Blue Rhino 81000 Electric Heater User Manual
Contents
1. 1 Turn Gas Control Knob to OFF 2 Wait at least 5 minutes to let gas dissipate before attempting to relight burner 3 Repeat the Lighting Steps 2 and 3 on prior page Shut Down 1 Rotate Gas Control Knob to OFF position Normally burner will make a slight popping sound when extinguished 2 Turn off gas at cylinder 3 Remove Access Panel 4 Unscrew gas line from regulator 5 Close Access Panel Note After use some discoloration of the emitter screen is normal 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Endless Summer O Operation Checklist For a safe and pleasurable heating experience perform this check before each use Before Operating am familiar with entire owner s manual and understand all precautions noted in Safety First All components are properly assembled intact and operable _ No alterations have been made All gas connections are secure and do not leak _ Wind velocity is below 10 mph Outdoor temperature is greater than 40 degrees F _ Heater is outdoors outside any enclosure _ There is adequate fresh air ventilation _ Heater is away from gasoline or other flammable liquids or vapors _ Heater is away from windows air intake openings sprinklers and other water sources Heater is at least 36 from combustible materials _ Heater is on a hard and level surface There are no signs of2. Use of other fuels will detract from heaters performance and will void your warranty Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 LA di NN Before you do anything else read and understand all precautions in Safety First A WARNINGS FOR YOUR SAFETY e Purchaser assumes all risk in the assembly and operation of this unit Failure to follow this manual s warnings and instructions can result in severe personal injury death or property damage Combustion of propane creates carbon monoxide which when used in enclosed areas can kill you Dome is extremely hot to the touch during operation Never touch the dome while the heater is operating Wait for unit to cool down approximately 45 minutes after use Do not use in an explosive atmosphere Keep heater away from areas where flammable liquids gasoline vapors or explosives are stored or used LA e oa NN 20 Ib LP Cylinder Collar Valve FOR YOUR SAFETY Beware of Spiders Spiders or small insects can get into the burner tube or other openings of your heater and spin webs or build nests These obstructions can lead to gas flow problems It is important to make frequent inspections of these areas and clean them when necessary Before operating your heater for the first time be sure to check for obstructions that may have occurred during shipment Need a cylinder or gas Tr
3. adults to the hazards of high temperatures especially to avoid burns or clothing catching fire e Young children and pets should be carefully supervised when they are in the area of heater e Do not hang clothing or other flammable materials either on or near heater e Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater e Certain materials or items when stored under heater will be subjected to radiant heat and could be seriously damaged e Do not modify heater in any manner e The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer e Inspect heater and extension hose before each use of the appliance Ifa damaged part is detected do not operate until an original equipment replacement part has been properly installed Use of unauthorized parts will void warranty and create an unsafe condition e Do not attempt to use this appliance without a functional factory supplied gas regulator in place If regulator becomes damaged use only a factory supplied replacement e During operation do not touch burner assembly The surface of heater s emitter can reach temperatures approaching 1600 F e After shutdown do not touch emitter assembly until heater has cooled approximately 45 minutes after use Notice This product should not be used with any fuel other than liquid propane
4. connections Check for leaks even if your unit was assembled e Inspect the connections and look for bubbles for you at the store e Spoon several drops or use squirt bottle of the solution onto the regulator canister connections e If NO bubbles appear the connection is safe e If bubbles appear there is a leak e Loosen and re tighten this connection e Re check for a leak e If you continue to see bubbles after several attempts disconnect propane source and contact 1 800 762 1142 Step 8 Install Access Panel e Slide top tab of Access Panel inside Shroud Cover e Lower bottom of Panel until closed and rotate Knob until lock flange rotates inside of slot on plastic ring Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 LA e oa NN Contact 1 800 762 1142 for assistance Do not return to place of purchase Step 9 Securing the Tank Mount your 20 Ib cylinder to a sturdy object such as a table or post within 3 to 4 feet of your heater when in use this will prevent movement or tipping of the cylinder during operation The clamp on the cylinder ring will attach to any round pole from 1 to 2 in diameter or a square post from 1 to 2 square It will also adapt to various other shapes up to 2 wide Determine where to locate your 20 Ib cylinder Be sure that it is within 2 what you are mounting
5. outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Endless Summer O Components Hardware Used In Picture Qty Description Step ae 4 Medium Screw 1 cy Dome Cap H 3 MediumNut 3 1 Thumb Screw 5 Dome 1 Lock up Bracket 5 Top Wire Guard Emitter Assembly 7 1 Finial 4 3 Y Bottom Wire Guard 1 4 Dome Cap Post Shroud Cover i e Housing S 1 Extension Hose 6 Access Panel Plastic Ring Base Weight Extension Hose Lock up Mount Bracket Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Endless Summer O Do not return to place of purchase Assembly Instructions General Components amp Features Familiarize yourself with all components before proceeding Refer to page 4 for all hardware components Do NOT attempt assembly unless all components are available If you believe a component is missing or damaged contact 1 800 762 1142 for assistance Additional Requirements The following items are not included but are necessary for the proper assembly of your heater Do NOT attempt to assemble without proper tools 1 7 16 Wrench 1 2 Phillips Head Screwdriver 1 Leak Detection Solution Instructions on how to make solution are included in Step 7 1 20 Ib 4 5 gallon precision filled LP Gas Grill Cylinder Note You must follow all step
6. spider or insect nests All burner passages are clear _ All air circulation passages are clear _ Children pets clothing flammable materials and items that can be damaged from radiant heat are away from the heater _ Children and adults in the area have been alerted to the high temperature hazards especially burns and clothing fires _ Children and adults in the area have been warned not to touch heater near engine during operation and until unit has cooled After Operation _ Gas control is in OFF position _ Gas tank valve is OFF Disconnect Gas line _ Heater is upright in a secure location Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 12 Troubleshooting If the problem is Burner won t light Burner won t stay lit Burner flame is low Note Heater operates at reduced efficiency below 40 F 5 C Emitter glows uneven Carbon build up Thick black smoke LA e oa NO And this condition exists Gas pressure is low Blockage in burner openings Blockage in venturi tube Blockage in gas line Control knob is not in ON position Bad thermocouple Corrosion at thermocouple Burner flame not touching thermocouple Gas pressure is low Outdoor temperature is less than 40 F and tank is less than 1 4 full Control knob fully ON Gas pressure is low Heater not level Burner tilted Base is not on a level surface Heater is level Dir
7. 1ajJ aH 100p NQ a qgejsog Model No 81000 A WARNING FOR YOUR SAFETY For Outdoor Use Only outside any enclosure Solamente Para Uso En Exteriores fuera de cualquier recinto 4 WARNING FOR YOUR SAFETY Improper installation adjustment alteration damage Read the installation operation and maintenance instructions thoroughly bef installing or servicing t RNS A equipment ME mx WAN iy hy N N VY Ki did service or maintenance VAN WAN can cause injury or property N N De LA e oa NN A WARNING FOR YOUR SAFETY If you smell gas 1 Shut off gas to appliance 2 Extinguish any open flame 3 If odor continues contact your gas supplier or local fire department A WARNING FOR YOUR SAFETY Gas leaks may cause a fire or explosion which can cause serious bodily injury or death or damage to property You must follow all leak checking procedures as outlined in step 7 before operating this unit Never use an open flame to check for leaks A WARNING FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance A WARNING California Proposition 65 Chemicals Known To The State Of California To Cause Cancer Birth Defects Or Other Reproductive Harm Are Created By The Combustion Of Propane Contact 1 800 762 1142 for assistance Do not return to place of purchase Table o
8. TIGHTEN ONLY DO NOT USE ANY HAND TOOLS TO MAKE THIS CONNECTION BE CAREFUL NOT TO CROSS THREADS WHEN SCREWING IN FITTING Note if heater uses center clamp hose can be routed through opening in base and table e Set heater on base making sure that flexible gas line is routed through small slot in base e Attach gas line to cylinder by turning black plastic knob counter clockwise into cylinder valve until tight Note Be careful not to kink flexible gas line e When using the gas extension hose always locate the hose out of pathways where people may trip over it or in areas where the hose may be subject to accidental damage To connect 14 1 oz or 16 4 oz cylinder Note Some 1 lb cylinders may form frost when near empty e Line up threads on canister with those on regulator insert and rotate canister clockwise until they fit snugly together HAND TIGHTEN ONLY BE CAREFUL NOT TO CROSS THREADS WHEN SCREWING IN CANISTER Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Endless Summer O Step neck Tor Leaks ion Step 7 Check for Leaks Caution To check for leaks Your Endless Summer Portable Heater e Make 1 2 oz of leak solution by mixing one part liquid dishwashing has been checked at all factory connections for leaks Recheck all soap and 3 parts water connections as movement in shipping can loosen
9. codes In absence of local codes use the National Fuel and Gas Code ANSI Z223 1 NFPA 54 Storage and Handling of Liquefied Petroleum Gases ANSI NFPA 58 or CSA B149 1 Natural Gas and Propane Installation Code Save these instructions for future reference lf you are assembling this unit for someone else give this manual to him or her to save for future reference Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Safety First Read and become familiar with this entire manual especially the following precautions If you are unsure of anything in these instructions or the operation of your heater STOP and contact 1 800 762 1142 for assistance Caution This appliance is for outdoor use only outside any enclosure Always make sure there is fresh air ventilation e Always maintain at least 36 clearance from combustible materials e Always place heater on a hard and level surface e Do not use if the wind velocity is greater than 10 miles per hour e Heater operates at reduced efficiency below 40 F 5 C e Keep sprinklers and other water sources away from burner and controls e When using the gas extension hose always locate the hose out of pathways where people may trip over it or in areas where the hose may be subject to accidental damage e Always use extreme caution when near heater Alert both children and
10. dless Summer O Warranty Warranty Period Heater s warranty extends for 2 years from date of purchase by original purchaser Warranty Terms Manufactured by Blue Rhino Global Sourcing 104 Cambridge Plaza Drive Winston Salem NC 27104 1 800 762 1142 Manufacturer will cover All parts found to be defective due to materials or workmanship for 2 years from the date of original purchase Proof of purchase is required before warranty performance will be rendered Sales receipt and validation of product registration are valid forms of proof of purchase Manufacturer will repair or replace parts returned prepaid freight in the U S A at its sole discretion There are no other express or implied warranties Warranty Exclusion Manufacturer will NOT cover Assembly or start up Normal adjustment to burner Cleaning and or general maintenance Shipping damage Any misuse which will be determined at the sole discretion of manufacturer Damage or repairs due to service by an unauthorized agency or the use of unauthorized parts Improper assembly such as no regulator improper hook up etc Damage or repairs related to spider or insect nesting Damage due to weather conditions Warranty Procedures For service or replacement parts please call 1 800 762 1142 for return authorization and further instructions All returns must be sent via prepaid freight Legal Rights No one else is authorized to make any warranties on behalf of manufacture
11. e blockage include e Gas odor with extreme yellow tipping of flame e Heater does NOT reach the desired temperature e Heater glow is excessively uneven e Heater makes popping noises Spiders and insects can nest in burner or orifices This dangerous condition can damage heater and render it unsafe for use Clean burner holes by using a heavy duty pipe cleaner Compressed air may help clear away smaller particles Carbon deposits may create a fire hazard Clean dome and emitter with warm soapy water if any carbon deposits develop Note In a salt air environment such as near an ocean corrosion occurs more quickly than normal Frequently check for corroded areas and repair them promptly TIP Use high quality automobile wax to help maintain the appearance of your heater Apply to exterior surfaces from the pole down Do not apply to emitter screen dome or wire guard Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Endless Summer O Do not return to place of purchase Storage FOR YOUR SAFETY Never attempt to refill disposable Between uses canister Refilling may cause Turn Control Knob OFF explosion To discard contact Disconnect LP source local refuse hauler or recycle Store heater upright in an area sheltered from direct contact with center inclement weather such as rain sleet hail snow dust and debris Do not puncture or incin
12. erate If desired cover heater to protect exterior surfaces Note Wait until heater is cool before covering During periods of extended inactivity or when transporting Turn Control Knob OFF Disconnect LP source and move to a secure well ventilated location outdoors Store heater upright in an area sheltered from direct contact with inclement weather such as rain sleet hail snow dust and debris If desired cover heater to protect exterior surfaces Note Wait until heater is cool before covering Never leave LP cannister exposed to direct sunlight or excessive heat Service To learn how to service and procure parts for worn out defective or damaged components contact 1 800 762 1142 for assistance or e mail CustomerService BlueRhino com Please supply model number and serial ID number for best service support These numbers can be found on the heater s rating plate located on the housing Caution The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer Use only original equipment replacement parts Use of unauthorized parts or modification of parts will void warranty and create an unsafe condition Caution Always allow heater to cool before attempting service 15 Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase En
13. f Contents Daley PUGH RE E N tee EE E EE HER et end ee ag ewes 2 Assembly Instructions Hardware amp Component Listing 0 0 ec eee 4 General Components amp Features 0 0 0 SE SE ee es es ees 5 Additional Requirements 0 0000 cc ee eee 5 Step 1 Attach Emitter Screen EE SS SE SE se es es es ee 5 Step 2 Attach Top Wire Guard EES SE SE SE Se Ee es es ee 6 Step 3 Attach Dome to Emitter ss SE SE SE se cee eee 6 Step 4 Attach Dome Cap SEE ES SE ee 6 Step 5 Center Lockup 0 0 Es SE se ee ee 7 Step 6 Gas Hook up SS SE SE SS SS ee eee T Step 7 Check for Leaks 0 0 EE SE SE ee es 8 Step 8 Install Access Panel EE EE SS SE EE Se ee 8 Step 9 Securing the tank SE SS SE SS SE SE eee 9 Operation Before Turning Gas Supply ON SS SS ESE SS ee 10 Before Lighting ESE SE SE cee eee eee es ee 10 WIGHUAG EE EE EE EG EE ER EE eee OE OE E 10 Re LIGMUNG RE ET OE OE TE OR EN HOE EE OR ES EG 11 eg Uie ei ARE OO RE EA N FR N OE EE SPEEL N 11 Operation Checklist ESE SS ESE SS ee ee eee 12 Troubleshooting 0 0 EE SE SE SE ee tee eet eens 13 Maintenance N a EA EE EE EN ER 14 Site ie RE EE N ee RE OP ER N EE N EE 15 SR die nate ese N E ye ne A a EO EE OE N ee 15 VRESE o ie boe Sie ae DERE RE ag ew a Ba DA Har EE EN Ee DR WE S 16 oreo es sin AAR EE OE EE EE OE ER EE EE 17 The use and installation of this product must conform to local
14. ide a building garage or any other enclosed area Make sure surrounding areas are free of combustible materials gasoline and other flammable vapors or liquids Ensure that there is no obstruction to air ventilation Be sure all gas connections are tight and there are no leaks Be sure the access panel is clear of debris property damage Be sure any component removed during assembly or servicing is replaced and fastened prior to starting e If at any time you are unable to light burner and smell gas Before Lighting wait 5 minutes to allow gas Heater should be thoroughly inspected before each use and by a to dissipate before qualified service person at least annually attempting to light heater If relighting a hot heater always wait at least 5 minutes for gas to dissipate e Do NOT touch emitter or dome or move heater for at Lighting least 45 minutes after use _ Turn Gas Control Knob to OFF position 2 Push in Control Knob and rotate to ON position This will light burner If necessary keep depressing and rotating Knob until burner lights 3 Once burner is lit hold Control Knob in for at least 30 seconds and release 4 If burner does not stay lit wait 5 minutes and repeat steps 2 and 3 5 Once burner is lit rotate Knob to desired heating level 6 Replace Access Panel If you experience any ignition problem turn off the heater and gas supply and consult Troubleshooting on page 13 Owner s
15. it to Place the bracket halves around the object and insert the 2 bolts through the open holes in one bracket and into the matching threaded holes in the second bracket Position bracket within 6 of the middle of the cylinder Finger tighten bolts Slide the 20 Ib cylinder into the curved portion of the bracket making sure strapping ends are not between cylinder and bracket Enclose cylinder in strap and securely tighten strap in buckle Using a 7 16 wrench tighten the 2 bolts until they are secure DO NOT OVER TIGHTEN In some cases you may wish to secure your cylinder to a larger object or a wall It is possible to mount the bracket attached to the straps to these surfaces by drilling matching holes and using screws and nuts or lag screws not provided to secure your cylinder Note Once you have read safety first and successfully completed Steps 1 9 you are ready to begin operating your heater Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Endless Summer O Operation SPEA A WARNINGS Before Turning Gas Supply ON FOR YOUR SAFETY e Do NOT attempt to operate heater until you have read and understand all precautions in section 1 Safety First Failure to do so can result in serious personal injury death or Your heater was designed and approved for OUTDOOR USE ONLY DO NOT use it ins
16. manual and assembly instructions 81000 portable outdoor heater 3 3 03 LA e oa NN A WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this heater Holding in the contrrol know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition 11 Owner s manual and assembly instructions 81000 portable outdoor heater Contact 1 800 762 1142 for assistance Do not return to place of purchase Caution Avoid inhaling fumes emitted from the heater s first use Smoke and odor from the burning of oils used in manufacturing will appear Both smoke and odor will dissipate after approximately 30 minutes The heater should NOT produce thick black smoke Note The burner may be noisy when initially turned on To eliminate excessive noise from the burner turn the Control Knob to the LOW position Then turn the knob to the level of heat desired When heater is ON Emitter screen will become bright red due to intense heat The color is more visible at night Burner will display tongues of blue flame These flames should not be yellow or produce thick black smoke indicating an obstruction of airflow through the burners If yellow flame is detected turn off heater and gas supply and consult Troubleshooting on page 13 Re lighting Note For your safety Control Knob cannot be turned ON without first depressing Control Knob in OFF position and then rotating to ON
17. ne Gas LP Cylinder Size Nominal 20 Ib 5 Gallon OR 14 1 oz 400 grams 16 4 oz 465 grams Inlet gas supply pressure Maximum 150 PSI Minimum 5 PSI Manifold Pressure 11 00 in W C Supply Pressure 0 41 psig 11 00 in W C Engine IPP E8 Safety Features 100 Burner shut off Tilt Switch Manufacturer Blue Rhino Global Sourcing Made In China Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Owner s manual and assembly instructions 81000 portable outdoor heater LA e oa NN 3 3 03 18 o com uerhin f y 42 A ww bl y i WEN E MK af e Rhino Corporation NASDAO RINO ti Global Sourcing e Winston Salem NC 27104 USA i no F Blu if hir i of yA eR l Ve me ad PT
18. r THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY EXPRESS OR IMPLIED ORAL OR WRITTEN INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE BLUE RHINO GLOBAL SOURCING SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY DEFECTIVE PRODUCT INCLUDING BUT NOT LIMITED TO LOST REVENUE OR PROFITS BUSINESS INTERRUPTION OR ANY LEGAL THEORY UPON WHICH ANY CLAIM MAY BE BASED PURCHASER ASSUMES ALL RISK IN THE ASSEMBLY AND OPERATION OF THIS UNIT FAILURE TO FOLLOW THIS MANUAL S WARNINGS AND INSTRUCTIONS CAN RESULT IN SEVERE PERSONAL INJURY DEATH OR PROPERTY DAMAGE Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation relevant to incidental or consequential damages This warranty gives you specific legal rights You may also have other legal rights which vary from state to state Since product improvement is an ongoing process at the manufacturer we reserve the right to change this products specifications or design without notice Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 16 LA e oa NN Contact 1 800 762 1142 for assistance Do not return to place of purchase Specifications Certifications CSA International Requirement 5 90 Canadian National Standard CAN1 2 23 M82 Rating Maximum 14 000 BTU hr input Heat Range Up to 10 foot diameter Fuel Liquid Propa
19. rm a leak test on gas connections whenever a cylinder is connected see Steps 6 amp 7 Never use a flame to test for leaks Do not smoke while performing a leak test Caution It is essential to keep the heater s valve compartment burners and circulating air passages clean e Spiders and insects can create a dangerous condition that may damage heater or make it unsafe Keep burner area clean of all spiders webs or insects e Inspect heater before each use e Have heater inspected annually and repairs should be made by a qualified service person e Check heater immediately if any of the following conditions exist e The smell of gas in conjunction with extreme yellow tipping of burner flames e Heater does not reach proper temperature Note At temperatures less than 40 F 5 C heat output will be restricted e Heater s glow is excessively uneven e Burner makes popping noises during use Note A slight pop is normal when burner is extinguished e Carbon deposits may create a fire hazard Keep dome and emitter clean at all times e Do not clean heater with combustible or corrosive cleaners Use warm soapy water e Do not paint any part of this product Note When using a 20 lb Cylinder it is necessary to use the special hose adaptor provided for this connection This adapter is supplied with a type POL connecter at the cylinder connection end Owner s manual and assembly instructions 81000 portable
20. s to properly assemble heater Step 1 Attach Emitter Screen e Line up 4 holes on bottom of Emitter Screen with corresponding holes in Emitter Bottom and insert 4 Medium Screws in holes until tight Owner s manual and assembly instructions 81000 portable outdoor heater 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Step 2 Attach Top Wire Guard e Line up 4 prongs on Wire Guard Bottom with 4 holes on Emitter Bottom and Insert Note It may be necessary to adjust the prongs slightly to line them up with the holes Step 3 Aftach Dome to Emitter e Line up three studs in Emitter with holes in Dome Slide Dome carefully over studs clamping Top Wire Guard securely in place Note It may be necessary to adjust prongs of the Top Wire Guard slightly to provide a secure fit e Install 3 Nuts on studs and tighten with 7 16 wrench Do not over tighten Step 4 Attach Dome Cap e Lay Dome Cap on Dome covering 3 Nuts and line up center holes e Insert threaded end of Finial through Cap and screw into center of Dome until secure Owner s manual and assembly instructions 81000 portable outdoor heater LA di NN 3 3 03 LA e oa NN Notice Do not use tools to tighten the thumbscrew Hand tighten only Do not over tighten to prevent possible damage to table surface Caution Before you attempt to use a propane cylinder understand all c
21. t or film on reflector and emitter Blockage in burner Owner s manual and assembly instructions 81000 portable outdoor heater Contact 1 800 762 1142 for assistance Do not return to place of purchase Then do this Replace cylinder or canister Clear blockage Clean venturi Check gas line for blockage Turn control knob to ON Replace thermocouple Clean contact Contact certified technican Turn Control Knob OFF and replace cylinder or canister Use a full cylinder or canister Check burner and all openings for blockage Replace cylinder or canister Level heater Straighten burner Place heater on a level surface Clean burner Clean reflector and emitter Remove blockage and clean burner inside and outside 3 3 03 Contact 1 800 762 1142 for assistance Do not return to place of purchase Endless Summer O Maintenance To enjoy years of outstanding performance from your heater make sure you perform the following maintenance activities on a regular basis e Keep exterior surfaces clean e Use warm soapy water for cleaning Never use flammable or corrosive cleaning agents e While cleaning your unit be sure to keep the area around the burner and pilot assembly dry at all times Do not submerge the control valve assembly If the gas control is submerged in water do NOT use it It must be replaced Air flow must be unobstructed Keep controls burner and circulating air passageways clean Signs of possibl
22. y Blue Rhino cylinder exchange service It s easy fast safe and available at tens of thousands of conveniently located retail outlets nationwide You can purchase a new full cylinder or exchange your empty for a precision filled one For your nearest Blue Rhino retailer visit www bluerhino com Contact 1 800 762 1142 for assistance Do not return to place of purchase Caution Liquid propane LP gas is flammable and hazardous if handled improperly Become aware of the characteristics before using any LP product e LP Characteristics Flammable explosive heavier than air settles in low areas e In its natural state propane has no odor For your safety an odorant is added that smells like rotten cabbage e Contact with liquid LP can cause freeze burns to skin e This heater is shipped from the factory for LP gas use only e Use only Department of Transportation DOT approved 20 Ib LP gas cylinders Same as commonly used on gas grills with Acme Type 1 QCC safety valves These valves can be quickly identified by their external and internal threads e Never use a cylinder with a damaged body valve collar or foot ring e When using a 20 Ib LP gas cylinder the cylinder supply system must be arranged for vapor withdrawl e When using a 20 Ib LP gas cylinder the cylinder used must include a collar to protect the cylinder valve e When heater is not in use turn Control Valve OFF e Always perfo
23. ylinder and propane related precautions in Section 1 Safety First Contact 1 800 762 1142 for assistance Do not return to place of purchase Step 5 Center Lockup e Slide the threaded portion of the large thumbscrew through the slot in the center of the bracket mounted to the base e Thread the bottom bracket on to the thumbscrew with the round flat rubber pads facing up e To mount the heater to a hole in your table tilt the bottom bracket thumbscrew assembly until it fits through the hole Straighten the thumbscrew and pull it up until the rubber pads contact the underside of the table Hand tighten only Note If the hole in the surface you are mounting your heater to is less than 1 1 2 in diameter it will be necessary to center your heater over the hole and slide the thumbscrew through the slot in the bracket and the hole in the table Attach the bottom bracket from underneath and tighten from the top with the thumbscrew Step 6 Gas Hook up Note For best results use heater with a 20 Ib cylinder The pressure regulator and hose assembly supplied with the appliance must be used and replacements must be those specified by the manufacturer To connect 20 Ib Cylinder e Slip end of flexible gas line with brass fitting through center hole of Base and up to threaded portion of regulator e Line up threads on fitting with those on regulator and rotate clockwise until snug HAND
Download Pdf Manuals
Related Search