Carrier 1625 Air Cleaner User Manual
Contents
1. e Attach the quick connect terminals to the furnace EAC 1 and EAC 2 spade connections Attach the ground ring to furnace chassis ground NOTE The Infinity Air Purifier is to be powered by 115v 60 Hz NOTE The Infinity Air Purifier should only be powered when airflow is present The furnace control EAC spade connections provide power only when the furnace blower is operating If EAC connections are not available an alternative airflow sensing mechanism must be used to ensure the Infinity Air Purifier is only powered when airflow is present Contact a local Carrier distributor for information on approved alternatives A CAUTION UNIT COMPONENT DAMAGE HAZARD Failure to follow this caution may result in equipment damage or improper operation Black Lead Connect to HOT L1 or EAC 1 when provided White Lead Connect to Neutral L2 or EAC 2 when provided Green Ground Lead Connect to Appliance Ground Power Cord to EAC Terminals power cord to cabinet Power Supply Connector GZ Use wire ties to secure power cord to power supply enclosure Alternate Power Cord Pass Thru Hole Fig 7 Infinity Air START UP AND OPERATION Step 1 Checking Air Purifier Operation 4 WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death Before installing or servicing system always turn off main power to system There may be more than one 12. o o o A z A 3 16 4 p F p 13 16 Fig 10 Dimensions A05270 CARRIER CORPORATION FOR SERVICE OR REPAIR FOLLOW THESE STEPS IN ORDER FIRST Contact the installer You may find their name on the furnace or in your Homeowner s Packet If the installer s name is not known call your builder or home retailer if yours is a new residence SECOND Contact the nearest distributor See telephone yellow pages THIRD Contact Carrier Corporation Consumer Relations P O Box 4808 Syracuse New York 13221 Phone 1 800 428 4326 Model No Unit Serial No Date of Installation Installed by Name of Owner Address of Installation LIMITED WARRANTY FIVE YEAR LIMITED WARRANTY Carrier Corporation hereinafter referred to as Company warrants this product to be free from defects in material and workmanship If a defect is found within five years from date of original installation of product whether or not actual use begins on that date Company will provide a new or remanufactured part at Company s sole option to replace any defective part without charge for the part itself This warranty does not include labor or other costs incurred for diagnosing repairing removing installing shipping servicing or handling of either defective parts or replacement parts WARRANTY CONDITIONS 1 Warranties apply only to products in their original installation location 2 Installation use care and maintenanc
3. disconnect switch Attach the Infinity Air Purifier door to the cabinet A magnet in the door see Fig 9 is used to activate a safe ty switch in the power supply when the door is installed The power supply will not energize the air purifier un less the safety switch is activated Turn the HVAC system power on and adjust the thermostat or Infinity System Control to activate the system fan Turn the Infinity Air Purifier power switch to on position The power indicator light above the Air Purifier power switch should illuminiate see Fig 8 Check to ensure the light goes off when the Infinity Air Purifier power switch is set to off when the blower goes off or when the HVAC system power is turned off Step 2 Infinity Control a When the Infinity Air Purifier is used with an Infinity Control the Infinity Control can be configured to remind the homeowner when it is time to change the Infinity Air Purifier cartridge This maintenance reminder can be based on either the TrueSense dirty filter algorithm or time The installer should use their discretion to select the most appropriate option based on the initial system static pressure Step 3 Maximizing Performance a Maximum air purification performance is obtained when the furnace blower is set for continuous operation on the thermostat or Infinity Control Sample Furnace Circuit Board Pow
4. EAC terminals on a furnace electronic control If EAC terminals are not available an alternative airflow sensing mechanism must be used to ensure the Infinity Air Purifier is only powered when airflow is present Contact local Carrier distributor for information on approved alternatives Wia Enhancement Module x1 Safety Screen x1 Installation Components To in bag attached to power cord Return Duct Adapters Long x2 Short x2 Fig 2 Infinity Air Purifier Components A06027 INSTALLATION Step 7 Identify Mounting Location a Identify a mounting orientation for the Infinity Air Step 6 Check Intinity ae Furitier Components Purifier in the return air duct see Fig 3 C AUTI N b Ensure airflow direction through the Infinity Air Puri fier matches the arrows on the face of the air purifier cartridge The Infinity Air Purifier can be rotated 180 CUT HAZARD degrees to accommodate the cabinet orientation Failure to follow this caution may result in personal injury c The location of the Infinity Air Purifier should be Sheet metal parts may have sharp edges or burrs Use care readily accessible Enough TOOM should be provided for and wear appropriate protective clothing and gloves when periodic replacement of the air purifier cartridges handling parts A WARNING b Carefully remove all items from the box ELECTRICAL SHOCK AND UNIT DAMAGE HAZARD Failure to f
5. GAPA Infinity Air Purifier Sizes 1625 and 2025 Turn to the Experts Installation Start Up and Operating Instructions NOTE Read the entire instruction manual before starting the install This symbol indicates a change since the last issue TABLE OF CONTENTS Page INTRODUCTION 306 cis tee cas ce eee pee ee oe 1 HOW IT WORKS 4 ici coe Cee raed ceca o Enans 1 SAFETY CONSIDERATIONS 000 00 0000 1 APPLICATION CONSIDERATIONS 0 2 INSTALLATION ppe r EIN EEEE EEE RENTE 3 5 START UP AND OPERATION 0 0000 6 MAINTENANCE espressero erui a eat WER gee ea 6 TROUBLESHOOTING es reret kenop Eis 7 SPECIFICATIONS AND DIMENSIONS 8 WARRANTY eos coos hi 6 edd ee EEEE setae SS 9 INTRODUCTION Congratulations for selecting the Infinity Air Purifier for your home comfort system The Infinity Air Purifier is proven to remove and kill airborne germs and allergens including viruses bacteria and mold spores The Infinity Air Purifier is a cornerstone of Carrier s Healthy Home Solutions for providing healthier cleaner air in your home HOW IT WORKS The Infinity Air Purifier provides extremely high filtration performance while killing captured contaminants including viruses bacteria and mold spores The Infinity Air Purifier treats the entire air stream through a state of the art three stage process exclusive to Carrier In stage one the p
6. articles are electrically charged by a precision point ionization array as they enter the Infinity Air Purifier In stage two the charged particles are electrically attracted to the air purification cartridge which is located within an electric field In stage three captured particles are killed by electrical current flow and ion bombardment amp 0 SN Fig 1 GAPA Unit L A05265 SAFETY CONSIDERATIONS Improper installation adjustment alteration service maintenance or use can cause explosion fire electrical shock or other conditions which may cause personal injury or property damage Consult a qualified installer service agency or your distributor or branch for information or assistance The qualified installer or agency must use factory authorized kits or accessories when modifying this product Refer to the individual instructions packaged with the kits or accessories when installing Follow all safety codes Wear safety glasses and work gloves Have fire extinguisher available Read these instructions thoroughly and follow all warning or cautions attached to the unit Consult local building codes and National Electrical Code NEC for special requirement
7. d or designated by Company or damages resulting from their use Company products installed outside the continental U S A Alaska Hawaii and Canada Electricity or fuel costs or increases in electricity or fuel costs from any reason whatsoever including additional or unusual use of supplemental electric heat ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE WHATSOEVER Some states do not allow the exclusion of incidental or consequential damages so the above limitation may not apply to you NOOR OW N This Warranty gives you specific legal rights and you may also have other rights which vary from state to state Catalog no 49004DP45 2 06 Copyright 2005 Carrier Corp 7310 W Morris St e Indianapolis IN 46231 Printed in China Edition Date 3 06 Catalog No GAPA 2SI Manufacturer reserves the right to change at any time specifications and designs without notice and without obligations Replaces GAPA 1SI 10
8. e must be normal and in accordance with instructions contained in the Owner s Manual and Company s service information 3 Defective parts must be returned to the distributor through a registered servicing dealer for credit 4 All work shall be performed during normal working hours LIMITATIONS OF WARRANTIES ALL IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN AND APPLIES SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS SO THE ABOVE MAY NOT APPLY TO YOU THE EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED ENLARGED OR CHANGED BY ANY DISTRIBUTOR DEALER OR OTHER PERSON WHATSOEVER COMPANY WILL NOT BE RESPONSIBLE FOR 1 Normal maintenance as outlined in the installation and servicing instructions or Owner s Manual including filter cleaning and or replacement and lubrication Damage or repairs required as a consequence of faulty installation misapplication abuse improper servicing unauthorized alteration or improper operation Failure to start due to voltage conditions blown fuses open circuit breakers or damages due to the inadequacy or interruption of electrical service Damage as a result of floods winds fires lightning accidents corrosive environments or other conditions beyond the control of Company Parts not supplie
9. er Supply Connector Use terminals to connect the power cord wires to the furnace EAC 1 amp 2 amp ground terminals OOHO honno EAC 1 TERMINAL A06030 Purifier Electrical Connections Power Indicator gt gt A06052 Fig 8 Power Indicator MAINTENANCE The Infinity Air Purifier is designed to require no cleaning Maintenance is limited to the replacement of the air purification cartridge Frequency of air purifier cartridge replacement may vary depending on ductwork design and local environmental conditions To replace the air purifier cartridge complete the following steps Step 1 Turn the heating and cooling system off A WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death Before installing or servicing system always turn off main power to system There may be more than one 1 disconnect switch Step 2 Turn the Infinity Air Purifier switch to the off position Step 3 Remove the Infinity Air Purifier door Step 4 Slide out the old air purifier cartridge and discard Step 5 Install the new air purifier cartridge NOTE Make sure that the arrows on the air purifier cartridge point t
10. nstall atomizing humidifiers downstream of the air purifier because hard water salt deposits and water droplets may damage air purifier If an atomizing humidifier must be mounted upstream of the Infinity Air Purifier it should be mounted as far upstream as possible at least 6 ft recommended and a standard disposable furnace filter should be mounted between the humidifier and the air purifier to trap hard water salt deposits and water droplets SL Door x1 Cabinet x1 EZ Duct Gasket Tape 1 roll a Installation Manual Air Purification Cartridge x1 Furnace Adapters x2 Transitions If the return air duct or furnace openings do not fit the Infinity Air Purifier cabinet openings gradual transitions are recommended to reduce air turbulence and maximize efficiency No more than 20 degrees about 4 in per running ft of expansion should be used on each side of the transition fitting Turning Vanes If the Infinity Air Purifier is installed adjacent to a 90 degree duct elbow turning vanes should be added inside duct to improve air distribution across the face of the air purifier Electrical Power The Infinity Air Purifier should only be powered when airflow is present The furnace control EAC terminals provide power only when the furnace blower is operating Infinity Air Purifier models GAPAAXCC1625 and GAPAAXCC2025 are designed to be powered from the electronic air cleaner
11. ollow this warning could result in personal injury or death Only a trained experienced service person should install the Infinity Air Purifier A thorough check of the unit installation should be completed before unit operation Before performing installation service or maintenance operations on unit turn off all power to unit Tag disconnect switch with lockout tag NOTE Mounting on this side requires the cabinet to be rotated 180 for correct air flow Airflow Le VAN z Airflow Upflow Furnace with Bottom Mount Downflow Furnace with Top Mount Horizontal Application A06028 Fig 3 Infinity Air Purifier Cabinet Orientation Step 8 Mount the Cabinet 4 WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death Before installing or servicing system always turn off main power to system There may be more than 1 disconnect switch A CAUTION UNIT DAMAGE HAZARD Failure to follow this caution may result in equipment damage Cabinets will support a maximum weight of 400 Ibs when installed beneath a vertical furnace or air handling unit When setting furnace on cabinet do not drop it into place Position the furnace correctly on the cabinet to prevent a corner from slipping down and damaging the cabinet or its components a Turn off power to the heating and cooling sy
12. oward the furnace This should be in the same direction as airflow Step 6 Replace the Infinity Air Purifier door Step 7 Turn the Infinity Air Purifier switch to the on position Step 8 Turn on the heating and cooling system Door Switch Magnet A06053 Fig 9 Door Switch Magnet TROUBLESHOOTING A CAUTION SAFETY HAZARD Failure to follow this caution may result in personal injury or equipment damage The following instructions are for use by qualified personnel only 4 WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death The following procedures will expose electrical components Disconnect power between checks and proceed carefully The Infinity Air Purifier is equipped with a power indicator light located on the door see Fig 8 This power indicator light will illuminate when the Infinity Air Purifier door is installed the power switch is in the on position AND the furnace blower is running If the power indicator light is not illuminated follow the troubleshooting steps below Step 1 Check that the Infinity Air Purifier door is installed NOTE A magnet in the door see Fig 9 is used to activate a safety switch in the power supply when the door is installed The power supply will not ene
13. rgize the air purifier unless the safety switch is activated Step 2 Check that the Infinity Air Purifier power switch is in the on closed position Step 3 Confirm that the furnace blower is operating NOTE Power will not be supplied to the Infinity Air Purifier from the furnace controls EAC terminals unless the blower is running Step 4 Confirm that power provided from the furnace control EAC terminals is being conducted through the wiring to the Infinity Air Purifier power supply Step 5 If all of the above steps are completed and the power indicator light is still not illuminating replace the power supply on the enhancement module Note that there are no serviceable parts within the power supply Table 2 Specifications and Dimensions Specifications GAPAAXCC1625 GAPAAXCC2025 Color Taupe Metallic Taupe Metallic Cabinet Material 20 Ga Powder Coated Steel 20 Ga Powder Coated Steel Electrical 115v 60 Hz from furnace EAC terminals 115v 60 Hz from furnace EAC terminals Maximum Airflow CFM 1600 2000 Efficiency Equivalent to MERV 15 Equivalent to MERV 15 Replacement Cartridge GAPCCCAR1625 GAPCCCAR2025 Dimensions GAPAAXCC1625 GAPAAXCC2025 A 18 3 8 21 7 8 B 15 1 8 18 5 8 Cc 11 1 8 11 1 8 D 17 1 2 21 E 22 1 8 22 1 8 F 25 1 4 25 1 4 1 15 16 7 1 3 16 7 16 Typical Top amp Bottom
14. rs x2 Sy Ne Return Duct ASS Adapters x4 7 1 t lt f 1 i t t Return Duct Top Mount Bottom Mount Side Mount A06029 Fig 4 Mounting Infinity Air Purifier Cabinet Furnace 7 Adapters Airflow A05274 Fig 5 Use of Furnace Adapters Z 3 Note optional Slip return duct adapters onto flanges on air return duct side Al A05277 Fig 6 Use of Return Duct Adapters Step 9 Wiring 4 WARNING ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death Before installing or servicing system always turn off main power to system There may be more than 1 disconnect switch 4 CAUTION EQUIPMENT DAMAGE HAZARD Failure to follow this caution may result in equipment damage or improper operation This unit cannot be powered directly from blower motor leads Voltages can exceed 190 VAC 120v motors Do not wire directly to blower motor Wiring to blower motor will damage power supply and void warranty a Ensure power has been removed from the heating and cooling system b Turn the Infinity Air Purifier power switch off c Connect the power cord to the power supply connector see Fig 7 d Route the power cord through nearest cabinet hole and protect with enclosed cable connector Zip ties have been enclosed to secure the power cord to the side of the power supply
15. s It is important to recognize safety information This is the safety alert symbol A When you see this symbol on the unit and in instructions or manuals be alert to the potential for personal injury Understand the signal words DANGER WARNING and CAUTION These words are used with the safety alert symbol DANGER identifies the most serious hazards which will result in severe personal injury or death WARNING signifies hazards which could result in personal injury or death CAUTION is used to identify unsafe practices which may result in personal injury or product and property damage NOTE is used to highlight suggestions which will result in enhanced installation reliability or operation APPLICATION CONSIDERATIONS The Infinity Air Purifier is designed for use in the return air duct of a forced air heating cooling and ventilation system Models GAPAAXCC1625 and GAPAAXCC2025 are specifically designed for use in systems with a forced air gas furnace Air Conditioning The Infinity Air Purifier should be installed in a system so that all the return air is circulated through the air purifier It should be located upstream of both the furnace and the air conditioning evaporator coil This will help keep the furnace and evaporator coil clean and prevent condensation from forming within the Infinity Air Purifier Humidifiers An evaporative humidifier can be mounted upstream of the Infinity Air Purifier It is best to i
16. stem b Remove the existing furnace filter and discard Excessive system static may result if the Infinity Air Purifier is used with other filtration devices c Remove the air purifier cartridge and enhancement module from the Infinity Air Purifier cabinet d Position the cabinet between the furnace and return air duct see Fig 3 and 4 A transition duct may be required e Furnace adapters have been included for installer convenience They are designed for top or bottom mount installations see Fig 5 f Return air duct adapters have been included for installer convenience They should be used to connect the upstream side of the air purifier cabinet to the return air duct see Fig 6 g Install foam tape between the furnace and the air purifier cabinet h Mounting holes are provided for ductwork and furnace attachment A CAUTION UNIT DAMAGE HAZARD Failure to follow this caution may result in unit damage Mounting holes are provided for duct work and furnace attachment The screws on the down stream side of the cabinet should be installed so that the screw heads are inside air purifier cabinet to prevent damage to the air purifier cartridge i Seal seams with tape or caulking after the Infinity Air Purifier cabinet has been secured Return Duct a Return Duct Adapters x4 Furnace Adapters x2 Y Furnace Adapters x2 to pte
Download Pdf Manuals
Related Search