Avaya X330W-2DS1 Network Router User Manual
Contents
1. You can now safely connect the cables to the unit LED 51 ALM TST ACT OOOO SIG AN LEDs 2 0000 Connect the Ports Connecting the E1 T1 Ports To connect a T1 E1 module to a network use a straight through RJ 48C to RJ 48C cable to connect the E1 T1 port to an RJ 48C wall jack Connecting the Ethernet Port A UTP Category 5 cable must be connected to the 100Base TX port via an RJ45 connector The maximum UTP cable length connected to the 10 100 Mbps port operating as 10 100Base T is 100 m 328 ft You can obtain appropriate cables from your local supplier If you are connecting the Fast Ethernet port to a PC or workstation you should use a crossed cable If you are connecting the Fast Ethernet port to another switch you should use a straight cable Connecting the Console Port Each Avaya X330WAN module has one serial port on the front panel for connecting a terminal a terminal emulator or a modem The serial port on the front panel is labeled Console and has an RJ 45 socket 1 Insert the RJ 45 plug on the console cable into the Console port of the Avaya X330WAN module 2 Insert the other end into the RJ 45 socket in the supplied DB 9 adapter 3 Insert the DB 9 plug into the serial COM port on the PC or terminal To connect a modem use the cable and an RJ 45 to DB 25 adapter The cable and two adapters can be found in the Avaya P330 accessory set supplied w2. Documentation e Avaya X330WAN Access Router Modules Quick Start Guide this document e Avaya X330WAN Access Router Modules Release Notes e Avaya X330WAN Access Router Modules Documentation and Utilities CD e Avaya Warranty and License Agreement CD Contents e Avaya X330WAN Access Router Modules User s Guide If any items are missing or damaged contact your supplier Insert the Module To insert an X330WAN into an Avaya P330 switch 1 2 Remove the blanking plate or other expansion module if installed Insert the WAN expansion module gently into the slot ensuring that the Printed Circuit Board PCB is aligned with the guide rails The PCB fits into the guide rails and not the metal base plate Press in the expansion module firmly until it is completely inserted into the Avaya P330 switch Gently tighten the two screws on the front panel of the expansion module by turning them Power up the Avaya P330 switch gt The self test procedure starts It takes between 30 to 60 seconds to complete gt The LEDs on the X330WAN and the Avaya P330 switch should illuminate as shown below Avaya X330WAN Expansion Module Ten seconds after startup the ALM LED lights ON for ten seconds then switches OF F The TST LED then lights for twenty seconds and afterwards switches off Thirty seconds after startup the ALM LED lights ON again Avaya P330 Switch LED Number 51 should be ON during the self test procedure
3. 1 70 414 8044 Norway 47 235 001 00 UK 44 0207 5195000 Gibraltar 31 70 414 8013 Oman 31 70 414 8057 Uzbekistan 31 70 414 8046 Greece 00800 3122 1288 Pakistan 31 70 414 8058 Yemen 31 70 414 8062 Hungary 06800 13839 Poland 0800 311 1273 Yugoslavia 31 70 414 8038 Iceland 0800 8125 Zimbabwe 31 70 414 8063 CALA Caribbean and Latin America Email caladatasupp avaya com Country Local Dial In Number Country Local Dial In Number Country Local Dial In Number Australia 1800 255 233 Korea 0 80 766 2580 Philippines 1800 1888 7798 Hong Kong 2506 5451 Malaysia 1800 880 227 Singapore 1800 872 8717 Indonesia 800 1 225 227 New Zealand 00 800 9828 9828 Taiwan 0 80 025 227 Japan 0 120 766 227 Hot Line 1 720 4449 998 Fax 1 720 444 9103 For updated information visit www avaya com support avaya com All trademarks registered trademarks service names product and or brand names are the sole property of their respective owners Copyright 2002 Avaya Inc All rights reserved Catalog No D00648 Rev 0 May 2002
4. Also the parameters used in the X330WAN must be compatible with the remote peer parameters Commands are shown as follows ip address parameters which you need to enter are shown in lt gt as follows lt net mask gt AIl CLI commands mentioned in this section are described in the Avaya P330 Reference Guide To configure a modem interface 1 Connect a terminal to the Console port of the X330WAN as described in Connecting the Console Port When prompted for a Login Name enter the default name root and press Enter 3 When prompted for a password enter the password root and press Enter You are now in Supervisor mode 4 Atthe prompt type interface Console and press Enter 5 Use the ip address lt ip_addr gt lt net mask gt command entering an IP address and net mask to be used by the remote peer to connect via its console interface to the X330WAN The console interface configured with the interface Console command must be on a different subnet from the router interfaces 6 Use the following commands to set the baud rate ppp authentication ppp chap secret and ppp timeout required to match your remote station if they differ from the default values The default values are shown in bold italic text speed lt 9600 19200 38400 gt ppp authentication lt chap none pap gt ppp chap secret lt string gt timeout absolute lt time gt The time is in minutes 7 Type asyne mode interactive The follo
5. Avaya X330W 2DS1 Access Router Module Quick Start Guide Note The X330WAN expansion modules can be installed in the following Avaya P330 switches e P333T P334T P332MF P333R P333R LB P333T PWR Embedded S W version 3 9 or higher You can see the Embedded Software versions of the switch using the dir mod_num CLI command If you need to upgrade the software obtain the latest version of the software from http www avaya com support and download it according to the instructions in the User s Guide AVAYA Important Safety Information Unpack the Module Insert the Module Connect the Ports Configure the Module Run the Web based Manager optional Important Safety Information Before installing or removing any components of a device or carrying out any maintenance work you must read the safety information provided CAUTION To avoid damage from static only hold the WAN Expansion Router Module by the edges Do not touch the top or bottom of the circuit board If possible wear a wrist strap and use an anti static bag CAUTION The Avaya P330 switch must not be operated with the expansion slot open The expansion slot should either include a sub module or be covered with the supplied blanking plate Unpack the Module Check the package contents for the following Equipment e One X330WAN Access Router Module Connection cables are not supplied
6. device 4 Enter the following commands copy running config startup config reset Configuring Fast Ethernet Interfaces AIl CLI commands mentioned in this section are described in the Avaya P330 Reference Guide To configure Fast Ethernet interfaces 1 Type interface FastEthernet 1 to enter the Interface Configuration mode The prompt changes to p33 0WAN N super if FastEthernet1 2 Usethe ip address lt ip_addr gt lt net mask gt command to assign an IP address and subnet mask to the interface 3 Type exit to return to Supervisor mode The prompt returns to p33 OWAN N super Configuring E1 T1 Interfaces All CLI commands mentioned in this section are described in the Avaya P330 Reference Guide To configure E1 T1 interfaces T 9 Use the show controllers command to check if your controller s mode is configured as E1 or T1 Use the ds1 mode lt e1 t1 gt command to change the controller s mode from E1 to T1 or vice versa Use the controller lt e1 t1 gt lt port number gt command to set the port number to be configured The prompt changes to p33 OWAN N super controller n where N is the switch number and n is the port number Use the following commands if you want to change the clock source frame type and line code parameters from their default settings clock source line internal framing sf esf for T1 lines or framing crc4 no crc4 for El lines linecode ami b8zs for T1 li
7. ith P330 switches and they are clearly marked Configure the Module Before you can set up the X330WAN module you must power on and set up the Avaya P330 stack as described in the Avaya P330 User s Guide Before using the X330WAN module you must assign an IP address via the Command Line Interface CLI or via a Telnet session to the switch where the X330 is inserted The following steps describe how to configure the X330WAN module using the Avaya CLI Establishing a Serial Connection Perform the following steps to connect a terminal to the Console port of the X330WAN for configuration of WAN parameters using the CLI 1 Use the supplied serial cable to attach the RJ 45 console connector to the Console port Connect the DB 9 connector to the serial COM port on your PC terminal 2 Use the following serial port settings on the PC 9600 baud 8 bits 1 stop bit and no parity If you connected a PC run a VT 100 emulation session You can use the Windows HyperTerminal The terminal connected to the serial port must be configured with the same settings this setting will work with any PC COM port over a DB9 to RJ45 connector 3 Press Enter When prompted for a Login Name enter the default name root 5 When promoted for a password enter the password root Establishing a Modem Connection A PPP connection with a modem can be established only after the X330WAN is config ured with an IP address and net mask
8. n to using the CLI System Requirements Minimum hardware and Operating System requirements are Pentium II 400 Mhz based computer with 128 Mb of RAM Screen resolution of 1024 x 768 pixels Microsoft Internet Explorer 5 or Netscape Navigator 4 x Windows 95 NT 4 0 server workstation or Windows 2000 server workstation Sun Microsystems Java plug in version 1 3 1_02 supplied Running the Embedded Manager J Assign an IP address to the Master Switch before starting this procedure Assign a primary management interface pmi to the X330WAN module The default pmi is the first interface you define Verify that there is communication between the Master Switch and the X330WAN using the ping command to the pmi of the X330WAN If there is no response check the IP address and default gateway of both the X330WAN and the Master Switch Open your browser Enter the URL of the switch in the form http aaa bbb ccc ddd aaa bbb ccc ddd is the IP address of the switch gt You are prompted to log into the switch The user name is root The default password for read write access is root The Web management passwords are the same as those of the CLI If you have created additional CLI user names or changed the default passwords then you can use those passwords for Web management as well gt The welcome page is displayed If the network manager has configured the system the plug in sh
9. nes or linecode ami hdb3 for E1 lines For a list of X330WAN default settings see X330WAN Default Settings gt If you are working in E1 mode go to step 4 otherwise go to step 5 Use the channel group channel no timeslots timeslot list command to specify the channel group and time slots to be mapped For example typing channel group 1 timeslots 1 3 5 7 configures time slots numbered 1 3 5 and 7 to be mapped in channel group number 1 Proceed to step 6 Use the channel group channel no timeslots timeslot list speed lt 56 64 gt command to specify the channel group time slots to be mapped and DSO speed in kbps For example typing channel group 1 timeslots 1 3 5 7 speed 64 configures time slots numbered 1 3 5 and 7 to be mapped in channel group number 1 and the DSO speed to 64 kbps The default DSO speed is 56 kbps Type exit to return to Supervisor mode The prompt returns to 330WAN N super Use the interface Serial controller group number sub interface command to configure each channel group as a virtual serial interface For example typing interface Serial 1 2 configures a serial interface on port number 1 with channel group number 2 Use the ip address lt ip_addr gt lt net mask gt command to assign an IP address and subnet mask to the interface Repeat steps 2 through 7 if you want to configure another T1 or E1 interface 10 Type exit to return to Supervisor mode The prompt returns to p33 OWAN N s
10. ould be installed auto matically If the plug in is not installed automatically there are three ways to install the plug in manually e Either install the plug in from the CD as follows 1 Close all unnecessary applications on your PC 2 Insert the Avaya P330 Documentation and Utilities CD in the CD drive 3 Click Start on the Task bar 4 Select Run 5 Type x emweb aux files plugin_1_3_1 exe where x is the CD drive letter 6 Follow the on screen instructions e Or install the plug in from the Avaya site by clicking on the link on the welcome page e Or if the network manager has placed the files on the local site install the plug in from there by clicking the link on the welcome page gt If you have the Java plug in already installed or once you have successfully installed the plug in as described above the Web based manager opens in your browser File View Actions Help Aw OLST ZALES va eona oee RA 96 HA prove a4 ih lass E F Sawm T dfgd Serial 1 0 5 Up 33 j meme IE chgfdhgf Serial 1 1 4 up chgfdhgf Serial 1 1 Documentation and Online Help Refer to the Avaya X330WAN Documentation and Utilities CD for full instructions Notes Contact Information To contact Avaya technical support From the United States Please call 1 800 237 0016 press 0 then press 73300 From o
11. tack a connection is established with the Switch CLI entity of the Master module of the stack If you want to connect to the X330WAN CLI entity use the session lt mod_num gt wan command If the IP address in the Telnet command is the address of the X330WAN router connection is established to the X330WAN CLI entity When prompted for a Login Name enter the default name root When prompted for a password enter the User Level password root in lower case letters Do NOT use uppercase letters You can now configure the X330 WAN X330WAN Default Settings The default settings for the X330WAN and its ports are determined by its embedded software These default settings are subject to change Newer versions of the software for the X330WAN can be downloaded from the Avaya Network Software Download Web site http www avayanetwork com If you wish to change the default parameters we recom mend that you use the CLI Please refer to the Avaya X330WAN User s Guide Function Default Setting Port Speed Fast Ethernet 100 Mbps Port Duplex Fast Ethernet Full Duplex Auto Negotiation Fast Ethernet Enabled WAN Mode WAN T1 Framing WAN SF Linecode WAN ami Clock Source WAN line SNMP Community public X330WAN CLI Entry Login Login name root Password root Run the Web Based Manager optional To configure the Avaya X330WAN you can use the P330 Web based Manager in additio
12. uper Changing the Primary Management Interface pmi The default pmi is the first interface you define To change the pmi 1 2 Enter one of the interface contexts as explained before If there no ip assigned on that interface use the ip address lt ip_ addr gt lt net mask gt command Use the ip routing mode rt_primary_mgmt command to set the interface as pmi The following message displays The primary management interface has changed For this change to take effect you need to copy running config startup config and then reset the device Enter the following commands copy running config startup config reset Establishing a Telnet Connection Perform the following steps to establish a Telnet connection to the X330WAN for configuration of WAN parameters Telnet directly to one of the Router IP addresses 1 2 4 5 Connect your station to the network Verify that you can communicate with the X330WAN using the ping command to the IP address of the X330WAN you chose If there is no response check the IP address and default gateway of both the X330WAN and the station From the Microsoft Windows taskbar of your PC click Start and then Run or from the DOS prompt of your PC then start the Telnet session by typing telnet lt X330WAN_IP_address gt For example telnet 149 49 32 134 You can also Telnet the IP address of the P330 stack If you Telnet the IP address of the s
13. utside the United States EMEA Europe Middle East and Africa Email csctechnical avaya com AP Asia Pacific Email sgcoe avaya com Country Local Dial In Number Country Local Dial In Number Country Local Dial In Number Albania 31 70 414 8001 Ireland 353 160 58 479 Qatar 31 70 414 8059 Austria 43 1 36 0277 1000 Israel 1 800 93 00 900 Portugal 351 21 318 0047 Azerbaijan 31 70 414 8047 Italy 39 02 7541 9636 Romania 31 70 414 8027 Bahrain 800 610 Jordan 31 70 414 8045 Russia 7 095 733 9055 Belgium 32 2 626 8420 Kazakhstan 31 70 414 8020 Saudi Arabia 31 70 414 8022 Belorussia 31 70 414 8047 Kenya 31 70 414 8049 Slovakia 31 70 414 8066 Bosnia Herzegovina 31 70 414 8042 Kuwait 31 70 414 8052 Slovenia 31 70 414 8040 Bulgaria 31 70 414 8004 Latvia 371 721 4368 South Africa 0800 995 059 Croatia 31 70 414 8039 Lebanon 31 70 414 8053 Spain 34 91 375 3023 Cyprus 31 70 414 8005 Lithuania 370 2 756 800 Sweden 46 851 992 080 Czech Rep 31 70 414 8006 Luxemburg 352 29 6969 5624 Switzerland 41 22 827 8741 Denmark 45 8233 2807 Macedonia 31 70 414 8041 Tanzania 31 70 414 8060 Egypt 31 70 414 8008 Malta 31 70 414 8022 Tunisia 31 70 414 8069 Estonia 372 6604736 Mauritius 31 70 414 8054 Turkey 800 4491 3919 Finland 358 981 710 081 Morocco 31 70 414 8055 Uganda 31 70 414 8061 France 33 1 4993 9009 Netherlands 31 70 414 8023 Ukraine 31 70 414 8035 Germany 49 69 95307 680 Nigeria 31 70 414 8056 UAE 31 70 414 8036 Ghana 3
14. wing is displayed Entering the Modem mode will occur automatically upon proprietary modem cable plug in into the console port The terminal mode would be restarted automatically upon insertion of proprietary terminal cable Use the supplied DB 25 to RJ 45 connector to plug the console cable to the modem s DB 25 connector Plug the other end of the cable RJ 45 connector to the Console port on the X330WAN gt The X330WAN enters Modem mode within one minute You can now dial from a remote station and open a Telnet session to the IP address configured in step 5 Configuring Loopback Interfaces AIl CLI commands mentioned in this section are described in the Avaya P330 Reference Guide To configure Loopback interfaces 1 Use the interface loopback lt loopback number gt command to enter the Interface Loopback mode For example typing interface loopback 1 configures a loopback with a Loopback interface number 1 The prompt changes to p33 OWAN N super if Loopbackn where N is the switch number and n is the loopback interface number 2 Usethe ip address lt ip_addr gt lt net mask gt command to assign an IP address and subnet mask to the interface 3 Type exit to return to Supervisor mode The prompt returns to p33 OWAN N super gt The following displays The primary management interface has changed For this change to take effect you need to copy running config startup config and then reset the
Download Pdf Manuals
Related Search