Home

Avaya C460 Switch User Manual

1. Example C460 1 gt show spantree Spanning tree enabled Designated Root 00 40 0d 88 06 c8 Designated Root Priority 32768 Designated Root Cost 20 Designated Root Port 1 1 Root Max Age 20 Hello Time 2 Bridge ID MAC ADDR 00 40 0d 92 04 b4 Bridge ID priority 32768 Port State Cost Priority 4 1 Forwarding 20 128 4 2 not connected 20 128 4 3 LAG member 20 128 4 4 LAG member 20 128 4 5 not connected 20 128 4 6 not connected 20 128 4 8 not connected 20 128 4 9 not connected 20 128 4 10 not connected 20 128 4 11 not connected 20 128 type q to quit or space key to continue 4 12 not connected 20 128 4 13 not connected 20 128 4 14 not connected 20 128 4 15 not connected 20 128 4 16 not connected 20 128 4 17 not connected 20 128 4 18 not connected 20 128 4 19 not connected 20 128 4 20 not connected 20 128 4 21 not connected 20 128 4 22 not connected 20 128 4 23 not connected 20 128 4 24 not connected 20 128 4 100 Avaya C460 Reference Guide 213 Chapter 2 Avaya C460 CLI Commands Output fields Field Spanning tree Designated root Description Spanning Tree Protocol status enabled or disabled MAC address of the designated spanning tree root bridge Designated Root Priority of the designated root bridge Priority Designated Root Cost Total path cost to reach the root Designated Root Port Port through which the root bridge can be re
2. Avaya C460 Reference Guide 87 Chapter 2 Avaya C460 CLI Commands set inband vlan User level read write admin Use the set inband vlan command to set the inband management VLAN The syntax for this command is set inband vlan lt vlan_num gt vlan num The number of the VLAN Example C460 1 set inband vlan 1 Management VLAN number set to 1 set intelligent multicast User level read write admin Use the set intelligent multicast command to enable or disable the IP multicast filtering application The syntax for this command is set intelligent multicast enable disable Example C460 14 set intelligent multicast enable Done set intelligent multicast client port pruning time User level read write admin Use the set intelligent multicast client port pruning time command to set the aging time for client ports The syntax for this command is set intelligent multicast client port pruning time lt time gt seconds The time in seconds 88 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 14 set intelligent multicast client port pruning time 40 Done set intelligent multicast group filtering delay time User level read write admin Use the set intelligent multicast group filtering delay time command to set group filtering time delays The syntax for this command is set intelligent multicast grou
3. ip rip rip version User level read write admin O You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode if necessary Use the ip rip rip version command to specify the RIP version running on the interface basis The syntax for this command is ip rip rip version 1 2 The possible versions of the RIP packets received and sent on an interface are 1 RIP Version 1 packets 2 RIP Version 2 packets Example To specify that RIP version 2 should be running on the basis of the interface marketing Router 1 configure if marketing ip rip rip version 2 Done ip rip send receive mode User level read write admin O You can only access this command in interface mode Type interface name at the command prompt to enter interface mode if Avaya C460 Reference Guide 57 Chapter 2 Avaya C460 CLI Commands necessary Use the ip rip send receive command to set the RIP Send and Receive mode on an interface The default state is talk listen The syntax for this command is ip rip send receive mode lt mode gt lt default route metric gt mode talk listen Set RIP to receive and transmit updates on the interface talkdefault listen SetRIP to receive updates on the interface and send only a default route default route metric Integer value Example To set the RIP Send and Receive mode on the interface m
4. set mac aging User level privileged supervisor This command is available on the P330 ML switches only Use the set mac aging command to enable or disable the MAC aging function The syntax for this command is set mac aging status status enable disable Examples C460 1 set mac aging enable mac aging is enabled C460 14 set mac aging disable mac aging is disabled set mac aging time User level privileged supervisor This command is available on the P330 ML switches only Use the set mac aging time command to set the MAC aging time in minutes This is the time after which unused MAC addresses in the MAC table are erased The syntax for this command is Set mac aging time lt aging time gt aging Aging time in minutes 1 to 3600 default 5 time Avaya C460 Reference Guide 95 Chapter 2 Avaya C460 CLI Commands Example C460 1 set mac aging time 5 mac aging time is set to 5 minutes O The entered value is the aging time lower bound The actual aging time might be up to three minutes longer set outband duplex User level read write admin Use the set outband duplex command to configure the duplex type of the Ethernet Console port You can configure the Ethernet Console interface to either full duplex or half duplex The duplex status of a port in auto negotiation mode is determined by auto negotiation and an error message is gener
5. eese teeth entente 139 set welcome message sss enne nnns 140 show access US tee co ED e cte t e pee tute ce bre s ENS 140 Show allowed managers status sess eee 141 show allowed managers table sssssssssssse 142 show arp aging interval sss eene 143 show arp txintetyal cuina eese rated tee detentus 143 Show banner loii na nenene a arae nen nnns 143 Show banner post login sees 144 show boot Dank eerte et tere rrt eode pe nidas rera euh 144 show broadcast storm control esee 144 ShOW CAaTEix i asocio RN oe e et eee e eie a Moka s ea dents 145 Show Cati flle TR CR e PR e Ree HERR e Ee a oh o eee uS 147 SHOW cani Vd eee oer eere be EQ se ed reote dus 147 show chassis identity sse enn 148 SHOW COPY Status ta tai 148 show epu load ne eee eme ene da diia 149 SAOWES feet deo id Sen eae eL tenet d tectorio tees ie ert des 149 show d vice mode cidad cont Padrino 150 IONNS L01 A D EARE ds 150 Show doti x statisties TA che e UT eE 150 show dynamic vlans sess 151 show environment fans eese eren nente nnne nnne ene 151 show environment power sse e eene enne 152 show erase Status eec eee Deve ede eres icon 153 show event log singset iiie e ei aa E RE 153 show event log Layer 3 sss eene 153 sliow fragtrient hia ance cesiete tee teretes 153 show icmp redirect i tec
6. show port trap User level read only read write admin Use the show port trap command to display information on SNMP generic link up down traps sent for a specific port The syntax for this command is show port trap module Optional port Optional Example lt module gt lt port gt Number of the module 3 6 If you do not specify a number the ports on all the modules are shown Number of the port on the module If you do not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 C460 1 gt show port trap 4 1 Port 4 1 up down trap is disabled Avaya C460 Reference Guide 197 Chapter 2 Avaya C460 CLI Commands show port vlan binding mode User level read only read write admin Use the show port vlan binding command to display port vlan binding mode information The syntax for this command is show port vlan binding mode module port module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the module If you do not specify a Optional number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 gt show port vlan binding mode port 2 1 is statically bound port
7. C460 1 set spantree hello time 2 bridge hello time set to 2 set spantree max age User level read write admin Use the set spantree max age command to set the bridge spanning tree max age parameter 132 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is set spantree max age lt seconds gt max age The max age time in seconds to keep message information before it is discarded Value ranges between 6 to 40 value must be between 2 X Bridge Hello Time 1 and 2 X Bridge Forward Delay 1 Recommended value is 20 sec Example C460 1 set spantree max age 20 bridge max age is set to 20 set spantree priority User level read write admin Use the set spantree priority command to set the bridge priority for STP The syntax for this command is set spantree priority lt bridge_priority gt bridge priority Number representing the priority of the bridge with a priority level from 0 to 65535 0 indicates high priority and 65535 indicates low priority Example C460 1 set spantree priority 4096 Bridge priority set to 4096 set spantree tx hold count User level read write admin Use the set spantree tx hold count command to limit the maximum number of BPDUs transmitted during a hello time period The syntax for this command is set spantree tx hold count rate rate Value between 1 to 10 recommended value is 3 A
8. 236 Avaya C460 Reference Guide Layer 3 CLI Commands A access list 13 arp 14 arp timeout 14 C clear arp cache 16 clear event log 18 clear fragment 18 clear ip route 19 clear ip traffic 20 clear log 20 clear power history 21 clear rmon2 statistics 22 clear screen 22 clear system log 23 clear vlan 24 configure 25 copy running config startup config 25 copy tftp startup config 28 D default metric 30 default metric RIP 30 31 E enable vlan commands 32 F fragment size 33 fragment timeout 34 H hostname 35 I interface 36 ip access default action 37 ip access list 38 ip access list cookie 39 ip access list copy 39 ip access list dscp name 40 ip access list dscp operation 40 ip access list dscp precedence 41 ip access list dscp trust 42 ip access list name 42 ip access list owner 43 ip address 43 ip admin state 44 ip bootp dhcp network 44 ip bootp dhcp relay 45 ip bootp dhcp server 46 ip broadcast address 46 ip default gateway 47 ip directed broadcast 47 ip icmp errors 48 ip max arp entries 48 ip max route entries 49 ip netbios rebroadcast 49 ip netmask format 50 ip ospf authentication key 51 ip ospf cost 51 ip ospf dead interval 52 ip ospf hello interval 52 ip ospf priority 53 ip ospf router id 53 ip proxy arp 54 ip redirect 54 ip rip authentication mode 55 ip rip default route mode 56 ip rip poison reverse 56 ip rip rip version 57 ip rip send receive 5
9. C460 1 copy tftp 12 config c C460 backup 149 49 152 36 Beginning download operation This operation may take a few minutes Please refrain from any other operation during this time KEK KKK KKK KKK KKK KE KK KEK ck KEKE KKK KKK KEKE KEKE KEKE KKK KKK KEKE KEK KKK KK KR KK ck ck o ck ck ko ko kx ko KKK If you are currently running the C460 Device Manager application it is recommended to exit from it before performing configuration download operations kkkkxkxkkkxkxkxkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkxkk copy tftp startup config User level read write admin Use the copy tftp startup config command to copy the C460 configuration from the saved TFTP file to the Startup Configuration NVRAM The syntax for this command is copy tftp startup config lt filename gt lt ip gt filename file name full path ip The ip address of the host Example Router 1 gt copy tftp startup config c C460 router1 cfg 192 168 49 10 copy tftp SW_imageA User level read write admin Use the copy tftp SW_imageA command to update the software image in Bank A of all the Supervisor Modules installed in the switch To use this command you need to have an active tftp server and to create a file into which to download the data If Avaya MultiService Network Manager is running you do not require an 28 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands addit
10. Fragments 0 reassembled 0 timeouts 0 couldn t reassemble 0 fragmented Sent 19442 generated 0 forwarded 0 no route 0 discarded ICMP statistics Received 881 total 3 ICMP errors 0 unreachables 0 time exceeded 0 parameter 0 quench 861 echo 17 echo reply O timestamps request 0 timestamp reply type q to quit or space key to continue 0 mask requests 0 mask replies 0 redirects Sent 311 total 0 ICMP errors 433 unreachables 0 time exceeded 0 parameter 0 quench 17 echo 861 echo reply 0 timestamps request 0 timestamp reply 0 mask requests 0 mask replies 0 redirects 166 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands OSPF statistics Received 25783 total 0 checksum errors 0 hello 0 database desc O link state reg 0 link state updates 0 link state acks Sent 0 total ARP statistics type q to quit or space key to continue Received 2191321 requests 778439 replies Sent 443 requests 340 replies 0 proxy DHCP statistics Requests 0 Replies 0 BOOTP statistics Requests 0 Replies 0 show ip unicast cache User level read only read write admin Use the show ip unicast cache command to list the entries in the hardware unicast cache database The syntax for this command is show ip unicast cache lt ip addr gt ip addr IP address Avaya C460 Reference Guide 167 Chapter 2 Avaya C460 C
11. Address MAC Address Dynamic 14355 show ip route User level read only read write admin Usethe show ip route command to display IP routing table entries The syntax for this command is show ip route Example C460 1 gt show ip route Network Mask Next Hop Interface 149 49 50 0 255 255 255 0 149 49 50 233 inband 0 0 0 0 0 0 0 0 149 49 50 1 inband Source LOCAL STATIC show ip route Layer 3 User level read only read write admin Use the show ip route command to display information about the IP unicast Avaya C460 Reference Guide 163 Chapter 2 Avaya C460 CLI Commands routing table The syntax for this command is show ip route Router 1 gt show ip route Network Mask Next Hop Interface Source 149 49 77 0 255 255 255 0 149 49 77 70 inband LOCAL 0 0 0 0 0 0 0 0 149 49 77 1 inband STATIC show ip route best match User level read only read write admin Use the show ip route best match command to display a routing table for a destination address The syntax for this command is show ip route best match dst addr gt dst addr IP address Example Router 1 show ip route best match 199 93 0 0 Searching for 199 93 0 0 Showing 1 rows Network Mask Interface Next Hop Cost TTL Source 199 93 0 0 255 255 00 e 135new 135 64 76 1 1 n a STAT HI show ip route static User level read write admin Use the show ip static route comm
12. Avaya C460 Reference Guide 209 Chapter 2 Avaya C460 CLI Commands show secure current User level read write admin Use the show secure current command to list the IP addresses of managers currently connected to the switch The syntax for this command is show secure current Example C460 1 show secure current IP Address Time Since Last Request In Sec 135 64 100 205 7 149 49 77 13 13 149 49 77 7 2 C460 1 210 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show snmp User level read only read write admin Use the show snmp command to display SNMP information The syntax for this command is show snmp Example Community Access read only read write trap Trap Rec Address 192 138 40 59 C460 1 gt show snmp Authentication trap disabled Community String public public public Status Enabled Traps Configured config fault trafic_threshold module_De Enrollment module_Enrollment delete_SW_redundancy_entry create_SW_redundancy_entry temperature_warning general_threshold cam_change duplicate_ip ip_vlan_violation link_aggregation_connection_fault link_aggregation_connection_return link_aggregation_partial_fault link_aggregation_partial_return link_aggregation_auto_neg_fault link_aggregation_auto_neg_fault_return delete_lag create_new_lag active_policy_list_change policy_access_control_violation PSU_module_fault PSU_module_fault_return fa
13. The syntax for this command is show port edge state lt module port gt module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the module If you do not specify a number Optional all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 gt show port edge state Port admin state oper state 1 1 edge port edge port 1 2 non edge port non edge port show port flowcontrol User level read only read write admin Use the show port flowcontrol command to display per port status information related to flow control The syntax for this command is show port flowcontrol lt module gt lt port gt module Number of the module 3 6 If you do not specify a number all Optional modules are shown port Number of the port on the module If you do not specify a Optional number all ports on the specified module are shown 194 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show port flowcontrol 3 4 Port Send Flowcontrol Receive Flowcontrol Admin Oper Admin Oper 3 4 off off off off Output Fields Field Description Port Module and port number Send Send flow control administration Possible settings Flowcontrol e ON indicates that the local port is allowed to sen
14. not active direction rx copy only incoming traffic both copy both incoming and outgoing traffic 110 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 set port mirror source port 3 9 mirror port 4 10 direction both Mirroring both Rx and Tx packets from port 3 9 to port 4 10 is enabled set port name User level read write admin Use the set port name command to configure a name for a port If you do not specify a name the port name remains blank The syntax for this command is set port name lt module gt lt port gt value module Number of the module 3 6 port Number of the port on the module If you do not specify a number the same name is set for all the ports on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 value Name up to 16 characters Example C460 1 set port name 4 21 arthur Port 4 21 name set If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york set port negotiation User level read write admin Usethe set port negotiation command to enable or disable the link negotiation protocol on the specified port This command applies to Fast Ethernet or Gigabit Ethernet ports When negotiation is enabled the speed and duplex of the Fast Ethernet ports are determined by aut
15. 92 4 5 1645 sodot ed 68 42 252 68 48 134 show rmon alarm User level read only read write admin Use the show rmon alarm command to display the parameters set for a specific alarm entry that was set using the rmon alarm command on Page 75 or using the C460 Manager The syntax for this command is show rmon alarm lt Alarm Index gt Alarm Index History index defined using rmon alarm command or the C460 Manager 202 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show rmon alarm 1026 alarm alarm 1026 is active owned by amir Monitors ifEntry 1 1026 every 60 seconds Taking delta samples last value was 1712 Rising threshold is 10000 assigned to event 1054 Falling threshold is 10 assigned to event 1054 On startup enable rising or_falling alarms show rmon event User level read only read write admin Use the show rmon event command to show the parameters of an Event entry defined by the rmon event command on Page 76 or using the C460 Manager The syntax for this command is show rmon event lt Event Index gt Alarm Index History index defined using rmon event command or the C460 Manager Example C460 1 gt show rmon event 1026 event Event 1054 is active owned by amir Description is event for monitoring amir s co Event firing causes log and trap to community public last fired 0
16. clear ip traffic User level read write admin Use the clear ip traffic command to clear the ip traffic statistics counters The syntax for this command is clear ip traffic Example Router 1 clear ip traffic clear log User level read write admin Use the clear log command to clear port mirror User level read write admin Use the clear port mirror command to cancel port mirroring The syntax for this command is clear port mirror lt source module gt lt source port gt lt dest module gt lt dest port gt source module Source module number 20 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands source port Source port number dest module Destination module number dest port Destination port number Example C460 1 clear port mirror 9 2 10 4 this command will delete the port mirror entry do you want to continue Y N y Mirroring packets from port 9 2 to port 10 4 is cleared clear port static vlan User level read write admin Use the clear port static vlan command to delete VLANs statically configured on a port The syntax for this command is clear port static vlan module port range vlan num module port range Port range vlan num The VLAN to unbind from the port Example C460 1 clear port static vlan 3 10 5 VLAN 5 is unbound from port 3 10 clear radius authentication server User level read write admin Removes a primary or
17. ip unicast cache networks detailed NetworkMask IP Address 192 168 6 0 24 192 168 6 40 92 168 6 53 92 168 6 64 show ip unicast cache nextHop User level read write admin Usethe show ip unicast cache used as next hop routers The syntax for this command is nextHop command to list the routers that are show ip unicast cache nextHop Example Next Hop 92 168 4 92 168 5 1 Showing 2 rows Router 1 show ip unicast cache nextHop Avaya C460 Reference Guide 169 Chapter 2 Avaya C460 CLI Commands show ip unicast cache summary User level read only read write admin show ip virp Use the show command to display the number of host networks and next hops in the module s unicast cache The syntax for this command is show ip unicast cache summary Example Cache Summary Hosts a 71 Networks 24 Next Hops 37 Router 1 gt show ip unicast cache summary User level read only read write admin Use the show vrrp command to display VRRP information The syntax for this command is show ip vrrp lt vlan gt router id lt vr id gt detail vlan router id vr id detail Filter by VLAN Filter by virtual router ID 1 255 The virtual router ID Provide detailed information Example Router 1 gt show ip vrrp VRRP is globally enabled VLAN VRID IP Address PriTimer State Since lt T
18. EOS A AA o e AS AAA T e te C 241 x Avaya C460 Reference Guide Chapter 1 Using the CLI This chapter describes the Avaya C460 CLI architecture and conventions and provides instructions for accessing the Avaya C460 for configuration purposes The configuration procedure involves establishing a Telnet session or a serial connection and then using the Avaya C460 s internal CLI For details on establishing a connection see the User s Guide that accompanies the switch The CLI is command line driven and does not have any menus To activate a configuration option you must type the desired command at the prompt and press Enter You can also configure your Avaya C460 using the C460 Manager with its graphical user interface For details see the Device Manager chapter in the User s Guide that accompanies the switch and the Avaya MSNM C460 Device Manager User s Guide on the Documentation and Utilities CD CLI Architecture The C460 supports both Layer 2 switching and Layer 3 switching The C460 CLI includes two CLI entities to support this functionality e The Switch CLI entity is used to manage Layer 2 switching e The Router CLI entity is used to manage Layer 3 switching To switch between the entities use the session command For details see Avaya C460 Sessions below Configuration of the password commands and community commands in one entity is automatically attributed to the other entity in the switch Avaya C460
19. SNMP and TELNET if it is not the IP address owner Usethenoip vrrp override addr owner command to discard these packets Avaya C460 Reference Guide 63 Chapter 2 Avaya C460 CLI Commands The syntax for this command is no ip vrrp lt vr id gt override addr owner vr id Virtual Router ID 1 255 Example Router 1 configure if marketing 4 ip vrrp 1 override addr owner Done ip vrrp preempt User level read write admin O You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip vrrp preempt command to configure the router to preempt a lower priority master for the virtual router ID Use the no ip vrrp preempt command to disable preemption for the virtual router instance By default preemption is enabled The syntax for this command is no ip vrrp lt vr id gt preempt vr id Virtual Router ID 1 255 Example Router 1 configure if marketing ip vrrp 1 preempt Done ip vrrp primary User level read write admin You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip vrrp primary command to set the primary address that shall be used as the source address of VRRP packets for the virtual router ID Use the no ip vrrp primary command to return to the default primary address 64 Avaya C460 Reference
20. The syntax for this command is show ip ospf Example Router 1 show ip ospf 160 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show ip ospf database show ip ospf i User level read only read write admin Use the show ip ospf database command to display lists of information related to the OSPF database for a specific router The syntax for this command is show ip ospf database asbr summary router network network summary external asbr summary Displays information only about the autonomous system boundary router summary LSAs Optional external Displays information only about the external LSAa Optional network Displays information only about the network LSAa Optional network summary Displays information only about the network LSAa summary Optional router Displays information only about the router LSAs Optional Example Router 1 super show ip ospf interface nterface User level read only read write admin Displays the OSPF related interface information The syntax for this command is show ip ospf interface lt interface name gt interface name The OSPF interface name Example Router 1 show ip ospf interface Avaya C460 Reference Guide 161 Chapter 2 Avaya C460 CLI Commands If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new
21. The syntax for this command is show port classification module port module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the module If you do not Optional specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 gt show port classification 4 8 Port Port Classification 4 8 regular C460 1 gt show port classification 4 9 Port Port Classification 4 9 valuable 190 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show port dot1x User level read only read write admin Use the show port dot1x command to display all the configurable values associated with the authenticator port access entity PAE and backend authenticator The syntax for this command is show dot1x mod port mod Number of the module Optional port Number of the port on the module or range of ports Optional Example C460 1 gt show port dotix 3 3 Port Auth BEnd Port Re Quiet ReAuth Server Supp Tx Max Number State State Control Status Auth Priod Priod Tmeout Tmeout Priod Req 1 3 Init Init Auto Unauth Disa 60 3600 30 30 30 2 module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the mod
22. falling event startup alarm owner Example lling threshold falling event startup alarm gt This is the alarm index number of this entry it is advisable to use the same interface number as your alarm index number This is the MIB variable which will be sampled by the alarm entry The interval between 2 samples This can be set to either delta the difference between 2 samples or an absolute value This sets the upper threshold for the alarm entry The RMON event entry that will be notified if the upper threshold is passed This sets the lower threshold for the alarm entry The RMON event entry that will be notified if the lower threshold is passed The instances in which the alarm will be activated The possible parameters are Rising Falling risingOrfalling Owner name string C460 1 rmon delta rising threshold 10000 1054 falling threshold 10 1054 risingOrFalling gregory alarm 1026 was created successfully alarm 1026 1 3 6 1 2 1 16 1 1 1 5 1026 60 Avaya C460 Reference Guide 75 Chapter 2 Avaya C460 CLI Commands rmon event rmon history User level read write admin Use the rmon event command to create an RMON event entry The syntax for this command is rmon event lt Event Number gt lt type gt description lt description gt owner lt owner gt event number This is the event index number of this entry type The type of the event The possible
23. values to the default settings The syntax for this command is clear dotix config Example C460 1 super clear dotix config Original Configuration was Restored clear dynamic vlans User level read write admin Use the clear dynamic vlans command to clear dynamically learned VLANs Only the VLANs learned by the switch from incoming traffic are cleared using this command The syntax for this command is Clear dynamic vlans Avaya C460 Reference Guide 17 Chapter 2 Avaya C460 CLI Commands Example C460 1 clear dynamic vlans This command will delete all the vlans that were dynamically learned by the device do you want to continue Y N y Dynamic vlans were deleted from device tables clear event log User level read write admin Use the clear event log command to delete the log file of a Supervisor module The syntax for this command is clear event log lt module_number gt spv num Number of Supervisor Module 1 to 2 Optional Example C460 1 clear event log Clearing the reset file do you want to continue Y N y C460 1 clear fragment User level read write admin Use the clear fragment command to restore fragment action database defaults and free all waiting fragments The syntax for this command is clear fragment Example Router 1 clear fragment Done 18 Avaya C460 Reference Guide Chapte
24. 15 Example Router 1 configure router ospf 4 default metric 10 Done 30 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands default metric RIP User level read write admin O You can only access this command in the RIP context Type router rip at the command prompt to enter interface mode if necessary Use the default metric command to set the interface RIP route metric Use the no default metric command to restore the default value The default metric is 1 The syntax for this command is no default metric number number The interface RIP route metric value The range is 1 to 15 Example Router 1 configure router rip default metric 10 Done disable interface User level read write admin Usethe disable interface command to disables the inband or outband interface The syntax for this command is disable interface outband inband outband Disables the outband interface inband Disables the inband interface Example C460 1 disable interface outband You must reset the device in order for the change to take effect Avaya C460 Reference Guide 31 Chapter 2 Avaya C460 CLI Commands enable interface User level read write admin Use the enable interface command to enable the inband and outband interfaces The syntax for this command is en able interface outband inband outband Enables the outband interface in
25. 2 2 is statically bound port 2 3 is statically bound port 2 4 is statically bound port 2 5 is statically bound port 2 6 is statically bound port 2 7 is statically bound port 2 8 is statically bound port 2 9 is statically bound port 2 10 is statically bound show powerinline User level read only read write admin Use the show powerinline command display the port powerinline configuration The syntax for this command is show powerinline lt module_number port_number gt module Number of the module 3 6 If you do not specify a number optional the ports on all the modules are configured 198 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands port optional Number of the port on the module If you do not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example to show PoE configuration on I O module 3 C460 1 gt show powerinline 3 Port Inline Powering Operational Priority Status 3 1 Fault Low 312 Fault Low 3 3 Fault Low 3 4 Searching Low 3 5 Searching Low 3 6 Searching Low 3 7 Searching Low Output fields Field Description Inline operational status Powering Priority show powerinline budget Disabled Detection process in administratively disabled Searching No PD connected Delivering power Valid PD connected and power
26. 4 5 13 for ports 5 to 13 on module 4 Example to display the status for port 4 on switch 3 C460 1 gt show port 3 4 Port Name Status Vlan Level Neg Dup Spd Type 3 noname no link 1 0 enable half 10M 10 100BaseTx Port Show Port Output Fields Field Description Port Switch and port number Name Name of port Status Status of the port connected faulty disabled Vlan VLAN ID of the port Level Priority level of the port 0 7 Neg The autonegotiation status of the port enabled disabled Dup Duplex setting for the port full half Speed Speed setting for the port 10 100 1000 Type Port type for example 10 100BASE IX GBIC SX GBIC LX GBIC not present GBIC unknown Avaya C460 Reference Guide 187 Chapter 2 Avaya C460 CLI Commands show port auto negotiation flowcontrol advertisement User level read write admin Use the show port auto negotiation flowcontrol advertisement command to display the flowcontrol advertisement for a Gigabit port used to perform auto negotiation The syntax for this command is set auto negotiation flowcontrol advertisement module port mode module Number of the module 3 6 If you do not specify a number Optional the ports on all the modules are shown port Number of the port on the module If you do not specify a Optional number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 1
27. 49 152 36 copy running config startup config User level privileged supervisor Use the copy running config startup config command to copy the active policy configuration to the startup configuration file in the NVRAM Avaya C460 Reference Guide 25 Chapter 2 Avaya C460 CLI Commands The syntax for this command is copy running config startup config Example C460 1 copy running config startup config 1 copy running config tftp User level privileged supervisor Use the copy running config tftp command to upload the policy configuration to a TFTP server The syntax for this command is copy running config tftp lt filename gt lt ip gt filename Destination file name in the tftp server full path ip The ip address of the tftp server Example for Windows C460 1 copy running config tftp c c460 startup cfg 149 49 100 41 Example for Unix C460 1 copy running config tftp folder c460 startup cfg 149 49 100 41 copy startup config tftp User level privileged supervisor Use the copy startup config tftp command to download a policy configuration from a TFTP server The syntax for this command is copy startup config tftp lt filename gt lt ip gt filename Destination file name in the tftp server full path ip The ip address of the tftp server 26 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example for
28. CAM table entries for a specific module and port MACs associated with LAGs appear under the LAG ID not under the LAG port By Module and Port The syntax for this command is show cam module port mac addr MAC address module Number of the module 3 6 If you do not specify a number all Optional modules are shown port Number of the port on the module If you do not specify a Optional number all ports on the specified module are shown Avaya C460 Reference Guide 145 Chapter 2 Avaya C460 CLI Commands Example Dest MAC Route C460 1 gt show cam Total Matching CAM Dest vlan 00 00 3b 80 49 00 02 b3 07 92 00 03 47 6d e2 Dest MAC Route 08 00 20 c6 98 08 00 20 c4 c8 00 00 5e 00 01 00 00 5e 00 01 00 01 02 de 96 00 02 2d 47 18 00 02 2d 48 18 00 02 55 5b b1 00 02 b3 23 94 00 02 b3 23 a0 00 02 b3 23 ca 00 02 b3 23 ce 00 02 b3 2d 2a 00 03 47 6d e2 00 04 0d 00 56 type q to quit or space key to continue Destination Ports 5f 51 LTC 01 02 2f 67 29 el 4f 4d d3 f2 02 69 68 b9 78 1 RREPRRRPRRRRPRRRAPAR AR O PR Dest vlan 00 04 0d 00 56 00 04 0d 01 81 00 04 0d 01 b0 85 il 8c al 00 1 Entries Displayed 128 Destination Ports 146 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show cam mac User level read only read write admin Use the show cam mac command to disp
29. Guide Chapter 2 Avaya C460 CLI Commands for the virtual router instance By default the primary address is selected automatically by the device The syntax for this command is no ip vrrp lt vr id gt primary lt ip address gt vr id Virtual Router ID 1 255 ip address Primary IP address of the virtual router This address should be one of the router addresses on the VLAN Example Router 1 configure if marketing ip vrrp 1 primary 192 168 66 23 Done ip vrrp priority User level read write admin O You can only access this command in Interface mode Typeinterface name atthe command prompt to enter Interface mode if necessary Use the ip vrrp priority command to set the virtual router priority value used when selecting a master router Use the no ip vrrp priority command to restore the default value The syntax for this command is no ip vrrp lt vr id gt priority lt pri value gt vr id Virtual Router ID 1 255 pri value The priority value The range is 1 254 Example To set the priority value for virtual router 1 to 10 Router 1 configure if marketing ip vrrp 1 priority 10 Done Example Avaya C460 Reference Guide 65 Chapter 2 Avaya C460 CLI Commands ip vrrp timer line To set the virtual router simple password for virtual router 1 to abcd Router 1 configure if marketing ip vrrp 1 auth key abcd Done Use
30. If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the set vlan command to create a router Layer 2 interface The syntax for this command is set vlan lt vlan id gt name lt vlan name gt vlan id Interface Index vlan name Interface name used in layer 3 protocols Example C460 1 configure set vlan 2 name vlan2 If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york set web aux files url User level read write admin Use the set web aux files url command to allow the Device Manager to automatically locate the URL of the Web server containing the Device Manager help files and Java plug in Tip Ensure that the Web server is always accessible to prevent potential delays to Web access to the device The syntax for this command is set web aux files url lt IP address directory name gt Avaya C460 Reference Guide 139 Chapter 2 Avaya C460 CLI Commands Example C460 1 set web aux files url 192 168 47 25 emweb aux files If you wish to define a directory name which includes spaces you must enclose the entire name in quotation marks for example new york set welcome message User level read write admin Use the set welcome message command to set a welcome message to appea
31. KEK KKK ck ck ck ck ck ck ck ck ck ck ck ko ck ck ko ko kx ko If you are currently running the C460 Device Manager application it is recommended to exit from it before performing configuration download operations kkxkxkxkxkxkxkxkkxkkkkkxkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkxkkkkkkkkkkkxkxk Avaya C460 Reference Guide 29 Chapter 2 Avaya C460 CLI Commands default metric User level read write admin You can only access this command in interface mode Type interface name at the command prompt to enter interface mode if necessary Use the default metric command to set the interface RIP route metric Use the no default metric command to restore the default value The default metric is 1 The syntax for this command is no default metric rip interface metric rip interface metric The interface RIP route metric value The range is 1 to 15 Example Router 1 configure if marketing default metric 10 Done default metric OSPF User level read write admin O You can only access this command in the OSPF context Type router ospf at the command prompt to enter interface mode if necessary Use the default metric command to set the interface OSPF route metric Use the no default metric command to restore the default value The default metric is 1 The syntax for this command is no default metric number number The interface RIP route metric value The range is 1 to
32. L AE FE HE FE FE HE FE FE FE FE HE FE EE FE FE FE FE FE FE FE HE FE HE FE HE HE HE HE FHE HE EE HE FHE FE FE HE HE HE HE FHE HE FHE HE HE HE EH HE HE FHE HE FE HE FE HE HE HE HE EHH EEF E SPV INFO T FE E HE HH HE HE HE HE HE EH HE HE EE HE HE HE HE HE HE HE HE HE HE HE FE HE HE FE HE HE HH HH HHH HH HH HE E Slot d 1 E SPV state Active E Blade type M460ML SPV E Blade CS 0 2 E Serial 0000009 E 4 SW versions bank A B 1 0 5 1 0 5 E 1 Embedded Web SW version 1 0 10 E T FE AE HE HH HE HE aE HE HE EE HE HE EH HE HE HE HE HE HE HE HE HE HE HE HE HE HE HE FE HE HE FE HE HE FE HE HHH HHH HH FHE HE HE HE HE HE HE HE HE HE HEHHE E S BUM INFO LEH HH HE HE aE HE HE EE HE HE EH HE HE HE HE HE HE HE HE HE HE HE HE HE HE HE FE HE HE FE HE HH HHH HH HE FHE HE HE HE type q to quit or space key to continue E 14 Slot 2 E 4 SPV in slot 2 is not present L FE AE HE HH HE HE HE HE HE HE HE HE HE EE HE HE HE HE HE HE HE HE HE HE HE HE a HE FE HE HE FE HE HE FE HE HE HE HHH HH HE E IOBLADE INFO T FE E HE HH HE HE HE HE HE HE HE HE HE EH HE HE HE HE HE HE HE HE HE HE HE HH HE a HE HE FE HE HE HE HE HHH HH HH HE HE HE HE HE HE HE HE HEHHE E 4 Slot 3 is empty E LH HH HE HE aE HE HE HE FE HE HE EH HE HE EH HE HE HE HE TEE TEE TEE HE HE HE HE HE FE HERE HERE HE HE HE HHH HH HH HE E IOBLADE INFO T FE AE HE HH HE HE aE HE HE EE HE HE EH HE HE HE HE HE HE HE HE HE HE HE HE HE HE HE HE HH HH HE H
33. Manager C460 14 no rmon alarm 1026 no rmon event User level read write admin Use the no rmon event command to delete an existing RMON event entry The syntax for this command is no rmon event lt Event Index gt Event Index History index defined using rmon event command or C460 Manager C460 14 no rmon event 1054 68 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands no rmon history no username User level read write admin Use the no rmon history command to delete an existing RMON history entry The syntax for this command is no rmon history lt History Index gt History Index User level read only read write admin History index defined using rmon history command or RMON management tool Example C460 1 no rmon history 1026 User level admin Usethe no username command to remove a local user account The syntax for this command is no username lt name gt name User name Example C460 1 super no username john User account removed If you wish to delete a name which includes spaces you must enclose the entire name in quotation marks for example new york O You cannot delete the default user account root nvram initialize User level read write admin Use the nvram initialize command to reset the configuration parameters to their factory defaults on the Active and Standby Supervisor modules
34. Use the validate group command to verify that all the rules in a policy list are valid O If there is a configuration problem with a specific rule or with a number of rules detailed error messages will be given The syntax for this command is validate group lt policy list number gt quiet quiet does not display error messages Example Router 1 configure validate group 101 List 101 is valid O The validation process may take some time to complete 230 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands validate policy list User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the validate policy list command to verify that all the rules in a priority list are valid O If there is a configuration problem with a specific rule or with a number of rules detailed error messages will be given The syntax for this command is validate policy list lt policy list number gt quiet quiet does not display error messages Example C460 1 configure validate policy list 101 Avaya C460 Reference Guide 231 Chapter 2 Avaya C460 CLI Commands 232 Avaya C460 Reference Guide Layer 2 CLI Commands B banner login 15 banner login line 15 banner post login 15 banner post login line 16 C clear cam 17 clear dynamic v
35. User level admin Use the set ppp chap secret command to configure the shared secret used in PPP sessions with CHAP authentication The chap secret is not transferable via the configuration upload download mechanism The syntax for this command is set ppp chap secret lt chap secret gt chap secret The shared secret 4 to 32 characters Example C460 1 super set ppp chap secret hush PPP shared secret for CHAP authentication is set set ppp incoming timeout User level read write admin Use the set ppp incoming timeout command to set the number of minutes until the system automatically disconnects an idle PPP incoming session Avaya C460 Reference Guide 123 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set ppp incoming timeout lt time gt time The timeout in minutes Example C460 1 set ppp incoming timeout 15 PPP incoming session will automatically disconnect after 15 minutes of idle time qset radius authentication enable disable User level read write admin Enables or disables RADIUS authentication for the C460 switch The syntax for this command is set radius authentication enable disable enable Enable RADIUS authentication disable Disable RADIUS authentication default Example C460 1 super set radius authentication enable set radius authentication retry number User level read write admin Sets the number of times an a
36. accessibility of other networks and the cost or metric to reach the other networks LSA Link State Advertisement A broadcast packet used by Link State Protocols that contains information about neighbors and path costs LSAs are used by receiving routers to maintain their routing tables MAC Address Media Access Control Address The MAC Address is a hardware address that uniquely identifies each node of a network MAC Layer In IEEE 802 networks the MAC layer is a sublayer of the Data Link Control DLC layer The MAC layer interfaces directly with the network media Each different type of network media therefore requires a different MAC layer MAC List A list of MAC Addresses of devices that are allowed to access the network through the selected port Each port can have a MAC List If the port s security option is enabled no device can access the port unless the device s address is on the port s MAC List MAN Metropolitan Area Network A data communications network designed for a town or city Usually characterized by high speed connections using fiber optical cable or other digital media MIB Management Information Base A database of network management information that can be monitored by a Network Management System Both SNMP and RMON 248 Avaya C460 Reference Guide Glossary use standardized MIB formats that enable any SNMP and RMON tool to monitor any device defined by a MIB Module A self contained
37. added to the table set arp aging interval User level read write admin Use the set arp aging interval command to set the ARP table aging interval for gateways entries in the agent ARP table The MAC value for the default gateway of the agent in the ARP table is deleted at the end of every aging interval The default value is 10 minutes The syntax for this command is set arp aging interval lt value gt value The number representing the interval from 0 10 minutes Example C460 1 set arp aging interval 10 ARP table aging interval for gateways was set to 10 minutes set arp tx interval User level read write admin Sets the keep alive frames sending interval Setting the interval to 0 disables the transmission of the keep alive frames The syntax for this command is set arp tx interval lt inband outband gt lt value gt inband outband e Inband inband interface e Outband outband interface value The interval in seconds 0 3600 Avaya C460 Reference Guide 81 Chapter 2 Avaya C460 CLI Commands set boot bank Example C460 1 set arp tx interval 15 ARP tx interval was set to 15 seconds User level read write admin Use the set boot bank command to set the system boot bank for the active Supervisor Module The syntax for this command is set boot bank lt value gt value e bank a set the boot bank to A e bank b set the boot bank to
38. address and mask to an interface The syntax for this command is ip address lt ip address gt mask lt admin state gt ip address The IP address assigned to the interface Avaya C460 Reference Guide 43 Chapter 2 Avaya C460 CLI Commands mask Mask for the associated IP subnet admin state The administration status either Up or Down Example To assign the IP address 192 168 22 33 with mask 255 255 255 0 to the interface marketing Router 1 config if marketing ip address 192 168 22 33 255 255 255 0 Done ip admin state User level read write admin O You can only access this command in interface mode Type interface name at the command prompt to enter interface mode Use the admin state command to set the administrative state of an IP interface The default state is up The syntax for this command is ip admin state lt up down gt up down Administrative state of the interface up active down inactive Example Router 1 config if marketing ip admin state up ip bootp dhcp network User level read write admin O You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip bootp dhcp network command to select the network from which the bootp dhcp server shall allocate an address You only need to run this command is required only when there are multiple interfaces over t
39. all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 set port disable 4 1 Port 4 1 disabled set port dot1x initialize User level admin Use the set port dotix initialize command to initialize port dotlx The syntax for this command is set port dotix initialize lt module port gt module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 super set port dotix initialize 2 3 port 1 2 dotix was initialized Avaya C460 Reference Guide 101 Chapter 2 Avaya C460 CLI Commands set port dot1x max req User level admin Use the set port dotix max req command to set the maximal number of times the port tries to retransmit requests to the Authenticated Station before the session is terminated The syntax for this command is set port dotlx max req lt module port gt count module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 count Number of attempts 1 to 10 Example C460 1 super set port dotix max req 1 2 5 set port dot1x port control User level admin Use the set port dotix port control command to set the dot1x parameter per port The synt
40. appropriate license before you can set the device mode to Router Avaya C460 Reference Guide 83 Chapter 2 Avaya C460 CLI Commands set device mode Layer 3 User level read write admin Use the set device mode command to change the basic mode of operation of the C460 switch between Router and Layer 2 modes The syntax for this command is set device mode lt mode gt mode Router Layer2 Example Router 1 set device mode Layer2 This command will RESET the device Reset do you want to continue Y N y set dot1x max req User level supervisor Use the set dot1x max req command to set maximum number of times the port tries to retransmit requests to the Authenticated Station before the session is terminated The syntax for this command is set dotix max req count count Number of attempts 1 to 10 Example C460 1 super set dotix max req 3 set dot1x quiet period User level supervisor Use the set dotix quiet period command to set the minimal time between authentication attempts The syntax for this command is set dotix quiet period lt Seconds gt Seconds Number of seconds 0 to 65535 84 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 super set dotix quiet period 90 Done set dot1x re authperiod User level supervisor Use the set dotix re authperiod command to set the id
41. ck ke port 5 11 configuration okckckckckckckckckck kckckckck ok Port type Tranceiver Not Present 4 Link status no link STA status Disabled fp kK KR ckck kkk Kk kkk k ck ck ck k ck ck k ck ckckck AS set port disable 5 11 set port auto negotiation flowcontrol advertisement 5 11 no flowcontrol set port negotiation 5 11 enable type q to quit or space key to continue set port level 5 11 O0 set trunk 5 11 off set port vlan 1 5 11 set port name 5 11 NO NAME set port trap 5 11 enable set port classification 5 11 valuable set port enable 5 11 Avaya C460 Reference Guide 181 Chapter 2 Avaya C460 CLI Commands 1 RR RK KK ck kc k kc kc kc KKK port 5 12 configuration occ ck ck ckckckckckck ck ck kckckck Port type Tranceiver Not Present 4 Link status no link 4 STA status Disabled p FER RRR kk kc Ck CkcCkCkCkCkCkCkCKCKCk Ck Ck k k k k k k k k k Kk k KK KK k k KK KK Ck Ck KK k k k k k k KK ck ck KKK set port disable 5 12 set port auto negotiation flowcontrol advertisement 5 12 no flowcontrol set port negotiation 5 12 enable set port level 5 12 0 set trunk 5 12 off set port vlan 1 5 12 set port name 5 12 NO NAME set port trap 5 12 enable set port classification 5 12 valuable set port enable 5 12 E Set port redundancy E set port redundancy enable set port redundancy intervals 1 none E Set vlan table management parameters E set port vlan binding mode 5 1 static set po
42. delivered on the port Fault Invalid PD connected Critical High Low User level read only read write admin Use the show powerinline budget command to display the PoE budget distribution for modules in the switch The budget assigned for the module includes power for PoE ports and power required for module basic PoE operation Avaya C460 Reference Guide 199 Chapter 2 Avaya C460 CLI Commands The syntax for this command is show powerinline budget Example C460 1 gt show powerinline budget Slot Module Type Budget Demand 3 MA612ML G N A N A 4 M4648ML T 2G PWR 720W 12W 5 MA648ML T PWR 720W 156W 6 M4648ML T 2G N A N A show ppp authentication User level read only read write admin Use the show ppp authentication command to display the authentication method used for PPP sessions The syntax for this command is show ppp authentication Example C460 1 gt show ppp authentication PPP Authentication Parameters Incoming CHAP show ppp baud rate User level read only read write admin Use the show ppp baud rate command to display the ppp baud rate The syntax for this command is show ppp baud rate Example C460 1 gt show ppp baud rate PPP baud rate is 38400 200 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show ppp configuration User level read only read write admin Use the show ppp configuration com
43. dotix system auth control disabled set dot1x system auth control enable User level supervisor Use the set dotix system auth control enable command to globally enable the PBNAC 802 1x feature The syntax for this command is set dotlx system auth control enable Examples e When a RADIUS server is defined C460 1 super set dotix system auth control enable dotix system auth control enabled 86 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands e When a RADIUS server is not defined C460 1 super set dotlx system auth control enable Warning Authentication server RADIUS is disabled not exist and so no authentication can be made dotix system auth control enabled set dot1x tx period User level supervisor Use the set dotix tx period command to set the time interval between attempts to access the Authenticated Station The syntax for this command is Example set dotix tx period Seconds Seconds Interval in seconds C460 1 super set dotix tx period 90 Done set icmp redirect User level read write admin Use the set icmp redirect CLI command to accept or reject incoming ICMP redirect requests The syntax for this command is set icmp redirect accept reject Accept Accept inoming ICMP redirect requests Reject Reject incoming ICMP redirect requests Example C460 1 set icmp redirect accept Done
44. for a reply from the Authentication Server before the session is terminated 104 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is set port dotlx server timeout module port seconds module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 seconds Timeout in seconds 0 to 65535 Example C460 1 super set port dotlx server timeout 1 2 400 set port dot1x supp timeout User level admin Use the set port dotix supp timeout command to set the time for the port to wait for a reply from the Authentication Server before the session is terminated The syntax for this command is set port dotix supp timeout module port seconds module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 seconds Timeout in seconds 0 to 65535 Example C460 1 super set port dotix supp timeout 1 2 400 set port dot1x tx period User level admin Use the set port dotix tx period command to set the time interval between attempts to access the Authenticated Station The syntax for this command is set port dotix tx period module port seconds module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports
45. get the default entity of the specific module switch Layer 2 entity of the module router Routing entity Avaya C460 Reference Guide 79 Chapter 2 Avaya C460 CLI Commands Example C460 1 gt session router Router 1 super The security level stays the same when you use the session command set allowed managers User level read write admin Use the set allowed managers command to enables or disable the Allowed Managers feature When this feature is enabled only those stations whose IP addresses are listed in the Allowed Managers table can access the device over Telnet SNMP or HTTP The syntax for this command is set allowed managers enabled disabled Example C460 1 super set allowed managers enabled Managers are enabled set allowed managers ip User level read write admin Use the set allowed manager ip command to add or remove an IP address from the Allowed Managers table The Allowed Managers table can contain up to twenty IP addresses The syntax for this command is set allowed managers ip add delete IP address add Add specified IP address to the Allowed Managers table delete Deletes specified IP address from the Allowed Managers table IP address IP address to be added or remove 80 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 super set allowed managers ip add 149 49 32 134 Ip was
46. is show ip access lists lt policy list number gt policy list number The policy list number integer from 100 to 199 156 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show ip access lists ip access list 100 10 deny and notify tcp 192 168 55 0 0 0 0 255 range 5000 6000 any range 7000 8000 ip access list 100 30 deny udp any any optional ip access list 100 35 deny ip any any ip access list 100 55 fwd7 tcp host 192 168 3 4 eq 33333 host 10 6 7 8 default action for list 100 is permit show ip access list summary User level user privileged supervisor Use the show ip access list summary command to display a summary of policy lists The syntax for this command is show ip access list summary Example C460 1 gt show ip access list summary The policy lists summary default List 0 show ip arp User level read only read write admin Use the show ip arpcommand to display the Address Resolution Protocol ARP cache The syntax for this command is show ip arp if name vlan ip addr ip mask static if name Interface name string up to 32 chars Avaya C460 Reference Guide 157 Chapter 2 Avaya C460 CLI Commands vlan VLAN NAME string up to 16 chars or VLAN ID number ip addr The IP address of the station s ip mask The ip mask of the routes static Display static ip ARP informati
47. must enclose the entire name in quotation marks for example new york Avaya C460 Reference Guide 35 Chapter 2 Avaya C460 CLI Commands interface User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the interface command to create and enter the Interface Configuration Mode Use the no interface command to delete a specific IP interface The syntax for this command is no interface lt interface name gt interface name String up to 32 characters Example C460 1 configure interface marketing Done Router 1 config if marketing If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york 36 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands ip access default action User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access default action command to set the default action for a specific policy list The syntax for this command is ip access default action lt policy list number gt lt default action gt lt policy list number gt integer 100 to 149 lt default action gt default action
48. parameters are trap log logAndTrap none description A user description of this event owner Owner name string Example C460 1 rmon event 1054 logAndTrap description event for monitoring gregory s computer owner gregory event 1054 was created successfully User level read write admin Use the rmon history command to create an RMON history entry The syntax for this command is rmon history lt history index gt lt module gt lt port gt interval lt interval gt buckets lt number of buckets gt owner lt owner name gt history_index This is the history index number of this entry it is advisable to use the same interface number as your history index number module port The switch number the port number interval The interval between two samples number of The number of buckets defined buckets 76 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands owner name The owner name string Example C460 1 rmon history 1026 1026 3 2 30 buckets 20 owner amir history 1026 was created successfully If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york rmon2 protocol dir User level privileged supervisor O If you are at the privileged level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the rmon
49. point status User level read only read write admin Use the show port point to point status command to show the port s point to point admin and operational RSTP status The syntax for this command is show port point to point status lt module port gt module Number of the module 3 6 If you do not specify a number all Optional modules are shown port Number of the port on the module If you do not specify a Optional number all ports on the specified module are shown Example C460 1 gt show port point to point status Port point to point admin state point to point oper state 1 1 auto point to point connection 1 2 auto point to point connection 1 3 auto point to point connection 1 4 auto point to point connection 1 5 auto point to point connection 1 6 auto point to point connection 1 7 auto point to point connection 196 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show port redundancy User level read only read write admin Use the show port redundancy command to display information about software port redundancy schemes defined for the switch The syntax for this command is show port redundancy Example Redundancy Name gregory amir lior arie C460 1 gt show port redundancy Minimum Time between Switchovers 1 Switchback interval 3 Primary Port Secondary Port Status 3 48 3 47 secondary 3 46 3 45 secondary 3471 3 2 primary 3 34 3 33 secondary
50. retrieve E mail from a mail server Most E mail applications use the POP protocol although some can use the newer IMAP Internet Message Access Protocol POP3 unlike earlier versions can be used with or without SMTP Port A physical port is a connecting component that allows a microprocessor to communicate with a compatible peripheral A port is identified by a port number 250 Avaya C460 Reference Guide Glossary Protocol A set of rules and conventions that governs how devices exchange data especially across a network Low level protocols define the electrical and physical standards to be observed bit and byte ordering the transmission error detection and correction of the bit stream High level protocols deal with data formatting including message syntax terminal to computer dialogue character sets message sequencing etc Protocol Stack A layered set of protocols which work together to provide a set of network functions Each intermediate layer uses the layer below it to provide a service to the layer above PSTN Public Switched Telephone Network The collection of interconnected systems operated by the various telephone companies and administrations around the world PVC Permanent Virtual Circuit A permanent virtual connection established by the network management between an origin and a destination QoS Quality of Service A measure of performance for a transmission system that reflects the s
51. send 5 1 off Port 5 1 flow control send administration status set to off port will send flowcontrol to far end Avaya C460 Reference Guide 109 Chapter 2 Avaya C460 CLI Commands set port level User level read write admin Use the set port level command to set the priority level of a port or range of ports on the switching bus Packets traveling through a port set at normal priority should be served only after packets traveling through a port set at high priority are served The syntax for this command is set port level lt module gt lt port gt value module Number of the module 3 6 port Number of the port on the module If you do not specify a number the level for all the ports on the module is set You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 value Priority level 0 7 Example C460 1 set port level 3 1 5 Port 3 1 level set to 5 set port mirror User level read write admin Use the set port mirror command to define a port mirroring pair in the switch The syntax for this command is set port mirror source port lt module gt lt port gt mirror port lt module gt lt port gt direction lt direction gt module Number of the module 3 6 port Number of the port on the module always Keyword to activate the port mirroring entry disable Keyword to change the status of the port mirroring entry to
52. step reris iners 114 Avaya C460 Reference Guide v Contents set port redundancy on off sess 115 set port redundancy intervals sss 115 SET POL SPANKS eec up egent dere tede 116 set port spantree cost oo eeccccceecceescenecsetecsenecsetecsensesetsesensesenecssneesensesees 117 set port spantree force protocol migration sees 117 set port spantree priority sse eene eene 118 Set iport Speed x iiber n e e di a teet detente 118 Set portstatic vlan eri tede t endende 119 A d ee e eed 119 Set port ad et elt utet eer ete tes 120 set port vlan binding mode 7 7 eee 121 set power redundancy miret sese eee eene nnns 121 set powerinline budget oo eee esses ees 122 set ppp authentication incoming sees eee 122 Set ppp bauid rate edente ei eie 123 set ppp chap sectet cus iei e tube eee teet tee ne 123 set ppp incoming timeout sss e eene 123 qset radius authentication enable disable sssss 124 set radius authentication retry number 7 7 e 124 set radius authentication retry time sssssssssseeeeeee 125 set radius authentication secret ccccccccccesseeecssessecssessecsscessesscssseeeseeees 125 set radius authentication server sse 125 set radius authentication udp port cococenoncnnnncnononnnnrarnennnnnananonnararannnnnnnnass 126 Set slot power admtin ne tnb ter
53. to be blocked in case two ports with the same costs cause a loop The syntax for this command is set port spantree priority module port value module port Module number port number value Number representing the priority of the port The priority level is from 0 to 255 with 0 indicating high priority and 255 indicating low priority A port with a lower priority will be blocked Example C460 1 set port spantree priority 3 4 128 port 3 4 spantree priority is 128 set port speed User level read write admin Use the set port speed command to configure the speed of a port or range of ports In auto negotiation mode the port s speed is determined by auto negotiation An error message is generated if you attempt to set the speed when auto negotiation is enabled The syntax for this command is set port speed lt module gt lt port gt lt 10MB 100MB 1GB gt module Number of the module 3 6 118 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands port Number of the port on the module If you do not specify a number the speed is set for all the ports on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example To configure port 1 on module 4 to 100 Mbps C460 1 set port speed 4 1 100MB Port 4 1 speed set to 100Mbps set port static vlan User level read write admin U
54. unicast cache iirinn ni ee oE E E E EEEE 167 show ip unicast cache networks sss 168 show ip unicast cache networks detailed sss 169 show ip unicast cache nextHop s sss 169 show ip unicast cache summary ssssssssseeee ee 170 show ip VER eene teret hiec ette mite gr etn 170 show ip vrrp detail 2 2 tnnt tat aet iege 171 show J23contie 3o A en be 173 Show licenses A A E E an Ei 183 show logott ettet ete ie E eerie 183 NA tereti eel te tle Lire teneri bereit 183 show mac aging time ssssssseeeeeee eee e eene eene 184 SHOW module eet e DN te NEN EM ep gies 185 show outbarnd ze mtcr e user eve de teo de patos em aedes 186 show policy type ciiin eee nete e tee itg 186 SHOW PORE ie e e e m e ee eH RR RETE 187 show port auto negotiation flowcontrol advertisement 188 show portchiannel eene tte eter ee iter s 188 show port classification sse eee enn 190 SHOW port MOCK x ssc cete te de tme e teet 191 show port dotlx statistics sssssssssssseeseenerereene e 193 show port edge state incidan tee tnter iens 194 show port flowcontrol sssssseeeeee eene eene nnns 194 shoW portTtror ione ta ede eene mae drea 195 show port point to point status cocncononononnnoncnonanernrnnnonnnnnnnnrnnrarannnnnnnaso 196 show port redundancy sss 197 Show p rt trap cite i ueni atlas Ed tesis 197 show port
55. 0 ping Layer 3 71 R redistribute 72 reset 73 rmon2 protocol dir 77 rmon2 protocol dist 77 router ospf 78 router rip 78 router vrrp 79 S session 79 set boot bank 223 set device mode 83 84 set logout 94 set slot power 126 set system contact 134 set system location 135 set system name 135 set welcome message 140 show access lists 140 show boot bank 223 show copy status 148 show device mode 150 show environment fans 151 show erase status 153 show event log 153 show ip access group 155 show ip access list dscp 156 show ip access lists 156 238 Avaya C460 Reference Guide Layer 3 CLI Commands show ip access list summary 157 traceroute 228 show ip arp 157 tree 228 show ip icmp 158 V show ip interface 159 validate group 230 231 show ip ospf 160 show ip ospf database 161 show ip ospf interface 161 show ip ospf neighbor 162 show ip protocols 162 show ip reverse arp 163 show ip route 163 show ip route best match 164 show ip route static 164 show ip route summary 165 show ip unicast cache 167 show ip unicast cache networks 168 show ip unicast cache networks detailed 169 show ip unicast cache summary 170 show ip unicast nextHop 169 show ip vrrp 170 show ip vrrp detail 171 show logout 183 show module 185 show rmon2 dscp stats 205 show running config 209 show snmp 211 show snmp retries 212 show snmp timeout 208 212 show spv 208 214 show startup config 216 show system 217 show sys
56. 0 0 Avaya C460 Reference Guide 203 Chapter 2 Avaya C460 CLI Commands show rmon history User level read only read write admin Use the show rmon history command to display the most recent RMON history log for a given History Index The history index is defined using the rmon history command on 76 or using an RMON management tool The syntax for this command is show rmon history History Index gt History Index History index defined using rmon history command or RMON management tool Example C460 1 gt show rmon history 1026 history Entry 1026 is active owned by amir Monitors ifEntry 1 1026 every 30 seconds Requested of time intervals ie buckets is 20 Granted of time intervals ie buckets is 20 Sample 1 began measuring at 2 53 9 Received 62545 octets 642 packets 391 broadcast and 145 multicast packets 0 undersize and 0 oversize packets 0 fragments and 0 jabbers 0 CRC alignment errors and 0 collisions of dropped packet events due to a lack of resources 0 Network utilization is estimated at 0 show rmon statistics User level read only read write admin Use the show rmon statistics command to show the Received Packet RMON statistics counters for a certain interface number according to the MIB 2 interface table numbering scheme The syntax for this command is show rmon statistics lt module port gt module port Range of ports 204 Avaya
57. 0 14 set snmp retries 10 SNMP retries is set to 10 set snmp timeout User level read write admin Use the set snmp timeout command to set the SNMP timeout in seconds This command is useful for access using the C460 Manager The syntax for this command is set snmp timeout lt number gt number Timeout in seconds Example C460 1 set snmp timeout 2000 the SNMP Timeout is set to 2000 set snmp trap User level read write admin Use the set snmp trap command to add an entry into the SNMP trap receiver table and to enable or disable the different SNMP traps for a specific receiver First add the rcvr_addr and then enable disable the different traps for it The syntax for this command is set snmp trap lt rcvr_addr gt set snmp trap lt rcvr_addr gt enable disable all config fault enable Activate SNMP traps disable Deactivate SNMP traps all Optional Specify all trap types config Optional Specify the ConfigChange trap from the TRAP MIB fault Optional Specify the Fault trap from the TRAP MIB rcvr addr IP address or IP alias of the system to receive SNMP traps Avaya C460 Reference Guide 129 Chapter 2 Avaya C460 CLI Commands Example To enable SNMP ConfigChange traps to a specific manager C460 1f set snmp trap 192 168 173 42 enable config SNMP config change traps enabled Example To enable all traps to a specific manager C460 1 set snmp trap 192 168 1
58. 1 super router ospf Done router rip User level read write admin If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the router rip command to configure the Routing Information Protocol RIP Use the no router rip command to disable RIP The default state is disabled The syntax for this command is no router rip Example 78 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands router vrrp session To enable the RIP protocol C460 1 configure router rip Done User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the command to enable VRRP routing globally Use the no router vrrp command to disable VRRP routing The syntax for this command is no router vrrp Example C460 1 configure router vrrp Done User level read only read write admin Displays existing sessions or to opens a session with a specific Supervisor Module in the chassis The syntax for this command is session module_number gt switch router module The Supervisor module number 1 to 2 switch router The entity to which you want to open a Optional session Ifyou do not specify this parameter you will
59. 192 168 66 23 255 14 MASTER 00 00 00 ab 2 192 168 66 24 100 1 BACKUP 00 00 00 170 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show ip vrrp detail User level read only read write admin Use the show ip vrrp detail command to display full VRRP related information The syntax for this command is show ip vrrp detail detail Show full detail information Avaya C460 Reference Guide 171 Chapter 2 Avaya C460 CLI Commands Example Router 1 gt show ip vrrp detail VRRP is globally enabled Virtual Router on VLAN 1 Router id 1 State MASTER Priority 255 Advertisement Interval 1 Last State Change 00 00 00 Override Address Ownership Rule No Authentication Type None Authentication Key ne Master IP Address 192 168 66 23 Has 1 IP addresses IP addresses 192 168 66 23 Primary IP Address 192 168 66 23 Primary IP Address was chosen by default Preemption Mode enabled of times Master 2 of received Advertisements 0 of transmitted Advertisements 20 of received Advertisements with Security Violations 0 Virtual Router on VLAN 1 Router id 2 State BACKUP Priority 100 Advertisement Interval 1 Last State Change 00 00 00 Override Address Ownership Rule No Authentication Type None Authentication Key n Master IP Address 0 0 0 0 Has 1 IP addresses IP addresses 192 168 66 24 Primary IP Address 192 168 66 23 Primary IP Address was chosen by default Preem
60. 2 Avaya C460 CLI Commands show allowed managers table User level read only read write admin Use the show allowed managers table to display the list of the twenty possible allowed managers IP addresses The syntax for this command is show allowed managers table Example Q 0 Ov Ui i 0 IN S LA p ppp pA pA LA oO Lono 0 PF2n Oo N H 149 Not Not Not Not Not Not Not Not Not Not Not Not Not Not Not Not Not Not Not C460 1 super show allowed managers table 49 32 134 Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used Used 142 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show arp aging interval User level read only read write admin Use the show arp aging interval command to display the ARP table aging interval for gateway entries The syntax for this command is show arp aging interval Example C460 1 gt show arp aging interval ARP table aging interval for gateways was set to 10 minutes show arp tx interval User level read only read write admin Use the show arp tx interval command to display the keep alive frames transmission interval The syntax for this command is show arp tx interval Example C460 1 gt show arp tx interval ARP tx interval for inband interface is set to 5 seconds ARP tx interval for outband interfac
61. 2 Avaya C460 CLI Commands show startup config User level read only read write admin Use the show startup config command to display the router startup configuration Example show startup config Example Router 1 gt show startup config Router 1 gt Avaya Inc C460ML Multi layer Switch Router configuration version 2 0 2 ip access list name 100 list 100 ip access list owner 100 egotlieb 135 64 102 64 ip access list 100 1 permit ip any any ip access list 100 2 fwd3 udp any eq 68 any eq 67 set vlan 2 name vlan2 no rmon2 protocol dir TCP 20 no rmon2 protocol dir TCP 23 no rmon2 protocol dir TCP 25 no rmon2 protocol dir TCP 80 no rmon2 protocol dir TCP 110 no rmon2 protocol dir UDP 161 no rmon2 protocol dir UDP 162 rmon2 protocol dir TCP 1111 1111 TCP rmon2 protocol dir TCP 2222 2222 TCP interface 11 ip vlan name Default ip address 11 11 11 1 255 255 255 0 type q to quit or space key to continue interface 12 ip vlan name vlan2 ip address 12 12 12 1 255 255 255 0 interface 78 ip vlan name Default ip address 149 49 78 71 255 255 255 0 ip default gateway 149 49 78 1 1 low 216 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show system User level read only read write admin Use the show system command to display the uptime system name location contact person and MAC addresses The s
62. 2 protocol dir to add a protocol to the protocol directory Use the no rmon protocol dir command to remove a protocol from the protocol directory The syntax for this command is rmon2 protocol dir UDP TCP Port gt lt description gt lt owner gt Example Router 14 rmon2 protocol dir UDP 345 Router 1 rmon2 protocol dir UDP 345 my description Router 14 rmon2 protocol dir UDP 345 description I am the owner Done If you wish to enter a name which includes spaces you must enclose the entire name in quotation marks for example new york rmon2 protocol dist User level privileged supervisor O If you are at the privileged level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the rmon2 protocol dist to enable the RMON Protocol Distribution Avaya C460 Reference Guide 77 Chapter 2 Avaya C460 CLI Commands router ospf application Use the no rmon2 protocol dist command to disable the application The syntax for this command is no rmon2 protocol dist Example Router 14 rmon2 protocol dist Done User level read write admin Use the router ospf command to enable the OSPF protocol on the system Use the no router ospf command to disable the OSPF one the system The default is disabled The syntax for this command is no router ospf Example Router
63. 3 on module 4 mode no flowcontrol asym tx only sym only or sym and asym rx Example C460 1 gt show port auto negotiation flowcontrol advertisement 4 49 Port 4 49 pause capabilities was set show port channel User level read only read write admin Use the show port channel command to display Link Aggregation Group LAG information for a specific switch or port The syntax for this command is show port channel lt module gt lt port gt info module Number of the module 3 6 If you do not specify a number Optional the modules on all the switch are shown port Number of the port on the module If you do not specify a Optional number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 188 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands info Displays full information on the port Example C460 1 gt show port channel Port Channel Status Channel Name and Id 3 1 off 3 2 off 3 3 on serverl 3 4 on serverl 3 13 off C460 1 gt show port channel 3 3 info Port Speed Duplex Vlan Port Trunk Vlan Priority status Binding 3 3 10 half 1 0 off static Avaya C460 Reference Guide 189 Chapter 2 Avaya C460 CLI Commands show port classification User level read write admin Use the show port classification command to display a port s classification
64. 4 subnet mask is 255 255 255 0 Broadcast address is 10 49 54 255 Directed broadcast forwarding is disabled Proxy ARP is disabled baba is administratively down On vlan v2 Internet address is 192 168 0 14 subnet mask is 255 255 0 0 Broadcast address is 192 168 255 255 Directed broadcast forwarding is disabled Proxy ARP is disabled If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york Avaya C460 Reference Guide 159 Chapter 2 Avaya C460 CLI Commands show ip interface brief show ip ospf User level read only read write admin Use the show ip interface brief command to display brief information for an IP interface The syntax for this command is show ip interface brief lt interface gt lt vlan gt lt IP addr gt interface The name of the interface whose information you want to display a string of up to 32 characters vlan The name or ID of the VLAN over which there are interfaces you want to display a string of up to 32 characters IP addr The IP address of the interface whose information you want to display Example Router 1 show ip interface brief Showing 1 Interfaces Interface Address Mask Status net 149 49 54 56 255 255 255 0 up User level read only read write admin Use the show ip opsf command to displays general information about OSPF routing
65. 4 192 168 1 1 destination 0 0 0 0 mask 255 255 255 0 gateway 192 168 1 1 done Avaya C460 Reference Guide 93 Chapter 2 Avaya C460 CLI Commands set license User level read write admin Use the set license command to activate a licensed feature on a specific C460 chassis For a full description of the Feature License and the installation procedure please refer to the Installation Guide provided with the Feature License The syntax for this command is set license license featureName license The license number featureName The name of the feature currently either smon or routing The default feature is smon Example C460 1 set license 026 9b8 216 908 dea f 4d layer 3 Layer 3 Features had been enabled on this chassis set logout User level read write admin Use the set logout command to set the time in minutes until the system automatically disconnects an idle session The syntax for this command is set logout timeout in minutes timeout in Time until the system automatically disconnects an idle minutes session Setting the value to 0 disables the automatic disconnection of idle sessions The default value is 15 minutes 94 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example To set the time until the system disconnects an idle session automatically to 20 minutes C460 1 set logout 20 Sessions will be automatically logged out after 20 minutes of idle time
66. 5 to 13 on module 4 Avaya C460 Reference Guide 105 Chapter 2 Avaya C460 CLI Commands seconds Time interval in seconds 0 65535 Example C460 1 super set port dotix quiet period 1 2 5000 set port duplex User level read write admin Use the set port duplex command to configure the duplex type of an Ethernet or Fast Ethernet port or range of ports You can configure Ethernet and Fast Ethernet interfaces to either full duplex or half duplex The duplex status of a port in auto negotiation mode is determined by auto negotiation An error message is generated if you attempt to set the transmission type of auto negotiation Fast Ethernet ports to half or full duplex mode The syntax for this command is set port duplex lt module gt lt port gt value module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the module If you do not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 value full set full duplex transmission e half set half duplex transmission Example To set port 1 on module 4 to full duplex C460 1 set port duplex 4 1 full Port 4 1 set to full duplex set port edge admin state User level read write admin Use the set port edge admin state command to set the port a
67. 7 ip rip split horizon 58 ip route 59 ip routing 59 ip routing mode 60 ip simulate 61 ip vlan 61 ip vlan name 61 Avaya C460 Reference Guide 237 Layer 3 CLI Commands ip vrrp 62 ip vrrp address 62 ip vrrp auth key 63 ip vrrp override addr owner 63 ip virp preempt 64 ip vrrp primary 64 ip vrrp priority 65 ip vrrp timer 66 N network 67 network RIP 67 no area 13 no arp 14 no arp timeout 14 no default metric 30 31 no icmp error 48 no interface 36 no ip access list 38 no ip access group 37 no ip bootp dhcp 45 no ip bootp dhcp network 44 no ip bootp dhep server 46 no ip default 47 no ip directed broadcast 47 no ip max arp entries 48 no ip max route entries 49 no ip netbios rebroadcast 49 no ip netmask format 50 no ip ospf authentication key 51 no ip ospf cost 51 no ip ospf hello interval 52 no ip ospf priority 53 no ip ospf router id 53 no ip poison reverse 56 no ip proxy arp 54 no ip redirect 54 no ip rip authentication 55 no ip rip authentication key 55 no ip rip split horizon 58 no ip route 59 no ip routing 60 no ip vlan 61 no ip vlan name 61 no ip vrrp 62 no ip vrrp address 62 no ip vrrp auth key 63 no ip vrrp override addr owner 63 no ip vrrp priority 65 no ip vrrp timer 66 no network 67 no ospf dead interval 52 no passive interface 70 no redistribute 72 no router ospf 78 no router rip 78 no router vrrp 79 no timers spf 227 P passive interface 7
68. 70 ppp disabled N A 0 0 0 0 0 0 0 0 outband enabled N A 135 64 200 105 255 255 255 255 show ip access group User level privileged supervisor Use the show ip access group command to display the active policy list number The syntax for this command is show ip access group Example access group 101 C460 1 show ip access group Avaya C460 Reference Guide 155 Chapter 2 Avaya C460 CLI Commands show ip access list dscp User level user privileged supervisor Use the show ip access list dscp command to display the DSCP to CoS map of a policy list The syntax for this command is show ip access list dscp lt policy list number gt policy A valid id number for a policy list currently defined for the module list 100 199 0 default list number dscp dscp entry 0 63 Example C460 1 gt show ip access list dscp 101 Trust configuration is trust cos DSCP Action Precedence Name 0 fwdO mandatory DSCP 0 1 fwd0 mandatory DSCP 1 2 fwd0 mandatory DSCP 2 3 fwdo mandatory DSCP 3 4 fwd0 mandatory DSCP 4 5 fwdO mandatory DSCP 5 6 fwdO mandatory DSCP 6 7 fwd0 mandatory DSCP 7 8 fwd1 mandatory DSCP 8 9 fwd1 mandatory DSCP 9 10 fwd1 mandatory DSCP 10 11 fwdi mandatory DSCP 11 show ip access lists User level read only read write admin Usethe show ip access lists command to display all the current policy lists The syntax for this command
69. 73 42 enable all SNMP all traps enabled Example To disable SNMP config traps to a specific manager C460 14 set snmp trap 192 168 173 42 disable config SNMP config traps disabled Example To add an entry in the SNMP trap receiver table with default C460 14 set snmp trap 192 168 173 42 SNMP trap receiver added set snmp trap auth User level read write admin Use the set snmp trap auth command to enables or disable the sending of SNMP traps upon SNMP authentication failure The syntax for this command is set snmp trap enable disable auth Example C460 1f set snmp trap enable auth Authentication trap enabled 130 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set spantree default path cost User level privileged supervisor Use the set spantree default path cost command to set the version of the spanning tree default path costs that are to be used by this bridge The syntax for this command is set spantr default path cost lt path cost gt path cost common spanning tree compatible with IEEE802 1D standard e rapid spanning tree compatible with IEEE802 1W standard Example C460 1 set spantree default path cost rapid spanning tree Spanning tree default path costs is set to rapid spanning tree set spantree enable disable User level read write admin Usethe set spantree command to enable or disable the spanning tree
70. 8 49 1 User level read write admin O You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode Use the ip proxy arp command to enables proxy ARP on an interface Use the no ip proxy arp command to disable proxy ARP on an interface The syntax for this command is no ip proxy arp Example To disable proxy ARP on interface marketing Router 1 config if marketing no ip proxy arp User level read write admin You can only access this command in interface mode Type interface name at the command prompt to enter interface mode if necessary Use the ip redirects command to enables the sending of redirect messages on the interface Use the no ip redirects command to disable the redirect messages By default sending of redirect messages on the interface is enabled The syntax for this command is no ip redirects Example Router 1 config if marketing ip redirects ip rip authentication key User level read write admin You can only access this command in interface mode 54 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Type interface name at the command prompt to enter interface mode if necessary Use the ip rip authentication key command to set the authentication string used on the interface Use the no ip rip authentication key command to clear the password The syntax
71. 83 Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show mac aging mac aging application is disabled show mac aging time User level user privileged supervisor Use the show mac aging time command to display the MAC aging time in minutes The syntax for this command is show mac aging time Example C460 1 gt show mac aging time MAC aging time is 5 min O The displayed value is the aging time lower bound The actual aging time can be up to 2 minutes longer 184 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show module User level read only read write admin Use the show module command to display module status and information The syntax for this command is show module Example C460 1 gt show module Mod Type C S S N Status 0 C460 CH 1 0 0000008 N A 1 M460ML SPV L O 0000003 Active 2 M460ML SPV 1 0 0000017 Standby 3 M4612ML G L 0 0000004 Normal 4 M4648ML T 2G PWR L O 0000016 Normal 5 M4648ML T PWR L O 0000029 Normal 6 M4648ML T 2G 1 0 0000797 Normal PSU1 MPS4610 AC Active PSU2 MPS4610 AC 1 0 0000011 Active PSU3 Empty Fan M460 FAN OK Output Fields Mod Module slot number Type Module type C S Hardware Configuration Symbol of the module S N Serial number of the module Status Status of the module or slot Supervisor Module Active Standby e Halted e Unknown Empty Avaya C460 Reference Guide 185 Chapter 2
72. Avaya C460 CLI Commands show outband I O Module Normal e Not enough power Power disabled Empty User level read only read write admin Use the show outband command to displays the Ethernet Console port status This command applies to the specific supervisor module where you execute it The syntax for this command is show outband Example C460 1 gt show outband Status Connected Auto negotiation Enable Duplex Half Duplex Speed 100 MBit sec show policy type User level read only read write admin Usethe show policy type command to show whether the module enforces the active policy list on all packets or only on routed packets for modules in device mode router The syntax for this command is show policy type Example Policy type is router Router 14 show policy type 186 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show port User level read only read write admin Use the show port command to display port status on I O modules The syntax for this command is show port lt module gt port module Optional port Optional Number of the module 3 6 If you do not specify a number the ports on all the modules are shown Number of the port on the module If you do not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example
73. B Example C460 1 set boot bank A boot bank is A set broadcast storm control User level read write admin Use the set broadcast storm control command to enable or disable broadcast storm control The syntax for this command is set broadcast storm control lt enable disable gt enable Enable broadcast storm control disable Disable broadcast storm control Example C460 1 set broadcast storm enable Done 82 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set broadcast storm control threshold User level read write admin Use the set broadcast storm control threshold command to set the broadcast storm control threshold The syntax for this command is set broadcast storm control threshold lt threshold gt threshold In pps packets per second from 10 to 144 000 pps The default value is 500 Example C460 1 set broadcast storm control threshold 1000 Done set device mode User level read write admin Use the set device mode command to set the switch mode Layer 2 or Router Layers 2 and 3 The syntax for this command is set device mode mode mode e Router switch operates at Layers 2 and 3 layer2 switch operates at Layer 2 Example C460 1 super set device mode Router This command will RESET the switch Reset do you want to continue Y N Done O You need to install the
74. Blank no value display the current length of the screen Number set the screen length Example C460 1 terminal length terminal length 25 auto detected C460 1 terminal length 40 C460 1 terminal length C460 1 gt terminal width 40 user configured terminal width User level read only read write admin Use the terminal width command to set the width of the terminal display in characters The syntax for this command is terminal width characters characters Blank no value display the current width of the screen e Number set the screen width Example C460 1 gt terminal width terminal width 80 auto detected C460 1 gt terminal width 60 C460 1 gt terminal width terminal width 60 user configured timers basic User level privileged supervisor Avaya C460 Reference Guide 225 Chapter 2 Avaya C460 CLI Commands O You can only access these commands in the Router RIP context Type router rip at the command prompt to enter the Router RIP context if necessary Use the timers basic command to configure the route timer Use the no timers basic command to restore the timers to their default values Example Router N configure router rip timers basic 30 180 The syntax for this command is timers basic lt update gt lt invalid gt update RIP update timer in seconds minimum 30 default 30 invalid RIP invalid ro
75. C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example 0 0 C460 1 gt show rmon statistics Statistics for switch is active owned by Monitor Monitors ifEntry 1 1026 which has Received 26375085 octets 222536 packets 154821 broadcast and 53909 undersize and 0 oversize packets fragments and 0 jabbers CRC alignment errors and 0 collisions of dropped packet events due to a lack of resources of packets received of length in octets 64 94530 65 127 85124 128 255 25896 256 511 10440 512 1023 6057 1024 1518 489 multicast packets 0 show rmon2 dscp stats User level read only read write admin Use the show rmon2 dscp stats command to display the DSCP distribution routed traffic only for the RMON2 application The syntax for this command is show rmon2 dscp stats Example Router 1 gt show rmon2 dscp stats DSCP Value Total Packets Total Octets Utilization 3 7620262 487696768 59 99 7 5080185 325131840 40 00 Total 12700447 812828608 99 99 Avaya C460 Reference Guide 205 Chapter 2 Avaya C460 CLI Commands show rmon2 protocol dir User level read only read write admin Use the show rmon2 protocol dir command to display the protocols in the TCP UDP protocols list The syntax for this command is show rmon2 protocol dir UDP TCP lt Port gt UDP UDP protocol TCP TCP protocol Port Port Example Rout
76. Commands set port flowcontrol User level read write admin Use the set port flowcontrol command to set the send receive mode for flow control frames IEEE 802 3x or proprietary for a full duplex port Each direction send or receive can be configured separately The syntax for this command is set port flowcontrol direction lt module port gt value direction e receive determines whether the port can receive administrative status from a remote device Available only for Gigabit Ethernet modules with negotiation set to off send determines whether the local port can send administrative status to a remote device Available only for Gigabit Ethernet modules with negotiation set to off e all send and receive symmetric flow control module Number of the module port Number of the port on the module value e off used with receive to turn off an attached device s ability Example to send flow control packets to a local port Used with send to turn off the local port s ability to send administrative status to a remote device on used with receive to require that a local port receive administrative status from a remote device Used with send the local port sends administrative status to a remote device C460 1 set port flowcontrol receive 5 1 on Port 5 1 flow control receive administration status set to on port will require far end to send flowcontrol C460 1 set port flowcontrol
77. Data Interface A set of ANSI protocols for sending digital data over fiber optic cable FDDI networks are token passing networks and support data rates of up to 100 Mbps FDDI networks are typically used as backbones for wide 244 Avaya C460 Reference Guide Glossary area networks FDX Full Duplex A circuit or device permitting simultaneous data transmission between sending and receiving stations For more information refer to Duplex Mode on page 244 Flow Control Avaya s devices use a proprietary form of flow control that enables one endpoint to inform another endpoint that it should refrain from sending additional packets The flow control mechanism avoids packet loss Flow control is used in Full Duplex Mode Fragment Ethernet packet shorter than 576 bits usually the result of a collision Frame A logical grouping of information sent as a Data Link Layer unit over a transmission medium The word Frame often refers to the header and trailer used for synchronization and error control that surround the user data contained in the unit FTP File Transfer Protocol An application protocol part of the TCP IP protocol stack used for transferring files between network nodes Full Duplex FDX A circuit or device permitting simultaneous data transmission between sending and receiving stations Duplex Mode on page 244 Half Duplex HDX A circuit or device permitting data transmission in only one directi
78. E HE E HE ERE ERE ERE RE E 4 Slot 4 is empty E E 174 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands HEFE FE AE FE HE HE FE HE FE FE EEE FE FE FE FE FE FHE EH EH FE FE HE FE FHE HE FE HE FE FE HE FE FE FE FE HE FHE HE HE HE HE FHE HE FHE HE HE EE EEE EEE FE HE HE HE EEE IOBLADE INFO EFE FE AE FE HE HE HE HE EE EH EEE EH FE FE FE FE FE FHE HE FE FE FE FE EE FE FE HE HE FHE HE FE HE HE HE HE FHE HE FE HE HE EEE HE FE HE FE HE HE HE EEE Slot 5 Blade type M4612ML G type q to quit or space key to continue l Blade Cs 0 1 I Serial 0000114 Number of ports 12 HEFE FEAE FE HE HE FE HE FE FE FE HE FE FE FE FE FE FE FE FHE FE FE FE FE FE HE FE FE FE FE FE FHE FE FE FE FE FHE HE FE FE FE HE HE FHE HE HE HE HE FHE HE FHE HE FE HE HE RIOR FHE HE FHE HE HE HE HEHE HE I IOBLADE INFO HEFE FE AE FE HE HE HE HE FE FE FE FE FE FE FE FE EEE EH FE FE FE FE FE FHE HE EE FE HE FE HE FE FHE HE FHE HE FE HE HE EE E HE FHE HE FHE HE HE HE HE FHE HE HE HE EEE Slot 6 is empty HEHE HE HE HE HE HE HE HE HE HE HE HE HE E HE HE FE HE HE FE HE HE FE HE E HE HE FE HE FE FE HE HE FE HE HE FE HE E HE HE HE HE HE HE HE HE HE HE HE HE HE FE HE HE HE HE HE FHE HE HE HE HE HE HE HE HE HH HE set spanning tree mode set spantree enable set spantree priority 32768 Set ARP to myself parameters l set arp tx interval inband 5 type q to quit or space key to continue set arp tx interval
79. LI Commands Example Router 1 show ip unicast cache Showing 6 Sessions IP Address NH MAC NH VLAN 92 168 1 29 2 2141 5 92 168 2 29 2241 5 92 1168 2 2 29 2 2 2 5 92 LOB 2 lt 3 29 2 2 3 5 92 168 2 4 29 2 2 4 5 92 168 2 5 29 2 2 5 5 show ip unicast cache networks User level read only read write admin Displays summary of networks handled by the hardware unicast cache database The syntax for this command is show ip unicast cache networks net addr net mask net addr The IP address of the network net mask The mask IP address Example Router 1 show ip unicast cache networks Showing 7 rows 5 networks Network Mask Next Hop s Total Hosts 10 0 0 0 16 10 2 0 2 996 71 0 0 0 16 0 0 0 0 1 130 0 0 0 8 192 168 0 130 1124 190 0 0 0 24 10 2 0 2 250 192 168 0 130 191 0 0 0 24 10 2 0 2 250 192 168 0 130 168 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show ip unicast cache networks detailed User level read only read write admin Use the show ip unicast cache networks detailed command to list the networks and hosts that are handled by the hardware unicast cache database The syntax for this command is show ip unicast cache networks detailed lt net addr gt lt net mask gt net addr net mask Example The IP address of the network The mask IP address 192 168 6 0 24 Showing 3 rows Router 1 gt show
80. P User Datagram Protocol Connectionless transport layer protocol in the TCP IP protocol stack UDP is a simple protocol that exchanges datagrams without acknowledgments or guaranteed delivery requiring that error processing and retransmission be handled by other protocols Unicast A single packet sent to a single network destination Virtual Connection A connection established between end users source and destination where packets are forwarded along the same path and bandwidth is not permanently allocated until it is used Virtual Path A group of virtual channels that can support multiple virtual circuits VSA Vendor Specific Attribute RADIUS supports attributes of which one the VSA supports vendor specific attributes This allows vendors to create custom RADIUS attributes Avaya C460 Reference Guide 255 Glossary 256 Avaya C460 Reference Guide
81. Reference Guide Avaya C460 MULTILAYER MODULAR SWITCH SOFTWARE VERSION 2 0 ome AVAYA avaya com 2003 Avaya Inc All rights reserved All trademarks identified by the or TM are registered trademarks or trademarks respectively of Avaya Inc All other trademarks are the property of their respective owners Document no 555 500 200 Contents Chapter 1 Using the C LI enit tette me epa e ete tie le e vu celu 1 GEI Architecture fcc eundo eee te cen eee cintas 1 Conventions Used inet reed eter eic Hes 2 CIELEelpzs niai eme tem ei tent itn ih iet 2 Command Line Prompt erect e tte 2 Navigation Cursor Movement and Shortcuts sss 4 Command tasca eiii eit nien aep epit iecit ni 4 Command Abbreviations eese eene eene enhn enne nnn enne 4 Universal Command Sisseneri htt iii do Theo teet egens 5 Retstatus command ar i ette enne iaa tette tenente 5 Tree co mmniand idealistas ibas 5 terminal width iei ede etta idend o EHE 6 terminal length eee RIOT epi een 6 CLE AT screen 225 eoe eain tesis eee e ede e EET TRE 7 Avaya C460 SESSIONS se icona ven uer nd eere rn id reb rra 8 Security levels ote nitet ete een eL RD s Lon de Eti tas 9 Entering the Supervisor Level sse 9 Entering the TL cintia a i rd ec 10 Entering the Technician Level sss 10 Getting Help csi lora behind n ides 10 Command diia a da ree d tee dent tun 10 Command Abbr
82. Reference Guide 1 Chapter 1 Using the CLI Conventions Used CLI Help Mandatory keywords are in the computer bold font Information displayed on screen is displayed in computer font Variables that you supply are in pointed brackets lt gt Optional keywords are in square brackets Alternative but mandatory keywords are grouped in braces and separated by a vertical bar Lists of parameters from which you should choose are enclosed in square brackets and separated by a vertical bar If you enter an alphanumeric string of two words or more enclose the string in inverted commas To display all commands available in a context type a question mark To display all commands starting with a certain string type the first few letters followed by a question mark To get help containing all commands parameters with their legal values as well as its syntax and an example type a question mark at the end of command or at the stage where it is unique or type help followed by the command Use the Tab key to complete an unambiguous command Command Line Prompt Four factors affect the command line prompt Host name of the CLI entity the host name is used as the prefix of the command prompt Module Number counting from the top and used as part of the prefix In this document the Module number in the prompt is generic and is represented by INT Security level used as the suffix of the prompt Refer t
83. The syntax for this command is Avaya C460 Reference Guide 69 Chapter 2 Avaya C460 CLI Commands nvram initialize switch all switch Resets all the switch information Layer 2 only all Resets all parameters including routing parameters in the switch Example C460 1 nvram initialize This command will restore factory defaults and can disconnect your telnet session Reset do you want to continue Y N y Connection closed by foreign host O The nvram initialize command does not alter the Active Standby status of the Supervisor modules passive interface User level read write admin O You can only access this command in Router OSPF mode Type router ospf atthe command prompt to enter Router OSPF mode if necessary Usethe passive interface command to allow interfaces to be flooded into the OSPF domain as OSPF routes and not external routes Usetheno passive interface command to disble the flooding O An interface becomes passive only if you use the network command to enable OSPF to run on the interface The syntax for this command is passive interface interface name net addr interface name Name of interface or IP address net addr Example Router 14 passive interface FastEthernet 1 10 70 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands ping User level read only read write admin Use the ping command to send ICMP echo request packe
84. VLAN ID The syntax for this command is set port vlan vlan num lt module gt lt port gt vlan num module port Number identifying the VLAN The module number Number of the port on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 120 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 set port vlan 2 3 5 VLAN 2 modified VLAN Mod Ports set port vlan binding mode User level read write admin Usetheset port vlan binding mode command to define the binding method used by ports The syntax for this command is set port vlan binding mode port list value port list Switches and ports to bundle format module port value static the port supports only the VLAN as configured per port e bind to configured the port supports the VLANs configured on the device bind to all the port support the whole range of VLANs on the device Example C460 1 set port vlan binding mode 5 5 9 static Set Port vlan binding method 5 5 Set Port vlan binding method 5 6 Set Port vlan binding method 5 7 Set Port vlan binding method 5 8 Set Port vlan binding method 5 9 HERMES set power redundancy User level read write admin Use the set power redundancy command to enable or disable PSU power supply redundancy Avaya C460 Reference Guide 121 Chapter 2 Av
85. Windows Router 14 copy startup config tftp c c460 startup cfg 149 49 100 41 Example for Unix C460 1 copy startup config tftp folder c460 startup cfg 149 49 100 41 copy tftp EW_archive User level read write admin Use the copy tftp EW archive command to download the C460 Manager application into the switch via TFTP O To use this command you need to have an active TFTP server and to create a file into which to download the data O If Avaya MultiService Network Manager is running you do not require an additional TFTP server The syntax for this command is copy tftp EW archive filename ip filename C460 Manager image file name full path ip The IP address of the host Example C460 1 copy tftp EW archive c 1C4601switchl cfg 192 168 49 10 copy tftp 12 config User level read write admin Use the copy tftp 12 config command to update the Layer 2 parameters in the current NVRAM running configuration from a file via TFTP O To use this command you need to have an active tftp server and to create a file into which to download the data O If Avaya MultiService Network Manager is running you do not require an additional TFTP server Avaya C460 Reference Guide 27 Chapter 2 Avaya C460 CLI Commands The syntax for this command is copy tftp 12 config lt filename gt lt ip gt filename file name including full path ip IP address of the host Example
86. access list lt policy list number gt lt access list index gt lt action gt lt protocol gt lt source ip gt lt source wildcard gt any host lt source ip gt lt operator gt port lt port lt destination ip gt lt destination wildcard gt any host destination ip operator port lt port gt established precedence lt access list number gt integer 100 to 149 0 is the default list lt access list index gt integer 1 to 254 lt command gt permit deny deny and notify fwd0 7 composite op name lt protocol gt ip tcp udp integer 1 to 255 lt source ip gt ip network lt source wildcard gt ip network wildcard lt operator gt eq It gt range lt port gt integer 1 to 65535 lt destination ip gt ip network lt destination wildcard gt ip network wildcard lt precedence gt mandatory optional 38 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 configure ip access list 101 23 deny ip any 1 2 0 0 0 0 255 255 ip access list cookie User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access list cookie command to set the list cookie for a specific policy list The syntax for this command is ip access list cookie lt policy list number gt lt
87. ached shown only on non root bridges Root Max Age Amount of time a BPDU packet should be considered valid Hello Time Number of times the root bridge sends BPDUs Bridge ID MAC ADDR Bridge MAC address used in the sent BPDUs Bridge ID Priority Bridge Priority Port Port number Port State Spanning tree port state disabled inactive not connected blocking listening learning forwarding bridging or type pvid inconsistent Cost Cost associated with the port Priority Priority associated with the port show spv User level read only read write admin Use the show spv command to display the following information about supervisor modules e Chassis MAC address e SPV status active standby halted e Indication whether the SPV s are synchronized Software version of the two image banks The syntax for this command is show spv 214 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show spv Chassis In band MAC address 00 04 0D 17 A4 00 Chassis Out band MAC address 00 04 0D 17 A4 FE Chassis Serial number 4552086 Chassis CS e130 SPV 1 SPV 2 Mode Standby Active Synchronized Yes Yes EmWeb version 2 50 42 2 0 2 Bank A version 2 0 2 2 0 2 Bank B version 2 072 2 0 2 Preferred Bank Bank A Bank A Serial Number 4559466 4559417 C S Number 1 0 1 0 Running Version 2 0 2 2 0 2 Booted From Bank A Bank A Avaya C460 Reference Guide 215 Chapter
88. ad write admin You can only access this command in Router OSPF mode Type router ospf at the command prompt to enter Router OSPF mode if necessary Use the area command to configure the area ID of the router Use the no area command to delete the area ID of the router set it to 0 and remove the stub definition The default area is 0 0 0 0 O You cannot define a stub area when OSPF is redistributing other protocols or when the Area ID is 0 0 0 0 The syntax for this command is no area lt area id gt lt stub gt area id IP address stub Stub Example Router 1 configure router ospf area 192 168 49 1 Router 1 configure router ospf area 192 168 49 1 stub Avaya C460 Reference Guide 13 Chapter 2 Avaya C460 CLI Commands arp User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the arp command to add a permanent entry to the Address Resolution Protocol ARP cache Use the no arp command to remove an entry either static entry or dynamically learned The syntax for this command is no arp lt ip address gt lt mac address gt ip address IP address in dotted decimal format of the station mac address MAC address of the local data link Example To add a permanent entry for station 192 168 7 8 to the ARP cache C460 1 config
89. algorithm for the switch When you disable STP blocking ports are disabled in order to prevent loops in the network As a result you need to wait 30 seconds before disabling STP if you reset the switch enable STP or insert a new station The syntax for this command is set spantree enable disable Example CA460 14 set spantree enable bridge spanning tree enabled C460 1 set spantree disable bridge spanning tree disabled Avaya C460 Reference Guide 131 Chapter 2 Avaya C460 CLI Commands set spantree forward delay User level read write admin Use the set spantree forward delay command to set the bridge forward delay time parameter The syntax for this command is set spantree forward delay lt time gt forward The time that is used when transferring the port to forwarding state delay Value range is 4 30 and must exceed Bridge Max Age 2 Recomended value is 15 seconds Example C460 1 set spantree forward delay 15 bridge forward delay set to 15 set spantree hello time User level read write admin Use the set spantree hello time command to set the bridge hello time parameter The syntax for this command is set spantree hello time lt time gt hello The time interval in seconds between the generation of time configuration BPDUs by the Root Value ranges between 1 to 10 and must not exceed Bridge Max Age 2 1 The recommended value is 2 sec Example
90. ally a client is an application that runs on a personal computer or workstation and relies on a server to perform some operations Collision In Ethernet a collision occurs as the result of two nodes transmitting simultaneously The frames from each device impact and are damaged from the impact CRC Cyclic Redundancy Check A data transmission error checking technique in which the frame recipient calculates a remainder by dividing frame contents by a prime binary divisor and compares the calculated remainder to a value stored in the frame by the sending node CSMA CD Carrier Sense Multiple Access with Collision Detection A multi user network allocation procedure in which every station can receive the transmissions of all others Each station waits for the network to be idle before transmitting and each station can detect collisions by other stations Data Link Layer Layer 2 of the OSI reference model The Data Link Layer is responsible for physical addressing network topology line discipline error notification ordered delivery of frames and flow control DHCP Dynamic Host Configuration Protocol A protocol for assigning dynamic IP addresses to network devices With dynamic addressing a device can have a Avaya C460 Reference Guide 243 Glossary different IP address every time it connects to the network In some systems the device s IP address can even change while it is still connected DHCP also supports a mi
91. ample The minimum time between redundancy switchovers for each pair in milliseconds The period the primary port link has to be up before the system switches back in milliseconds e Ifswitchback interval is zero the system never switches back e Ifitis one switchback occurs immediately after the primary port link returns The system switches bank only if the secondary link fails Done CA460 14 set port redundancy intervals 100 20 set port spantree User level read write admin Use the set port spantree command to enable or disable the spanning tree mode for specific switch ports The syntax for this command is set port spantree enable disable module port enable disable Enables or disables the spanning tree mode for the specified ports Module Module number Port Port number Example C460 1 set port spantree enable 3 1 port 3 1 was enabled on spantree 116 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set port spantree cost User level read write admin Use the set port spantree cost command to set the cost of a port This value defines which port will be allowed to forward traffic if two ports with different costs cause a loop The syntax for this command is set port spantree cost module port value module Number of the module 3 6 port Number of the port on the module If you do not specify a number the port spantree cost i
92. and to display the static routes The syntax for this command is show ip route static lt ip addr gt lt mask gt ip address The IP address of the routes mask The ip mask of the routes 164 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example Router 1 gt sh ip route static Showing 34 rows Network Mask Interface Next Hop Cost PrefActive 10 0 8 0 255 255 255 0e 36 149 49 36 11 1 high Yes 135 0 0 0 255 0 0 0 e 135new 135 64 76 11 high Yes 135 64 0 0 255 255 0 0 e 135 135 87 154 1 1 high No 149 49 0 0 255 255 0 0 zevel10 10 254 2531lowYes 149 49 2 0 255 255 255 0n av Route FWlhighYes show ip route summary User level read only read write admin Use the show ip route summary command to display the number of routes known to the switch The syntax for this command is show ip route summary Example Router 1 gt sh ip route summary IP Route Summary Current number of routes 69 show ip traffic User level read only read write admin Use the show ip traffic command to display the IP traffic statistics counters The syntax for this command is show ip traffic Avaya C460 Reference Guide 165 Chapter 2 Avaya C460 CLI Commands Example Router 1 gt show ip traffic IP statistics Received 1365359 total 45659 local destination 0 bad hop count 0 packet header errors 0 unknown protocol 136786 address errors 1182914 discarded
93. arketing to be listen only Router 1 configure if marketing ip rip send receive mode talk listen Done ip rip split horizon User level read write admin O You can only access this command in interface mode Type interface name at the command prompt to enter interface mode if necessary Use the ip rip split horizon command to enable split horizon mechanism Use the no ip rip split horizon command to disable the split horizon By default split horizon is enabled The split horizon technique prevents information about routes from exiting the router interface through which the information was received This prevents routing loops The syntax for this command is no ip rip split horizon 58 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example Router 1 configure if marketing no ip rip split horizon Done ip route User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip route command to establish a static route Use the no ip route command to remove a static route The syntax for this command is no ip route lt ip address gt mask next hop lt next hop gt lt next hop gt lt cost gt lt preference gt ip address The IP address of the network mask Mask of the static route
94. asthe Login name and the default password root inlowercase letters Welcome to C460 SW version 1 0 0 Login root Password Password accepted C460 1 super Defining new users Define new users and access levels using the username command in Supervisor Level Exiting the Supervisor Level To exit the Supervisor level type the command exit Avaya C460 Reference Guide 9 Chapter 1 Using the CLI Entering the CLI To enter the CLI enter your username and password Your access level is indicated in the prompt as follows The User level prompt is shown below C460 1 gt The Privileged level prompt is shown below C460 1 The Configure level prompt for Layer 3 configuration is shown below C460 configure The Supervisor level prompt is shown below C460 super Entering the Technician Level This level is can only be accessed from the Privileged and Supervisor levels not from the User level O This feature is for use by Avaya Technical Support only Getting Help On line help may be obtained at any time by typing a question mark or the word help on the command line or by pressing the F1 key To obtain help for a specific command type the command followed by a space and a question mark Example C460 1 gt show C460 1 gt help show Command Syntax Commands are not case sensitive That is uppercase and lowercase characters may be inter
95. ated if you attempt to set the transmission type of auto negotiation Fast Ethernet ports to half or full duplex mode The syntax for this command is set outband duplex full half Full Sets full duplex transmission Half Sets half duplex transmission Example C460 1 set outband duplex full Ethernet Console interface set to full duplex set outband negotiation User level read write admin Use the set outbound negotiation command to enable or disable the link negotiation protocol on the Ethernet console port This command applies to the specific supervisor module where you execute it e When negotiation is enabled the speed and duplex of the outband Ethernet port is determined by auto negotiation e If negotiation is disabled you can set the speed and duplex of the outband Ethernet port 96 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is set outband negotiation enable disable enable Enable link negotiation protocol disable Disable link negotiation protocol Example C460 1 set outband negotiation enable Auto negotiation for outband port set successfully set outband speed User level read write admin Use the set outband speed command to configure the speed of Ethernet Console port In auto negotiation mode the port s speed is determined by auto negotiation If you attempt to set the speed when auto negotiation is enabled the foll
96. ateway router Use theno ip default gateway command to remove the default gateway The syntax for this command is no ip default gateway lt ip address gt lt cost gt lt preference gt ip address The IP address of the router cost The path cost The default is 1 preference Preference either High or Low Default is Low Example To define the router at address 192 168 37 1 as the default gateway C460 1 configure ip default gateway 192 168 37 1 ip directed broadcast User level read write admin O You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode Use the ip directed broadcast command to enable net directed broadcast forwarding Usetheno ip directed broadcast command to disables net directed broadcasts on an interface The syntax for this command is no ip directed broadcast Example Router 1 config if marketing ip directed broadcast Avaya C460 Reference Guide 47 Chapter 2 Avaya C460 CLI Commands ip icmp errors User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the icmp error command to turn ICMP error messages on Use the no icmp error command to turn ICMP error messages off The syntax for this command is no ip icmp errors Example T
97. ax for this command is set port dotlx port control module port mode module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 mode force unauthorize the port is always is blocking state auto forwarding blocking depends on authorization outcome force authorize the port is always in forwarding state Example C460 1 super set port dotlx port control 2 3 force authorize port 1 2 control was set to force authorize 102 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set port dot1x quiet period User level admin Use the set port dotix quiet period command to set the 802 1x quiet period per port The syntax for this command is set port dotix quiet period lt module port gt seconds module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 seconds Quiet period in seconds 0 to 65535 Example C460 1 super set port dotix quiet period 4 2 300 set port dot1x re authenticate User level admin Use the set port dotix re authenticate command to set the port to re authenticate The syntax for this command is set port dotix re authenticate module port module Module and port number port You can also specify a range of ports separated by a dash for exampl
98. aya C460 CLI Commands The syntax for this command is set power redundancy lt mode gt enable Enable power redundancy disable Disable power redundancy Example C460 1 set power redundancy enable set powerinline budget User level read write admin Use the the set powerinline budget command to recalculate and reapply the PoE budget The syntax for this command is set powerinline budget Example C460 1 set powerinline budget Powerinline budget was reinitialized set ppp authentication incoming User level read write admin Use the set ppp authentication command to define the authentication method used for a PPP server or client session The syntax for this command is set ppp authentication incoming pap chap none pap PAP authentication method chap CHAP authentication method none No authentication 122 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 set ppp authentication incoming chap PPP requires CHAP authentication for incoming sessions set ppp baud rate User level read write admin Use the set ppp baud rate command to define the baud rate used in PPP sessions O You mujst set the peer baud rate to the same value as the host The syntax for this command is set ppp baud rate lt 9600 19200 38400 gt Example C460 1 set ppp baud rate 38400 ppp baud rate was set to 38400 set ppp chap secret
99. band Enables the inband interface Example C460 1 en interface inband This command will RESET the device Reset do you want to continue Y N Y Attaching network interface 100 done Welcome to C460 SW version 1 0 1 Login enable vlan commands User level read write admin O You can only access this command in interface mode Type interface name at the command prompt to enter interface mode Use the enable vlans commands command before configuring VLAN oriented parameters when there is more than one interface on the same VLAN The syntax for this command is enable vlan commands Example Router 1 config if marketing enable vlan commands 32 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands erase startup config User level read write admin Use the erase startup config command to clear the startup configuration The syntax for this command is erase startup config Example C460 1 erase startup config fragment chain Use the fragment chain command to set the maximum number of fragments that can comprise a single IP packet destined to the router Usethe no fragment chain command to set the fragment chain to the default value 64 The router does not perform reassembly of packets in transit The syntax for this command is no fragment chain lt chain limit gt chain limit The maximum number of frag
100. ccess request is sent when there is no response The syntax for this command is set radius authentication retry number lt number gt number Number of retries Example C460 1 super set radius authentication retry number 3 124 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set radius authentication retry time User level read write admin Sets the time to wait before re sending an access request The syntax for this command is set radius authentication retry time lt time gt time Retry time in seconds Example C460 1 super set radius authentication retry time 5 set radius authentication secret User level read write admin Use the set radius authentication secret command to enable secret authentication for the P330 unit The syntax for this command is set radius authentication secret string string text password Example C460 1 super set radius authentication secret hush set radius authentication server User level read write admin Sets the IP address and shared secret of the primary or secondary RADIUS Authentication server The syntax for this command is set radius authentication server ip addr primary secondary ip addr IP address of the RADIUS authentication server primary default Primary authentication server Avaya C460 Reference Guide 125 Chapter 2 Avaya C460 CLI Commands secondary Secondary a
101. ce mode if necessary Use the ip bootp dhcp server command to add a bootp dhcp server to handle bootp dhcp requests received by this interface Use the no ip bootp dhcp server command to remove the server A maximum of two servers can be added to a single interface The syntax for this command is ip bootp dhcp server lt ip address gt ip address The IP address of the server Example To add station 192 168 37 46 as a bootp dhcp server to handle bootp dhcp requests arriving at the interface marketing Router 1 configure if marketing ip bootp dhcp server 192 168 37 46 Done ip broadcast address User level read write admin O You can only access this command in interface mode Type interface name at the command prompt to enter interface mode Use the ip broadcast command to update the interface broadcast address The Broadcast address must be filled in with Os or 1s The syntax for this command is ip broadcast address bc addr gt bc addr The broadcast IP address Example Router 1 config if marketing ip broadcast address 192 168 255 255 46 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands ip default gateway User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip default gateway command to define a default g
102. changed freely Command Abbreviations All commands and parameters in the CLI can be truncated to an abbreviation of any length as long as the abbreviation is not ambiguous For example version can be abbreviated ver For ambiguous commands type the beginning letters on the command line and then use the TAB key to toggle through all the possible commands beginning with these letters 10 Avaya C460 Reference Guide Chapter 1 Using the CLI Router Configuration Contexts You can either use the general C460 commands available from the Router configure prompt or you can enter one of two router configuration context modes e Router interface context This allows you to define parameters individually for each interface To enter this context type interface lt interface_name gt The prompt changes to Router gt config if lt interface_name gt e Router protocol context This allows you to define parameters for a specific routing protocol RIP OSPF and VRRP To enter this context type router lt protocol_name gt The prompt changes to Router gt configure router protocol_name To exit these context modes type the command exit Avaya C460 Reference Guide 11 Chapter 1 Using the CLI 12 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands access list area This chapter describes all the C460 CLI commands and parameters in alphabetical order See ip access list User level re
103. clear system log eren ene tenent teret 23 clear timeZone oet recorre tence tb Sasha ce Hee RUAN ee rna 23 cleat vlan zar a Ee ie niti tend o e t thea thine ce leto reto e as 24 clear vlan Layer AAA A foede ect E cet te 24 CONTE Ute ais here I e Oi a e enel e nere A nete edens 25 copy config tftp eire teer rtr here teet tarte ens 25 copy running config startup config ssssssssssseeenee 25 copy startup config tftp sneer grii a ai eene 26 copy tttp EW archive tete erede eter eerie 27 copy tftp config slender re terree e eere tas 27 copy tftp start p cohfig muralla ni ee an rp rr tel e cies 28 copy tftp SW imageA esaera aeaee esei a reete nenne nennen nennen 28 copy tftp SW imageB 5 onere temere ito eterna 29 default MECI s A NAT 30 default metric OSPF esee enne entrent teen 30 default metric RIP ae eee tete tenent 31 disable t iterface A eee cree A eae e Pre E 31 Enable interface rra eu id ide 32 enable vlan commands seen nennen 32 erasestartup contig cup eee tee eee teet oti aa 33 fragment chain 3 25 ee ertet ee ete e edes 33 frdgmentsize cti id tette re Lt rtt tetas 33 fragment timeout nee pue pe nette nere t df e 34 BOETHII iius esee tree ee Eee e p e ere rt eee Er ete ese N 34 OSMA eoe ete e eed E AE Ds 34 hostname Luci idee suse suet petiere perlas 35 interface o seen tate cii od Dif ON 36 ip access default action moccococonenononnononennnnrnnnncannnnnnnnarnrannnnana
104. command to assign an IP address to the virtual router Use the no ip vrrp address command to remove an IP address from a virtual router 62 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is no ip vrrp lt vr id gt address lt ip address gt vr id Virtual Router ID 1 255 ip address The IP address to be assigned to the virtual router Example To assign address 10 0 1 2 to virtual router 1 Router 1 configure if marketing ip vrrp 1 address 10 0 1 2 Done ip vrrp auth key User level read write admin O You can only access this command in Interface mode Typeinterface name atthe command prompt to enter Interface mode if necessary Use the ip vrrp auth key command to set the virtual router simple password authentication for the virtual router ID Usetheno ip vrrp auth key command to disable simple password authentication for the virtual router instance The syntax for this command is no ip vrrp lt vr id gt auth key lt key string gt vr id Virtual Router ID 1 255 key string Simple password string ip vrrp override addr owner User level read write admin O You can only access this command in Interface mode Typeinterface name atthe command prompt to enter Interface mode if necessary Usethe ip vrrp override addr owner command to accept packets addressed to the IP address es associated with the virtual router such as ICMP
105. communications unit that may be used in combination with other units Examples include individual Avaya P330 units and cards that slot into the Avaya P580 P882 Device Multicasting A method of information transmission in which copies of the packet are delivered to multiple ports but only a subset of all possible destinations NAS Network Access Server A network device that allows access to a network e g the Avaya C460 Netmask A portion of an IP address that identifies the bits that denote the network number Network A collection of computers printers routers switches and other devices that can communicate with each other over some transmission medium A network can consist all or in part of subnetworks Network Agent A special control module that interfaces between the network manager and the managed devices using the MIB as a management terms dictionary Network Agents relay device events and execute instructions via embedded software Network Mask A portion of an IP address that identifies the bits that denote the network number NMS Network Management Station A station that is responsible for managing all or part of a network An NMS communicates with Network Agents to help keep track of network statistics and resources Node A point of interconnection to a network or a junction of two or more lines in a network A node can be a computer or some other device such as a printer Every node has a unique
106. cookie gt lt policy list number gt integer 100 to 149 lt cookie gt integer Example C460 1 configure ip access list cookie 101 12345 ip access list copy User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access list copy command to copy a configured source policy list to a destination policy list The syntax for this command is ip access list copy source list lt destination list gt lt source list gt integer 100 to 149 0 is the default list lt destination list gt integer 100 to 149 Avaya C460 Reference Guide 39 Chapter 2 Avaya C460 CLI Commands Example C460 1 configure ip access list copy 100 101 ip access list dscp name User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access list dscp name command to set a name for a dscp entry The syntax for this command is ip access list dscp name lt policy list number gt lt dscp gt lt name gt lt policy list number gt integer 100 to 149 dscp DSCP entry 0 to 63 lt name gt entry name Example C460 1 configure ip access list name 101 16 special If you wish
107. creen 1 tree 1 logout time timezone snmp intelligent multicast port trunk Spantree vlan Spv cam powerinline icmp redirect interface outband device mode access lists system module type q to quit or space key to continue username User level admin Adds a local user account O By default there is only a single user account named root with password root which access the administrator level You cannot delete this basic user account nor modify its access level but can modify its basic password The syntax for this command is username lt name gt password lt passwd gt access type read only read write admin name passwd New user name minimum four characters User s password minimum four characters Avaya C460 Reference Guide 229 Chapter 2 Avaya C460 CLI Commands access type Access type definition read only read write or administrator Example C460 1 super username john password johnny access type read write User account added C460 1 super username root password secret access type read write ERROR User account root has always an administrator access type C460 1 super username root password secret access type admin User account modified If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york validate group User level read write admin
108. d by a dash for example 4 5 13 for ports 5 to 13 on module 4 admin force true treat this port as if it is connected point to point status force false treat this port as if it is connected to shared media auto try to automaticaly detect the connection type of the port 112 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 set port point to point admin status 1 1 force true port 1 1 point to point admin status is set to force true set port powerinline User level read write admin Use the set port powerinline command to enable or disable the load detection process on the port The syntax for this command is set port powerinline lt module_number port_number gt enable disable module Number of the module 3 6 port Number of the port on the module If you do not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 enable Enable load detection on the port disable Disable load detection on the port Example To enable PoE on ports 1 to 3 of module three C460 1 set port powerinline 3 1 3 enabl Load detection process on ports 3 1 3 is enabled set port powerinline priority User level read write admin Use the set port powerinline priority command to set the priority level for powering the port The syntax for this command is
109. d flow Admin control frames to the far end e OFF indicates that the local port is not allowed to send flow control frames to the far end Send Send flow control operation mode Possible modes Flowcontrol ON indicates that the local port will send flow control frames Oper to the far end e OFF indicates that the local port will not send flow control frames to the far end Receive Receive flow control administration Possible settings Flowcontrol ON indicates that the local port will act upon flow control Admin indications if received from the far end e OFF indicates that the local port will discard flow control frames if received from the far end Receive Receive flow control operation mode Possible modes Flowcontrol ON indicates that the local port will act upon flow control Oper indications received from the far end e OFF indicates that the local port will discard flow control frames received from the far end show port mirror User level read only read write admin Use the show port mirror command to display mirroring information for the switch The syntax for this command is show port mirror Avaya C460 Reference Guide 195 Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show port mirror port mirroring Mirroring both Rx and Tx packets from port 3 2 to port 4 4 is enabled C460 1 gt show port mirror port mirroring No ports are mirrored show port point to
110. d inside inverted commas The location is cleared if you leave this field blank Example C460 1 set system location tech support Set system location system location set If you wish to enter a name which includes spaces you must enclose the entire name in quotation marks for example new york set system name User level read write admin Usethe set system name command to set the mib2 system name MIB variable The syntax for this command is set system name string string The system name string should be typed inside inverted commas Thename is cleared if you leave this field blank Example C460 1 set system name C460 1 Set system name System name set If you wish to enter a name which includes spaces you must enclose the entire name in quotation marks for example new york Avaya C460 Reference Guide 135 Chapter 2 Avaya C460 CLI Commands set time client User level read write admin Use the set time client command to enable or disable the periodic network time acquisition by the switch from the network time server SNTP or TIME protocol The syntax for this command is set time client enable disable enable Enable periodic network time acquisition disable Disable periodic network time acquisition Example C460 1 set time client enable Time client mode enabled set time protocol User level read write admin Use
111. deny default action permit Example C460 1 configure access default action 101 default action deny ip access group User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access group command to activate a specific policy list Use the no ip access group command to deactivate the policy list The syntax for this command is no ip access group lt policy list number gt lt default action gt lt priority list number gt integer 100 to 149 0 is the default list lt default action gt default action deny default action permit Example C460 1 configure ip access group 101 Avaya C460 Reference Guide 37 Chapter 2 Avaya C460 CLI Commands ip access list User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access list command to create a specific policy rule The access list contains several of these rules each rule pertains to the source IP address the destination IP address the protocol the protocol ports if relevant and to the ACK bit if relevant Use theno ip access list command to delete a specific rule The syntax for this command is no ip
112. ds Total working fans Fans not installed show environment power User level read only read write admin 9 8 less than 8 No fan tray installed Usethe show environment power command to display the current power configuration for the switch the total power available to the system and amount of power currently in use O The Main Power includes two supervisor modules and the fan module irrespective of the number of supervisor modules installed O The Main Draw column shows the demand for an I O module whether its slot is enabled or not The syntax for this command is Show environment power Example Slot Power Available M460ML SPV M460ML SPV M4612M M4648M M4648M M4648M L G L T 2G PWR L T PWR L T 2G Fans power consumption C460 gt show environment power PSUs Configuration Admin PSUs Configuration State Active Enabled Priority Draw Budget Draw Fault 45 W redundancy no redundancy Drawn Remaining 2 active PSU s critical critical low high low low Main PoE PoE 68W 68W 59W 48W 720W 100W 48W 720W ow 70W 152 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show erase status User level user privileged supervisor Use the show erase status command to view the status of the erase configuration operation The syntax for this command is show erase status show ev
113. e Example C460 1 super show username User account password access type root KRAAN admin gkohll TUE read only readwrite Wee read write show vlan User level read only read write admin Use the show vlan command to display the VLANs configured in the switch The syntax for this command is show vlan 222 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show vlan VLAN ID Vlan name L v1 5 V5 LO V10 15 V15 20 v20 25 V25 show vlan Layer 3 User level read only read write admin Use the show vlan command to display router Layer 2 interfaces The syntax for this command is show vlan Example Router 1 show vlan VLAN NAME VLAN ID VLAN MAC Default 1 02 e0 3b 1d f9 01 show web aux files url User level read only read write admin Displays the URL directory from where the switch can access the Device Management auxiliary files for example help files The syntax for this command is show web aux files url Example C460 1 gt show web aux files url the web aux files url is 149 49 36 212 C460test Avaya C460 Reference Guide 223 Chapter 2 Avaya C460 CLI Commands sync spv User level read write admin Use the sync spv command to synchronize the following between an Active Supervisor Module and Halted Supervisor Module e Boot bank e Firmware images e D
114. e 4 5 13 for ports 5 to 13 on module 4 Example C460 1 super set port dotix re authenticate 1 2 port 1 2 is not in authenticating process set port dot1x re authentication User level admin Use the set port dotix re authentication command to set the re authentication mode per port Avaya C460 Reference Guide 103 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set port dotlx re authentication module port mode module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 mode enable disable Example C460 1 super set port dotix re authentication 1 2 enable port 1 2 re authenticate was set to enable set port dot1x re authperiod User level admin Use the set port dotix re authperiod command to set the the idle time between re authentication attempts before the session is terminated The syntax for this command is set port dotix re authperiod module port seconds module Module and port number port You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 seconds Idle time in seconds 0 to 65535 Example C460 1 super set port dotix re authperiod 1 2 400 set port dot1x server timeout User level admin Use the set port dotlx server timeout command to set the time to wait
115. e command prompt to enter configure mode Use the ip netmask format command to specify the format of netmasks in the show command output Use the no ip netmask format command to restores the default format which is a dotted decimal The syntax for this command is no ip netmask format lt mask format gt The possible mask formats are bitcount Addresses are followed by a slash and the total number of bits in the netmask For example 17 decimal The network masks are in dotted decimal notation For example 255 255 255 0 hexadecimal The network masks are in hexadecimal format as indicated by the leading 0X For example OXFFFFFFOO 50 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example To display netmasks in decimal format C460 1 configure ip netmask format bitcount decimal Done ip ospf authentication key User level read write admin O You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip ospf authentication key command to configure the interface authentication password Usethe no ip ospf authentication key command to remove the OSPF password The syntax for this command is no ip ospf authentication key lt key gt key string up to 8 characters Example Router 1 configure if marketing ip ospf authentication key my pass ip ospf cost User leve
116. e ee nest ei eret a eee ege 51 ip ospf d ad interval edet re dete triti ida 52 ip Ospf hellocintetval 5nd a tt eit re ierit treats 52 Ip OSpEpEOority zc cec tate ee iet tte ecu tee tates 53 ip ospfro ter Id nit nnne eter Le eere eer t eee 53 IP PrO AIP 54 ip redirects uite es e tefte dae ne bane uie EEE dae 54 ip rip authentication Key sse een enne 54 ip rip authentication mode 05 s 55 ip rip default route mode 7 sees 56 ip rip poison reverse iesita ar aena ea a eana ea Ras 56 ip rip rip versiOn ooi isina reie e ane eaei entente AEEA COAR Kan ke 57 ip rip send receive mode csse eene nens 57 Ip TIP SPT OLIZON cui temet eH ete pen 58 Up TOUTE A 59 Ip XOUllDg oscar ose se e ie E eerte PETRO RE TRA PESE En 59 ip routing mode sao rete tete iie eere feres 60 Ip simulator oce dee der LE cu 61 ip vlan ip vlan Mame sitiens i i iae as 61 Ip VITD E A EE A ie E edet ed E diete 62 Lp vrp address inr a E A A E pede E S 62 TP VATP auth key serye reete deett tete 63 ip vrrp override addr owner sss 63 IP VITP Prepi 64 Avaya C460 Reference Guide iii Contents IPD PEAY dE 64 A ien ta A AEE EAEE 65 UP VEEP tner lae bn e tp a Ei a NG oh Us titii 66 A escam case eh E chs cc EA rte E AA 66 network RIP 2 nene AA oes ea ROTE 67 network OSPE vit 67 Doxmori latim sau n cute teni ie pleine baee eal e
117. e is set to 5 seconds show banner login User level read only read write admin Use the show banner login command to display the message shown before a login The syntax for this command is show banner login Avaya C460 Reference Guide 143 Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show banner login Welcome to C460 SW version 2 0 2 show banner post login User level read only read write admin Use the show banner login command to display the message shown after a successful login The syntax for this command is show banner post login Example C460 1 gt show banner post login Welcome to C460 SW version 2 0 2 show boot bank User level read only read write admin Use the show boot bank command to display the system boot bank The syntax for this command is show boot bank Example C460 1 gt show boot bank SPV 1 boot bank is A show broadcast storm control User level read only read write admin Use the broadcast storm control command to display broadcast storm status and settings 144 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is show broadcast storm control Example C460 1 gt show broadcast storm control Broadcast Threshold Storm Control disable 500 show cam User level read only read write admin Use the show cam command to display the
118. eee e tii 154 show image Version treinta 154 show intelligent multicast onncncnninnononnoninnnnnnnnnnnnonoronnonncn rocio no nn 154 Show 1nlerfate 7 scc ecce tete dir exer eee ree ee ete e OARS 155 SHOW ip access group setor e terere tet a E eee tte trees 155 show ip access list dscp eoocococononcnonnnnonnnnrnronnenennnnnnrnnnanarnnnnnn rn rnrnennnaranannnoa 156 show ip access lists iii eei e wees heh e bete ad 156 show ip access list summary eee eene 157 SHOW Ip arp seen dece etie Aiea baleen 157 SHOW E ioBruvd o 158 show ip interface iet theres itd teda 159 show ip interface brief sse eee eene 160 Avaya C460 Reference Guide vii Contents Show ip OSpl ii dt re iii ee er i een rtt it 160 show ip ospf database sse e eee e nnns 161 show ip Ospf interface isi haia esii ite ritenere 161 show ip ospf neighbor oc cece esse eee eee e eene 162 show ip protocols eti eee nete eere enint 162 show ip rev rse atp nee rettet rentre tree ries 163 show ipiroute ueste rete Daten REP a rere en hte ntt eer dos 163 show ip route Layer 3 orisiirisii ede asii ie 163 show ip route best match sss eee enne 164 show ip route static eene 164 show ip route summary encccccinoconinnnnonnnnnnnnnanannnonononanonononononanononononanananonenss 165 show ip traffic coccoccnconcncnnncnnonenenenenonnnnnnnnnrarnnnnnnnannnnnnarnrannn aaee ar a nn rarananannaro 165 show ip
119. en elas 68 TO TMON OVEN aldo A eet tete eee beet da ed cha i Ra 68 DO Xmon histoEy een tae 69 nO Sefnat e vti A ee dee e he eve due 69 nvramceanitiallze x oon lhe Me ala ea oS eot D EDU nter 69 passive interface u c edu Acte tenet t e ot et tete Pe deti xut 70 A 71 ping Layer ii dee tete ettet tete stesse dete hues 7i redistribute OSPF ettet Be eee ita 72 redistribute RIP not Re e Coe Rechte 72 TOS n 73 PINION A LATIN ete tote a tio aah aes 75 rmon eventi udo te e aee Her ele eie ne ois e d Peek Pere 76 PINON HISHOLY i c oed de aee a e aaa eases Lanse 76 rmon2 protocol dir eoe abia 77 rmon2 Protocol dist eire ttt rete reete fe tetas 77 router ospis nop gne tei ne at tenete a 78 A T 78 FOET VEL e boned 79 SESSION ROO 79 set allowed managers sse eee ene nennen 80 set allowed managers ip sse eee eee 80 set arp aging interval Lesire isisi iee iee nnns 81 set arp O interval 2 22 t re etre ee pie Ente ettet errantes 81 Ssetboot bank 3 doe t eru teni epi eet itu n e hee wees 82 set broadcast storm control sse eene 82 set broadcast storm control threshold sss 83 set devicesmod AA tette reae Deseo eee earn a E E 83 set device mode Layer 3 sse eee 84 sebdot Examaxereq e oet eue tette de ie ees 84 set dotIx quiet period nete retentis 84
120. ent log User level read only read write admin Displays the encrypted event log file The syntax for this command is show event log show event log Layer 3 User level read only read write admin Displays the encrypted event log file The syntax for this command is show event log show fragment User level read only read write admin Use the show fragment command to display information regarding fragmented IP packets that are destined to the router The router does not perform reassambly of packets in transit This command displays the following information Size Maximum number of packets set by the fragment size command Chain Maximum number of fragments for a single packet set by the fragment chain command Timeout Maximum number of seconds set by the fragment timeout command Queue Number of packets currently awaiting reassembly Assemble Number of packets successfully reassembled Fail Number of packets which failed to be reassembled Avaya C460 Reference Guide 153 Chapter 2 Avaya C460 CLI Commands Overflow Number of packets which overflowed the fragment database The syntax for this command is show fragment Example Router 1 gt show fragment Max number of concurrently reassembled packets is 100 Max number of fragments per packet is 64 Fragment timeout is 10 sec Number of packets waiting to be reassembled is 0 Number of successfully reassembled packets is 11954 Number of
121. entication requests Tx Priod The amount of time in seconds in which an authentication request must be answered 192 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Max Req The maximum number of times a request for authentication is sent before timing out show port dot1x statistics User level read only read write admin Use the show port dotlx statistics command to display all the port dotlx statistics The syntax for this command is show dotix statistics mod port module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the module If you do not specify a number Optional all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 gt show port statistics 1 1 Port Tx Reg Id Tx Req Tx Total Rx Start Rx Logff Rx Resp Id Rx Resp Port Rx Invalid Rx Len Err Rx Total Last Rx Frm Ver Last Rx Frm Src Mac 1 1 0 0 0 0 1d 80 00 00 00 00 Avaya C460 Reference Guide 193 Chapter 2 Avaya C460 CLI Commands show port edge state User level read only read write admin Use the show port edge state command to show a port s edge admin and operational RSTP state O A port can be set to admin state of edge port but if a BPDU is received on this port the oper state is changed to non edge state
122. er 1 gt show rmon2 protocol dir Protocol Description Owner FTP data over TCP IP Port 20 Telnet over TCP IP Port 23 SMTP over TCP IP Port 25 HTTP over TCP IP Port 80 1111 tcp CLI_User on local device 2222 tcp CLI_User on local device SNMP trap over UDP IP Port 162 show rmon2 protocol dist User level read only read write admin Use the show rmon2 protocol dist command to display the RMON2 protocol distribution information The syntax for this command is show rmon2 protocol dist UDP TCP Port gt UDP UDP protocol TCP TCP protocol Port Port 206 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example Router 1 gt show rmon2 protocol dist Protocol Total Packets Total Octets Utilization ICMP 316 0 17 OSPF 5033 2 77 VRRP 0 0 00 RIP 0 0 00 Other 176031 97 06 Total IP control 181380 100 00 FTP data over TCP IP Port 20 0 0 0 00 Telnet over TCP IP Port 23 0 0 0 00 SMTP over TCP IP Port 25 0 0 0 00 HTTP over TCP IP Port 80 0 0 0 00 1111 tcp 7587263 485584832 59 99 2222 tcp 5058185 323723840 40 00 SNMP trap over UDP IP Port 162 0 0 0 00 Other 0 0 0 00 Total IP routed 12645448 809308672 100 00 Total IP 12826828 ARP Protocol 530811 Avaya C460 Reference Guide 207 Chapter 2 Avaya C460 CLI Commands show rmon2 state User level read only read write admin Use the show rmon2 state command to display the stat
123. er level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access list dscp precedence command to The syntax for this command is ip access list dscp precedence lt policy list number gt lt dscp gt lt precendence gt policy list A valid id number for a policy list currently defined for the number module 100 to 149 dscp DSCP entry 0 to 63 precedence mandatory optional Avaya C460 Reference Guide 41 Chapter 2 Avaya C460 CLI Commands Example C460 1 configure ip access list dscp precedence C460 1 configure ip access list dscp trust User level read write admin Use the ip access list dscp trust command to decide which original frame fields influence the selection of packet priority The syntax for this command is ip access list dscp trust lt policy list number gt untrusted trust cos trust dscp policy list A valid id number for a policy list currently defined for the module number 100 to 149 untrusted Forward the packet with priority 0 trust cos Forward the packet with its original 802 1p priority default trust dscp Forward the packet with the maximum priority between 802 1p and the priority obtained from the DSCP CoS mapping table Example Cc460 1 configure ip access list dscp trust 100 trust dscp Done ip access list name User level read write adm
124. et set set set set set set set set set set set 1 IE TH 14 set intelligent multicast parameters intelligent multicast disable intelligent multicast client port pruning time 600 intelligent multicast router port pruning time 1800 intelligent multicast group filtering delay time 10 d broadcast storm configuration broadcast storm control threshold 0 set broadcast storm control disable KKK KKK KKK KKK KKK KKK KK KKK KK KK KK KKK KK KKK KK KK KKK ckckockckckckck kck kckokok LINK AGGREGATION GROUP SPANNING TREE I ERE IS NO LINK AGGREGATION GROUP type q to quit or space key to continue PER PORT CONFIGURATION port spantree port spantree port spantree port spantree port spantree port spantree port spantree port spantree port spantree port spantree port spantree port spantree cost cost cost cost cost cost cost cost cost cost cost cost 5 1 5 2 5 3 5 4 5 5 5 6 5 7 5 8 5 9 5 10 4 5 11 4 5 12 4 K RR RRR BR BR am Avaya C460 Reference Guide 177 Chapter 2 Avaya C460 CLI Commands LPR KK ck ck KK KK RK KKK port 5 1 configuration okckckckck ckckckckck kck kck kk If Port type Tranceiver Not Present 4 Link status no link STA status Disabled Dk KK ck ckckck ck ckckck ckckck ck ckckck kckck ck ck ck ck AS set port disable 5 1 set port auto negotiation flowcontrol advertisement 5 1 no flowcontrol type q to q
125. evel you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the clear vlan command to delete a Router layer 2 interface The syntax for this command is clear vlan lt ifIndex gt name lt ifname gt ifIndex Interface Index ifname Interface name used in layer 3 protocols Example C460 1 configure clear vlan 2 name vlan2 24 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands configure If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york User level read write admin Use the configure command to enter configure mode The syntax for this command is configure Example C460 1 super configure C460 1 configure copy I2 config tftp User level read write admin Use the copy 12 config tftp command to upload the Layer 2 parameters from the current NVRAM running configuration to a file via TFTP O To use this command you need to have an active tftp server and to create a file into which to download the data O If Avaya MultiService Network Manager is running you do not require an additional TFIP server The syntax for this command is copy 12 config tftp filename ip filename file name including full path ip IP address of the host Example C460 14 copy 12 config tftp c C460 config 149
126. eviations eese eene ener ennt 10 Router Configuration Contexts cccccceccccccesssneeesceeesesssesneneseseeneneeseeeenes 11 Chapter 2 Avaya C460 CLI Commands sucio tees 13 access sb oe tme eibi e A NEU e tS 13 ATCA ci IT a ld E A e a E ed 13 A EN IEEE AN 14 arp timeout sn none eee tertie reete niece 14 banner login 2 ene ete niente tt eren reris 15 banner login Tine inier pn on Up reati etai gue corda 15 banner post logiti evitados ias 15 banner post logm line merindad sida 16 clear arpscache 3 esee eee tette tette teet et toe tete cedi 16 clear A eie e ett Dae fe a ed NR nce ftu e iR 17 clear doty config ee net AS 17 clear dynamic V x dede nette eene leere e ir etre eee etn 17 cl ar event log iei ttt ee etr aee repre deett 18 Avaya C460 Reference Guide i Contents clear fragment teet AA E dedi iere ire ies 18 clear Inteftace vos nier ee e a es eere eser e oe rome eee seed ve er 19 clear Ip POU tes nie eee A edipi tete at 19 clear ip route AMA eit diee A 19 Clear ip AAA n eene refero eta 20 CLEAR log ez o rettet tee re te tee eer uentis 20 clear port InirfOE need tete in DR reed epe rrt e cena 20 cl ar port static vlati aee n ee tene aet abe Mee ees 21 clear radius authentication server sese 21 clear rmon32 STATISTICS eis uere e eite a eerte nr Ter e Exe veces 22 cleat SCHOOL iier tette f tes terere Eten be Piste seti Pont 22 cl ar snmp trap is endete tado ttu Te scsi 22
127. evice manager image You can only execute this command from the active Supervisor Module CLI The syntax for this command is sync spv The synchronization may take up to 90 seconds to complete Example C460 1 super sync spv This command may overwrite the neighbor SPV software and reset it Confirmation do you want to continue Y N y Copying Bank A to the neighbor SPV Copying Bank A to the neighbor SPV done Copying Bank B to the neighbor SPV Copying Bank B to the neighbor SPV done Copying Embedded Web image to the neighbor SPV Copying Embedded Web image to the neighbor SPV done Setting boot bank of the neighbor SPV Setting boot bank of the neighbor SPV done Setting chassis sync on for the neighbor SPV Setting chassis sync on for the neighbor SPV done SPVs are resetting Please wait till the process is finished The SPVs will be synchronized after the reset is completed g g g g g g g g The configuration is synchronized after you perform a reset tech Use the tech command to enter tech mode This command is reserved for service personnel use only 224 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands terminal length User level read only read write admin Use the terminal length command to set the length of the terminal display in lines The syntax for this command is terminal length lt screen length gt screen length
128. face outband lt ip_addr gt lt netmask gt ip_addr IP address netmask Subnet mask Example 90 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands To configure the outband interface on VLAN 1 IP address 149 49 75 174 and netmask 255 255 255 24 C460 1 set interface outband 149 49 75 174 24 Interface outband IP address set You must reset the device in order for the change to take effect set interface ppp User level read write admin Use the set interface ppp command to configure the C460 Supervisor Module PPP interface IP parameters exit modem mode disconnect the PPP session or reset the connected modem You must configure an IP address and net mask for the C460 before you can establish a PPP connection The IP address is a dummy address that is shared between two peers and must be taken from a subnet that is different from the agent s IP sub net The syntax for this command is set interface ppp lt ip_addr gt lt net mask gt ip_addr IP address used by the C460 Supervisor Module to connect via its PPP interface net mask Subnet mask used by the C460 Supervisor Module to connect via its PPP interface Example C460 1 set interface ppp 149 49 34 125 24 Interface ppp ip address set set interface ppp enable disable off reset User level read write admin You can also use the set interface ppp command to enter modem mode enter terminal mode disconnect
129. for this command is no ip rip authentication key lt password gt password The authentication string for the interface Up to 16 characters are allowed Example To set the authentication string used on the interface marketing to be hush hush Router 1 configure if marketing ip rip authentication key hush hush ip rip authentication mode User level read write admin O You can only access this command in interface mode Type interface name at the command prompt to enter interface mode if necessary Use the ip rip authentication command to specify the type of authentication used in RIP Version 2 packets Use the no ip rip authentication command to restore the default value of none The syntax for this command is no ip rip authentication mode simple none simple none The authentication type used in RIP Version 2 packets simple clear text authentication none no authentication Example To specify simple authentication to be used in RIP Version 2 packets on the interface Avaya C460 Reference Guide 55 Chapter 2 Avaya C460 CLI Commands marketing Router 1 configure if marketing ip rip authentication mode simple ip rip default route mode User level read write admin You can only access this command in interface mode Type interface name at the command prompt to enter interface mode if necessary Use the ip rip default route
130. ge Access Protocol A protocol for retrieving E mail messages IMAP uses SMTP for communication between the E mail client and server In Band Transmission of auxiliary information such as management messages using the same frequencies or channels normally used for information transfer Internet Protocol Refer to IP on page 247 and TCP IP on page 254 246 Avaya C460 Reference Guide Glossary Internet A collection of networks and gateways that use the TCP IP suite of protocols An internet is two or more networks connected by an internal or external router The word internet is a generic term The Internet is the world s largest internet Interswitch Link ISL Interswitch Link An Avaya proprietary mechanism to tag packets with VLAN and priority information across the backbone This allows two Avaya devices to act as a single logical entity IP The protocol that governs packet forwarding within the TCP IP standards developed and used on the Internet Refer to TCP IP on page 254 IP Address A 32 bit address assigned to hosts using TCP IP An IP address is written as 4 octets separated by periods dotted decimal format Each address consists of a network number an optional subnetwork number and a host number The network and subnetwork numbers together are used for routing while the host number is used to address an individual host within the network or subnetwork A subnet mask is used to extract ne
131. gure routing commands Example To configure router parameters in the module that you are currently logged into type the following command session router When you use the session command the security level stays the same Avaya C460 Reference Guide Chapter 1 Using the CLI Security Levels There are four security access levels modes User Privileged Configure and Supervisor e The User mode is a general access level used to show system parameter values e The Privileged mode is used by site personnel to access switch configuration options e The Configure mode is used by site personnel for Layer 3 configuration e The Supervisor mode is used to define user names passwords and access levels of up to 10 local users A login name and password are always required to access the CLI and the commands The login names and passwords and security levels are established using the username command Switching between the entities does not effect the security level since security levels are established specifically for each user For example if the operator with a privileged security level in the Switch entity switches to the Router entity the privileged security level is retained Entering the Supervisor Level The Supervisor level is the level in which you first enter Cajun Campus CLI and establish user names for up to 10 local users When you enter the Supervisor level you are asked for a Login name Type root
132. h the Supervisor modules Minimal disruption to the traffic 1 Reset Supervisor module in slot 1 2 Reset Supervisor module in slot 2 O If the Supervisor modules are in Active Standby configuration resetting the active supervisor will cause the standby supervisor to take over and become active D The reset command does not work during configuration saving C460 1 reset 1 This command will reset the Active SPV Reset do you want to continue Y N y Reseting Active SBV Avaya C460 Reference Guide 73 Chapter 2 Avaya C460 CLI Commands C460 1 super reset chassis This command will reset the chassis Reset do you want to continue Y N y Reseting chassis C460 1 super Avaya C460 Boot Creation date Jan 6 2003 18 29 57 Press any key to stop auto boot 0 auto booting Bank B is OK SW runs from bank B Welcome to C460 SW version 1 0 5 Login 74 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands rmon alarm User level read write admin Use the rmon alarm command to create a new RMON alarm entry The syntax for this command is rmon alarm lt A larm Number variable interval lt sampletype gt rising threshold rising threshold rising event falling threshold lt fal owner alarm number variable interval sample type rising threshold rising event falling threshold
133. he VLAN Use the no ip bootp dhcp network command to restore the default value 44 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is no ip bootp dhcp network lt ip address gt ip address The IP address of the network Example To select the network 192 168 169 0 as the network from which an address shall be allocated for bootp dhcp requests Router 1 configure if marketing ip bootp dhcp network 192 168 169 0 Done ip bootp dhcp relay User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip bootp dhcp command to enable relaying of bootp and dhcp requests to the bootp dhcp server Use the no ip bootp dhcp command to disable bootp dhcp relay The default state is disabled The syntax for this command is no ip bootp dhcp relay Example To enable relaying of BOOTP and DHCP requests C460 1 configure ip bootp dhcp relay Done To disable relaying of bootp and dhcp requests C460 1 configure no ip bootp dhcp relay Done Avaya C460 Reference Guide 45 Chapter 2 Avaya C460 CLI Commands ip bootp dhcp server User level read write admin You can only access this command in Interface mode Type interface name at the command prompt to enter Interfa
134. ig mrgreen eeaeee aren aa tete tenenti 216 ShoWw SyStem n Adee acts recta tetas ries tees eere ete ett eher de ee n 217 SHOW Systemilog i5 tette te rede etti edet ire ends 217 show system log Layer 3 esses eene 219 show tftp download software status sss 219 show tftp upload status sse eene 219 SHOW CLIN C eec a iter e erm ecce 220 show time parameters occ esses eee e eene nennen 220 SHOW tiImezone cse erede eee ree ee ra etr em P ore eee dana ern 221 SHOW rutilo A user s ERE e Pe a 221 show username cocococccooncnonononnconnnonnnonanocnnconnncnnn non nn noo no enhn ennt aie 222 SHOW vlan sisse IMG het end i eot tt oet eat reete ii s 222 show vlan Eayetr3 teneret ette as 223 show Web aux files url eese entente enne tnn nnne 223 ajo 224 ie KR MEM Ie p I 224 terminal length i de Rete ee eee 225 termina WATER re D PR A EE Dev Oe eH 225 timers DAS 2 oe ee oer c Poe eoe er erre vede eee rss e en ea esee Evan 225 tim rs OSPF i uentis aei reni e et et dba et meta iad 227 traceroute A ted e eet eet eed ei teet uc 228 pi TD 228 Username 3 5 etre eser e ear eser aea aen eva nero e eie ae e ane aveo Mete eria dee 229 validate group 2a at adea eto e oe dese t 230 validate policy list acs iia sees aee e eds 231 Avaya C460 Reference Guide ix Contents Layer CLI Commands utisia A E ete e dates 233 Layers CLI Commands 2nd Pee ada 237
135. ime is being acquired from server 0 0 0 0 Time has been acquired from the network hostname User level read write admin Use the hostname command to change the Command Line Interface CLI prompt The current module number always appears at the end of the prompt Use the no hostname command to return the CLI prompt to its default 34 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is no hostname lt hostname_string gt hostname_string e none displays current hostname string the string to be used as the hostname up to 20 characters Example C460 14 hostname Session hostname is C460 C460 1 hostname gregory C460 1 super If you wish to enter a name which includes spaces you must enclose the entire name in quotation marks for example new york hostname Layer 3 User level read write admin Changes the system prompt used for the router This command does not change the system prompt of the switch To change the system prompt of the switch use the host name command in the Layer 2 tree The syntax for this command is no hostname lt hostname_string gt hostname_string The string to be used as the hostname up to 20 characters If you do not enter a string the current hostname is displayed Example Router 1 gt hostname Marketing Marketing 1 If you wish to define a name which includes spaces you
136. in O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip access list name command to set a name for a policy list The syntax for this command is ip access list name lt policy list number gt lt name gt lt policy list number gt integer 100 to 149 policy 8 42 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands lt name gt list name Example C460 1 configure ip access list name 101 morning If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york ip access list owner ip address User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip access list owner command to set the owner for a specific policy list The syntax for this command is ip access list owner lt policy list number gt lt owner gt lt policy list number gt integer 100 to 149 lt owner gt list owner Example Router 1 ip access list owner 101 admin Done User level read write admin You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode Use the ip address command to assign an IP
137. into a physical address such as an Ethernet address The sender broadcasts an ARP request onto the TCP IP network The host whose IP address matches the requested address then replies with its physical hardware address Backbone A high bandwidth connection between switches A backbone link normally operates in Full Duplex Mode sending packets in both directions simultaneously Beacon Frame Refer to Beaconing Avaya C460 Reference Guide 241 Glossary Beaconing An error detection mechanism in Token Ring networks When a station detects a serious network problem it sends a Beacon Frame The Beacon Frame defines a failure domain that includes the station reporting the failure its nearest active upstream neighbor and everything in between Beaconing initiates a process in which the nodes in the failure domain perform diagnostics and attempt to reconfigure the network around the failed areas BGP Border Gateway Protocol An Internet protocol that enables groups of routers to share routing information so that efficient loop free routes can be established BOOTP Bootstrap Protocol An Internet protocol that enables a diskless workstation to discover its own IP address the IP address of a BOOTP server on the network and a file to be loaded into memory to boot the machine This enables the workstation to boot without a hard or floppy disk drive BPDU Bridge Protocol Data Unit A packet that is transmitted at configurab
138. ioHgDZZ2Z i10oHgD3D wD 32ZZ onD__ ZZ20AgD1 K9E YLN Y N ZZAo0jgD lt b lt Z gKgjiDZj Z1 NYROZN z WR E H n AgDwZZioHgDZZZZ ioHgD3D33D33ZZ onDwZZ20AgDN N ZZAOojgD 3Z gKgjiDZ xg glgi H n AgDwZZi0HgDZZZZ 10Hg9D3D33D wZZ onDQZZ20AgD A09E s 9s Os M ZZA0jgDw lt _Z gKgjiDZ AoZE s ZsOs MZ Zs ZY L s Neighbor SPV is not present 218 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show system log Layer 3 User level read only read write admin Displays the encrypted event log file The syntax for this command is show system log slot slot Slot number 1 to 2 show tftp download software status User level read only read write admin Use the show tftp download software status commands to display the status of the current TFTP Device Manager S W Embedded Web download process into the device The syntax for this command is show tftp download software status lt mod_num gt Example C460 1 gt show tftp download software status C460 1 gt Module 1 C460 1 gt C460 1 gt Module 1 C460 1 gt Source file d Np340swNgt m1N3 5 18Np340 web C460 1 Destination file EW Archive C460 1 Host 149 49 70 61 C460 1 gt Running state Writing C460 1 Failure display null C460 1 gt Last warning No warning show tftp upload status User level read only
139. ional TFTP server copy tftp SW_imageA lt filename gt lt ip gt filename file name including full path ip IP address of the host Example C460 1 copy tftp SW_imageA c imgA bin 149 49 36 200 Beginning download operation This operation may take a few minutes Please refrain from any other operation during this time KREKEKKKEKKK KKK KEKE KKK KKK K KKK KEKE KKK KKK KKK KKK KKK KKK KEKE KEKE KEK ck ck ck ck ko KKK ko ko ck ck ck ck ko ko ko ko Ax If you are currently running the C460 Device Manager application it is recommended to exit from it before performing configuration download operations kkxkxkxkxkxkxkxkkkkkkkxkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkxkkkkkkkkkkkxkxk copy tftp SW_imageB User level read write admin Use the copy tftp SW_imageB command to updates the software image in Bank B of all the Supervisor Modules installed in the switch To use this command you need to have an active TFTP server and to create a file into which to download the data If MSNM is running an additional tftp server is not required copy tftp SW_imageB lt filename gt lt ip gt filename file name including full path ip IP address of the host Example C460 1 copy tftp SW_imageB c imgB bin 149 49 36 200 Beginning download operation This operation may take a few minutes Please refrain from any other operation during this time ck ck KKK KKK KKK KKK KKK KK KKK KKK KKK KEK KKK KKK KEK KKK KKK
140. k status no link STA status Disabled Dk ckckckckckckckck ck ckck ck kckck ck ckckck kckck ck ck ck AS set port disable 5 6 set port auto negotiation flowcontrol advertisement 5 6 no flowcontrol set port negotiation 5 6 enable set port level 5 6 0 set trunk 5 6 off set port vlan 1 5 6 set port name 5 6 NO NAME set port trap 5 6 enable set port classification 5 6 valuable set port enable 5 6 TERK KKK ck kk ck ck ke kx ke ke x port 5 7 configuration okckckckck ckckck ck ck kck kckokok If Port type Tranceiver Not Present 4 Link status no link type q to quit or space key to continue STA status Disabled Dk ckckckckckckckck ck ckck ck ckckck ck ckckck ck ckck ck ck ck k AS set port disable 5 7 set port auto negotiation flowcontrol advertisement 5 7 no flowcontrol set port negotiation 5 7 enable set port level 5 7 0 set trunk 5 7 off set port vlan 1 5 7 set port name 5 7 NO NAME set port trap 5 7 enable set port classification 5 7 valuable set port enable 5 7 TERK KKK ck kk ck ck ko k ke ke x port 5 8 configuration okckckckck ckckckckck kck kck kk If Port type Tranceiver Not Present 4 Link status no link 4 STA status Disabled Jk ckckckckckckckck ck ckckck ck ckck ck ckckck k k k ck ckckck ck AS set port disable 5 8 set port auto negotiation flowcontrol advertisement 5 8 no flowcontrol set port negotiation 5 8 enable set port level 5 8 0 set trunk 5 8 off type q to quit or s
141. l read write admin O You can only access this command in Interface mode Typeinterface name atthe command prompt to enter Interface mode if necessary Use the ip ospf command to configure interface metric Usetheno ip ospf cost command to set the cost to its default The default is 1 The syntax for this command is no ip ospf cost cost cost integer Avaya C460 Reference Guide 51 Chapter 2 Avaya C460 CLI Commands Example Router 1 configure if marketing ip ospf cost 10 Done ip ospf dead interval User level read write admin You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip ospf dead interval command to configure the interval before declaring the neighbor as dead Use no ospf dead interval to set the dead interval to its default value of 40 The syntax for this command is no ip ospf dead interval seconds seconds Time in seconds integer value Example Router 1 configure if marketing 4 ip ospf dead interval 15 ip ospf hello interval User level read write admin O You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use this command to specify the time interval between hello s the router sends Useno ip ospf hello interval to set the hello interval to its default The defaul
142. lans 17 clear event log 18 clear interface 19 clear ip route 19 clear log 20 clear port mirror 20 clear port static vlan 21 clear power history 21 clear radius authentication server 21 clear screen 7 22 clear snmp trap 22 clear system log 23 clear timezone 23 clear vlan 24 configure 25 copy 12 config tftp 25 copy running config startup config 25 copy running config tftp 26 copy startup config tftp 26 copy tftp EW archive 27 copy tftp 12 config 27 copy tftp SW image 28 29 D disable interface 31 E enable interface 32 erase startup config 33 F fragment chain 33 G get time 34 H hostname 34 I ip access default action 37 ip access group 37 ip access list 38 ip access list cookie 39 ip access list copy 39 ip access list dscp operation 40 41 ip access list dscp precedence 41 ip access list dscp trust 42 ip access list dscp name 40 ip access list name 42 ip access list owner 43 ip simulate 61 N no banner login 15 no banner post login 15 no hostname 34 no rmon alarm 68 no rmon event 68 no rmon history 69 no username 69 nvram initialize 69 P ping 71 193 R reset 73 rmon alarm 75 rmon event 76 rmon history 76 S session 79 set allowed managers 80 set allowed managers ip 80 Avaya C460 Reference Guide 233 Layer 2 CLI Commands set arp aging interval 81 set arp tx interval 81 set boot bank 223 set broadcast storm control 82 set broadcast storm contr
143. lay a specific mac vlan in the CAM CAM table The syntax for this command is show cam mac lt mac gt lt vlan gt mac addr MAC address vlan VLAN identity Example C460 1 gt show cam mac 00 00 81 01 23 45 Dest MAC Route Destination Ports vlan 00 00 81 01 23 45 2 9 00 00 81 01 23 46 2 9 Total Matching CAM Entries 2 show cam vlan User level read only read write admin Use the show cam vlan command to display all MAC entries for a specific VLAN in the CAM The syntax for this command is show cam vlan lt vlan gt vlan VLAN identity Example C460 1 gt show cam vlan 3 Dest MAC Route Dest vlan Destination Ports Total Matching CAM Entries 2 Avaya C460 Reference Guide 147 Chapter 2 Avaya C460 CLI Commands show chassis identity User level read only read write admin Use the show module identity command to display the identifier s required for requesting license keys for this chassis The syntax for this command is show chassis identity Example C460 1 gt show chassis identity Chassis Identity 53333335 show copy status User level read only read write admin Usethe show copy status command to show the status of the local configuration copy operation The syntax for this command is show copy status Example C460 1 gt show copy status Module 1 Module id Source file rou
144. le intervals to exchange information among bridges in the network Among other things BPDUs inform the bridges of the topology of the network and detect loops and topology changes Broadcasting A common method of information transmission in which a packet is sent to every port on the network Bridge A device connecting two networks using similar protocols A bridge filters and forwards data between the networks according to their destination addresses Burst A transmission of data at a faster rate than normal Data bursts can be carried out in several ways A burst is always limited in time and can take place only under special conditions Bus A transmission path or channel A bus is typically an electrical connection with one or more conductors where all attached devices receive all transmissions at the same time 242 Avaya C460 Reference Guide Glossary BUS Broadcast and Unknown Server A multicast server used in ELANS that is used to forward multicast and broadcast traffic to the appropriate clients CAM Content Address Memory A list kept by each port containing the addresses of all network elements connected to the port CAM is accessed according to its contents not its memory address Chassis View Avaya Inc s Network Management System s graphic depiction of a network device Client A computer system or process that requests a service from another computer system or process a server Typic
145. le time between re authentication attempts The syntax for this command is set dotix re authperiod Seconds Seconds Idle time in seconds 0 to 65535 Example C460 1 super set dotix re authperiod 90 Done set dot1x server timeout User level supervisor Use the set dotix server timeout command to set the server retransmission timeout period for all ports This is the maximum time that the port will wait for a reply from the Authentication Server The syntax for this command is set dotix server timeout Seconds Seconds Timeout in seconds 0 to 65535 Example C460 1 super set dotlx server timeout 90 set dot1x supp timeout User level supervisor Use the set dotix supp timeout command to set the maximum time that the switch will wait for a reply from the Authenticated Station before the session is terminated Avaya C460 Reference Guide 85 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set dotix supp timeout lt Seconds gt Seconds Timeout in seconds 0 to 65535 Example C460 1 super set dotix supp timeout 90 set dot1x system auth control disable User level supervisor Use the set dotix system auth control disable command to globally disable the PBNAC 802 1x feature The syntax for this command is set dotix system auth control disable Example C460 1 super set dotix system auth control disable
146. level read only read write admin Use the show timezone command to display the current C460 time zone The syntax for this command is show timezone Example C460 1 gt show timezone Timezone set to GMT offset from UTC is 0 hours User level read only read write admin Use the show trunk command to display VLAN tagging information for the switch The syntax for this command is show trunk lt module gt lt port gt lt port module Number of the module If you do not specify a number all Optional modules are shown port Number of the port on the module If you do not specify a Optional number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Example C460 1 gt show trunk 4 1 Port Mode Binding mode Native vlan 41 1 off statically bound 1 41 2 dotlg statically bound 2 Output Fields Field Description Port Switch and port number s Avaya C460 Reference Guide 221 Chapter 2 Avaya C460 CLI Commands Mode Tag status of the port dot1q dot1O tagging mode off clear mode Binding mode Binding mode of the port Native VLAN Number of the Port VLAN ID the VLAN to which received untagged traffic will be assigned show username User level admin Use the show username command to display the local user accounts The syntax for this command is show usernam
147. ly access this command in Router OSPF mode Type router ospf at the command prompt to enter Router OSPF mode if necessary Use the redistribute command to redistribute routing information from other protocols into OSPF Use the no redistribute command disables redistribution by OSPF The syntax for this command is no redistribute lt protocol gt protocol static ospf Example Router 1 configure router ospf redistribute static redistribute RIP User level read write admin O You can only access this command in router RIP mode Type router rip at the command prompt to enter router RIP mode if necessary Usethe redistribute command to redistribute routing information from other protocols into RIP Usethe no redistribute command to disable redistribution by RIP 72 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands reset The default is disabled The syntax for this command is no redistribute lt protocol gt protocol Either Static or OSPF Example Router 1 configure router rip redistribute ospf Done User level read only read write admin Use the reset command to restart the system or an individual Supervisor module The syntax for this command is reset chassis spvs 1 2 chassis Reset the entire chassis including the Supervisor and I O Modules Reset the hardware Causes disruption to traffic of 10 to 20 seconds spvs Reset bot
148. mand is terminal width lt character gt character none Displays the current width in characters number Set the new screen width in characters Example C460 1 gt terminal width 80 terminal width 80 terminal length Use the terminal length command to set the length of the terminal display The syntax for this command is terminal length lt screen length gt screen length none Displays the current length in lines number Set the new screen length in lines Example C460 1 terminal length 25 6 Avaya C460 Reference Guide Chapter 1 Using the CLI clear screen Use the clear screen command to clear the current terminal display The syntax for this command is clear screen Example C460 1 gt clear screen Welcome to C460 SW version 1 0 0 C460 1 gt Avaya C460 Reference Guide 7 Chapter 1 Using the CLI Avaya C460 Sessions You can use sessions to switch between C460 Supervisor modules or to switch between Layer 2 and Layer 3 commands in the C460 CLI To switch between C460 modules use the command session lt mod_num gt lt mode gt The mod num is the number of the module in the chassis counting from the top down The mode can be either switch or router When Module Number is not specified the command switches between the modes in the local module Use switch mode to configure layer 2 commands Use router mode to confi
149. mand to display the ppp configuration The syntax for this command is show ppp configuration Example C460 1 gt show ppp configuration PPP baud rate is 38400 PPP incoming timeout is 15 minutes PPP Authentication Parameters Incoming None show ppp incoming timeout User level read only read write admin Use this show ppp incoming timeout command to display the amount of time in minutes that a PPP session can remain idle before being automatically disconnected The syntax for this command is show ppp incoming timeout Example C460 1 gt show ppp incoming timeout PPP incoming timeout is 15 minutes show ppp session User level read only read write admin Use the show ppp session command to display PPP parameters and statistics of an active PPP session The syntax for this command is show ppp session Example C460 1 gt show ppp session Avaya C460 Reference Guide 201 Chapter 2 Avaya C460 CLI Commands show radius authentication User level read only read write admin Use the show radius authentication command to display all RADIUS authentication configurations The syntax for this command is show radius authentication Example C460 1 gt show radius authentication RADIUS authentication parameters Mode Primary server Secondary server Retry number Retry time UDP port Shared secret Enab 92
150. ments that can comprise a single IP packet from 2 to 2048 The default is 64 Example C460 14 fragment chain 10 fragment size Use the fragment size command to set the maximum number of fragmented IP packets destined to the router to reassemble at any given time Use the no form of this command to set the fragment size to the default value 100 The router does not perform reassembly of packets in transit The syntax for this command is no fragment size lt database limit gt database limit The maximum number of packets undergoing re assembly at any given time from 0 to 200 The default is 100 Avaya C460 Reference Guide 33 Chapter 2 Avaya C460 CLI Commands Example Router 14 fragment size 150 fragment timeout Use the fragment timeout command to set the maximum number of seconds to reassemble a fragmented IP packet destined to the router Use the no form of this command to set the fragment timeout to the default value 10 The router does not perform reassembly of packets in transit The syntax for this command is no fragment timeout lt timeout gt timeout The maximum number of seconds to re assemble an IP packet from 5 to 120 The default is 10 Example Router 14 fragment timeout 30 get time Use the get time command to retrieve the time from the network The syntax for this command is get time Example C460 1 gt get time T
151. mmand Syntax Commands are not case sensitive That is uppercase and lowercase characters may be interchanged freely Command Abbreviations All commands and parameters in the CLI can be truncated to an abbreviation of any length as long as the abbreviation is not ambiguous For example version can be abbreviated ver For ambiguous commands type the beginning letters on the command line and then use the Tab key to toggle through all the possible commands beginning with these letters 4 Avaya C460 Reference Guide Chapter 1 Using the CLI Universal Commands Universal commands are commands that can be issued anywhere in the hierarchical tree Retstatus command Use the retstatus command to show whether the last CLI command you performed was successful It displays the return status of the previous command The syntax for this command is retstatus Example C460 1 set port negotiation 2 4 disable Link negotiation protocol disabled on port 2 4 C460 1 retstatus Succeeded Tree command The tree command displays the commands that are available at your current location in the CLI hierarchy The syntax for this command is tree Output Example Example C460 1 tree terminal width length Avaya C460 Reference Guide 5 Chapter 1 Using the CLI terminal width Use the terminal width command to set the terminal width of the terminal display The syntax for this com
152. mode command to enable learning of the default route received by the RIP protocol The default state is talk listen The syntax for this command is ip rip default route mode lt mode gt The possible default route modes on an interface are talk listen Set RIP to send and receive default route updates on the interface talk only Set RIP to send but not receive default route updates on the interface Example Router 1 configure if marketing ip rip default route mode talk listen Done ip rip poison reverse User level read write admin O You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode if necessary Usethe ip rip poison reverse command to enable split horizon with poison reverse on an interface Use theno ip poison reverse command to disable the poison reverse mechanism The split horizon technique prevents information about routes from exiting the router interface through which the information was received This prevents routing 56 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands loops Poison reverse updates explicitly indicate that a network or subnet is unreachable rather than implying they are not reachable Poison reverse updates are sent to defeat large routing loops The syntax for this command is no ip rip poison reverse Example Router 1 configure if marketing ip rip poison reverse Done
153. ncoming 122 set ppp baud rate 123 set ppp chap secret 123 set ppp incoming timeout 123 set radius authentication enable disable 124 set radius authentication retry time 125 set radius authentication secret 125 set radius authentication server 125 set radius authentication udp port 126 set slot power 126 set snmp community 128 set snmp retries 128 set snmp timeout 129 set snmp trap 129 set snmp trap auth 130 set spantree 131 set spantree priority 133 set system contact 134 set system location 135 set system name 135 set time client 136 set time protocol 136 set time server 137 set timezone 137 set trunk 138 set vlan 138 set web aux files url 139 set welcome message 140 show 234 Avaya C460 Reference Guide Layer 2 CLI Commands timezone 221 show access lists 140 show allowed managers status 141 show arp aging interval 142 143 show arp tx interval 143 show banner login 143 show banner post login 144 show boot bank 223 show broadcast storm control 144 show cam 145 show cam mac 147 show cam vlan 147 show copy status 148 show cpu load 149 show cs 149 show dev log file 153 show device mode 150 show dot1x 150 show dotl1x statistics 150 show dynamic vlans 151 show environment fans 151 show environment power 152 show erase status 153 show event log 153 show icmp redirect 154 show intelligent multicast 154 show interface 155 show ip access lists 156 show ip access group 155 show ip access lis
154. network address NSAP Network Service Access Point An ISO specified network address Avaya C460 Reference Guide 249 Glossary OID Object Identifier Used in SNMP to identify managed objects In the SNMP Manager Agent Network Management Paradigm each managed object must be identified by a unique OID OSI Open Systems Interconnection reference model A model for network communications consisting of seven layers that describe what happens when computers communicate with one another OSPF Open Shortest Path First A routing protocol featuring least cost routing multipath routing and load balancing Out of Band Transmission of auxiliary information such as management messages using frequencies or channels outside the frequencies or channels normally used for information transfer Out of band signaling is often used for error reporting in situations in which in band signaling can be affected by whatever problems the network might be experiencing Packet Logical grouping of information that includes a header containing control information and usually user data Packets are most often used to refer to application layer data units PING Packet Internet Groper Determines whether a specific IP address is accessible by sending a packet to the specified address and waiting for a reply Plus Tagging A proprietary Avaya tagging mechanism that enables extended VLAN capabilities POP Post Office Protocol Used to
155. next hop The next hop address in the network cost The path cost The default is 1 preference Preference either High or Low Default is Low Example To define the router 192 168 33 38 as the next hop for the network 192 168 33 0 with mask 255 255 255 0 C460 1 configure ip route 192 168 33 0 255 255 255 0 10 10 10 10 ip routing User level read write admin You can only access this command in configure mode Type configure at the command prompt to enter configure mode Avaya C460 Reference Guide 59 Chapter 2 Avaya C460 CLI Commands Use the ip routing command to enable IP routing Use the no ip routing command to disable the IP routing process in the device By default IP routing is enabled The syntax for this command is no ip routing Example C460 1 configure ip routing Done ip routing mode User level read write admin O You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode if necessary Usethe ip routing mode command to set the IP routing mode of the interface In RT MGMT mode the interface functions as a routing interface In RT PRIMARY MGMT mode the interface function as both a routing interface and the primary management interface The IP address used in MSNM is the primary management interface IP address Only one interface can be in RT PRIMARY MGMT mode If no interface is configured
156. nnrnrnararnnancnnnnoso 37 Ip access erOup a his etie eee e eer eee e e eee 37 Ip dccess list menn eee emt erede eere Dilecte tei nes 38 ip access list cookie aote ef ee eie nte t tease 39 ip access list COopy ee orense eeaeee iaaeaie naina aeaee aee Ekaa 39 ii Avaya C460 Reference Guide Contents ip access list dscp name desia iE eio e eE aT EE 40 ip access list dscp operation sse 40 ip access list dscp precedence cecococononononnrncnnennnnencnnorannnnnnnrararnnnonaranarnanoss 41 ip access list dscp trust sse 42 E NAAA den ner tees 42 ip ccess lHist OWTIer Li eoe eee etit eem rre eme ettet 43 ip address cete AL ells ect UR itle bale E a deer este 43 A NS 44 ip bootp dhep rietwork AA tr teens 44 ip bootp dhep relay ertet eb iet ee etie etis 45 ip bootp dhcp Servers oeste ede ded edente 46 ip broadcast address zerorri ai innesa eienen sianet Eekan iEn 46 Ip dela Ult ZA WAY eccessi tinin uni tuer A E S 47 ip directed broadcast eienn i i eee eene 47 Up MCI sivo d X 48 ip max arp entries oo eeececccsseecsseecseeecseeeeseseseseseeeeeeseecseseesceeeceeseneees 48 ip max route entries coococccncconcnnonnnnononnnnnnnononnnannnn anno ENEE 49 ip netbios rebroadcast emccococenonencnnoncncnnenernnnnnennnnrnnnnranannnnnnn ra rnnnnraranaronnanoso 49 ipmetmask format sismi tiist hoe caves etre tete baee chet dista 50 ip ospf authentication key sese nenne 51 Ip OSDE COSE on
157. ns_module_fault fans_module_fault_return Avaya C460 Reference Guide 211 Chapter 2 Avaya C460 CLI Commands show snmp retries User level read only read write admin Use the show snmp retries command to display the number of retries initiated by the C460 Manager when it tries to send SNMP messages to the device The syntax for this command is show snmp retries Example C460 1 gt show snmp retries the SNMP Retries Number is 3 show snmp timeout User level read only read write admin Use the show snmp timeout command to display the default SNMP timeout in seconds O This command is useful for access using the Device Manager The syntax for this command is show snmp timeout Example C460 1 gt show snmp timeout the SNMP Timeout is 2000 show spantree User level read only read write admin Use then show spantree command to display spanning tree information The syntax for this command is show spantree lt module gt lt port gt module Number of the module If you do not specify a number all Optional modules are shown port Number of the port on the module If you do not specify a Optional number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 212 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands
158. nts An AppleTalk socket is similar in concept to a TCP IP port Spanning Tree Protocol Refer to STA on page 253 STA Spanning Tree Algorithm The algorithm used by the Spanning Tree Protocol to create a spanning tree The Spanning Tree Protocol STP is a bridge protocol that uses the STA to enable a learning bridge to dynamically work around loops in a network topology by creating a spanning tree Bridges exchange BPDU messages with other bridges to detect loops and then remove the loops by shutting down Avaya C460 Reference Guide 253 Glossary selected bridge interfaces Stack A layered set of protocols which work together to provide a set of network functions Each intermediate layer uses the layer below it to provide a service to the layer above Standalone Mode An option to separate a module from the other modules in a device so that its bus is independent This may be desirable for example if one module has exceptionally heavy traffic that might affect other modules Subnet Short for subnetwork A subnet is a portion of a network that shares a common address component On TCP IP networks a subnet includes all devices whose IP addresses have the same prefix For example all devices with IP addresses that start with 133 100 100 are part of the same subnet Subnet Mask A 32 bit address mask used in IP to indicate the bits of an IP address that are being used for the subnet address Switch A device that fil
159. o Security Levels on page 9 Application context used as body of the prompt this part is not mandatory Example Host name of the router is London Router is module number three Application context is OSPF Avaya C460 Reference Guide Chapter 1 Using the CLI The command line prompt looks as follows London 1 configure router ospf The command prompt is not hierarchical in structure If you wish to use several commands each beginning with the same keyword you must retype all parts of the command each time For example if after you want to set the system contact and the system name you must type both set system contact and set system name However you can use command abbreviations Avaya C460 Reference Guide 3 Chapter 1 Using the CLI Navigation Cursor Movement and Shortcuts The CLI contains a simple text editor with these functions Table 1 1 Navigation Cursor Movement and Shortcuts Keyboard Functions Backspace Deletes the previous character Up arrow Down arrow Scrolls back and forward through the command history buffer Left arrow Right arrow Moves the cursor left or right Tab Completes the abbreviated command Type the minimum number of characters unique to the command An exception is the Reset System command which you must type in full Enter Executes a single line command 11044 If you type a name with quotation marks the marks are ignored Co
160. o banner post login command to set the post login banner to the default value O Before creating a new banner delete the current banner using the no banner post login command Avaya C460 Reference Guide 15 Chapter 2 Avaya C460 CLI Commands The syntax for this command is no banner post login Example C460 1 super banner post login C460 1 super banner post login line See line clear arp cache User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the clear arp cache command to delete dynamic entries from the ARP cache and the IP route cache The syntax for this command is clear arp cache lt vlan gt ip addr mask vlan VLAN string up to 16 characters ip addr IP address mask IP mask Example Cc460 1 configure clear arp cache Flushing all arp entries Flushed 100 ARP entries Done 16 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands clear cam User level read write admin Use the clear cam command to delete all entries from the CAM table The syntax for this command is clear cam Example C460 14 clear cam CAM table cleared clear dot1x config User level privileged supervisor Use the clear dot1x config command to disable dot1x on all ports and return
161. o be aggregated in the format module port value e on enable a channel for the specified module port e off disable a channel for the specified module port name channel name Optional If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york Example C460 1 set port channel 4 6 18 on server2 Port 4 6 channel mode set to on Port 4 18 was added to channel set port classification User level read write admin Use the set port classification command to set the port classification to either regular or valuable Any change in the Spanning Tree state from Forwarding for a valuable port will erase all learnt MAC addresses in the switch The syntax for this command is set port classification module port regular valuable module port module port range regular valuable port classification Example C460 1 set port classification 2 19 valuable Port 2 19 classification has been changed 100 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set port disable User level read write admin Use the set port disable command to disable a port or range of ports The syntax for this command is set port disable module gt lt port module Number of the module 3 6 If you do not specify a number the ports on all the modules are shown port Number of the port on the module If you do not specify a number
162. o negotiation If negotiation is disabled the user can set the speed and duplex of the Fast Ethernet Avaya C460 Reference Guide 111 Chapter 2 Avaya C460 CLI Commands ports The syntax for this command is set port negotiation lt module gt lt port gt enable disable module Number of the module 3 6 If you do not specify a number the ports on all the modules are configured port Number of the port on the module If you do not specify a number the negotiation is set for all the ports on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 enable Enable port negotiation protocol disable Disable port negotiation protocol Example To disable autonegotiation on port 1 module 4 C460 1 set port negotiation 4 1 disable Link negotiation protocol disabled on port 4 1 set port point to point admin status User level read write admin Use the set port point to point admin status command to set the port RSTP point to point admin status The syntax for this command is set port point to point admin status lt module port gt lt admin status gt module Number of the module 3 6 If you do not specify a number the ports on all the modules are configured port Number of the port on the module If you do not specify a number the negotiation is set for all the ports on the module You can also specify a range of ports separate
163. o turn the ICMP error messages on C460 1 configure ip icmp errors Done ip max arp entries User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip max arp entries command to set the maximum number of ARP cache entries allowed in the ARP cache Use the no ip max arp entries command to restore the default value of 4096 This command takes effect only after start up The syntax for this command is no ip max arp entries value value The space available for the IP address table When you decrease the number of entries it may cause the table to be relearned more frequently If you do not enter a value then the current ARP Cache size is shown Example To set the maximum number of ARP cache entries to 8000 C460 1 configure ip max arp entries 8000 48 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands To restore the maximum number of ARP cache entries to its default C460 1 configure no ip max arp entries ip max route entries User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode The ip max route entries command exists for compatibility with Avaya P580 There is no limitation
164. of the links The syntax for this command is set port redundancy lt module gt lt prim_port gt lt module gt second port on off lt redundancy_name gt prim_port Primary port of the redundancy scheme second_port Secondary port of the redundancy scheme redundancy_name Name for the redundancy scheme Optional Example C460 1 set port redundancy 3 7 4 12 on red1 redi Port 2 12 is redundant to port 1 7 Port redundancy is active entry is effective immediately If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york set port redundancy intervals User level read write admin Use the set port redundancy intervals command to configures the two time constants that determine redundancy switchover parameters e Min Time between switchovers is the minimum interval between switchover of each pair e Switchback interval is the period the primary port link has to be up before the system switches back If the switchback interval is zero the system never switches back If it is one switchback occurs immediately after the primary port link returns Avaya C460 Reference Guide 115 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set port redundancy intervals lt min time between switchovers gt lt switchback interval gt none min time between switchovers switchback interval none Ex
165. ol threshold 83 set device mode 83 set dotlx max req 84 set dot1x quiet period 84 set dot1x re authperiod 85 set dot1x server timeout 85 set dotlx supp timeout 85 set dot1x system auth control disable 86 set dot1x system auth control enable 86 set dot1x tx period 87 set inband vlan 88 set intelligent multicast 88 set intelligent multicast client port pruning time 88 set intelligent multicast group filtering delay time 89 set intelligent multicast router port pruning time 89 set interface inband 90 set interface outband 90 set interface ppp 91 set interface ppp enable disable off reset 91 set ip route 92 set license 94 set logout 94 set mac aging 95 set mac aging time 95 set outband duplex 186 set outband negotiation 96 set outband speed 97 set port auto negotiation flowcontrol adver tisement 99 set port channel 99 set port classification 100 set port disable 101 set port dot1x initialize 101 set port duplex 106 set port flowcontrol 109 set port level 110 set port mirror 110 set port name 111 set port negotiation 111 set port powerinline 113 set port powerinline priority 113 set port redundancy 114 set port redundancy on off 115 set port redundancy intervals 116 set port spantree 116 set port spantree cost 117 set port spantree priority 118 set port speed 118 set port static vlan 119 set port trap 119 set port vlan 120 set port vlan binding mode 121 set ppp authentication i
166. on Example show ip arp Display all ARP mapping show ip arp marketing Display interface ARP mapping show ip arp 192 168 49 1 Display one host ARP mapping show ip arp 192 168 49 1 255 255 255 0 Display range of ARP mapping show ip arp marketing_vlan Display vlan ARP mapping show ip arp static Display static ARP mapping show ip icmp If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york User level read only read write admin Use the show icmp ip command to display the status of ICMP error messages The syntax for this command is show ip icmp Example Router 1 gt show ip icmp ICMP error messages status is ENABLE 158 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show ip interface User level read only read write admin Use the show ip interface command to display information for an IP interface The syntax for this command is show ip interface lt interface name gt lt ip address gt lt vlan gt interface name The name of the interface whose information you want to display ip address The IP address of the interface whose information you want to display vlan The name or ID of the VLAN over which there are interfaces you want to display Example Router 1 gt show ip interface Showing 2 Interfaces mgmt is administratively up On vlan Default Internet address is 10 49 54 1
167. on at a time between sending and receiving stations For more information refer to Duplex Mode on page 244 HDX Half Duplex A circuit or device permitting data transmission in only one direction at a time between sending and receiving stations For more information refer to Duplex Mode on page 244 Hop Passage of a data packet between two network nodes for example between two routers Avaya C460 Reference Guide 245 Glossary Host A computer attached to a network that provides services to another computer beyond simply storing and forwarding information HTTP Hyper Text Transmission Protocol The protocol used between clients and servers on the World Wide Web for transmission of HTML documents Hub A common connection point for devices in a network Hubs are commonly used to connect segments of a LAN IANA Internet Assigned Numbers Authority The organization responsible for assigning new Internet wide IP addresses ICMP Internet Control Message Protocol An extension to the Internet Protocol IP ICMP supports packets containing error control and informational messages IEEE Institute of Electrical and Electronics Engineers Among other things the IEEE develops standards for the computer and electronics industry In particular the IEEE 802 LAN standards are widely followed IEEE 802 3 IEEE standard for Ethernet LANs IEEE 802 5 IEEE standard for Token Ring LANs IMAP Internet Messa
168. on the size of the routing table except for the amount of available memory Use the no ip max rout ntries command to remove the limitation The syntax for this command is no ip max route entries lt value gt value number of entries Example C460 1 configure ip max route entries 4000 ip netbios rebroadcast User level read write admin O You can only access this command in interface mode Typeinterface name atthe command prompt to enter interface mode Usethe ip netbios rebroadcast command to set the NETBIOS rebroadcasts mode on an interface Usetheno ip netbios rebroadcast command to disable NETBIOS rebroadcasts on an interface The syntax for this command is no ip netbios rebroadcast mode Avaya C460 Reference Guide 49 Chapter 2 Avaya C460 CLI Commands The possible values of mode are both Netbios packets received on the interface rebroadcasted to other interfaces and netbios packets received on other interfaces are rebroadcasted into this interface disable Netbios packets are not rebroadcasted into or out of this interface Example To enable rebroadcasting of netbios packets received by and sent from the interface marketing Router 1 config if marketing ip netbios rebroadcast both ip netmask format User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at th
169. or Module The syntax for this command is clear system log lt module_number gt spv_num Number of Supervisor Module 1 to 2 Optional Example C460 1 clear system log Clearing the reset file do you want to continue Y N y C460 1 clear timezone User level read write admin Use the clear timezone command to reset the time zone to its default value UTC Coordinated Universal Time The syntax for this command is Clear timezone Example C460 1 clear timezone Timezone name and offset cleared Avaya C460 Reference Guide 23 Chapter 2 Avaya C460 CLI Commands clear vlan User level read write admin Use the clear vlan command to delete an existing VLAN and return ports from this VLAN to the default VLAN 1 When you clear a VLAN all ports assigned to that VLAN are assigned to the default VLAN 1 The syntax for this command is clear vlan lt vlan id gt name lt vlan_name gt vlan id VLAN number vlan name VLAN name If you wish to enter a name which includes spaces you must enclose the entire name in quotation marks for example new york Example C460 1 clear vlan 100 This command will assign all ports on vlan 100 to their default in the entire management domain do you want to continue Y N y VLAN 100 deletion successful clear vlan Layer 3 User level read write admin O If you are at the read write user l
170. outband 5 1 4 The snmp community strings set snmp community read only public set snmp community read write public set snmp community trap public set system location set system name set system contact set logout 0 Avaya C460 Reference Guide 175 Chapter 2 Avaya C460 CLI Commands E Set vlan table management parameters E set vlan 1 name V1 E 4 Set the interface of the device E 4 set interface inband 1 149 49 50 233 E Set PPP management parameters E set interface ppp 0 0 0 0 0 0 0 0 type q to quit or space key to continue set interface ppp disable set ppp authentication incoming none set ppp incoming timeout 0 set ppp baud rate 38400 E 14 Set Rmon History entries Id Id Set Rmon Alarms 1d 1d Set Rmon Events 1d Id Set embedded web management parameters 1d set snmp retries 3 set snmp timeout 2000 set web aux files url www avaya com Id Set radius management parameters Id set radius authentication disable type q to quit or space key to continue set radius authentication server 0 0 0 0 primary set radius authentication server 0 0 0 0 secondary set radius authentication retry number 4 set radius authentication retry time 5 set radius authentication udp port 1812 E 255 255 255 0 176 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands g set set set set set s
171. owing message is displayed Auto negotiation is Enable can not set the speed mode The syntax for this command is set outband speed lt speed gt speed 10MB e 100MB Example C460 1 set outband speed 100MB Speed for outband port set successfully set policy type User level read write admin Use the set policy type command to set whether the C460 switch enforces the active policy list on all packets or only on routed packets in device mode router Avaya C460 Reference Guide 97 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set policy type lt value gt all router value all apply policy to all packets entering the C460 through Fast Ethernet ports router apply policy on routed packets only Example Router 14 set policy type all 98 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set port auto negotiation flowcontrol advertisement User level read write admin Use the set port auto negotiation flowcontrol advertisement command to set the flowcontrol advertisement for a Gigabit port when performing autonegotiation The syntax for this command is set port auto negotiation flowcontrol advertisement lt module gt lt port gt mode module Number of the module 3 6 port Number of the port on the module If you do not specify a number all the ports on the module are set You can also specify a range of ports sepa
172. p filtering delay time lt seconds gt seconds The time in seconds Example C460 1 set intelligent multicast group filtering delay time 40 Done set intelligent multicast router port pruning time User level read write admin Usetheset intelligent multicast router port pruning time command to set aging time for router ports The syntax for this command is set intelligent multicast router port pruning time seconds seconds The time in seconds Example C460 1 set intelligent multicast router port pruning time 40 Done Avaya C460 Reference Guide 89 Chapter 2 Avaya C460 CLI Commands set interface inband User level read write admin Use the set interface inband command to configure the inband interface on the Supervisor Module The syntax for this command is set interface inband lt vlan gt lt ip_addr gt lt netmask gt vlan The number of the VLAN to be assigned to the interface ip_addr IP address netmask Subnet mask Example To configure the inband interface on VLAN 1 IP address 1 1 1 1 and netmask 255 255 255 0 C460 1 set interface inband 1 1 1 1 1 255 255 255 0 This command will RESET the device Reset do you want to continue Y N y set interface outband User level read write admin Use the set interface outband command to configure the outband interface on the supervisor Module The syntax for this command is set inter
173. pace key to continue set port vlan 1 5 8 set port name 5 8 NO NAME set port trap 5 8 enable set port classification 5 8 valuable set port enable 5 8 180 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands LER KK ck k ck k ck ck KKK KKK port 5 9 configuration ockckckckckckckckckck kck kc k KE Port type Tranceiver Not Present 4 Link status no link STA status Disabled p fp kK KK ck ckck ck ckckck k ckckck ck ck ck ck k k ck k ck ck ck k AS set port disable 5 9 set port auto negotiation flowcontrol advertisement 5 9 no flowcontrol set port negotiation 5 9 enable set port level 5 9 0 set trunk 5 9 off set port vlan 1 5 9 set port name 5 9 NO NAME set port trap 5 9 enable set port classification 5 9 valuable set port enable 5 9 LER KK ck k ck KKK KKK ck ke port 5 10 configuration ockckckckckckckckckck kck kc k ck ok type q to quit or space key to continue Port type Tranceiver Not Present 4 Link status no link STA status Disabled p HER RRR KKK KK KK KK KK KK KK KK KK KK KK KK KK KK KK KK KK KK KK KK CK Kk Kk k k k k k k KK KK set port disable 5 10 set port auto negotiation flowcontrol advertisement 5 10 no flowcontrol set port negotiation 5 10 enable set port level 5 10 0 set trunk 5 10 off set port vlan 1 5 10 set port name 5 10 NO NAME set port trap 5 10 enable set port classification 5 10 valuable set port enable 5 10 LPR KK KKK ck ck ck ck ck k
174. packets which failed to be reassembled is 0 Number of packets which overflowed the database is 0 show icmp redirect User level read only read write admin Use the show icmp redirect command to display whether ICMP redirects are accepted or rejected The syntax for this command is show icmp redirect Example C460 1 gt show icmp redirect icmp redirect is accepted show image version User level read only read write admin See show spo show intelligent multicast User level read only read write admin Use the show intelligent multicast command to display the intelligent multicast configuration 154 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is show intelligent multicast Example Intelligent multicast intelligent multicast Intelligent multicast Intelligent multicast intelligent multicast C460 1 gt show intelligent multicast configuration State Disabled client port pruning time 600 Sec router port pruning time 1800 Sec group filtering delay time 10 Sec show interface User level read only read write admin Use the show interface command to display information on network interfaces The syntax for this command is show interface Example C460 1 gt show interface Interface Name Status VLAN IP address Netmask inband disabled T 135 64 200 105 25572557255
175. permits traffic to be routed from one network to another on the basis of the intended destinations of that traffic A router located in a server is called an internal router a router located in a workstation is called an external router Routing Table A table stored in a router or other internetworking device that keeps track of routes to particular network destinations and in some cases metrics associated with those routes SAP Service Advertising Protocol A protocol used to identify the services and addresses of servers attached to the network The responses are used to update a table in the router known as the Server Information Table SAP is primarily used in Novell NetWare operating systems in conjunction with IPX Segmentation Segmentation is a common solution to LAN bandwidth limitations The LAN is divided into separate LAN segments using bridges and routers If segmented correctly most network traffic will remain within a single segment enjoying the full 10 Mbps bandwidth Hubs and switches are used to connect each segment to the rest of the LAN Side Band Transmission of auxiliary information such as management messages by means of a direct connection that bypasses the frequencies and channels normally used for information transfer Unlike out of band transmission side band transmission does not require a modem 252 Avaya C460 Reference Guide Glossary SLIP Serial Line Internet Protocol SLIP is the
176. ption Mode enabled of times Master 1 of received Advertisements 0 of transmitted Advertisements 13 of received Advertisements with Security Violations 0 172 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show 12 config User level read write admin Use the show 12 config command to display comprehensive Layer 2 configuration information The syntax for this command is show 12 config Example C460 1 show 12 config EHE FEAE FE HE FE FE HE FE AE FE HE FE HE FE FE FE FE HE FE HE FE FE FE FHE HE FE FE FE FE FE FE FE FE FE FE FE HE HE FE FE FE HE FHE HE FE HE HE HE HE FHE HE FE HE HE FHE HE FHE HE HE FE HE FHE HE HE HE HEHE HE CHASSIS INFO 1 AE FE AE FE HE FE FE AE FE HE FE HE EEE HE HE FE FE FE FE HE FE EHH FHE HE FE FE FE FE HE FHE HE FE HE HE FHE HE FE HE HE HE HE FHE HE HE HE HE FHE HE FHE HE HE E HE FHE HE FE HE HE HE HE HE EEE Upload time UPTIME 0 05 44 533 System description Avaya Inc C460ML SW Multi layer Switch 4 Inband MAC address 00 04 0d 17 20 00 Outband MAC address 00 04 0d 17 20 fe 4 Inband IP address netmask 149 49 50 233 255 255 255 0 Outband IP address netmask 0 0 0 0 0 0 0 0 Active SPV position 1 Number of blades 2 I Backplane CS 0 3 type q to quit or space key to continue Backplane Serial 0000019 Avaya C460 Reference Guide 173 Chapter 2 Avaya C460 CLI Commands
177. r after a reboot or after opening a new session see session command in the stack The syntax for this command is set welcome message string string string the string to be used as the welcome message blank Restores the default string Example C460 1 set welcome message avaya The new welcome string is avaya If you wish to define a string which includes spaces you must enclose the entire string in quotation marks e g new york show access lists User level user privileged supervisor Use the show access lists command to display all the current policy lists The syntax for this command is show access lists lt policy list number gt policy list number The policy list number integer from 100 to 199 0 is th default list 140 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example Router 1 gt show access lists The current policy source is local default List 0 parameters List Owner other ist 0 is valid default action for list 0 is permit show allowed managers status User level read only read write admin Use the show allowed managers status command to display the activation status of the Allowed Managers feature The syntax for this command is show allowed managers status Example C460 1 super show allowed managers status Managers are disabled Avaya C460 Reference Guide 141 Chapter
178. r 2 Avaya C460 CLI Commands clear interface User level read write admin Use the clear interface command to clear the inband or outband interface from the NVRAM The syntax for this command is clear interface outband inband outband Clears the outband interface inband Disables the inband interface Example C460 1 clear interface outband Interface outband Cleared You must reset the device in order for the change to take effect clear ip route User level read write admin Use the clear ip route command to delete IP routing table entries The syntax for this command is clear ip route destination mask destination IP address of the network or specific host to be added mask IP address of the router Example C460 14 clear ip route 134 12 3 0 255 255 255 0 Route deleted clear ip route Layer 3 User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Avaya C460 Reference Guide 19 Chapter 2 Avaya C460 CLI Commands Use the clear ip route command to delete all the dynamic routing entries from the Routing Table The syntax for this command is clear ip route lt ip addr gt lt ip mask gt ip addr IP address ip mask IP mask address Example C460 1 configure clear ip route 192 168 49 1 255 255 255 0
179. r level read write admin O You can only access this command in Interface mode Typeinterface name atthe command prompt to enter Interface mode if necessary Use the ip vrrp timer command to set the virtual router advertisement timer value in seconds for the virtual router ID Useno ip vrrp timer command to restore the default value The syntax for this command is no ip vrrp vr id timer value vr id Virtual Router ID 1 255 value The advertisement transmit time seconds Example To set the virtual router advertisement timer value for virtual router 3 to 2 Router 1 configure if marketing ip vrrp 3 timer 2 Done You can only access this command from the banner or post login banner context Use the 1ine command to add a line to the banner or post login banner message The syntax for this command is line number string number Line number in the banner 1 to 24 string String to be displayed at the given line number up to 80 characters 66 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 super line 5 C460 CLI Done network RIP User level read write admin O You can only access this command in router RIP mode Type router rip at the command prompt to enter router RIP mode if necessary Use the network command to specify a list of networks on which the RIP is running Use the no network command to remove an en
180. r router Example Router 1 configure router rip timers basic 30 180 User level read write admin O You can only access this command in Router OSPF mode Type router ospf at the command prompt to enter Router OSPF mode if necessary Use the timers spf command to set the delay between runs of OSPF SPF calculation Use the no timers spf command to restore the default 3 seconds The syntax for this command is no timers spf lt spf holdtime gt spf holdtime The time in seconds of the delay between runs of OSPF s SPF calculation Example Router 1 configure router ospf timers spf 5 Done Avaya C460 Reference Guide 227 Chapter 2 Avaya C460 CLI Commands traceroute User level read only read write admin Provides a trace route utility The syntax for this command is traceroute lt host gt host IP address Example Router 1 gt traceroute 192 168 50 13 tree User level read only read write admin Use the tree command to display a list of CLI commands available at the current user level The syntax for this command is tree lt depth gt depth Depth of CLI commands displayed 228 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example show show show show show show show show show show show show show show show show show show show C460 session terminal width terminal length clear s
181. rap 5 3 enable set port classification 5 3 valuable set port enable 5 3 TERK KKK KKK KKK KK ke port 5 4 configuration KKK KKK KKK ck ck ckck kc kckok Port type Tranceiver Not Present 4 Link status no link STA status Disabled pk kck ck ckckck ck ckck k ckckck k ck kck ck kck k ck ck ck k AS type q to quit or space key to continue set port disable 5 4 set port auto negotiation flowcontrol advertisement 5 4 no flowcontrol set port negotiation 5 4 enable set port level 5 4 0 set trunk 5 4 off set port vlan 1 5 4 set port name 5 4 NO NAME set port trap 5 4 enable set port classification 5 4 valuable set port enable 5 4 LPR KK ck k ck k ck ck KKK KKK port 5 5 configuration ockckckckckckckckckck kck ckck ck k Port type Tranceiver Not Present 4 Link status no link STA status Disabled I fp kK KK ck ckck k ck ckck k ck ck ck k ck KR k kck k k ck ck AS set port disable 5 5 set port auto negotiation flowcontrol advertisement 5 5 no flowcontrol set port negotiation 5 5 enable set port level 5 5 0 set trunk 5 5 off set port vlan 1 5 5 set port name 5 5 NO NAME type q to quit or space key to continue set port trap 5 5 enable set port classification 5 5 valuable set port enable 5 5 Avaya C460 Reference Guide 179 Chapter 2 Avaya C460 CLI Commands LPR KK ck ck KK KK RK KKK port 5 6 configuration okckckckck ckckckckck kck kck kk If Port type Tranceiver Not Present 4 Lin
182. rated by a dash for example 4 5 13 for ports 5 to 13 on module 4 mode no flowcontrol the port will advertise no pause capabilities asym tx only the port will advertise asymmetric Tx pause capabilities only sym only the port will advertise symmetric pause capabilities only e sym and asym rx the port will advertise both symmetric and asymmetric Rx pause capabilities Example C460 1 set port auto negotiation flowcontrol advertisement 2 5 asym tx only Port 2 5 pause capabilities was set set port channel User level read write admin Enables or disables a Link Aggregation Group LAG interface on the switch LAG creation requires a LAG name to be specified There is no default name You can also add or remove a port from an existing LAG All ports in the LAG are configured with the parameters of the first port that is added to the LAG These parameters include port administrative status speed duplex autonegotiation mode VLAN ID tagging mode binding mode and priority level When adding a port to an existing LAG the user must type the same LAG name or no LAG name Avaya C460 Reference Guide 99 Chapter 2 Avaya C460 CLI Commands otherwise you will get an error message O When adding a port to an existing LAG type the same LAG name otherwise you will create a new LAG The syntax for this command is set port channel lt port_list gt value name port_list A list of ports t
183. re tet 126 set slot power priority cene reete cete teet enne 127 set snmp community oo ccccccccccseeccesecsenecsenecsenecsensesensessnsesenecsenecsensesees 128 Set SAMP TEES ult Hoe rd tuts 128 set snmp timeout narraire inaianei three nennen 129 setsimp rap eere edem ee eee ene eee deer 129 Set SMM p trap auth x un eee ertet e eee pete rt bee Pede 130 set spantree default path cost sssesssssssseeeeneeenes 131 set spantree enable disable sse 131 set spantree forward delay sssssssssssesssssseeeeee 132 set spantree hello time esee eee eee nenne 132 set spantree max age eiue deiken iens Eda a NRE EENE conan nnne 132 set spantree priority sse eene nennen 133 set spantree tx hold count sse 133 set spantree version ecconoocononoononnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnnrnnnnnnnrnnnnns 134 Set Systeri contact ssepe dtt ipai 134 s t system loca n d i iue e ee RT egal 135 setsystem name ose eee ee eee estne eee 135 SOE time client e ere tertie ese Do e v ae eee ET Ee rette don 136 setitime protocol al tee eee fe hia 136 Set mme Server 5 oec eee ee RI Ue EE P E REOR Rel 137 vi Avaya C460 Reference Guide Contents set TIMEZONE 3 5 crie tie ee bed eder lees ai e eee teer re rd ERE 137 SEU NTN e 138 SEL VIAN opti Ho uto Neto Gen hien tier BAG AL LA 138 set Vian Layer o dee nee t ess 139 set web aux files url
184. read write admin Use the show tftp download status and show tftp upload status commands to display the status of the current TFTP configuration file copy process into from the device The syntax for this command is show tftp download upload status lt mod_num gt Avaya C460 Reference Guide 219 Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show tftp upload status 1 Module sor Source file C460 config Destination file c conf cfg Host 149 49 36 200 Running state Executing Failure display null Last warning No warning show time User level read only read write admin Use the show time command to display the current C460 time and timezone The syntax for this command is show time Example C460 1 gt show time 10 32 34 27 JAN 2000 GMT show time parameters User level read only read write admin Use the show time parameters command to display the time status and parameters The syntax for this command is show time parameters Example C460 1 gt show time parameters Client status Enabled Current time L 00 57 19 01 JAN 1970 GMT Timezone set to GMT offset from UTC is 0 hours Time Server 0 0 0 0 I e broadcast address Time acquired from Time Server 0 0 0 0 Time protocol set to TIME protcol 220 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show timezone show trunk User
185. rface name atthe command prompt to enter interface mode Use the ip vlanandip vlan name commands to specify the VLAN on which an IP interface resides You can specify either the VLAN ID using the ip vlan command or the VLAN name using the ip vlan name command Theno ip vlanorno ip vlan name command to reset the IP interface to the Avaya C460 Reference Guide 61 Chapter 2 Avaya C460 CLI Commands ip vrrp default VLAN The syntax for this command is no ip vlan vlan id Example To specify VLAN developmental as the VLAN used by interface products Router 1 config if marketing ip vlan name development If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york User level read write admin O You can only access this command in Interface mode Typeinterface name atthe command prompt to enter Interface mode if necessary Usethe ip vrrp command to create a virtual router on the interface Use the no ip vrrp command to delete a virtual router The syntax for this command is no ip vrrp lt vr id gt vr id Virtual Router ID 1 255 Example Router 1 configure if marketing 4 ip vrrp 1 Done ip vrrp address User level read write admin O You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip vrrp address
186. rt vlan binding mode 5 2 static set port vlan binding mode 5 3 static set port vlan binding mode 5 4 static set port vlan binding mode 5 5 static set port vlan binding mode 5 6 static set port vlan binding mode 5 7 static set port vlan binding mode 5 8 static set port vlan binding mode 5 9 static set port vlan binding mode 5 10 static set port vlan binding mode 5 11 static set port vlan binding mode 5 12 static C460 1 182 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show license User level read only read write admin Use the show license command to display the current licenses installed on the chassis The syntax for this command is show license Example C460 1 gt show license Application License Key State level smon 0000 0000 0000 0000 0000 0000 unlicensed 0 routing 000 000 000 000 000 000 licensed 10 show logout User level read only read write admin Use the show timeout command to display the amount of time the CLI remains idle before timing out in minutes If the result is 0 there is no timeout limit The default is 15 minutes The syntax for this command is show logout Example C460 1 gt show logout CLI timeout is 10 minutes show mac aging User level user privileged supervisor Use the show mac aging command to display the current status of the MAC aging function The syntax for this command is show mac aging Avaya C460 Reference Guide 1
187. rte eee ti 97 Set DoliCy typ6 umet da 97 set port auto negotiation flowcontrol advertisement 99 Set port chanriel cce A e ere e RT SEO 99 set port classification a ai a iA 100 set p rt disable iacet ie eer eere deber pies 101 set port dotlx initialize senys enie nnns 101 set port dol x max feq isn eri eonidas aiye i iaaeaie deaa TS 102 Set port dot1x port control sese eene 102 set port dotlx quiet period sse eene 103 set port dotlx re authenticate ssssssssssseeeee enn 103 set port dotlx re authentication sees eee 103 set port dotlx re authperiod sss 104 set port dotlx server timeout sss enne 104 set port dotlx supp timeout esee eene 105 set port dotbxtx period iuste ete teet 105 set port duplex ee tec eret A A 106 set port edge admin state sss eee nene 106 set port enable e is 107 set port flowcontrol ene iere e eaa a enn nnns 109 set POT level niii ea eene de eie eee te ti er ne E S 110 set port mirror sisse entrent a EE E 110 setportname inei Rib Bee te die e HEP e ie eei aieo rS 111 set port negotiation eocccocccnnoocnnononnnnoncnnoncnnnncnnnnnnnnnnnonnnnnnnnnnnnnnnnn canso nennen 111 set port point to point admin Status sss 112 Set port powerinline vivida 113 set port powerinline priority sss eee 113 set port redundancy didis tertie e ein eie
188. s an RSTP edge port or non edge port 106 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is set port edge admin state lt module port gt lt admin state gt module Number of the module 3 6 port Number of the port on the module If you do not specify a number all the the admin state for all ports on the module is set You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 admin You can set the port admin state to state e edge port non edge port Examples C460 1 set port edge admin state 3 1 edge port port 3 1 edge admin state is set to edge port C460 1 set port edge admin state 3 1 non edge port port 3 1 edge admin state is set to non edge port set port enable User level read write admin Use the set port enable command to enable a port or a range of ports The syntax for this command is set port enable module port module Number of the module 3 6 port Number of the port on the module If you do not specify a number all the ports on the module are enabled You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Avaya C460 Reference Guide 107 Chapter 2 Avaya C460 CLI Commands Example C460 1 set port enable 4 1 Port 4 1 enabled 108 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI
189. s command is show dot1x Example C460 1 gt show dotix mode PAE Capabilities Authenticator Only Protocol Version 1 system auth control disabled Warning Authentication server is disabled not exist and so EEE no authentication can be made show dot1x statistics User level read only read write admin Use the show dotix statistics command to display Rx and Tx EAPOL and EAP statistics The syntax for this command is show dotix statistics 150 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show dotix statistics Rx EAPOL EAPOL EAPOL EAPOL EAP EAP EAP Total Start Logoff Invalid Resp Id Resp LenError 0 0 0 0 0 0 0 Tx EAPOL EAP EAP Total Req Id Req 0 0 0 show dynamic vlans Use the show dynamic vlans command to display automatically learned VLANSs The syntax for this command is show dynamic vlans Router 1 show dynamic vlans VLAN NAME VLAN ID VLAN MAC Default 1 02 e0 3b 1d f9 01 show environment fans User level read only read write admin Usethe show environment fans command to display the current fans status for the switch The syntax for this command is show environment fans Example C460 1 gt show environment fans Mode regular Total working fans 9 Mode Boost Regular Avaya C460 Reference Guide 151 Chapter 2 Avaya C460 CLI Comman
190. s set for all the ports on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 value Number representing the cost The cost level is set from 1 to 65535 A lower cost lower value specifies precedence of a port to forward traffic Example C460 1 gt set port spantree cost 4 2 4096 port 4 2 spantree cost is 4096 set port spantree force protocol migration User level read write admin Use the set port spantree force protocol migration command to set the port as an RSTP port and not as common STA port It forces the port to send a rapid spanning tree BPDU The syntax for this command is set port spantree force protocol migration lt module port gt module Number of the module 3 6 port Number of the port on the module If you do not specify a number the port spantree force protocol migration is set for all the ports on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Avaya C460 Reference Guide 117 Chapter 2 Avaya C460 CLI Commands Example C460 1 set port spantree force protocol migration 1 1 port 1 1 is forced to send a Rapid spanning tree BPDU set port spantree priority User level read write admin Use the set port spantree command to set the Spanning Tree priority level of a port This value defines the priority of a port
191. se the set port static vlan command to assign static VLANs to ports The syntax for this command is set port static vlan module port range vlan num module Number of the module 3 6 port Number of the port on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 vlan range vlan to bind to port Example C460 1 set port static vlan 3 4 6 2 VI VI LAN 2 is bound to port 3 4 LAN 2 is bound to port 3 5 VI LAN 2 is bound to port 3 6 set port trap User level read write admin Use the set port trap command to enable or disable generic SNMP uplink or downlink traps from a port Avaya C460 Reference Guide 119 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set port trap lt module gt lt port gt enable disable module port enable disable Example Number of the module 3 6 Number of the port on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Enable uplink downlink traps Disable uplink downlink traps C460 1 set port trap 3 2 enable Port 3 2 up down trap enabled set port vlan User level read write admin Use the set port vlan command to set the port VLAN ID PVID If adding a new VLAN the VLAN number must be within the range You need to define a vlan before setting a port
192. secondary RADIUS authentication server The syntax for this command is clear radius authentication server primary secondary primary Remove primary RADIUS server secondary Remove secondary RADIUS server Avaya C460 Reference Guide 21 Chapter 2 Avaya C460 CLI Commands Example C460 1 super clear radius authentication server secondary clear rmon2 statistics clear screen User level read write admin Use the clear rmon2 statistics command to delete rmon2 AnyLayer SMON statistics The syntax for this command is clear rmon2 statistics Example Router 14 clear rmon2 statistics Done User level read only read write admin Use the clear screen command to clear the screen The syntax for this command is clear screen clear snmp trap User level read write admin Use the clear snmp trap command to clear an entry from the SNMP trap receiver table The syntax for this command is clear snmp trap rcvr addr all rcvr addr IP address or IP alias of the trap receiver the SNMP management station to clear all Keyword that specifies every entry in the SNMP trap receiver table 22 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example C460 1 clear snmp trap 192 168 173 42 SNMP trap deleted clear system log User level read write admin Use the clear system log command to delete the log file of a Supervis
193. set dot1x re authperiod sss eee eene 85 set dotlx server timeout essere ener enne etras nen en 85 set dott supp im nt Ineas estii e edited 85 set dot1x system auth control disable sss 86 set dot1x system auth control enable sse 86 s t dotIx bcperiod zu sae Er oie ntt eis 87 set icmp redirect enin ri s iine eitan arei eiaeia AE ae nne 87 iv Avaya C460 Reference Guide Contents setiband vlamn soam ae ese dee aa dete so Riu e 88 set intelligent multicast sse eee eene 88 set intelligent multicast client port pruning time s sss 88 set intelligent multicast group filtering delay time 89 set intelligent multicast router port pruning time 0 0 ccc 89 set interface inband sese eee teer eterne tenen tnee testen en 90 set interface outband sees eene ettet eene tenente tes etn nen 90 Setintertace PPP iino stimme eee Act eher a Nr eun 91 set interface ppp enable disable off reset sss 91 setip TOU M 92 set license ase da t mi mel fei n Und 94 Set lOS OE ctn O A E Ble OORT PTET 94 ir AAA eerte reden iie e ie Hte iei e rti iud 95 set mac aging time carriere iirin ia A Eni a EEE R nhe 95 set outband duplex ss mse ioris n a ea irt teen dd 96 Set outband negotiation sss eene nnne 96 set o tbarid speed ee
194. set port powerinline lt module_number port_number gt lt priority gt module Number of the module 3 6 Avaya C460 Reference Guide 113 Chapter 2 Avaya C460 CLI Commands port Number of the port on the module If you do not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 priority The priority level for powering the port e Critical High e Low Example To enable PoE on ports 1 to 3 of module three to High C460 1 set port powerinline 3 1 3 high Load detection process on ports 3 1 3 was set to High set port redundancy User level read write admin Use the set port redundancy command to globally enables or disable the redundancy pairs you have defined Using this command will not delete existing redundancy entries O Disable Spanning Tree before you can enable redundancy The syntax for this command is set port redundancy enable disable Example C460 1f set port redundancy enable All redundancy schemes are now enabled 114 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set port redundancy on off User level read write admin Use the set port redundancy command to defines or remove redundancy pairs The link can be any port that does not belong to a LAG or a LAG interface Ensure that there is no redundancy scheme already defined on any
195. standard protocol for point to point serial connections using a variation of TCP IP SMON Switch Monitoring Avaya s proprietary switch monitoring technology SMON extends the RMON standard to provide additional tools and features for monitoring in the switch environment SMON enables a global view of traffic for all switches on the network an overall view of traffic passing through a specific switch detailed data of the hosts transmitting packets or cells through a switch an analysis of traffic passing through each port connected to a switch and a view of traffic between various hosts connected to a switch SMTP Simple Mail Transfer Protocol Used to send E mail messages between servers Also used to send messages from a mail client to a mail server SNAP SubNetwork Access Protocol Internet protocol that operates between a network entity in the subnetwork and a network entity in the end system SNAP specifies a standard method of encapsulating IP datagrams and ARP messages on IEEE networks SNMP Simple Network Management Protocol Protocol for communications between remote network management stations like a management umbrella console and managed network elements such as Avaya Inc s devices The management umbrella uses SNMP for network management and can manage all SNMP devices Socket An addressable entity within a node connected to an AppleTalk network Sockets are owned by software processes known as socket clie
196. t dscp 156 show ip access list summary 157 show ip route 163 show ip unicast cache host 168 show 12 config 173 show license 183 show log 227 show mac aging 183 show mac aging time 184 show module 185 show module identity 148 show outband 186 show port 187 show port auto negotiation flowcontrol 188 show port channel 188 show port classification 190 show port dotlx 191 show port dot1x statistics 193 show port flowcontrol 194 show port mirror 195 show port point to point status 196 show port trap 197 show port vlan binding mode 198 show powerinline 198 show powerinline budget 199 show ppp authentication 200 show ppp baud rate 200 show ppp configuration 201 show ppp incoming timeout 201 show ppp session 201 show radius authentication 202 show rmon alarm 202 show rmon event 203 show rmon history 204 show rmon statistics 204 show running config 209 show secure access 210 show snmp 211 show snmp retries 212 show snmp timeout 208 212 show spantree 212 show spv 208 214 show startup config 216 show system 217 show system log 208 217 show tftp download software status 219 show tftp upload status 219 show time 220 show time parameters 220 show timeout 183 show trunk 221 show username 222 show vlan 222 show web aux files url 223 sync spv 224 T tech 224 terminal 6 terminal length 225 Avaya C460 Reference Guide 235 Layer 2 CLI Commands terminal width 225 tree 228 U username 229
197. t is 10 The syntax for this command is no ip ospf hello interval seconds seconds integer 52 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example Router 1 configure if marketing ip ospf hello interval 5 Done ip ospf priority User level read write admin O You can only access this command in Interface mode Type interface name at the command prompt to enter Interface mode if necessary Use the ip ospf priority command to configure interface priority used in DR election Use the no ip ospf priority to set the OSPF priority to its default value The default is 1 The syntax for this command is no ip ospf priority priority priority integer Example Router 1 configure if marketing ip ospf priority 17 Done ip ospf router id User level read write admin O You can only access this command in Router OSPF mode Type router ospf at the command prompt to enter Router OSPF mode if necessary Usetheip ospf router id command to configure the router identity Use theno ip ospf router id command to return the router identity to its default lowest IP interface that exists The syntax for this command is no ip ospf router id router id router id IP address Avaya C460 Reference Guide 53 Chapter 2 Avaya C460 CLI Commands ip proxy arp ip redirects Example Router 1 gt ip ospf router id 192 16
198. tem log 217 show tftp upload status 219 show time 220 show time parameters 220 show timezone 221 show vlan 223 show web aux files url 223 sync spv 224 T terminal length 225 terminal width 225 timers basic 225 timers spf 227 Avaya C460 Reference Guide 239 Layer 3 CLI Commands 240 Avaya C460 Reference Guide Glossary 100BASE TX 100 Mbps baseband Fast Ethernet specification based on the IEEE 802 3 standard 100BaseTX uses two pairs of either UTP Unshielded Twisted Pair or STP Single Twisted Pair wiring One pair is used to receive data the other is used to transmit data 10BASE T 10 Mbps baseband Ethernet specification based on the IEEE 802 3 standard 10BaseT uses two pairs of UTP Unshielded Twisted Pair wiring One pair is used to receive data the other is used to transmit data Address Resolution Conversion of an IP address into a corresponding physical address This is usually done using ARP Address Resolution Protocol Agent Network Agent A special control module that interfaces between the network manager and the managed devices using the MIB as a management terms dictionary Network Agents relay device events and execute instructions via embedded software Alarm An audible or visible warning signal alerting designated management stations that a significant event has occurred on the network ARP Address Resolution Protocol A TCP IP protocol used to convert an IP address
199. ter startup Destination file router running Host ob Running state Idle Failure display null Last warning No warning 148 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show cpu load User level read only read write admin Use the show cpu load command to show the current CPU utilization The syntax for this command is show cpu load Example C460 1 gt show cpu load The current CPU utilization is 1 show cs User level read only read write admin Use the show cs command to show the version numbers of the C460 chassis and installed components The syntax for this command is show cs Example C460 1 gt show cs Chassis 1 0 Fans zo Psu 1 v Psu 2 Psu 3 O Slot Type C S 1 M460ML SPV 1 0 2 M460ML SPV 1 0 3 M4612ML G LO 4 M4648ML T 2G PWR 1 0 5 M4648ML T PWR 1 0 6 M4648ML T 2G 1 0 Avaya C460 Reference Guide 149 Chapter 2 Avaya C460 CLI Commands show device mode show dot1x User level read only read write admin Use this command to display the switch operational mode Layer 2 or Layer 3 The syntax for this command is show device mode Example C460 1 gt show device mode Device mode is Router User level user privileged supervisor Use the show dotix command to display the system dot1x capabilities protocol version and timer values The syntax for thi
200. ters and forwards packets between LAN segments Switches operate at the Data Link Layer of the OSI reference model and support any packet protocol Switch Monitoring Refer to SMON on page 253 TCP IP Transmission Control Protocol Internet Protocol Common name for the suite of protocols used to connect hosts on the Internet TCP IP uses several protocols of which TCP and IP are the main ones Telnet A terminal emulation protocol for TCP IP networks Telnet is used for remote terminal connection enabling users to log in to remote systems and use these resources as if they were connected to a local system TFTP Trivial File Transfer Protocol A simple form of File Transfer Protocol using User Datagram Protocol UDP and providing no security features TFTP is often used by servers to boot diskless workstations X terminals and routers 254 Avaya C460 Reference Guide Glossary Transceiver A device that both transmits and receives analog or digital signals Usually used to describe the LAN component that applies signals onto the network wire and detects signals passing through the wire Trap Message sent by an SNMP agent to an NMS console or terminal to indicate the occurrence of a significant event such as a specifically defined condition or a threshold that was reached Similar to an alarm Tree View A resizeable window containing a hierarchical representation of the modules and ports of the device UD
201. the PPP session or to reset the connected modem The syntax for this command is Avaya C460 Reference Guide 91 Chapter 2 Avaya C460 CLI Commands set interface ppp enable enable always disable off reset enable Enable PPP and enter modem mode enable always Enter modem mode every time that the proprietary modem cable is plugged into the console port disable Disable PPP and enter terminal mode off Disconnect the active PPP session reset Reset the connected modem Example C460 14 set interface ppp reset PPP has reset the connected modem Example C460 14 set interface ppp enable Entering the Modem mode within 60 seconds Please check that the proprietary modem cable is plugged into the console port Example C460 1 set interface ppp disable Entering the Terminal mode immediately set ip route User level read write admin Use the set ip route command to adds a route to the IP routing table You can configure from 1 to 10 default static gateways for a C460 switch The syntax for this command is set ip route lt destination gt lt netmask gt lt gateway gt destination IP address of the network or specific host to be added netmask Subnet mask gateway IP address of the router 92 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example This example shows how to add a default route to the IP routing table C460 1 set ip route 0 0 0 0 2
202. the set time protocol command to set the protocol for use in the system as either SNTP protocol or TIME protocol The syntax for this command is set time protocol sntp protocol time protocol sntp protocol Use the SNTP protocol time protocol Use the TIME protocol Example C460 1 gt set time protocol sntp protocol The protocol has been set to SNTP protocol C460 1 gt set time protocol time protocol The protocol has been set to TIME protocol 136 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set time server set timezone User level read write admin Use the set time server command to set the TIME server address The syntax for this command is set time server lt ip address gt ip address IP address of the TIME server Example C460 1 set time server 192 49 53 68 The Server Ip has been set to 192 49 53 68 User level read write admin Use the set timezone command to assign a timezone name and sets the time difference of the device relative to the Coordinated Universal Time UTC GMT The minutes parameter can only be set to 30 The syntax for this command is set timezone lt zone name gt lt hours gt 30 zone name Three character name of time zone for example EST GMT hours The difference between the time zone and GMT Example C460 1 set timezone EST 5 Timezone set to EST offset from UTC is 5 hours Ava
203. to RT PRIMARY MGMT the IP address used in MSNM is selected randomly The syntax for this command is ip routing mode mode mode RT MGMT or RT PRIMARY MGMT mode Example Router 1 config if marketing ip routing mode RT_PRIMARY MGMT 60 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands ip simulate User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the ip simulate command to check the policy for a simulated packet The command contains the addressed list number and the packet parameters The syntax for this command is ip simulate lt access list number gt lt priority gt lt dscp value gt lt source gt lt destination gt lt protocol gt lt source port gt destination port lt established gt access list number integer 100 to 149 priority fwd0 fwdl fwd7 dspc value dscpO dscp1 dscp63 source source ip address destination destination ip address protocol ip tcp udp integer 1 to 255 source port integer 1 to 65535 destination port integer 1 to 65535 established value of TCP established bit Example C460 1 configure ip simulate 100 192 67 85 12 193 76 54 25 ip vlan ip vlan name User level read write admin O You can only access this command in interface mode Typeinte
204. to define a name which includes spaces you must enclose the entire name in quotation marks for example new york ip access list dscp operation User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode if necessary Use the ip access list dscp operation command to set a DSCP to CoS mapping The C460 performs the mapping for only those frames than match an ACL rule with a permit action The syntax for this command is ip access list dscp operation policy list number dscp 40 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands lt action gt policy A valid id number for a policy list currently defined for the module list 100 149 number dscp Range of dscp For example e 0to 63 e lt low dscp gt lt high dscp gt lt low dscp gt lt low dscp gt apply the map to all packets with DSCP from lt low dscp gt to lt high dscp gt action permit do nothing let the packet pass deny drop the packet deny and notify drop the packet and send an SNMP trap e fwd0 fwdlfwd7 Set the frame COS field to 0 7 Example C460 1 configure ip access list dscp operation 101 0 63 permit C460 1 configure ip access list dscp operation 101 62 fwd5 ip access list dscp precedence User level read write admin O If you are at the read write us
205. try The syntax for this command is no network lt ip address gt lt wildcard mask gt ip addr The IP address of the network of directly connected networks wildcard mask Wildcard mask address Exists for compatibility with P550 Example To specify that RIP will be used on all interfaces connected to the network 192 168 37 0 Router 1 configure router rip network 192 168 37 0 Done network OSPF User level read write admin O You can only access this command in Router OSPF mode Type router ospf at the command prompt to enter Router OSPF mode if necessary Use the network command to enable OSPF in this network Use the no network command to disable OSPF in this network The default is disabled Avaya C460 Reference Guide 67 Chapter 2 Avaya C460 CLI Commands The syntax for this command is network lt net addr gt lt wildcard mask gt area lt area id gt net addr IP address wildcard mask Wildcard mask address area id Area ID This parameter exists for compatibility with P550 Example Router 1 configure router ospf network 192 168 0 0 Router 1 configure router ospf area 192 168 0 0 0 0 255 255 area 0 0 0 0 no rmon alarm User level read write admin Use the no rmon history command to delete an existing RMON alarm entry The syntax for this command is no rmon alarm lt Alarm Index gt Alarm Index History index defined using rmon alarmcommand or C460
206. ts to another node on the network The syntax for this command is ping host host Host IP address Internet address of route destination If you do not specify a host IP then the last host IP is used Example to ping the IP number 149 49 48 1 C460 1 gt ping 149 49 48 1 149 49 48 1 is alive ping Layer 3 User level user privileged supervisor Use the ping command to send ICMP echo request packets to another node on the network The syntax for this command is ping host interval size timeout source address gt host Host IP address Internet address of route destination If missing then the last host IP is used interval Interval between ping commands in seconds 1 to 256 size Size of packet in bytes 22 to 66500 timeout Timeout in seconds 1 to 10 source IP address of one of the router interfaces address Avaya C460 Reference Guide 71 Chapter 2 Avaya C460 CLI Commands Example to ping the IP number 149 49 48 1 three times Router 1 ping 149 49 48 1 3 PING 149 49 48 1 56 data bytes 64 bytes from 149 49 48 1 icmp seq 0 time 0 ms 64 bytes from 149 49 48 1 icmp_seq 1 time 0 ms 64 bytes from 149 49 48 1 icmp seq 2 time 0 ms 149 49 48 1 PING Statistics 3 packets transmitted 3 packets received 0 packet loss round trip ms min avg max 0 0 0 redistribute OSPF User level read write admin O You can on
207. twork and subnetwork information from the IP address IPX Internetwork Packet Exchange A network layer protocol used for transferring data from servers to workstations IPX is primarily used in Novell NetWare operating systems ISL Interswitch Link An Avaya proprietary mechanism to tag packets with VLAN and priority information across the backbone This allows two Avaya devices to act as a single logical entity ISO International Standards Organization A voluntary organization founded in 1946 responsible for creating international standards in many areas including computers and communications Jabber An error condition in which a network device continually transmits random meaningless data onto the network In IEEE 802 3 Jabber refers to a data packet the length of which exceeds the maximum length prescribed in the standard Avaya C460 Reference Guide 247 Glossary LAG Link Aggregation Groups LAGs provide a method of creating a high bandwidth link A LAG consists of a group of ports acting as a single logical port All ports participating must have the same configuration LAN Local Area Network A high speed low error data network that spans a limited area LANs connect workstations peripherals terminals and other devices in a single building or other geographically limited area Link State Protocols A series of routing protocols such as OSPF which permit routers to exchange information about the
208. uit or space key to continue set port negotiation 5 1 enable set port level 5 1 0 set trunk 5 1 off set port vlan 1 5 1 set port name 5 1 NO NAME set port trap 5 1 enable set port classuable set port enable 5 1 TERK KKK ck kk ck ck kk ke ke x port 5 2 configuration okckckckck ckckckckck kck kckokok Port type Tranceiver Not Present 4 Link status no link STA status Disabled pk ckckckckckckckck ck ckckck ckckck ck ckckck kckck ck ckckck ck k k k ck ck ck k ck ck kck ck ck k ck ck ck ck ck ck k ck ck ck k ck ck ck kk set port disable 5 2 set port auto negotiation flowcontrol advertisement 5 2 no flowcontrol set port negotiation 5 2 enable set port level 5 2 0 set trunk 5 2 off set port vlan 1 5 2 set port name 5 2 NO NAME set port trap 5 2 enable set port classification 5 2 valuable type q to quit or space key to continue set port enable 5 2 178 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands LER KK ck k ck k ck ck KKK KKK port 5 3 configuration ockckckckckckckckckck kck kc k KE Port type Tranceiver Not Present 4 Link status no link STA status Disabled pAckckck ck ckck k ck ckck k ck ck ck k ck ck ck k ck ck k ck ck ck k AS set port disable 5 3 set port auto negotiation flowcontrol advertisement 5 3 no flowcontrol set port negotiation 5 3 enable set port level 5 3 0 set trunk 5 3 off set port vlan 1 5 3 set port name 5 3 NO NAME set port t
209. ule If you do Optional not specify a number all the ports on the module are shown You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 Auth State The Port Access Entity state Possible states include Initialize Disconnected Connecting e Authenticating e Authenticated e Aborting e Held e ForceAuth e ForceUnauth Avaya C460 Reference Guide 191 Chapter 2 Avaya C460 CLI Commands BEnd Stat The current state od the Backend Authentication state machine Possible states include Request Response e Success Fail e Timeout Idle nit Port Control Port control type Valid values include force authorized e force unauthorized auto Port Status The current value of the controlled port status Possible states include e Authorized Unauthorized Re Auth The state of reauthentication on the port Possible states include Enabled The port connection is reauthenticated after the reAuthPeriod Disabled The port connection is not reauthenticated The reAuthPeriod is ignored Quiet Period The amount of time in seconds between sending authentication requests ReAuth Period The time in seconds after which the port connection should be reauthenticated Server Tmout The amount of time in seconds the P330 waits for a response from the RADIUS server Supp Tmeout The amount of time in seconds before resending auth
210. ure arp 192 168 7 8 00 40 0d 8c 2a 01 Example To remove an entry to the ARP cache for the station 192 168 13 76 C460 1 configure no arp 192 168 13 76 arp timeout User level read write admin O If you are at the read write user level you can only access this command in Configure mode Type configure at the command prompt to enter configure mode Use the arp timeout command to set the amount of time that an entry remains in the ARP cache Use the no arp timeout command to restore the default value 14 400 14 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands The syntax for this command is no arp timeout lt seconds gt seconds The amount of time in seconds that an entry remains in the arp cache Example To set the arp timeout to one hour C460 1 configure arp timeout 3600 To restore the default arp timeout C460 1 configure no arp timeout banner login Use the banner login command to enter the login banner configuration mode Use the no banner login command to set the login banner to the default value Delete the current banner using the no banner login command before creating a new banner The syntax for this command is no banner login Example C460 1 super banner login C460 1 super banner login line See line banner post login Use the banner post login command to enter the post login configuration mode Usethen
211. us of the rmon2 application The syntax for this command is show rmon2 state Example Router 1 gt show rmon2 state RMON2 15 in MATRIX state 208 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show running config User level read only read write admin Use the show running config command to display the current router configuration information The syntax for this command is show running config Example Router 1 gt show running config Router 1 gt Avaya Inc C460ML Multi layer Switch Router configuration version 2 0 2 ip access list name 100 list 100 ip access list owner 100 egotlieb 135 64 102 64 ip access list 100 1 permit ip any any ip access list 100 2 fwd3 udp any eq 68 any eq 67 I set vlan 2 name vlan2 no rmon2 protocol dir TCP 20 no rmon2 protocol dir TCP 23 no rmon2 protocol dir TCP 25 no rmon2 protocol dir TCP 80 no rmon2 protocol dir TCP 110 no rmon2 protocol dir UDP 161 no rmon2 protocol dir UDP 162 rmon2 protocol dir TCP 1111 1111 TCP rmon2 protocol dir TCP 2222 2222 TCP interface 11 ip vlan name Default ip address 11 11 11 1 255 255 2550 I type q to quit or space key to continue interface 12 ip vlan name vlan2 ip address 12 12 12 1 255 3255 255 0 I interface 78 ip vlan name Default ip address 149 49 78 71 255 255 255 0 I ip default gateway 149 49 78 1 1 low
212. ute timer in seconds minimum 30 default 180 O The Invalid Route Timer value must be larger than the Update Timer value It is recommended that it be at least three times greater In any configuration all adjacent routers must have the same values for each of the timer parameters It is possible to have different values for the timers on two adjacent routers provided the Invalid Timer value is at least three times greater on one of the routers than the Update Timer value on the other router Example Router N configure router rip timers basic 30 180 Use the timers basic command to configure the route timer Use the no timers basic command to restore the timers to their default values The syntax for this command is timers basic lt update gt lt invalid gt update RIP update timer in seconds minimum 30 default 30 226 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands timers ospf invalid RIP invalid route timer in seconds minimum 30 default 180 O The Invalid Route Timer value must be larger than the Update Timer value It is recommended that it be at least three times greater In any configuration all adjacent routers must have the same values for each of the timer parameters It is possible to have different values for the timers on two adjacent routers provided the Invalid Timer value is at least three times greater on one of the routers than the Update Timer value on the othe
213. uthentication server Example C460 1 super set radius authentication server 192 40 12 36 primary set radius authentication udp port User level read write admin Sets the RFC 2138 approved UDP port number Normally the UDP port number should be set to its default value of 1812 Some early implementations of the RADIUS server used port number 1645 The syntax for this command is set radius authentication udp port number Example C460 1 super set radius authentication udp port number 1645 set slot power admin User level read write admin Use the set slot power command to power up or power down a slot If there is a module in the slot then the command will reset the device The syntax for this command is set slot power admin lt slot gt lt status gt Slot Slot number Status Up power up the module e Down power down the nodule 126 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example 1 if the slot is empty C460 1 gt set slot power admin 4 up slot 4 power is enabled C460 1 gt set slot power admin 4 down slot 4 power is disabled Example 2 if there is a module in the slot C460 1 gt set slot power admin 4 up This command will RESET the device Reset do you want to continue Y N Y Module in slot 4 is shutting down Attaching network interface 100 done Welcome to C460 SW
214. vaya C460 Reference Guide 133 Chapter 2 Avaya C460 CLI Commands Example C460 1 set spantree tx hold count 3 tx hold count is set to 3 set spantree version User level read write admin Use the set spantree version command to set the rapid spanning tree state machine to work as STP compatible The syntax for this command is set spantree version lt version gt version common spanning tree compatible with ieee802 1D standard rapid spanning tree compatible with ieee802 1W standard Example C460 1 set spantree version rapid spanning tree Spanning tree version is set to rapid spanning tree set system contact User level read only read write admin Use the set system contact command to set the mib2 system contact MIB variable The syntax for this command is set system contact string string The contact name string should be typed inside inverted commas The name is cleared if you leave this field blank Example C460 1 super set system contact gregory kohli Set system contact System contact set 134 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands set system location User level read only read write admin Use the set system location command to set the mib2 system location MIB variable The syntax for this command is set system location string string The location name string should be type
215. version 1 0 1 Login C460 1 gt set slot power admin 4 up This command will RESET the device Reset do you want to continue Y N Y Module in slot 4 is turning on Welcome to C460 SW version 1 0 1 Login set slot power priority User level read write admin Usetheset slot power priority command to configure the power priority for a slot Avaya C460 Reference Guide 127 Chapter 2 Avaya C460 CLI Commands The syntax for this command is set slot power priority lt slot gt lt level gt Slot Slot number e 3to6 e all level critical high e low Example C460 1 set slot power priority 3 high Slot 3 is set to power priority high set snmp community User level read write admin Use the set snmp community command to set or modify the switch s SNMP community strings The syntax for this command is set snmp community lt read only read write trap gt community string Example C460 1f set snmp community read only read SNMP read only community string set set snmp retries User level read write admin Use the set snmp retries command to set the number of retries initiated by the C460 Manager when it tries to send SNMP messages to the switch The syntax for this command is set snmp retries lt number gt number Number of retries 128 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands Example CA46
216. vlan binding mode sse 198 show powerinline eee nre fee erede 198 show powerinline budget ssssssssssssseeneee 199 Show ppp authentication ssssssssseeeeeeee eene nnns 200 Show ppp ba d rate eee e eines 200 viii Avaya C460 Reference Guide Contents show ppp configuration semere ienie eee e een nennen 201 show ppp incoming timeout oo eects este eee eene 201 show Ppp SESSION een pode Ree een ubere tbe tee rad 201 show radius authentication essere nene 202 Show LIMON alarm eee e cete ere PPP IR ERE dee owe e Per RT 202 show rmon event o eecccsssessscssececsecesceceseecsecesscessecessecsececsaeeeaeessecessecensecsees 203 SHOW rmon history escitas cacaos thus 204 SHOW Ion StatiSHcs 5 3 d dest teet diia e og ues 204 show rmon2 dscp stats sss eene nnns 205 show rmon2 protocol dir sse enn 206 show rmon2 protocol dist sse 206 SHOW ti n2 state a ba Len 208 show running config concocccccnnnnncncnoncnnnnonnncnnnonoronononono raro ran nene nnne nennen 209 show secure current oo cecccsscesssecssceesecessecssecesceseeesaeceseecesecesseesseesseeeceecsees 210 show SNMP sei e et a wade cei et pere tipi te aee e pe da 211 shiow snmp retries niece iae lid 212 show snmp timeout nic ti petente i eter ee ees 212 show spantree onosi E e EE EAER E E 212 ShoWSDV cautes tee pte ne a nei eme edna fas 214 show startup conf
217. x of static and dynamic IP addresses Domain A group of computers and devices on a network that are administered as a unit with common rules and procedures Dot1Q Standard for VLAN tagging under the IEEE 802 10 VLAN standard DRU Domain Resource Unit The unit of measure of resources available ina Avaya M770 Device DomainX Duplex Mode The state of the device with regard to simultaneous transmission and reception of information In Full Duplex Mode the device or circuit permits simultaneous transmission and reception This is also known as bisynchronous communication In Half Duplex Mode the device or circuit does not permit simultaneous transmission and reception This is also known as asynchronous communication End System An end user device on a network Also used to denote a non routing host or node in an OSI network ESI End System Identifier A portion of a network address that identifies the end system Ethernet One of the most widely implemented LAN standards Ethernet is standardized as IEEE 802 3 Ethernet uses the CSMA CD access method to handle simultaneous demands and supports data transfer rates of 10 Mbps A newer version of Ethernet called 100Base T or Fast Ethernet supports data transfer rates of 100 Mbps The newest version Gigabit Ethernet supports data rates of 1 Gigabit per second FCS Frame Check Sequence A field added to a frame for error control purposes FDDI Fiber Distributed
218. ya C460 Reference Guide 137 Chapter 2 Avaya C460 CLI Commands set trunk User level read write admin Use the set trunk command to configure the VLAN tagging mode of a port set trunk module port value module Number of the module 3 6 port Number of the port on the module If you do not specify a number the vlan tagging mode is set for all the ports on the module You can also specify a range of ports separated by a dash for example 4 5 13 for ports 5 to 13 on module 4 value off forces the port to become a non tagging port and persuade the neighboring port to become a non tagging port The port becomes a non tagging port even if the neighbor port does not agree to become a non tagging port e dotlq specifies an IEEE 802 10 tagging on a Fast Ethernet or Gigabit Ethernet port Example C460 1 set trunk 3 3 dotiq Dot1Q VLAN tagging set on port 3 3 set vlan User level read write admin Use the set vlan command to configure VLANs The syntax for this command is set vlan lt vlan id gt name lt vlan name gt vlan id vlan number vlan name vlan name Example C460 14 set vlan 3 name gregory VLAN id 3 vlan name gregory created 138 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york set vlan Layer 3 User level read write admin O
219. yntax for this command is show system Example C460 1 show system Uptime d h m s 02 40 55 System Name System Location System Contact eiei sere ionii Snecknicatweiting ere 77 In band MAC address Out band MAC address 02 e0 3b 1d f9 00 02 e0 3b 1d fa 00 show system log User level read only read write admin Displays the encrypted event log file The syntax for this command is show system log The syntax for this command is show system log slot slot Slot number 1 to 2 Avaya C460 Reference Guide 217 Chapter 2 Avaya C460 CLI Commands Example C460 1 gt show system log C460 1 super sh system log type q to quit or space key to continue UpTime 0 37 19 MODUL T kkk E System log file H n AgDwZZioHgDZZZZ ioHgD3D3wD bZZ onD ZZ20AgDN N ZZAojgD 32 gKgjiDZ htllol glgi H n AgDwZZi0HgDZZZZ 10Hg9gD3D3wDeQzZ onD3Z2Z20AgD1xi hn95 s ZZAojgDb 3Z gKgjiDZoNs E ZH YL 2 s H n AgDwZZioHgDZZZZ ioHgDODOTDO0 ZZ onD3Z2Z20AgDt 9 EHN 1ZZAo0jgD030Q3Z gKgjiDZ1WL Z ZM YL Z lt Z s Z H n AgDwZZioHgDZZ2Z 10HgD3D33D332Z onDwZZ20AgDN N ZZAojgD 3Z gKgjiDZ xg glgi H n AgDwZZi0HgDZZZZ 10HgD3DwwD_TZZ onD00 ZZ20AgDSPSAZR 5Z ZAojgDO wTZ gKgjiDZnY z5YZRLEZj Z2 YOZnnKo n90ojig i i9Nt 1n 3PBPl1Zng Ko g9g 9tnn gl1 3PQ 333330 H n AgDwZZ
220. york show ip ospf neighbor User level read only read write admin Displays OSPF neighbor information on a per interface basis The syntax for this command is show ip ospf neighbor lt interface name gt lt neighbor id gt interface name The OSPF interface name neighbor id Neighbor ID Example Router 1 gt show ip ospf neighbor If you wish to define a name which includes spaces you must enclose the entire name in quotation marks for example new york show ip protocols The syntax for this command is show ip protocols lt protocol gt protocol RIP OSPF Optional Example Router 1 super show ip protocols Routing Protocol is rip Sending updates every 30 seconds next due in 0 seconds Invalid after 180 seconds flushd after 300 Redistributing rip Default version control rip version 1 Interface Version Key Routing for Networks Routing Information Sources Gateway Last Update 162 Avaya C460 Reference Guide Chapter 2 Avaya C460 CLI Commands show ip reverse arp User level read only read write admin Use the show ip reverse arp command to display the IP address of a host based on a known MAC address The syntax for this command is show ip reverse arp lt mac addr gt lt match len gt mac addr MAC address match len The number of bytes in the address to match Example Router 1 sh ip reverse arp 00 10 a4 98 97 e0 Showing 1 rows
221. ystem s transmission quality and service availability Query The process of extracting information from a database and presenting it for use RADIUS Remote Authentication Dial In User Service RFC 2138 A protocol for carrying authentication authorization and configuration information between a Network Access Server and a shared Authentication Server Redundancy A duplication of devices services or connections so that in the event of a failure the redundant device service or connection can take over for the one that failed Repeater A device that automatically amplifies restores or reshapes signals distorted by transmission loss Avaya C460 Reference Guide 251 Glossary RIP Routing Information Protocol Specifies how routers exchange routing table information RIP is gradually being replaced by a newer protocol called OSPF Open Shortest Path First RMON Remote Monitoring A network management standard that allows network information to be gathered at a single workstation In contrast to the Standard MIB which gathers network data from a single type of Management Information Base MIB RMON defines nine additional MIBs that provide a much richer set of data about network usage For RMON to work network devices such as hubs and switches must be designed to support it For more information refer to Router A software and hardware connection between two or more networks usually of similar design that

Avaya C460 Switch User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents