APC C5BLK Surge Protector User Manual
Contents
1. Antenna Discharge Unit gt Grounding Conductors Ground Clamps Electric Service Equipment Power Service Grounding Electrode System ii Protect Your Investment Congratulations and thank you for selecting and investing in APC s Model C5 Power Filter At APC we know you have made an intelligent choice sure to reward you for many years To ensure you receive all the benefits and protec tion that accompany your purchase please take a few minutes to fill out and mail the enclosed Warranty Registration Card or complete the online form at www apc com Note Under California law failure to register your purchase may not exclude you from provisions of the Warranty and Equipment Protection Policy Benefits of warranty registration are outlined below Registration Verification Confirmation By registering your By registering your By registering your purchase now it purchase now it confirms purchase now you have guarantees you will your right to maximum a way to confirm yourself receive allthe protection under the as the owner of the information and special terms and conditions of product in the event of offers you qualify for as the Warranty and fire theft or loss the owner of this product Equipment Protection Policy Safety Symbols y This bolt of lightning Y This exclamation point calls indicates uninsulated material attention to features2. Arc APC AV ENGINEERED POWER SOLUTIONS www apc com C Type Power Filter Owner s Manual Models C5 and C5BLK 10 LE 12 13 Safety Information Read this manual Read all of the safety and operating instructions before installing and operating this device Keep this manual Retain this manual and all ofthe safety information that came with this device Warnings Comply with all warnings presented in this manual as well as any found on the device Follow Instructions Follow all operating and use instruction Cleaning Unplug this device from the wall outlet before cleaning Do not use liquid or aerosol cleaners Use a soft damp cloth for cleaning Note A product that is meant for uninterrupted service and for some specific reason such as the possibility of the loss of an authorization code for a cable TV converter is not intended to be unplugged by the user for cleaning or any other purpose may exclude the reference to unplugging this device Water and Moisture Do not use this product near any source of water or in an environment where the relative humidity may exceed 95 non condensing Placement Do not install this device on any unsteady surface Do not install this device on any heat source Power Ensure this device is connected to a properly grounded AC power source Further ensure the device is plugged into a source providing the required 120 Vac Do not use a plug adapte
3. The surge protection feature prevents surges traveling over Coaxial cable from damaging the equip ment Connect the coaxial cable from the DSS or Antenna system to the connector marked IN Connect another coaxial cable from the connector marked OUT to the device being protected DSS or Antenna 9 Installation The installation of the C5 consists of the following steps 1 Make connections 2 Apply power Make Connections Prior to connecting equipment to the C5 Power Filter ensure the unit is functional by connecting the AC Power Cord provided on the side panel Figure 4 Once power is applied to the unit and the unit is powered on the front panel LEDs will illuminate Turn the power switch off all LEDs extinguish Note Due to the unique filtering and surge protection provided by the C5 APC recommends connecting AV components as noted on the outlet panel of the unit Figure 3 Apply Power Apply power to the C5 by pressing the front panel Power Switch Figure 2 inward then releasing the switch Once power is applied to the unit the front panel LEDs are illuminated Dimming of the C5 Display If the LEDs are too bright they can be extinguished without impacting the functionality of the unit To extinguish the LEDs on the top panel push and hold the power button for six seconds The power button should begin to flash Once the button is released all LEDs except the Power Button should be
4. extinguished Please note If you choose to extinguish the LEDs you will not be able to read important information on the panel including input voltage load wiring ok etc 10 Technical Specifications The following table contains the specifications for the C5 and CSBLK Item Specification INPUT Input Voltage Range for Opera 92V 140V tion on utility Nominal Voltage 120 Vac Allowable Input Frequency for 40 70 Hz Operation on utility Rated Input Current 15 Amps Input Circuit Breaker Rating 15 Amps OUTPUT Number of Outlets 10 all outlets are surge protected and conditioned Outlet type NEMA 5 15R Rated Output Current 15 Amps SURGE PROTECTION Let Through Voltage Rating lt 40 Volts Peak Surge Current NM CM 230KA Data Line Protection Jacks split ter Single line 2 wire phoneline pro tection for phone modem or fax Coax 2 Pairs MISCELLANEOUS EMI RFI 40 100 dB 100KHz 30MHz Total Surge Joules 3500 Physical Dimensions H x W x D 19 7 x 5 2 x 2 1 Weight Unpackaged Shipping 5 1 Ibs 6 2 lbs Safety Agency Approvals UL1449 UL 1363 UL CSA FCC Part 15 and Part 68 Class B ll Federal Communications Commission FCC Compliance Information This device complies with Part 68 and Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device must not cause harm
5. 5 Side Panel Connectors Surge Protected COAX RF Connectors The C5 provides surge protection for your CATV system Cable Modem DSS or Antenna system The surge protection feature prevents surges traveling over Coaxial data lines from damaging the system Connect the coaxial cable from the CATV or Cable Modem provider to the connector marked IN Connect other cable from the connector marked OUT to the device being protected CATV box or Cable Modem Circuit Breaker The C5 also provides a press to reset circuit breaker When this breaker is tripped due to an electrical surge or overload the device pops out and shuts down output power to the out lets To reset the circuit breaker push it straight inward CAUTION When resetting the Circuit Breaker push the button in quickly and release the button Do not hold the but ton inward Failure to comply may result in equipment dam age Surge Protected Telephone Jacks The C5 provides a telephone line splitter with surge protec tion to protect components connected via telephone line Connect the supplied RJ11 Telephone cable from the wall jack source to the telephone line connector marked IN Connect other telephone cables to the connector marked OUT and then to the equipment to be protected Telephone DVR DSS or DSL Additional Surge Protected COAX RF Connectors The C5 also provides a surge protection for your DSS system or RF Antenna system
6. depend on APC every day to protect and support many of the most critical networks in the world including those at Microsoft Toyota Motor Sales Inc Time Warner and IBM Over the last 20 years APC has been a pioneer in the development of new power protection technologies that have resulted in countless industry awards design patents and an installed base numbering in the tens of millions of units Multiple R amp D centers along with APC owned and controlled factories ensure APC solutions are the safest most advanced and reliable products available When you buy APC you buy peace of mind Safety Precautions Please ensure you have read and understand all of the safety information located at the front of this manual If you have any questions about the safety information or are concerned that your home may not be properly wired for this equipment please contact APC Technical Support or a qualified and licensed electrician Package Contents Note the C5 and C5BLK have the same performance features and functionality The only difference is color In this manual C5 will be used to refer both to the silver an black models Your C5 package should include the following items e 1 Power Filter e 1 Telphone Cable e 1 Coaxial Cable e 1 User manual e 1 Equipment Protection Policy Sheet e 1 Warranty Registration Card Unit Power Capacity The C5 is rated for 15 Amps The C5 is capable of supplying the dynamic peak current draws requ
7. e arranged according to the type of filtering protection provided for a given applica tion These Isolated Noise Filter Banks eliminate electromag netic and radio frequency interference EMI RFI that can negatively impact sound and video quality APC recommends you plug your devices into the outlets as marked in order to assure optimum protection for your equipment The outlets are further defined in the following Digital Filter Outlets provides filtering of the incoming AC power to protect your most sensitive digital devices CD DVD DVR CATV SAT Monitor and AUX one auxiliary digital device Note Any digital device can be plugged into the digital out lets any video device can be plugged into either of the video outlets etc Example if you have a cable box and a satellite receiver but no monitor you can plug the cable box into the CATV SAT outlet and the satellite receiver into the MON ITOR outlet Video Filter Outlets provides filtering for your video devices TV and VCR Analog Filter Outlets provides filtering for your analog based equipment Tuner AUX and Preamp Receiver High Current Filter Outlets provides filtering for your high current devices Subwoofer and Amplifier Side Panel Controls and Indicators The side panel connectors for the C5 Power Filter are detailed in Figure 4 Each numbered callout refers to the numbered description found in the following pages CIRCUIT BREAKER Figure 4 C
8. ements vi Introduction 1 Proven Expertise Proven Reliability 1 Safety Precautions 2 Package Contents 2 Unit Power Capacity 2 Features 3 Surge Protection 3 Isolated Noise Filter Banks INFB 3 10 Outlets 3 Top Panel 4 Top Panel Controls and Indicators 4 Outlet Panel and Side Panel 6 Outlet Panel 6 Side Panel Controls and Indicators 8 Installation 10 Make Connections 10 Apply Power 10 Dimming of the C5 Display 10 Technical Specifications 11 Troubleshooting 13 vi Introduction Congratulations on your purchase of APC s C5 Power Filter Figure 1 This unit will protect your high performance audio and video AV system from damaging power surges spikes and lightning Protection is guaranteed Isolated noise filter banks will eliminate EMVRFI as a source of audio and video signal degradation Data line surge protection jacks will stop surges traveling over phone and ethernet lines Digital Satellite System Cable Modem and CATV Coaxial Cable lines are equally protected With APC your entire home entertainment experience is protected from damage as a result of bad power ADS s e d A dd ee C5 POWER FILTER Figure 1 C5 Power Filter Front View Proven Expertise Proven Reliability From corporate data centers to home offices APC is regarded as an innovator designer and manufacturer of high quality power protection solutions With a proven reputation for Legendary Reliability leading companies
9. ered callout refers to the numbered description found immediately below the picture C5 POWER FILTER Figure 2 C5 Front Panel Controls and Indicators Wiring OK Status Indicator When lit the receptacle the C5 is plugged into is properly wired If not lit one of three wiring problems exists in the building wiring circuit missing ground overloaded neutral or reversed polarity An electrician should be consulted to resolve the problem Protection On Status Indicator When lit the C5 is functioning properly If the light is extinguished the C5 has been hit by a surge and the protection circuitry may be damaged Filtering Status Indicator When lit notifies the user that the EMI RFI noise reduction circuit is active Overload Status Indicator If illuminated this LED indicates the C5 is overloaded Unplug components until the light is extinguished On Off switch Controls power to all 10 outlets APC recommends the C5 be left on at all times When illiminated power is on at all outlets Outlet Panel and Side Panel The following section describes the functionality of the outlet and side panels Outlet Panel The outlet panel for the C5 Power Filter is deteailed in Figure 3 Each numbered callout refers to the numbered description found in the fol lowing pages Figure 3 C5 Outlet Panel AC Powered Outlets The C5 Power Filter provides for connection of up to ten 10 AC powered devices The outlets ar
10. for which within your unit that may you should read about in this cause an electrical shock For Manual to prevent operating the safety of everyone in your and maintenance problems home please do not remove the product cover Warnings Cautions and Notes Warnings Cautions Notes Warnings provide Cautions provide Notes provide information about a information about a information that is procedure that if not procedure that if essential to performed exactly as not performed highlight stated may result in exactly as stated injury or death may result in equipment damage 111 Class B Labeling and Instruction Manual Requirements Devices subject to Certification must be labeled with an FCC Identifier Devices subject to Verification or Certification must be labeled with the following compliance statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation In addition for a Class B digital device or peripheral the instructions furnished the user shall include the following or similar statement placed in a prominent location in the text of the manual Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate
11. ful interference and 2 This device must accept any interference received including interference that may cause undesired operation As required the bottom of this equipment contains among other information the Registration Number and Ringer Equivalence Number REN for this equipment If requested this information must be provided to the telephone company 12 Troubleshooting This section describes possible causes and solutions for the following problems e Unit will not turn on e Wiring OK Indicator LED is not illuminated Unit will not turn on Probable Cause Input power cord is not connected properly Solution Ensure supplied power cord is connected firmly to the wall outlet Probable Cause No power or insufficient power available at the wall outlet Solution Ensure the wall outlet has good power by using a voltmeter or by plugging in another device Note The unit will not turn on and accept incoming utility power if the power is out of range Probable Cause Circuit Breaker has tripped Solution Check both home and unit circuit breakers If the circuit breaker located on the side of the C5 has tripped the center post will be extended outwards about a quarter to half inch Push it back in to reset it If the trip occurs again reduce the amount of equipment plugged into the unit and try again While the unit s breaker is rated for 15 Amps National Electric Code NEC dictates that any particular ho
12. ired by any component designed to work on a 15A circuit Despite their nameplate power ratings high performance AV equipment draw much less than their listed power ratings The C5 can inform the user how much of the power capacity is available as equipment is connected to the unit Features The following are major features of the Model CS Surge Protection The C5 Power Filter provides a high level of surge protection for the voltage going into the unit thus protecting the devices connected to the unit Additionally surge protected coax radio frequency RF connectors are protected against surges traveling over coaxial lines to protect your digital satellite system DSS CATV box or cable modem Similarly the telephone line surge protection feature provides protection for telephone modem Digital Subscriber Line DSL modem fax digital video recorder DVR DSS system set top internet service provider such as WebTV or pay per view cable TV function Isolated Noise Filter Banks INFB The C5 also provides INFB technology to eliminate electromagnetic and radio frequency interference that can negatively impact sound and video quality 10 Outlets All outlets provide surge protection and noise filtering Top Panel The following section describes the controls and indicators on the top panel Top Panel Controls and Indicators The top panel controls and indicators for the C5 Power Filter are detailed in Figure 2 Each numb
13. me circuit should not be loaded more than 80 of its rating If the this problem remains unsolved contact APC Technical Support at 888 88APCAV or by visiting www apcav com Probable Cause Unit is overloaded Solution The load bar top panel of the C5 If the display indicates over 100 LED lights in red or close 100 LED lights in yellow the unit may be overloaded If the unit is overloaded or nearly overloaded gt 95 it is recommended that the load be reduced by unplugging one or more components 13 Wiring OK Indicator LED is not illuminated Probable Cause There are 3 reasons why this LED would not be illuminated 1 Reversed polarity exists at the wall outlet 2 Neutral wire is overloaded 3 Earth ground is missing at the wall outlet Solution Operating the unit under such conditions may impact its surge protection performance Contact an electrician to have them inspect the building or home wiring to fix the problem Probable Cause Unit is on but LEDs are turned off Solution Push the Power button push the Select button twice turns the unit off and back on again The LEDs should illuminate 14 15 990 2377 Copyright 2005 American Power Conversion All rights reserved The APC AV logo is a registered trademark of American Power Conversion All other trademarks are the property of their respective owners 16
14. r which defeats the ground pin of the AC plug Polarization This device has a polarized AC line plug having one blade wider than the other This plug will only fit into the wall outlet in one orientation This is a safety feature Do not remove the round grounding pin or use an adapter that defeats this safety feature Power Cord Ensure power cords are routed in a manner that will preclude them being pinched frayed or stepped on After connecting other devices to this device do not push the rear of the device up against any surface wall or shelving unit as this may create an undesired bend in the power cords which may break the wire strands of the cord Antenna Grounding Although this device provides protection against electrical surges when connecting an outside antenna or cable system to devices connected to this device ensure the antenna or cable system is grounded so as to provide additional protection against voltage surges and static charges in accordance with Section 810 of the National Electric Code ANSI NFPA No 70 see illustration next page Lightning This device employs Metal Oxide Varisters MOVs and other circuitry to protect against lightning and other sources of voltage surges and sags It is not necessary to turn this device or the devices connected to this device off during a lighting storm Power Lines Do not locate outside antenna systems near overhead power lines or other electric light or power circuit
15. s or where it may fall or otherwise come in contact with these power sources Do not allow the ladder being used or the antenna itself to come into contact with these power sources and such contact may be fatal 14 15 16 17 18 Safety Information continued Overloading Do not overload the wall outlet where this device is being connected Do not overload this device Ensure the total load to this device does not exceed that which is listed in the Specifications section of this manual Servicing There are no user serviceable components within this device Removal of any cover from this device may present a shock hazard and or void the warranty Damage Requiring Service If any type of damage occurs to this device immediately disconnect it from the wall outlet Do not use the Power switch or line cord into the rear of the device to disconnect power Notify APC Technical Support or Customer Service at once Replacement Parts There are no components within this device that can or should be removed replaced unless it is by an APC qualified technician Periodic Inspection Inspect the line cords telephone data cords or DSS Cable TV coaxial cables connected to this device to ensure they remain fully pushed in or attached and that they are not frayed or otherwise damaged EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRIC CODE NEC Sg Ground Clamp Antenna Lead In Wire
16. the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the CC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiated radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures _ Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced audio TV technician for help If shielded cables or other specialized accessories are necessary for the unit to achieve compliance a statement similar to the following should be added Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits Table of Contents Safety Information i Protect Your Investment iii Class B Labeling and Instruction Manual Requir
Download Pdf Manuals
Related Search