Home

Clarion CX609E Car Stereo System User Manual

1. Be sure to lower the volume before switching off the unit power or the ignition key The unit remembers its last volume setting Turning on off the power Note 1 Press the SRC button to turn on the power 2 Press and hold the SRC button 1 sec for to turn off the power Selecting a mode 1 Press the SRC button to change the operation mode Radio CD MP3 WMA AAC USB MTP iPod gt BLUETOOTH AUX Radio IPod MTP can connect to this unit via USB cable Adjusting the volume 1 Turning the ROTARY knob clockwise increases the volume turning it counterclockwise decreases the volume The volume level is from 0 minimum to 33 maximum Switching the display Press the DISP button to select the desired display 8 CX609E Sound Adjustment You can adjust a sound effect or tone quality to your preference To change sound setting 1 Press the JI button to switch to the sound adjustment selection display The factory default sound setting is BEAT EQ 2 Then press the I or PP button to select the sound adjustment mode Each time you press the k44 or gt gt I button the sound adjustment mode changes as following order BEAT EQ lt gt M B EX gt BALANCE gt FADER LPF gt S W VOL gt HPF In the case of display blinking ENT you can press the gt button to adjust the setting value 3 Press the
2. This function allows you to locate and play the first 10 seconds of the first track of all the folders on an MP3 WMA AAC disc 1 Press and hold the SCN button 1 sec for folder scan play Repeat play This function allows you to play the current track repeatedly 1 Press the RPT button to perform repeat play Folder repeat play This function allows you to play a track currently being played in the MP3 WMA AAC folder repeatedly 1 Press and hold the RPT button 1 sec for folder repeat play Random play This function allows you to play all tracks recorded on a disc in a random order 1 Press the RDM button to perform random play Folder random play This function allows you to play all the tracks of all the folders recorded on an MP3 WMA AAC disc in a random order 1 Press and hold the RDM button 1 sec for folder random play To cancel play 1 Press the operating button previously selected The various play mode is canceled and the various play off mode appears in the display for 2 seconds CX609E 1 7 Bluetooth Operations The Bluetooth allows you to utilize your car s built in audio system for wireless mobile phone or music handsfree communication Some Bluetooth mobile phones have the audio features and some portable audio players support Bluetooth feature This system can play audio data stored in a Bluetooth audio device The car stereo with Bluetooth insta
3. Bluetooth Ver 2 0 Profile HFP Hands Free Profile OPP Object Push Profile Phone Book A2DP Advanced Audio Distribution Profile AVRCP Audio Video Remote Control Profile Send Receive Sensitivity Class 2 Note General Output Power 25 W X 4 DIN 45324 B 14 4V Power Supply Voltage 14 4 V DC 10 8 to 15 6 V allowable negative ground Power Consumption Less than 15 A Speaker Impedance 4 Q 4 to 8 Q allowable Weight Main unit 1 59 kg Dimensions Main unit 178 W X 100 H X 155 D mm e Specifications and design are subject to change without notice for further improvement 10 O0THERS WMDRM 10 for devices e This product is protected by certain intellectual property rights of Microsoft Use or distribution of such technology outside of this product is prohibited without a license from Microsoft e Content owners use Windows Media digital rights management technology WMDRM to protect their intellectual property including copyrights This device uses WMDRM software to access WMDRM protected content If the WMDRM software fails to protect the content content owners may ask Microsoft to revoke the software s ability to use WMDRM to play or copy protected content Revocation does not affect 32 CX609E unprotected content When you download licenses for protected content you agree that Microsoft may include a revocation list with the licenses Content owners may require you to upgrade WMDRM to ac
4. USB Mass Storage Class standards Audio files playable on this unit are limited to MP3 WMA AAC files For details see the section MP3 WMA AAC page 15 e The Podcast files of iTunes Store that stored in the USB memory device can not be played Besides the data that edit through some softs such as the Tag edit soft may not be played To prevent the accidental loss of data always back up important data on your computer e This unit does not support connections to a computer In addition connections made through a USB hub device are also not supported e When a USB memory device is composed of two or more drives only one of the drives will be detected e USB memory devices with security functions cannot be played e The order in which tracks are recorded may differ depending on the USB memory device connected the actual playback order may not be the same as that indicated on your computer s display e If you continuously operate folder up down the play time keeps as 00 00 and the sound is not emitted About USB Digital Media Streaming This unit supports USB Digital Media Streaming USB Digital Media Streaming is a function used to play music files transmitted using Media Transfer Protocol MTP This function also supports the playback of WMDRM 10 files During USB Digital Media Streaming the unit displays the MTP mode indicator Use of USB Digital Media Streaming requires the purchase of
5. button to select TELPHONE or AUDIO then press the MI button For a no paired device after reset or at the same time when you select TELEPHONE please press the A or W button to select the phone book type For details see the chaperter PHONE BOOK TYPE page 20 3 3 After select the TELEPHONE press the A or W button to select MEMORY 1 to MEMORY 5 then press and hold the NY button 1 sec to memory 4 1 Press the A or V button to select SEARCH or WAIT 5 1 Press and hold the II button 1 sec When the SEARCHING appears in the display you can press the Il button to stop search then the list search appear SEARCH mode User can search the Bluetooth mobile phone or audio device WAIT mode User can search this uint via the mobile phone or audio device 6 1 After the search press the A or W button to select the desired Bluetooth mobile phone 7 1 Press and hold the button 1 sec to pair SELECT This is a setting for user to select one of the paired mobile phones or audio 2 1 Select SELECT 3 1 Press the II button then the paired mobile phones appears in the display 4 1 Press the A or V button to choose one of the 5 mobile phones 5 1 Press and hold the button 1 sec to connect Connected device will be able to use all the functionalities provided DELETE This
6. modes press and hold 1 sec for folder random play iPod mode 44 gt gt I buttons e Press to move the tracks up and down Press and hold 1 sec for fast forward fast reverse gt I button e Switches between playback and pause AF button e Press to perform repeat play PTY button e Press to perform random play Press and hold 1 sec for all random play Turn over the remote control unit and slide the cover in the direction indicated by the arrow in the illustration Insert the battery CR2025 into the insertion guides with the printed side facing upwards Press the battery in the direction indicated by the arrow so that it slides into the compartment Replace the cover and slide in until it clicks into place Notes Misuse may result in rupture of the battery producing leakage of fluid and resulting in personal injury or damage to surrounding materials Always follow these safety precautions e Use only the designated battery e When replacing the battery insert properly with polarities oriented correctly e Do not subject battery to heat or dispose of in fire or water Do not attempt to disassemble the battery e Dispose of used batteries properly Insertion guide CX609E 7 5 OPERATIONS Note Be sure to read this chapter referring to the front diagrams of chapter 3 CONTROLS on page 5 Basic Operations A CAUTION
7. please do not set the BASS MID TREBLE in the maximum level Otherwise the speakers may be damaged 3 2 Press the II button 3 3 Press the I or gt button to select as following order BASS lt G gt gt BASS lt F gt gt BASS lt Q gt MID lt G gt MID lt F gt gt MID lt Q gt TREBLE lt G gt TREBLE lt F gt lt gt TREBLE lt Q gt The factory default setting is BASS lt G gt 3 4 Press the A or V button to select the setting BASS lt G gt The factory default setting is 0 Adjustment range 7 to 7 BASS lt F gt The factory default setting is 50 Adjustment range 50 100 200 BASS lt Q gt The factory default setting is 1 Adjustment range 0 7 1 1 4 2 MID lt G gt The factory default setting is 0 Adjustment range 7 to 7 MID lt F gt The factory default setting is 500 Adjustment range 500 1K 2K MID lt Q gt The factory default setting is 1 Adjustment range 0 7 1 1 4 2 TREBLE lt G gt The factory default setting is 0 Adjustment range 7 to 7 TREBLE lt F gt The factory default setting is 10K Adjustment range 5K 10K 15K TREBLE lt Q gt The factory default setting is 1 Adjustment range 0 7 1 1 4 2 3 5 Press the gt button to return to the ENT previous mode Setting the MAGNA BASS EXTEND The MAGNA BASS E
8. 2 Press the I lt or gt button to select AF 3 Press the A or V button to select ON or OFF ON AF in the display lights and AF function turns on OFF AF in the display goes off and AF function turns off 4 Press the DISP button to return to the previous mode If the reception of the current broadcast station deteriorates PISEARCH appears in the display and the radio searches for the same programme on another frequency REG Regional programme function When the REG function is ON the optimum regional station can be received When this function is OFF if the regional station area switches as you drive a regional station for that region is received The factory default setting is OFF Notes e This function is disabled when a national station such as BBC R2 is being received e The REG function ON OFF setting is valid when the AF function is ON 1 Press and hold the DISP button 1 sec to switch to the Radio Data System adjustment selection display 2 Press the I lt or gt button to select REG 1 2 CX609E 3 Press the A or V button to select ON or OFF ON REG in the display lights and REG function turns on OFF REG in the display goes off and REG function turns off 4 Press the DISP button to return to the previous mode Manually tuning a regional station in the same networ
9. Loading a CD 1 Insert a CD into the center of the CD SLOT with the labeled side facing up The CD plays automatically after loading Notes e Never insert foreign objects into the CD SLOT e If the CD is not inserted easily there may be another CD in the mechanism or the unit may require service co e Discs not bearing the Oise or is iG mark and This a CD ROMs cannot be played by unit e Some CDs recorded in CD R CD RW mode may not be usable Pausing play 1 Press the II button to pause play PAUSE appears in the display 2 To resume CD play press the button again 1 6 CX609E Displaying CD titles This unit can display title data for CD text MP3 WMA AAC disc and user titles input with this unit 1 Each time you press the DISP button to change the title display CD TEXT disc User Track Disc Artist User MP3 WMA AAC disc Track Folder Title Album Artist Track Notes e If the CD playing is not a CD text CD or no user title has been input NO TITLE appears in the display e If MP3 WMA AAC disc is not input TAG NO TITLE appears in the display e For MP3 supports ID3 Tags V2 3 2 2 1 1 1 0 e Tag displays give priority to V2 3 2 2 e In the case of album Tags for WMA the information written into the extension header is displayed e Only ASCII characters can be displayed in Tags Selecting a track Track up 1 Press the gt P1 button to
10. MEMORY 1 2 3 4 250 250 0 0 piece piece piece piece 200 100 100 50 piece piece piece piece 100 100 100 100 piece piece piece piece MIC GAIN MIC gain can be set by each paired mobile phone device Each registered device has unique MIC gain setting 2 1 Select MIC GAIN 3 1 Press the A or W button to change the MIC gain setting The factory default setting is 3 Adjustment range 1 to 5 RING VOL This option is used to change the ringing volume by each paired mobile phone device 2 1 Select RING VOL 3 1 Press the A or W button to change the ringing volume The factory default setting is 5 Adjustment range 1 to 10 TONE SEL The system can ring if the mobile phone cannot ring when the Bluetooth connection has been established 2 1 Press TONE SEL 3 1 Press the A or V button to select INTERNAL or AUTO The unit setting is AUTO INTERNAL Adjust tone in the car bluetooth system Bluetooth Operations AUTO Automatic adjustment is enabled in the paired mobile phone NOISE This option is used to set noise volume in the car bluetooth system 2 1 Press NOISE 3 1 Press the A or V button to select LOW or HIGH The factory default setting is LOW AUTO ANS This is a setting to determine whether any incoming call will be automatically or manually answered The factory default sett
11. a supported portable audio player For information regarding supported portable audio players consult your nearest Clarion dealer or visit Clarion s website A CAUTION e Insert and remove a USB memory MTP device only when the device is not being accessed Connecting or disconnecting the device at the following times may result in the loss of data If the USB memory MTP device is removed or power is disconnected during writing to the device When the device is subjected to static electricity or electric noise e Do not leave a USB memory MTP device unattended in an automobile Exposure to direct sunlight or high temperatures may cause deformation or other malfunction of the USB memory MTP device CX609E 25 USB MTP Operations Do not turn on vehicle ignition when the MTP device is connected since it may result in loss or damage to data on the MTP device Connect the MTP device to the USB cable after vehicle ignition is turned on Connecting a USB memory MTP device 1 Connect the USB memory MTP device to the USB cable Playback will begin from the first file recorded on the device If the device is not recognized press the SRC button to switch the source to the device Always insert the device fully into the connector Incomplete connections may cause the device not to be recognized Depending on the number of tracks recorded some amount of time may be required until all tracks
12. and MP3 WMA AAC type tracks use this command to select which type of track to play Default setting is MULTI SESS CD e When only one type of track either music CD or MP3 WMA AAC is recorded on a disc selecting either type will allow playback of the disc e When playing CCCD copy control CDs set to CD type 1 Press and hold the BND button for 1 second or longer Each time the button is held pressed in this way the playback type alternates between CD type and MP3 WMA AAC type e MULTI SESS CD When playing music CD only e MULTI SESS MP3 When playing music MP3 WMA AAC only 2 When setting is completed remove the disc and reinsert it CX609E 1 5 CDIMP3 WMA AAC Operations 3 When setting is completed remove the disc and reinsert it Backup Eject function Just pressing the 4 button ejects the disc even if the power to the unit was not turned on 1 Press the EJECT button Remove the disc after it is ejected Notes e If you force a CD into before auto reloading this can damage the CD e Ifa CD 12 cm is left in the ejected position for 15 seconds the CD is automatically reloaded Auto reload Listening to a disc already loaded in the unit Press the SRC button to select the CD MP3 WMA AAC mode When the unit enters the CD MP3 WMA AAC mode play starts automatically If there is no disc loaded the indication NO DISC appears in the title display
13. default setting is OFF 2 1 Select INT SW 3 1 Press the A or W button to select the setting Each time you press the A or V button the setting changes in the following order OFF lt gt ON lt gt MUTE OFF This unit continues normal operation even when the cellular phone is used ON You can listen to your telephone calls from the speakers connected to this unit x When listening to your calls on your car speakers you can adjust the volume by turning the ROTARY knob MUTE The sound from this unit is muted during telephone calls Note e If connecting a hands free kit please ensure the setting is ON to receive the telephone audio through the system the sound output from the AUX Selecting Rear or Subwoofer The factory default setting is BEAR 2 1 Select REAR S W 3 1 Press the A or V button to select REAR or S WOOFER Performing a system check This function allows you to perform a system check from the adjust mode when required 2 1 Select SYSTEM CHECK 3 1 Press and hold the MI button 1 sec SYSTEM CHECK appears in the display then the unit returns to the previous operation mode Entering titles Titles up to 10 characters long can be stored in memory and displayed for CD There 50 titles that can be entered 1 Press the SRC button to select the mode you want to enter a title CD 2 Select and
14. in the display TP stations are automatically sought DX SEEK Press the I or gt I button to automatically seek a station When the gt button is pressed the station is sought in the direction of higher frequencies if the I button is pressed the station is sought in the direction of lower frequencies LOCAL SEEK If the 4 or gt button is pressed and held in position for 1 second or longer local seek tuning will be enabled Broadcast stations with good reception sensitivity are selected Manual tuning 2 ways available Quick tuning and step tuning Quick tuning Press and hold the 4 or gt I button 1 sec to tune a station Step tuning Press the I or bb button to manually tune a station If no operation is performed for more than 7 seconds manual tuning is cancelled and the display returns to the previous mode Recalling a preset station A total of 24 preset positions 6 FM1 6 FM2 6 FM3 6 AM exists to store individual radio stations in memory Press the corresponding DIRECT button or the A or W button to recall the stored radio frequency automatically Manual memory 1 Select the desired station with seek tuning or manual tuning 2 Press and hold one of the DIRECT buttons 2 sec to store the current station into preset memory Auto store Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially If 6 recei
15. move ahead to the beginning of the next track 2 Each time you press the BI button the track advances ahead to the beginning of the next track Track down 1 Press the 4 button to move back to the beginning of the current track 2 Press the I button twice to move back to the beginning of the previous track Fast forward Fast reverse Fast forward 1 Press and hold the PP button 1 sec Fast reverse 1 Press and hold the 4 button 1 sec For MP3 WMA AAC discs it takes some time until the start of searching and between tracks In addition the playing time may have a margin of error CD MP3 WMAIAAC Operations Folder Select This function allows you to select a folder containing MP3 WMA AAC files and start playing from the first track in the folder 1 Press the V or A button Press the A button to move the next folder Press the W button to move the previous folder 2 To select a track press the 4 or gt gt I button Top function The top function resets the CD player to the first track of the disc Press the BND button to play the first track track No 1 on the disc In case of MP3 WMA AAC the first track of a folder being played will be returned Other various play functions Scan play This function allows you to locate and play the first 10 seconds of all the tracks recorded ona disc 1 Press the SCN button to perform scan play Folder scan play
16. repeatedly 1 Press the RPT button Random play Play all albums within a selected category in random order Corresponds to Shuffle Albums command on iPod 1 Press the RDM button CX609E 2 7 iPod Operations All random play Play all tracks within a selected category in random order Corresponds to Shuffle Songs command on iPod 1 Press and hold the RDM button 1 sec To cancel play 1 Press the same play button once again Notes e When the repeat play mode is canceled after play all tracks within a selected category playback will begin from the first track in the selected category e When playing the last track within a selected category in Random mode if ACC is switched off then on again playback will begin from a different track e Though the default setting of an iPod is All Repeat the indication on the mode status is not displayed e When performing operations using simple control mode do not set the repeat off on the iPod Selecting category from the iPod menu 1 Press and hold the BND button to select the iPod menu mode The iPod menu categories will be displayed Notes e Repeat and Random mode operations are not supported when in the iPod menu mode e In iPod menu mode if you press the t amp lt gt or A W button fast playback may not be performed 2 Press the A or V button to switch between categories The iPod menu cat
17. select a music file once again Setting iPod simple mode Use this function if you wish to operate through your iPod connected to this unit via the USB cable The factory default setting is OFF 1 Press and hold the DISP button 1 sec Press k44 or gt P to select S CTRL 2 3 Press the PII button 4 Press the A or W button to select ON or OFF ON Operations can be made through your iPod OFF Operations cannot be made through your iPod 5 Press and hold the I button 1 sec to store the setting and return to the previous mode Notes e When performing iPod operations using simple control mode make the operations slowly If repetitive operations are performed too quickly unforseen errors may occur e When performing iPod operations using simple control mode please do not operate the iPod and the unit at the same time otherwise there may be unexpeted event happened e Some iPod models do not support this function Consult your nearest Clarion dealer or website to contirm which models do not support this function Other various play functions in Play mode Notes e These functions are not supported when in the iPod menu mode e The Random function set on the iPod remains the same after attachment detachment of the iPod e The Repeat function on the iPod will be changed when you connect disconnect the iPod to the unit e Repeat play Play back one track
18. set during TA Alarm or PTY interrupt The factory default setting is 15 During a TA Alarm or PTY interrupt turn the ROTARY knob to set the volume to the desired level 0 to 33 x When the TA Alarm or PTY interrupt ends the volume returns to the level it had before the interrupt 1 4 CX609E CD MP3 WMAI AAC Operations This unit can play back MP3 WMA AAC files Notes e If you play a file with DRM Digital Rights Management for WMA remaining ON no audio is output The WMA indicator blinks e Windows Media and the Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries To disable DRM Digital Rights Management 1 When using Windows Media Player 9 10 11 click on TOOL OPTIONS MUSIC RECORD tab then under Recording settings unclick the Check box for RECORD PROTECTED MUSIC Then reconstruct files Personally constructed WMA files are used at your own responsibility Precautions when creating MP3 WMAI AAC file Usable sampling rates and bit rates 1 MP3 Sampling rate 8 kHz 48 kHz Bit rate 8 kbps 320 kbps VBR 2 WMA Bit rate 8 kbps 320 kbps 3 AAC Sampling rate 8 kHz 48 kHz Bit rate 8 kbps 320 kbps VBR File extensions 1 Always add a file extension MP3 WMA or M4A to MP3 WMA or AAC file by using single byte letters If you add a file extension other than specified or forget to add
19. the file extension the file cannot be played 2 Files without MP3 WMA AAC data will not play The files will be played soundlessly if you attempt to play files without MP3 WMA AAC data When VBR files are played the play time display may differ the play location When MP3 WMA AAC files are played a little no sound part is caused between tunes Logical format File system 1 When writing MP3 WMA AAC file on a CD R disc or CD RW disc please select ISO9660 level 1 2 or JOLIET or Romeo or APPLE ISO as the writing software format Normal play may not be possible if the disc is recorded on another format 2 The folder name and file name can be displayed as the title during MP3 WMA AAC play but the title must be within 64 single byte alphabetical letters and numerals including an extension 3 Do not affix a name to a file inside a folder having the same name Folder structure 1 Adisc with a folder having more than 8 hierarchical levels will be impossible Number of files or folders 1 Up to 255 files can be recognized per folder Up to 510 files can be played 2 Tracks are played in the order that they were recorded onto a disc Tracks might not always be played in the order displayed on the PC 3 Some noise may occur depending on the type of encoder software used while recording Set the type of file to be played multi session function When a single disc holds both normal CD type tracks
20. A or W button to adjust the selected audio mode 4 After completing settings press the Js button to return to the previous mode Setting the BEAT EQ This unit is provided with 4 types of sound tone effects stored in memory Select the one you prefer The factory default setting is OFF 2 1 Select BEAT EQ 3 1 Each time you press the A or V button the tone effect changes in the following order CUSTOM gt EXCITE IMPACT gt B BOOST OFF CUSTOM user custom EXCITE bass and treble emphasized mid emphasized IMPACT bass and treble emphasized B BOOST bass emphasized OFF no sound effect Basic Operations When CUSTOM is set 3 1 Press the button ENT 3 2 Press the I or gt button to select the BASS MID TREBLE mode to adjust 3 3 If you want to set the flat press the I button to return to the CUSTOM mode then press and hold the button 1 sec bass mid treble characteristics become flat When EXCITE IMPACT B BOOST is set 3 2 Press the PI button 3 3 Press the A or V button to adjust the setting in the range of 3 to 3 The factory default setting is 0 3 4 Press the PH button to return to the previous mode Adjusting the BASS MID TREBLE This adjustment can be performed only when the BEAT EQ is set to CUSTOM Note e While connected with the external aplifers
21. Clarion Owner s manual Mode d emploi Bedienungsanleitung Istruzioni per l uso Gebruiksaanwijzing Manual de instrucciones Bruksanvisning Manual de instru es CX609E 2 DIN Bluetooth CD USB MP3 WMA AAC RECEIVER LECTEUR CD USB MP3 WMA AAC Bluetooth 2 DIN Bluetooth CD USB MP3 WMA AAC RECEIVER 2 DIN SINTOLETTORE CD USB MP3 WMA AAC Bluetooth a 2 DIN 2 DIN Bluetooth CD USB MP3 WMA AAC ONTVANGER RECEPTOR CD USB MP3 WMA AAC Bluetooth 2 DIN 2 DIN Bluetooth CD USB MP3 WMA AAC RECEIVER RECEPTOR Bluetooth duplo DIN CD USB MP3 WMA AAC CAUTIONS This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT To use this model properly read this Owner s Manual carefully and keep this manual for your future reference In case of any trouble with this player please contact your nearest AUTHORIZED service station To prevent direct exposure to the laser beam do not try to open the enclosure USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE ADVARSEL Denne m rking er anbragt udvendigt p apparatet og indikerer at apparatet arbejder med laserstr ler af klasse 1 hvilket betyder at der anvendes laserstr ler af svageste klasse og at man ikke p apparatets yderside kan blive udsat for utilladelig kraftig str ling APPARATET B R KUN BNES AF FAGFOLK MED S RLIGT K
22. Control Unit BUttons i 6 Inserting the Batteryca cena iaia Ralieriiiai 7 5 OPERATIONS ilaele ia 8 Basic OperationS cri ani a 8 Radio Operations ssa Radio Data System Operations sc 12 CD MP3 WMA AAC Operations 15 Bluetooth Operations 18 Operations Common to Each Mode si 22 6 ACCESSORIES Gio iL lalla lalui 25 USB MTP Operationsi a aeaii ara iieiaei kasaa a aen iaia 25 IPod Op ration Spisar rpa a r aeaa a aa E ena AN AE eden 27 7 TROUBLESHOOTING LEE iii 30 8 ERROR DISPLAYS Gili lla lui elle eil 31 9 SPECIFICATIONS isni la I aaa 32 10 OTHERS lalla le lille abile alain 32 mes RDS Biod SR BBEW CX609E 3 1 FEATURES Built in Bluetooth handsfree HFP and audio streaming A2DP amp AVRCP e BBE MP for compressed audio improvement e 728 Variable colour display amp illuminated key 2 PRECAUTIONS This unit is applicable for on road 4 wheel vehicle purpose only Use for tractor fork truck bulldozer off road vehicle 2 or 3 wheel motor bicycle marine boat or other special purpose vehicle is not appropriate INFORMATION FOR USERS CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY Handling Compact Discs e Compared to ordinary music CDs CD R and CD RW discs are both easily affected by high temperature and h
23. EL NO PHONE BOOK 3 1 Press the PI button 4 1 Press the A or W button to select 1 DEL or ALL DEL 5 1 When you select 1 DEL press the gt button then press the A or V button to select one of the desired phone No 6 1 Press the PI button then the DELETE appears in the display 7 1 Press the gt H button 1 sec to delete Note e If you want to transfer or hand this unit please perform DELETE ADD PHONE BOOK and DEL NO PHONE BOOK function to delete all of your personal information HISTORY DELETE ALL This option is used to delete all of the call records 2 1 Select HISTORY DELETE ALL 3 1 Press the II button then the CONFIRM appears in the display 4 1 Press the II button 1 sec then the DELETING appears in the display detele all of the call records successfully 2 0 CX609E PHONE BOOK TYPE The unit provide 3 types of phone book which are stored in memory 2 1 Select PHONE BOOK TYPE 3 1 Press the I button 3 2 Press the A or V button to select 4 2 or 3 then press the T button to store in memory Notes e If you change the phone book type all of the paired mobile phones s book data will be deleted e The piece number of the phone book s record can be stored in the different memory of the phone book type are as follow MEMORY MEMORY MEMORY
24. ENDSKAB TIL APPARATER MED LASERSTRALER Indvendigt i apparatet er anbragt den her gengivne advarselsmeekning som advarer imod at foretage s danne indgreb i apparatet at man kan komme til at udsa tte sig for laserstraling 2 CX609E Apparaten inneh ller laserkomponenten som avger laserstralning 6verstigande gransen for laserklass 1 Suojakoteloa si saa avata Laite sisaltaa laserdiodin joka l hett n kym t nt silmille vaarallista lasersateilya 12V GROUND emcTYPE_1040xx LW 153 279kHz MW 531 1602kHz 226 C FM UKW 87 5 108MHz CLASS 1 LASER PRODUCT This product includes technology owned by Microsoft Corporation and cannot be used or distributed Without a license from MSLGP Bluetooth ID 276 SERIAL No CF Clarion Co Ltd PEL MADE IN Thank you for purchasing this Clarion product Please read this owner s manual in its entirety before operating this equipment After reading this manual be sure to keep it in a handy place e g glove compartment Check the contents of the enclosed warranty card and keep it carefully with this manual Contents VFEATURES cecilia il 4 2 PREGAUTIONS LIL LL LL LL i ii 4 CONTROLS uiliilenlil elit 5 Names of the Buttons and Their Main Functions ens enn ns enn ennen rr erne renen 5 4 REMOTE CONTROL lt ci RI LR 6 Functions of Remote
25. Press the A or W button to select the desired letter to search 6 Press the DISP button to perform search During search press the DISP button to cancel search ask Selecting category using preset memory 1 Press and hold the BND button 1 sec to select the iPod menu mode The category can be set as follows in the DIRECT 1 6 buttons 1 PLAYLISTS 2 ARTISTS 3 ALBUMS 4 SONGS 5 GENRES 6 COMPOSERS 2 Press the desired DIRECT 1 6 button to select the category Subfolders may be displayed depending on the category In this case use the A or W buttons to switch between subfolders then use the PP button to select the desired subfolder 3 When the track name display is showing press the PP button iPod Operations Playback will begin from the first track in the selected category and the iPod menu mode will be canceled Use the A or V buttons to select a track within a category iPod menu list back In the iPod menu operation mode If press the BND button it will return to the previous subfolder list mode If press and hold the BND button 1 sec it will return to the category list mode About title display This unit supports the display of title information transmitted from a connected iPod e Character code information is UTF 8 displayable characters include English alphanumerics some symbols and some umlaut characters e Unsupporte
26. TP and TA lit in the display press the TA button The TA in the display goes off and the TA standby mode is cancelled Radio Data System Operations If TP is not lit pressing the TA button searches for a TP station Searching for a TP station When TP is not lit if you press the TA button TA in the display lights and the unit automatically receives a TP station Auto store function for TP stations You can automatically store up to 6 TP stations into preset memory If the number of TP can be received less than 6 broadcast stations already stored in memory and left without being overwritten As TA lit in the display press and hold the X1 button 2 sec The TP stations with the good reception sensitivity are stored into preset memory x Even if you select FM1 or FM2 a TP station is stored into memory for FM3 PTY Programme Type This function enables you to listen to a broadcast of the selected programme type even if the unit is on a function mode other than radio Some countries do not yet have PTY broadcast In the TA standby mode a TP station has priority over a PTY broadcast station The factory default setting is OFF 1 Press and hold the DISP button 1 sec to switch to the Radio Data System adjustment selection display 2 Press the I or gt button to select PTY 3 Press the A or V button to select ON o
27. XTEND does not adjust the low frequencies like the normal sound adjustment function but emphasizes the deep bass frequencies to provide you with a dynamic sound The factory default setting is OFF off 2 1 Select M B EX 3 1 Press A or W button to select ON or OFF Adjusting the balance 2 1 Select BALANCE 3 1 Press the A or V button to adjust the balance of the right and left speakers The factory default setting is CENTER center Adjustment range RIGHT12 to LEFT12 right 12 to left 12 e Adjusting the fader 2 1 Select FADER 3 1 Press the A or V button to adjust the balance of the rear and front speakers The factory default setting is CENTER center Adjustment range FRONT12 to REAR 12 front 12 to rear 12 Adjusting the subwoofer You can set the low pass filter of subwoofer This adjustment can be performed only when the REAR S W is set to S WOOFER page 24 2 1 Select LPF 3 1 Press the A or V button to select as following order THROUGH lt gt 60 lt gt 90 gt 120 The factory default setting is THROUGH Adjusting the subwoofer output volume You can adjust the volume output from the unit s subwoofer output terminal This adjustment can be performed only when the REAR S W is set to S WOOFER page 24 CX609E 9 Basic Operations 2 1 Selec
28. Y broadcast can be received the unit returns to the PTY select mode PTY preset memory 1 Press and hold the DISP button 1 sec to switch to the Radio Data System adjustment selection display Press the k44 or gt button to select PTY SELECT Press the PI button Press the A or W button to select the desired PTY The 29 types of PTY below can be selected If you press and hold any one of the DIRECT buttons 2 sec the selected PTY is stored into that preset channel memory CX609E 1 3 Radio Data System Operations Emergency broadcast If an emergency broadcast is received all the function mode operations are stopped ALARM appears in the display and the emergency broadcast can be heard Cancelling an emergency broadcast If you press the TA button emergency broadcast reception is cancelled Switching the PTY display language You can select one of 4 languages English German Swedish or French for the PTY displayed in the display The factory default setting is ENGLISH 1 Press and hold the DISP button 1 sec to switch to the adjustment selection display 2 Press the I or gt button to select LANGUAGE 3 Press the A or W button to select the desired language 4 Press the DISP button to return to the previous mode Volume setting of TA emergency broadcast Alarm and PTY The volume for TA Alarm and PTY interrupts can be
29. are read into the unit The order in which tracks are recorded may differ depending on the device connected the actual playback order may not be the same as that indicated on your computer s display To listen to tracks on a connected USB memory MTP device 1 Press the SRC button to switch the source When USB memory MTP device is selected playback except DRM files will begin from the location at which playback was previously stopped When a USB memory MTP device is connected the USB MTP mode will be displayed When a USB memory MTP device is disconnected and then reconnected playback will begin from the beginning of the USB memory MTP device When MTP mode is selected AAC files on the MTP device cannot be played 2 6 CX609E To stop play 1 Press the SRC button and switch the function to a source other than the USB memory MTP A CAUTION Do not remove the USB memory MTP device when the USB MTP mode is selected since it may result in loss or damage to data on the USB memory MTP device Always backup and save important data on your computer 2 Remove the USB memory MTP device from the USB cable iPod Operations This section describes operations when connected to an Apple iPod via the USB cable Notes e See the iPod Owner s Manual for details regarding operation conditions e The unit will not operate or may operate improperly with unsupported versions e For a lis
30. cess their content If you decline an upgrade you will not be able to access content that requires the upgrade Clarion E TEL 49 6105 977 0 FAX 49 6105 977 399 _ _ Clarion JNE DI D M 28 agosto 1995 no548 lo Fabbricante Mandatario nell UE Clarion Europa GmbH Hessenring 19 21 64546 Morfelden Walldorf Dichiaro che il prodotto Autoradio con CD CX609E conforme alle disposizioni contenute nel suddetto decreto relativamente alla prevenzione e l eleminazione dei disturbi radioelettrici provocati dai ricevitori di radiodiffusione sonora e televisiva lo Fabbricante Mandatario nell UE Data 22 Gennaio 2009 Clarion Europa GmbH Hessenring 19 21 64546 Morfelden Walldorf FirmaAkihiko Nadabe PBL No 09IRJA001C IDCFMTFWLH004 CX609E 2 75 n_ Clarion E VIG TEL 49 6105 977 0 FAX 49 6105 977 399 CE DECLARATION of CONFORMITY Document No 09DC CE01 address declare under our sole responsibility that the product CAR RADIO with CD PLAYER name type or models possibly sources and numbers of items to which this declaration relates is in conformity with the following standard s or other normative document s And following the provisions of _ Directive according to paragraph 3 2 9 of Annex I meets the limits defined in paragraph 6 6 6 6 6 8 and 6 9 of Annex I Place and date of issue name and signature or equivalent marking of authorized person Clar
31. cleaning alcohol No sound heard The speaker protection circuit is operating 1 Turn down sound volume Function can also be restored by turning the power off and on again Speaker volume is reduced automatically when the speaker protection circuit operates 2 If the sound is muted again consult our service department CD MP3 WMA AAC 30 No sound heard MP3 WMA AAC files are absent in a disc Write MP3 WMA AAC files onto the disc properly Files are not recognized as an MP3 WMA AAC file Use MP3 WMA AAC files encoded properly File system is not correct Use ISO9660 level 1 2 or JOLIET or Romeo or APPLE ISO file system Sound skips or is noisy Compact disc is dirty Clean the compact disc with a soft cloth Compact disc is heavily scratched or warped Replace with a compact disc with no scratches Sound is cut or skipped Noise is generated or noise is mixed with sound MP3 WMA AAC files are not encoded properly Use MP3 WMA AAC files encoded properly Sound is bad directly after power is turned on Water droplets may form on the internal lens when the car is parked in a humid place Let dry for about 1 hour with the power on Wrong filename CX609E File system is not correct Use ISO9660 level 1 2 or JOLIET or Romeo or APPLE ISO file system Problem Cause Measure me o a a t D No sound heard T
32. d characters will be replaced by asterisks CX609E 29 7 TROUBLESHOOTING Problem Cause Measure Power does not turn on No sound is produced Fuse is blown Replace with a fuse of the same amperage If the fuse blows again consult your store of purchase Incorrect wiring Consult your store of purchase No sound output when operating the unit with amplifiers or power antenna attached Power antenna lead is shorted to ground or excessive current is required for remote on the amplifiers or power antenna 1 Turn the unit off 2 Remove all wires attached to the power antenna lead Check each wire for a possible short to ground using an ohm meter Turn the unit back on Reconnect each amplifier remote wire to the power antenna lead one by one If the amplifiers turn off before all wires are attached use an external relay to provide remote on voltage excessive current required Nothing happens when buttons are pressed Display is not accurate The microprocessor has malfunctioned due to noise etc Turn off the power then press the OPEN button and remove the DCP Press the reset button for about 2 seconds with a thin rod If the RESET button is pressed when a disc is loaded Please eject the disc and load it once again before attempting to play it DCP or main unit connectors are dirty Wipe the dirt off with a soft cloth moistened with
33. egories alternate in the following order PLAYLISTS gt ARTISTS gt ALBUMS gt SONGS gt GENRES gt COMPOSERS Note The iPod menu mode can be canceled by performing one of the following operations e Press the BND button e When the category select screen is displayed press the P button 3 Press the PP button to select the category 4 When the track name display is showing press the Pl button Playback will begin from the first track in the selected category and the iPod menu mode will be canceled 2 8 CX609E Subfolders may be displayed depending on the category In this case use the A and W buttons to switch between subfolders then use the DPI button to select the desired subfolder x When the track name display is showing pressing the I button will return to the currently playing folder name display 5 Use the A and W buttons to select a track within a category iPod menu alphabet search This function searches the subfolders for desired alphabetical letters 1 Press the BND button to select the iPod menu mode 2 Press the A or V button to switch between categories 3 Press the 44 button Subfolders may be displayed depending on the category In this case you can use the A or W button to switch between subfolders and use the PP button to enter the next subfolder layer Press and hold the DISP button 1 sec
34. ent Press to alternate among main display title broadcast an emergency broadcast and a display and CT clock time display PTY broadcast during a TA ALARM or PTY i _ interrupt e Radio Radio Data System mode A V buttons BND button e Increases and decreases volume e Switches reception band MUTE button 4 gt gt buttons Turns mute function on and off e Moves preset channels up and down TA button PS AS button e TA on and off Press to perform preset scan Press to cancel a traffic announcement Press and hold the button 2 sec for auto broadcast during a TA interrupt store 6 CX609E Functions of Remote Control Unit Buttons AF button e AF function on and off Press and hold 1 sec for REG function on and off PTY button e PTY mode on and off CDIMP3 WMA AAC and USB MTP modes BND button Press to play the first track 44 gt PI buttons Press to move the tracks up and down Press and hold 1 sec for fast forward fast reverse gt I button e Switches between playback and pause PS AS button Press to perform scan play e When in MP3 WMA AAC and USB MTP modes press and hold 1 sec for folder scan play Inserting the Battery AF button Press to perform repeat play e When in MP3 WMA AAC and USB MTP modes press and hold 1 sec for folder repeat play PTY button Press to perform random play e When in MP3 WMA AAC and USB MTP
35. evices connected to this unit are difficult to hear even after adjusting the volume The factory default setting is MID 1 Press and hold the DISP button 1 sec 2 Select AUX SENS 3 Press the A or W button to select HIGH MID or LOW Note e When AUX mode is selected AUX IN sensitivity can be set 6 ACCESSORIES USB MTP Operations USB memory MTP device operation Note e The following operations are the same as for CD mode x Pause Track selection Fast forward reverse Except DRM file Top function List search function Scan play Repeat play x Random play Folder selection See CD MP3 WMAIAAC Operations page 15 17 for details About USB memory USB is an acronym for Universal Serial Bus and refers to an external bus standard supporting data transfer rates of 12 Mbps This unit is compatible with USB 1 1 2 0 with maximum data transfer rates of 12 Mbps e USB memory devices that can be played by connecting to the unit s USB cable are limited to those recognized as USB mass storage class devices operation is not guaranteed with all USB memory devices Devices compatible with USB Mass Storage Class can be used merely by connecting to the host device without need for special drivers or application software e Consult the manufacturer of your USB memory device for information regarding whether it is supported by
36. f current settings When the setting is selected after 1 second the current state will be displayed For example after 1 second Setting the button illumination 2 1 Select COLOR 3 1 Press the A or V button to select the color type e Setting COLOR SCAN mode As selecting COLOR SCAN the color automatically changes The factory default setting is COLOR SCAN After 3 seconds the color changes to the other 22 CX609E e Setting USER mode The factory default setting is RED 8 red GREEN 8 green BLUE 8 blue As selecting USER COLOR 1 2 3 press the pu button to enter the setting 1 Press the 4 or dI to select RED GREEN or BLUE 2 Press the A or V button to select from 0 to 8 3 Press and hold the gt u button for 2 seconds or longer to store the color in memory and cancel the setting mode e Setting the anti theft function CATS CATS is the acronym of Clarion Anti Theft System When you set a PIN code called as Personal Code a theft is prevented by disabling the operation of the unit at the theft e Setting your Personal Code 2 1 Select CODE 3 1 Press the gt I button ENT The set personal code screen appears 4 1 Press the DIRECT buttons 1 6 to enter your desired 4 digit Personal Code 5 1 Press and hold the button 2 sec The entered Personal Code wi
37. he CD deck and is not ejected This is a failure of CD deck s mechanism and consult your store of purchase ERROR 3 A CD cannot be played due to scratches etc Replace with a non scratched non warped disc ERROR 6 A CD is loaded upside down inside the CD deck and does not play Eject the disc then reload it properly USB MTP iPod ERROR 2 The files are not proper MP3 WMA AAC format Use only properly encoded MP3 WMA AAC files ERROR 3 USB MTP mode The MP3 WMA AAC files are improperly encoded Use only properly encoded MP3 WMA AAC files CUR ERR Overcurrent detection Disconnect the devices and reconnect If the devices are still not recognized try replacing with a different devices HUB ERR Do not support the HUB devices Do not use the HUB devices If an error display other than the ones described above appears press the reset button If the problem persists turn off the power and consult your store of purchase 31 CX609E 9 SPECIFICATIONS Radio section Tuning System PLL synthesizer tuner Receiving Frequencies FM 87 5 to 108 MHz 0 05 MHz steps MW 531 to 1602 kHz 9 kHz steps LW 153 to 279 kHz 3 kHz steps CD player section System Compact disc digital audio system Frequency Response 20 Hz to 20 kHz 1 dB Signal to Noise Ratio 100 dB 1 kHz Dynamic Range 80 dB 1 kHz Distortion 0 03 Bluetooth Specification
38. he device contains no MP3 WMA AAC files Record MP3 WMA AAC files properly to the device The files are not proper MP3 WMA AAC format Use only properly encoded MP3 WMA AAC files Connectors are loose Disconnect the device and reconnect securely Some USB portable music players may consume current that exceeds the USB rating In this case the unit s overcurrent protection circuit operates to stop the Music playback Check operation of portable music player Sound is interrupted or has noise The MP3 WMA AAC files are improperly encoded Use only properly encoded MP3 WMA AAC files The device isn t recognized The device is damaged Connectors are loose Disconnect the device and reconnect If the device is still not recognized try replacing with a different device According to the state of operation on the device the communication fault is caused Disconnect the device and reconnect Can t insert the device The device has been inserted improperly Try reversing the connection direction of the device usually the brand name surface should be facing left The connector is broken Replace with a new device 8 ERROR DISPLAYS If an error occurs one of the following displays is displayed Take the measures described below to eliminate the problem Error Display Cause Measure CD MP3 WMA AAC ERROR 2 A CD is caught inside t
39. ing is OFF 2 1 Select AUTO ANS 3 1 Press the A or V button to select ON or OFF ON Any incoming call is automatically answered in 5 seconds OFF User needs to manually answer the call e AUTO CON This function allows the Bluetooth to be connected automatically with previously connected device Connection can be established at any source mode The factory default setting is OFF 2 1 Select AUTO CON 3 1 Press the A or V button to select ON or OFF ON Automatic connection is enabled OFF Automatic connection is disabled PASS KEY This PASS KEY is used during pairing mode A maximum of 10 digits can be changed through the car stereo The factory default PASS KEY is 1234 2 1 Select PASS KEY 3 1 Press the PII button 4 1 Press the k44 or gt button to remove the cursor 5 1 Press the A or V button to select the desired digits 6 1 Press and hold the RI button 2 sec to store in memory If press the BND button the pass key returns to the factory default setting ADDRESS This will hold the unique Bluetooth address The address is 12 figures 2 1 Select ADDRESS The Bluetooth address 6 figures appears in the display 3 1 Press the A or V button to display Bluetooth Name This will display the name of the Bluetooth 2 1 Select BT NAME The Bluetooth name appears in the display Bluetooth F
40. ion Co Ltd All Rights Reserved Copyright 2008 Clarion Co Ltd Printed in China Imprim en Chine Gedruckt in China Stampato in Cina PE 3154E 2008 12 Gedrukt in China Impreso en China Tryckt i Kina Impresso na China 280 8711 00
41. irmware version This will display the firmware version of the Bluetooth 2 1 Select BT FW The Bluetooth firmware version appears in the display CX609E 2 1 Operations Common to Each Mode To change adjustment setting 1 Press and hold the DISP button 1 sec to switch to the adjustment selection display Press the 4 or gt button to select the item name CONTRAST gt SETTINGS lt gt COLOR lt gt CODE lt gt SCRN SVR lt gt MESSAGE INPUT lt SCROLL lt gt DIMMER lt gt BLINKLED lt gt A CANCEL INT SW gt REAR S W lt gt SYSTEM CHECK Press the A or W button to select the desired setting value In the case of display blinking ENT you can press the button to adjust the setting value After completing settings press the DISP button to return to the previous mode Setting the contrast You can adjust the display contrast to match the angle of installation of the unit The factory default setting is 10 Adjustment level 1 to 16 2 1 Select CONTRAST 3 1 Press the A or V button to adjust the contrast Displaying the settings The number of indicator of this unit decreases you can see the state of current settings at any operation mode 2 1 Select SETTINGS 3 1 Press the A or V button to display the state o
42. is a setting for user to delete one of the paired device from the list 2 1 Select DELETE 3 1 Press the I button then the paired mobile phones appears in the display 4 1 Press the A or V button to choose one of the 5 mobile phones and a audio device 5 1 Press and hold the button to delete the paired device Notes e Deleted paired device will not automatically rearrange in the paired device list e After deleting the device the phone book and the call history records will be deleted too CX609E 1 9 Bluetooth Operations DISCONNECT This option is used to disconnect the currently connected device 2 1 Select DISCONNECT 3 1 Press and hold the MI button 1 sec to disconnect Press and hold the JI button 2 sec to disconnect ADD PHONE BOOK This option is used to add one of the phone No 2 1 Select ADD PHONE BOOK 3 1 Press the button 1 sec then the ENT RECEIVING appears in the display At the same time the phone No from the paired phone book list is sent out then there is a prompt on the mobile phone if it is successful Some mobile phones cannot transfer the phone book to this unit because of the less word and the language type In this time please edit your phone book in other language and transfer it once again DEL NO PHONE BOOK This option is used to delete one of or all phone No of the added phone book 2 1 Select D
43. k 1 This function is valid when the AF function is ON and the REG function is OFF Note e This function can be used when a regional broadcast of the same network is received 2 Press any one of the DIRECT buttons to call out the regional station 3 If the reception condition of the called out station is bad press the DIRECT button of the same number The unit receives a local station on the same network TA Traffic Announcement In the TA standby mode when a traffic announcement broadcast starts the traffic announcement broadcast is received as top priority regardless of the function mode so you can listen to it Traffic programme TP automatic tuning is also possible This function can only be used when TP is lit in the display When TP is lit this means that the Radio Data System broadcast station being received has traffic announcement programmes Setting the TA standby mode If you press the TA button when only TP is lit in the display TP and TA light in the display and the unit is set into the TA standby mode until a traffic announcement is broadcast When a traffic announcement broadcast starts TRA INFO appears in the display If you press the TA button while a traffic announcement broadcast is being received the traffic announcement broadcast reception is cancelled and the unit goes into the TA standby mode Cancelling the TA standby mode As
44. ll be set and it will return to the previous screen Note e Write down your Personal Code in case you forget it Erasing the Personal Code 2 1 Select CODE 3 1 Press the II button The ERASE PERSONAL CODE screen appears 4 1 Enter the Personal Code currently 5 1 Press and hold the pM button 2 sec or longer Enter a Personal Code mode is cancelled When the ENTER PERSONAL CODE screen appears The ENTER PERSONAL CODE screen will be displayed when turning the ACC power on after performing the following operations e The car battery was replaced e The backup power was cut off e The RESET button was pressed Operations Common to Each Mode Note e If you have lost your Personal Code please contact Clarion customer service 1 Enter your Personal Code currently set 2 When the correct Personal Code is entered the unit will restart from the initial startup screen Notes e When you enter a wrong Personal Code the message LOCK is displayed and the Personal Code entry is prohibited for a while This prohibited time is changed according to the number of times of wrong code entry as follows e 1 to 6 times 15 seconds e 7 times or more 15 minutes Turning the screen saver function on or off This unit is provided with the screen saver function which allows you to show various kinds of patterns and characters in the operation status indication area of the display in a rando
45. lled will be able to retrieve phonebook contacts received call dialed call missed call incoming calls outgoing call redial call and listen to music Notes e Do not leave the microphone of Bluetooth handsfree in the places with wind passing such as air outlet of the air conditioner etc This may cause a malfunction In addition if leave it in the places subjected to direct sun high temperature can cause distortion discoloration which may result in a malfunction e This system will not operate or may operate improperly with some Bluetooth audio players e For detailed information on the playable Bluetooth audio players see our home page www clarion com e When a audio device is paired the following operations are the same as for CD mode Pause Track selection Fast forward Fast reverse e The titles and the play time can not appear in the display See CD MP3 WMAIAAC Operations page 15 17 for details Basic Operations Select Bluetooth 1 Press the SRC button to switch the source 2 You can press and hold the JI button to disconnect the currently connected device Switch the display Press the DISP button to select the display in the following order BT TEL gt BT AUDIO The connected device name will appear in the display 1 8 CX609E Making a call There are 4 ways to make outgoing call Direct Number Call Outgoing call can be made by entering telephone n
46. m order You can turn on or off this function If the button operation is performed with the screen saver function on the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display The factory default setting is ON 2 1 Select SCRN SVR 3 1 Press the A or V button to select the setting Each time you press the A or V button the setting changes in the following order MESSAGE lt ON OFF Entering message information Message up to 30 characters long can be stored in memory and displayed as a type of screen saver setting The factory default setting is WELCOME TO CLARION 2 1 Select MESSAGE INPUT 3 1 Press the II button 3 2 Press and hold the BND button 1 sec to clear the old message 3 3 Press the I or gt button to move the cursor 3 4 Press the BND button to select a character type Each time you press the BND button the character type changes in the following order Capital letters Numbers Symbols Umlaut Capital letters 3 5 Press the A or V button to select the desired character 3 6 Repeat step 3 3 to 3 5 to enter up to 30 characters for message 3 7 Press and hold the button 2 sec to store the message in memory Press and hold the BND button 1 sec to cancel the input message Then press and hold the II button 2
47. on to select the contact name s phone number 4 Press the II button to call the mobile phone No Bluetooth Operations Redial a call You can call a redial phone No 1 Press the BND button to select REDIAL 2 Press and hold the I button 1 sec to call the redial phone No Press the Js button to end the call To change Bluetooth adjustment setting 1 Press and hold the DISP button 1 sec to switch to the Bluetooth adjustment selection display Press the 4 or gt I button to select the item name PAIRING gt SELECT DELETE DISCONNECT gt ADD PHONE BOOK gt DEL NO PHONE BOOK lt gt HISTORY DELETE ALL lt gt PHONE BOOK TYPE MIC GAIN lt RING VOL TONE SEL NOISE AUTO ANS gt AUTO CON gt PASS KEY ADDRESS BT NAME BT FW Press the A or W button to select the desired setting value x In the case of display blinking ENT you can press the button to adjust the setting value After completing settings press the DISP button to return to the previous mode PAIRING This option is used to perform Bluetooth pairing with the mobile phone and audio Up to a maximum of 5 mobile phones and a audio device can be paired 2 1 Select PAIRING 3 1 Press the II button 3 2 Press the A or V
48. play a CD for which you want to enter the title 3 Press and hold the DISP button 1 sec 24 CX609E 5 Press the k44 or gt button to select TITLE INPUT 5 Press the I button The display switches to the title input display 6 Press the I lt or gt button to move the cursor 7 Press the BND button to select a character type Each time you press the BND button the character type changes in the following order Capital letters Numbers Symbols gt Umlaut Capital letters 8 Press the A or V button to select the desired character 9 Repeat steps 6 to 8 to enter up to 10 characters for the title 10 Press and hold the PI button 2 sec to store the title into memory Clearing titles 1 Select and play a CD in the CD changer for which you want to clear the title 2 Press and hold the DISP button 1 sec 3 Press the I lt or bb button to select TITLE INPUT 4 Press the MI button The display switches to the title input display 5 Press and hold the BND button 1 sec All characters in the title disappear 6 Press and hold the PI button for 2 sec to store the setting AUX function This system has an external input jack on the front panel so you can listen to sounds and music from external devices connected to this unit Selecting AUX IN sensitivity Make the following settings to select the sensitivity when sounds from external d
49. r OFF ON PTY in the display lights and PTY standby mode is turned on When the selected PTY broadcast starts the PTY item name appears in the display e OFF PTY in the display goes off and PTY standby mode is cancelled 4 Press the DISP button to return to the previous mode Cancelling a PTY interrupt broadcast Press the TA button during the PTY interrupt broadcast the PTY interrupt is cancelled and the unit returns to PTY standby mode Selecting PTY 1 Press and hold the DISP button 1 sec to switch to the Radio Data System adjustment selection display Press the k44 or gt button to select PTY SELECT Press the II button Press any one of the DIRECT buttons Alternatively press the A or V button to select the desired PTY Press the DISP button to return to the previous mode Below are the factory default settings stored for the DIRECT buttons The PTY select mode is cancelled automatically 7 seconds after a PTY is selected PTY seek 1 Press and hold the DISP button 1 sec to switch to the Radio Data System adjustment selection display Press the k44 or gt button to select PTY SELECT Press the I button Press the PP button to search for a PTY broadcast in the direction of higher frequencies press the 4 button to search in the direction of lower frequencies If no station with the selected PT
50. sec to store the message and the message return to default setting Setting the method for title scroll Set how to scroll in CD TEXT MP3 WMA AAC title The factory default setting is ON 2 1 Select SCROLL 3 1 Press the A or V button to select ON or OFF ON To scroll automatically OFF To scroll just 1 time When you want to see the title again in the title mode press and hold the DISP button 3 sec to scroll the title Setting the dimmer control You can set the dimmer control ON or OFF The factory default setting is ON 2 1 Select DIMMER 3 1 Press the A or V button to select ON or OFF Anti theft indicator The red Anti theft indicator is a function for prevent theft When the ACC or POWER is off this indicator blinks The factory default setting is OFF 2 1 Select BLINKLED 3 1 Press the A or V button to select ON or OFF Setting the external amplifier The factory default setting is OFF 2 1 Select A CANCEL 3 1 Press the A or W button to select ON or OFF ON Use with connected AMP OFF Use with inside AMP CX609E 23 Operations Common to Each Mode e Cellular phone interrupt setting If you connect this unit and your cellular phone with a separately sold cable you can listen to your telephone calls on your car speakers The factory
51. t S W VOL 3 1 Press the A or W button to increases or decreases the subwoofer volume The factory default setting is 0 Adjustment range 6 to 6 Adjusting the HPF 2 1 Select HPP 3 1 Press the A or V button to select as following order THROUGH 60 gt 90 gt 120 The factory default setting is THROUGH Setting the BBE MP Sound Enhancement and Restoration for compressed audio files BBE MP Minimized Polynomial Non Linear Saturation Process improves digitally compressed sound such as MP3 by restoring and enhancing the harmonics lost through compression BBE MP works by regenerating harmonics from the source material effectively recovering warmth detail and nuance This fuction is effective for the audio files in the CD MP3 WMA AAC or USB iPod mode but it is ineffective for the video in the USB iPod mode 1 Press the LJN button to switch to the sound adjustment selection display 2 Press the I or gt button to select BBE MP 3 Press the A or V button to select ON or OFF The factory default setting is OFF 4 When you select ON press the I button then press the A or V button to select as following order LOW gt MID gt HIGH Notes e Manufactured under license from BBE Sound Inc e Licensed by BBE Sound Inc under one or more of the following US patents 5510752 5736897 BBE and BBE s
52. t of compatible Apple iPod unit with the this model please contact your Clarion dealer or www clarion com e Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards iPod and iTunes are trademarks of Apple Inc registered in the U S and other countries Connecting an iPod When an iPod is connected to the USB slot Shuffle set on the iPod will become as follows e Shuffle Albums play Random play e Shuffle Songs play All random play The iPod has two modes the Play mode and the iPod menu mode for selecting tracks Switch between these modes by pressing the BND button for 1 second or longer Note e To connect iPod please use the USB cable attached in iPod Select iPod mode 1 Press the SRC button Playback will begin from the last file that was played on the iPod Notes e The following operations in Play mode operate the same as in CD mode Track selection 44 gt gt I Fast forward fast backward k44 gt gt Pause PI See CDIMP3 WMA AAC Operations page 15 17 for details e After a Podcast file has completed playback the pause display or the track end position Play Time display will appear At that time
53. ttons e Store radio stations in memory or recall it directly while in radio mode CD SLOT e Insert CDs here 4 EJECT button e Press to eject disc a Y TA BND AUX DISP button e Switch display mode AUX input jack e Input jack for connecting external device BND button Change bands or select seek tuning or manual uning while in the radio mode TA button Press to set the TA Traffic Announcement standby mode A W buttons e Select folders while in MP3 WMA AAC USB mode ROTARY knob e Roatate to adjust the volume K4 gt buttons e Commence fast forward or fast reverse mode J SOUND button Press to switch to the sound adjust mode SRC button e Turn the power on or off CX609E 5 4 REMOTE CONTROL Functions of Remote Control Unit Buttons If you buy the RCB 176 301 sold separately you can enjoy the use of the Remote control functions Some buttons on the remote control unit have different functions from the corresponding buttons on the main unit Signal transmitter SRC BND gt I a V kd gt gt MUTE DISP TA PTY PS AS AF clarion WIRELESS REMOTE CONTROLLER S g e Shared modes PTY button SRC button Press to cancel a PTY broadcast during a e Use to alternate operation mode among the PTY interrupt various modes DISP button Press to cancel a traffic announcem
54. umbers directly via the car stereo Telephone number uses 0 1 2 3 4 5 6 7 8 9 and 1 Press the BND button to select DIAL NUMBER 2 Press the MI button 3 Press the A or W button to select the numbers 4 Press the I or PP button to input or delete the number 5 Press and hold the button 1 sec to ENT call the mobile phone No Press the L N button to end the call e Call from Phonebook User can search the contact name in the phonebook and make call Alternatively user can call from mobile phone 1 Press the BND button to select PHONE BOOK 2 Press the PP button to enter the contact name mode In this case use the A W button to select the desired contact name 3 When the contact name is displayed press the PP or 4 button to select the contact name s phone number 4 Press the button to call the mobile phone No Press the L N button to end the call Answering a call 1 You can answer an incoming call by pressing any button Press the L N button to reject an incoming call Received Dialled Missed Call History You can search any Received Dialled Missed Call History 1 Press the BND button to select HISTORY 2 Press the gt P button to enter the contact name mode In this case use the A W button to select the desired contact name 3 When the contact name is displayed press the I or pl butt
55. umidity and some of CD R and CD RW discs may not be played Therefore do not leave them for a long time in the car e Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen Display Screen In extreme cold the screen movement may slow down and the screen may darken but this is normal The screen will recover when it returns to normal temperature 4 CX609E 3 CONTROLS Names of the Buttons and Their Main Functions Source unit CD SLOT DIRECT DIRECT Clarion SCN RPT RDM Bluetooth _ 7 ADJ DISP cx609E MP3 WMA AAC HIGH POWER S0Wx4 alow ZF ma gt gt SRC 5 ROTARY NI button e Perform preset scan while in radio mode e Play or pause a track while in CD MP3 WMA AAC USB iPod mode IR RECEIVER button e Receiver for remote control unit Operating range 30 in all directions RDM button e Perform random play while in the CD MP3 WMA AAC USB iPod mode RPT button e Perform repeat play while in CD MP3 WMA AAC USB iPod mode SCN button e Perform scan play while in CD MP3 WMA AAC USB mode DIRECT bu
56. vable stations cannot be received a previously stored station remains unoverwritten at the memory position 1 Press the BND button and select the desired band FM or AM MW LW 2 Press and hold the MII button 2 sec The stations with good reception are stored automatically to the preset channels If auto store is performed in the FM bands the stations are stored in FM3 even if FM1 or FM2 was chosen for storing stations Preset scan Preset scan receives the stations stored in preset memory in order This function is useful when searching for a desired station in memory 1 Press the I button 2 When a desired station is tuned in press the PH button again to continue receiving that station Note Be careful not to press and hold the MI button 2 sec otherwise the auto store function is engaged and the unit starts storing stations CX609E 1 1 Radio Data System Operations Radio Data System This unit has a built in Radio Data System decoder system that supports broadcast stations transmitting Radio Data System data When using the Radio Data System function always set the radio to FM mode AF function The AF function switches to a different frequency on the same network in order to maintain optimum reception The factory default setting is ON 1 Press and hold the DISP button 1 sec to switch to the Radio Data System adjustment selection display
57. ymbol are registered trademarks of BBE Sound Inc e During SOUND adjustment mode if no operation is performed for more than 10 seconds this mode can be cancelled and return to previous mode 1 0 CX609E CT Clock Time function The CT function receives CT data sent from an Radio Data System station and displays the time If a CT data is not being received CT appears in the display Note e CT data is not transmitted in some countries and by some broadcast stations Also in some areas the CT may not display accurately Radio Operations Listening to the radio 1 Press the SRC button and select the radio mode The frequency or PS and PTY appears in the display PS Programme service name PTY Programme type 2 Press the BND button and select the radio band Each time the button is pressed the radio reception band changes in the following order FM1 FM2 FM3 AM MW LW FMI Tuning 3 types of tuning mode available seek tuning manual tuning and preset tuning Seek tuning 2 types of seek tuning DX SEEK and LOCAL SEEK DX SEEK can automatically tune in to receivable broadcast stations LOCAL SEEK can tune in to only broadcast stations with a good reception sensitivity If MANU is lit in the display press and hold the BND button for 1 second or longer MANU in the display goes off and seek tuning is now available If TA is lit

Clarion CX609E Car Stereo System User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents