Delta 36-426 Saw User Manual
Contents
1. n Avy HEN Aw M Bi AMI E aids n iva E ES A Fig 101 Fig 101A Fig 101B ADJUSTING BLADE ALIGNMENT WARNING Blade Alignment is Factory Set and should not need adjustment Adjusting Blade Alignment in the field is a difficult and time consuming procedure All Saw Blades have some run out Therefore re adjusting blade alignment should only be attempted if it becomes necessary See step 6 in CHECKING BLADE ALIGNMENT 1 WARNING Disconnect machine from power source 2 Lower blade Remove blade guard and table insert With a 1 2 wrench loosen the 4 front and rear trunnion mounting bolts E Fig 101C NOTE Only the 2 rear trunnion mounting bolts are shown 3 Move the trunnion assembly in the desired direction i Tap gently with rubber mallet if necessary Fig 101C 4 To check blade alignment follow CHECKING BLADE ALIGNMENT procedure until proper alignment is achieved Tighten 4 trunnion bolts E 5 Check blade alignment again after tightening bolts to confirm alignment If alignment is off loosen the 4 trunnion bolts E and repeat the above steps until proper alignment is achieved with bolts fully tightened 6 Install table insert blade guard and lower blade before reconnecting power source MITER GAGE OPERATION AND ADJUSTMENT 1 Insert the miter gage bar into the miter gage slot and N assemble the washer and lock handle A Fig 102 to the miter gage bar2. 5 Fasten the front table support F Fig 49 to the bottom of the table using two 8 x 3 4 long self tapping wood screws and 1 supplied NOTE The slots closer to the angles in the support F should be against the table and the vertical flange of the table support should be flush with the front edge of the table NOTE Screws and I Fig 49 should not be completely tightened to the table board at this time NOTE Make certain the end of the table support does not extend out past the table NOTE Screw must be removed and reinstalled when table is mounted to the saw CAUTION DO NOT OVER TIGHTEN MOUNTING SCREWS Over tightening screws in particle board may cause them to strip 6 Fasten the rear table support A Fig 50 to the saw table Insert a 3 8 16 x1 hex head screw B through hole in rear support and table place a 3 8 washer onto the screw and thread a 3 8 16 hex nut onto screw and tighten Repeat this process for the remaining hole Hole C is not used on cast iron wing 7 Assemble the three brackets J to the table adapter plate K using the three 1 4 20 x 3 4 carriage bolts nuts and washers Fig 51 NOTE The long leg of the brackets J should be against the adapter plate K Do not completely tighten brackets J to adapter plate K at this time 8 Fasten the table adapter plate B Fig 52 to the right side of the saw table Place a 7 16 lockwasher onto a 7 16 20 x1 hex head scr
3. bw other warranties express or implied whether of merchantability fitness for purpose or otherwise are expressly 9 7 disclaimed by Delta NOTES 50 NOTES 51 PORTER CABLE e DELTA SERVICE CENTERS CENTROS DE SERVICIO DE PORTER CABLE e DELTA Parts and Repair Service for Porter Cable Delta Machinery are Available at These Locations Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter Cable Delta ARIZONA Tempe 85282 Phoenix 2400 West Southern Avenue Suite 105 Phone 602 437 1200 Fax 602 437 2200 CALIFORNIA Ontario 91761 Los Angeles 3949A East Guasti Road Phone 909 390 5555 Fax 909 390 5554 San Leandro 94577 Oakland 3039 Teagarden Street Phone 510 357 9762 Fax 510 357 7939 COLORADO Arvada 80003 Denver 8175 Sheridan Blvd Unit S Phone 303 487 1809 Fax 303 487 1868 FLORIDA ee Davie 33314 Miami 4343 South State Rd 7 441 Unit 107 Phone 954 321 6635 Fax 954 321 6638 Tampa 33609 4538 W Kennedy Boulevard Phone 813 877 9585 Fax 813 289 7948 GEORGIA Forest Park 30297 Atlanta 5442 Frontage Road Suite 112 Phone 404 608 0006 Fax 404 608 1123 ILLINOIS Addison 60101 Chicago 400 South Rohlwing Rd Phone 630 424 8805 Fax 630 424 8895 Woodridge 60517 Chicago 2033 West 75th Street Phone 630 910 9200 Fax 630 910 0360 MAR
4. Insert cap K into top of handle A 2 The miter gage is equipped with adjustable index stops at 90 degrees and 45 degrees right and left Adjustment to the index stops can be made by tightening or loosening the three adjusting screws B Fig 103 3 To rotate the miter gage loosen lock knob A Fig 103 and move the body of the miter gage C to the desired angle 4 The miter gage body will stop at 90 degrees and 45 M oce degrees both right and left To rotate the miter gage body past these points the stop link D Fig 103 must be moved up and out of the way 5 The head of the miter gage pivots on a special tapered screw G that fastens the head to the miter gage bar If the miter gage head does not pivot freely or pivots too freely adjust it by loosening set screw H Fig 104 and turning the screw G in or out Be certain to tighten screw H after adjustment is made ADJUSTING TABLE INSERT ZN warnine DISCONNECT MACHINE FROM POWER SOURCE Place a straight edge across the table at both ends of the table insert Fig 105 The table insert A should always be level with the table If an adjustment is necessary turn the adjusting screws B Four adjusting screws B are supplied in the table insert The table insert is equipped with a convenient finger hole C for easy removal CHANGING THE SAW BLADE 1 FAN WARNING DISCONNECT MACHINE FROM POWER SOURCE 2 NOTE Two 7 8 wrenches ar
5. RAISING AND LOWERING THE BLADE To raise the saw blade loosen lock knob A Fig 98 and turn the blade raising handwheel B clockwise When the blade is at the desired height tighten lock Knob A To lower the blade loosen lock knob A Fig 98 and turn the handwheel B counterclockwise NOTE One full turn of the handwheel will change blade height approximately 1 4 TILTING THE BLADE To tilt the saw blade for bevel cutting loosen lock knob D Fig 98 and turn the tilting handwheel C When the desired blade angle as shown on scale and pointer E tighten lock knob D ADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPS The machine is equipped with positive stops that will quickly and accurately position the saw blade at 90 degrees and 45 degrees to the table To check and adjust the positive stops proceed as follows 1 WARNING When adjusting the positive stops make certain the machine is disconnected from the power source 2 Raise the saw blade to its highest position 3 Set the blade at 90 degrees to the table by turning the blade tilting handwheel counterclockwise as far as it will go 4 Use a combination square A Fig 99 to see if the blade is at 90 degrees to the table surface 5 If the blade is not at 90 degrees to the table loosen set screw B Fig 99 with 5 32 allen wrench C and turn the blade tilting handwheel until the blade is 90 degrees to the table Turn set screw B clockwise
6. is level with the saw table before tightening three screws B Fig 40 ASSEMBLING SWITCH TO EXTENSION WING 1 Assemble switch A Fig 41 behind the lip of extension wing B insert 5 16 18 x 1 flat head screw C then assemble flat washer and locknut 2 Fig 42 illustrates the switch assembled to the extension wing UNIFENCE ASSEMBLY INSTRUCTIONS ASSEMBLING TABLE BOARD TO SAW 1 Lay the table board upside down on the floor or bench Fig 44 2 Assemble the two table legs A Fig 45 to the bottom of the table using eight 48 x 3 4 self tapping wood screws NOTE Refer to Fig 43 for the hole location for the 30 Unifence table legs 3 Insert foot adapter T Fig 46 into the bottom of each leg A Assemble the 3 8 jam nut V Fig 46 approximately 3 4 of the way onto leveling screw W Thread the leveling screw W Fig 46 into foot adapter Fig 47 illustrates the foot leveling assembly on the table leg Assemble the remaining foot assembly to the other table leg in the same manner NOTE Height adjustments can be made later SO E a SS nee TM ULT UM DL UA Foot adapter T Leveling screw W Fig 46 Fig 47 20 4 Assemble shelf support bracket M Fig 48 to the table legs A using two U clamps N 1 4 flat washers and 1 4 20 hex nuts P NOTE Height adjustments to the bracket can be made later
7. Canada call 1 800 463 3582 OOO OO ON A AN A A A CR mae eR A A A A A AA A A A aA A A a AA AN ANA EA OG gente OS DA lt OS DA lt Q0 A d e Q A d KA oe lt ee Two Year Limited W e WO Year Limite arran e x i OO X Delta will repair or replace at its expense and at its option any Delta machine machine part or machine accessory which in normal use has proven to be defective in workmanship or material provided that the customer returns the product 0 ANA prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two years and provides Delta with reasonable opportunity to verify the alleged defect by inspection Delta may require that Q aS electric motors be returned prepaid to a motor manufacturer s authorized station for inspection and repair or replacement s S Delta will not be responsible for any asserted defect which has resulted from normal wear misuse abuse or repair or KY alteration made or specifically authorized by anyone other than an authorized Delta service facility or representative Under lt lt no circumstances will Delta be liable for incidental consequential damages resulting from defective products This 90 6S warranty is Delta s sole warranty and sets forth the customer s exclusive remedy with respect to defective products all SS
8. KR WP 17 18 19 20 21 22 23 19 20 21 22 23 24 25 a Ol ONS Combination Dust Chute Support Panel Motor Pulley Motor Pulley Guard Drive Belt Spring Pins 2 for Mounting Motor Motor Mounting Plate Lockwashers 4 Flat Washers 4 5 16 18 x 3 4 Carriage Head Screws 4 5 16 Hex Nuts 4 5 16 Hex Nuts 8 5 16 Lockwashers 8 5 16 Flat Washers 5 16 18 x 5 8 Hex Head Screws 8 Rubber Feet 4 10 32 x 12 Screws 8 10 Keps Nuts 8 10 1 2 Sheet Metal Screws 3 Grommet Front Leg Panel Rear Leg Panel Unifence Body Fence Shelf Support Bracket Front Table Support Table Board Table Legs 2 Front T Slot Guide Rail Leg Adapter Insert 2 3 8 16 Nut 2 Leveling Screws 2 7 16 20 x 3 4 Hex Head Screws Lockwashers 3 ea U Bolts 2 Angle Brackets 5 1 4 20 x 3 4 Carriage Head Screws Flat Washers and 1 4 20 Hex Nuts 5 ea Flat Washers and 1 4 20 Hex Nuts for U Bolts 4 ea 8 3 4 Hex Washer Head Screws 14 3 8 16 x 1 Hex Head Bolts Flat Washers and Hex Nuts 5 ea 1 4 20 Hex Head Bolt Flat Washer and Hex Nut 1 ea Guide Rail End Caps 2 ea with Rail Unifence Flip Stop Parts Rear Guide Rail 1 Table Adapter Plate 1 Cursor not shown 3 8 16 x 1 1 4 Hex Head Bolt Flat Washer and Nut 1 not shown BIESEMEYER T SQUARE FE
9. a workpiece that is twisted or warped or does not have a straight edge to guide along the fence using featherboards when the anti kickback device cannot be used never sawing a large workpiece that cannot be controlled never using the fence as a guide when crosscutting never sawing a workpiece with loose knots or other flaws ALWAYS USE GUARDS SPLITTER AND ANTI KICKBACK FINGERS except when otherwise directed in the manual REMOVE CUT OFF PIECES AND SCRAPS from the table before starting the saw The vibration of the machine may cause them to move into the saw blade and be thrown out After cutting turn the machine off When the blade has come to a complete stop remove all debris NEVER START THE MACHINE with the workpiece against the blade m OWP 10 11 12 13 14 15 16 17 18 19 20 21 22 HOLD THE WORKPIECE FIRMLY against the miter gauge or fence NEVER run the workpiece between the fence and a moulding cutterhead NEVER perform free hand operations Use either the fence or miter gauge to position and guide the workpiece USE PUSH STICK S for ripping a narrow workpiece AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade KEEP ARMS HANDS AND FINGERS away from the blade NEVER have any part of your body in line with the path of the saw blade NEVER REACH AROUND or over the saw
10. and or used for any application other than that for which it was designed If you have any questions relative to a particular application DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the product Technical Service Manager Delta Machinery 4825 Highway 45 North Jackson TN 38305 IN CANADA 505 SOUTHGATE DRIVE GUELPH ONTARIO N1H 6M7 WARNING FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY 1 FOR YOUR OWN SAFETY READ INSTRUCTION MANUAL BEFORE OPERATING THE MACHINE Learn the machine s application and limitations as well as the specific hazards peculiar to it 2 KEEP GUARDS IN PLACE and in working order 3 ALWAYS WEAR EYE PROTECTION Wear safety glasses Everyday eyeglasses only have impact resistant lenses they are not safety glasses Also use face or dust mask if cutting operation is dusty These safety glasses must conform to ANSI 287 1 requirements NOTE Approved glasses have 287 printed or stamped on them 4 REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from machine before turning it on 5 KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents 6 DON T USE IN DANGEROUS ENVIRONMENT Don t use power tools in damp or wet locations or expose them to rain Keep work area well lighted 7 KEEP CHILDREN AND VISITORS AWAY All children and visitors should b
11. and work are pulled back to the starting point Before pulling the work back it is good practice to give the work a little sideways shift to move the work slightly away from the saw blade Never pick up any short length of free work from the table while the saw is running Never touch a cut off piece unless it is at least a foot long For added safety and convenience the miter gage can be fitted with an auxiliary wood facing C as shown in Fig 121 that should be at least 1 inch higher than the maximum deth of cut and should extend out 12 inches or more to one side or the other depending on which miter gage slot is being used This auxiliary wood facing C can be fastened to the front of the miter gage by using two wood screws A through the holes provided in the miter gage body and into the wood facing 38 Fig 121 VN WARNING NEVER USE THE BIESEMEYER FENCE SYSTEM AS A CUT OFF GAGE WHEN CROSS CUTTING WITHOUT USING B FIG 121A When cross cutting a number of pieces to the same length a block of wood B can be clamped to the fence and used as a cut off gage as shown in Fig 121A It is important that this block of wood always be positioned in front of the saw blade as shown Once the cut off length is determined secure the fence and use the miter gage to feed the work into the cut This block allows the cut off piece to move freely along the table surface without binding between the fence and the saw blade thereby elim
12. blade NEVER attempt to free a stalled saw blade without first turning the machine OFF PROPERLY SUPPORT LONG OR WIDE workpieces NEVER PERFORM LAYOUT assembly or set up work on the table work area when the machine is running TURN THE MACHINE OFF AND DISCONNECT THE MACHINE from the power source before installing or removing accessories before adjusting or changing set ups or when making repairs TURN THE MACHINE OFF disconnect the machine from the power source and clean the table work area before leaving the machine LOCK THE SWITCH IN THE OFF POSITION to prevent unauthorized use ADDITIONAL INFORMATION regarding the safe and proper operation of this machine is available from the Power Machine Institute 1300 Summer Avenue Cleveland OH 44115 2851 Information is also available from the National Safety Council 1121 Spring Lake Drive Itasca IL 60143 3201 Please refer to the American National Standards Institute ANSI 01 1 Safety Requirements for Woodworking Machines and the U S Department of Labor OSHA 1910 213 Regulations SAVE THESE INSTRUCTIONS Refer to them often and use them to instruct others POWER CONNECTIONS A separate electrical circuit should be used for your tools This circuit should not be less than 12 wire and should be protected with a time lag fuse If an extension cord is used use only 3 wire extension cords which have 3 prong grounding type plugs and matching receptacle which will acc
13. pushblock as a holddown Degrease the table then apply the TopCote accordingly COMMON SAWING OPERATIONS Common sawing operations include ripping and cross cutting plus a few other standard operations of a fundamental nature As with all power tools there is a certain amount of hazard involved with the operation and use of the machine Using the machine with the respect and caution demanded as far as safety precautions are concerned will considerably lessen the possibility of personal injury However if normal safety precautions are overlooked or completely ignored personal injury to the operator can result NOTE THE USE OF ATTACHMENTS AND ACCESSORIES NOT RECOMMENDED BY DELTA MAY RESULT IN THE RISK OF INJURY CROSS CUTTING Cross cutting requires the use of the miter gage to position and guide the work Place the work against the miter gage and advance both the gage and work toward the saw blade as shown Fig 120 The miter gage may be used in either table slot When bevel cutting blade tilted use the table groove that does not cause interference of your hand or miter gage with the saw blade guard Start the cut slowly and hold the work firmly against the miter gage and the table One of the rules in running a saw is that you never hang onto or touch a free piece of work Hold the supported piece not the free piece that is cut off The feed in cross cutting continues until the work is cut in two and the miter gage
14. to the left side of the saw table Fig 128 USING AUXILIARY WOOD FACING ON RIP FENCE Some special operations when using the moulding cutterhead require the addition of a wood facing A Fig 130A to one side of the rip fence The wood facing is attached to the fence with wood screws through holes drilled in the fence Stock that is 3 4 inch is suitable for most work although an occasional job may require one inch facing Fig 130A 41 USING ACCESSORY MOULDING CUTTERHEAD Moulding is cutting a shape on the edge or face of the work Cutting mouldings with a moulding cutterhead in the circular saw is a fast safe and clean operation The many different knife shapes available make it possible for the operator to produce almost any kind of mouldings such as various styles of corner moulds picture frames table edges etc The moulding head consists of a cutterhead in which can be mounted various shapes of steel knives Fig 131 Each of the three knives in a set is fitted into a groove in the cutterhead and securely clamped with a screw The knife grooves should be kept free of sawdust which would prevent the cutter from seating properly IMPORTANT For certain cutting operations dadoing and moulding where the workpiece is not cut completely through the blade guard and splitter assembly cannot be used Loosen screws G and H Fig 132 Lift up and swing blade guard and splitter assembly W Fig 133 to the rear
15. 1 2 long flat head Phillips screws flat washers and hex nuts to the end piece J of the table and retighten Fasten the remaining leg to the extension table in the same manner 10 Place table assembly N Fig 85 in position between the two rails Make sure end of table O is flush against saw table P Use a bar clamp Q to snug up end of rails to hold table in position Use a straight edge to make sure table O is in the same plane and level with saw table P Lightly tap table up or down and adjust leveling screws H Fig 86 in bottom of legs When the table O Fig 85 is level and in the same plane with saw table P tighten bar clamp Q to hold in position Then drill 1 4 through holes in the front and rear of the extension table using the holes S provided in rails as template Fig 86 Fig 87 11 After the holes have been drilled in the edge of the front and rear extension table board fasten both front and rear rail to table using the 1 1 2 flat head Phillips screws T Fig 87 1 1 4 O D flat washers U and hex nuts V NOTE The 1 1 4 flat washer cannot be used on the end holes X shown covered by clamp 12 Lay the guide tube B Fig 88 on the saw table and line up the threaded holes C on bottom of guide tube B with the through holes D on the front rail A in seven places 13 Position the guide tube B Fig 89 on the front rail and fasten the guide tube to the rail using th
16. 2 Phone 418 877 7112 Fax 418 877 7123 1447 Begin St Laurent Montr al Qu bec HAR 1V8 Phone 604 420 0102 Phone 514 336 8772 Fax 604 420 3522 Fax 514 336 3505 The following are trademarks of PORTER CABLE DELTA Las siguientes son marcas re istradas de PORTER CABLE S A INNOVATION THAT JETSTREAM LASERLOC OMNIJIG POCKET CUTTER PORTA BAND PORTA PLANE PORTER CABLE QUICKSANDS SANDTRAP SAW BOSS SPEED BLOC SPEEDMATIC SPEEDTRONIC STAIR EASE THE PROFESSIONAL EDGE THE PROFESSIONAL SELECT TIGER CUB TIGER TORQBUSTER WHISPER SERIES DURATRONIC FLEX FRAME SAW M MICRO NETWORK RIPTIDE TRU MATCH WOODWORKER S CHOICE THE AMERICAN WOOD SHOP design AUTO SET M B O S S M BUILDER S SAW M CONTRACTOR S SAW DELTA M DELTACRAFT M JET L Aciu KICKSTAND THE LUMBER COMPANY Gesign MICRO SET Q3 QUICKSET QUICKSET ST aE e E CENTER SIDEKICK UNIFENCE UARD UNIRIP UNISAW VERSA FEEDER mc MANITOBA 1699 Dublin Avenue Winnipeg Manitoba R3H 0H2 Phone 204 633 9259 Fax 204 632 1976 ONTARIO 505 Southgate Drive Guelph Ontario N1H 6M7 Phone 519 836 2840 Fax 519 767 4131 BRITISH COLUMBIA 8520 Baxter Place Burnaby B C V5A 4T8 Trademarks noted with and are eo in the United States Patent and
17. 20 hex nuts 4 NOTE A common hardware package is used for several different models therefore you may have leftover hardware Fig 5 Fig 6 Fig 7 ASSEMBLY INSTRUCTIONS WARNING MAKE SURE THE SAW IS SECURELY ATTACHED TO THE STAND BEFORE PERFORMING ANY CUTTING OPERATIONS DO NOT OPERATE THIS MACHINE UNTIL YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL ASSEMBLING SAW STAND 1 Assemble the dust chute and support panel A Fig 8 to the inside of the front stand panel B with three 10 x 1 2 sheet metal screws 2 Insert four 10 32 x 1 2 screws D Fig 9 through support panel and dust chute Install four 10 32 hex nuts E Fig 9 NOTE The front stand panel will have the saw identity labels facing you Do not completely tighten the stand hardware at this time Also make certain the dust chute support panel A Fig 9 is located under the lip of front stand panel B 3 Assemble the other end of dust chute and support panel A Fig 10 to rear stand panel F as shown with four 10 32 x 1 2 screws and 10 32 hex nuts which are shown at C NOTE Do not completely tighten stand hardware at this time Fig 10 ASSEMBLING SAW TO STAND 1 Turn saw table face down on a piece of cardboard to protect the table surface Place stand B Fig 11 onto saw A Align eight holes in the stand B with mounting holes in the saw A and fasten with eight 5 16 18 screws flat washers lockwashers
18. CORD TO THE SWITCH ASSEMBLY MAKE CERTAIN THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE 1 Insert the pronged motor plug A Fig 26 into the female receptacle B of switch to motor cord C 2 Fig 27 illustrates the motor cord connected to the switch assembly ASSEMBLING BLADE GUARD AND SPLITTER ASSEMBLY WARNING DISCONNECT MACHINE FROM POWER SOURCE 1 Fasten the rear splitter mounting bracket A Fig 28 to the rear trunnion using the two 1 4 20 x 3 4 hex head screws B and flat washers Do not completely tighten the two screws B at this time 2 Raise saw arbor to its highest position With wrenches supplied remove the saw blade from the saw Refer to section CHANGING THE SAW BLADE of this manual 3 Remove screw and large washer C Fig 29 from the inside splitter mounting bracket 4 Use straight edge to check to see if the top and bottom of the inside splitter bracket D Fig 30 is aligned with the inner arbor flange E 16 5 If an alignment is necessary loosen the two screws F Fig 31 align bracket D with the arbor flange E and tighten screws F 6 Loosely assemble large washer and screw C Fig 31 to the inside splitter bracket This screw and washer was removed in STEP 3 7 Assemble the blade guard and splitter assembly G Fig 32 between the large washer C and the splitter bracket and tighten screw H with wrench supplied 8 Fasten the rear of
19. ENCE BODY 1 Remove two screws and flat washers A Fig 68 and assemble the cursor B to the Unifence body C Heplace the two screws and flat washers A 2 Fig 69 illustrates the cursor B assembled to the Unifence body Final adjustment to the cursor B will be made later ASSEMBLING UNIFENCE BODY TO GUIDE RAIL 1 Turn fence body A Fig 70 upside down and lay it on a table or bench Push handle B in against fence body Make certain the surface C of clamp bracket is parallel to the face D of the fence body and that the inside edge E of the clamp bracket is parallel to surface F of the fence body Turn handle B Fig 70 if necessary 2 Place fence body A Fig 71 onto the guide rail making sure that the clamp bracket is inserted into channel G on rail Notice that the clamp handle B is turned to the left indent position 3 Turn handle B Fig 72 to the right indent position This action will prevent fence clamp from sliding out of the channel G 4 Lock fence body A to the guide rail by pushing down on handle B Fig 73 25 Fig 73 ASSEMBLING UNIFENCE TO UNIFENCE BODY 1 The fence A can be assembled to clamp plate B in either the horizontal position as shown in Fig 74 or the vertical position as shown in Fig 75 Make certain that the two lock knobs C are loose and slide fence A onto clamp plate B as shown Then tighten the two lock knobs 2 For most cutting op
20. Electric Code 3 Grounded cord connected tools intended for use on a supply circuit having a nominal rating between 150 250 volts inclusive If the tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig C The tool willhave a grounding plug that looks like the plug illustrated in Fig Make sure the tool is connected to an outlet having the same configuration as the plug No adapter is available or should be used with this tool If the tool must be reconnected for use on a different type of electric circuit the reconnection should be made by qualified service personnel and after reconnection the tool should comply with all local codes and ordinances WARNING IN ALL CASES MAKE CERTAIN THE RECEPTACLE IN QUESTION IS PROPERLY GROUNDED IF YOU ARE NOT SURE HAVE A QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER Fig B GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES Fig C MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS Ampere Total Length Gauge of Rating Volts Extension Cord of Cord in Feet 120 up to 25 120 25 50 120 50 100 120 100 150 120 up to 25 120 25 50 120 50 100 120 100 150 120 120 120 120 GREATER THAN 50 FEET NOT RECOMMENDED Fig D EXTENSION CORDS Use proper extension cords Make sure your extension co
21. FENCE LOCKING HANDLE When the fence locking handle A is pushed to the down position Fig 117 the fence body B should be completely clamped to the guide rail If the fence body B is not completely clamped to the guide rail when the handle A is in the position shown in Fig 117 lift up the locking handle A Fig 118 and slightly tighten two adjustment plugs using arbor wrench or 7 8 wrench Adjustment plugs C should be tightened an equal amount Check to see if the fence body B is completely fastened to the rail by pushing down on locking lever A Adjust further if necessary IMPORTANT AFTER ADJUSTING THE CLAMPING ACTION OF THE FENCE LOCKING HANDLE CHECK TO SEE IF THE FENCE IS PARALLEL TO THE MITER GAGE SLOT ADJUST IF NECESSARY REPOSITIONING MOTOR FOR STORAGE When the saw is not in use the motor can be repositioned so that it hangs straight down at the rear enabling you to move the saw against a wall This can be accomplished by removing the belt and repositioning the motor and motor mounting plate as shown in Fig 119 AA d y n 7 Un PROTECTING CAST IRON TABLE FROM RUST To clean and protect cast iron tables from rust you will need the following materials 1 pushblock from a jointer 1 sheet of medium Scotch Brite Blending Hand Pad 1 can of WD 40 1 can of degreaser 1 can of TopCote Aerosol Apply the WD 40 and polish the table surface with the Scotch Brite pad using the
22. Hold the work with both hands and push it along the fence and into the saw blade Fig 125 The work can then be fed through the saw blade with one or two hands After the work is beyond the saw blade and anti kickback fingers the hand is removed from the work When this is done the work will either stay on the table tilt up slightly and be caught by the end of the rear guard or slide off the table to the floor Alternately the feed can continue to the end of the table after which the work is lifted and brought along the outside edge of the fence The cut off stock remains on the table and is not touched until the saw blade has stopped unless it is a large piece allowing safe removal When ripping boards longer than three feet use a work support at the rear of the saw to keep the workpiece from falling off the saw table 2 If the ripped work is less than 4 inches wide a push stick should always be used to complete the feed as shown in Fig 126 The push stick can easily be made from scrap material as explained in the section CONSTRUCTING A PUSH STICK 3 Ripping narrow pieces can be dangerous if not done carefully Narrow pieces usually cannot be cut with the guard in position If the workpiece is short enough use a pushboard When ripping material under 2 inches in width a flat pushboard is a valuable accessory since ordinary type sticks may interfere with the blade guard When using a pushboard the width of the pushboard
23. Limited Edition 10 Contractor s Saw with 30 Unifence Model 36 426 mt RJ with 30 Biesemeyer Model 36 431 P Tage me Be PART NO 422 19 651 0050 05 28 02 Copyright 2002 Delta Machinery To learn more about DELTA MACHINERY visit our website at www deltamachinery com For Parts Service Warranty or other Assistance please call 1 800 223 7278 in Canada call 1 800 463 3582 TIWANVIN NOILONGLSNI GENERAL SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed As with all machinery there are certain hazards involved with the operation of the product Using the machine with respect and caution will considerably lessen the possibility of personal injury However if normal safety precautions are overlooked or ignored personal injury to the operator may result Safety equipment such as guards push sticks hold downs featherboards goggles dust masks and hearing protection can reduce your potential for injury But even the best guard won t make up for poor judgment carelessness or inattention Always use common sense and exercise caution in the workshop lf a procedure feels dangerous don t try it Figure out an alternative procedure that feels safer REMEMBER Your personal safety is your responsibility This machine was designed for certain applications only Delta Machinery strongly recommends that this machine not be modified
24. NCE SYSTEM The T Square Commercial Fence System includes the fence assembly front rail rear rail front guide tube and right extension table Model 78 943 for 30 capacity IMPORTANT The T Square Fence System is designed to be used ONLY with a supporting extension table UNPACKING Carefully unpack the T Square fence system from the shipping carton s Figure s 5 6 amp 7 illustrates all the items supplied with the 78 914 fence system 1 Rear Rail 2 Front Rail 3 Guide Tube 4 T Square Fence Assembly o Template for aligning front rail to saw table for fastening guide tube to front rail 6 1 4 20 x 1 2 long hex head screws 7 7 Lock washers 7 for fastening rear rail to saw table and sheet metal extension wing if applicable 8 3 8 24 x 1 1 4 long hex head cap screws 2 9 7 8 O D flat washers 2 10 Lock washers 2 11 3 8 24 hex nuts 2 for fastening front rail to saw table 12 3 8 16 x 1 1 4 long flat head screws 2 13 7 8 O D flat washers 2 14 Lock washers 2 15 3 8 16 hex nuts 2 for fastening front and rear rails to right extension table 16 1 4 20 x 1 1 2 long flat head Phillips screws 8 17 1 1 4 O D Flat Washers 6 18 1 4 20 hex nuts 8 19 Extension Table for fastening extension table legs 20 Legs 2 21 8 x 5 8 long wood screws 8 22 1 4 20 x 1 1 2 flat head Phillips screws 4 23 1 4 flat washers 4 24 1 4
25. NEVER USE THE DADO HEAD IN BEVEL POSITION Fig 137 Fig 138 WARNING ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS COMPLETED Fig 140 a CONSTRUCTING A FEATHERBOARD Fig 141 illustrates dimensions for making a typical featherboard The material which the featherboard is constructed of should be a straight piece of wood that is free of knots and cracks Featherboards are used to keep the work in contact with the fence and table as shown in Fig 141A and help prevent kickbacks Clamp the featherboards to the fence and table so that the leading edge of the featherboards will support the workpiece until the cut is completed An 8 high flat board can be clamped to the rip fence and the featherboard can be clamped to the 8 high board Use featherboards for all non thru sawing operations where the guard and splitter assembly must be removed Always replace the guard and splitter assembly when the non thru sawing operation is completed Kerf should be 7 7 about 1 4 apart Further information on the safe and proper operation of table saws is available in the Delta Getting the Most Out of Your Table Saw How To Book Catalog No 11 400 Additional Information on table saw safety 1 also available by writing to NATIONAL SAFETY COUNCIL 1121 SPRING LAKE DRIVE ITASCA IL 60143 3201 Fig 141A 44 BIESEMEYER T SQUARE FENCE SYSTEM FENCE OPERATION IMPORTANT Before operating fence make sure
26. R PHOTO ILLUSTRATES THE CURRENT PRODUCTION MODEL ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR LABELING OR ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY UNPACKING AND CLEANING Carefully unpack the table saw and all loose items from the shipping containers Remove the protective coating from the machined surfaces of the saw This coating may be removed with a soft cloth moistened with kerosene do not use acetone gasoline or lacquer thinner for this purpose After cleaning cover the unpainted surfaces with a good quality household floor paste wax Fig 2 illustrates the components of the table saw Fig 3 illustrates the components of the saw stand Fig 4 illustrates the components of the Unifence Figs 5 6 and illustrates the components of the Biesemeyer Fence 1 Contractor s Saw 12 5 16 18 x 5 8 Carriage Head Screw 2 Blade Tilting Handwheel 13 5 16 Flat Washer 3 Handwheel Lock Knob 14 5 16 18 Hex Nut 4 Blade Guard and Splitter Assembly 15 Arbor Wrenches 2 5 Table Insert 16 Extension Table 6 Miter Gage 17 7 16 20 x 1 3 4 Hex Head Screws 7 Miter Gage Handle for assembling extension table 3 8 Miter Gage Handle Cap Is 19 1 4 20 3 4 Flat head Screw 10 1 4 20 3 4 Hex Head Screws 2 20 Flat Washer 11 1 4 Flat Washers 2 21 Hex Nut Fig 3 UNIFENCE T SLOT RAIL FENCE SYSTEM Fig 4 Oo 0
27. T BE USED WHEN DADOING OR MOULDING IT MUST BE REMOVED OR SWUNG TO THE REAR OF THE SAW AS DESCRIBED IN USING ACCESSORY MOULDING CUTTERHEAD SECTION 1 Dadoing is cutting a rabbet or wide groove into the work Most dado head sets are made up of two outside saws and four or five inside cutters Fig 136 Various combinations of saws and cutters are used to cut grooves from 1 8 to 13 16 for use in shelving making joints tenoning grooving etc The cutters are heavily swaged and must be arranged so that this heavy portion falls in the gullets of the outside saws as shown in Fig 137 The saw and cutter overlap is shown in Fig 138 A being the outside saw B an inside cutter and C a paper washer or washers used as needed to control the exact width of groove A 1 4 groove is cut by using the two outside saws The teeth of the saws should be positioned so that the raker on one saw is beside the cutting teeth on the other saw 2 Attach the dado head set D Fig 139 to the saw arbor IMPORTANT The blade guard and splitter assembly cannot be used when dadoing and must be removed or swung to the rear of the saw as explained previously in this manual Auxiliary jigs fixtures push sticks and feather boards should also be used Also the accessory dado head table insert E Fig 139 must be used in place of the standard table insert 3 Fig 140 shows a typical dado operation using the miter gage as a guide N WARNING
28. Trademark Office and may also be registered in other countries Las Marcas Registradas con el signo de y son registradas por la Oficina de Registros y Patentes de los Estados Unidos y tambi n pueden estar registradas en otros paises Printed in U S A
29. YLAND Elkridge 21075 Baltimore 7397 102 Washington Blvd Phone 410 799 9394 Fax 410 799 9398 MASSACHUSETTS Braintree 02185 Boston 719 Granite Street Phone 781 848 9810 Fax 781 848 6759 Franklin 02038 Boston Franklin Industrial Park 101E Constitution Blvd Phone 508 520 8802 Fax 508 528 8089 MICHIGAN Madison Heights 48071 Detroit 30475 Stephenson rnay nona 2 YA 500 Fax 597 5004 MINNESOTA Minneapolis 55429 5522 Lakeland Avenue North Phone zd S 561 9080 Fax 561 0653 MISSOURI North Kansas City 64116 1141 Swift Avenue P O Box 12393 Phone 816 221 2070 Fax 816 221 2897 St Louis 63119 7574 Watson Road Phone 314 968 8950 Fax 314 968 2790 NEW YORK Flushing 11365 1595 N Y C 175 25 Horace Harding Expwy Phone 718 225 2040 Fax 718 423 9619 NORTH CAROLINA Charlotte 28270 9129 Monroe Road Suite 115 Phone 704 841 1176 Fax 704 708 4625 OHIO Columbus 43214 4560 Indianola Avenue Phone 614 263 0929 Fax 614 263 1238 Cleveland 44125 8001 Sweet Valley Drive Unit 19 Phone 216 447 9030 Fax 216 447 3097 OREGON Portland 97230 4916 NE 122 nd Ave Phone 503 252 0107 Fax 503 252 2123 PENNSYLVANIA Willow Grove 19090 520 North York Road Phone 215 658 1430 Fax 215 658 1433 TEXAS Carrollton 75006 Dallas 1300 Interstate 35 N Suite 112 Phone 972 446 2996 Fax 972 446 8157 Houston 77055 Wes
30. and hex nuts one of which is shown at C Fig 11 Assemble flat washers onto screws place screws through holes assemble lockwashers then hex nuts finger tight Do not completely tighten hardware at this time 2 Install four rubber feet D Fig 11 on the end of each stand leg B 3 Turn saw table face up Fig 11 11 ASSEMBLING BLADE TILTING HANDWHEEL 1 Attach blade tilting handwheel A Fig 13 to shaft B Make certain slot C in handwheel is engaged with roll pin D on the shaft 2 Thread locking lever E Fig 14 on shaft 3 Fig 14 illustrates the blade tilting handwheel A and locking lever E assembled to the saw MOTOR The motor shipped with your saw is a 1 1 2 H P at 115 volts or 2 H P at 230 volts Ball Bearing Capacitor Start Capacitor Run motor This motor has been especially selected to best supply power to your machine and the relative safety of the machine is enhanced by its use Use only this motor as the use of other motors may be detrimental to the performance and safety of the saw ASSEMBLING MOTOR TO MOTOR MOUNTING PLATE WARNING WHEN ASSEMBLING THE MOTOR TO THE MOTOR MOUNTING PLATE MAKE CERTAIN THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE 1 Assemble the motor A to the motor mounting plate B as shown in Fig 15 using four 5 16 18 carriage bolts flat washers star washers and hex nuts C Assemble star washers on bolts place bolts throug
31. belt and pulley guard bracket G Fig 21 between the motor plate M and motor mounting plate L as shown 5 Position belt and pulley guard bracket G Fig 22 so that the motor pulley B is centered and through the hole in the belt and pulley guard bracket 6 Useastraight edge to align the motor pulley with the arbor pulley If necessary adjust the motor pulley B Fig 22 in or out on the motor shaft Tighten the four hex nuts refer back to C Fig 15 that fasten the motor to the motor mounting plate 7 Lift the motor and assemble the drive belt H Fig 23 to the arbor pulley and motor pulley B The weight of the motor will provide the correct belt tension 8 VS WARNING IMMEDIATELY AFTER ASSEMBLING THE BELT RAISE THE SAW BLADE TO ITS MAXIMUM HEIGHT AND TILT THE SAW BLADE TO 45 DEGREES CHECK TO SEE IF THE MOTOR J FIG 24 IS BELOW THE TOP OF THE TABLE SURFACE K IF THE MOTOR J IS ABOVE THE TOP OF THE TABLE SURFACE MOVE THE MOTOR TO THE LEFT UNTIL THE END BELL J OF THE MOTOR IS BELOW THE TOP OF THE TABLE SURFACE THEN RE ALIGN THE MOTOR PULLEY TO THE ARBOR PULLEY 9 Assemble the outer cover E Fig 25 of the belt and pulley guard assembly which was removed in STEP 3 and fasten with external tooth lockwasher and wing nut D IMPORTANT Make certain the outer cover does not interfere with the drive belt and the motor pulley CONNECTING MOTOR CORD TO SWITCH ASSEMBLY WARNING BEFORE CONNECTING MOTOR
32. e 1 4 20 x 1 2 long hex head screws and lockwashers in seven places Place lockwasher onto screw and assemble into rail Fig 89 29 FASTENING STAND TO SUPPORTING SURFACE IF DURING OPERATION ANY TENDENCY EXISTS FOR THE SAW TO TIP OVER SLIDE OR WALK ON THE SUPPORTING SURFACE THE SAW STAND SHOULD BE SECURED TO THE FLOOR SURFACE THE RUBBER FEET OF THE STAND FEATURE HOLES WHICH ALLOW EASY MOUNTING WITHOUT REMOVING THE SAW FROM THE STAND OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING SAW 1 The on off switch is located underneath the switch shield A Fig 94 To turn the saw ON move switch trigger B to the up position 2 To turn the saw OFF simply push down on switch shield A Fig 95 Fig 94 LOCKING SWITCH IN THE OFF POSITION IMPORTANT When the machine is not in use the switch should be locked in the OFF position to prevent unauthorized use using a padlock C Fig 96 with a 3 16 diameter shackle OVERLOAD PROTECTION The motor supplied for use with your saw is equipped with a reset overload relay button A Fig 97 If the motor shuts off or fails to start due to overloading cutting stock too fast using a dull blade using the saw beyond its capacity etc or low voltage turn the switch to the OFF position let the motor cool three to five minutes and push the reset button A The motor can then be turned on again in the usual manner 30
33. e kept a safe distance from work area 8 MAKE WORKSHOP CHILDPROOF with padlocks master switches or by removing starter keys 9 DON T FORCE MACHINE It will do the job better and be safer at the rate for which it was designed 10 USE RIGHT MACHINE Don t force machine or attachment to do a job for which it was not designed 11 WEAR PROPER APPAREL No loose clothing gloves neckties rings bracelets or other jewelry to get caught in moving parts Nonslip footwear is recommended Wear protective hair covering to contain long hair 12 SECURE WORK Use clamps or a vise to hold work when practical It s safer than using your hand and frees both hands to operate machine 13 DON T OVERREACH Keep proper footing and balance at all times 14 MAINTAIN TOOLS IN TOP CONDITION Keep tools sharp and clean for best and safest performance Follow instructions for lubricating and changing accessories 15 DISCONNECT TOOLS before servicing and when changing accessories such as blades bits cutters etc 16 USE RECOMMENDED ACCESSORIES The use of accessories and attachments not recommended by Delta may cause hazards or risk of injury to persons 17 REDUCE THE RISK OF UNINTENTIONAL STARTING Make sure switch is in OFF position before plugging in power cord In the event of a power failure move switch to the OFF position 18 NEVER STAND ON MACHINE Serious injury could occur if the machine is tipped or if the cutt
34. e supplied with the saw for changing the saw blade a box end wrench A Fig 107 and open end wrench B Use only 10 saw blades rated for 3000 RPM or higher with 5 8 arbor holes 3 Remove table insert C Fig 106 and raise saw blade to its maximum height 4 Place the open end wrench B Fig 106 on the flats of the saw arbor to keep the arbor from turning and use wrench A to turn the arbor nut toward the front of the saw Remove arbor nut blade flange and saw blade 5 Assemble the new blade making certain the teeth point down at the front of the saw table and assemble outside blade flange and arbor nut With wrench B Fig 106 on the flats of the arbor to keep it from turning tighten arbor nut by turning wrench A counterclockwise 6 Replace table insert 34 STORING THE MITER GAGE RIP FENCE AND ARBOR WRENCHES 1 When not in use the miter gage A Fig 108 can be stored through the hole located at the front side of the stand 2 The rip fence B Fig 108 can be conveniently stored out of the way on the stamped ledges on the right side of the saw stand 3 Arbor wrenches C Fig 109 can be stored on one of the two notched legs DUST CHUTE The saw stand support panel D Fig 109 also serves as a natural built in dust chute This dust chute D allows the sawdust to conveniently escape out the rear of the saw stand and away from the work area FENCE OPERATION 1 Before operating fence mak
35. e sure the fence is adjusted parallel to miter gage slot as explained later on in this manual 2 For most normal ripping operations of standard size lumber the fence is used in the vertical position as shown in A Fig 110 3 When ripping thin stock use the fence in the horizontal position B Fig 111 108 4 To move the fence along the guide rail simply lift up clamp lever A Fig 112 slide fence to desired position on the rail and push down on clamp lever A to lock fence in place 5 The distance the fence is positioned away from the blade is indicated by the two witness lines B and C Fig 113 located on the cursor D The witness lines B and C indicate the distance the fence is positioned away from the saw blade Witness line B indicates the distance the fence is away from the blade when the fence is in the horizontal position Fig 111 and witness line C indicates the distance the fence is away from the blade when the fence is in the vertical position Fig 110 To adjust cursor D make a test cut with the fence in either the vertical or horizontal position measure the distance of the finished cut and move the cursor D by loosening the two screws E Fig 113 After adjustment is completed tighten the two screws 6 To remove the fence and fence body assembly F Fig 114 from the guide rail lift up on fence clamping lever A and turn lever A to the CCW indent position T
36. ept the machine s plug Before connecting the motor to the power line make sure the switch is in the OFF position and be sure that the electric current is of the same characteristics as indicated on the machine All line connections should make good contact Running on low voltage will damage the motor PAN WARNING DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP GROUNDING INSTRUCTIONS PAN WARNING THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM LOCATIONS ELECTRIC SHOCK 1 All grounded cord connected tools In the event of a malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This tool is equipped with an electric cord having an equipment grounding conductor and a grounding plug The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances Do not modify the plug provided if it will not fit the outlet have the proper outlet installed by a qualified electrician Improper connection of the equipment grounding conductor can result in risk of electric shock The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor repair or replacement of the electric cord or plug is necessary do not connect the equipment grounding conductor to a live ter
37. erations the bottom of the fence should be positioned slightly above the table surface Loosen two lock knobs C Fig 76 and place a thin object such as a scale D between the table and fence Tighten two lock knobs C BIESEMEYER T SQUARE FENCE SYSTEM ASSEMBLY INSTRUCTIONS 1 WARNING DISCONNECT MACHINE FROM POWER SOURCE 2 Assemble the front rail A Fig 77 to front of saw table using the two 3 8 16 x 1 1 4 long flat head Phillips screws B 7 8 flat washers lock washers and 3 8 16 hex nuts supplied Screws B are inserted through the two holes in the front rail and through the two through holes in the front of the saw table and fastened to the table with the flat washers lockwashers and hex nuts IMPORTANT Do not completely tighten front rail mounting hardware at this time 26 Fig 79 3 Using the template D Figures 78 and 79 check and adjust front rail at both ends of the saw table to make sure rail A is level with table surface Tighten rail mounting hardware B IMPORTANT Template D must be on saw table when checking not on extension wing 4 Assemble rear rail E Fig 80 to rear of saw table using the two 3 8 24 x 1 1 4 long hex head screws F 7 8 flat washers 3 8 24nuts and 3 8 lockwashers not shown Place flat washer on bolt then assemble bolt into rear rail then assemble lockwasher and nut 5 Make certain top edge of rail E Fig 80 is below table surface and that top edge of c
38. ew D insert screw through the table adapter plate and thread screw into right side of saw table Repeat this process for the two remaining holes NOTE Before tightening screws D use a straight edge to make sure top of the adapter plate B is level with or slightly below surface of the saw table Also make sure that the front edge of the adapter B does not stick out past the front edge of the saw table 21 Fig 49 ASSEMBLING UNIFENCE TABLE TO SAW 1 Remove screw l Fig 49 D Fig 54 before placing table on brackets Position table board A Fig 53 on three angle brackets B 2 While holding table board firmly against the saw adapter plate fasten the table to the three brackets using three 8x7 8 wood screws D E and F Fig 54 NOTE The two screws E and F Fig 54 can be tightened Screw D Fig 54 should be left slightly loose at this time CAUTION DO NOT OVER TIGHTEN TABLE MOUNTING SCREWS Over tightening screws in particle board may cause them to strip 3 Assemble the two brackets J to the rear guide rail K using the two 1 4 20 x 3 4 carriage bolts placing bolts through holes then washers and nuts L Fig 55 NOTE The long leg of the brackets J should be against the bottom of the table A 4 Fasten the table A to the two brackets J on the rear guide rail K Fig 56 using two 8x7 8 wood Screws 5 Using a straight edge S Fig 57 make certain the surface of the Un
39. h holes then assemble lockwashers and hex nuts NOTE Do not completely tighten the hex nuts at this time 12 ASSEMBLING MOTOR AND MOTOR MOUNTING PLATE TO SAW WARNING WHEN ASSEMBLING THE MOTOR AND MOTOR MOUNTING PLATE TO THE SAW MAKE CERTAIN THE MACHINE IS DISCONNECTED FROM THE POWER SOURCE 1 Depress two pins X Fig 16 and insert into holes D in each side of bracket B Pins are spring Y loaded from factory 2 Position motor and motor mounting plate A Fig 17 below bracket B to allow bracket arm to slide through large opening in motor mounting plate A 3 Depress pins C Fig 17 on both sides of bracket B and rotate motor mounting plate A until pins C are engaged in holes D Fig 16 of motor mounting plate A 4 Fig 18 illustrates the motor and motor mounting plate assembled to the rear of the saw 13 Fig 18 ASSEMBLING MOTOR PULLEY BELT AND PULLEY GUARD AND DRIVE BELT WARNING WHEN ASSEMBLING MOTOR PULLEY BELT AND PULLEY GUARD AND DRIVE BELT MAKE CERTAIN THE MOTOR IS DISCONNECTED FROM THE POWER SOURCE 1 Remove the motor shaft key that is taped to the motor 2 Insert the key A Fig 19 in the keyway on the motor shaft Assemble the motor pulley B on the motor shaft with the hub of the pulley facing out Tighten set screw C 3 Remove wing nut and external tooth lockwasher D Fig 20 and outer cover E from belt and pulley guard 4 Slide the
40. he fence assembly F can then be pulled straight off the guide rail and removed as shown in Fig 114 ADJUSTING FENCE PARALLEL TO MITER GAGE SLOTS The fence A Fig 115 should be adjusted so it is parallel to miter gage slots B To check and adjust move the fence A until the bottom front edge of the fence is in line with the edge of the miter gage slot and push down on fence clamping lever C Check to see that the fence is parallel to the miter gage slot the entire length of the table If the rear of the fence must be moved slightly tighten or loosen one of the adjustment plugs D or E Fig 115 using the arbor wrench or 7 8 wrench until the fence is parallel with the miter gage slot IMPORTANT DO NOT OVERTIGHTEN ADJUSTMENT PLUGS D AND E FIG 115 VERY LITTLE MOVEMENT OF THESE ADJUSTMENT PLUGS IS NECESSARY WHEN ADJUSTING THE FENCE PARALLEL WITH THE MITER GAGE SLOT Aa DELTA SAW GUIDE Fig ADJUSTING FENCE 90 DEGREES TO TABLE Adjust the fence so that the face of fence A Fig 116 is 90 degrees to the table To check if the fence is 90 degrees to the table place a square B on the table with one end of the square against the fence If an adjustment is necessary tighten or loosen one of two screws C or D until the fence is 90 degrees to the table IMPORTANT VERY LITTLE MOVEMENT OF THESE SCREWS C AND D IS NECESSARY TO MAKE THIS ADJUSTMENT ADJUSTING CLAMPING ACTION OF
41. icals known to cause cancer birth defects or other reproductive harm Some examples of these chemicals are lead from lead based paints crystalline silica from bricks and cement and other masonry products and arsenic and chromium from chemically treated lumber Your risk from these exposures varies depending on how often you do this type of work To reduce your exposure to these chemicals work in a well ventilated area and work with approved safety equipment such as those dust masks that are specially designed to filter out microscopic particles SAVE THESE INSTRUCTIONS Refer to them often and use them to instruct others ADDITIONAL SAFETY RULES FOR TABLE SAWS WARNING FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY DO NOT OPERATE THIS MACHINE until it is assembled installed according to the instructions OBTAIN ADVICE FROM YOUR SUPERVISOR instructor or another qualified person if you are not familiar with the operation of this machine FOLLOW ALL WIRING CODES and recommended electrical connections USE THE GUARDS WHENEVER POSSIBLE Check to see that they are in place secured and working correctly AVOID KICKBACK by keeping blade sharp and free of rust and pitch keeping rip fence parallel to the saw blade using saw blade guard and spreader for every possible operation including all through sawing pushing the workpiece past the saw blade prior to release never ripping
42. ifence table is level with the saw table by adjusting the height of the two leveling screws E Fig 58 at the base of the table legs and adjusting the height of angle brackets B Fig 53 Position hex nuts H Fig 58 against the bottom of the table legs to hold the leveling screws in position and tighten IMPORTANT Use a level side to side and front to back to make sure the Unifence table is level with the saw table Fig 58 22 Fig 57 ASSEMBLING UNIFENCE GUIDE RAIL 1 Locate the T Slot Guide Rail and mounting hardware Fig 59 from the packing material of the Unifence Remove the end caps A Fig 59 prior to assembly by inserting a flat headed screwdriver B into the channel and tap gently NOTE Take care not to damage either the cap or the rail 2 Insert two 3 8 24 x 1 hex head bolts flat washers and hex nuts C Fig 60 into the two holes F Fig 60 in the front of saw table G Screw bolts into nuts slightly leaving bolt head extended approximately 1 2 Note Make sure to use only the two holes shown at F and that washers are on the nut side of the bolt 3 Insert one 1 4 20 x 3 4 hex head bolt flat washer and hex nut D Fig 60 into the front support of the extension table E Fig 60 Screw bolt into nut slightly leaving bolt head extended approximately 1 4 Make sure washer is on the nut side of the bolt 4 From either end slide the T Slot guide rail A Fig 61 o
43. inating the possibility of kickback and injury to the operator IMPORTANT When using the block B Fig 121A as a cut off gage it is very important that the rear end of the block be positioned so the work piece is clear of the block before it enters the blade Fig 121A FOR UNIFENCE SYSTEMS ONLY THE UNIFENCE CAN BE USED AS A CUT OFF GAGE The fence can be used as a cut off gage when cross cutting a number of pieces to the same length IMPORTANT WHEN USING THE FENCE AS A CUT OFF GAGE IT IS VERY IMPORTANT THAT THE REAR END OF THE FENCE BE POSITIONED IN FRONT OF THE SAW BLADE When using the fence as a cut off gage simply position the fence A to the front Fig 122 or purchase the accessory 12 long fence B Fig 123 Fig 124 illustrates a typical operation using the accessory 12 long fence B as a cut off gage 39 RIPPING WITH THE UNIFENCE Ripping is cutting lengthwise through a board Fig 125 The rip fence A is used to position and guide the work One edge of the work rides against the rip fence while the flat side of the board rests on the table Since the work is pushed along the fence it must have a straight edge and make solid contact with the table The saw blade guard must be used On Delta saws the guard has anti kickback fingers to prevent kickback and a splitter to prevent the wood kerf from closing and binding the blade 1 Never stand in the line of the saw cut when ripping
44. ing Blesemeyer T Square Blade Guard Systems 78 960 10 System for Home Shop 52 and Commercial 50 Fence Systems With T arm assembly blade guard splitter installation bracket mounting hardware and instruction manual 78 955 10 System for Home Shop 28 40 and Commercial 26 30 and 38 Fence Systems Same as 78 960 except for fence systems 40 and under 48 Fig 151 Fig 152 ACCESSORIES A complete line of accessories is available from your Delta Supplier Porter Cable e Delta Factory Service Centers and Delta Authorized Service Stations Please visit our Web Site www deltamachinery com for a catalog or for the name of your nearest supplier WARNING Since accessories other than those offered by Delta have not been tested with this product use of such accessories could be hazardous For safest operation only Delta recommended accessories should be used with this product MODEL DESCRIPTION 34 976 Deluxe Uniguard Blade Guard 78 960 Biesemeyer 1 5 Table Saw Blade Guard System ADELTA PARTS SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network of Porter Cable e Delta Factory Service Centers and Delta Authorized Service Stations To obtain additional information regarding your Delta quality product or to obtain parts service warranty assistance or the location of the nearest service outlet please call 1 800 223 7278 In
45. ing machine is accidentally contacted 19 CHECK DAMAGED PARTS Before further use of the machine a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function check for alignment of moving parts binding of moving parts breakage of parts mounting and any other conditions that may affect its operation A guard or other part that is damaged should be properly repaired or replaced 20 DIRECTION OF FEED Feed work into a blade or cutter against the direction of rotation of the blade or cutter only 21 NEVER LEAVE MACHINE RUNNING UNATTENDED TURN POWER OFF Don t leave machine until it comes to a complete stop 22 STAY ALERT WATCH WHAT YOU ARE DOING AND USE COMMON SENSE WHEN OPERATING A POWER MACHINE DO NOT USE MACHINE WHILE TIRED OR UNDER THE INFLUENCE OF DRUGS ALCOHOL OR MEDICATION A moment of inattention while operating power tools may result in serious personal injury 23 MAKE SURE MACHINE IS DISCONNECTED FROM POWER SUPPLY while motor is being mounted connected or reconnected 24 THE DUST GENERATED by certain woods and wood products can be injurious to your health Always operate machinery in well ventilated areas and provide for proper dust removal Use wood dust collection systems whenever possible 25 SOME DUST CREATED BY POWER SANDING SAWING GRINDING DRILLING AND OTHER CONSTRUCTION ACTIVITIES contains chem
46. lored marker Fig 101A Rotate the blade toward the front of the saw by hand until the marked tooth is at the top of the table 3 Insert the miter gage into miter gage slot and position near the front edge of the blade With a combination square G place the straight edge along the face of the miter gage Position the end of the straight edge H to lightly contact the side of the marked tooth 4 Firmly hold the straight edge in place while rotating blade to the rear side of the table Firmly hold the straight edge in place to re position the miter gage to the rear side of the saw table Fig 101B Rotate the mark made in step 2 on the blade F to end of straight edge to check blade alignment gap The marked tooth F should be the same distance from the end of the straight edge in front and rear positions 5 Repeat this procedure moving from front to rear until you have visual confirmation of the blade alignment NOTE All saw blades have some run out Therefore check the alignment each time a blade is changed 6 If the blade alignment is off by 010 or the approximate thickness of a standard business card follow ADJUSTING BLADE ALIGNMENT procedure 7 Lower blade guard and saw blade before reconnecting power source 32 an m tp 2 Bee Wi A x 2 2 LAT 4 T5 14 gt e T open n di he y f 1 M 579 Aa TE SONS M ee i ie 4 PON as
47. minal Check with a qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded Use only 3 wire extension cords that have 3 prong grounding type plugs and matching 3 conductor receptacles that accept the tool s plug as shown in Fig A Hepair or replace damaged or worn cord immediately 2 Grounded cord connected tools intended for use on a supply circuit having a nominal rating less than 150 volts If the tool is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig A The tool will have a grounding plug that looks like the plug illustrated in Fig A GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADE IS LONGEST OF THE 3 BLADES Fig A A temporary adapter which looks like the adapter illustrated in Fig B may be used to connect this plug to a matching 2 conductor receptacle as shown in Fig B if a properly grounded outlet is not available The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician The green colored rigid ear lug and the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box Whenever the adapter is used it must be held in place with a metal screw NOTE In Canada the use of a temporary adapter is not permitted by the Canadian
48. must be added to the width of the rip fence position setting A flat pushboard can be constructed as shown in Fig 126A and should be used as shown in Fig 126B NOTE Some special operations when using the moulding cutterhead require the addition of an auxiliary wood facing to the fence as explained in the section USING AUXILIARY WOOD FACING ON THE UNIFENCE and use of a push stick 3 4 PLYWOOD Fig 126B Fig 126A 40 4 When ripping material with a veneer facing that extends over the material the fence A should be in the horizontal position with the veneer B extending over the lip of the fence Fig 127 5 When ripping material with a veneer facing and the material is not thick enough for the veneer to extend over the lip of the fence or if the veneer facing B is on both sides of the material Fig 128 the fence can be positioned slightly above the surface of the table The veneer can be placed between the fence and the table or the veneer can straddle the fence with the material solidly against the fence as shown RIPPING ON LEFT SIDE OF SAW BLADE In some cases it may be desirable to use the fence on the left side of the saw blade This action is easily accomplished by repositioning the fence A Figs 129 and 130 fence clamp bar B and lock knobs C so that the fence A will be attached to the right side of the fence body Fig 130 The complete fence assembly D Fig 130 can easily be moved
49. n the hex head of the bolts partially inserted in step 2 and 3 above Note The bolt heads on the saw table slide into the upper t slot B Fig 61 and the bolt head on the extension table slide into the lower t slot C Fig 61 5 Slide the guide rail along until the 0 on the unifence scale is aligned with the right edge of the saw table onug the hex nuts on the saw and extension table but do not tighten at this time 6 Adjust the guide rail Fig 62 parallel with the saw table surface by placing a square H on the saw table at both the left front end of the saw table A and the right front end of the extension table B with the rule of the square against the flat surface on top of the guide rail The guide rail C Fig 62 can be adjusted up or down slightly at either end After being certain the guide rail is parallel with the table surface firmly tighten the two hex nuts that fasten the guide rail to the table Note Make sure 0 D on the unifence scale is aligned with the right edge of the saw table E Fig 61 7 Move the square H Fig 62 to the end of the Unifence table and check to make certain the same distance is kept from the top surface of the extension table K to the top surface of the guide rail C Move the front table support L Fig 63 against the guide rail C and fasten with 1 4 20 nut and flat washer M Tighten ar eo two screws one of which is shown at N Fig 63 that g
50. of the saw and retighten H CAUTION Always return and fasten the blade guard and splitter assembly to its proper operating position for normal thru sawing operations as shown in Fig 32 and 33 A moulding cutterhead A Fig 134 is shown assembled to the sawarbor Also the accessory moulding cutterhead table insert B must be used in place of the standard table insert When using the moulding cutterhead add wood facing C to the face of the rip fence Fig 135 The wood facing is attached to the fence with wood screws through holes which must be drilled in the fence Stock that is 3 4 inch thick is suitable for most work although an occasional job may require 1 inch facing Position the wood facing over the cutterhead with the cutterhead below the surface of the table Turn the saw on and raise the cutterhead The cutterhead will cut its own groove in the wood facing Fig 135 shows a typical moulding operation See accessories for molding cutterhead set NEVER USE MOULDING CUTTERHEAD IN A BEVEL POSITION IMPORTANT NEVER RUN THE STOCK BETWEEN THE FENCE AND THE MOULDING CUTTERHEAD IRREGULAR SHAPED WOOD WILL CAUSE KICKBACK IMPORTANT Special attention should be given the grain direction Make all cuts in the same direction as the grain whenever possible WARNING ALWAYS INSTALL BLADE GUARD AFTER OPERATION IS COMPLETE Fig 135 USING ACCESSORY DADO HEAD IMPORTANT THE BLADE GUARD AND SPLITTER ASSEMBLY CANNO
51. or E Fig 146 using a 3 16 allen wrench F not supplied Replace the fence on the guide tube and check again to see if the edge of the fence is parallel with the miter gage slot along the entire length of the slot Repeat this adjustment until the fence is parallel with the miter gage slot IMPORTANT VERY LITTLE MOVEMENT OF SCREWS D AND E IS NECESSARY TO ADJUST THE FENCE PARALLEL WITH THE MITER GAGE SLOT Fig 145 45 Fig 146 ADJUSTING CLAMPING ACTION OF FENCE LOCKING HANDLE When the fence locking handle A is pushed to the down position Fig 147 the fence assembly B should be completely clamped to the guide tube C If the fence assembly B is not completely clamped to the guide tube C when the handle A is pushed down as shown in Fig 147 lift up handle A and raise fence assembly B up off the guide tube C Slightly tighten the two adjusting screws D and E Fig 148 using the 3 16 allen wrench F not supplied Adjusting screws D and E Fig 148 should be tightened an equal amount Replace fence onto the guide tube and re check to see if the fence assembly B Fig 147 is completely tightened to the guide tube C with the locking handle A pushed down Adjust further if necessary IMPORTANT AFTER ADJUSTING THE CLAMPING ACTION OF THE FENCE LOCKING HANDLE CHECK TO SEE IF THE FENCE IS PARALLEL TO THE MITER GAGE SLOT AND ADJUST IF NECESSARY Fig 147 Fig 148 LUBRICATION 1 Apply ho
52. rd is in good condition and is a 3 wire extension cord which has a 3 prong grounding type plug and matching receptacle which will accept the machine s plug When using an extension cord be sure to use one heavy enough to carry the current of the machine An undersized cord will cause a drop in line voltage resulting in loss of power and overheating Fig D shows the correct gauge to use depending on the cord length If in doubt use the next heavier gauge The smaller the gauge number the heavier the cord MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC TOOLS Ampere Total Length Gauge of Rating Volts of Cord in Feet Extension Cord 0 6 up to 50 50 100 100 200 200 300 up to 50 50 100 100 200 200 300 up to 50 50 100 GREATER THAN 100 FEET NOT RECOMMENDED Fig D OPERATING INSTRUCTIONS FOREWORD Delta 10 Contractor s Saws are designed to give high quality performance with maximum depth of cut capacity up to 3 1 8 at 90 and 2 1 8 at 45 Delta Model 36 426 includes a 30 Unifence Fence System with T Slot rail and Model 36 431 includes a 30 Biesemeyer T Square Home Shop Fence System These Delta Models come equipped with basic machine sturdy steel stand integral dust chute patented Auto Set T Slot miter gage heavy duty motor large on off paddle switch extension wing cast table convenient up front blade raising and tilting controls and 10 carbide blade NOTICE THE MANUAL COVE
53. t fasten the Unifence table to the guide rail a i er 2 n ue 1 L3 ASSEMBLING RAIL STOP 1 The Unifence Flip Stop Fig 64 can be easily assembled by inserting flip stop A into fence slide stop B which is held in place by inserting 1 4 20 x 2 hex head bolt fiber washers D and tightening hex nut E Make sure fiber washers are placed on both sides of flip stop A when assembled Do not over tighten hex nut E The flip stop must fit snuggly but move freely 2 The Rail Stop Assembly Fig 65 can then be attached to the guide rail by inserting head of 5 16 18 F hex head bolt into T Slot G positioning the stop assembly to the rail and tightening knob H finger tight 3 Use a rubber mallet P Fig 66 or a hammer and a block of wood to gently tap end cap H into both ends of the guide rail C NOTE To avoid damage to the guide rail DO NOT use a metal hammer directly against the guide rail Fig 65 Fig 66 SETTING T SLOT RAIL STOP 1 The Rail Stop Assembly Fig 67 A can be set to any number of positions along the guide rail providing a quick stop setting for the Unifence body by loosening knob B and sliding the stop along the rail to the desired position and re tighten NOTE Any number of stops can be purchased and installed to provide time saving quick stop adjustment for the Unifence body Fig 67 24 Fig 69 ASSEMBLING CURSOR TO UNIF
54. t 10 Business Center 1008 Wirt Road Suite 120 Phone 713 682 0334 Fax 713 682 4867 WASHINGTON Auburn 98001 Seattle 3320 West Valley HWY North Building D Suite 111 Phone 253 333 8353 Fax 253 333 9613 Authorized Service Stations are located in many large cities Telephone 800 438 2486 or 731 541 6042 for assistance locating one Parts and accessories for Porter Cable Delta products should be obtained by contacting any Porter Cable Delta Distributor Authorized Service Center or Porter Cable Delta Factory Service Center If you do not have access to any of these call 800 223 7278 and you will be directed to the nearest Porter Cable Delta Factory Service Center Las Estaciones de Servicio Autorizadas est n ubicadas en muchas grandes ciudades Llame al 800 438 2486 6 al 731 541 6042 para obtener asistencia a fin de localizar una Las piezas y los accesorios para los productos Porter Cable Delta deben obtenerse poni ndose en contacto con cualquier distribuidor Porter Cable Delta Centro de Servicio Autorizado o Centro de Servicio de F brica Porter Cable Delta Si no tiene acceso a ninguna de estas opciones llame al 800 223 7278 y le dirigir n al Centro de Servicio de F brica Porter Cable Delta m s cercano CANADIAN PORTER CABLE e DELTA SERVICE CENTERS ALBERTA Bay 6 2520 23rd St N E Calgary Alberta T2E 8L2 Phone 403 735 6166 Fax 403 735 6144 QUEBEC 1515 ave St Jean Baptiste Qu bec Qu bec G2E 5E
55. the blade guard and splitter bracket assembly G Fig 33 to the rear splitter mounting bracket using 5 16 18 x 5 8 carriage bolt J flat washer and 5 16 18 hex nut IMPORTANT The splitter G Fig 33 has a notch L cut in the top edge This feature will enable the blade guard to stay in the raised position to make blade changing a little easier Raise the front of blade guard M Fig 34 until the rear edge of the blade guard slips into notch L of splitter G the blade guard will stay in this position 17 9 With the blade guard L Fig 35 in the raised position assemble the saw blade K on the saw arbor with two arbor wrenches supplied 10 Use a straight edge to check to see if the saw blade is aligned with the rear of the splitter G in Figs 36 and 37 If alignment is necessary loosen the screws A Fig 37 align splitter G with the saw blade and tighten two screws A 11 Lower saw blade and install table insert P Fig 38 in the saw table IMPORTANT When installing the table insert make certain to hold on to the blade guard L The insert will automatically release the holding action on the splitter and lower the blade guard when it is installed in the table opening ASSEMBLING EXTENSION WING 1 Assemble extension wing A Fig 39 to the saw table using three 7 16 20 x 1 1 4 screws B and lockwashers C Fig 39 2 With a straight edge D Fig 39 make certain the extension wing A
56. the fence is adjusted parallel to the miter gage slot as explained later in this manual Fig 142 1 To move the fence along the guide rail simply lift up clamp lever A as shown Fig 142 slide fence to desired position on rail and push down on clamp lever A as shown in Fig 143 NOTE A magnet Fig 143 is provided to hold clamp handle A Figs 142 and 143 in the up position when moving the fence 2 The distance the fence 1 positioned away from the blade is indicated by the witness line Fig 144 located on the cursor C To adjust the cursor C make a test cut with the fence locked in position Measure the width of the finished cut and adjust the cursor C by loosening the two screws D adjusting the cursor C until the witness line B is aligned with the same marking on the scale as the finished cut Tighten the two screws D Fig 144 ADJUSTING FENCE PARALLEL TO MITER GAGE SLOTS Adjust the fence A Fig 145 so that it is parallel to the miter gage slots B To check and adjust move fence A until the bottom edge of the fence is in line with the edge of one of the miter gage slots and push down on the fence clamping lever C Check to see if the fence A is parallel to the miter gage slot the entire length of the table If an adjustment must be made lift up fence locking lever C and raise fence up off the guide tube Fig 146 Tighten or loosen one of the two adjusting screws D
57. until it bottoms 6 Adjust the pointer D Fig 100 to point to the zero degree mark on the scale by loosening screw adjusting pointer D and tightening screw E 7 Turn the blade tilting handwheel clockwise as far as it will go and use a combination square to see if the blade is at 45 degrees to the table 8 If the blade is not at 45 degrees to the table loosen set screw F Fig 99 and turn blade tilting handwheel until the blade is 45 degrees to the table Turn set screw F clockwise until it bottoms 31 Fig 100 i a 5 BACKLASH ADJUSTMENTS FOR BLADE RAISING AND BLADE TILTING MECHANISMS After a period of extended use if any play is detected in the blade raising or blade tilting mechanisms make the following adjustments VS WARNING Disconnect machine from power source 2 NOTE The machine has been turned upside down and the blade removed for clarity and safety 3 Adjusting blade raising mechanism Loosen locknut A Fig 101 and turn eccentric sleeve B until all play is removed in mechanism and tighten locknut A 4 Adjusting blade tilting mechanism Loosen locknut C Fig 101 and turn eccentric D until all play is removed in mechanism and tighten locknut C CHECKING BLADE ALIGNMENT 1 ZN WARNING Disconnect machine from power source 2 Raise blade guard and adjust blade to its highest position Mark one side of one saw blade tooth F with a dark co
58. usehold floor paste wax to fence and guide tube sliding surfaces weekly Also saw table and extension table surface should be waxed often 2 Apply grease to cam lock A Fig 149 and cam foot B occasionally to prevent wear 091 B4 SCE ARSENE Emm IDE 8 Jes N BHC ETSI s 12 SECA SST SICLICLCLICE LRSSEIECIL PRISCA f ST PAE Os act CCP _ BLADE GUARD ACCESSORIES Deluxe Uniguard Blade Guard The Delta Model 34 976 Uniguard Blade Guard with Splitter and Anti kickback Fingers Fig 151 is an accessory that can be used in place of the standard blade guard that is supplied with the Contractor s Saw The Delta Model 34 976 Uniguard Blade Guard can be mounted to the Contractor s Saw with a UniRip or Unifence fence systems 78 953 Uniguard Strap Kit Kit replaces the rear angle rail of Biesemeyer 30 and 50 Commercial Fence Systems and Home Shop Fence Systems up to 52 for mounting the No 34 976 Delta Uniguard Blade Guard Mounting hardware included Biesemeyer T Square Table Saw Blade Guard System The Biesemeyer Model 78 960 T Square Table Saw Blade Guard System Fig 152 is an accessory that can be used in place of the standard blade guard that is supplied with the Contractor s Saw Catalog List
59. ut outs are below miter gage slots before tightening screws F 27 WIDTH OF TABLE SAW APPROX 12 ON CENTER APPROX 12 ON CENTER 2 1 4 x 3 4 SEMFHARDWOOD Fig 81 6 If the accessory right extension table for use with the T Square fence was not purchased construct an extension table by following the dimensions shown in Fig 81 2f 5 3 8 3 L 1 3 4 K Fig 82 Fig 83 Markthe position of the four leg mounting holes from each end of the table Fig 82 Use a 1 4 drill bit to drill four through holes through the end piece J of the table at the dimensions shown at K L and M 8 Position the two legs H Fig 83 Assemble the four 1 4 20 x 1 1 2 leg mounting screws washers and hex nuts I into holes drilled in step 7 and tighten Mark the eight holes P to attach the legs to the table top Remove the screws and two legs H Using a 1 16 drill bit drill the eight holes 1 2 deep CAUTION DO NOT OVER TIGHTEN MOUNTING SCREWS Over tightening screws in particle board may cause them to strip Fig 84 IMPORTANT NOTE If your saw and fence system will be used with a mobile base underneath the saw base and table legs the position of the legs may have to be changed to fit onto the mobile base 9 Fasten the leg bracket L Fig 84 to the underside of table top using the eight 3 4 long wood screws four are shown at Fig 84 Assemble the four 1
Download Pdf Manuals
Related Search