Carrier Access KTA Network Card User Manual
Contents
1. 3 2 1 Configuring Network Parameters from Telephone Handset Without PC users and network technician can set parameter through ordinary phone and KTA all those operations can be finished under VoIP model Instrucitons for network parameter setting Command Format Every configuration command from your telephone handset will be similar to the following format xxxxx Commands are a minimum of 3 digits If a command is prefixed by then the command is a query If the command is prefixed by just then it is a programming command Use HF to cancel a command If the command is successful you will hear di du If the command is unsuccessful you will hear du du du Common commands Note Each Command below is followed by its alphanumeric representation to make it easy to remember Query IP Address pick up phone handset and key in 047 or 0IP Set IP address pick up handset and key in 73847 xxx xxx xxx xxx or SETIP XXX XXX XXX XXX Enable DHCP pick up handset then key in 3427 or DHCP Disable DHCP pick up handset then key n 3427 or DHCP Reboot pick up handest then key in 778 or RST Restore default settings pick up handset then key in 358 or DLT Using H 323 pick up handset then key in 4323 or H323 Using SIP pick up handset then key in 747 or SIP Using adjusting IP pick up handset then key in 3228 or FACT IP type is STATIC IP IP address 192 1682. default value if forget KTA login password Pasword will restore to the default value 1234 gt Upgrade Click Update Firmware of the right bottom of setting page Save Settings Update Firmware Update Digitmap Restore Defaults KTA would automatically reboot after uprading then please press keys on the phone as 358 DLT to restore default settings and reboot again Note If you have been instructed to use the Upgrade Tool to perform the upgrade then you will need to enable Remote Access Permission This is done from your telephone handset by dialing 767 Please remember that after you have completed the upgrade then you should restore the KTA s default settings by dialing 358 on your phone handset and then wait for the KTA to reboot gt Other buttons Save Settings Update Firmrare Update Digitmap Restore Defaults save any changes Update degitmap restore the settings to you have made the original factory 4 Functions O Making and Receiving calls Oo Use Digitmap e Call Forwarding 4 1 Making and Receiving calls 4 1 1 Making outgoing calls A Calling VoIP Every VoIP Terminal will be assigned a VoIP number Users can directly call each other s number Example A user with the number 6667777want to call another user with the number 7778888 User 6667777 simply pick up the phone handset waits for dial tone and dial 7778888 followed by B Calling a regular phone a Calling a
3. 1 100 Gateway IP 192 168 1 1 Subnet mask 255 255 255 0 Note After performing each of the above commands the KTA will reboot You should wait until your telephone rings once to indicate that the reboot process has been completed Notice DHCP is a default setting of KTA Series 3 2 2 Configuring Network Parameters from Web Browser Open your web browser and enter the IP Address that has been assigned to the KTA if necessary use the Query IP Address command in the above section Log in page will be displayed The default password s 1234 Browser such as Microsoft Internet Explorer of Windows operating system to set up parameters After network connection please pick up handset press key 047 to hear IP address of the adaptor box In the address field of browser type the IP address and press ENTER to display the Settings page A log n page will be shown Enter log n password to set parameters The default password s 1234 If adaptor box cannot get IP enter 3427 to cancel DHCP mode After reset and beep sound heard please pick up the handset enter F73847 xxx xxx xxx xxx P to set IP address of adaptor box Get the IP address and use browser to set up fio 167 1T 240 255 255 254 0 fio l t 16 1 fio 16T 16 1 202 96 194 133 00 09 45 03 43 4e EE a nn a Update Firmware Update Digitmap Restore Defaults gt Network Settings Depending on the requirement of your ISP or Network you
4. Adapter KTA Series User Manual 1 ALL OA US ION at O ee VS Tt a a AN 3 SN ee SER eee eet ore nS Tee Sen MS E 3 A A E E E E EEE EE E ETETE 3 A O EONA 4 2 APP IU AAA e og 4 3 Installation and SEUA A A AA AAA AA AAA 4 Sal INstallaton 22222 een ars ne eee ee Tera 4 2 AA A OR Be ee 5 3 2 1 Configuring Network Parameters from Telephone Handset ee 5 3 2 2 Configuring Network Parameters from Web Browser cnennenenennennenn 5 A FUCO hs eer ane ANTRAT enn an A E E e Tene aun RER TEEN erica TRAUN ARENA FEIERN Seen ete ket ene ae tee 9 4 1 Mak ins and Reee yins CANIS an ae 9 Are Mak ME OS ON SC a a N ee 9 A RECI aia 10 ELSE MSI I I adnan ET OO 10 4 30 A CLIC NS nee ea el eser 10 Di Technical Parameler nun en een een N euere 11 3 1 TNE CICCUONIC SPECI ICAL ons a ee ee 11 D2 VV OFAN SUOMI environment 11 SA A OR e 12 6 Frequent Problems and SOlUMONS ae Eee 12 FT ePID CUCU A O A II A A thi tieh Rood tenses oat anteater arent 12 Mh Features unse A lee St oh tate eat haere tester needy 12 1 2 Standards and ASteeMentS unten 13 7 3 Recommend Usage netc ndtion an 13 7 4 Commands For Setting Network Parameters eesesnsensnennennensnennennnnnnn nenn 13 1 Introduction KTA series 1s one of VoIP terminal products with one port connecting with regular PSTN terminal devices and one port connecting with Internet It transfers voice through net By the management of soft switch platform
5. and the support of telecom KTA can communicate with VoIP terminals and dial to regular phone inexpensively KTA series port e KTA1000 s port One LAN port 10 Base T One PC port 10 Base T One PHONE port FXS The relation between LAN port and PC port is not router but hub eo KTAIOOL s port One LAN port 10 Base T One PHONE port FXS e KTAI010 s port One LAN port 10 Base T One PC port 10 Base T One PHONE port FXS One LINE port FXO KTA1010 has HUB function The relation between LAN port and PC port is not router but hub e KTAIOI1 s port One LAN port 10 Base T One PHONE port FXS One LINE port FXO 2 Sketch 2 1 Ports figure 1 2 Setup Button 3 PC port 10 Base T Ethernet RJ45 port to connect with PC only for KTA1000 KTA1010 4 LAN port 10 Base T Ethernet RJ45 port to connect with Internet or Local Network 5 PHONE Port FXS 6 LINE Port FXO only for KTA1010 KTA1011 Power Port 2 2 LED Indicators O O O O RX Service Phone MSG Power Power On LED TX Network data being transmitted RX Network data being received Service connected Remains illuminated when successfully logged on to server Service Phone phone in operation phone in used when light on means working under VoIP when light off means working under PSTN MSG unanswered call LED unanswered call appeared if light on 2 3 Application figure Internet
6. can configure the KTA with a Static IP DHCP or PPPoE DO ca a y SS a 202 96 199 133 o0 09 45 0a 43 4e Static IP If your ISP Network requires the use of a Static IP then you will be required to complete all of the parameters listed below Fill in subnet mask Fill n default gateway Ip local ip fio 161 17 235 subnet mask 255 266 264 0 fio 16T 16 1 HS fio 16T 6 1 INS 202 96 194 133 00 09 45 0a 43 4e DHCP If your router or other network device is configured to allocate an IP address to the KTA automatically then you can simply set the KTA up for DHCP operation and no other network parameters need to be completed fio 16T 17 235 255 255 254 0 fio 16T 16 1 fio 167 16 1 202 96 199 133 00 09 45 0a 43 4e PPPoE If your ADSL modem or other network device does not allow you to configure PPPoE then you may need to configure this in the KTA You will need to enter your PPPoE Username ID and Password as follows Fill in PPPoE id Fill in PPPoE psssword local ip LO l r 11 235 255 255 254 0 fio Mote daal ms fi AAA Ha 202 96 199 133 00 09 45 60 60 60 mac 00 09 45 0a 43 48 mac display the KTA s unique mac address Instruction if you can t choose corresponding net link please consult to network administrators or ISP and you may know which method is your network using and then make the right settings gt Protocol Settin
7. eter 5 1 The electronic specifications Oo Voltage 12V DC 500mA O Power adapter AD DC input 100 120V USA Japan etc or 220 240V China Europe etc or 100 240V 47 63Hz eo Network interface IEEE 802 3 10 Base T eo EMC FCC Partl5 CLASS B 5 2 Working storing environment O Operational temperature O to 50 C 32 to 122 F o Storage temperature 30 to 65 C 22 to 149 E 11 e Humidity 10 to 90 no dew 5 3 Dimensions O 166 4x 119x 31 6mm L x W x H 6 Frequent Problems and Solutions Probably Causes Unacceptable voice Bandwidth lt 30Kbps Using in network environment as quality under VoIP Unstable network quality stable and qualified as you can Delay gt 500ms or jitter gt 100ms or package loss gt 10 Login server failed Login failed by firewall Check with the service center of Service LED off Network provided by ISP and service carrier the ISP restricts log n Incorrect account information Using initial account to reset or phone number account number pin and phone number If the pin had been changed asking the service carrier Incorrect server address If server address had been changed asking the service carrier Failed to receive and dial Phone line provided by the Plug the phone line to the KTA the PSTN phone through Telecom service carrier s not LINE port FXO the phone line provided be plugged to the KTA LINE by the Telecom service port FXO carrier Inco
8. gs Service port H323 1719 default DNS or IP of the servicecarrier s soft switch Select protocol sip or h323 Sip 5060 default protocol 10 167 16 8 J _ serrice port 1715 E PE 1 phone munber 40018 pin Phone number User name with service provider Instruction Depending on your service provider the KTA may display gk zone instead of service address E m E fi mn E E Notice If login failed contact your service carrier to adjust parameters Do not ajust default value in most cases gt Audio Settings pemring dtmf 2 dtmf 3 dtmf4 dtmf5 dtmf 6 dtmt T dtmf i dtmf 9 not disturb Audio codec e7295 user define Ringtype A Voice active auto gain auto echo detection control cancellatio Notice All above audio parameters are default settings Contact your operator to adjust the corresponding parameters if any problems Please do not adjust these without the advice of your service provider gt Other Settings adjust the login passport IP address of network 1234 s default value time server Use Digitmap Please leave this function turned on The Digit map enables the KTA to recognize dialing sequences from around the world If the user dials a recognized dialing sequence then the KTA initiates the call without the user having to press the key after dialing Notice Enter 358 to restore factory
9. gt ISP SS Telecom LAN PHO Instruction KTA 1000 KTA 1001 without LINE port KTA1001 KTA 1011 without PC port 3 Installation and Setting 3 1 Installation 1 Locate your KTA close to your Internet connection and a power outlet 2 Plug the RJ 45 connector of the Ethernet 10 100Base T cable into the KTA s side input port 4 and plug the other s de into a hub or switch or wall ground socket of the structuring cable 3 Plug one side of the RJ 11 of phone line to the PHONE Port FXS of KTA plug another side of the phone line into user terminal phone line entrance to PABX etc 4 If you are the KTA1010 KTA1011 s user put the phone line to the LINE Port FXO of KTA you will have the both function of VoIP and PSTN 5 Plug the accessory power adapter into the power outlet then connect the output plug to power port Q of the KTA 6 Then waiting for KTA s startup after hearing short phone ring KTA is now working Notice Please select different type of Ethernet Cable according to the network devices devices connecting to LAN Select Straight through Ethernet Cable for network equipments router hub etc Select Cross over Ethernet Cable for the PC of ISP server Select the corresponding Ethernet Cable according to the instructions of XDSL and Cable Modem using Straight through Ethernet Cable in most casts 3 2 Configuration
10. ine the incoming call can be forwarded to a preset telephone number Settings Enter my account page on service website to set the forwarded number The number must accord with service carrier s dialing rule 10 User Information User ID WATT IP Phone Humber Balance US 222 00 PEFRE E Status Normal Payment ae Option Prepay Company 234 Contact Lan une 132132132 Please input the Number forwarding number Email BS5465 ncuid com Call forwarding i 6664747 number Please type in the target number which will be forwarded to Notice Call forwarding target number must be a PSTN number with more than 7 digits Example 1 If a U S service carrier s dialing rule To forward to a U S or Canada number please first dial 1 then the telephone number KTA user wants to make a call forward to 213 666 8888 please fill in 12136668888 Example 2 If a U S service carrier s dialing rule To forward to other countries regular numbers please first dial 011 then the country code no 0 as prefix and dial the telephone at last KTA user wants to make a call forward to 0755 88889999 please fill in 0118675588889999 Example 3 If a China service carrier s dialing rule To call other countries regular numbers please dial the district code and dial the telephone at last KTA user want to make a call forward to 0755 88889999 KTA user can fill in 075588889999 5 Technical Param
11. nt to Point Protocol of Ethernet DNS Domain Name Server FTP File Transfer protocol 00000000000O00O00O0O90 N HTTP Hyper Text Transfer protocol 3 Recommend usage net condition Delay Less than 400ms Jitter Less than 100ms Package loss Less than 10 Bandwidth More than 30Kbps 7 4 Commands For Setting Network Parameters Query IP Address 047 or 0IP Set IP address 73847 xxx xxx xxx xxx or SETIP Xxxx Xxx XXX XXx Enable DHCP 3427 or DHCP Disable DHCP 3427 or DHCP Reboot 778 or RST Restore default settings 358 or DLT Using H 323 4323 or H323 Using SIP 747 or SIP Using adjusting IP 3228 or FACT Safety Warning Please do not place this product near open flame or high temperature Avoid heavy 13 impact and do not leave the product in dump or highly humid conditions Current user manual is made based on the functions of present products if any content change has made no further notice 14
12. ountries regular numbers please dial the district code and dial the telephone at last KTA user calling a China regular number 0755 88889999 Pick up the handset when you hear the dial tone key in 075588889999followed by Under this situation functions are carried out through KTA s LAN port and PHONE port FXS 4 1 2 Receiving A Receiving VoIP When there is a call from other VoIP pick up handset or press handfree key B Receiving PSTN a Notice the function is only for KTA1010 KTA1011 and please plugs the phone line provided by telecom to the KTA LINE port FXO Under this situation when calls from the PSTN phone the phone then automatically changes to the PSTN model pick up the handset and the call can be successfully going on Functions are carried out through KTA s LINE port FXO b Notice it is only for the users except from a This is an optional service Only areas that are provided access numbers allow calls from a regular phone to KTA Please refer to Access Number List on the Carrier Service page to see if this service is available in your area 4 2 Use digitmap After you choose use digitmap through the web when you call the phone numbers all over the world after dial the number KTA can automatically dial out without pressing just as under PSTN model The rule will be defined by service carrier 4 3 Call Forwarding Every KTA has call forwarding feature when the user is not onl
13. regular phone under PSTN Notice Before this function can be realized please plug the phone line into the KTA LINE port FXO And now the phone is a VoIP phone Only for KTA1010 KTA 1011 Pick up the handset or press the handfree key then press the key to change into the PSTN model When you hear the dial tone key in the PSTN phone number after finishing calls put down the handset 1t automatically change to the VoIP model Under this situation functions are carried out through KTA s LINE port FXO b Calling regular phone under VoIP Notice It is applicable to all KTA users Every KTA can call any land or mobile phone anywhere in the world Please dial with the service carrier s dialing rule Press ff after you dial the phone number Example 1 If a U S service carrier s dialing rule To call a U S or Canada number please first dial 1 then the telephone number KTA user calling an U S Canada regular number 213 666 8888 Pick up the handset when you hear the dial tone key in 12136668888 followed by Example 2 If a U S service carrier s dialing rule To call other countries regular numbers please first dial 011 then the country code no 0 as prefix and dial the telephone at last KTA user calling a China regular number 0755 88889999 Pick up the handset when you hear the dial tone key in 0118675588889999 followed by Example 3 If a China service carrier s dialing rule To call other c
14. rrect dialing method Please dial the key before call then you can choose the phone line as the dial out line Login succeeded service Some wrong with KTA Press 778 RST to restore led on can t use phone momently KTA then reuse after picking up handset you cannot hear dial tone or press key without sound 7 Appendix 7 1 Features O Basic Port One or two RJ45 ports compatible with IEEE 802 3 10 Base T one FXS port one FXO port KTA 1010 KTA1011 AC DC adapter input 100 120V USA Japan etc or 220 240V China Europe etc or 100 240V 47 63 Hz Log in to specific soft switch platform Automatic searching for soft switch platform Supports DHCP Automatically obtain local IP subnet mask router IP Supports PPPoE 12 Voice active detection Comfortable noise generation Echo cancellation Dynamic buffer management minimize effect to voice quality caused by audio delay jitter Supports NAT Supports H 323 SIP Supports Remote Upgrade Supports Call Forwarding Lightningproof 2 Standards and agreements IEEE 802 3 10 Base T G 711A G 711u G 723 1 5 3K 6 3 Kbps and G 729 audio codec H 323 v2 and SIP TCP IP Internet Transport and Control Protocol RTP Real time Transport Protocol RTCP Real time Control Protocol VAD CNG Voice active detection comfortable noise generation G 165 Echo cancellation DTMF Tone Generate and Detection DHCP Dynamic Host Configuration Protocol PPPoE Poi
Download Pdf Manuals
Related Search