Behringer MXB1002 Musical Instrument User Manual
Contents
1. 18 When you connect a microphone to a stereo channel on the MXB1002 the input gain is governed by the GAIN MIC control The GAIN LINE control is used to adjust the line input gain Here too the signal can be monitored visually with the Clip LED The BAL control performs two functions When you connect a microphone via the XLR connector or another signal source via the L MONO jack the BAL control determines the signal position on the stereo basis When both 1 4 jack inputs L amp R are used the BAL control adjusts the volume balance of the two sources connected Except for the GAIN MIC control and a different set of connectors the channels 9 10 feature the same control elements as the stereo channels See L5 amp L6 and 13 through 18 1 3 3 Main section 19 20 21 22 23 24 25 26 27 The LEVEL DISPLAY reads the output level of your MXB1002 Make sure that the two Clip LED s won t light up Use this switch to activate the phantom power required for condenser microphones In battery operated mode the phantom power provided is only 18 V The MON SEND control adjusts the volume level of the monitor signal provided at connector L9 Use the MASTER fader to set the overall volume level of your MXB1002 The FX SEND control allows you to adjust the level that is sent to an external effe2. 20 Please note that in battery operated mode the phantom power provided is only 18 V Channels 1 and 2 feature an additional L NE input on a balanced 1 4 jack The INSERT jack allows you to insert for example a compressor or equalizer in the mono channels These are the two balanced L NE inputs on 1 4 jacks for the left and right sides of the stereo channels which can be used in parallel to the microphone inputs Use the TAPE OUT jacks to connect for example a tape deck for recording applications The TAPE IN jacks on stereo RCA and 1 4 jacks allow for the connection of play back devices such as CD players etc Use either the RCA or the 1 4 jacks Use the PHONES jack to connect a commercially available pair of headphones These are the balanced 1 4 jack MAIN OUTPUTS of your MXB1002 that can be used to drive e g a power amplifier 9 The MON SEND connector provides the monitor signal of your MXB1002 for example to control a monitor amplifier or active monitor speaker 4 1 INTRODUCTION 10 EURORACK MXB1002 Connect the FX SEND connector to the input of an external effects device The MXB1002 has no dedicated FX Return connectors However you can connect the outputs of an external effects device to the 1 4 jack inputs of the stereo channels or channels 9 10 In this case the stereo channel s FX control must be set to ooto avoid any feedbac
3. 73 mm 11 7 298 mm 8 5 216 mm app 2 5 kg PSU not included BEHRINGER is constantly striving to maintain the highest professional standards As a result of these efforts modifications may be made from time to time to existing products without further notice Specifications and appearance may differ from those listed or shown 3 SPECIFICATIONS 7 EURORACK MXB1002 4 WARRANTY 1 WARRANTY CARD ONLINE REGISTRATION To be protected by the extended warranty the buyer must complete and return the enclosed warranty card within 14 days of the date of purchase to BEHRINGER Spezielle Studiotechnik GmbH in accordance with the conditions stipulated in 3 Failure to return the card in due time date as per postmark will void any extended warranty claims Based on the conditions herein the buyer may also choose to use the online registration option via the Internet www behringer com or www behringer de 2 WARRANTY 1 BEHRINGER BEHRINGER Spezielle Studiotechnik GmbH including all BEHRINGER subsidiaries listed on the enclosed page except BEHRINGER Japan warrants the mechanical and electronic components of this product to be free of defects in material and workmanship for a period of one 1 year from the original date of purchase in accordance with the warranty regulations described below If the product shows any defects within the specified warranty period that are not due to normal wear and tear and or improper handl
4. MXB1002 EURORACK User s Manual Version 1 0 September 2000 St www behringer com x 2 O Z m EURORACK MXB1002 SAFETY INSTRUCTIONS CAUTION To reduce the risk of electrical shock do not remove the cover or back No user serviceable parts inside refer servicing to qualified personnel WARNING To reduce the risk of fire or electrical shock do not expose this appliance to rain or moisture CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN A A This symbol wherever it appears alerts This symbol wherever it appears alerts you to the presence of uninsulated you to important operating and dangerous voltage inside the enclosure maintenance instructions in the voltage that may be sufficient to accompanying literature Read the constitute a risk of shock manual DETAILED SAFETY INSTRUCTIONS All the safety and operation instructions should be read before the appliance is operated Retain Instructions The safety and operating instructions should be retained for future reference Heed Warnings All warnings on the appliance and in the operating instructions should be adhered to Follow instructions All operation and user instructions should be followed Water and Moisture The appliance should not be used near water e g near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool etc Ventilation The appliance should be situ
5. ated so that its location or position does not interfere with its proper ventilaton For example the appliance should not be situated on a bed sofa rug or similar surface that may block the ventilation openings or placed in a built in installation such as a bookcase or cabinet that may impede the flow of air through the ventilation openings Heat The appliance should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat Power Source The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance Grounding or Polarization Precautions should be taken so that the grounding or polarization means of an appliance is not defeated Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords and plugs convenience receptacles and the point where they exit from the appliance Cleaning The appliance should be cleaned only as recommended by the manufacturer Non use Periods The power cord of the appliance should be unplugged from the outlet when left unused for a long period of time Object and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings Damage Requiring Service The applian
6. ce should be serviced by qualified service personnel when the power supply cord or the plug has been damaged or objects have fallen or liquid has been spilled into the appliance or the appliance has been exposed to rain or the appliance does not appear to operate normally or exhibits a marked change in performance or the appliance has been dropped or the enclosure damaged Servicing The user should not attempt to service the appliance beyond that which is described in the Operating Instructions All other servicing should be referred to qualified service personnel EURORACK MXB1002 EURORACK Professional 10 channel mixing console with optional battery operation and monitor plus effects paths A 10 channel mixing console with two mono channels three stereo channels and a separate stereo tape channel A Optional mains or battery operation with alkaline batteries A Separate gain controls for mic and line inputs on all stereo channels A Gold plated XLR mic connectors on all mono and stereo channels A Ultra low noise discrete mic preamplifiers on all microphone inputs A Dedicated inserts on all mono channels A Balanced 1 4 stereo jacks and balance controls on all stereo channels A Separate stereo tape channel with 1 4 and RCA jacks A Stereo output for recording applications A Ultra musical active 3 band EQ on all ten channels A Monitor and effects paths as well as separate gain controls on all channels A Hi
7. cts device via connector 10 Thus you can drive all types of effects devices without any risk of distortion The PHONES control governs the headphones volume Connect the enclosed power supply to the AC POWER IN jack Use the POWER ON switch to switch on your MXB1002 which is indicated by the LED below the LEVEL DISPLAY 19 SERIAL NUMBER Please take the time to have the warranty card filled out completely and return it within 14 days after the date of purchase so as to be entitled to benefit from our extended warranty Or use our online registration option available on the World Wide Web at www behringer com 1 INTRODUCTION 5 2 WIRING EURORACK MXB1002 Unbalanced use of mono 1 4 jack plugs Tip Signal Sleeve Ground Shield Tip Sleeve Strain relief clamp Balanced use of stereo 1 4 jack plugs Tip hot ve Ring cold ve Sleeve Ground Shield Tip Ring Sleeve Strain relief clamp For connection of balanced and unbalanced plugs ring and sleeve have to be bridged at the stereo plug Balanced use with XLR connectors Input 1 Ground Shield 2 hot ve 3 cold ve Output For unbalanced use pin 1 and pin 3 have to be bridged Fig 2 1 Various connector types Insert Send amp Return Tip Send out Ring Return in Sleeve Ground Shield Strain relief clamp Connect th
8. e insert send with the input and the insert return with the output of the effects device Headphones 1 4 connector Tip Left Signal Ring Right Signal Sleeve Ground Shield Tip Ring Sleeve Strain Relief Clamp Fig 2 2 Wiring diagram of insert cable and headphones plug 2 WIRING 3 SPECIFICATIONS INPUT CHANNELS 1 amp 2 Mic input Frequency response Gain range SNR Line input Frequency response Gain range SNR STEREO CHANNELS 3 4 7 8 amp 9 10 Frequency response Gain range SNR EQUALIZATION LOW MID HI MAIN MIX Main Outputs Mon Send FX Send Tape Out Phones Output POWER SUPPLY Mains voltage Battery life PHYSICAL Dimensions H W D Weight EURORACK MXB1002 electronically balanced discrete input configuration 10 Hz to 200 kHz 14 dB to 60 dB 120 dB E I N electronically balanced 10 Hz to 130 kHz 6 dB to 38 dB 95 dB E I N 10 Hz to 70 kHz Line ooto 15 dB Mic 13 to 60 dB Line 96 dB Mic 104 dB E I N 50 Hz 15 dB 700 Hz 15 dB 10 kHz 15 dB 28 dBu balanced 22 dBu unbalanced 22 dBu unbalanced 22 dBu unbalanced 22 dBu unbalanced 15 dBu 150 Q USA Canada 115 V 60 Hz Power Supply MXUL4 U K Australia 240 V 50 Hz Power Supply MXUK4 Europe 230 V 50 Hz Power Supply MXEU4 Japan 100 V 60 Hz Power Supply MXJP4 app 4 h with Duracell Alkaline Type MN1604 580 mAh app 1 6 40 mm 2 9
9. gh grade sealed faders and potentiometers made by ALPS A Clip LED s on all input channels A Insert option for external effects devices A Mon Send and FX Send controls in the main section for optimal level adjustment A Headphones output with dedicated volume control A Built in phantom power for condenser mics A 19 rack mounting kit included A Extremely rugged construction ensures long life even under the most demanding conditions A Manufactured under ISO9000 certified management system EURORACK MXB1002 1 INTRODUCTION Congratulations With the MXB1002 you have purchased a state of the art 10 channel mixing console that sets new standards Our prime goal when developing the MXB1002 was to design a console that can be used for a great variety of applications And to give you maximum flexibility you can operate the MXB1002 both from the mains and from batteries In combination with its comprehensive range of features and pro level connections the MXB1002 will be your perfect tool for any kind of application broadcasting video dubbing or giving the sound of your band its finishing touch 1 1 Before you begin Your EURORACK MXB1002 was carefully packed in the factory and the packaging is designed to protect the unit from rough handling Nevertheless we recommend that you carefully examine the packaging and its contents for any signs of physical damage which may have occurred during transit K If the unit is damaged please do not re
10. hotocopying and recording of any kind for any purpose without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH BEHRINGER and EURORACK are registered trademarks ALL RIGHTS RESERVED Duracell is a registered trademark with no connection whatsoever to BEHRINGER Spezielle Studiotechnik GmbH 2000 BEHRINGER Spezielle Studiotechnik GmbH BEHRINGER Spezielle Studiotechnik GmbH Hanns Martin Schleyer Str 36 38 47877 Willich M nchheide II Germany Tel 49 0 21 54 92 06 0 Fax 49 0 21 54 92 06 30 8 4 WARRANTY
11. idered a defect in materials or workmanship The warranty does not cover any such modification adaptation irrespective of whether it was carried out properly or not Under the terms of this warranty BEHRINGER shall not be held responsible for any cost resulting from such a modification adaptation 3 Free inspections and maintenance repair work are expressly excluded from this warranty in particular if caused by improper handling of the product by the user This also applies to defects caused by normal wear and tear in particular of faders potentiometers keys buttons and similar parts 4 Damages defects caused by the following conditions are not covered by this warranty A misuse neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals A connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used A damages defects caused by force majeure or any other condition that is beyond the control of BEHRINGER 5 Any repair or opening of the unit carried out by unauthorized personnel user included will void the warranty 6 If an inspection of the product by BEHRINGER shows that the defect in question is not covered by the warranty the inspection costs are payable by the customer 7 Products which do not meet the terms of this warranty will be repaired exclusively a
12. ing by the user BEHRINGER shall at its sole discretion either repair or replace the product 2 If the warranty claim proves to be justified the product will be returned to the user freight prepaid 3 Warranty claims other than those indicated above are expressly excluded 3 RETURN AUTHORIZATION NUMBER 1 To obtain warranty service the buyer or his authorized dealer must call BEHRINGER see enclosed list during normal business hours BEFORE returning the product All inquiries must be accompanied by a description of the problem BEHRINGER will then issue a return authorization number 2 Subsequently the product must be returned in its original shipping carton together with the return authorization number to the address indicated by BEHRINGER 3 Shipments without freight prepaid will not be accepted 4WARRANTY REGULATIONS 1 Warranty services will be furnished only if the product is accompanied by a copy of the original retail dealer s invoice Any product deemed eligible for repair or replacement by BEHRINGER under the terms of this warranty will be repaired or replaced within 30 days of receipt of the product at BEHRINGER 2 If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level in any country which is not the country for which the product was originally developed and manufactured this modification adaptation shall not be cons
13. k problems 1 3 2 Front panel The mono channels 1 and 2 of your MXB1002 feature the same control elements Therefore the following description of channel 1 also applies to channel 2 11 12 13 14 15 16 The GAIN MIC control determines the channel s input gain both for a microphone connected via the XLR jack and for other signal sources connected to the 1 4 jack Adjust the signal gain so that the Clip LED below the control lights up during peak signal only but never permanently In battery operated mode the Clip LED is switched off Use the PAN control to adjust the signal s position on the stereo basis Your MXB1002 comes with a 3 band equalizer the H control governs the high frequency range the M D control can be used to boost cut the midrange frequencies and the LOW control allows you to raise or lower the gain of the bass range The CHANNEL fader adjusts the volume of the corresponding channel Use the MON control to determine the channel volume sent to the monitor mix bus When set fully to the left the channel volume in the monitor mix is zero The FX control adjusts the effects volume for the corresponding channel The stereo channels 3 4 5 6 and 7 8 differ from channels 1 and 2 not only with regard to the connectors provided They also have two GAIN controls i e you can connect a microphone and a stereo line signal at the same time I 17
14. t the buyer s expense BEHRINGER will inform the buyer of any such circumstance If the buyer fails to submit a written repair order within 6 weeks after notification BEHRINGER will return the unit C O D with a separate invoice for freight and packing Such costs will also be invoiced separately when the buyer has sent in a written repair order 5 WARRANTY TRANSFERABILITY This warranty is extended exclusively to the original buyer customer of retail dealer and is not transferable to anyone who may subsequently purchase this product No other person retail dealer etc shall be entitled to give any warranty promise on behalf of BEHRINGER 6 CLAIM FOR DAMAGES Failure of BEHRINGER to provide proper warranty service shall not entitle the buyer to claim consequential damages In no event shall the liability of BEHRINGER exceed the invoiced value of the product 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW 1 This warranty does not exclude or limit the buyer s statutory rights provided by national law in particular any such rights against the seller that arise from a legally effective purchase contract 2 The warranty regulations mentioned herein are applicable unless they constitute an infringement of national warranty law The information contained in this manual is subject to change without notice No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including p
15. turn it to BEHRINGER but notify your dealer and the shipping company immediately otherwise claims for damage or replacement may not be granted Shipping claims must be made by the consignee Be sure that there is enough space around the unit for cooling and please do not place the MXB1002 on high temperature devices such as radiators etc to avoid overheating 1 2 Power supply There are two options for operating the MXB1002 When using mains power make sure the console is switched off before you connect it to the power supply Then connect it to the mains and switch the MXB1002 on using switch 26 on the rear Please note that the console and its power supply will get warm during operation which is completely normal For battery operation you ll only need two commercial 9 V batteries of the 6LR61 type Insert the batteries in the battery compartment on the bottom side of the unit To use the phantom power supply please insert another battery in the separate phantom power section of the battery compartment Your MXB1002 operates about 4 hours from high grade alkaline batteries see chapter 3 I When the unit is not in use or operates from mains power please remove the batteries 1 3 Control elements 1 3 1 Interface panel 1 Use this balanced XLR jack to connect a microphone to the MXB 1002 applies to channels 1 through 7 8 I The phantom power required for condenser mics can be activated with switch
Download Pdf Manuals
Related Search