Dimplex BLF50 Indoor Fireplace User Manual
Contents
1. Wall surface Mounting hole Front glass assembly mounting screws through the four 4 mounting holes located on the inside surface of the fireplace chassis into wall studs Figure 14 Refer to Front Glass Installation section page 16 for final installation procedures Front Glass Installation Evenly distribute supplied glass rock on the front tray of the fireplace Figure 15 Carefully mount front glass assembly so that the front glass hooks 4 hang on the front glass mounts on the Figure 1 Front tray www dimplex com Fireplace Installation fireplace 4 Figure 16 Figure 16 Use the supplied two 2 Mounts 4 Phillips sheet metal screws Hooks 4 to fasten the glass assembly A tabs to the fireplace Figure IS WA 17 Ty x Ensure the fireplace s On Off Switch is switched to the Off position refer to operation section If unit is not hard wired plug fireplace into a 15 Amp 120 Volt outlet refer to NOTE 1 Figure 17 Tab 17 Operation The manual controls for the electric fireplace are located on the right side of the unit and inside the air intake slot Figure 18 Figure 18 A On Off Switch The On Off Switch supplies power to all fireplace functions When the switch is in the I position the2. 50 6 128cm x 19 49 5cm e Unit requires a minimum of two 2 wall studs in order to ensure a secure installation Three possible installation methods e Installation method Surface mount pg 12 In wall Recessed pg 13 or Flush mount pg 15 e Hardwired or plug in method NOTE 1 A 15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essential in all cases A dedicated circuit will be required if after installation the circuit breaker trips or fuse blows on a regular basis when the heater is operating Additional appliances on the same circuit may exceed the current rating of the circuit breaker La WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electric shock and injury to persons Select a location that is not susceptible to moisture and is away from drapes furniture and high traffic For ease of electrical hook up you may wish to locate the fireplace near an existing outlet for plug in convenience refer to NOTE 1 Remove fireplace front glass and hardware from box and remove all packaging materials before installation
3. Phillips screws that fasten the media tray and two 2 screws that fasten the front panel tabs Figure 3 Carefully remove both components 3 Remove one 1 Phillips screw to release the electrical box cover in the bottom right corner of the fireplace Figure 9 Fireplace Installation Front Panel Front Panel tabs 2 lt Figure 4 Electrical box Figure 5 Wires to Junction controls Box screw Wire connectors Figure 6 Screw 4 4 Carefully remove the electrical box cover from the fireplace as wires are fed Junction Box screws 3 through the strain reliefs on the cover and are connected screw that attaches the within junction box cover to the 5 Unscrew the two 2 wire pesto cai Figure connectors inside the i electrical box and separate 7 From the back of the the wires Figure 5 fireplace H aa 6 Remove the one 1 Phillips A 10 www dimplex com Fireplace Installation screws which hold the junction box to the fireplace chassis Figure 6 Pull the junction box and power cord out the front of the fireplace Replace removed junction box cover with the supplied hard wire cover replacement Figure 7 and install using screws removed in steps 6 Figure 7 10 11 12 Hole for Ground Screw and 7 Leaving a minimum of 3 7 6 cm of slack route the power supply through the hole in the alternate junction box cover
4. holes and fireplace will Permanent 3 slide down into place screws mounting hole will slide into narrow part of key holes 10 Tighten all four 4 mounting screws down on fireplace chassis 11 Screw the two 2 supplied F8 square head screws through two of the permanent mounting holes which align the wall through key holes with a wall stud 6 Remove fireplace from wall 12 Carefully replace and install and store in a safe place partially reflective glass and away from traffic glass brackets using screws 7 Where marked screw from step 1 locations do not line up with 13 Refer to Front Glass a wall stud insert screw in Installation section page one 1 of the two 2 supplied 16 for final installation wall anchors predrill if procedures required Repeat if only two 2 screws line up with a wall In wall Recessed stud Installation 2x4 Framing 8 Screw all four 4 supplied A ee CAUTION Two people may 49 TA inch 3 0 em square be required for various steps head mounting screws and f thi d washers into the wall and or Or TAIS procecure wall anchors leaving 1 4 inch 1 Prepare a wall with a framed 6 5 mm of thread opening of 4672 118 1 cm wide x 16 42 cm high 9 Align chosen key holes with screws and hang fireplace Figure 10 13 S Fireplace Installation Figure 10
5. range of approximately 50 feet 15 25 m it does not have to be pointed at the fireplace and can pass through most obstacles including walls It is supplied with one of hundreds of independent frequencies to prevent interference with other units NOTE Before attempting any operation with the remote pull the plastic insulator strip out from between the remote casing and battery cover Figure 19 Remote Control Initialization Reprogramming If the remote control or remote control receiver has been replaced follow these steps to initialize the remote control and receiver 1 Ensure that power is supplied through the main service panel 2 Turn On Off Switch to On Figure 18A 3 Move the 3 Position Switch to the REMOTE position Figure 18B Figure 19 On Button Off Button Plastic strip Battery cover 4 Press and hold the Manual Control Button marked I for five 5 seconds After five 5 seconds there is a 10 second window to press any button on the remote control 5 Press any button on the remote control within that 10 seconds This will synchronize the remote control and receiver Remote Control Usage The remote control operates the fireplace levels sequentially from off flames only to flames and low heat to flames and high heat The level is increased every time the ON button is pressed on the remote control and the fir
6. NING Procedures and techniques which if not carefully followed will expose the user to the risk of fire serious injury or death 2 www dimplex com Welcome 8 Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex the world leader in electric fireplaces Please carefully read and save these instructions amp CAUTION Read all instructions and warnings carefully before starting installation Failure to follow these instructions may result in a possible electric shock fire hazard and will void the warranty Please record your model and serial numbers below for future reference model and serial numbers can be found on the Model and Serial Number Label of your fireplace SS gt WWA Serial Number Label STOP NO NEED TO RETURN TO THE STORE Questions with operation or assembly Require Parts Information Product Under Manufacturer s Warranty ating Label Contact us at www dimplex com customer_support For Troubleshooting and Technical Support sa OR 4 Toll Free 1 888 DIMPLEX 1 888 346 7539 Monday to Friday 8 00 a m to 4 30 p m EST Please have your model number and product serial number ready Se
7. NOTE The sizing has allowed for 1 4 6 4mm around the fireplace insert for ease of installation This fireplace does not require any additional venting 2 Choose your method of supplying power to the unit e Plug in you may run the power cord out of the framed wall opening to an existing outlet or install an outlet on a nearby wall stud within the wall e Hard wire the fireplace recommended Follow the hard wiring instructions on page 9 WARNING Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician Ensure that the On Off Switch is set to the Off position refer to Operation section and that the circuit on which the fireplace is to be installed has the power cut off at Figure 11 Mounting holes the service panel until installation is complete 3 Lift fireplace and insert into opening Figure 11 4 Use bubble level supplied to level the fireplace within the framing Adjust as required 5 Drive four 4 supplied mounting screws through 14 www dimplex com Fireplace Installation Figure 12 Mounting hole the four 4 mounting holes located in each corner of the fireplace chassis into wall studs Figure 12 6 Refer to Front Glass Installation section page 16 for final installation
8. Store the fireplace in a safe dry and dust free location until you are ready to install the fireplace www dimplex com Fireplace Installation Hardwire Installation The fireplace is packaged with a two prong plug installed for plug in convenience Hard wiring the fireplace is also an option for any installation amp WARNING Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician WARNING Ensure that the On Off Switch is set to the Off position refer to Operation section and that the circuit on which the fireplace is to be installed has the power cut off at the service panel until installation is complete 1 Remove the partially reflective glass from the fireplace e Lay fireplace on its back e Remove two 2 Phillips screws from each of the two 2 glass brackets Figure 2 e Remove glass brackets e With one hand keeping pressure on the partially reflective glass tilt the fireplace upright and slightly Figure 2 g Bracket Screws Partially Reflective Glass H Glass Bracket forward to allow the partially reflective glass to fall out of the inside framing amp CAUTION Partially reflective glass is not tempered Do not bump or drop the partially reflective glass to avoid breakage and personal injury e Remove partially reflective glass from fireplace 2 Remove six 6
9. X Dimplex Better solutions through innovation os 1 X Owner s Manual Model BLF50 IMPORTANT SAFETY INFORMATION Always read this manual first before attempting to install or use this fireplace For your safety always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage To view the full line of Dimplex products please visit www dimplex com 7210380100R02 Table of Contents O Welcome 8 Congratulations 3 AQ IMPORTANT INSTRUCTIONS ooo ooo coco ooo 4 Quick Reference Guide oooocoooccooooo 7 SK Fireplace Installation ec ara 8 Site SelectiON i a asiaa ia acata aia ea ees 8 Hardwire Installation aana aaua aaa 9 Surface Installation 000 0000 eee 12 In wall Recessed Installation 2x4 Framing 13 Flush Mounted Installation 2x8 Framing 15 Front Glass Installation o ooo oooooocooooooo 16 O7 One Alon cp sehen ded oud eee do 18 I Maintenance ooo 20 Waranty oie pis ene Bt eee ee a oe 21 oe Accessories 1 es 23 Replacement Parts 00000 0c eee ees 24 Always use a qualified technician or NOTE Procedures and service agency to repair this fireplace techniques that are considered important enough to emphasize A CAUTION Procedures and techniques which if not carefully followed will result in damage to the equipment aA WAR
10. and secure with a wire clamp not supplied Connect the black wire live from the unit to the black wire from the power supply using one of the wire connectors removed in step 5 Figure 8 Connect the white wire neutral from the unit to the Figure 8 Wires to Black live controls wires e a MA NN 7 7 White neutral wires 13 14 white wire from the power supply using the second wire connector from step 5 Figure 8 Attach green grounding wire to hard wire cover cover with provided grounding screw Place wire in between screw and lock washer and tighten Reposition the electrical box cover over the wires and connectors and attach to fireplace chassis using the screw removed in step 3 Carefully reinsert partially reflective glass into fireplace and anchor in place using glass brackets and screws removed in step 1 Fireplace Installation 16 Refer to Front Glass Installation section page 16 for final installation procedures Surface Installation amp CAUTION Two people may be required for various steps of this procedure 1 Choose a location which has a minimum of two 2 wall studs available for mounting 2 Choose your method of supplying power to the unit e Plug in to an existing outlet or install an outlet nearby e Hard wire the fireplace Follow the hard wiring instructions on page 9 WARNING Do not attempt to wire your own new outlets o
11. e above amp IMPORTANT INSTRUCTIONS When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following Q Read all instructions before using the electric fireplace 2 This fireplace is hot when in use To avoid burns do not let bare skin touch hot surfaces The trim around the heater outlet becomes hot during heater operation 3 Extreme caution is necessary when any heater is used by or near children or invalids and whenever the unit is left operating and unattended 4 Young children should be supervised to ensure that they do not play with the appliance 5 The appliance is not intended for use by young children or infirmed persons without supervision If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a qualified person in order to avoid a hazard 2 Do not operate any unit with a damaged cord or plug or if the heater has malfunctioned or if the electric fireplace has been dropped or damaged in any manner contact Dimplex Technical Service at 1 888 346 7539 Do not use outdoors 9 Never locate fireplace where it may fall into a bathtub or other water container Keep combustible materials such as furniture pillows bedding papers clothes and curtains at least three 3 feet 0 9 m from the front of the unit AD Do not ru
12. eplace can be turned off at any point by pressing the OFF button 19 Operation Battery Replacement To replace the battery 1 Slide battery cover open on the remote control Figure 19 2 Install one 1 12 Volt A23 battery in the battery holder 3 Close the battery cover oe Maintenance La WARNING Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire electric shock or damage to persons Partially Reflective Glass Cleaning The partially reflective glass is cleaned in the factory during the assembly operation During shipment installation handling etc the partially reflective glass may collect dust particles these can be removed by dusting lightly with a clean dry cloth To remove fingerprints or other marks the partially reflective glass can be cleaned with a damp cloth The partially reflective glass Ay Battery must be recycled Ke or disposed of properly Check with your Local Authority or Retailer for recycling advice in your area should be completely dried with a lint free cloth to prevent water spots To prevent scratching do not use abrasive cleaners Fireplace Surface Cleaning Use only a damp cloth to clean painted surfaces of the fireplace Do not use abrasive cleaners Servicing Except for installation and cleaning described in this manual an authorized service representative should perform any other servicing 20 w
13. ing or replacing the product or part except as follows i charges which may be levied for travel costs incurred to travel to the purchaser s site where the product is located if the purchaser s site is beyond 30 miles 48 km from the closest service depot of Dimplex s dealer or service agent and ii the purchaser is solely responsible for providing clear access to all serviceable parts of the product For surrounds mantels and trims this 1 year limited warranty does not entitle the purchaser to on site or in house warranty services The purchaser is responsible for removal and transportation of the surrounds mantels and trims and any repaired or replacement product or part to and from the authorized dealer s or service agent s place of business On site or in home services for surrounds mantels and trims may be performed at the purchaser s specific request and expense at Dimplex s then current rates for such services Dimplex will not be responsible for and this limited warranty shall not include any expense incurred for installation or removal of the surrounds mantels or trims or any part thereof or any replacement product or part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s place of business and all labour costs Such costs shall be the purchaser s responsibility What Dimplex and its dealers and service agen
14. ions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 2 years from the date of the first purchase of such products Dimplex fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment and subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products The limited 2 year warranty period for products other than fireplace surrounds mantels and trims and the limited 1 year warranty period for fireplace surrounds mantels and trims also applies to any implied warranties that may exist under applicable law Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to the purchaser What this limited warranty does not cover This limited warranty does not apply to products that have been repaired except by Dimplex or its authorized service representatives or otherwise altered This limited warranty does further not apply to defects resulting from misuse abuse accident neglect incorrect installation improper maintenance or handling or operation with an incorrect power source What you must do to get service under this limited warranty Defects must be brought to the attention of Dimplex Technical Ser
15. n the cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traffic area and where it will not be tripped over 2 Do not locate the heater immediately below a fixed socket outlet 43 To disconnect the fireplace turn the controls off then remove the plug from the outlet 4 www dimplex com amp IMPORTANT INSTRUCTIONS Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage to the heater 15 Do not block air intake or exhaust in any manner Do not use on soft surfaces like a bed where openings may become blocked All electrical heaters have hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored or where the unit will be exposed to flammable vapors Do not modify the electric fireplace Use it only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Avoid the use of an extension cord Extension cords may overheat and cause a risk of fire If you must use an extension cord the cord shall be No 14 AWG minimum size and rated not less then 1875 Watts Do not burn wood or other materials in the electric fireplace Do not strike the fireplace glass Qi Always use a certified electrician should new circuits or o
16. procedures Flush Mounted Installation 2x8 Framing amp CAUTION Two people may be required for various steps of this procedure 1 Prepare a wall with a framed opening of 49 124 5 cm wide x 18 47 cm high Figure 13 NOTE The sizing has allowed for 1 4 6 4mm around the fireplace insert for ease of Figure 13 2 x 8 Framing installation This fireplace does not require any additional venting 2 Choose your method of supplying power to the unit e Plug in you may run the power cord out of the framed wall opening to an existing outlet or install an outlet on a nearby wall stud within the wall e Hard wire the fireplace recommended Follow the hard wiring instructions on page 9 WARNING Do not attempt to wire your own new outlets or circuits To reduce the risk of fire 15 Fireplace Installation electric shock or injury to persons always use a licensed electrician Ensure that the On Off Switch is set to the Off position refer to Operation section and that the circuit on which the fireplace is to 6 be installed has the power cut off at the service panel until installation is complete 3 Lift fireplace and insert into opening The fireplace s mounting trim should be flush 1 against the wall Figure 14 4 Use bubble level supplied to level the fireplace within the 2 framing Adjust as required 5 Drive four 4 supplied Figure 14 Mounting hole
17. r circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician Ensure that the On Off Switch is set to the Off position refer to Operation section and that the circuit on which the fireplace is to be installed has the power cut off at the service panel until installation is complete 3 Remove the partially reflective glass from the fireplace Lay fireplace on its back Remove two 2 Phillips screws from each of the two 2 glass brackets Figure 2 page 9 e Remove glass brackets e With one hand keeping pressure on the partially reflective glass tilt the fireplace upright and slightly forward to allow the partially reflective glass to fall out of the inside framing amp CAUTION Partially reflective glass is not tempered Do not bump or drop the partially reflective glass to avoid breakage and personal injury e Remove partially reflective glass from fireplace 4 Position the fireplace on a wall at the position where it will be mounted Figure 9 Use a bubble level one is supplied to ensure that fireplace is level on the wall 5 Ensuring that at least two 2 key holes line up with a wall stud key holes are spaced at four 4 inch 10 2 cm centers mark the location of four 4 screw locations on 12 www dimplex com Fireplace Installation Figure 9 on the wall Screw heads Key hole Veal stug and washers will fit through key
18. s shall not apply to this limited warranty or the sale of products covered by this limited warranty 23 oS Replacement Parts Elm Einicio ei hae eS Ge pee a 2200510500RP Partially Reflective Glass 0 2 0 0 0 0 00 cece eee eee 5901920100RP NA eE staan Coe ee De gen eee wen he eee pects 5300260100RP A wen beta dae e eee ede eee heed bee 5901930100RP Power Cord siria A Say wre Bip ee Lao are 8400320100RP Flicker M set tied eae ty ead nea ek dee Lae 2000220100RP Flicker ASSEMBIY sa grasi e osha rt ber de E dee 5901910100RP CUTOUT arar E ae eR eee ae ee TE 2300200100RP LED Light Panel i205 ccsiecceeu ded nia area e 3000830102RP Remote Receiver 0 2 0 000 cece eee 3000820100RP SWItCh Board so ir tas wed aR be ae 3000820300RP LED Driver Board oes ccus ones eee ee daw ee ee RA RE 3000810100RP On OM SWIC vrs eu Gant owen E wee ae 2800070700RP Terminal Block cien e de the de a oe v 4000070100RP Capac uns twee hi wad in bed ee eae had waa 3200030100RP Remote Control 2 0 2 2 0 6000 e eee 3000370900RP Glass Media oia osea ote pip ara gle eee pike So ee 1400070100RP Hardware Kit esc antares penest nee Rabe Glee aang geese 9600350100RP X Dimplex Ous Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 O 2012 Dimplex North America Limited 24 www dimplex com
19. the interference by one or more of the following measures Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected lt Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device www dimplex com Quick Reference Guide The electrical information Figure 1 regarding your electric fireplace can 7 be found on the rating label located 17 8cm 7 on the front of the unit behind the glass Before installation please record your fireplace s serial number below for future reference 16 18 Ifyou have any technical 40 6 cm 45 7 cm questions or concerns regarding the operation of your electric fireplace or require service contact customer service 1 For dimensions of your fireplace 3 1346 refer to Figure 1 9 7 cm 48 13 123 cm j 46 116 cm L 50 546 128 cm j Fireplace Installation Site Selection Review and consider all of the following conditions for installation Dimensions of the unit
20. ts are also not responsible for IN NO EVENT WILL DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING 22 www dimplex com SY Warranty OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL DIMPLEX OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF Accessories Contact your local authorized Dimplex dealer for these and other available accessories for your electric fireplace Wall Switch Remote Control WRCPF KIT Wall mounted remote for flame on off and thermostat INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER How State and Provincial law apply This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sale of Good
21. unit is on When in the O position the fireplace is off B 3 Position Switch The 3 Position Switch changes the mode the fireplace operates in and has three 3 positions MANUAL OFF and REMOTE When in REMOTE mode the fireplace s three levels of operation are controlled by the ON and OFF buttons of the remote control In OFF mode power to all functions is cut off In MANUAL mode the fireplace s three levels of operation are controlled by the Manual Control Buttons C Manual Control Buttons The Manual Control Buttons operate the fireplace levels sequentially from off flames only to flames and low heat to flames and high heat The level is increased every time the I button is pressed and the fireplace can be turned off at any point by pressing the O button Resetting the Temperature Cutoff Switch Should the heater overheat an automatic cut out will turn the fireplace off and it will not come back on without being reset It can be reset by switching the On Off Switch to Off and waiting five 5 minutes before switching the unit back on amp CAUTION If you need to continuously reset the heater disconnect power and call Dimplex customer service at 1 888 DIMPLEX 1 888 346 7539 18 www dimplex com Operation Remote Control The fireplace is supplied with a radio frequency remote control This remote control has a
22. utlets be required Always use properly grounded fused and polarized outlets 3 Disconnect all power supply before performing any cleaning maintenance or relocation of the unit When transporting or storing the unit and cord keep ina dry place free from excessive vibration and store so as to avoid damage CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER SERVICABLE PARTS INSIDE SAVE THESE INSTRUCTIONS amp IMPORTANT INSTRUCTIONS WARNING Remote control contains small batteries Keep away from children If swallowed seek medical attention immediately WARNING Do not install battery backwards charge put in fire or mix with used or other battery types may explode or leak causing injury NOTE Changes or modifications not expressly approved by the party responsible for compliance could void user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct
23. vice by contacting Dimplex at 1 888 DIMPLEX 1 888 346 7539 or 1367 Industrial Road Cambridge Ontario Canada N1R 7G8 Please have proof of purchase catalogue model and serial numbers available when calling Limited warranty 21 SY Warranty service requires a proof of purchase of the product What Dimplex will do in the event of a defect In the event a product or part covered by this limited warranty is proven to be defective in material or workmanship during i the 2 year limited warranty period for products other than fireplace surrounds mantels and trims and ii the 1 year limited warranty period for surrounds mantels and trims you have the following rights e Dimplex will in its sole discretion either repair or replace such defective product or part without charge If Dimplex is unable to repair or replace such product or part or if repair or replacement is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part e Limited warranty service will be performed solely by dealers or service agents of Dimplex authorized to provide limited warranty services For products other than surrounds mantels and trims this 2 year limited warranty entitles the purchaser to on site or in home warranty services Accordingly Dimplex will be responsible for all labour and transportation associated with repair
24. ww dimplex com Y Warranty Products to which this limited warranty applies This limited warranty applies to your newly purchased Dimplex electric fireplace This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory Nunavut or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska This limited warranty applies to the original purchaser of the product only and is not transferable Products excluded from this limited warranty Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner purchaser Products purchased in Yukon Territory Nunavut Northwest Territories Hawaii or Alaska are not covered by this limited warranty Products purchased in these States provinces or territories are sold AS IS without warranty or condition of any kind including without limitation any implied warranties or conditions of merchantability or fitness for a particular purpose and the entire risk of as to the quality and performance of the products is with the purchaser and in the event of a defect the purchaser assumes the entire cost of all necessary servicing or repair What this limited warranty covers and for how long Products other than fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment and subject to the provis
Download Pdf Manuals
Related Search