Crimestopper Security Products CS-865RKE Automobile Alarm User Manual
Contents
1. CS 865RKE Series REMOTE KEYLESS ENTRY SYSTEM INSTALLATION amp OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products Inc This booklet contains the information necessary for installing and operating your system If any questions arise contact your installation dealer or Crimestopper Security Products Inc at the Tech Support number below IMPORTANT INFORMATION Primary and Optional Features PRIMARY FEATURES These are features that must be connected in order for the system to operate properly i e Power amp Ground along with the Primary features of Power Locks amp Flashing Lights OPTIONAL FEATURES Optional features are connected only if desired or agreed upon by the installing dealer i e Driver s Separate Unlock Horn Chirp Dome light illumination Trunk Pop etc These features may require additional parts and labor charges Consult with your installer and come to an agreement about your optional features before installation NOTE The LED is required for programmable options See page 10 TECH SUPPORT This device complies with FCC Rules part 15 Operation is subject to the Mon Fri 8 00 AM 4 30 PM Pacific Time following two conditions 1 This device may not cause interference and 2 800 998 6880 this device must accept any interference that may be received including interference that may cause unde2. Option Option Description Selection Lock Button Unlock Button 1 Auto Lock amp Unlock with ON or OFF ON OFF Ignition 2 Double Unlock Pulse ON or OFF OFF ON 3 Horn Chirp ON or OFF ON OFF 4 Lock Unlock Pulse Time 0 8 Sec or 3 Sec 0 8 Sec 3 Sec 5 Passive Starter Lock amp ON or OFF OFF ON Disable 6 Ignition Trigger ON or OFF OFF ON T Extended Horn Chirp Normal or Normal Extended Extended PROGRAMMABLE OPTION DESCRIPTIONS 1 AUTOLOCK UNLOCK WITH IGNITION Controls whether the doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off Note When Separate Driver s Door Unlock feature is installed only driver s door will unlock when IGN is turned off 10 OPTION PROGRAMMING cont 2 DOUBLE UNLOCK PULSE The unit will send 2 unlock pulses when the 2 Unlock button is pressed This feature may be required for interfacing this system into specific makes and models of vehicles that require this function 3 HORN CHIRP CONFIRMATION This option turns the horn chirps for lock unlock on or off 4 DOOR LOCK UNLOCK PULSE TIME Controls the amount of time 0 8 sec or 3 sec for the lock unlock pulse The 3 sec setting may be required for 1980 90 s European Vehicles that require a long pulse to operate electric vacuum type door lock systems 5 PASSIVE LOCK amp STARTER DISABLE Starter disable feature OPTIONAL When this option is turned ON the unit will PASS
3. WHITE BLACK X NOT USED BLUE BLACK VIOLET BROWN BLACK GREEN BLACK VIOLET BLACK WHITE BLACK LOCK WIRE CS 865RKE SEPARATE DRIVER S DOOR UNLOCK DIAGRAMS DRIVER PRIORITY UNLOCK with NEGATIVE TYPE DOOR LOCKS VIOLET VIOLET BLACK BLUE WHITE FUSED 12V WHITE BLACK X NOT GREEN BLACK BROWN BLACK BLUE BLACK DRIVER S DOOR MOTOR n ES FACTORY LOCK im RELAYS e UNLOCK WIRE CUT DRIVER PRIORITY UNLOCK with REV POLARITY DOOR LOCKS VIOLET VIOLET BLACK BLUE WHITE GREEN BLACK WHITE BLACK BROWN BLACK BLUE BLACK MASTER SWITCH DRIVER S DOOR MOTOR L ju a UNLOCK WIRE JUMPER PIN DIAGRAM The jumper plugs inside the control module determine the unit s 12V or Negative Parking amp Dome Light Relay outputs White amp Black White wires Use the jumper pins to change the Positive or Negative Polarity of the outputs as required for your particular installation Default Positive for Parking Light and Negative for Dome Light See diagram below CS 865RKE II MODULE JUMPER SIDE VIEW JUMPER PLUG JUMPER PINS TOP VIEW OF JUMPER PINS Parking Light P4 Dome Light P5 NEG PARKING LIGHT 12V DOME LIGHT 12V PARKING LIGHT NEG DOME LIGHT DEFAULT DEFAULT SYSTEM WIRING DIAGRAM 6 PINDOOR LOSK Perse REGOLE a HARNESS HARNESS y Open Terminal 87 On Boa
4. 7 8 seconds When going into VALET you will get 1 horn chirp 1 light flash and LED will be on SOLID When coming out of VALET mode you will get 2 Chirps 2 Flashes and LED will go out The Optional Starter Disable feature if installed will not operate when in VALET mode 13 OPERATION EMERGENCY OVERRIDE MAY BE NEEDED WHEN OPTIONAL STARTER DISABLE INSTALLED If you have lost the transmitter or it stops working for any reason and the system was locked with the remote Emergency Disarm is needed to override the Starter Disable circuit Open the door with the key manually turn the ignition on and press the override program button for 7 8 seconds You will get 1 short horn chirp and 1 light flash which will put the system into VALET mode If Optional LED light is installed it will turn ON and stay on solid while in VALET mode AUTO LOCK UNLOCK WITH IGNITION The doors will automatically lock when the ignition is turned on and will unlock when the ignition is turned off If this is not desired see the Option Programming section on page 10 to change this feature HORN HONK CHIRP FEATURE OPTIONAL This system can provide short chirps of your Factory Car Horn along with the Flashing Parking lights for Lock Unlock confirmation This optional feature requires additional installation Once installed the horn chirp feature can also be turned ON or OFF in the Option Programming Section See Page 10 DOME LIGHT ILLUMINATION OPTIONAL
5. This feature turns on the vehicles dome light upon disarm for 30 seconds or until the key is inserted and turned on This will provide illuminated entry to your vehicle at night or in dimly lit areas for safety and security This feature requires additional installation 14 2 VEHICLE OPERATION SETUP Your CS 865RKE remote can be programmed to operate a second vehicle with another CS 865RKE II system installed Setup is required order to use 2 vehicle operation You have to learn your remote to the second vehicle Reference the transmitter programming instructions on page 9 of this manual Perform the transmitter programming steps at the second vehicle In step 3 you must re learn the second vehicles own remotes press the side button on your remote and then the Lock button on your remote OPERATION After setup is complete you can operate the second vehicle from your remote control Press the side button on your remote first and within 3 seconds press any of the 4 function buttons on your remote to control vehicle 2 You can keep pressing function buttons to control vehicle 2 as long as it is within the 3 second window After 3 seconds have elapsed the remote will revert back to Car 1 control Press for Vehicle 2 NOTE CS 865RKE Il Remote Controls ARE NOT compatible with previous CS 865 855 or 845 Remote Keyless Entry Systems 15 CRIME 319 2 2 3 www crimestopper com ernie tom ONLIN
6. 7 BLUE WHITE WIRE PASSENGER S DOOR UNLOCK OUTPUT Optional requires relay Connects to unlock circuit for passenger door s when using separate driver s door unlock option See DOOR LOCK WIRING for configuration options WHITE RED WIRE AUXILIARY REMOTE OUTPUT 2 Optional requires relay This wire provides a Negative momentary output for activation of optional or auxiliary devices lt is controlled by Pressing and Holding Button 1 Lock 3 ORANGE WIRE NEGATIVE ARMED OUTPUT This wire provides a constant GROUND output when system is locked with the remote transmitter This output can used for a starter disable relay or a device such as a window roll up module See System Wiring Diagram On page GRAY WIRE AUXILIARY REMOTE OUTPUT 1 Optional requires relay Negative Pulsed output controlled by pressing Button 3 Trunk Symbol for at least 1 second BROWN WHITE HORN HONK CHIRP OUTPUT Optional requires relay This wire provides a negative pulse output to honk chirp the factory horn for audible lock unlock confirmation Connect Brown White to terminal 85 of a relay Connect terminal 86 to 12V Constant Connect terminal 87 to 12V or GROUND depending on the type of horn activation circuit in the vehicle Connect terminal 30 to the horn activation circuit NOTE Many vehicles use a Negative type of horn circuit however we recommend that you test the circuit on your vehicle before making any connections to avoid any possib
7. E TECHNICAL SUPPORT EA US Se Cocco www crimestopper com techweb03 html 2003 Crimestopper Security Products
8. IVELY lock and activate the Starter Disable output 20 seconds after the ignition is turned off 6 IGNITION TRIGGER This option controls the unit s optional Ignition trigger feature If selected to ON then the vehicle s horn will honk if an unauthorized operator turns on the Ignition after the vehicle had been locked with the remote This function is similar to an alarm system To avoid a trigger use the remote for BOTH LOCKING and UNLOCKING the vehicle If system accidentally triggers press button 4 to reset 7 EXTENDED HORN CHIRP This option allows the unit to provide a slightly longer lock unlock horn chirp output This option is ONLY required on specific vehicles where the normal horn chirp is not long enough to activate the factory horn and produce a chirp OPTION RESET OPTION RESET RESTORES PROGRAMMING OPTIONS TO FACTORY DEFAULT SETTINGS 1 Turn the Ignition ON wait one second and press the Override Program button 5 times 2 The system will flash the LED 5 times 3 Press Button 3 Trunk Lights will flash 4 times and horn will chirp if optional horn chirp installed 4 times All options will be returned to factory default setting Default settings are marked with an 7 11 OPERATION 2 UNLOCK 1 LOCK FLASHLIGHT VEHICLE 2 3 TRUNK AUX 4 REMOTE LOCK To lock the doors press the 1 Lock Symbol button on the transmitter Lights will flash once and LED will begin flashing You will also h
9. ear a single horn chirp if optional horn chirp feature is installed Optional If starter disable is installed it will also become active REMOTE UNLOCK To unlock the doors press the 2 Unlock Symbol button on the transmitter Lights will flash 2 times You will hear 2 horn chirps if horn chirp installed Optional Starter disable will turn off SEPARATE DRIVER S DOOR UNLOCK OPTIONAL When using the Optional Separate Driver s amp Passenger unlock also known as Driver s Priority or 2 Stage unlock press the 2 Unlock button once to unlock the driver s door and a second time to unlock remaining door as needed Lights will flash 2 times on the first press and then one more time on the second press Separate drivers door unlock usually requires additional parts and labor to install over standard all doors unlock 12 OPERATION REMOTE PANIC PROTECTION OPTIONAL REQUIRES HORN HONK FEATURE To sound the panic alarm in an emergency situation or to draw attention to your vehicle press and hold Button 4 Panic for at least 2 seconds The horn will begin to pulse and parking lights will flash for up 45 seconds or until the Panic Button on the transmitter is pressed again to reset this mode TRUNK HATCH POP REMOTE AUX OUTPUT 1 OPTIONAL To pop the trunk Optional press Button 3 Open Trunk Symbol on the transmitter for at least 2 seconds There is a slight delay on this function This is an intentional delay to help prevent
10. es of this unit LED Optional The optional Red LED provides a useful theft deterrent The LED blinks after you lock the vehicle with your remote simulating an alarm system The LED is also used when programming options you decide to install the LED choose a visible location in the dash or console for a location WHITE WIRE 12V or NEGATIVE PARKING LIGHT Jumper Selectable On Board Relay 10A Connect to switched 12V parking light wire at back of light switch If this is not possible connect directly to one of the parking lights at the front of the vehicle If your vehicle requires a Negative Ground signal to activate the parking lights then you have to open the control and move the jumper located on the circuit board inside the unit For European vehicles with separate right and left circuits use a dual relay or 2 diodes to separate the output signal The DEFAULT output is POSITIVE SEE PAGE 7 BLACK YELLOW WIRE AUXILIARY REMOTE OUTPUT 3 Optional requires relay This wire provides a Negative momentary output for activation of optional or auxiliary devices lt is controlled by Pressing and Holding Buttons 2 Unlock and 4 Panic together BLACK WHITE WIRE NEG or 12V DOME LIGHT Jumper Selectable On Board Relay 10A Connect to dome light activation circuit for Negative type circuits For Positive type circuits open the control module and move the jumper the plug as shown in illustration The DEFAULT is NEGATIVE SEE PAGE
11. le damage GREEN WIRE NOT USED No Connection YELLOW WIRE IGNITION SWITCHED ON AND START 12 VOLTS Connect to an ignition wire that shows 12 Volts when the key in both On and Start positions BLACK WIRE SYSTEM CHASSIS GROUND THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE Scrape away any paint or dirt from the connection point to ensure a good connection Keep ground wire short RED WIRE 12V POWER INPUT 15 amp fuse Connect to 12 Volt source with supplied fuse amp holder Recommended location for this connection is at the vehicle battery positive terminal POWER DOOR LOCK WIRING 6 PINDOOR LOCK OUTPUT PLUG On Board Relays VIOLET Fused 10A UNLOCK Normally Open Terminal 87 On board Unlock Relay BROWN BLACK UNLOCK Normally Closed Terminal 87A On board Unlock Relay BLUE BLACK UNLOCK Output Terminal 30 On board Unlock Relay VIOLET BLACK Fused 10A LOCK Normally Open Terminal 87 On board Lock Relay WHITE BLACK LOCK Normally Closed Terminal 87A On board Lock Relay GREEN BLACK LOCK Output Terminal 30 On board Lock Relay 4 POWER DOOR LOCK WIRING NEGATIVE TRIGGER DOORLOCK WIRING BLUE BLACK VIOLET BROWN BLACK X NOT USED GREEN BLACK VIOLET BLACK WHITE BLACK USED BLUE BLACK VIOLET BROWN BLACK GREEN BLACK VIOLET BLACK WHITE BLACK Master Switch LOCK WIRE POSITIVE TRIGGER DOORLOCK WIRING BLUE BLACK VIOLET BROWN BLACK x NOT USED GREEN BLACK VIOLET BLACK
12. ll components to be placed These components include the module itself valet program button and possible relays Allow enough wire to create a service loop with strain relief should servicing be required DAMAGE resulting from incorrect installation or failure to follow guidelines stated in this book will not be covered under warranty and subject to repair or replacement charges USE A VOLT OHM METER to test and locate all connections Test Lights can damage a vehicle s computer systems ADDITIONAL PARTS which are not included with this unit may be needed for your particular vehicle These items may include extra relays Part CS 402A or Special Data Bus interface modules DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake and gas pedals steering column or any other moving parts in the vehicle z REMOVE MAIN SYSTEM FUSE S before jump starting the vehicle or charging the vehicles battery COMPONENT MOUNTING CONTROL MODULE Locate the module underdash as high as possible Driver s Side usually provides an easy location for the majority of the wiring connections The antenna wire should be routed away from any metal if possible DO NOT alter the length of the antenna wire or ground the antenna wire OVERRIDE PROGRAM BUTTON Mount the button in a hidden but accessible location It is used for emergency disarm when optional starter disable is installed without the use of the transmitter and for programming featur
13. n 1 Lock on the remote you wish to program 4 You should get 1 light flash Press button 1 of a second transmitter the unit will flash 2 times Press the lock button on a 3 or 4 transmitter for up to 4 total Note The unit will not flash the lights when learning the 4 code Turn key off to exit programming mode i IGN OFF S gt gt WAIT FOR 4 FLASHES PRESS 4X s p gt IGN OFF LIGHTS FLASH 2 3 or 4 X s PRESS LOCK BTN OPTION PROGRAMMING To change programmable options follow steps below 1 Turn the Ignition ON and press the Override Program button 5 times 2 The parking lights will flash 5 times and status LED will be on solid 3 Within the next few seconds press the Override Program button again the number of times that corresponds to the options chart below Parking lights and or optional horn should chirp for each button press Don t lose count 4 When you get to the desired option number quickly press the appropriate button on the remote control according to the chart below The system will provide 1 chirp flash for Button 1 Lock Symbol and 2 chirps flashes for button 2 See Option Chart for numbers descriptions and values 5 Turn Ignition off Change one option at a time repeating these same steps 1 4 When you are finished customizing options check operation to see if the option s have changed PROGRAMMING OPTIONS CHART DEFAULT SETTING
14. rd Unlock Relay l BROWN BLACK UNLOCK Normally Closed Terminal 87A On Board Unlock Relay OVERRIDE BLUE BLACK lt UNLOCK Gerd Ora poa i E 2 PIN RED HARNESS WHITE BLACK LOCK Normally Closed Terminal 87A On Board Lock Relay LED VIOLET BLACK OPTIONAL LOCK Normally Open Terminal 87 On Board Lock Relay gt Parking Lights E 12V or Neg Parking Light WHITE CS 865RKE Module 12V or Parking Light Output Output On board 10A Relay mmi 12 PIN MAIN HARNESS BLACK WHITE 12V or Neg Dome Light BLUE WHITE Output On board 10A Relay MAIN DOORLOCK PROGRAM HARNESS HARNESS BUTTON WHITE RED Passenger Unlock Ouput ORANGE Press UNLOCK Button a Negative Armed Output 2nd Time for 2 Step Unlock AUX OUTPUT 2 RED 12V Power Input Negative Trunk Pop Output AUX 1 GRAY K BROWN WHITE Negative Horn Output NOT USED GREEN BLACK Chassis ound BATTERY FUSE START WIRE YELLOW Box IGN OPTIONAL 12V Ignition Input SW STARTER DISABLE WIRING Relay not included 8 CS 865RKE II TRANSMITTER PROGRAMMING NOTE All transmitters must be learned at the time of programming This system can learn up to 4 remotes 1 Turn key to the ON position and press program button 4 times 2 After a short delay the unit will flash the parking lights 4 times 3 Press the Butto
15. sired operation The manufacturer is not www crimestopper com responsible for any radio or TV interference caused by unauthorized email crimestopper com modification to this equipment Such modification could void the user s authority to operate the equipment REV B 03 2004 TABLE OF CONTENTS Pre Installation amp Component 2 3 E E E E 3 4 Power Door LOCK 2 4 6 Jumper Diagram EAE 7 System Wiring Diagram ii is iets as exea eus Ap Vena ea is nh AAA EEEE AAAA EEUE T EEEa Doe Seca see EANN Aar see 8 Transmitter Programming euius oue pened sen ER EEUU FERA 9 Option Programming Option rsen enhn nnn 10 11 InstFUCTIOTS ee tt eon as ata saree ne ohio cem auc vad shee aber d aptas peas 12 14 2 xu eene ita kasi e addu Siro eot ceu E TA Oe 15 PRE INSTALLATION CONSIDERATIONS To ease installation we suggest that you READ THIS MANUAL before beginning your installation BEFORE BEGINNING check all vehicle manufacturer cautions and warnings regarding electrical service AIR BAGS ABS BRAKES ENGINE BODY COMPUTER AND BATTERY PLAN OUT YOUR INSTALLATION and determine most suitable locations for a
16. your trunk or hatch from opening accidentally when the remote is in your pocket or purse FLASHLIGHT FUNCTION Press the upper side button the remote control to activate the convenient Flashlight feature using the remote s High Power Blue LED indicator 2 AUX OUTPUT REMOTE AUX OUTPUT 2 OPTIONAL To activate the Second auxiliary output press and hold Button 1 Lock and hold for more than 1 second This output can be used to control other optional add on accessories such as a Remote Engine Start Module 3 AUX OUTPUT REMOTE AUX OUTPUT 3 OPTIONAL To activate the Third auxiliary output press and hold Buttons 2 Unlock and 4 Panic together This output can be used additional accessories IGNITION TRIGGER OPTIONAL REQUIRES HORN HONK FEATURE This optional feature allows the unit to activate the panic mode if an unauthorized operator turns the Ignition ON after the vehicle had been locked using the remote control This is not alarm system that can be triggered when opening the door however with this feature is will trigger if the Ignition is turned on if you choose To avoid an Ignition trigger use the remote for BOTH LOCKING and UNLOCKING the vehicle When the Ignition trigger occurs press button 2 Unlock on the remote or if you don t have a remote then perform an Emergency Override See Below for Emergency Override VALET MODE To get in and out of VALET mode turn the ignition on and press the override program button for about
Download Pdf Manuals
Related Search