will trigger the system The trigger sequence is 30 seconds of constant siren and flashing parking lights If a door is opened the system will immediately start chirp ing the siren and flashing the parking lights Three seconds later the siren output changes to a continuous blast This progressive response gives you time to disarm the system with your transmitter if you inadvertently open the door while the system is armed while still providing instant response even if the door is immediately closed Turning on the ignition key will trip the same two stage response as opening a door The optional starter kill prevents the starter from cranking Arming While Driving While Driving Your system can be armed while driving the vehicle Simply press 0 on your transmitter while the vehicle is running The system will chirp once and then once more to indicate that the ignition 6 2000 Directed Electronics Inc is on The system will not respond to any input except the door triggers and the starter kill relay if installed will not be activated The system will disarm automatically when the ignition is turned off The siren will chirp twice and the LED will stop flashing CE gt To turn off or disarm the system press 0 again You will hear two chirps
18. rized dealer s company name and address Type of system installed Year make model and color of the automobile Automobile license number Vehicle identification number All security options installed on automobile Installation receipts ii 2000 Directed Electronics Inc Table of Contents Limited Lifetime Consumer Warranty i What Is Included 2 72 48 en a nor tie Kiana ae ae Us 3 Important Information 3 Your Warrior o i 3 System Maintenance 4 Transmitter Functions 4 Standard Configuration 5 58 ut wie sin mien AR Ets dos 4 Using your System oia sis gig Oe lanl sl eee he a eh 5 Arming S tn ha te tae Se Sn A Eire mettent th s tr dard 5 Arming While Diving esset aa a dns Se ee nn ete 6 DISARMING ii at A eel LE Rd See au ee S 7 High Security Disarm r eces o a eat line en a tue 7 Disarming Without A Transmitter 8 Silent Mode esn ee sets aa arts 8 Panic Modes faa te Sa is a Mee Da Ne ae Mere te 9 Valet Mode A aa 9 Remote Valet o comida e AAA nt er 10 Nuisance Prevention Circuitry 10 Diagnostics ein iii ceed at cis A dose a are 11 Arming Diagnostics a ev a eo ke ale ee ea haw Rl a three Gla 11 Disarming Diagnostics 12 Table of Zones ieii stot sk a ne ae a abe eue 12
19. the many expansion options available Please consult your dealer for a complete explanation of all the options available to you Field Disturbance Sensor An invisible dome of coverage is established by the 508T radar sensor Your system can react to any intrusions into this field with the triggered sequence Backup Battery The 520T keeps the system armed triggers the alarm and keeps the starter kill active if main battery power is dis connected Electronic Hood Lock This prevents the vehicle s hood from being opened whenever the system is in alarm mode keeping thieves away from the system s siren the battery connections or other components under the hood Audio Sensor Metal on glass glass cracking or breaking glass produce distinctive acoustic signatures The 506T audio sensor uses a microphone to pick up sounds and then analyze them with pro prietary acoustic software to determine if the glass has been struck Power Trunk Release One of the auxiliary outputs of the system can operate a factory power release for the vehicle s trunk or hatch An optional relay may be required If the factory release is not power activated DEI s 522T trunk release solenoid can often be added 18 2000 Directed Electronics Inc Power Locks This system offers lock outputs that can control some manufacturers power door lock systems For other systems additional parts may be required Valet Start System For the ultim
20. utput controls Using Your System ETD II You can turn on or arm the system by pressing 0 of your trans mitter for one second When the system arms you will hear a short siren sound or chirp and see the parking lights flash once If the vehicle s power door locks are controlled by the system the doors will lock While the system is armed the Status LED will flash about twice a second showing that the system is actively pro tecting your vehicle If you hear a second chirp after arming and see the Status LED flashes in groups see Diagnostics section This extra chirp is called Bypass Notification The system also can be programmed to arm itself automatically called passive arming If the system is programmed for passive arming it will automatically arm 30 seconds after the ignition is turned off and the system sees you leave the vehicle by opening and closing a door Whenever the system is in its 30 second passive arming count 2000 Directed Electronics Inc 5 down the Status LED will flash twice as fast as it does when the system is armed NOTE If any protected entry point such as a door or a switch protect ed trunk or hood is open the system will not passively arm unless forced passive arming is programmed on See Programming Options sec tion Additionally each time a sensor is triggered during the arming countdown the 30 second countdown starts over When armed your vehicle is protected in the followi
21. waited too long to press the Valet switch so turn the igni tion off and on and try again To temporarily turn off the arm or disarm chirps use Silent Mode Simply press briefly before arming or disarming and the con firmation chirp s will be eliminated for that one operation only If you want the arm disarm chirps turned off permanently your dealer can do this for you NOTE The Warn Away response to lighter impacts is bypassed if the sys tem is armed using Silent Mode This ensures that no chirps will be emit ted by the siren in an area you want chirp free The system is still fully able to trigger Only the Warn Away response is defeated 8 2000 Directed Electronics Inc Panic Mode Mode If you are threatened in or near your vehicle you can attract attention by triggering the system with your transmitter Just press 0 for 1 5 seconds and you will enter Panic Mode The siren will sound and the parking lights will flash for 30 seconds To stop Panic Mode at any time press 0 on the remote transmitter again Valet Mode You can prevent your system from automatically arming and trig gering by using Valet Mode This is very useful when washing the vehicle or having it serviced In Valet Mode the system will not arm even with the transmitter but all convenience functions door locks trunk release etc will work normally To enter or exit Valet Mode with the Valet switch 1 Turn the ignitio
Download Pdf Manuals
Related Search