Buffalo Tools CME35 Music Mixer User Manual
Contents
1. Block Left 9 Rubber Gasket 45 Nut M10 10 Flat Washer 6 46 Spring Washer 10 11 Spring Washer 6 47 Tipping Bar 12 Nut M6 48 Spring 13 Lower Drum 15 Axle Bracket 16 Wheel 17 Flat Washer 27 18 Cotter pin 5X40 19 Frame 20 Support Leg 21 Bolt M8X70 56 Relief Nut 22 Block Right 57__ Sirain Relief Rubber 24 O ring 59 Strain Relief Nut 25 Gear Guard Long 60__ Gasket Switch 26 Drive Shaft 61__ Switch 27 Sleeve pipe 62 Motor Cover 28 Cradle 63 Motor 29 O ring 32X2 65 64 Pulley 49 Washer 50 M10X60 51__ Tipping Bar 52 Handle Grip 53 M8X25 54 Plate 55 Power 30 Bearing cover 65 31 6206 66 6906 32 Circlip 30 67 Snap Washer Hole 47 33 Circlip 62 68 Sheet Metal Screw ST4 8X16 34 Lock Pin 5X45 35 Sheet Metal Screw ST3 5X16 36 Drive pinion 69 Washer Shaft 70__ End Plate 71 Bolt M8xX30 72 Motor Mount Bracket End Plate 73 Gasket OT CO ND e D BOOS CME35 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 82. Mount the mixing blades inside the bottom drum loosely as shown Two holes are provided at the base of the drum into which a M8X20 bolt may be inserted from the outside A leather washer flat washer lock washer and a nut should be threaded on loosely on the inside The leather washer should be placed under the blade down against the drum NOTE Two arrows are labeled on upper drum and bottom drum to make their position relation If you have any difficulty in correctly positioning the mixing blades it is helpful if you temporarily mount the upper drum on the top of the bottom drum rotating it so that the two arrows line up Figure F Position the upper drum on bottom drum over the rim making sure the mounting holes align in both as well as the labeled arrows Insert a M6X16 cross headed screw into each mounting holes in the rim Secure each bolt from below with a flat washer lock washer and nut Tighten all bolts 5 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 5 Secure the mixing blades to the upper drum by inserting two 8 16 cross headed screws from the outside through the holes in the drum A leather washer should be positioned inside between the drum and blade Secure the mixing blade on the inside using a flat washer spring washer and nut Finally ensure top and bottom mixing blade mountings are tight Figure G Position the adjusting plate and attach with bolts 8 X
3. parts cleaning or working on the mixer DO NOT FORCE TOOL Always work within the rated capacity Do not start the motor if the drum is fully loaded Do not turn mixer off while full of concrete Do not use the mixer for a purpose for which it was not intended The mixer is not to be towed by any vehicle NEVER LEAVE MIXER RUNNING UNATTENDED Do not leave mixer until it has come to a complete stop DISCONNECT POWER PROTECT THE ENVIRONMENT Take leftover materials to an authorized collection point or follow the stipulations in the country where the mixer is used Do not discharge into drains soil or water STAY ALERT Do not operate the mixer while under the influence of drugs alcohol or any medication that could affect your ability to use it properly Do not use this mixer when you are tired or distracted from the job at hand Watch what you are doing at all times Use common sense A WARNING This unit contains chemicals known to the state of California to cause birth defects and in some cases cancer California Health amp Safety code section 25249 5 et seq SERVICE Tool service must be performed only by qualified repair personnel Service or maintenance by unqualified personnel could result in a risk of injury When servicing a tool use only identical replacement parts and follow instructions in the manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of shock or inju
4. 201201 CME35 4 Cu Ft Cement Mixer Assembly amp Operating Instructions LP READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT This manual provides important information on proper operation amp maintenance Every effort has been made to ensure the accuracy of this manual These instructions are not meant to cover every possible condition and situation that may occur We reserve the right to change this product at any time without prior notice IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR UNSAFE DO NOT OPERATE THIS PRODUCT HAVE QUESTIONS OR PROBLEMS DO NOT RETURN THIS PRODUCT TO THE RETAILER CONTACT CUSTOMER SERVICE If you experience a problem or need parts for this product visit our website http Awww buffalotools com or call our customer help line at 1 888 287 6981 Monday Friday 8 AM 4 PM Central Time A copy of the sales receipt is required FOR CONSUMER USE ONLY FOR PROFESSIONAL USE KEEP THIS MANUAL SALES RECEIPT amp APPLICABLE WARRANTY FOR FUTURE REFERENCE Mixer Paddles GENERAL PRODUCT SPECIFICATIONS Drum Motor Cover SPECIFICATIONS 180 Ib Dry Mix Capacity Plugs Into 110 Volt Outlet noe 2 3 HP 15 Diameter Drum Opening Drum Tips 360 Degrees Seal Power Switch FEATURES Double Insulated S t Handles Two 90 6 Bags Of a Dry Cement Or Mortar Also Mix Feeds Fertilizers amp Potting Soil Wheel SAVE THESE INSTRUCTIONS FOR FUTURE REFERE
5. 25 x2 Figure H Slide the support arm over the adjusting plate and attach with bolts Place shaft at the leg end of frame with the rim facing inwards Secure with two M8X25 bolts each with a nut lock and flat washers Insert the spring into the bar pipe Hold it in place with a finger and place the bar over the larger diameter shaft so the shaft retains the spring Press down on bar until the holes in the bracket line up with the hole drilled Insert a hex bolt and screw on a nut with flat and lock washers from the other side Screw the nut up against the bracket firmly but not so tightly so as to prevent the bar from pivoting about the bolt Figure I Line up the motor and slide the transmission case over the pinion shaft Secure the case to the frame with four M8 nuts NOTE The bar must be allowed to pivot about the bolt so that the lugs on the bracket can be engaged or disengaged from the slots in the locking plate LOADING DRUM TILTING The spring loaded tipping bar with locking lugs provides easy control of the drum which can be locked in the Mix Discharge and Stored position The drum is locked in position by lugs on the self locating tipping bar which engages into the locking plate on the mixer frame To tilt the drum withdraw the tipping bar to disengage the locking lugs This allows the tipping bar and drum to be turned in the same direction Rotate the tipping bar until the locking lugs engage into the locking pl
6. NCE This manual contains important information regarding safety operation maintenance and storage of this product Before use read carefully and understand all warnings cautions instructions and labels Failure to do so could result in serious personal injury property damage or even death IMPORTANT SAFETY RULES COMMON SENSE AND CAUTION ARE FACTORS WHICH CANNOT BE BUILT INTO ANY PRODUCT THESE FACTORS MUST BE SUPPLIED BY THE OPERATOR A WARNING Keep your work area clean and well lit Cluttered work benches and dark work areas may cause accidents or injury Keep bystanders children and visitors away while operating the Cement Mixer Distractions can cause you to lose control A CAUTION Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users A WARNING Use common sense while operating this cement mixer Do not use this tool if you are e Feeling tired or are under the influence of alcohol or drugs Wearing loose clothing or jewelry Keep long hair pulled back and away from moving parts Overreaching or have improper footing Handling the tool in this way could cause serious injury Wear the proper safety equipment such as safety goggles dust masks non skid shoes etc Check to be su
7. ate on the mixer frame NOTE A built in thermal protector in the motor will prevent it from overheating The thermal protector restores automatically when the motor cools down MAINTENANCE Thoroughly clean the mixer at the end of each day s operation Keep your mixer clean The slightest trace of material left in the drum will harden and attract more each time you use it until the machine is useless Dried cement should be scraped out of the drum Do not throw bricks into mixer drum to clean it out Do not beat on the drum to break up accumulations of dried cement mix The drum may be scoured for approximately 2 minutes using 1 gravel and water mixture Discharge the gravel water mixture and hose down the drum assembly inside and out The drive belt is under constant tension by a spring loaded jockey No adjustment is required apart from a touch of grease on the spindle The bearings are sealed for life CME35 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 6 PARTS DIAGRAM PARTS LIST 5 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 1 Cross Headed Screw M6X16 4 37 Gpar Guard Short 2 Waterproof Washer 12 38 Circlip 42 FlatWasher8_ 2 39 202 2 4 Spring Washer 8 22 40 Circlip 15 5 Nut M8 22 41 Locknut 8 6 Upper Drum 42 Bolt8X65 7 Cross Headed Screw 6 16 43 Circlip 38 8 Mixing Blade 44
8. d places where vehicles might run over it Avoid allowing the extension cord to be trapped underneath the mixer Unroll it fully or it will overheat and could catch fire AVOID ELECTRICAL SHOCK Check that the electric circuit is adequately protected and that it corresponds with the power voltage and frequency of the motor Do not plug or unplug the motor while standing in or around damp or wet ground Do not use the mixer in wet or damp areas or expose it to rain Prevent body contact with grounded surfaces pipes radiators ranges and refrigerator enclosures Make sure your fingers do not touch the plug s metal prongs when plugging or unplugging the mixer DO NOT OVERREACH Keep proper footing and balance at all times when loading or unloading the mixer Never stand on mixer Serious injury could occur if the mixer is tipped Do not store anything above or near the mixer where anyone might stand on the mixer to reach them 5 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 3 AVOID INJURY FROM UNEXPECTED ACCIDENT Keep hands out of the way of all moving parts Do not place any part of your body or any tool like shovel in the drum during operation When operating do not pass hands through the clearance between frame and support arm or the one between the drum and support arm Never open the motor cover before unplugging the mixer Disconnect from power supply when not in use before moving making adjustments changing
9. re all adjusting keys or wrenches have been removed before use CME35 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 2 A WARNING Do not use the cement mixer if the switch does not turn it on and off Any tool that cannot be controlled with the switch is dangerous and must be repaired AVOID DANGEROUS CONDITIONS Make sure there is adequate surrounding workspace Keep your work area clean and well lighted Cluttered areas invite injuries Keep area around the mixer clear of obstructions grease oil trash and other debris which could cause persons fall onto moving parts Only use or operate the mixer on solid flat level ground that is capable to support the weight of the mixer and its load to prevent the mixer from tipping over Do not attempt to move the mixer when it is loaded and or in operation This mixer is intended for the production of concrete mortar and plaster It is not suitable for the mixing of flammable or explosive substances Do not use it in areas where fumes from paint solvents or flammable liquids pose a potential hazard INSPECT YOUR MIXER Check your mixer before turning it on Keep guards in place and in working order Do not plug mixer with motor cover off Check all bolts nuts and screws for tightness before each use especially those securing guards and drive mechanisms Vibration during mixing may cause these to loosen Replace damaged missing or failed parts before using i
10. ry Lower Drum PARTS DIAGRAM Upper Drum Hardware Frame Assembly 5 4 Cu Ft Cement Mixer Assembly amp Operating Instructions Manual 4 ASSEMBLY WARNING IT IS RECOMMENDED THAT TWO PERSONS ASSIST IN ASSEMBLY Figure A With a split pin inserted into the inner holes in each stub axle place a flat washer then a wheel followed by another flat washer Insert another split pin into the axle holes outside each flat washer Bend each side of the pins outward so they do not fall out Figure B With the frame lying on its side attach the support leg as shown Insert two M8X70 hex bolts through the holes from one side then flat washers lock washers and nuts from the other side Tighten down Figure C Turn the frame over and attach the axle bracket with wheels in the same manner 00 M8 x 70 Figure D Slide the bearing block on the shaft Hold it in place with 042 spiral ring Carefully and with two people set the bottom drum with support arm onto the side supports of the stand as shown so that the bearing blocks slot into the channels provided by the side supports The larger diameter shaft should be at the leg end of the stand At each side line up the holes in the side support with those in the bearing block and insert a M8X65 hex bolt from one side then a flat washer lock washer and nut from the other side Tighten with a wrench fm 006 M6 16 900 0 m8x16 2 Figure
11. t Do not wear loose clothing gloves neckties or jewelry rings wrist watches They can be caught in moving parts Protective electrically non conductive gloves and non skid footwear are recommended when working Wear protective hair covering to contain long hair preventing it from getting caught in machinery Wear a face or dust mask if the operation is dusty Always wear safety goggles and or face shields Everyday eyeglasses have only impact resistant lenses They are not safety glasses A WARNING Safety glasses and ear protection must be worn during operation Wear eye protection see ANSI 249 1 safety standard non conductive gloves and non skid footwear DO NOT ABUSE CORD Never carry mixer by cord or yank it to disconnect from socket Keep cord from heat oil amp sharp edges EXTENSION CORDS Extension cords must be no longer than 164 feet in length The wire section must be big enough to allow sufficient current flow to the motor Improper use of extension cords may cause inefficient operation of the mixer which can result in overheating and motor damage Only extension cords to HO7RN F specification intended for outdoor purpose may be used Avoid use of free and inadequately insulated connections Connections must be made with protected material suitable for outdoor use Make sure that any extension cord connections are dry and safe Ensure that the extension cord is carefully laid out avoiding liquids sharp edges an
Download Pdf Manuals
Related Search