Clifford 50 Automobile Alarm User Manual
Contents
1. efficient than scanning see above Unlike scanners that sequentially transmit one digital code after another hoping one of them is the correct code to disarm the alarm a process that may take hours days or even years depending on the alarm s number of codes code grabbers literally record from hundreds of feet away the code sent by your car alarm remote control A code grabber will instantly duplicate any remote control code even 1f the remote has billions or trillions of codes The thief simply waits for you to arm your alarm with the remote control and walk away Then he plays back the code instantly disarming your car s alarm and unlocking the doors It s like giving the thief your car keys All non Clifford alarms can be defeated that easily In contrast Concept systems use complex digital signal processing and unbreachable encryption to randomly change the digital code every time you use the remote Your remote will never transmit the same code Thus the code recorded and played back by the thief s code grabber will never be accepted by your Concept 50 Only ACG can make a car alarm impervious to code grabbing and only Clifford systems have ACG with Random Code Encryption Smart AutoArming If this feature is enabled and you forget to remotely arm your Concept 50 it arms itself auto matically passively 30 seconds after the doors are closed For your convenience if you re open any door within the 30 sec countdown Auto2. seconds later there will be 4 chirps and 4 flashes NOTE Since this is a warning indication you will hear the 4 chirps even if you have the chirp muting feature turned on W Specific malfunction identification The system can also indicate the specific trigger or sensor that is malfunctioning This feature saves you time and money since your installer won t have to spend hours trying to determine where the problem is If you receive the 4 chirp 4 flash signal upon remote disarming perform the following to identify the malfunctioning trigger or sensor 1 Remotely disarm then turn on the ignition The LED status indicator inside the vehicle will be flashing pause then repeat 2 Count the number of blinks in one cycle between pauses for your convenience the blink cycle repeats a total of 5 times and refer to the chart below Number of LED blinks between pauses Malfunction 1 blink Magnetic Resonance Sensor 2 blinks Glass tampering sensor 3 blinks Door trigger 4 blinks Trunk trigger 5 blinks Hood trigger 6 blinks Proximity Sensor or other optional sensor Automatic malfunction bypass To provide the utmost protection even if a system component malfunctions your Concept 50 will automatically bypass any faulty point and arm all other triggers and sensors until you can have the system serviced by your local Authorized Dealer 15 Multiple event TotalRecall The system s non vol
3. sensitivity activate the headlights control Remote QuickAccess features or command options such as remote trunk release remote memory seat adjustment and even remote starting of the engine and heater or air conditioner among other available options How to use your keychain LED indicator A Button f remote control A Y our remote control can individually command up preme nn to 12 different system functions and options It s like having a TV with 12 channels You change channels functions with your keychain remote control But instead of putting 12 buttons on the remote control we made it easy First the button you use the most button 1 to arm disarm lock and unlock the doors is larger than the others Buttons 2 3 and 4 are the smaller buttons to the right below and left of button 1 The LevelShift button on the side permits you to select channels 5 12 with the same four buttons W To transmit either channel 1 2 3 or 4 Just press either button 1 2 3 or 4 For instance to transmit channel 3 press button 3 While you transmit the LED indicator will blink once every second this indicates level 1 E Jo transmit either channel 5 6 7 or 8 Press the LevelShift button once This shifts buttons 1 4 to level 2 channels 5 8 Then press the desired button within the next 7 seconds For instance to transmit channel 5 press the LevelShift button once then press button 1 While you transmit you ll notice th
4. settings of three different features It s so easy you could even do it while driving To set all three features back to their factory settings just repeat steps 1 5 Adding new remote controls For other drivers in your family or if you wish to control Concept systems on your other cars with the same remote control you can buy additional remote controls from any Authorized Clifford Dealer or call our 24 hour Customer Service Department at 800 824 3208 and program them into the system yourself Each Concept 50 will respond to as many as four 12 channel remote controls To add a new remote control to the system use the procedures noted in the User selectable features section on pages 19 21 How to erase the codes of lost or stolen remote controls If one of your remote controls is ever lost or stolen you can erase its digital codes from the system memory to make sure that the missing remote control can never be used to disarm your system To do so use the Erase all channels feature feature column 2 row 6 on the Matrix of user selectable features on pages 20 21 This will clear all remote control codes from the system memory Then simply program each remaining and or replacement remote control as noted in the Adding new remote controls section above O Copyright Clifford Electronics Inc 1994 31 070D C500M 194
5. 20 seconds after you switch on the ignition and press the brake or open a door while the engine is running you must enter your secret disarming code to let the system know it is you who is driving Your code will be a 1 to 3 digit number of your choosing Each digit can be any number from 1 to 9 i e the code can be any number between 1 and 999 except those that contain a Zero Currently your system s factory set disarming code is the single digit 2 IMPORTANT What you MUST do to drive your car Until you set your own secret disarming code you will use the factory set disarming code which is the single digit 2 To drive your car do the following 1 Start the engine then press and release the brake pedal 2 Within 20 seconds enter the factory set code via the rocker switch mounted on your vehicle s dashboard or console you can do this while driving a To enter the factory set disarming code of 2 tap the momentary spring loaded side of the PlainView switch twice b Press the PlainView switch to its other side latched side then return the switch to its center position You may continue driving NOTE If you wish you may select to use a remote control button sequence to disengage the anti carjacking countdown A dedicated disarming remote not carried on your keychain is also available See pages 19 21 for information What you MUST do if you forget to enter the disarming code If you forget to e
6. Arming restarts from the beginning once all doors are closed Smart AutoArming includes all these additional features E AuioArming enable disable If you prefer you may deactivate or reactivate the AutoArming feature See User selectable features on pages 19 21 E Visual acknowledgment Five seconds after you exit the vehicle and close all the doors the parking lights will flash twice to confirm that the AutoArming countdown is progressing Then 25 seconds later the system will AutoArm Wi User selectable entry delay If you temporarily lose the use of your remote controls you may turn on the 15 second entry delay feature This allows you to silently disarm the system by starting the engine within 15 seconds of opening the door See User selectable features on pages 19 21 W AutoArm amp Lock To ensure you can t accidentally lock your keys inside the car the system is factory set not to lock the doors upon AutoArming To change this setting see User selectable features on pages 19 21 W Instant AutoArming bypass Prevents AutoArming when fueling the vehicle and other times when you wish to temporarily bypass AutoArming To activate Instant AutoArming Bypass rapidly turn the ignition switch to ON then OFF You will hear a single siren chirp to confirm that the system will not AutoArm The system reverts to its normal operating mode when you next start the engine 12 UltraSecure valet mode Within seconds thieves can disa
7. ILE THE SYSTEM IS ARMED TO REMOTELY OPEN THE TRUNK TO ACTIVATE OTHER OPTIONS REGARDLESS OF ALARM STATE What about channels 9 amp 10 Press button 3 channel 3 Your Concept 50 system will arm or disarm with all the indications noted on the previous page except for the chirp acknowledgments Button 2 channel 2 controls an interlock that allows you to separately command two different options with the same channel one when the system is armed and another when it is disarmed For instance if your Concept 50 was so wired pressing button 2 while the alarm is armed will either turn on the head lights for any duration you wish between 1 second and 2 5 minutes see the Headlight Timer feature in User selectable features on pages 19 21 OR will fully close all the power windows and sunroof on various Jaguar Mercedes Benz BMW and Volkswagen vehicles As noted above button 2 channel 2 can control yet another option when the system is disarmed The most obvious one is the remote trunk release If you have this option installed pressing button 2 while the alarm is disarmed will remotely open the trunk Button 4 channel 4 and channels 5 8 and 11 12 see How to use your keychain remote control on page 9 can activate other accessories such as the Clifford IntelliStart remote engine starter remote memory seat activation SmartWindows II remote window roll down and venting a Programmable Receiver t
8. The location is at the intersection of column 1 and row 2 Note the column and row numbers 3 With the ignition on enter you disarming code on the PlainView valet switch then hold the switch in its momentary position until you hear a chirp and see the LED turn on 4 Select feature column 1 by pressing the switch to its latched position then back to center After a brief pause you ll hear 1 chirp to indicate column 1 5 Press and release the momentary side twice You ll hear a total of two chirps to indicate that you selected the feature in row 2 of that column 6 After a brief pause you ll hear a single chirp to indicate that sound 2 is now off 7 Turn the ignition off you ll hear 3 chirps and you re done If you wish to turn siren sound 2 back on simply repeat steps 1 7 EXAMPLE 2 Turn off siren sound numbers 4 and 6 then turn on QuietChirps This time we will change the settings of three different features This time you ll hear the appropriate chirp confirmations but we won t make note of them in the instructions below 1 Enter program mode step 3 above 2 Latched center to select column 1 3 Four momentaries wait for the one chirp feature off confirmation then 6 momentaries to jump to row number 6 4 Four latched center presses to select column 4 5 One momentary wait for the two chirp feature on confirmation then turn the ignition off and you re done You just changed the
9. World Class Auto Security Owner s Manual All Concept Series systems are covered by one or more of the following Clifford Electronics patents 4 158 874 4 233 642 4 327 444 4 383 242 4 430 685 4 845 464 4 887 064 4 890 108 4 922 224 4 997 053 5 081 667 5 146 215 5 157 375 and other patents pending CLIFFORD WORLD CLASS AUTO SECURITY Table of Contents Standard Features ofthe Concept50 0 Welcome 2 au ca bad a dad ea wh eB a Built in vehicle recovery anti carjacking circuitry Definitions xus kt eu guod a k KO e ie ID d ded s PIQUE deseada A Rum E Mueve e che e ES Disamning Gode s as gun od a A RSE OG A FUP Se p qutt ed d PlainVIew SWIER x 2 um teat nd e ue So D s bem p e Sg Entetihig Q OI ia sce e e qme ARE LS dax eoe OI rs Pn Reo dud Entering decode s x er e ende ele n RR OE A D Ren Your secret disarming code ww 4 IMPORTANT What you MUST do to drive yourcar What you MUST do if you forget to enter the disarming code How to set your own secret disarming code 044 Enable disable anti carjacking 00 ooo omo es What to do in a carjacking situation iss Your 4 button 12 channel remote controls How to use your keychain remote control ToTransmit channel 1 2 SOPA fk so RURSUM ano To transmit channel 5 6 7 08 2s To transmit channel 9 10 110112 oos What each button channel do
10. able features section on pages 19 21 Remote QuickAccess For the greatest ease of use the Remote QuickAccess features permit you a quick and easy way of controlling with just the remote the most commonly used features You can control either of these features any time via your remote control Here s how W QuickAccess Valet Mode To enter valet mode remotely transmit channel 10 press the LevelShift button on the side of the remote control twice then press button 2 The parking lights will flash twice and the dashboard LED will stay on to indicate the system is in valet mode To exit valet mode remotely transmit channel 10 again and the system will exit of valet mode with one parking light flash and the LED will turn off NOTE If you enter valet mode via the remote control exit valet mode in the same manner If you use the PlainView switch to enter valet mode use the switch to exit valet mode W QuickAccess Long Term Chirp Silencing To silence the chirps transmit channel 9 press the LevelShift button on the side of the remote control twice then press button 1 The parking lights will flash twice to indicate that long term chirp silencing is on To restore the chirps transmit channel 9 again and the system will confirm restoration of the chirps with one flash of the parking lights 16 Smart prior intrusion attempt alert When you remotely disarm if you hear three chirps and see three parking light flashes instead of the us
11. at the LED indicator blinks twice pauses blinks twice etc this indicates level 2 E Jo transmit channel 9 10 11 or 12 Press the LevelShift button twice This shifts buttons 1 4 to level 3 channels 9 12 Then press the corresponding button within the next 7 seconds For instance to transmit channel 10 press the LevelShift button twice then press button 2 While you transmit you ll notice that the LED blinks three times pauses blinks three times etc this indicates level 3 Button 2 NOTE One second after you stop transmitting level 2 or level 3 channels 5 12 the remote control automatically returns to level 1 channels 1 4 9 What each button channel does Your Concept 50 remote controls come pre programmed so that certain channels command certain functions If you wish you can actually assign any channel except 11 and 12 to any function see pages 19 22 The following chart indicates what each remote control channel number does and how to transmit each channel number Factory settings of the 12 remote control channels Transmitting Pressthe How Press channel Causes the system to LevelShift many button number button times number 1 arm or disarm and lock or unlock the doors no 1 pop the trunk if the system is disarmed 2 AND no 2 turn on the headlights or close the windows if the system is armed 3 sil
12. ather than the siren itself This protects the circuitry from engine heat dirt and exposure to the elements in contrast the electronics of other alarm companies sirens are part of the siren itself and therefore far more susceptible to failure In addition to greatly enhancing long term reliability your Concept 50 also provides these additional features Personalized Siren Sounds Most alarm sirens have a single warble tone A few offer six tone sirens that either cannot be adjusted or require the physical destruction of certain circuit wires in order to change the sounds the change is permanent and cannot be changed again Your Concept 50 Medallion Siren circuitry is different As shipped from the factory the siren sounds six different alarm sound patterns However you may turn any of the six different alarm sound patterns on or off to create a different combination of sound patterns In all there are 64 different combinations you may select You may set your own Personalized Siren Sounds so if you hear a siren at a distance you will know for sure whether it is your car or someone else s See User selectable features on pages 19 21 QuiefChirps You can control the volume of the normal arm disarm chirps As shipped from the factory your system issues full volume chirp acknowledgments If you prefer you may reduce the chirp volume to a level that is clearly audible yet less obtrusive See the User selectable features sect
13. atile memory records the identity of the last eight activated or malfunctioning triggers and or sensors which allows your installer to instantly track down malfunctions and save you substantial servicing costs To identify the triggers and or sensors held in the system s non volatile memory simply perform the following procedure 1 With the ignition OFF flick the PlainView valet switch to its latched side 2 Press button I to arm the system then again to disarm 3 The LED will blink 1 6 times to indicate the most recently activated trigger or sensor pause then blink 1 6 times to indicate the next most recently activated trigger or sensor and so on for the last 8 activations beginning with the most recent 4 Write down the number of blinks between pauses and refer to the chart below Number of LED blinks per cycle Trigger sensor that was activated or malfunctioned 1 blink Magnetic Resonance Sensor 2 blinks Glass tampering sensor 3 blinks Door trigger 4 blinks Trunk trigger 5 blinks Hood trigger 6 blinks Proximity Sensor or other optional sensor Headlight reminder If you turn the ignition off and open the driver s door to exit the car without having turned off the headlights you will be reminded to turn them off with a distinctive warning tone If your vehicle already has a similar warning feature you may turn off your Concept 50 s Headlight Reminder See the User select
14. ble all other alarm brands by hot wiring the ignition and flicking an easy to find hidden valet switch Concept 50 has safeguards that absolutely ensure that a thief or carjacker cannot enable the valet mode as a way of turning off your system How To enter valet mode the driver must first enter the secret disarming code Whenever the system is put in valet mode all of the security and anti carjacking features are switched off At various times you will need to switch the system off For instance when having your car serviced washed or parked by a valet Remember When your car will be driven by someone else such as a mechanic who will not know your disarming code you must place Concept 50 in valet mode otherwise your car will be immobilized NOTE If you temporarily lose the use of your remote controls you can disarm the system by enabling valet mode To enable valet mode 1 Turn the ignition switch to its ON position or start the engine 2 Enter your secret disarming code on the PlainView switch then return the switch to its center position 3 You now have 3 seconds to flip the switch to the latched position valet mode Once you have enabled valet mode the system s LED will glow continually for on going visual confirmation of valet mode m Keyless entry in valet mode Even if valet mode is enabled you can still remotely control the convenience features For instance simply press button 1 channel 1 as if
15. ce again any channel you wish from 1 12 You will hear a two chirp confirmation You may now use this combination to turn off the 20 second anti carjacking countdown NOTE 11 Transmit the channel of your choice on the dedicated anti carjacking remote control You will hear two chirps to indicate that that remote control button will now turn off the 20 second anti carjacking countdown Be sure to carry this remote on your person since a carjacker will undoubtedly take your usual remote control and purse NOTE 12 Immediately flip the switch to its latched position then enter the new code that you wish to use Make sure to return the switch to its center position when complete then wait 3 seconds you will hear two chirps when the system has accepted the new code Turn the ignition off VERY IMPORTANT You must immediately test your new secret disarming valet code Turn the ignition on enter your new code then flip the switch to its latched position The LED will illuminate If it does not the new code you programmed and the one you just entered do not match The system has reverted to the previous code NOTE 13 The timer starts as soon as you enable this feature 6 latches 1 momentary When the duration you wish has been reached press button 1 on the remote control You will hear two chirps to confirm the new duration EXAMPLE 1 Turn off siren sound number 2 1 Look for the siren s sound number 2 location on the Matrix 2
16. ch time you press the momentary side to help you count a VERY IMPORTANT Tf there is a NOTE number listed in the selected feature of the matrix perform the actions listed for that note Once you have completed the NOTE instructions skip step 6 below and go to step 7 6 After a one second pause you will hear either one chirp to indicate that the feature you selected is now turned off or two chirps to indicate that the feature is now on on the siren duration feature one chirp 30 seconds two 60 seconds 7 You have now completed the programming of the desired featured You may select another feature or you may exit program mode a To program another feature in that same column you must repeat step 5 within the next 3 seconds if longer than 3 seconds you will hear three chirps to indicate that you are now in the Feature Select position b To select a different feature column go to step 4 c To exit program mode turn the ignition off you ll hear 3 chirps and the LED will turn off to indicate exit of program mode If driving just wait for 30 seconds and the system will automatically exit programming mode by itself indicated by 3 chirps and extinguishing of the LED The above may sound complicated but it really isn t There is just a lot of explanation involved with each step Briefly here is all you do Choose the feature you want to change enter program mode select the feature s column and row then turn off t
17. d lights to call attention and caution drivers behind your vehicle that it is about to stop It then sounds the Medallion Siren and waits for the carjacker to slow for a turn or traffic at which point it shuts down the engine and dynamically prevents it from being restarted If the carjacker tries to use the PlainView switch to enter code combinations at random the system will lock out for two minutes after three incorrect tries Even if he stumbles onto the correct code the carjacker is still locked out Unable to restart the vehicle and with the siren wailing and brake lights flashing the carjacker has no choice but to speedily abandon the vehicle You simply walk a block or two to your car enter your secret code and the system releases control of the vehicle to you Your 4 button 12 channel remote controls The 4 button 12 channel remote control is an ultra sophisticated miniature radio transmitter powered by a tiny 12 volt battery The range is up to 100 feet Obstructions electrical interference weather conditions or a weak battery will reduce the range Your 4 button 12 channel remote control is the key to your Concept 50 It incorporates Clifford s proprietary Anti Code Grabbing ACG technology with Random Code Generation for the ultimate in protection against code grabbing devices see page 12 You will use the remote to arm and disarm the system lock and unlock the doors activate the system s panic feature adjust sensor
18. ely No repeated arming and disarming and no siren wailing Concept 50 lets you set and test sensitivity without activating the alarm Y Remote Headlight Activation Capability Remotely turn on your vehicle s headlights to illuminate your way to and from your car Y Remote Window and Sunroof Closure Capability Fully close all the power windows and sunroof with a press of a button on your remote control W QuietChirps Select soft or full volume arm disarm chirp confirmations Y Dual Mode Chirp Silencing Long term chirp silencing or remote controlled chirp muting W Smart Trunk Release Capability Electronic interlock ensures that the trunk can be remotely opened only when the alarm is disarmed W Remote Door Locking Unlocking Lock unlock the car doors with your remote control m AutoLock Automatically locks the doors when the engine is started m AutoUnLock The doors automatically unlock when the ignition switch is turned off m Deluxe Remote Keyless Entry in Valet Mode Allows for remote door locking unlocking with visual parking light confirmations and interior light illumination even while the system is in valet mode W Remote Courtesy Lighting Automatically turns on your vehicle s interior light s when you remotely disarm the lights stay on for 30 seconds or until you start the engine whichever occurs first Ww Headlight Reminder Warns you if you forget to turn off t
19. ently arm or disarm no 3 4 activate optional accessory function 1 no 4 5 activate optional accessory function 2 yes once 1 6 activate optional accessory function 3 yes once 2 7 activate optional accessory function 4 yes once 3 8 activate optional accessory function 5 yes once 4 9 turn long term chirp muting on or off see QuickAccess on page 16 yes twice 1 10 enter or exit valet mode see QuickAccess on page 16 yes twice 2 11 activate optional accessory function 6 yes twice 3 12 activate optional accessory function 7 yes twice 4 May require additional wiring TO ARM Press button 1 channel 1 once You will hear two chirps and the THE SYSTEM parking lights will flash twice The dashboard LED will flash repeatedly and the car doors will automatically lock TO DISARM Press button 1 channel 1 again One chirp and one flash of the THE SYSTEM parking lights will confirm disarming In addition the car doors will automatically unlock and the interior lights will turn on and stay on for 30 seconds or until you start the engine whichever Occurs first TO ACTIVATE Press button 1 for 3 seconds The lights will flash repeatedly and THE PANIC the Medallion Siren will blare for 30 or 60 seconds FEATURE ooo oo user selectable or until you press button I again to turn it off 10 TO SILENTLY ARM OR DISARM THE SYSTEM TO REMOTELY TURN ON THE HEADLIGHTS OR REMOTELY CLOSE THE WINDOWS WH
20. es 1 0 How to interpret the chirps and parking light flashes APIS OE ou os suo Arator de ara Bs tat deett VU dut C eed es Anti CodeGrabbing ACG with Random Code Encryption Smart AutoArming M rousse a a eR Rene SRG AutoArming enable disable sns Visual acknowledgment n AUTOA LOCK o pos xs ux exo XX RR Instant AutoArming bypass i onn Entry Delays x sod ROW Rub Uie eu Ea S AD UlfraSecure valet mode 2 sn Io enable valetmode eire id ds iS aa Keyless entry in valet mode i s Io exit valet mode 5 3 5 su SUA Pd dI dd Table of Contents cont Dual sensor protection 13 Remote controlled sensor testing and adjustment 14 FACT False Alarm Control and Test 15 Smart Autfofesting ann 15 Specific malfunction identification es 15 Automatic malfunction bypass oes 15 Multiple event TotalRecall V 5 16 Headlight reminder nn 16 Remote QuickAccess o ooo o 16 QuickAccess Valet Mode 0 o 1 16 QuickAccess Long Term Chirp Silencing lis 16 Smart prior intrusion attempt alert sss 17 omartPowerUpTM I ora Bikes CR aram RO OE a 17 AutoLock AutoUnLocK x avs eR CR ed e Rea 17 Tamper proof ignition immobilization iss 17 How to interpret the LED
21. fo on page 9 10 amp 23 NOTE 4 output upon panic info on page 17 pulsed latched timed Sound 5 on off info on page 18 Add new remote to channel 5 accessory 2 info on page 9 10 amp 23 Headlight Reminder on off info on page 16 Smart AutoArming on off info on page 12 Siren duration 30 60 sec info on page 18 Channel 5 output pulsed latched timed NOTE 5 Erase all channels info on page 9 10 amp 23 NOTE 6 FACT on off info on page 15 Sound 6 on off info on page 18 Row th momentary Seta new secret AutoArm amp Lock on off disarming valet code QuickAccess valet mode on off info on page 12 info on pages 7 8 amp 13 info on page 16 NOTE 12 Gray cells indicate features that require programming by trained Clifford installers DO NOT change any of these setting WARNING If you have remote window and sunroof closure DO NOT CHANGE THIS SETTING it requires installer only adjustment Changing the duration may cause damage NOTE 1 Transmit channel 1 or other channel of your choosing of the new remote control You will hear two chirps to indicate that the code has been accepted and recorded NOTE 2 Transmit channel 2 or other channel of your choosing of the new remote control You will hear two chirps to indicate that the code has been accepted and recorded NOTE 3 Transmit channel 3 or other channel of your choosing of the new remote control You wi
22. hat lets you command your electric garage door gate opener s etc Channels 9 and 10 control the Remote QuickAccess features remote valet mode entry exit and remote long term chirp silencing restoration See Remote QuickAccess on page 16 How to interpret the chirps and parking light flashes When you use the remote control the system responds with chirps unless the chirp muting feature is turned on and parking light flashes These chirp flash acknowledgments mean Chirps and flashes Meaning 1 Your Concept system is disarmed 2 Your Concept system is armed 2 and then 4 Armed but there is a door open if there was a 5 sec delay or one of the Sensors is malfunctioning if there was a 10 sec delay see Smart AutoTesting 3 Disarmed and there was an intrusion attempt see Smart Prior Intrusion Attempt 4 Armed and there is a trigger malfunction see Smart AutoTesting 5 20 seconds to engine shutdown enter your disarming code IMMEDIATELY 11 AntiScan TM Thieves can disarm some other brands of car alarms with a scanner that rapidly transmits one remote control code after another Clifford s AntiScan will detect any scanner and block the codes it generates Anti CodeGrabbing ACG with Random Code Encryption Protects you and your automobile from the most effective and onerous car stealing device ever used by car thieves a code grabber Code grabbers are far more effective and
23. he ignition That s it Try the examples on page 22 to see just how easy it really is 19 Matrix of user selectable features Feature Select Column 1 Column 2 Column 3 Column 4 Column 5 Column Istlatched 2nd latched 3rd latched 4th latched 5th latched th latched Add new remote to Test adjust primary normal TIC E Row 1 Sound 1 on off channel 1 arm disarm zone of vibration sensor QuietChirps on off Anti carjacking on off didis iid a Ist momentary info on page 18 info on page 9 10 amp 23 info on pages 13 14 info on page 18 info on page 7 8 NOTE 13 NOTE 1 NOTE 7 Add new remote to Test adjust secondary high Long term Remote control button channel Row 2 Sound 2 on off channel 2 trunk timer zone of vibration sensor SER AGE sequence for anti carjacking rre 2nd momentary info on page 18 info on page 9 10 8 23 info on pages 13 14 ds M info on page 8 RELIGION NOTE2 NOTE 8 PH NOTE 10 abd CEN Test adjust glass Add a dedicated Row 3 Sound 3 on off arm disarm tampering sensor 15 second entry delay on off anti carjacking remote control Factory delayed 3rd momentary info on page 18 info on pages 13 14 info on page 12 info on page 8 courtesy lights on off info on page 9 10 amp 23 NOTE 9 NOTE 11 NOTE 3 Add new remote to Row 4 Sound 4 on off channel 4 accessory 1 Pulsed constant ground AutoLock UnLock on off Set idle RPM Channel 4 output 4th momentary Row 5 5th momentary info on page 18 in
24. he headlights after wW Patented Smart Autolesting Automatically tests all system sensors and triggers and identifies any malfunction On various models of BMW Mercedes Benz Jaguar and Volkswagen 4 Standard Features of the Concept 50 cont Patented Malfunction AutoBypass Automatically bypasses any trigger or sensor malfunction then arms all other points for the utmost possible protection Eight Event TotalRecall Stores the identities of the last eight triggers and or sensor activated This provides an invaluable informational and diagnostic means Remotely Activated Valet Mode Lets you engage or disengage valet mode via your remote control Remotely Activated Long Term Chirp Silencing You can also turn long term chirp muting on and off from up to 100 feet away Smart AutoArming Automatically passively arms itself if you forget May qualify you for a substantial discount on your vehicle insurance ask your insurance company m AutoArming Enable Disable Allows you to enable or disable AutoArming any time m Visual Acknowledgment Visually confirms initiation of the 30 second AutoArming countdown with two flashes of the parking lights m User Selectable AutoArm amp Lock Allows you to select whether the doors will lock when the system AutoArms m Instant AutoArming Bypass Lets you temporarily turn off AutoArming with just a turn of the ignition key Paten
25. ion on pages 19 21 Long term chirp silencing Whenever you wish you may silence your Concept 50 s arm disarm chirps until you decide to restore them The parking light flashes will continue to provide visual confirmation of remote controlled arming and disarming See User selectable features on pages 19 21 also see the Remote QuickAccess features on page 16 Remote controlled chirp muting Remote controlled chirp muting capabilities are especially valuable when parking late at night in a quiet residential area To arm or disarm silently simply press button 3 channel 3 on your remote control instead of the usual button 1 channel 1 Siren duration When the system detects an intrusion attempt the alarm is set to sound for 30 seconds However if you prefer you may change it to 60 seconds See the User selectable features section on pages 19 21 18 User selectable features Your Concept 50 allows you to set many of its features to your own personal preferences Although the system s programming capabilities are very extensive we have made the programming procedures very simple to make a change you just flick the PlainView switch a few times Once you ve changed a few settings you ll find that programming Concept 50 is so easy you can even do it while driving The system comes with all of its features pre programmed as noted by the bold type in the Matrix of user selectable features on the following page To change an
26. ll hear two chirps to indicate that the code has been accepted and recorded NOTE 4 Transmit channel 4 or other channel of your choosing of the new remote control You will hear two chirps to indicate that the code has been accepted and recorded NOTE 5 Transmit channel 5 or other channel of your choosing of the new remote control You will hear two chirps to indicate that the code has been accepted and recorded NOTE 6 When you hear the two chirps all remote control codes will have been erased from system memory You must now add the new and or existing remote controls to the system i e program channels 1 5 of each remote that will be used with your Concept 50 NOTE 7 Turn off the ignition exit the vehicle taking the keys with you and close the doors Firmly thump the window pillar with the side of your fist You should hear a chirp to confirm activation of the sensor s main zone Use remote control button 2 to increase sensitivity button 4 to decrease Repeat until the sensor is set to the sensitivity you wish then press remote control button 1 to end programming mode m NOTE 8 Use the same procedure as NOTE 7 but strike the window pillar lightly NOTE 9 Use the same procedure as NOTE 7 but firmly tap a coin such as a quarter against the window to test sensitivity NOTE 10 Transmit the first channel of your choice any channel from 1 12 You will hear a one chirp confirmation Transmit the second channel of your choi
27. locks them when you turn off the ignition If you prefer you may turn off the AutoLock AutoUnLock feature See the User selectable features section on pages 19 21 Tamper proof ignition immobilization While armed your Concept 50 system assures that your vehicle is completely immobilized by automatically locking out the ignition and or fuel systems That means that a thief won t be able to start your vehicle s engine even if he had a duplicate of your car key What s more even if he were to find the system control unit and tear it out of your vehicle he still won t be able to start your car s engine That s Clifford security you can count on 17 How to interpret the LED status indicator The LED on your car s dashboard or console will inform you of the system status LED Condition Meaning Off System is disarmed and in normal operating mode i e valet mode is off On Valet mode is on the vehicle can be driven or serviced without having to disarm Flashing ignition off System is armed and protecting your vehicle Flashing ignition on Anti carjacking feature was activated 20 second countdown to engine shutdown Enter your disarming code IMMEDIATELY Pause between flashes Either a malfunction see page 15 or an intrusion was attempted see page 17 High output Medallion Siren All the electronics for the system s siren are built into your Concept 50 s main control unit r
28. ne time b To test adjust the secondary high sensing zone of the Magnetic Resonance Sensor tap and release the momentary side of the switch two times c To test adjust the Glass Tampering Sensor tap and release the momentary side of the switch three times Turn the ignition off exit the vehicle and close the doors To test the current sensitivity setting a Magnetic Resonance Sensor Thump the window pillar with the side of your fist For the primary zone thump somewhat firmly but not nearly so hard as to dent the window pillar For the secondary high sensitivity zone thump rather lightly If the sensor registered the thump you will hear a single siren chirp b Glass Tampering Sensor Firmly tap on the window with a coin the larger the better If the sensor registered the tap you will hear a single chirp To increase sensitivity press button 2 on your remote control To decrease it press button 4 To confirm the change of setting each time you increase sensitivity the siren will chirp in higher and higher pitched tones Conversely as you decrease sensitivity the chirps will have lower and lower pitched tones Release the button when you hear the chirp Press and release the appropriate button until the desired sensitivity is reached There are 16 sensitivity steps for each sensor zone If you reach the highest or lowest setting the system will confirm this with two chirps of the siren Press remote contr
29. ngratulations on the purchase of your Clifford Concept 50 remote controlled vehicle security convenience system Your Concept 50 is packed with protective features and lifestyle convenience benefits that other car alarm companies don t even have on their wish lists let alone their alarms Features like Anti CodeGrabbing that fights off the latest and most onerous threat from high tech thieves A thief equipped with a code grabber can record with total impunity the codes of your car alarm s remote control from up to several hundred feet away How The thief simply waits for you to arm or disarm your alarm with your remote control The thief s portable pocket sized code grabber will automatically pick and record the transmitted code off the air As soon as you walk away he simply plays it back instantly disarming your alarm and unlocking the doors It s like giving the thief your car keys Code grabbing will instantly defeat all other brands of remote controlled car alarms regardless of whether they are equipped with anti scanning or trillions of digital codes Concept 50 s built in BlackJax anti carjacking and vehicle recovery system enhances your personal safety and virtually assures that your vehicle can be promptly recovered intact Clifford s unique PlainView Coded Valet Switch ensures that no thief carjacker or joy rider can turn off your Concept 50 like they can with all other car alarm brands For total freedom from incorrec
30. nter the code Concept 50 will remind you to do so 20 seconds after you begin driving by chirping the siren 5 times and flashing the LED on the dashboard At this point you have another 20 seconds to enter your code When entered the LED will stop flashing If the proper code is not entered within 20 seconds after the 5 chirp signal the engine will shut down You may enter your disarming code even after the engine is shut down Once the proper disarming code is entered you will be able to resume driving How to set your own secret disarming code Since all Concept 50 systems have the same factory set disarming code 2 it is highly advisable that you set your own disarming code You may choose any 1 2 or 3 digit disarming code so long as it does not have any zeros You can also change your disarming code whenever and wherever you want See User selectable features on pages 19 21 Enable disable anti carjacking If you prefer you may enable or disable the anti carjacking feature see User selectable features on pages 19 21 or temporarily override it via valet mode see page 13 What to do in a carjacking situation In a carjacking situation the sooner you are out of the car the better Don t resist or take anything with you just get out and get away The instant the car door is opened Concept 50 takes charge First it lets the carjacker drive your vehicle a short distance ensuring your safety Then it flashes the brake hazar
31. ol button 1 when done to exit programming mode you ll hear a chirp and the LED inside the vehicle will turn off to indicate that the system has exited programming mode You may now either enter the vehicle to drive it or program another feature or press button 1 to arm the system 14 FACT False Alarm Control and Test With FACT you ll never experience repeated false alarms If your Medallion Siren goes off DO NOT remotely disarm the system while the siren sounds allow it to run for the full siren duration Before sounding the siren a second time the system automatically checks for another activated trigger to verify that an intrusion is in progress Should the siren sound again you will know for sure that someone is tampering with your vehicle To disable FACT see User selectable features on pages 19 21 Smart AutoTesting Each time you remotely arm your Concept 50 it will perform a series of tests on all triggers and sensors If the hood or trunk is open when you arm the system Concept 50 will immediately alert you of the problem by issuing 4 chirps and 4 parking light flashes instead of the usual 2 and 2 If a door is ajar you will receive the usual 2 chirps and flashes then 5 seconds later there will be 4 chirps and 4 flashes This door ajar warning will not work on vehicles that have factory delayed courtesy lights If one of the sensors is malfunctioning you will receive the usual 2 chirps and 2 flashes then 10
32. ontrol Allows you to command Concept Series systems on your other vehicle s with the same remote control W Patented Remote Control Code Learning and MultiRemote Recognition Add or delete with just a few flicks of a switch up to four Clifford Anti CodeGrabbing remote controls W Patent Pending UltraSecure Coded Valet Mode Ensures no thief or carjacker can turn off your Concept system like they can all other alarm brands W Built In Parking Light Flasher Visually confirms alarm status from a distance Standard Features of the Concept 50 cont W Dual Sensor Protection The Dual Zone Magnetic Resonance Sensor detects intrusion related vibrations and the Glass Tampering Sensor detects attempts to break any window W Remote Sensor Adjustment Incredibly easy and accurate sensor adjustment and testing Just use the remote control to adjust your sensor any time any place without tools and without even knowing where the sensor is mounted m 16 Step Incremental Sensitivity Adjustment For the utmost in fine tuning accuracy Gives you remote controlled access to 16 sensitivity levels for each of the two sensing zones of the Magnetic Resonance Sensor m Tonal Confirmations of Sensor Adjustments As you remotely increase sensitivity the confirming chirps rise in pitch Conversely as you lower each zone s sensitivity the confirmation chirps become lower and lower in pitch m Adjust and Test Unobtrusiv
33. ple and easy Definitions W Digit A digit is defined as any number from 1 to 9 inclusive E Disarming code A disarming code may be 1 to 3 digits A one digit code X any number between 1 9 A two digit code XY any number between 11 99 excluding numbers with zeros A three digit code XYZ any number between 111 999 excluding numbers with zeros Remember no code can have a zero W PlainView switch A rocker switch mounted on the dashboard or console The switch has three positions 1 Latched 2 Center 3 Spring loaded momentary When you press the latched side the switch remains in its pressed position When you press the momentary side the switch bounces back to the center position Each time you drive your car you must enter your secret disarming code via the PlainView switch m Entering a digit To enter a digit you tap press and release on the momentary side of the PlainView switch the number of times corresponding to the numeral of the digit to be entered followed by pressing to the latched side then returning the switch to its center position m Entering a code If your code has only one digit enter the code as described in Entering a digit then return the switch to its center position If your code has more than one digit just repeat the above for each digit of your code then return the switch to its center position Your secret disarming code Unless the system is in valet mode see page 13 within
34. sensors In fact an improperly adjusted sensor is by far the biggest cause of false alarms With other alarm brands this requires repeated trips back to the dealer Not so with Concept 50 You can adjust sensitivity without any tools and without even knowing where the sensor is mounted All you need is your car alarm s remote control If at any time you find the setting s of your system s sensors to be either too sensitive 1 e it tends to false alarm or not quite sensitive enough you may individually test and adjust the sensitivity settings yourself To adjust the Glass Tampering Sensor or either zone of the Dual Zone Magnetic Resonance Sensor just use the following procedure 1 2 MO Insert your car key and turn the ignition switch to its ON position but do not start the engine Enter your disarming code then press and hold the switch to its spring loaded momentary side for about 3 seconds until you hear a siren chirp You ll also notice that the system s LED is on to indicate that the system is in its programming mode Toggle the switch in and out of the latched position 3 times 1 e latched center latched center latched center You will hear a chirp for each latched center you perform To select either the sensor and or zone perform either a b or c of this section a To test adjust the primary normal sensing zone of the Magnetic Resonance Sensor tap and release the momentary side of the switch o
35. status indicator 18 High output Medallion Siren 0 0 18 Personalized Siren Sounds o 18 Quiefchirps TM a AA cd Gol a BT ee da eed un 18 Long term chirp silencing orn 18 One time remote controlled chiro muting 18 Sirer rgo s c ue eR a en tes a gh qd 18 User selectable features ooo ern 19 Matrix of user selectable features oss 20 21 EXAMPLE 1 Turn off sien sound number2 2s 23 EXAMPLE 2 Turn off siren sound numbers 4 and 6 then turn on QuietChirps 23 Adding new remote controls sn 23 How to erase the codes of lost or stolen remote controls 23 Standard Features of the Concept 5O W Limited Lifetime Warranty Your system control unit and remote controls are covered for as long as you own your car see warranty card for details Ww FACT False Alarm Control and Test Eliminates recurring false alarms W Built In BlackJax Anti Carjacking System You get all of these features for the ultimate in safe and effective vehicle recovery W Greatest Carjack Protection No buttons to push no transmitters to carry you do nothing except get out of the vehicle Your Concept 50 allows the criminal to arive a safe distance of a block or two then flashes the parking lights sounds the Medallion Siren and safely shuts down the engine m Safe amp Intelligent Engine Shutdown Concept 5O waits for
36. ted Smart Prior Intrusion Attempt Alert Specifically identifies the sensor or trigger activated by an attempted intrusion while you were away High Output Medallion Siren Designed exclusively by Clifford Electronics for greater performance and 10 times the reliability of other manufacturers sirens W Personalized Siren Sounds To distinctly identify your vehicle from a distance you may at any time select your choice of any of 64 different siren sound combinations m User Selectable 30 60 second siren duration W Patented Automatic Noise Abatement Limits alarm sounding to no more than 5 siren duration cycles to prevent battery drain and towing of the vehicle due to noise pollution Fault Proof Starter Interrupt Output Prevent an intruder from cranking the engine while the system High Luminescence LED Indicator Adds visual deterrence and provides visual confirmation of system status Full Time Remote Panic Feature Lets you remotely activate the siren and parking lights inside or outside the vehicle or even while driving Multiple Trigger Sensor Inputs For greater security and precise identification of the exact trigger or sensor tripped in a prior intrusion attempt Full Time User Friendly Programming Access You can alter feature settings to precisely suit your needs It s so easy you can even do it while driving Welcome to the world of high technology vehicle security and convenience o
37. the carjacker to slow for traffic or a turn then safely shuts down the engine without endangering the lives of others m immediate Vehicle Recovery Since the vehicle will be immobilized just a block or two away you can recover it yourself well before it reaches the chop shop m PlainView Coded Disarming Switch No hidden switch that carjackers can find in an instant The PlainView switch accepts only your code and you may change your code any time or place m Anti Tampering If the carjacker tries entering codes and or button sequences at random after three incorrect codes the system will lock itself out for two minutes and not respond to any code even if the criminal were to stumble onto the correct one m Sabotage Proof Even if the thief could find the system control unit and tear it out of the car the engine REMAINS IMMOBILIZED W Ignition Immobilization Your car s ignition and fuel system are electronically disconnected while your Concept 5O is armed Y A Pair of 4 Button 12 Channel Remote Controls For fingertip command of your Concept 50 system from up to 100 feet away W Antiscan Blocks electronic scanners from disarming your system W Proprietary Anti CodeGrabbing ACG with Random Code Encryption Since the remote control never transmits the same code twice the random code encryption makes the new remote control code grabbers used by thieves completely useless W Multiple Car C
38. tly adjusted sensors there s remote controlled adjustment of the system s Dual Zone Magnetic Resonance Sensor that allows you to set the desired sensitivity level any place or time with just a touch of a button on your remote control Plus there s remote controlled valet mode user programmable Medallion Siren with 64 distinctly different siren sound combinations to set your alarm apart from all others full time programming access even while you re driving to dozens of features and much much more Yet despite all the sophistication your Concept 50 is amazingly easy to use never more difficult than a few flicks of a switch or a press of a button on one of your miniature keychain remote controls 6 Built in vehicle recovery anti carjacking circuitry Concept 50 s built in BlackJax circuitry provides a safe and effective means of recovering your vehicle after a theft or carjacking IMPORTANT The factory setting for this feature is OFF Once you are familiar with the following we suggest you turn this feature ON see pages 20 22 When anti carjacking is on each time you begin driving you MUST enter your disarm ing code as noted below unless the system is in valet mode Your secret disarming code tells the system that the car is being driven by an authorized person Also if you open your car door at any point as would occur in a carjacking attempt you must again enter your secret code Entering your code is sim
39. ual one and one it means that a trigger or sensor was activated in your absence When you enter the vehicle and turn on the ignition or start the engine the LED will blink several times pause then repeat the blink cycle 4 more times Count the number of blinks in one cycle and refer to the chart below Number of LED blinks per cycle Trigger sensor that detected the intrusion attempt 1 blink Magnetic Resonance Sensor 2 blinks Glass tampering sensor 3 blinks Door trigger 4 blinks Trunk trigger 5 blinks Hood trigger 6 blinks Proximity Sensor or other optional sensor SmartPowerUp II If power to the system control unit is ever removed SmartPowerUp II ensures that the system will automatically restore itself to its previous status when power is restored So if a thief tampers with the vehicle battery in an attempt to steal your car the system will automatically re arm itself and immediately sound the siren However if your vehicle is to be serviced by a mechanic just put the system in valet mode If the mechanic needs to interrupt vehicle power your system will automatically return to its valet mode state when power is restored there will be no alarm activation and no need to provide your mechanic with your remote control and instructions on how to use it AutoLock AutoUnLock For your safety and that of your passengers the system automatically locks the doors when you begin driving and un
40. y of the settings use the steps noted below To restore the feature to its factory setting just repeat the procedure 1 Refer to the Matrix of user selectable features and make note of the column number and row number of the feature s you wish to program 2 Insert your ignition key and turn it to the ON position or start the engine skip this step if the engine is already running 3 Enter your disarming code then press and hold the PlainView switch to its spring loaded momentary side for about 3 seconds until you hear a siren chirp You ll also notice that the system LED turns on to indicate that the system is in its programming mode The system is now in the Feature Select position the top left cell of the matrix From this position you will first select the feature column from left to right then the feature row from top to bottom 4 Select the feature column To select the column you wish toggle the switch in and out of the latched position the same number of times as the column number of the selected feature NOTE each latched to center motion is counted as one After a one second pause you will hear the same number of chirps as the column number you have selected audibly confirming your selection 5 Select the feature row To select the feature s row immediately tap and release the momentary side of the switch the same number of times as the feature s row number You will hear a single chirp confirmation ea
41. you were disarming The doors will unlock as indicated by one flash of the parking lights and the interior lights will illuminate Press button 1 channel 1 again and the doors will lock indicated by two parking light flashes You can also use the remote control s other channels to activate options such as a remote trunk release or remote engine starting To exit valet mode 1 Turn the ignition switch to its ON position or start the engine you may also perform the following while driving 2 Flick the switch back to its center position The LED will turn off to confirm that the system is now in its normal operating mode NOTE You can even enable or exit valet mode with your remote control from outside the vehicle See the Remote QuickAccess section on page 16 Dual sensor protection Concept 50 system has two sensors a Glass Tampering Sensor that detects attempts to break any of the vehicle s windows and a Dual Zone Magnetic Resonance Sensor that detects intrusion related vibrations What s more the secondary high sensitivity zone of the Dual Zone Magnetic Resonance Sensor can detect someone forcefully leaning against your vehicle s fender and will warn the person off with an unmistakable warning tone instead of the full siren blast which is reserved for a genuine intrusion attempt 13 Remote controlled sensor testing and adjustment Because of ever changing conditions all alarms require periodic fine tuning of the
Download Pdf Manuals
Related Search