Bissell 7950 Carpet Cleaner User Manual
Contents
1. ways with BISSELL Tough Stain PreCleaner Then deep clean with the SmartMix Dial set on High Traffic Carpet Cleaning Plug into a proper outlet and turn the Power and the Smartlemp Switches ON 1 Wait 2 minutes for the heater to warm up to maximize cleaning While pressing the Trigger make one slow forward wet pass and another one back Let the Smartlemp heated formula and DirtLifter PowerBrush do the work for you Caution Do not overwet Note Take care not to run over loose objects or edges of area rugs Stalling brush may result in premature belt failure Release the Trigger and make one slow forward and back pass over the same area to remove any residual dirty water A ATTENTION BERBER CARPET OWNERS Some Berber Carpets have a tendency to fuzz with wear Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition Please see Stain Removal instructions on page 12 Repeat cleaning passes until solution being pulled up appears clean For the most thorough clean use slow forward and backward passes Continue passes without pressing the trigger until you can t see any more water being pulled up Note Both the SmartMix Tank and the clean water tank must have liquid in them for the machine to spray If one tank is empty the machine will not apply either cleaning solution or water only When filling bottle or toring unit set storing SE e P2. Both switches must be ON 1 to turned ON 1 activate the SmartTemp Ready Light Reduced spray or no spray Possible Cause Remedies Bladder may be empty Refill Bladder with hot tap water SmartMix Tank may be empty Fill with BISSELL deep cleaning formula for cleaning or water if rinsing or using the Scotchgard protector applicator The filter may be clogged Clean out Flow Indicator Filter page 17 Tanks may not be seated properly Turn power OFF remove amp reseat tanks Inspect for presence of seals Pump may have lost prime Turn power OFF after 1 minute turn ON and depress Trigger The Pump Belt may be broken Turn the machine OFF and unplug from the outlet To check if a Pump Belt has broken you will need a flat head screwdriver Insert the blade end into the lower slot of the Belt Access door to release the lower snap If necessary insert the blade end into the upper slot to release the upper snap Examine the belt for breakage You should be able to see the Pump Belt looped around the motor shaft If Lift Here lt it is broken or missing please refer to Replacement Parts on page 23 before calling Consumer Services Complete nsert installation instructions will Screwdriver Bade Here accompany the replacement belt Troubleshooting Continued DirtLifter PowerBrush does not turn Possible Causes The Brush Belt or Pump Belt is off or broken Carpet Protector is not spr
3. CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW BISSEll INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE 2004 BISSELL Homecare Inc All rights reserved Imported by BISSELL Canada Corporation NIAGARA FALLS ONTARIO L2E 6S5 Part Number 310 5835 Visit our website at www bissell com Scotchgard is a registered trademark of 3M
4. floor see illustration Remove Tank In Tank and SmartMix Tanks Set them aside see illustration Remove Belt Access Door located near the Floor Cleaning Tools switch by inserting a flat head screwdriver into the slot nearest to the handle and gently prying the access door off see illustration Turn the machine onto its side so the belt access area is facing upward see illustration On the bottom of the machine near the belt access area is a red retainer plate that holds the black brush arm and brush in place Using a Phillips head screwdriver remove the screw that holds the red retainer plate in place Set red retainer plate and Phillips head screw aside See illustration Remove the black brush arm that holds the brush in place Set the black brush arm aside see illustration Remove the toothed brush belt from the brush then from the red pump pulley Set the toothed brush belt and brush aside Locate and remove broken pump belt OOO OO 66 80 To Install the Replacement Pump Belt OO OO OOQ O With the unit still on its side loop one end of the replacement pump belt around the red pump pulley and then the other end around the silver motor shaft see illustration Do not twist the replacement pump belt Re install the toothed brush belt first onto the red pump pulley and then onto the toothed end of the brush see illustration Re Install the brush into the base of unit Place the black
5. scotchgard protector Applicator Optional The Scotchgard protector applicator with formula included can be used to help retain the carpet cleanliness you achieve with your ProHeat machine For best results the post cleaning treatment should be applied while the carpet is still wet or damp It is recommended that the Scotchgard protector iS applied every 12 months in all carpeted areas and after every deep Cleaning for high traffic areas such as entryways and stairs Immediately after cleaning and rinsing your carpets empty the Tank in Tank and refill the Bladder with clean hot tap water See page 7 amp 8 for instructions Set the ReadyTools Dial to Tools Pretreat Flush water through the hose to eliminate cleaning solution from the tube by spraying water through the hose without attachments into a sink for 15 30 seconds Attach cartridge to the applicator tool following instructions on cartridge Turn the SmartMix Dial to the Water Rinse Carpet Protectant Setting Place the Scotchgard protector applicator onto the end of the Flex Hose The water from the Tank in Tank will automatically mix with the concentrated protectant formula contained in the cartridge Before applying Scotchgard protector test a small hidden area for colorfastness Examine area when dry If color is affected do not use For upholstery look for manufacturer s cleanability code tag Use on fabrics coded W or WS If coded S o
6. through 9 on page 8 Fill bladder only with clean Refer to the Maintenance section pg 17 for the final cleanup The Flow Indicator The Flow Indicator is located on the machine base It spins when the trigger is pressed to indicate that the machine is applying cleaning solution to the floor It will stop spinning to indicate that the SmartMix Tank or bladder needs to be refilled or when the trigger is released Flow Indicator does not spin when the Ready Tools Dial is set to Tool setting A special red float device in the tank will cause the cleaner to stop removing solution from the j carpet and the Ready Tools Dial motor sound will Thorough vacuuming rise in pitch to let you know the l isan i This provides above floor cleaning with the flip of a switch othe Water ays prevent cat Just choose the cleaning tool or protector applicator attach S fogd o to the flex hose and ProHeat is ready to clean upholstery or aes stairs or apply extra protection against dirt and tough stains when using the Scotchgard protector applicator Set the dial to Floor Cleaning when cleaning carpets or bare floors or set it to Tools PreTreat when using the flex hose attachments or for pre treating floors or when applying the Scotchgard protector applicator SmartTemp heats the cleaning solution for carpet and bare floor application only It does not heat solution sprayed through the accessory tools ReadyTools Dial lt
7. 7 20 How to Clean Upholstery and Small Areas Manufacturer s tag N WARNING To reduce the risk of injury be extra careful when cleaning stairs Make sure machine is secure and level Tip Deep cleaning carpeting and upholstery with BISSELL Multi Allergen Removal Formula regularly can reduce dust mite waste and allergens in your home Cleaning Bare Floors The Bare Floor Tool available with select models only provides effective cleaning for linoleum vinyl and tile floors Caution Do not use on hardwood floors Use BISSELL Floor Cleansing Formula Vacuum or sweep thoroughly to pick up loose debris and pet hair Remove easily moved furniture from the room chairs tables etc Plan your cleaning route to leave an exit path Plan activities to allow 30 minutes for the floor to dry completely G66060 Attach the Bare Floor Tool Step on the Handle Release to lay the machine handle down Remove the Tank in Tank from the machine base Lift the machine base to expose the underside of the Floor Nozzle Window Attach Bare Floor Tool to Floor Nozzle Window with long tab to the right side ReadyTools side of the nozzle First attach left side short Tab catching tab over nozzle edge Gently bend long tab right side outward to easily snap over edge of clear nozzle on left OO O O06 Machine Preparation Set up machine following instructions in the Features section pages 6 9 B
8. SELF PROPELLED 7950 SERIES Thanks for buying a BISSELL ProHeat Self Propelled We re glad you purchased a BISSELL ProHeat Self Propelled heated formula deep cleaner Everything we know about floor care went into the design and construction of this complete high tech home cleaning system Your ProHeat Self Propelled is well made and we back it with a limited 2 year warranty We also stand behind it with a knowledgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your ProHeat Self Propelled deep cleaner Thanks again from all of us at BISSELL Amor 4 Arb Mark J Bissell President and Chief Executive Officer IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following Read all instructions before using your ProHeat A WARNING To reduce the risk of fire electric shock or injury m Do not immerse m Use only on surfaces moistened by cleaning process m Always connect to a properly grounded outlet m See Grounding Instructions m Unplug from outlet when not in use and before conducting maintenance or troubleshooting Do not leave machine when it is plugged in Do not service machi
9. aying Possible Causes Bottle not connected properly to the tool Solution clogging the Spray trigger Applicator tool spray is blocked SmartMix not set on water rinse carpet protector setting ReadyTool dial not set on tool setting Cleaner not picking up solution Possible Cause Ready Tools dial may be at the wrong setting for the cleaning job Nozzle Window may not be properly attached Tank in Tank lid is not properly installed Tank in Tank is not properly seated Poor tool position Hand held attachments only Tank in Tank has picked up maximum dirty water Remedies Turn the machine OFF and unplug from the outlet To check if a Pump Belt has broken you will need a flat head screwdriver Insert the blade end into the lower slot of the Belt Access door to release the lower snap If necessary insert the blade end into the upper slot to release the upper snap Examine the belt for breakage If broken refer to pages 18 19 Remedies Follow instructions on cartridge assuring proper fit Soak applicator tool only in hot water Spray without the cartridge attached to purge any residual Solution left in the tool Soak applicator tool only in hot water Spray without the cartridge attached to purge any residual Solution left in the tool Set to proper setting Set to tool setting Remedies Set ReadyTools dial to either Tools or PreTreat or Floor Cleaning Pres
10. belt door is securely assembled in the location provided m Use only manufacturer s recommended attachments m Use only cleaning products formulated by BISSELL for use in this appliance m Keep openings free of dust lint hair etc a Do not point attachment nozzle at people or animals m Keep appliance on a level surface Turn off all controls before unplugging a Unplug before attaching the TurboBrush a Be extra careful when cleaning stairs Close attention is necessary when used by or near children SAVE THESE INSTRUCTIONS THIS MODEL IS FOR HOUSEHOLD USE ONLY Commercial use of this unit voids the manufacturer s warranty GROUNDING INSTRUCTIONS This appliance must be connected to a grounded wiring system If it should malfunction or break down grounding provides a safe path of least resistance for electrical current reducing the risk of electrical shock The cord for this appliance has an equipment grounding conductor and a grounding plug It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances Grounded Outlets Grounding Pin A WARNING Improper connection of the equipment grounding conductor can result in a risk of electrical shock Check with a qualified electrician or service per son if you aren t sure if the outlet is prop erly grounded DO NOT MODIFY THE PLUG If it will not fit the outlet have a proper outlet
11. brush arm onto the brush and slide black brush arm into base of unit The black brush arm and brush should slide easily into original position see illustration Re install the red retainer plate and Phillips head screw see illustration Using your finger gently spin the replacement pump belt on the silver motor shaft If assembled correctly the replacement pump belt should rotate freely around the silver motor shaft and drive pulley without obstruction The brush should also rotate freely when the silver motor shaft is turned Turn the machine right side up and replace the Tank In Tank SmartMix Tank and belt access door see illustration Assembly is now complete If you have any questions or are having trouble installing your replacement pump belt please call BISSELL Consumer Services at 1 800 263 2535 ZAWARNING To reduce the risk of Troubleshooting fire electric shock or injury unplug from outlet before servicing Powerdrive does not seem to be engaged Possible Causes Remedies The Powerdrive is in the OFF position Turn the Powerdrive Knob to the ON Position Handle not fully engaged with Powerdrive position Push handle in as far as it will go to feel the most impact SmartTemp Ready Light does not illuminate Possible Causes Remedies The SmartTemp Switch is not turned ON 1 Turn on the SmartTemp Switch The machine Power Switch is not
12. d Assembly 8 015 4439 Tank Lid Assembly 9 015 9041 Tank Bottom Assembly 10 210 1785 SmartMix Bottle Includes Cap Assembly 11 210 1795 SmartMix Cap Assembly 12 555 6503 Flow Indicator Assembly 13 210 4052 Window Gasket 14 214 9865 Floor Nozzle Window and Gasket 15 215 0628 Replacement Pump Belt With Instructions 16 015 0621 Replacement Brush Belt With Instructions 17 213 3501 Lint Screen 18 215 2152 Applicator Tool Not all parts are included with every model Keep plenty of genuine BISSELL cleaning formulas and Scotchgard protector cartridges on hand 19 464C Scotchgard protector Cartridge 236 mL 20 3 7100 715C Fiber Cleansing Formula 1 42L 3 78L 21 720C 725C Multi Allergen Removal Formula 1 42L 3 78L 22 740C Natural Orange Extract Formula 1 42L 23 480E Floor Cleansing Formula 946 mL If you need additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by e mail telephone or regular mail as described below Limited Two Year Warranty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Canada Corporation will repair or replace with new or remanufac tured components or products at BISSELL s option free of charge from the date of purchase by the original purchaser for two years any defective or malfunctioning part See information below on If your BISSELL product should
13. e oat SmartMix When the cleaning job is complete refer to the Dial to Maintenance section for machine cleanup and storage O WATERING instructions on pages 17 19 PROTECTOR Cleaning Formula Keep plenty of genuine BISSELL Deep Cleaning Formula and Scotchgard protector cartridges on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Note Always use genuine BISSELL deep cleaning formulas to reduce the risk of fire and electric shock due to internal component damage 9826060 086 Keep plenty of genuine BISSELL deep cleaning formula and Scotchgard protector cartridges on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine and void the warranty 1 42L 3 78L 1 42 3 78l 1 42L BISSELI BISSELL BISSELL Natural Orange Fiber Cleansing Multi Allergen Extract Formula Formula with Removal with Scotchgard scotchgard Formulawith Protector Protector scotchgard item 740C item 710C Protector 715C item 720C 1 1 725C Stain Removal Do Not Delay Failure to attend to an accident soon after it occurs may cause it to set and become permanent Before treating any stain follow these pre treatment steps OO O Blot up liquids with an absorbent cloth or paper towels White materials ar
14. e recommended because certain dyes may bleed and make the stain worse Gently scrape up semi solids with a spoon or spatula Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery lf the area has dried remove the remaining semi solids and residue with a sweeper or vacuum Be sure to pre test any spot removal solutions or chemicals on an inconspicuous area first This is extremely important different dyes and materials could be damaged or discolored by a cleaning solution If such a change should occur try a different solution or call a professional If cleaning on Berber Carpet gently run your machine over a hidden area If no fuzzing occurs continue cleaning in soiled area Use one of the following methods to Preclean the stain Q Using BISSELL Tough Stain Precleaner generously spray the area with the formula Gently work the solution with a clean cloth or towel into the area using light strokes from the edges of the stain to the center When you reach the center of the stain with your cloth gently pinch it in an upward motion Make sure to turn and change your cloth frequently and do not rub the stain You may repeat this process several times or Use your BISSELL deep cleaner as a Precleaner With one of the tools attached to hose set the Ready Tools Dial to Pretreat and the SmartMix Dial to the High Traffic setting Spray the area with solution and allow the Dee
15. e sure to thoroughly rinse out any remaining Fiber Cleansing Formula from the SmartMix Tank to prevent slippery linoleum vinyl and tile floors Use BISSELL Floor Cleansing Formula in the SmartMix Tank Check ReadyTools Dial it should be set on Floor Cleaning Choose the SmartMix setting to match the cleaning job Plug into a proper outlet and turn Power Switch ON 1 Turn Smartlemp Switch ON 1 The SmartTemp Ready Light illuminates and the ProHeat is ready to clean OOO Cleanin When filling bottle or storing unit set SmartMix s Dialto WATER RINSE 6 CARPET oe PROTECTOR Bare Floor Cleaning Technique Slowly move the machine nozzle with Bare Floor Tool forward and back over soiled surface one time while pressing the Trigger Caution Do not over wet N WARNING To reduce the risk of fire ot gel i electric shock or injury Repeat the motion without pressing the Trigger using the Bare unplug from outlet before servicing Floor Tool to squeegee and suction up the dirty water Repeat steps 1 and 2 backing along the exit path Tip SmartMix Bottle may be stored When the cleaning job is complete refer to the with concentrate Maintenance Storage section on pages 17 20 ready for your next cleaning job Make sure dial is turned to the Water Rinse Carpet Protector Setting when storing Allow about 30 minutes for the floor to dry completely To remove Bare Fl
16. ectant through the applicator to prevent the pump from temporarily losing its prime Normal automatically provides the best mix of water and concentrate for most cleaning jobs High Traffic automatically mixes the right amount of water and concentrate to dissolve tough grime and heavy soil Note Residual cleaning materials left in carpet from other products may cause excessive foaming when picked up If foam is overflowing tank move SmartMix Dial to Water Only position until the condition stops Note Both the SmartMix Tank and the clean water tank must have liquid in them for the machine to spray If one tank is empty the machine will temporarily lose its prime and not apply either cleaning solution or water only DirtLifter PowerBrush The powered brush roll at the floor nozzle is designed to enhance cleaning performance The bristle pattern lifts out the deep down dirt while gently grooming carpet fibers The floating suspension self adjusts to all carpet heights and protects your carpet if you leave the power switch ON I When the machine handle is in the fully upright position Carpet Saver automatically raises the brush off the carpet Deep Cleaning stairs and high traffic areas on a regular basis and using the Scotchgard protector can prolong carpet life N WARNING To reduce the risk of fire use only BISSELL Deep Cleaning Formula for full size machines in your ProHeat Use of cleaning fo
17. installed by a qualified electrician This appliance is designed for use on a nominal 120 volt circuit and has a grounding attachment plug that looks like the plug in the drawing above Make cer tain that the appliance is connected to an outlet having the same configuration as the plug No plug adapter should be used with this appliance Keep plenty of genuine BISSELL Deep Cleaning Formula and Scotchgard protector cartridges on hand so you can clean and protect whenever it fits your schedule Always use genuine BISSELL deep cleaning formulas Non BISSELL cleaning solutions may harm the machine and void the warranty Trigger Power Switch smartlemp Switch Upper Handle Tool Caddy Power Cord Scotchgard Quick Release Applicator Tool Storage Crevice Tool Storage If included Tough Stain Brush Storage oe sie g wW JE Ni Handle Release Carry Handle SmartTemp Ready Light Accessories All items may not be included with your model More tools are available To order replacement parts or tools please refer to page 23 Flow Indicator Filter Inside ReadyTools 4 Ms Did jane I OOl Tough Stain Brush PreTreat Wand SmartMix Dial AS he My DirtLifter WW SmartMix models only Available on select Tan models only Bare Floor Attachment Spraying Crevice Tool Available on select models only Available on
18. lide Upper Handle onto Lower Handle Insert 2 screws into lower holes while gently pushing down on Upper Handle See drawing for exact location Tighten screws completely Position Tool Caddy on back of unit Insert 4 screws until snug Snap tools into storage on the Tool Caddy as shown in figure 4 ProHeat assembly is now complete special Features of your BISSELL ProHeat Self Propelled Powerdrive The ProHeat Self Propelled home cleaning system is the first and only deep cleaner with a powerdrive The Self Propelled feature allows you to clean forward and backward using a minimum amount of effort while maximizing cleaning 1 Simply turn the Powerdrive Knob to the ON position Push the handle slightly forward to engage the powerdrive in the forward motion and pull slightly back for ease of motion on the backward pass The Powerdrive Knob may be turned to the OFF position for transporting the machine or for maneuvering around delicate furniture The BISSELL SmartClean System The ProHeat is a home cleaning system that heats hot tap water and automatically mixes it with BISSELL deep cleaning formula The solu tion is heated as it is applied to the carpet The combination of heat ed cleaning solution powered brushes and suction provide a safe and thorough method of cleaning smartlemp Temperature control automatically heats the cleaning solution as it is being applied to the car
19. lt O Operation Before You Clean Carpets Plan activities to give carpet time to dry Remove easily moved furniture from the room chairs lamps coffee tables etc Vacuum thoroughly to pick up loose debris and pet hair before using the ProHeat Plan your cleaning route to leave an exit path It is best to begin cleaning in the corner farthest from your exit OOOO Machine Preparation Set up the machine following instructions in The Features section pages 6 9 Use BISSELL deep cleaning formula in the SmartMix Tank when cleaning carpets stairs or upholstery Use clean water in the SmartMix Tank for gentle cleaning rinsing or when applying carpet protectant Choose the SmartMix setting to match the cleaning job Set the ReadyTools Dial to either Tools PreTreat or Floor Cleaning OQO OOG Pre Treating Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpet high traffic areas such as entryways and hallways or stairs Set the SmartMix Dial to High Traffic Set ReadyTools Dial to PreTreat Plug into a proper outlet and turn ON I both the Power and SmartTemp Switches While pressing the Trigger slowly make several passes over the area to be cleaned Caution Do not overwet Turn the machine Power switches OFF O and let BISSELL Deep Cleaning Formula dissolve the tough soil for 1 2 minutes before continuing 66600 Tip Try pretreating stairs or entry
20. ne when it is plugged in Do not use with damaged cord or plug a f appliance is not working as it should has been dropped damaged left outdoors or dropped into water have it repaired at an authorized Service Centre m Use indoors only Do not pull or carry by cord use cord as a handle close door on cord pull cord around sharp corners or edges run appliance over cord or expose cord to heated surfaces Do not carry the appliance while in use m Do not unplug by pulling on cord Unplug by grasping the plug not the cord m Do not handle plug or appliance with wet hands m Do not put any object into appliance openings use with blocked opening or restrict air flow m Do not expose hair loose clothing fingers or body parts to openings or moving parts m Do not pick up hot or burning objects Do not pick up flammable or combustible materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapour Do not use appliance in an enclosed space filled with vapours given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapours m Do not pick up toxic material chlorine bleach ammonia drain cleaner gasoline etc Do not modify the 3 prong grounded plug Do not allow to be used as a toy m Do not use for any purpose other than described in this User s Guide Do not operate the appliance unless the
21. oor Tool gently bend long tab right side outward and pull tool down away from nozzle Rinse thoroughly dry and store Turn Power and SmartTemp switches OFF Whern filling bottle or storing unit set Unplug power cord from the outlet SmartMix Dial to Ou AY Coil Flex Hose around storage brackets on the Tool Caddy alee Coil Power Cord around Power Cord Quick Release Remove and rinse tools in clean running water Dry and replace on tool caddy Remove Tank In Tank dispose of dirty water See Features section pages 7 9 Rinse out Tank In Tank and replace on the machine Clean out lint trap Clean out the Flow Indicator Filter each time it is used to ensure best cleaning performance Unscrew the Flow Indicator Cap lift out the red rotor and white filter Rinse all 3 parts in tap water Replace the filter with the post facing upward Replace the rotor Replace the Flow Indicator Cap turn until snug do not over tighten Wipe all exterior surface with a soft cloth Store cleaner upright in a protected dry area Note ProHeat uses water and must not be stored where there is a danger of freezing Freezing will damage internal components and void the warranty When carpet is dry vacuum again to remove hair and fuzz that the ProHeat may have loosened Pump Belt Replacement Turn the machine OFF and unplug from the wall outlet Step on the Handle Release and recline the handle down onto
22. p Cleaning formula to penetrate for 3 5 minutes Once the Precleaning is complete use the attached tool to gently scrub the stain with back and forth strokes Allow to dry Some difficult stains may require a second treatment TuroboBrush Available on select models only Assembly Unplug cleaner from the outlet before attaching TurboBrush Attach TurboBrush to the Flex Hose by pressing tool onto the Grip Trigger until button snaps into hole Make certain tool is securely in place Use Move the TurboBrush switch to the BRUSH position This activates the brush when the unit is running Place the tool directly on the soiled surface Apply downward pressure on the tool and pull towards you while pulling trigger to spray cleaning solution Release the spray trigger and move the switch to the SUCTION position Vacuum the area until no more cleaning solution can be removed Repeat steps 1 3 until no more dirt can be removed Caution Do not overwet Disconnect the TurboBrush from the Flex Hose by pushing down on the button lock and pulling straight off Once removed from the Flex Hose the TurboBrush can be cleaned A Move the switch to the SUCTION position B Rinse under running water C Check spray nozzle for dirt If necessary clean with a soft bristle brush D Replace TurboBrush in its special storage location on the Tool Caddy in back available on select models only
23. pet to safely optimize Cleaning effectiveness The Power Switch on the handle controls power to the machine both switches must be ON 1 for SmartTemp to work The SmartTemp Switch is found on the handle near the Power Switch You may choose not to use the SmartTemp feature if you are cleaning delicate wool or oriental rugs SmartTemp heats the cleaning solution for carpet and bare floor application only It does not heat solution sprayed through the accessory tools The SmartTemp Ready Light indicates when the heater is ON 1 The heater should be turned on 2 minutes before Cleaning to become fully warmed up and ready for cleaning It is found on the front of the handle where it is easy to see while you clean Smartlemp increases the water temperature approximately 25 and will not allow it to exceed 180 OO Power SmartTemp Switch Switch Smartlemp Ready Light SmartMix Provides custom solution control for each cleaning job Lift the SmartMix concentrate tank up and out of the machine base Turn the tank over so that the valve cap is in an upward position Unscrew the valve cap and fill the tank to the fill line with BISSELL deep cleaning formula d Replace the valve cap turning until snug Replace SmartMix concentrate Tank Choose the SmartMix setting that fits the cleaning job Water Rinse Carpet Protector This setting must also be used when applying the carpet prot
24. r X do not use Not recommended for use on velvet silk vinyl leather or 100 cotton upholstery If clogged soak applicator tool in hot tap water before using Plan your route to leave an exit path It is best to begin protecting in the corner farthest from your exit Apply Scotchgard protector in a slow sweeping motion with a slight overlap of the treated area For best coverage follow the guide on the cartridge ai One 8 oz cartridge protects 200 square feet 18 6 square ies meters This is equal to two average size rooms each at 10 x Lb tn 10 feet or 3 x 3 meters Periodically check the product level in the bottle to ensure best coverage Be careful not to spray the protector onto furniture or fabric that has not been tested for colorfastness If this does occur wipe off the protector Remove bottle from applicator tool If concentrate is left put the cap on and store at room temperature for later use With applicator tool still on the end of Flex Hose spray clean hot water into sink to avoid any future clogging Store tool on the back of unit in the caddy OOOO OOO G66 66 6 Important Check Upholstery Tags Check manufacturer s tag before cleaning W or WS on the tag means you can use your ProHeat If the tag is coded with X or G with a diagonal strike through or says Dry Clean Only do not proceed The Scotchgard protector is not recommended for use on
25. require service This warranty applies to product used for personal and not commercial or rental serv ice This warranty does not apply to fans or routine maintenance components such as filters bags belts or brushes Damage or malfunction caused by negligence abuse or use not in accordance with the User s Guide is not covered If your BISSELL product should require service Call BISSELL Consumer Services at the number below or www bissell com to locate a BISSELL Authorized Service Centre in your area If there are no authorized BISSELL Service Centres in your area a BISSELL Representative at canada custhelp bis sell com or at the phone number below will issue you a Return Authorization Number and a pre paid mailing label to return the unit to BISSELL for warranty repair The machine should be returned with a photocopy of your proof of purchase Your dated sales receipt is your warranty do not send original If you need information about repairs or replacement parts or if you have questions about your warranty contact Bissell Consumer Services E mail canada custhelo bissell com Or call BISSELL Consumer Services 1 800 263 2535 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Canada Corporation ATTN Consumer Services Box 1003 Niagara Falls Ontario L2E 6W2 EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY BISSELL CANADA CORPORATION IS NOT LIABLE FOR INCIDENTAL OR
26. rmulas which contain lemon or pine oil may damage this appliance and void warranty Chemical spot cleaners or solvent based soil removers should not be used These products may react with the plastic materials used in your ProHeat causing cracking or pitting Tank in Tank Our Tank in Tank system is designed with a bladder inside for clean water As you clean the bladder will empty Dirty water col lects in the tank outside the bladder O 6606 OG Step on Handle Release to lay the machine handle down out of the way Lift the Tank in Tank handle The handle locks the lid in place Carry it like a bucket to fill at the sink Note You may notice hair and debris deposits on the carpet that were loosened by the brushing action especially with newer carpets that have never been deep cleaned before This debris should be picked up and thrown away Debris that deposits in the Brush Belt should be cleaned between uses to keep the Belts running free Set the tank down and rotate the handle forward to unlatch the lid Lift off and set the lid aside Find the mouth of the Bladder and fill to the bottom of the neck with clean hot tap water Do not boil or microwave water as it can destroy the Bladder Note Fill the Bladder with clean hot tap water only Replace the Tank Lid matching the lid and tank edges Handle must be in the forward position to reinstall Rotate the handle to the carrying position to re la
27. s down firmly on the black oval gasket at the top window to make sure the two tabs on the back of the Nozzle Window are snapped into the mating slots in the main housing Re install lid refer to The Operations section page 10 Tank In Tank must be firmly seated to function remove and reseat Tank in Tank Adjust angle apply more downward pressure Empty Tank in Tank refer to The Operations section page 10 BISSELL Consumer Services For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 263 2535 Monday Friday 8 am 10 pm ET Saturday 9 am 8 pm ET Or write BISSELL Canada Corporation P O Box 1003 Niagara Falls ON L2E 6S5 ATTN Consumer Services Or visit the BISSELL website www bissell com When contacting BISSELL have model number of unit available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It provides proof of date of purchase in the event of a warranty claim See About Your Warranty on page 24 for details Please do not return this product to the store Replacement Parts BISSELL ProHeat Item Part No Part Name 1 210 9213 4 Small Area Tool 2 210 9148 Spraying Crevice Tool 3 210 1197 TurboBrush 4 214 9131 Bare Floor Tool 5 214 9142 PreTreat Wand 6 215 9155 Tough Stain Brush 7 015 9043 Tank Assembly Complete Includes Li
28. select models only PowerBrush Floor Nozzle Window Le Scotchgard BISSELL Floor Tough Stain Applicator protector a Fiber Cleansing Cleansing PreCleaner Tool cartridge TurboBrush Formula with Formula Available on select O models only n How to Use This Guide WARNING Do Not plug in your cleaner This User s Guide has been designed to help you get the utmost until you have completely satisfaction from your BISSELL ProHeat deep cleaner You ll find assembled it per the following assembly and operating instructions safety precautions as well as instructions and are familiar maintenance and troubleshooting instructions Please read this Guide with all instructions and thoroughly before assembling your deep cleaner operating procedures Pay particular attention to the product diagram assembly instructions and part names Locate and organize all parts before assembly Familiarize yourself with the parts and where they go Following this User s Guide will greatly enhance your ability to get the most performance from your BISSELL ProHeat for many years Your ProHeat comes in 3 easy to assemble components plus accessories Upper Handle Lower Handle Tool Caddy Powerdrive Knob The only tool you will need to assemble your cleaner is a Phillips head screwdriver How to Put It Together Refer to Assembly Diagram on page 4 Make sure the Powerdrive Knob is in the ON position S
29. tch the lid Replace tank in machine base seating firmly in place Rotate handle back down to the latched position Note Both the SmartMix Bottle and the clean water tank must have liquid in them for the machine to spray If one tank is empty the machine will not apply either cleaning solution or water only When It s Time to Empty Tank in Tank Q 2 Q Remove the Tank in Tank follow steps 1 and 2 above Carry the Tank in Tank like a bucket to the sink where you will dispose of the dirty water Remove Tank Lid by rotating handle forward to unlatch lid and lifting lid off tank Pour out dirty water Handle Release Fill bladder only with clean hot tap water Pour out 4 dirty water When It s Time to Empty Tank in Tank continued on the Tank Lid A Remove tank assembly from unit B Remove Tank Lid C Remove any debris caught in lint screen D Reinsert lint screen on Tank Lid The screen will Click into place Replace Tank Lid F Reinsert tank assembly into unit 5 After each use remove and rinse the lint screen located m Refill with clean tap water as above steps 5 through 9 on page 8 and refill the SmartMix Tank with BISSELL deep cleaning formula as necessary eae Screen When the cleaning job is complete rinse out the Tank in Tank by rinsing clean water between the bladder and tank Return Tank in Tank to the machine following steps 6
30. velvet silk 100 cotton upholstery vinyl or leather If manufacturer s tag is missing or not coded check with your furniture dealer Check for colorfastness in an inconspicuous place If possible check upholstery stuffing Colored stuffing may bleed through fabric when wet Plan activities to give upholstery time to dry Vacuum thoroughly to pick up loose debris and pet hair Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts Machine Preparation Set up the machine following instructions in The Features section pages 6 9 Use BISSELL Deep Cleaning Formula in SmartMix Tank Set the ReadyTools dial to Tools or PreTreat SmartTemp heats the cleaning solution for carpet and bare floor application only It does not heat solution sprayed through the accessory tools Set SmartMix Dial to Normal Cleaning Technique Choose the 4 Small Area Tool the Tough Stain Brush or the Spraying Crevice Tool and connect to the Flex Hose Plug into a proper outlet and turn Power Switch ON 1 While pressing the Trigger slowly move the spraying tool back and forth over the soiled surface Release the Trigger to suction soiled water Continue to clean soiled area working in small sections until no more dirt can be removed Caution Do not overwet When the cleaning job is complete refer to the Maintenance section for machine cleanup and storage instructions on pages 1
Download Pdf Manuals
Related Search