DeLonghi DE605MW Oven User Manual
Contents
1. KEEP ATTENTION STAND AWAY FROM THE CONTROL PANEL LOUVERS see figure above HOT AIR WHICH ESCAPES CAN CAUSE BURNS TO HANDS FACE END OR EYES IMPORTANT PRECAUTIONS AND RECOM MENDATIONS After having unpacked the appliance check to ensure that it is not damaged In case of doubt do not use it and consult your supplier or a pro fessionally qualified technician Packing elements i e plastic bags polystyrene foam nails packing straps etc should not be left around within easy reach of children as these may cause serious injuries The packaging material is recyclable and is marked with the recycling symbol 7 5 v Do not attempt to modify the technical characteristics of the appliance as this may become dangerous to use vy Do not carry out cleaning or maintenance operations on the appliance without having previously disconnected it from the electric power supply vJ After use ensure that the knobs are in OFF position v Do not allow children or other incapable people to use the appliance without supervision v During and after use of the oven certain parts will become very hot Do not touch hot parts v Keep children away from the oven when it is in use v For DEBIG 24 SS model only This oven is supplied with a protective film on steel and aluminium parts This film must be removed before installing using the appliance v Fire risk Do not store flam2. Do not use Broiling level Oven cooking level Oven cooking level Fig 3 7 BROILING Very important the broil burner must always be used with the oven door closed Position the shelf on the second level from the top fig 3 7 Turn on the broil burner as explained in the preceding paragraphs and let the oven preheat for about 5 minutes with the door closed Place the food to be cooked above the broiler pan Introduce the broiler pan fig 3 8 in the oven The broiler pan should be placed above the shelf and it should be centered with the broil burner fig 3 7 Do not broil without using the broiling pan Important Use always suitable protective gloves when inserting removing the broiling pan shelves pans or other cooking utensils from the oven Fig 3 10 11 12 O cleaning and maintenance WARNING VERY IMPORTANT Before any operation of maintenance disconnect the appliance from the electrical mains supply Do not use a steam cleaner because the moisture can get into the appliance thus make it unsafe GENERAL RECOMANDATION y Important Before any operation of cleaning and maintenance disconnect the appliance from the electrical supply y It is advisable to clean when the appliance is cold and especially for cleaning the enamelled parts v Avoid leaving alkaline or acidic subst
3. FOR YOUR SAFETY Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel WARNING THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER Improper installation adjustment alteration services or maintenance can cause injury or property damage Consult a qualified installer service agent or the gas supplier IMPORTANT The use of suitable protective clothing gloves is recommended when handling installing of this appliance CAUTION Some cabinets and building materials are not designed to withstand the heat produced by the normal safe operation of the appli ance Dis coloration or damage such as delamination may occur To prevent possible damage to cabinets and cabinet finishes use only materials and finishes that will withstand temperature up to 190 F 88 C and that are moisture resistant When cabinets are covered with laminates an appropriate heat resistant adhesive must be used Consult your cabinet manufacturer for proper specifications The cabinet must have solid sides back and bottom The bottom must be solid either at floor level or with the bottom edge of the cutout Any openings around the gas or electrical outlets must be sealed All cabinet openings must be sealed at the time of instal lation to prevent drafts Drafts will affect safe use of the oven TOOLS NEEDED FOR INSTALLATION T handle Angled Tape Screwdriver Wrench
4. Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 or when such standard is not applicable the Standard for Manufactured Home Installations ANSI NCSBCS A225 1 or with local codes where applicable INSTALLATION IN RECREATIONAL PARK TRAILERS The installation must conform with state or other codes or in the absence of such codes with the Standard for Recreational Park Trailers ANSI A119 5 Installation of any gas fired equipment should be made by a licensed plumber A manual gas shut off valve must be installed in the gas supply line ahead of the appliance in the gas stream for safety and ease of service DEBIG 24 SS model only This built in oven is supplied with a protective film on steel and aluminium parts This film must be removed before installing using the appliance WARNING IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE PERSONAL INJURY OR DEATH Y Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance V WHAT TO DO IF YOU SMELL GAS e Do not try to light any appliance e Do not touch any electrical switch do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e If you cannot reach your gas supplier call the fire department vV Installation and service must be
5. any moment and without prior notice without jeopardising the essential functional and safety characteristics of the appliances code 1102635 B8
6. avoid property damage or serious personal injury never use a lighted match If a leak is present tighten joint or unscrew apply more joint compound tighten again and retest connection for leak CONVERSION TO LP PROPANE GAS Every oven is provided with a set of injectors for the various types of gas Select the injectors to be replaced according to the INJECTORS TABLE The nozzle diameters expressed in hundredths of a millimetre are marked on the body of each injector SETTING THE PRESSURE REGULATOR 1 Unscrew the regulator cover 2 Unscrew the A component reverse and screw it according to the LP PROPANE regulation gt an ewoo LP PROPANE NATURAL GAS REGULATION REGULATION INJECTORS TABLE NOMINAL REDUCED LP PROPANE NATURAL GAS POWER POWER 11 W C P 4 W C P injector By pass injector By pass BURNERS ay Bian 1 100 mm 1 100 mm 1 100 mm 1 100 mm Oven burner 11000 1500 96 34 164 adjustable Broil burner 7000 78 130 23 24 OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTORS OF THE OVEN AND BROIL BURNERS a oven burner Lift and remove the lower panel inside the oven Remove the burner securing screw fig 6 6 Withdraw the burner as shown in figure 6 7 and rest it inside the oven Take care no
7. mains connection WARNING check the right positioning of the gas regulator The arrow on the back of the gas regulator must be oriented toward the connector Arrow Fig 6 3 21 22 b Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service company Please provide the service person with this manual before work is started on the oven Gas conversions are the responsibility of the dealer or end user c This oven can be used with NATURAL or LP PROPANE gas It is shipped from the factory adjusted for use with NATURAL gas d Manifold pressure should be checked with a manometer NATURAL gas requires 4 0 W C P and LP PROPANE requires 11 0 W C P see figure below Incoming line pressure upstream from the regulator must be 1 W C P higher than the manifold pressure in order to check the regulator The regulator used on this oven can withstand a maximum input pressure of 1 2 PSI 14 0 W C P If the line pressure is in excess of that amount a step down regulator will be required To oven Manifold test point pressure 1 8 NPT To mains connection Fig 6 4 e The appliance its individual shut off valve and pressure regulator must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of 1 2 PSI 3 5 kPa f The appliance m
8. oven door to the full extent WARNING Risk of explosion The oven door must be open during this operation 2 Lightly press and turn the thermostat knob clockwise to the BROIL position fig 3 4 3 Press the knob right down to prime the electric ignition Keep the knob pressed In case of power cut press the knob and put a lighted match to the right and left side of the burner fig 3 5 Never continue this operation for more than 15 seconds If the burner has still not ignited wait for about 1 minute prior to repeating the ignition 4 Wait about 10 15 seconds after the burner lighting before releasing the knob time of priming of the valve 5 Close the oven door slowly If the flame extinguishes for any reason the safety valve will automatically shut off the gas supply to the burner To re light the burner first turn the oven control knob to position OFF wait for at least 1 minute and then repeat the lighting procedure Do always broil with oven door closed Attention the oven door becomes very hot during operation Keep children away OVEN LIGHT The oven is equipped with a light that illuminates the oven to enable visually controlling the food that is cooking This light is controlled by a switch knob Fig 3 6 To light the oven lamp turn the knob clockwise to position 1 STEP 2 STEP 3 STEP 4 STEP
9. performed by a qualified installer service agency or the gas supplier Aa WARNING NEVER use this appliance as a space heater to heat or warm the room Doing so may result in carbon monoxide poisoning and overheating of the oven This appliance is designed and manufactured solely for the cooking of domestic household food and is not suitable for any none domestic application and therefore should not be used in a commercial environment The appliance guarantee will be void if the appliance is used within a none domestic environment i e a semi commercial commercial or communal environment Dear Customer Thank you for having purchased and given your preference to our product The safety precautions and recommendations reported below are for your own safety and that of others They will also provide a means by which to make full use of the features offered by your appliance Please preserve this booklet carefully It may be useful in future either to your self or to others in the event that doubts should arise relating to its operation This appliance must be used only for the task it has explicitly been designed for that is for cooking foodstuffs Any other form of usage is to be considered as inappropriate and therefore dangerous The manufacturer declines all responsibility in the event of damage caused by improper incorrect or illogical use of the appliance DATA PLATE CONVERSION LABEL
10. then clean the interior of the oven with cloth soaked in water and detergent neutral then dry carefully OVEN BURNER It carries out normal oven cooking The gas flow to the burner is regulated by a thermostat which allow to maintain the oven temperature constant The control of the temperature is assured by a thermostatic probe positioned inside the oven The probe must be always kept in its housing in a clean condition as an incorrect posi tion or encrustment may cause an alteration in the control of the temperature OVEN THERMOSTAT The numbers printed on the control panel fig 3 1 indicate the increasing oven tem perature value F To regulate the temperature set the chosen number onto the knob indicator The position BROIL serves only to turn on the broil burner N B When the oven is not being used set the gas knob to the OFF position and also close the gas shut off valve placed on the main gas supply line IGNITION OF THE OVEN BURNER The thermostat allows the automatic control of the temperature The gas delivery to the oven burner is controlled by a two way thermostatic tap oven and broil burners with flame failure device To light the oven burner operate as follows 1 Open the oven door to its full extent WARNING Risk of explosion The oven door must be open during this opera tion 2 rahe press and turn the thermostat knob anti clockwise fig 3 2 to max position 3 Press the knob right do
11. wrench hexagon key Pencil measure Suitable protective Adjustable Adjustable gloves wrench pliers 16 GENERAL INFORMATION 1 Installation must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI Z223 1 Latest Edition 2 Installation in manufactured mobile home installation must conform with the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 formerly the Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 or when such standard is not applicable the Standard for Manufactured Home Installations ANSI NCSBCS A225 1 or with local codes where applicable 3 Installation in Recreational Park Trailers installation must conform with state or other codes or in the absence of such codes with the Standard for Recreational Park Trailers ANSI A119 5 4 WARNING This appliance shall not be used for space heating This information is based on safety considerations 5 All openings in the wall behind the appliance and in the floor under the appliance shall be sealed 6 Keep appliance area clear and free from combustible materi als gasoline and other flammable vapors 7 Do not obstruct the flow of combustion and ventilation air 8 Disconnect the electrical supply to the appliance before ser vicing 9 When removing appliance for cleaning and or service A Shut off gas at main supply B Disconnect AC power su
12. 0 350 soe 400 dig 50 Fig 1 1 1 4 3 2 CONTROL PANEL Fig 1 1 CAUTION 1 Oven thermostat knob Gas appliances produce heat and humidity in 2 Oven light control knob the environment in which they are installed 3 Cooling fan warning light Ensure that the cooking area is well ventilated 4 Electronic clock electronic alarm following national local codes A mauc AS COOLNGFANWARNNG LIGHT When the cooling fan failure warning light is OFF the cooling fan motor is correctly operating Ele T picts 7 er instruction manual Q The oven can be used i FAN FAILURE When the cooling fan failure warning light is lighted this indicates 1 Close the supply line AY the malfunctioning of the cooling fan motor manual shut off valve el E Disconnect the oven from the gas electrical Shut off valve Ox we mains and contact the After Sales Service Gloss Pesiian FAN AN UNE 2 Disconnect the 3 prong The oven cannot be used ss 3 Contact the After Sales Service electronic clock electronic alarm ELECTRONIC CLOCK fig 2 1 The electronic alarm is a device which groups the functions of 12 hours clock with illu minated display and 10 hours alarm Upon immediate connection of the oven or after a blackout 12 00 will flash on the dis play To set the hour it is necessary to push the button and then within 7 seconds the or button until you have set the exact hour An energy black
13. BUILT IN GAS OVEN for residential use only DeLonghi Models DEBIG 24 SS DEBIG 24 W DEBIG 24 E e USERS OPERATING INSTRUCTIONS e INSTALLATION ADVICE e IMPORTANT PLEASE READ AND FOLLOW IMPORTANT PLEASE READ AND FOLLOW Before beginning please read these instructions completely and carefully Do not remove permanently affixed labels warnings or plates from the product This may void the warranty Please observe all local and national codes and ordinances Please ensure that this product is properly grounded The installer should leave these instructions with the consumer who should retain for local inspector s use and for future reference vy The electrical plug should always be accessible NNN ONAN Installation must conform with local codes or in the absence of codes the National Fuel Gas Code ANSIZ223 1 latest edition Electrical installation must be in accordance with the National Electrical Code ANSI NFPA70 latest edition and or local codes IN CANADA Installation must be in accordance with the current CAN CGA B149 1 National Gas Installation Code or CAN CGA B149 2 Propane Installation Code and or local codes Electrical installation must be in accordance with the current CSA C22 1 Canadian Electrical Codes Part 1 and or local codes INSTALLATION IN MANUFACTURED MOBILE HOME The installation must conform with the Manufactured Home Construction and Safety Standard Title 24 CFR Part 3280 for merly the
14. M REMEMBER TO SETTING THE FREQUENCY OF THE ALARM SOUND The selection from 3 possibilities of sound can be made by pressing the button how to use the gas oven ATTENTION the oven becomes very hot during operation ATTENTION the oven door becomes very hot during operation KEEP CHILDREN AWAY WARNING The door is hot use the handle VERY IMPORTANT The oven broil shall be used always with the oven door closed BAKE amp BROIL OFF l BAKE 200 BROIL 250_ s 300 4 350 550 400 yig 500 Fig 3 1 GAS OVEN SETTING Number printed on the control panel Corresponding Temperature temperature in F in C 200 93 250 121 300 149 350 177 400 204 450 232 500 260 550 288 GENERAL FEATURES The gas oven is provided with two burners a Oven burner mounted on the lower part of the oven 11000 BTU hr b Broil burner mounted on the upper part of the oven 7000 BTU hr USING THE OVEN FOR THE FIRST TIME It is advised to follow these instructions Furnish the interior of the oven by placing the wire racks as described at chapter Cleaning and maintenance Insert shelves and tray Turn the oven on to the maximum temperature position 550 to eliminate possible traces of grease from the oven burner The same operation should be followed for broil burner Switch off the electrical supply let the oven cool down
15. a ny personnel and authorized service personnel Failure to do so can result in death explosion or fire gas connection QO All gas connections must be made according to national and local codes This gas supply service line must be the same size or greater than the inlet line of the appliance Sealant on all pipe joints must be resistant to the action of LP Propane gas The oven is equipped for the use with NATURAL gas It is design certified by CSA International for NATURAL and L P gases with appropriate conversion The model serial rating plate located on the back of the oven has information on the type of gas that can be used If this information does not agree with the type of gas available check with the local gas supplier See page 23 for L P gas conversion inctructions 1 Manual Shut off Valve fig 6 1 The supply line shall be equipped with an approved shutoff valve This valve should be located in the same room as the oven and should be in a location that allows ease of opening and closing in a position where it can be reached quickly in the event of an emergency Do not block access to the shutoff valve The valve is for turning on or shutting off gas to the appliance Shutoff valve open position To oven Gas supply line Fig 6 1 2 Pressure Regulator a All heavy duty commercial type cooking equipment must have a pressure regulator on the incoming service line for
16. ances lemon juice vinegar etc on the surfaces vy Avoid using cleaning products with a chlorine or acidic base The oven must always be cleaned after every use using suitable products and keeping in mind that its operation for 30 minutes on the highest temperature eliminates most grime reducing it to ashes v The use of suitable protective clothing gloves is recommended when handling cleaning this appliance ENAMELLED PARTS v All the enamelled parts must be cleaned with a sponge and soapy water only or other non abrasive products Dry preferably with a chamois leather STAINLESS STEEL PAINTED AND ALUMINIUM PARTS AND SILK SCREEN PRINTED SURFACES y Clean using an appropriate product Always dry thoroughly IMPORTANT these parts must be cleaned very carefully to avoid scratching and abrasion You are advised to use a soft cloth and neutral soap ONLY SOAP WARM WATER MUST BE USED TO CLEAN THE STAINLESS STEEL SURFACES INSIDE OF OVEN This must be cleaned regularly Remove and refit the side runner frames as described on the next chapter With the oven warm wipe the inside walls with a cloth soaked in very hot soapy water or another suitable product Side runner frames lower panel and rack can be removed and washed in the sink OVEN ACCESSORIES INSTALLATION AND REMOVAL Hang up the wire racks G on the oven walls fig 4 1 Slide in on the guides the shelf etc fig 4 2 The rack must be fitted so tha
17. hecked by a qualified electrician to see if it is wired with correct polarity This appliance when installed must be electrically grounded in accordance with local codes Recommended ground method For your personal safety this oven must be grounded This oven is equipped with a 3 prong ground plug To minimize possible shock hazard the cord must be plugged into a mating 3 prong ground type outlet grounded in accordance with the National Electrical Code ANSI NFPA 70 latest edition or Canadian Electrical Code CSA and local codes and ordinances If a mating outlet is not available it is the personal respon sibility and obligation of the customer to have a properly polarized and grounded 3 prong outlet installed by a qualified electrician 3 prong 3 prong polarized ground type outlet ground plug power supply cord ground prong Fig 7 1 ELECTRIC DIAGRAM C 1131550 Electric diagram key Switch Security switch Air switch Oven lamp Cooling fan Electronic clock Ignition switch Ignition coil Thermal overload Cooling fan failure lamp Terminal block Earth connection 27 The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at
18. ing Fig 5 4 CUut out Width S e 55 cut out height 23 minimum height from the floor 22 5 8 574 4 mm Provide hole for electrical connection in this area minimum 7 7 8 200 mm pi Area for electrical connection Gas line opening Provide a suitable hole on the bottom of cutout The centre of hole shall be 10 1 16 255 8 mm from the centre of cutout to the left side and 20 35 64 522 mm from the front corner of cutout to the back Grounded outlet The electric cord with 3 prong ground plug has a length of 48 1220 mm Grounded outlet should be located in an area 7 7 8 200 mm below the bottom of cutout and only on the right side of the cabinet from the centre to the right side of the cabinet A suitable hole has to be provided on the bottom of the cutout in an area posi tioned on the right rear corner 1 1 4 81 8 mm maximum from the right side of cutout and from the rear corner to maximum 20 5 16 515 5 mm from the front corner of cutout to pass the appli ance cable N WARNING Explosion Hazard Use a new CSA or UL approved gas supply line Install a shut off valve Securely tighten all gas connec tions If connected to LP have a quali fied person make sure gas pres sure does not exceed 14 water column Examples of a qualified person include licensed heating per sonnel authorized gas comp
19. mable material in the oven v Make sure that electrical cables connecting other appliances in the proximity of the oven cannot become entrapped in the oven door vZ Do not line the oven walls with aluminium foil Do not place shelves broiler pan pans or other cooking utensils on the base of the oven chamber v The manufacturer declines all liability for injury to persons or damage to property caused by incorrect or improper use of the appliance To avoid any possible hazard the appliance must be installed by qualified personnel only Any repairs by unqualified persons may result in electric shock or short circuit In order to avoid possible injuries to your body or to the appliance do not attempt any repairs by yourself Such work should be carried out by qualified service personnel only vy Important The use of suitable protective clothing gloves is recommended when handling installing or cleaning of this appliance v Danger of burns The oven and cooking accessories may become very hot during operation Make sure children are kept out of reach and warn them accordingly To avoid burns use kitchen clothes and gloves when handling hot parts or utensils Stand away from the oven when opening oven door Hot air or steam which escapes can cause burns to hands face and or eyes y Never clean the oven with a high pressure steam cleaning device as it may provoke a short circuit y This appliance is intended for use in yo
20. our area installation O INSTALLATION TO THE CABINET Taking care NOT to lift the oven by the door handle 4 P ARX This oven may be installed to 24 minimum 609 5 mm wide cabinets Oven dimensions fig 5 1 e width 24 609 5 mm e depth 21 5 8 550 mm e depth 23 3 16 589 5 mm with gas pressure regulator fitted e height 24 609 5 mm e oven frame depth 25 32 20 mm Cutout dimensions fig 5 3 e width 22 559 mm e depth 23 584 mm minimum from front corner of cutout e height 23 584 IMPORTANT NOTE THE BOTTOM OF CUTOUT SHALL BE AT LEAST 22 5 8 574 4 mm FROM THE FLOOR DO NOT INSTALL THE OVEN BENEATH THE WORK COUNTER On the lover side the oven must lay on a support standing the oven weight Oven support surface MUST be solid All openings in the wall or floor where the oven is to be installed MUST be sealed Oven location should be away from strong draft areas such as windows doors and strong heating vents For SAFETY CONSIDERATIONS the oven SHALL BE FAS TENED to the cabinet with four 4 SUITABLE screws not supplied with the unit through the holes in the trim see fig 5 2 The unit should be leveled properly before being secured to the cabinet 24 609 5 mm 22 11 64 563 2 mm 17 18 Fig 5 3 Provide a hole for gas connection to 1 2 diameter pipe fitt
21. out makes the clock go to zero SET TIME OF DAY Fig 2 1 Push button and then within 7 seconds the A or button until you have set the exact hour This function remains activated 7 seconds after the last pushing of A or button Change the hours only press the button for 4 seconds until the hours display will flash Change the hours only by pushing the A or button The minutes and hidden sec onds will not be affected ELECTRONIC ALARM The alarm program consists only of a buzzer which may be set for a maximum period of 10 hours To set the time push the or button until you obtain the desired time in the dis play From 0 10 to 99 50 you read the time in minutes and seconds 10 seconds step then from 1 40 to 10 00 you read the time in hours and minutes minutes step Having finished the setting the symbol will be lighted and the countdown will start immediately During countdown the timer has priority in the display To show the time of day press button At the end of the time the symbol will be switched off and an intermit tent buzzer during 7 minutes will go off this can be stopped by pressing the but ton The signal will be skipped if button is pressed during the last 15 seconds of the timer To stop the alarm countdown in any moment keep the button pressed until you read 0 00 on the display symbol A switches off IMPORTANT WARNING THIS IS ONLY AN ELECTRONIC ALAR
22. pply C Disconnect gas line to the inlet pipe D Carefully lift appliance out of cabinet cutout CAUTION Use care in handling 10 Electrical Requirement Electrical installation should comply with national and local codes 11 Air Supply and Ventilation The installer must refers to local national codes 12 Gas Manifold Pressure Natural gas 4 0 W C P LP Propane 11 0 W C P 13 The misuse of oven door e g stepping sitting or leaning on them can result in potential hazards and or injuries WARNING ELECTRICAL GROUNDING INSTRUCTIONS The oven must be electrically grounded in accordance with local codes or in the absence of local codes with the National Electrical Code ANSI NFPA No 70 latest edition Installation should be made by a licensed electrician FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED This appliance is equipped with a three prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded socket Do not cut or remove the grounding prong from the plug For personal safety this appliance must be properly grounded Do not under any circumstances cut or remove the third ground prong from the power plug REPLACEMENT PARTS Only authorized replacement parts may be used in performing service on the oven Replacement parts are available from factory authorized parts distributors Contact the nearest parts distributor in y
23. rs fig 4 6 Insert the hinges in their position until levers H are hooked Open the door completely to obtain the release of levers L 13 14 DO S AND DO NOT S e Do always broil with the oven door closed e Do read the user instructions carefully before using the oven for first time e Do allow the oven to heat for one and a half hours before using for the first time in order to expel any smell from the new oven insulation without the introduction of food e Do clean your oven regularly e Do remove spills as soon as they occur e Do always use oven gloves when removing food shelves and trays from the oven e Do not allow children near the oven when in use e Do not allow fat or oils to build up in the oven base or oven accessories e Do not place cooking utensils or plates directly onto the oven base e Do not broil without using the broiler pan e Do not place hot enamel parts in water Leave them to cool first e Do not allow vinegar coffee milk saltwater lemon or tomato juice to remain in contact with enamel parts i e inside the oven e Do not use abrasive cleaners or powders that will scratch the surface of the stainless steel and the enamel e Do not attempt to repair the internal workings of your oven e DEBIG 24 SS model only Do remove the protective film before the first use e Fire risk Do not store flammable material in the oven
24. safe and efficient operation since service pressure may fluctuate with local demand Before installing the regulator mount the 3 8 NPT conical male connector to the regulator see picture 6 2a Gasket supplied have to be placed between 3 8 NPT conical connector manifold male pipe fitting See picture 6 2b The regulator supplied with this oven must be installed before any gas connections are made Use supplied pressure regulator only 19 20 PRESSURE REGULATOR INSTALLATION STEP 1 Mount the 3 8 NPT conical male connector to the pressure regulator and tighten by using a wrench Do not over tighten the connector Over tightening may crack regulator Fig 6 2a STEP 2 Assemble the 3 8 NPT connector pressure regulator group to the manifold interposing the gasket supplied The regulator cover must be oriented toward the back of the cabinet IMPORTANT use two spanners to tighten the connection Regulator cover Fig 6 2b GAS CONNECTION SPECIFICATION Manifold male pipe fitting 3 8 NPT conical male Oven manifold 1 2 G cylindrical ISO 228 1 male 1 2 G cylindrical ISO 228 1 female Pressure regulator Connector 3 8 NPT female 3 8 NPT female To oven Manifold ts i test point Ni Ligh ist pressure Mes 1 8 NPT To
25. t to damage the wire to the ignition electrode and the safety valve probe Using a 7 mm box spanner unscrew the injector indicated by the arrow in fig 6 7 and replace it by the proper one according to the kind of gas Then replace the burner repeating the above steps in reverse order b broil burner Remove the burner by unscrewing the front screw fig 6 8 Gently suspend the burner as shown in figure 6 9 Be careful not to damage the wire of the electric ignition and the probe of the safety valve Using a 7 mm box spanner replace the injector indicated by the arrow in fig 6 9 by the proper one according to the kind of gas Replace the burner repeating the above steps in reverse order ADJUSTMENT OF THE OVEN BURNER MINIMUM This needs to be done only for the oven burner the broil is a fixed capacity by acting on the thermostat in the following way Turn on the burner by setting the thermostat knob on position 550 Remove the knob and unscrew the by pass screw G fig 7 12 about three times by passing a small flat screwdriver 3 mm blade 100 mm length through the panel opening Re mount the knob and let the oven heat up for about 10 minutes then bring the knob to position 200 minimum to operate the thermostat by pass After having removed the knob again and being very careful not to turn the tap rod slowly screw the by pass screws G fig 6 10 until you ob
26. t the safety catch which stops it sliding out faces the inside of the oven Position the broiler pan above the oven shelf To dismantle operate in reverse order OVEN DOOR The internal glass of the oven door can be easily removed for cleaning by unscrewing the two lateral fixing screws fig 4 3 Do not store flammable material in the oven REPLACING THE OVEN LIGHT Before any maintenance is started involving electrical parts of the appliance it must be disconnected from the power supply Let the oven cavity and the broil burner cool down Switch off the electrical supply Remove the protective cover Unscrew and replace the bulb with a new one suitable for high temperatures 300 C 570 F having the following specifications 120V 60 Hz 15W E14 Refit the protective cover NOTE Oven bulb replacement is not covered by your guarantee REMOVING THE OVEN DOOR To facilitate oven cleaning it is possible to remove the door Please follow the instructions carefully Open the door completely Push down the lever L and keeping it in this position slowly close the door in order to block the hinge fig 4 4 Grip the door as indicated in fig 4 5 and while closing it release the two hinges as shown in fig 4 6 Rest the door on a soft surface DOOR ASSEMBLY Grip the door with your hands placed near the hinges and raise the levers H with your forefinge
27. tain a flame of 3 4 mm in height N B For LP PROPANE gas the by pass screw must be fixed thoroughly After regulation repeat the operations indicated in paragraph 2 Pressure regulator at page 19 If the oven has been disconnected and then connected again to the gas supply line repeat the operations indicated in paragraph 5 Leak Testing at page 23 IMPORTANT After conversion to LP PROPANE gas has been carried out affix near the data plate the conversion label supplied and also affix a conversion label at page 3 of this instruction manual 25 4 amp WARNING 4 Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove ground prong Do not use an adapter Failure to follow these instructions can result in death fire or electrical shock WARNING VERY IMPORTANT Before any operation of maintenance disconnect the appliance from the electrical mains supply electrical connection If codes permit and a separate ground wire is used it is recommended that a qualified electrician determine that the ground path is adequate Check with a qualified electrician if you are not sure whether the oven is proper ly grounded Do Not ground to a gas pipe A 120 volt 60 Hz AC only 15 ampere fused electrical supply is required A time delay fuse or circuit breaker is recommended It is recommended that a separate circuit serv ing only this appliance be provided The outlet must be c
28. ur household Never use the appliance for any other purpose y If you should decide not to use this appliance any longer or decide to substitute an older model before disposing of it it is recommended that it be made inoperative in an appropriate manner in accordance to health and environmental protection regulations ensuring in particular that all potentially haz ardous parts be made harmless especially in relation to chil dren who could play with old appliances Remove the door before disposal to prevent entrapment WARNING This appliance shall not be used for space heating This information is based on safety considerations y Keep appliance area clear and free from combustible materi als gasoline and other flammable vapors v The misuse of oven door e g stepping sitting or leaning on them can result in potential hazards and or injuries IMPORTANT PRECAUTIONS AND RECOM MENDATIONS FOR USE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamental rules In particular Never touch the appliance with wet hands or feet v Do not operate the appliance barefooted v Do not allow children or disabled people to use the appliance without your supervision The manufacturer cannot be held responsible for any damages caused by improper incorrect or unreasonable use of the appliance control panel BAKE amp BROIL OFF BAKE 200 250_ 30
29. ust be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1 2 PSI 3 5 kPa 3 Flexible Connections If local codes permit CSA design certified flexible metal appliance connector is recommended for connecting this oven to the gas supply line Do Not kink or damage the flexible connector when moving the oven The pressure regulator has 3 8 NPT female pipe threads You will need to determine the fittings required depending on the size of your gas supply line flexible metal connector and shutoff valve 4 Rigid Pipe Connections If rigid pipe is used as a gas supply line a combination of pipe fittings must be used to obtain an in line connection to the oven All strains must be removed from the supply and fuel lines so oven will be level and in line e Use joint compounds and gaskets that are resistant to action of natural or propane gas on all male pipe threads e Do not over tighten gas fitting when attaching to pressure regulator Over tightening may crack regulator 5 Leak Testing IMPORTANT Leak testing of the appliance shall be conducted as follows e After final gas connection is made turn on manual gas valve and test all connections in gas supply piping and appliance for gas leaks with a soapy water solution During this test all appliance gas valves have to be closed e In order to
30. wn to prime the electric ignition Keep the knob pressed In case of power cut press the knob and immediately approach a lighted match to the opening A fig 3 3 Never continue this operation for more than 15 seconds If the burner has still not ignited wait for about 1 minute prior to repeating the ignition 4 Wait about 10 15 seconds after the burner lighting before releasing the knob time of priming of the valve 5 Close the oven door slowly and adjust the burner according to the power required If the flame extinguishes for any reason the safety valve will automatically shut off the gas supply to the burner To re light the burner first turn the oven control knob to position OFF wait for at least 1 minute and then repeat the lighting procedure Attention the oven door becomes very hot during operation Keep children away OVEN COOKING Before introducing the food preheat the oven to the desired temperature For a correct preheating operation it is advisable to remove the tray from the oven and introduce it together with the food when the oven has reached the desired tempera ture Check the cooking time and turn off the oven 5 minutes before the theoretical time to recuperate the stored heat 10 Fig 3 6 LIGHT OFF IGNITION OF THE BROIL BURNER The broil burner generates the infra red rays for broiling To light the broil burner operate as follow 1 Open the
Download Pdf Manuals
Related Search