Home

Bissell 23T7 Vacuum Cleaner User Manual

image

Contents

1. the filters www bissell com Dess 800 2387 7691 Maintenance and care How to maintain your Vacuum To maintain maximum cleaning per formance the following maintenance A WARN NG To reduce the risk of injury from moving parts and or electrical steps must be performed 1 Clean the dirt tank if any visible clogs shock step power swiich 1o OF occur and disconnect polarized plug 2 Empty the dirt cup when the dirt reaches from electrical outlet before per the Full line on the side forming troubleshooting checks Check the inner and outer circular filters and the pre motor filter at least once a month and clean or replace as needed ad e Check rotating floor brush e remove si strings hair or debris that might interfere with the suction power Note More frequent filter clean ing or replacement may be neces sary if you are vacuuming new carpet fine dust or have allergy concerns Follow the instructions on the following pages to perform these simple maintenance steps Lower Tank Cleaning the dirt tank You have three parts to your dirt tank upper tank dirt cup and lower tank Emptying the dirt cup The dirt cup needs to be emptied when dirt reaches the Full line 1 Turn off vacuum and unplug it from electrical outlet 2 Remove dirt cup by sliding the dirt cup release lever Then pull dirt cup out lip Empty dirt into garbage container The dirt cup
2. wider than right Unplug from outlet when not in use and before conducting maintenance A WARNING To reduce the risk of fire electric shock or injury E Do not n the polarized plug to fit a non polarized outlet or extension cord Do not leave vacuum cleaner unattended when it is plugged in ER from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not allow children to operate vacuum cleaner or use as a toy Close attention is necessary when used by or near children Do not use for any purpose other than described in this User s Guide Use only manufacturer s recommended attachments Do not use with damaged cord or plug If appliance is not working as it should has Kai dropped damaged left out doors or dropped into water have it repaired at an authorized service center BI Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces BI Do not unplug by pulling on cord To unplug grasp the plug not the cord BI Do not handle vacuum cleaner or plug with wet hands BI Do not put any object into openings Do not use with any openin Bed keep openings free of dust lint hair GE Kee that may reduce air flow Bissell www bissell com BI Keep hair loose clothing fingers and all parts of body away from openings and moving
3. AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty last so the above limitation may not apply to you 15 Bissell www bissell com 800 237 7691 Don t forget to register your product Registering is quick easy and offers you benefits over the lifetime of your product You ll receive BISSELL Rewards Points Automatically earn points for discounts and free shipping on future purchases Faster Service Supplying your information now saves you time should you need to contact us with questions regarding your product Product Support Reminders and Alerts We ll contact you with any important product maintenance reminders and alerts Special Promotions Optional Register your email to receive notice of offers contests cleaning tips and more Visit www bissell com registration now BISSELL consumer services For information about repairs or replacement parts or questions about your warranty call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or write BISSELL Homecare Inc
4. Earn BISSELL Rewards Register your zc today Bissell mg mg D y EASYVaC USER S GUIDE 2377 SERIES 2 Thank You 3 Safety Instructions 4 Product View AA E TT 5 Assembly 6 7 Operations HE AAA 8 12 Maintenance and Care 13 Troubleshooting IA Replacement Parts 15 Warranty 16 Product Registration 16 Consumer Services Thanks for buying a BISSELL Vacuum We re glad you purchased a BISSELL Easy Vac floor and carpet vacuum Everything we know about floor care went into the design and construction of this complete high tech home cleaning system Your BISSELL Easy Vac is well made and we back it with a limited one year warranty We also stand behind it with a knowledgeable dedicated Consumer Services department so should you ever have a problem you ll receive fast considerate assistance My great grandfather invented the floor sweeper in 1876 Today BISSELL is a global leader in the design manufacture and service of high quality homecare products like your BISSELL Easy Vac Thanks again from all of us at BISSELL err d Sero Mark J Bissell Chairman President amp CEO 2 Bissell www bissell com 800 237 7691 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should be observed including the following READ ALL INSTRUCTIONS BEFORE USING YOUR UPRIGHT VACUUM Always connect to a polarized outlet left slot is
5. PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services Or visit the BISSELL website www bissell com When contacting BISSELL have model number of cleaner available Please record your Model Number Please record your Purchase Date NOTE Please keep your original sales receipt It provides proof of purchase date in the event of a Bissell warranty claim See Warranty on page 19 for details 2010 BISSELL Homecare Inc Grand Rapids Michigan All rights reserved Printed in China Part Number 110 4317 Rev 12 10 Visit our website at www bissell com 16 l www bissell com Dees 800 237 7691
6. eplace the brush cover and five screws 11 Bissell www bissell com 800 237 7691 Maintenance and care Replace drive belt 1 Follow steps 1 4 of previous section Drive Belt Clean and replace rotating floor brush 3 Motor Shaft 2 Check drive belt carefully for wear cuts and stressed areas If the drive belt appears worn you will need to replace it 3 Grasp old drive belt and remove from motor shaft Discard old drive belt 4 SC new drive belt over motor shaft and stretch other end over floor brush in the space provided between the bristles 5 Place ends of floor brush down into slots on sides as shown 6 Turn floor brush by hand several times in the direction of the motor shaft If properly installed drive belt will align itself on floor brush 7 Replace brush cover and five screws Cleaning stretch hose and foot hose 1 Locate the stretch hose where it connects to the dirt cup on the back of the vacuum 2 Push in and twist to release hose from the holder 3 Look to see if there is any debris in the hose Clean as necessary 4 Locate the clear foot hose under the hose holder Two Screws 5 Remove the two screws located to the left of the hose Clear Foot Hose 6 Check for any debris in the hose 7 Usea pa narrow object such as a broomstick to clean the hose Remove clogs or debris 8 Replace two screws to attach foot hose ANWAR N N G Re
7. filter located underneath the dirt cup right above the motor 2 6 Cleaning the upper tank 2 10 Turn off vacuum and unplug it from electrical outlet Remove dirt cup by sliding the dirt cup release lever to the right Then pull dirt cup out A up lower cup to access the pre motor ilter Remove the small round pre motor filter located on the base of the vacuum Remove any dust or debris from the filter Rinse well under warm water then i Pre Motor air dry thoroughly before replacing Filter Note Always make sure all filters are in place and thoroughly dry before using this vacuum Replace dirt cup and slide the dirt cup release lever to lock into place Turn off vacuum and unplug it from electrical outlet Remove dirt cup by sliding the dirt cup release lever to the right Then pull dirt cup out Twist the primary separator to unlock it and pull it down Brush off any dirt and rinse off screen with warm water Air dry completely before replacing Check hose inlet for any clogging Reassemble the pinay separator by centering the front symbol and twisting toward lock position as shown Replace dirt cup and slide lever to lock position Lock Position WARNING Do not operate cleaner with damp or wet filters or without all filters in place Bissell www bissell com Ze 800 237 7691 Maintenance and care Power cord storage EENEG When you have fini
8. le is designed so only the correct snaps will fit com fortably with the holes in the base Do not use excessive force while assembling this vacuum It should fit together with ease 4 Wrap power cord around cord wraps and place attachments in their correct holders Your vacuum assembly is now complete Handle position Press the detent lever with your foot to place your vacuum in one of three positions 1 Upright For storage and transporting 2 Normal Cleaning Press detent lever once Use for most household floor cleaning tasks 3 Low Cleaning With the vacuum in nor mal cleaning position press detent lever again Use GE reaching under low furni ture such as tables chairs or beds Bissell 5 www bissell com 800 237 7691 Operations Special tools Your BISSELL Easy Vac is not only a powerful carpet and rug vacuum cleaner it s also a versatile above floor vacuum cleaner when you select one of the special tools 1 Raise handle to upright position 2 Grasp hose and remove from hose holder 3 Attach tools by firmly pushing onto vacu um hose Crevice Tool Use in tight narrow spaces Dusting Brush Use to dust upholstery drapes blinds shelves baseboards and much more Note Brush will continue to rotate while tools are in use Transporting cleaner NOTICE The floor brush will continue to rotate while your vacuum is used for above floor 1 To move your cleaner from r
9. may be washed in warm water with a mild detergent Remove the lower tank from the bot tom before wash ing Rinse and dry thoroughly before re attaching it This is not dishwasher safe gt 7 A Put the dirt cup back in the vacuum and E in the dirt cup release handle to ock into place Note There is one clips on the base of the vacuum that the cup will fit into to ensure proper placement Bissell www bissell com 800 237 7691 Maintenance and care Cleaning the lower tank and inner outer circular filters 1 Turn off vacuum and unplug it from electrical outlet 2 2 Remove dirt cup by sliding the dirt cup release lever to the right Then pull dirt cup out ay 3 Remove lower tank 4 Grasp the circular filters and twist to unlock Pull straight up to remove 5 Separate the outer foam and the inner leated circular filters Wash them by ond in warm water Mild detergent may be used if desired Rinse well then air dry thoroughly before putting back together and SE in us tank 6 Place the filters back into the lower tank and twist to lock into place lip Vacuuming new carpet or vacuuming fine powders such as drywall dust may clog the filters so check them more fre quently Shake out or replace as necessary Bissell www bissell com 800 237 7691 Maintenance and care Cleaning the pre motor filter The pre motor filter protects the motor from debris It is the small round
10. oom to room put the handle in the upright position tilt the cleaner back on its rear wheels and push forcer cleaning To prevent carpet damage do not lean on the vacuum or let the power 2 The cleaner can also be moved by using foot tilt forward the carrying handle on the front of the vacuum 6 Bissell www bissell com 800 237 7691 Operations Using your cleaner SH 1 Remove the plastic plug guard and dispose 2 Unclip polarized plug from power cord 3 Rotate the Quick Release cord wrap towards floor and slip power cord from upper and lower cord wraps Wee MH XO Hi 4 Connect power cord plug to a polarized outlet 5 To keep the power cord out of your We while cleaning place it in the cord hoo n n by the top of the vacuum a Power Switch pedal The red power switch pedal is located 7 on the back of the cleaner under the Quick cord wraps E Quic Release 1 Step on the power switch to turn the unit E Cord On The rotating floor brush and suc Wrap tion will start 2 Step on the pedal again to turn the vacuum Pedal CO n lip Before cleaning under low furniture check for objects that might block the vacuum hose Do not pick up hard or sharp objects such as glass nails screws coins paper clips etc with vacuum Z CAUTION Before using your vacuum make sure that all filters pre motor and post motor are in place Do not operate your vacuum without
11. ord Wrap Primary Separator Easy Empty Crevice Tool 20 Power Dirt Cup are Dirt Cup Lower Tank Release Dusting Brush Ne Lever Inner and J Outer Power Switch Hose Holder Circular Pedal Filters Detent Levers Foot Hose www bissell com Bissell Zen 800 237 7691 Assem bly This user s guide has been designed to help you get the utmost satisfaction from your Easy Vac You ll find assem AN WARN I NG bly and operating instructions safety Do not plug in your vacuum clean precautions as well as maintenance er until you have completely assem and troubleshooting instructions Please bled it per the following instructions read this guide thoroughly before and are familiar with all instructions assembling your vacuum cleaner and operating procedures Pay particular attention to the prod uct diagram assembly instructions and part names Locate and organize all parts before assembly Familiarize yourself with the parts and where they Handle go Following this user s guide will greatly enhance your ability to get the most performance from your vacuum for many years Your vacuum comes in two easy to assemble components the handle and the base 1 Position the handle so the lower snap is facing the back of the vacuum Lower Snap 2 Line up the holes on the base with the snap and knob on the handle 3 Insert the handle into the base and push until you hear it lock into place Note The hand
12. parts BI Turn off all controls before plugging or unplugging vacuum cleaner BI Use extra care when cleaning stairs BI Do not pick up flammable materials lighter fluid gasoline kerosene etc or use in the presence of explosive liquids or vapors BI Do not pick up toxic material chlorine bleach ammonia drain cleaner etc BI Do not use vacuum cleaner in an enclosed space filled with vapors given off by oil base paint paint thinner some moth proofing substances flammable dust or other explosive or toxic vapors BI Do not pick up hard or sharp objects such as glass nails screws coins etc BI Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes BI Do not use without filters in place BI Use only on dry indoor surfaces BI Keep appliance on a level surface SAVE THESE INSTRUCTIONS FOR FUTURE USE THIS APPLIANCE HAS A POLARIZED PLUG To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install a proper outlet Do not change the plug in any way This model is for household use only 800 237 7691 Product view Handle UE He Stretch Hose Carrying Handle ug U Quick Tork Release C
13. place stretch hose by snapping into Do not use sharp objects such the holder as a hanger to remove clogs Note If the debris cannot be reached through the hose then fol low the instructions for cleaning the air passageway in the Clean and replace rotating floor brush section 12 aiser www bissell com 800 237 7691 Troubleshooting WARNING To reduce the risk of electric shock turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting Vacuum cleaner won t run Possible causes Remedies Vacuum cleaner is not plugged in l Check electrical plug 2 Blown fuse tripped breaker 2 Check replace fuse or reset breaker Vacuum cleaner won t pick up dirt Possible causes Remedies l Dirt cup is full 1 Empty dirt cup 2 Filter dirty 2 Check remove debris or dean 3 Hose not secure 3 Check to be sure hose is snapped into place at both ends 4 Dirt cup not in place 4 Make sure dirt cup is fully inserted and dirt cup release handle is pushed in completely 5 Vacuum path clogged 5 Visually check air passageway hose inlet and hose for anything that might be obstructing the vacuum path Carefully remove blockage 6 Rotating power brush drive belt broken 6 Replace drive belt 7 Drive belt stretched 7 Check drive belt area and remove obstructions Replace drive belt if necessary 8 Floor brush bristles worn 8 Replace floor brush 9 Floor brush jammed 9 Remo
14. shed using your ZAAWARN N G To reduce the risk of injury from moving parts and or electrical Easy Vac store the power cord on the cord wrap 1 Turn off vacuum cleaner and unplug power shock turn power switch OFF and cord disconnect polarized plug from elec 2 Loop power cord around cord wraps trical outlet before performing on back of cleaner making certain troubleshooting checks Quick Release cord wrap is pointed up towards handle 3 Clip molded plug to power cord to Secure Clean and replace rotating floor brush You should check your cleaner s rotat ing floor brush and drive belt regularly for wear or damage You should also clean the brush and brush ends b removing string hair and carpet fibers These can wrap around the brush and hamper its ability to effectively clean your carpet Also remove any debris that has accumulated under the brush cover 1 Turn off vacuum and unplug from electri cal outlet 2 Place vacuum upside down with brush roll facing upwards 3 Remove five screws as shown with a small Phillips screwdriver Lift off brush cover 5 Grasp floor brush at both ends and lift out 6 Clean strings hair and other debris e floor brush motor shaft and drive elt 7 Check floor brush for worn areas and replace if needed 8 Check air passageway for obstructions Remove debris from this area 9 When finished cleaning reposition floor brush and drive belt Then r
15. urchase by the original purchaser for one year any defective or malfunctioning part See information below on If your BISSELL product should require service This warranty applies to product used for personal and not commercial or rental service This warranty does not apply to fans or routine maintenance components such as filters belts or brushes Damage or malfunction caused by negligence abuse neglect unauthorized repair or any other use not in accordance with the User s Guide is not covered If your BISSELL product should require service Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area If you need information about repairs or replacement parts or if you have questions about your warranty contact BISSELL Consumer Services Website or E mail www bissell com Use the Customer Services tab Or Call BISSELL Consumer Services 1 800 237 7691 Monday Friday 8 a m 10 p m ET Saturday 9 a m 8 p m ET Or Write BISSELL Homecare Inc PO Box 3606 Grand Rapids MI 49501 ATTN Consumer Services BISSELL HOMECARE INC IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT BISSELL S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you EXCEPTIONS
16. ve floor brush and dean debris from brush and ends Check drive belt for any damage Other maintenance or service not included in the manual should be performed by an authorized service representative Thank you for selecting a BISSELL product Please do not return this product to the store For any questions or concerns BISSELL is happy to be of service Contact us directly at 1 800 237 7691 13 Bissell www bissell com 800 237 7691 Replacement parts BISSELL Easy Vac Item Part No 203 7592 2 203 7034 3 203 7627 4 203 7593 5 203 7032 6 203 7033 7 203 7596 O T gt 14 www bissell com Part Name Dirt Cup Drive Belt Floor Brush Inner amp Outer Circular Filter Set Crevice Tool Dusting Brush Vacuum Hose Replacement 3 Bissell AE 4 5 g i 800 237 7691 Warranty BISSELL Easy Vac This warranty gives you specific legal rights and you may also have other rights which may vary from state to state If you feed additional instruction regarding this warranty or have questions regarding what it may cover please contact BISSELL Consumer Services by E mail telephone or regular mail as described below Limited One Year Warran ty Subject to the EXCEPTIONS AND EXCLUSIONS identified below upon receipt of the product BISSELL Homecare Inc will repair or replace with new or remanufactured components or products at BISSELL s option tree of charge from the date of p

Download Pdf Manuals

image

Related Search

Related Contents

Introduction - LiveProfessor  Bladecenter Fiber Channel-Switchverwaltung: Benutzerhandbuch  File ()  Download(AKH150S)  Instrucciones de uso e instalación    La passion du musée Hommage à Jean-Louis de Cenival  Dataflex 53.033 flat panel wall mount  1452 - Instructions embarque 12x18:-  Sensixx B45L  

Copyright © All rights reserved.
Failed to retrieve file