BMW 550I Automobile User Manual
Contents
1. lt2. The water we use contains limescale If it becomes necessary use a water softener to remove limescales Use a special product made for washing machines Obey the instructions that you find on the packaging of the manufactur er Do this separately from the laundry wash EXTERNAL CLEANING Clean the appliance only with soap and warm water Fully dry all the surfaces CAUTION Do not use alcohol solvents or chemical products MAINTENANCE WASH With the low temperature programmes it is possible that some detergent stays in the drum Make regularly a maintenance wash To do this e Empty the laundry from the drum e Set the hottest cotton wash programme e Use a correct quantity of powder deter gent with biological properties After each wash keep the door open for a while to prevent mould and to let un pleasant smells go out DOOR SEAL Regularly examine the seal and remove all Xs objects from the inner part Y DRUM e Clean the drum with special product for Regularly examine the drum to prevent limescale and rust particles Only use special products to remove rust particles from the drum To do this stainless steel e Start a short programme for cotton at the maximum temperature with a small quantity of detergent DETERGENT DISPENSER ENGLISH 21 To clean the dispenser Press the lever Pull the dispenser out Remove the top part of the liquid
3. penser Start the programme to drain the wa ter FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 C remove the remaining water from the inlet hose and the drain pump 1 2 3 Disconnect the mains plug from the mains socket Close the water tap Remove the water inlet hose Put the two ends of the inlet hose in a container and let the water flow out of the hose Empty the drain pump Refer to the emergency drain procedure When the drain pump is empty install the inlet hose again AN WARNING Make sure that the temperature is more than 0 C before you use the appliance again The manufacturer is not responsi ble for damages caused by low temperatures TROUBLESHOOTING ENGLISH 25 The start of the appliance does not occur e EAU The appliance does not drain or it stops during operation the water First try to find a solution to the problem refer to the table If not contact the serv ice centre With some problems the acoustic signals operate and the display shows an alarm code Fig The appliance does not fill with EU The appliance door is open or not closed correctly WARNING Deactivate the appliance before you do the checks water Problem Possible cause Possible solution The appliance The water tap is closed Open the water tap does not fill with water The water inlet hose is Make sure that the wate
4. DE wool Hand washable Rinses RINSE HOLD 40 Cold wool and delicate Short spin ov Spin Drain4 fabrics with hand washing care sym bol max 2 kg All fabrics The maximum load of the laundry is related to the type of laundry Drainage of the water Spin phase at the maximum speed SPIN REDUCTION NO SPIN 12 www aeg com Programme Type of load Cycle Functions Temperature max weight of load description ns All fabrics One rinse with ad SPIN REDUCTION Rince ditive spin phase RINSE HOLD EXTRA RINSE R Set this programme Prewash SPIN REDUCTION to wash curtains It Wash RINSE HOLD ae adds automatically Rinses EXTRA RINSE Ee the prewash phase to Short spin clean the dust from the curtains Do not put the deter gent into the prewash compartment max 2 5 kg All items in jeans Jer Wash SPIN REDUCTION 5 sey made items with Rinses RINSE HOLD ae Le Id hi tech materials Short spin EXTRA RINSE F max 7 kg TIME SAVE2 2 Quick washing pro Wash SPIN REDUCTION S ick 7 gramme to be used Rinses RINSE HOLD Pl for lightly soiled Long spin EXTRA RINSE 5 white fast coloured cottons and mixed fabrics max 5 kg 20 Min 3 kg Cotton and synthetic Wash SPIN REDUCTION 40 30 items with light soil or Rinses worn only onetime Short spin SUPER ECO Mixed fabrics cotton Wash SPIN REDUCTION Cold and synthetic items Rinses RINSE HOLD max 3 kg Short spin EXTRA RINSE White and fast co
5. Door handle Rating plate Drain pump ACCESSORIES Feet for the appliance level Ei Water drain hose 9 Water inlet valve Mains cable Transit bolts Feet for the appliance level Spanner To remove the transit bolts Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts Anti flood inlet hose To prevent possible leakage Plastic hose guide To connect the drain hose on the edge of a sink CONTROL PANEL ENGLISH Ecos 0 De SUPER ECO Q amp LU 20 Min 3 kg 0 Q d8 ED RO Daw FO ti 00 OL I 168 UA n oo n On Off button 7 Programme knob Display Start Pause button Dll Delay start button Time save button 23 Extra rinse button Stain button Spin reduction button Temperature button BE GS ef see 6 ON OFF BUTTON Press this button to activate or deactivate the appliance A tune sounds when the appliance is activated The AUTO Stand by function automatical ly deactivates the appliance to decrease the energy consumption when e You do not use the appliance for 5 mi nutes before you press button J All settings are cancelled Press button f ll to activate the appli ance again S O EEG Set again the washing programme and all possible options e After 5 minutes from the end of the washing programme Refer to At t
6. To help the environment do not use more than the correct quantity of deter gent Obey the instructions that you find on the on packaging of these products e Use the correct products for the type and colour of the fabric the pro gramme temperature and the level of soil e If you use liquid detergents do not set the prewash phase e If your appliance has not the detergent dispenser with the flap device add the liquid detergents with a dosing ball WATER HARDNESS If the water hardness in your area is high or moderate we recommend that you use a water softener for washing machines In areas where the water hardness is soft it is not necessary to use a water softener To know the water hardness in your area contact your local water authority Obey the instructions that you find on the packaging of the products Equivalent scales measure the water hard ness e German degrees dH e French degrees TH e mmol l millimol for each litre interna tional unit for the hardness of water e Clarke degrees Water hardness Level Type dH 1 soft 0 7 T H 0 15 mmol l Clarke 0 1 5 0 9 Water hardness ENGLISH 19 Leve Type dH T H mmol l Clarke medium 8 14 16 25 1 6 2 5 10 16 hard 15 21 26 37 2 6 3 7 17 25 very hard gt 21 gt 37 S gt 25 20 www aeg com CARE AND CLEANING AN WARNING Disconnect the appliance from the mains supply before you clean it DESCALING
7. ad ditive compartment Clean all the parts with water Clean the dispenser recess with a brush Put back the dispenser in the recess DRAIN PUMP Regularly examine the drain pump and make sure that it is clean Clean the pump if The appliance does not drain the water The drum cannot turn The appliance makes an unusual noise because of the blockage of the drain pump The display shows an alarm code be cause of the problem with water drain WARNING 1 Disconnect the mains plug from the mains socket 2 Do not remove the filter while the appliance operates Do not clean the drain pump if the water in the appliance is hot The water must be cold before you clean the drain pump 22 www aeg com To clean the drain pump Open the drain pump door Put a container below the recess of the drain pump to collect the water that flows out Press the two levers and pull forward the drainage duct to let the water flow out When the container is full of water put the drainage duct back again and empty the container Do steps 3 and 4 again and again until no more wa ter flows out from the drain pump Pull back the drainage duct and turn the filter to remove it Remove fluff and objects from the pump Make sure that the impeller of the pump can turn If this does not occur contact the service centre ENGLISH Clean the f
8. the installa tion Make sure that there is access to the mains plug after the installation Do not pull the mains cable to discon nect the appliance Always pull the mains plug DISCARD THE APPLIANCE 1 Disconnect the mains plug from the mains socket Ree ee i i th 2 Cut off the mains cable and discard it w ee lk ce a bala ald 3 Discard the door catch This prevents children or pets to be closed in the Make sure that the electrical informa appliance There is a risk of suffoca tion on the rating plate agrees with the tion only for front loading applian power supply ces e Always use a correctly installed shock proof socket Do not use multiple plugs and exten sion cables There is a risk of fire TECHNICAL INFORMATION Dimensions Width Height Depth 600 850 522 mm Total depth 540 mm Electrical connection Voltage 230 V Overall power 2200 W Fuse 10A Frequency 50 Hz Level of protection against ingress of solid particles IPX4 and moisture ensured by the protective cover except where the low voltage equipment has no protection against moisture Water supply pressure Minimum 0 5 bar 0 05 MPa Maximum 8 bar 0 8 MPa Water supply 1 Cold water Maximum load Cotton 7kg Spin speed Maximum 1200 rpm L 70270 VFL 1400 rem L 70470 FL 1 Connect the water inlet hose to a water tap with a 3 4 thread 6 www aeg com PRODUCT DESCRIPTION Worktop Detergent dispenser Control panel
9. 12 Put the plastic caps in the holes You can find these caps in the user man ual bag i We recommend that you keep the packaging and the transit bolts for when you move the appliance If the appliance is delivered in the winter months when there are minus temperatures Store it at room temperature for 24 hours before using for the first time POSITIONING AND LEVELLING e Install the appliance on a flat hard floor e Make sure that carpets do not stop the air circulation below the appliance e Make sure that the appliance does not touch the wall or other units e Loosen or tighten the feet to adjust the level A correct adjustment of the appli ance level prevents the vibration noise and the movement of the appliance when in operation e The appliance must be level and stable CAUTION Do not put cardboard wood or equivalent materials below the appliance feet to adjust the level A THE INLET HOSE Do not use an extension hose if the inlet hose is too short Contact the service centre for the replace ment of the inlet hose i Water stop device ENGLISH 31 e Connect the hose to the appliance Turn the inlet hose only left or right Loose the ring nut to set it in the cor rect position e Connect the water inlet hose to the cold water tap with 3 4 thread CAUTION Make sure that there are no leaks from the co
10. Divide the laundry in white coloured synthetics delicates and wool e Obey the washing instructions that are on the laundry care labels e Do not wash together white and col oured items e Some coloured items can discolour with the first wash We recommend that you wash them separately for the first times e Button up pillowcases close zippers hooks and poppers Tie up belts e Empty the pockets and unfold the items e Turn inside out multilayered fabrics wool and items with painted illustra tions e Remove hard stains e Wash with a special detergent heavy soil stains e Be careful with the curtains Remove the hooks or put the curtains in a wash ing bag or pillowcase e Do not wash in the appliance Laundry without hems or with cuts Underwired bras Use a washing bag to wash small items e Avery small load can cause balance problems with the spin phase If this oc curs adjust manually the items in the tub and start the spin phase again STUBBORN STAINS For some stains water and detergent is not sufficient We recommend that you remove these stains before you put the items in the ap pliance Special stain removers are available Use the special stain remover that is applica ble to the type of stain and fabric Water hardness table DETERGENTS AND ADDITIVES e Only use detergents and additives spe cially made for washing machines e Do not mix different types of deter gents e
11. L 70270 VEL EN WASHING MACHINE USER MANUAL L 70470 FL 2 www aeg com CONTENTS TECHNICA CONTROL NOM A 14 LOADING 1 4 FILLING TH 16 SETTING A 7 ATTHE EN 8 20 CARE AND 25 TROUBLES 28 INSTALLAT SAFETY INFORMATION L INFORMATION PRODUCT DESCRIPTION PANEL PROGRAMMES 14 BEFORE FIRST USE 14 USING THE APPLIANCE HE LAUNDRY E DETERGENT AND ADDITIVES ND STARTING A PROGRAMME D OF THE PROGRAMME HINTS AND TIPS CLEANING HOOTING ION ENVIRONMENT CONCERNS Recycle the materials with the symbol amp Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol with the household waste Return the product to your local recycling facility or contact your municipal office VISIT OUR WEBSITE FOR Products Brochures User manuals Trouble shoote Service informa www aeg com LEGEND r tion N Warning Important Safety information General information and tips 8 Environmental information Subject to change without notice ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes re
12. ading to get the very best from it ACCESSORIES AND CONSUMABLES In the AEG webshop you ll find everything you need to keep all your AEG appliances looking spotless and working perfectly Along with a wide range of accessories designed and built to the high quality standards you would expect from specialist cookware to cutlery baskets from bottle holders to delicate laundry bags Visit the webshop at www aeg com shop CUSTOMER CARE AND SERVICE We recommend the use of original spare parts When contacting Service ensure that you have the following data available The information can be found on the rating plate Model PNC Serial Number 4 www aeg com AN SAFETY INFORMATION Before the installation and use read this manual carefully e For your safety and the safety of your property e To help the environment e For the correct operation of the appli ance Always keep these instructions with the appliance also if you move or give it to a different person The manufacturer is not responsible if an incorrect installation and use causes dam age CHILDREN AND VULNERABLE PERSON SAFETY e Do not let persons children included with reduced physical sensory reduced mental functions or lack of experience and knowledge use the appliance They must have supervision or instruction for the operation of the appliance by a per son who is responsible for their safety Do not let children play with the ap
13. ally deactivates the appliance i When you activate the appliance again the display show the end of the last set programme Turn the programme knob to set a new cy cle e Remove the laundry from the appli ance Make sure that the drum is emp ty e Keep the door ajar to prevent mildew and odours e Close the water tap The washing programme is completed but there is water in the drum The drum turns regularly to prevent the creases in the laundry The door stays locked ENGLISH 17 Open the appliance door Close the appliance door and press button Jj The programme or the delay start continues If the temperature and level of the water in the drum are too high the door lock symbol stays on and you cannot open the door To open the door do the steps that follow 1 Deactivate the appliance 2 Wait for some minutes 3 Make sure that no water is in the drum AN If you deactivate the appliance it is necessary to set the programme again You must drain the water to open the door To drain the water 1 2 If necessary decrease the spin speed Press the Start Pause button Jj The appliance drain the water and spin When the programme is completed and the door lock symbol goes off you can open the door Deactivate the appliance The appliance drain and spin au tomatically after approximately 18 hours 18 www aeg com HINTS AND TIPS THE LAUNDRY LOAD e
14. ash 30 C 0 25 45 1 Refer to the display for the programme time 2 The consumption information shown in this chart is indicative It can vary depending on the quantity and the type of laundry on the temperature of the water supply and on the ambient temperature Standard programmes for the Energy Label consumption values The cotton 60 C economy and cotton 40 C economy are the standard cotton pro grammes for normally soiled cotton laun dry They are suitable to clean normally soiled cotton laundry and they are the most efficient programmes in terms of combined energy and water consumption for washing that type of cotton laundry They agree with EN60456 The actual water temperature may differ from the declared cycle temperature 14 www aeg com BEFORE FIRST USE 1 To activate the drain system put 2 li tre of water in the main wash com partment of the detergent dispenser Put a small quantity of detergent in the main wash compartment of the USING THE APPLIANCE Open the water tap Connect the mains plug to the mains socket Press button fj to activate the appli ance LOADING THE LAUNDRY Open the appliance door Put the laundry in the drum one item at a time Shake the items before you put them in the appliance Make sure detergent dispenser Set and start a programme for cotton at the highest temperature without laundry This re moves all possible dirt from the drum and the tub 4 Put
15. ce 2 Press button J again to activate the appliance Now you can set a new washing programme The appliance does not drain the water CHANGE A FUNCTION You can change only some functions be fore they operate 1 Press button BMJ The indicator flash es 2 Change the function set SET THE DELAY START 1 Press button J again and again until the display shows the number of mi nutes or hours The related symbols comes on 2 Press button E the appliance starts the countdown of the delay start When the countdown is completed the programme starts automatically i Before you press button KS to start the appliance you can cancel or change the set of the delay start CANCEL THE DELAY START 1 Press button EM The related indica tor flashes 2 Press button J again and again until the display shows 0 3 Press button J The programme starts OPEN THE DOOR While a programme or the delay start op erates the appliance door is locked To open the appliance door 1 Press button BJ The door lock sym bol in the display goes off AT THE END OF THE PROGRAMME e The appliance stops automatically e The acoustic signals operate In the display 7 comes on e The indicator of the Start Pause button goes off e The door lock symbol goes off Press button fj to deactivate the ap pliance After five minutes from the end of the programme the energy saving function automatic
16. gent quantity or use a different one Problem Possible cause You did not remove the stubborn stains before you wash the laundry Incorrect temperature was set ENGLISH 27 Possible solution Use special products to remove the stubborn stains Make sure that you set the cor rect temperature Too much laundry load After the check activate the appliance The programme continues from the point of interruption If the problem occurs again contact the service centre If the display shows other alarm codes contact the service centre Decrease the laundry load 28 www aeg com INSTALLATION UNPACKING Use the gloves Remove the external film If necessary use a cutter Remove the cardboard top Remove the polystyrene packaging materials Remove the internal film Open the door and remove all the items from the drum 10 11 ENGLISH 29 Put one of the polystyrene packaging elements on the floor behind the ap pliance Carefully put down the appli ance with the rear side on it Make sure not to damage the hoses Remove the polystyrene protection from the bottom Pull up the appliance in vertical posi tion Remove the power supply cable and the drain hose from the hose holders Remove the three bolts Use the key supplied with the appliance Pull out the plastic spacers 30 www aeg com
17. he end of programme PROGRAMME KNOB Turn this knob to set a programme The related programme indicator comes on 8 www aeg com DISPLAY The display shows A e The maximum temperature of the programme B e The default spin speed of the programme No Spin 1 and Rinse Hold symbols The display symbols 2 Description Washing phase ica lt HE Rinse phases Spin phase Child lock 1 MOE You cannot open the appliance door when the symbol is on You cannot open the appliance door when the symbol flash es Wait for some minutes before you open the door You can open the door only when the symbol goes off If the programme is completed but the symbol stays on e There is water in the drum e The Rinse Hold function is on Delay start D The programme time ENGLISH 9 When the programme starts the time decreases with steps of 1 minute e The delay start When you press the delay start button the display shows the delay start time e Alarm codes If the appliance has a malfunction the display shows alarm codes Refer to Troubleshooting chapter e Err The display shows this message for some seconds if You set a function that is not applicable for the programme You change the programme while it operates The indicator of the Start Pause button flashes 2 08 When the programme is completed 1 Only available for Spi
18. he spin Spin phase is off Rinse Hold function is on 10 www aeg com TEMPERATURE BUTTON Press button fq to change the default temperature cold water ACOUSTIC SIGNALS FUNCTION You can hear the acoustic signals when e You activate the appliance e You deactivate the appliance e You press the buttons e The programme is completed e The appliance has a malfunction To deactivate activate the acoustic sig nals press button BJ and button f at the same time for 6 seconds i If you deactivate the acoustic sig nals they continue operate only when you press the buttons and when a malfunction occurs CHILD LOCK FUNCTION This function prevents children to play with the control panel e To activate the function press button and button E at the same time un til the display shows the symbol FA e To deactivate the function press but ton BG and button fl at the same time until the symbol FX goes off You can activate the function e Before you press the Start Pause but ton RM the appliance cannot start e After you press the Start Pause button all the buttons and the programme knob are deactivated PERMANENT EXTRA RINSE FUNCTION With this function you can keep the extra rinse function permanently on when you set a new programme e To activate the function press button El and button fE at the same time un til the indicator of button is
19. ilter under the water tap and put it back in the pump into the special guides Make sure that you tighten correctly the filter to prevent leakages 10 Close the drain pump door THE INLET HOSE FILTER AND THE VALVE FILTER It could be necessary to clean the filters when e The appliance does not fill with water e The appliance fills with the water for a long time The indicator of button JZ flashes and the display shows the related alarm Re fer to Troubleshooting WARNING Disconnect the mains plug from the mains socket To clean the water inlet filters Close the water tap Remove the water inlet hose from the water tap Clean the filter in the inlet hose with a stiff brush Remove the inlet hose behind the appliance Clean the filter in the valve with a stiff brush or a towel 24 www aeg com ko 0 Install again the inlet hose Make sure that the couplings are tight to pre vent leakages Open the water tap EMERGENCY DRAIN Because of a malfunction the appliance cannot drain the water If this occurs do steps 1 through 6 of To clean the drain pump If necessary clean the pump Put the drainage duct back and close the drain pump flap When you drain the water with the emer gency drain procedure you must activate again the drain system 1 Put 2 litres of water in the main wash compartment of the detergent dis
20. itioner 6 Carefully close the detergent dis penser Make sure that the flap does not cause a blockage when you close the drawer 4 To use liquid detergent turn the flap down i With the flap in the position DOWN Do not use gelatinous or thick liquid detergents Do not put more liquid deter gent than the limit showed in the flap Do not set the prewash phase Do not set the delay start func tion SETTING AND STARTING A PROGRAMME 1 2 i Turn the programme knob The rela ted programme indicator comes on The indicator of button JJ flashes with red colour The display shows the default tem perature and spin speed To change the temperature and or the spin speed press the related buttons Set the available functions The indi cator of the set function comes on or the display shows the related symbol Press button J to start the pro gramme The indicator of button is on The appliance adjust automat ically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum neces sary time After approximately 15 minutes from the start of the programme the display shows the new time value INTERRUPT A PROGRAMME 1 Press button J The indicator flash es 2 Press button l again The washing programme continues CANCEL A PROGRAMME 1 Press button ff to cancel the pro gramme and to deactivate the appli an
21. l Wash SPIN REDUCTION ECO A oured cotton with Rinses RINSE HOLD Economy normal soil Long spin STAIN TE max 7 kg EXTRA RINSE 2 PROGRAMMES TIME ANE for the Energy Label consump tion values 1 The STAIN function is not available with a temperature lower than 40 C 2 if you press the button 6 two times Extra Quick duration we recommend that you decrease the quantity of the load It is possible to load fully the appliance however the washing results are reduced 3 The wash and spin phase is soft to prevent the creases of the laundry The appliance adds some rinses 4 The default phase of the spin speed is related to cotton items Set the spin speed Make sure that it agrees with the laundry To select the DRAIN programme only set the function NO SPIN ENGLISH 13 5 Press EXTRA RINSE button to add rinses With a low spin speed the appliance performs delicate rinses and a short spin 6 Set this programme to decrease the time and the consumption of energy and water 7 Set this programme to have a good washing results and decrease the energy consumption The time of the washing programme is extended For cotton economy programmes you can set only the Extra Quick duration CONSUMPTION VALUES Programme Energy consumption Water consump KWh tion litre 2 White Cottons 95 C 2 30 66 Cottons 60 C 1 30 62 Cottons 40 C 0 80 62 Synthetics 40 C 0 53 45 Delicates 40 C 0 57 53 Wool Handw
22. n Drain programme 2 The symbols appear on the display when the related phase or function is set START PAUSE BUTTON Press button B to start or interrupt a programme DELAY START BUTTON Press button to delay the start of a programme from 30 minutes to 20 hours TIME SAVE BUTTON AI Press the button J to decrease the pro gramme duration e Press one time to set Shortened dura tion for items with daily soil e Press two times to set Extra Quick for items with almost no soil i EXTRA RINSE BUTTON Press button R to add rinsing phases to a programme Use this function for persons allergic to detergents and in areas where the water is soft Some programmes accept only one of the two functions STAIN BUTTON 0 Press button BJ to add the stain phase to a programme Use this function for laundry with hard stains to remove When you set this function put the stain remover into compartment LJ i This function increases the pro gramme duration This function is not available with a temperature lower than 40 C SPIN BUTTON MI Press this button to e Decrease the maximum speed of the spin phase when you set a programme speeds available with the set pro gramme e Deactivate the spin phase e Activate the Rinse Hold function Set this function to prevent fabric creases The appliance does not drain the water when the programme is completed The display shows only t
23. not transport your appliance with out the transit bolts you can damage internal components and cause leak ages or malfunctions e Do not install and connect a damaged appliance e Make sure to remove all packaging and transport bolts e Make sure that the mains plug is dis connected from the mains socket dur ing installation e Only a qualified person must do the electrical installation the plumbing and the installation of the appliance This to prevent the risks of structural damage or injury e Do not install or use the appliance where the temperature is less than 0 C e When you install the appliance on a carpet floor make sure that there is air circulation between the appliance and the carpet Adjust the feet to have the necessary space between the appliance and the carpet Water connection Do not connect the appliance with old hoses already used Only use new ho ses Make sure not to cause damage to the water hoses Do not connect the appliance to new pipes or pipes not used for a long time Let the water flow for some minutes then connect the inlet hose The first time you use the appliance make sure that the water hoses and the couplings do not have leakages Electrical connection ENGLISH 5 Do not replace or change the mains ca ble Contact the service centre Make sure not to cause damage to the mains plug and cable Connect the mains plug to the mains socket only at the end of
24. on e To deactivate the function press button El and button fE at the same time un til the indicator of button is off PROGRAMMES ENGLISH 11 Programme Type of load Cycle Functions Temperature max weight of load description D White and coloured Wash SPIN REDUCTION cotton with normal Rinses RINSE HOLD o soil Long spin STAIN1 ae max 7 kg EXTRA RINSE TIME SAVE 1 White and coloured Prewash SPIN REDUCTION P cotton with heavy soil Wash RINSE HOLD Ke Pre max 7 kg Rinses EXTRA RINSE i 2 Tr Long spin TIME SAVE dB White and coloured Wash STAIN See cotton with normal Rinses EXTRA RINSE Extra Silent gt soil Stop with water in 2 95 Cold max 7 kg the drum TMESAYE Synthetic or mixed Wash SPIN REDUCTION hee fabric items with nor Rinses RINSE HOLD Pee a mal level of soil Short spin STAIN aes max 3 5 kg EXTRA RINSE TIME SAVE Synthetic or mixed Prewash SPIN REDUCTION ne p fabric items with Wash RINSE HOLD eae entice Fe heavy s l Rinses EXTRA RINSE i 2 60 Cold max 3 5 kg Short spin TIME SAVE2 Synthetic fabric items Wash SPIN REDUCTION a with normal soil Rinses RINSE HOLD Easy Iron max 3 5 kg Short spin EXTRA RINSE 60 Cold TIME SAVE Delicate fabrics as Wash SPIN REDUCTION Deli acrylics viscose poly Rinses RINSE HOLD een ester items with nor Short spin STAIN mal soil EXTRA RINSE mars 5k TIME SAVE2 Van Machine washable Wash SPIN REDUCTION
25. pli ance e Keep all packaging away from children There is the risk of suffocation or injury e Keep all detergents away from children e Keep children and pets away from the appliance when the door is open e Before you close the appliance door make sure that children and pets are not into the drum e If the appliance has a child safety de vice we recommend to activate it GENERAL SAFETY e Do not use the appliance for professio nal use The appliance is only for do mestic use e Do not change the specifications of this appliance There is the risk of injury and damage to the appliance e Do not put flammable products or items that are wet with flammable products in near or on the appliance Risk of explosion or fire e Obey the safety instructions on the de tergent packaging to prevent burns to eyes mouth and throat e Make sure that you remove all metal objects from the laundry Hard and sharp material can cause damage to the appliance e Do not touch the glass of the door while a programme operates The glass can be hot only for front loading appli ances CARE AND CLEANING e Deactivate the appliance and discon nect the mains plug from the mains socket e Do not use the appliance without the filters Make sure that the installation of the filters is correct An incorrect instal lation causes water leakages INSTALLATION e The appliance is heavy be careful when you move it e Do
26. r inlet damaged hose has no damages The filters in the water in Clean the filters Refer to Care let hose is blocked and cleaning The water tap is blocked Clean the water tap or is furred with lime scale The connection of the Make sure that the connection is water inlet hose is not correct correct The water pressure is too Contact your local water authori low ty The appliance The water drain hose is Make sure that the water drain does not drain the damaged hose has no damages water The filter of the drain pump is blocked Clean the filter of the drain pump Refer to Care and clean ing The connection of the water drain hose is not correct Make sure that the connection is correct A washing programme without the drain phase is set The function Rinse amp Hold is on The appliance door is open or not closed correct ly Set the drain programme Set the drain programme Close the door correctly 26 www aeg com Problem The spin phase does not operate Possible cause The spin phase is off The filter of the drain pump is blocked Possible solution Set the spin programme Clean the filter of the drain pump Refer to Care and clean ing Balance problems with the laundry load Adjust manually the items in the tub and start the spin phase again The programme does not start The mains plug is not connected in the mains socke
27. t Put in the mains plug Blow out fuse in the household fuse box You did not press button The delay start is set Replace the fuse Press button To start immediately the pro gramme cancel the delay start The Child Lock function is activated Deactivate the Child Lock func tion There is water on the floor Leakages from the cou plings of the water ho ses Leakages from the drain pump The water drain hose is damaged Make sure that the couplings are tight Make sure that the drain pump filter is tight Make sure that the water inlet hose has no damages You cannot open the appliance door The washing programme is in operation Let the washing programme end The appliance makes an unusual noise There is water in the drum Incorrect level of the ap pliance You did not remove the packaging and or the transit bolts The load is very small Set the drain or the spin pro gramme Adjust the level of the appliance Refer to Installation Remove the packaging and or the transit bolts Refer to Instal lation Add more laundry in the drum The appliance fills with water and drain immediately The end of the drain hose is too low Make sure that the drain hose is in the correct position The washing re sults are not satis factory The detergent you used was not sufficient or cor rect Increase the deter
28. the laundry in the appliance 5 Use the correct quantity of detergent and additives 6 Set and start the correct programme for the type of laundry and soil not to put too much laundry in the drum 3 Close the door Make sure that no laundry stays between the seal and the door There is a risk of water leakage or damage to the laundry LW oO ENGLISH 15 The detergent compartment for the prewash phase the soak pro gramme and for the stain function Add the detergent for prewash soak and stain remover before the start of the programme The detergent compartment for the washing phase If you use a liquid detergent put it immediately before you start the programme Liquid additives compartment fabric conditioner starch Put the product in the compartment before you start the pro gramme MAX AIX This is the maximum level for the quantity of liquid additives Flap for powder or liquid detergent Turn it up or down in the correct position to use powder or liquid detergent Always obey the instructions that you find on the packaging of the deter gent products Check the position of the flap 1 Pull out the detergent dispenser until it stops 2 Press the lever down to remove the dispenser 3 To use powder detergent turn the flap up 16 www aeg com N He 5 Measure out the detergent and the fabric cond
29. uplings The inlet hose has a water stop device This device prevents water leaks in the hose because of its natural ageing The red sector in the window A shows this fault If this occur close the water tap and con tact the service centre to replace the hose 32 www aeg com WATER DRAINAGE There are different procedures to connect the drain hose With the plastic hose guide On the edge of a sink Make sure that the plastic guide cannot move when the appliance drains At tach the guide to the water tap or the wall To a stand pipe with vent hole Refer to the illustration Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm The end of the drain hose must always be ventilated i e the inner diameter of the drainpipe must be larger than the external diameter of the drain hose e To a sink spigot Refer to the illustration Put the drain hose in the spigot and tighten it with a clip Make sure that the drain hose makes a loop to prevent that remaining particles go in the appliance from the sink ENGLISH e Directly to a built in drain pipe in the room wall and tighten it with a clip 33 You can extend the drain hose to maximum 400 cm Contact the service centre for the other drain hose and the extension 34 www aeg com ENGLISH 35 www aeg com shop 132928260 A 50201 1 ale tele
Download Pdf Manuals
Related Search