AMX DAS-KP-LCDS-W Speaker System User Manual
Contents
1. AMX is not liable for any damages caused by its products or for the failure of its products to perform This includes any lost profits lost savings incidental damages or consequential damages AMX is not liable for any claim made by a third party or by an AMX Autho rized Partner for a third party This Limited Warranty does not apply to a any AMX product that has been modified altered or repaired by an unauthorized agent or improperly transported stored installed used or maintained b damage caused by acts of nature including flood erosion or earth quake c damage caused by a sustained low or high voltage situation or by a low or high voltage disturbance including brownouts sags spikes or power outages or d damage caused by war vandalism theft depletion or obsolescence This limitation of liability applies whether damages are sought or a claim is made under this warranty or as a tort claim including negligence and strict product liability a contract claim or any other claim This limitation of liability cannot be waived or amended by any person This limitation of liability will be effective even if AMX or an authorized representative of AMX has been advised of the possibility of any such damages This limitation of liability however will not apply to claims for personal injury Some states do not allow a limitation of how long an implied warranty last Some states do not allow the limitation or exclusion of inci2. an EFA Operation Reference Guide Audio Controller LCD Keypads Flush Mount LCD Keypad DAS KP LCD G Surface Mount LCD Keypad DAS KP LCDS W Distributed Audio Last Revised 3 03 2008 AMX Limited Warranty and Disclaimer This Limited Warranty and Disclaimer extends only to products purchased directly from AMX or an AMX Authorized Partner which include AMX Dealers Distributors VIP s or other AMX authorized entity AMX warrants its products to be free of defects in material and workmanship under normal use for three 3 years from the date of purchase with the following exceptions e Electroluminescent and LCD Control Panels are warranted for three 3 years except for the display and touch overlay compo nents are warranted for a period of one 1 year Disk drive mechanisms pan tilt heads power supplies and MX Series products are warranted for a period of one 1 year e AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products as long as the AMX lighting products are under warranty AMX also guarantees the control of dimmable loads that are properly con nected to our lighting products The dimming performance or quality there of is not guaranteed impart due to the random combi nations of dimmers lamps and ballasts or transformers e AMX software is warranted for a period of ninety 90 days e Batteries and incandescent lamps are not covered under the
3. down A soft click should be heard when the bezel is freed from the mounting plate 2 Use a small Phillips screwdriver to remove the four screws in the corners of the LCD board Once all the screws have been removed gently grip each side of the LCD screen and rock it away from the mounting plate This will slowly release the LCD screen from the bank of pins connecting it to the Keypad Control Board el e Y NOTE Plug the speaker wire connectors to the To Speakers connector and plug the Zone wires into the To Controller connector on the back of the Keypad Connector Board Ensure the wiring scheme is correct and that the connector at the Controller is plugged into the Zone output Use the provided screws to mount the Keypad Mounting Plate to the j box in the wall Make sure the screws are secure enough that the keypad will not move when touched but be sure not to overtighten the screws If the screws are over tightened the connection between the LCD Screen and the Keypad Control board may not be adequate Reconnect the LCD screen to the Keypad Control board making sure to line up the four screw holes correctly This will ensure that all the pins will plugged into their appropriate receptacles Secure the LCD screen with the four screws that were removed in step 2 Make sure the volume buttons are still in place on the switches Before placing the Front Bezel over the screen POWER ON the Controller and Expansio
4. not used station AM CD To enter a specific Disc amp Track touch NUMERIC and enter the Disc touch the dot then enter the Track plus ENTER disc and track must be separated by dot To enter a specific Track while listening to a Disc touch NUMERIC and enter the Track plus ENTER ee Cable Satellite To enter a specific channel touch NUMERIC and enter the Channel plus ENTER Presets Setting amp Recalling Source MORE Screen Set Preset Screen Recall Preset Screen FIG 2 Basic Functionality Setting and Recalling Presets Setting a Preset Presets can only be set from the Source MORE screen Touch PRESETS A numeric screen will be displayed Enter the Station CD amp Track Channel plus ENTER A Presets screen will be displayed with 10 possible preset positions ae Se NS Select any preset position Recalling a Preset From the Source MAIN screen touch PRESETS and select the desired preset Access the Source MORE screen from the source MAIN screen by touching MORE gt gt NOTE NOTE Advanced Functionality Mi Series amp DELTA Advanced functions are accessed by simultaneously pressing amp holding the Vol Vol buttons for 3 seconds FIG 3 shows the Advanced Functionality screen for KP LCD Keypads Room Grouping options Alarm Clock options Keypad Lock options Tone Control settings Backlight settings FIG 3 KP LCD Advanced Functionality screen Advance
5. KP 4e KP 6e and DAS KP NUM keypads with the added benefit of visual feedback The DAS KP LCD G is available in the following colors Gloss Black FG1120 01 Gloss White FG1120 02 Gloss Almond FG1120 03 Gloss Ivory FG1120 04 DAS KP LCDS W Surface Mount LCD Keypad FG1120 1 2 The DAS KP LCDS W Surface Mount retrofit LCD Keypad combines the control functionality of the DAS KP 4e G KP 6e G and DAS KP NUM G keypads with the added benefit of visual feedback The DAS KP LCDS W is available in the following color Matte White Audio Controller Keypads Features By Model The following table indicates the features supported by each of the Matrix Audio Controller Keypads Audio Controller Keypads Features By Model LCD Keypads e DAS KP LCD G FG1120 0X Flush Mount LCD Keypad e Direct access control e Setting recalling presets e Setting recalling favorites e DAS KP LCDS W FG1120 12 Surface Mount LCD Keypad e Zone grouping e Alarm clock settings e Keypad lockout Pushbutton Keypads e DAS KP 4e G FG1120 3X Flush Mount 4 Source Keypad e Control of 4 sources e 5 button navigation control Bass treble and balance control e Built in IR receiver Flush Mount 4 Source Keypad e DAS KPI 4e G FG1121 3X International e Metal chassis for enhanced rigidity e Field replaceable buttons and bezel e Opaque button color e 4 pin input output connectors e 5 button navigation control e Bass treble and b
6. N e ALWAYS OFF e AUTO ON backlight turns off after 30 seconds Privacy Mode To access Privacy mode 1 Select MORE gt gt in the Setup Main screen FIG 9 Main Setup screen Privacy Mode screen FIG 9 Privacy Mode screen 2 Select PRIVACY MODE to display the Privacy Mode More screen FIG 10 Privacy Mode More screen Privacy Mode FIG 10 Privacy Mode More screen Privacy Mode lt lt BACK will return you to the Setup Main screen FIG 3 NOTE 3 Selecting OK on the Privacy Mode More screen will set the room to Privacy Mode no pages will be heard in this room 4 Select CANCEL to return to the Main Screen where you can select a Source Using the LCD Keypads 16 Matrix Audio Controller LCD Keypads Using the LCD Keypads KP LCD Audio Controller Keypads 17 It s Your World Take Control 3000 RESEARCH DRIVE RICHARDSON TX 75082 USA 800 222 0193 e 469 624 8000 469 624 7153 fax 800 932 6993 technical support www amx com 3 08 2008 AMX All rights reserved AMX and the AMX logo are registered trademarks of AMX AMX reserves the right to alter specifications without notice at any time
7. R Command Name will be highlighted Use the UP DOWN buttons to change the letters in the IR command name To move from letter to letter use the FORWARD button To delete a letter use the BACK button Press the CENTER button to save the label C Source Command Names are limited to 6 characters NOTE Using the LCD Keypads Basic Functionality Mi Series amp Delta HOME Screen Source MAIN Screen Source MORE FIG 1 Basic Functionality Home Source MAIN and Source MORE screens Turn On a Source Single Room Touch the desired source The LCD screen will switch to the Source MAIN screen and the source will begin playing An arrow will be displayed beside the source name to indicate that the source is ON see FIG 1 Turn Off a Source Single Room Touch the source that is currently On The source will no longer play and the arrow will no longer be displayed beside the source name Turn a Source On in All Rooms From the HOME screen touch ALL ON The text Select Source will flash Touch the desired source All rooms will begin playing the selected source Turn All Rooms Off System Off From the HOME screen touch ALL OFF Audio in all rooms will be turned off Direct Entry From The Source Main Screen Tuner To enter a specific station touch NUMERIC The numeric screen will be displayed Touch the station numbers plus ENTER Examples 104 5 use the dot for FM stations 1050 if dot is
8. alance control e Built in IR receiver Flush Mount 6 Source Keypad e DAS KPI 6e G FG1121 4X International e Metal chassis for enhanced rigidity e Field replaceable buttons and bezel e Opaque button color e 4 pin input output connectors e DAS KP NUM G FG1120 2X Flush Mount Numeric Keypad e 12 button numeric control e Direct access control e Setting recalling presets Flush Mount Numeric Keypad e Setting recalling favorites International e Zone grouping e Alarm clock settings e DAS KPI NUM G FG1121 2X e Keypad lockout Installing the Surface Mount LCD Keypad DAS KP LCDS W Overview The DAS KP LCDS W Surface Mount LCD Keypad FIG 1 is shipped completely assembled To correctly install the DAS KP LCDS W retrofit in the wall you must remove the Front Bezel and the LCD screen Please follow these instructions carefully to ensure correct installation and operation FIG 1 DAS KP LCDS W Surface Mount Retrofit LCD Keypad Parts List e Front Bezel e Keypad Control Board e Mounting Plate e LCD Touch screen e Keypad Connector Board e Mounting Screws x 2 Before installing the LCD Keypads POWER OFF the Matrix Controller and Expansion Controllers if applicable CAUTION 1 To remove the Front Bezel firmly hold the rear connector board with one hand while squeezing the top and bottom near one edge of the front bezel with the other hand While squeezing gently pull the bezel back and
9. and housing into the hole in the wall 4 Press the housing firmly against the wall and tighten the 4 mounting screws black Phillips head located in each corner of the housing This will cause the doglegs to extend and press against the drywall and will secure the Keypad to the drywall Be sure not to over tighten these screws 5 Remove the protective film from the front of the LCD Touch screen ee a NOTE 6 Carefully place the keypad bezel on the front of the Keypad Start on one side making sure the volume button fits through the appropriate volume hole and gently squeeze the cover to secure it to the other side of the housing The second volume button may need to be pressed in order to fit through the appropriate volume hole 7 POWER ON the controller and Expansion Controllers if applicable The DAS KP LCD G will start the initialization process immediately When the System is first powered ON it could take up to 4 minutes to load all the information to the LCD keypads Please wait until initialization has completed before using the keypad 8 If everything initialized correctly you should see the source listing at the top of the screen and All On All Off and the time displayed at the bottom of the screen 9 To remove the cover gently pry from the top corner until all four clips release from the housing Customizing LCD Keypad Labels Overview Customization of labels displayed on the LCD keypad is d
10. d Functionilty is largely reserved for Mi Tango Controllers Only Backlight and Tone except for SRS are available on Delta Controllers Grouping Rooms Group Screen Create Group Screen FIG 4 Advanced Functionality Creating Groups 1 With the desired source ON access the Advanced screen and select GROUP ROOMS Select Create a Group to specify the rooms to be included in the Group Select Group ALL to group all rooms When a group is created all rooms included in the group will behave as one room same source amp volume To adjust the Group Volume Touch Vol Vol while on the Group screen To adjust the Volume for an individual room exit the Group screen and touch Vol Vol from the keypad in each room To clear a Group access the Group Room screen and touch Clear Group Setting Clearing the Alarm Clock FIG 5 Alarm Clock options To set an Alarm for a specific room access the Advanced screen and select ALARM CLOCK Select Set Alarm Select the source by touching Source to scroll through the available sources Pe NS Set the time amp adjust the volume and touch SET When the selected time is reached the room will turn on to the selected source and the volume will ramp up to the set volume To clear an Alarm for a specific room select Clear Alarm from the Alarm Clock screen To clear all Alarms for all rooms select Clear All Alarms from the Alarm Clock screen L
11. dental or consequential damages for consumer products In such states the limitation or exclusion of the Limited Warranty may not apply This Limited Warranty gives the owner specific legal rights The owner may also have other rights that vary from state to state The owner is advised to consult applicable state laws for full determination of rights EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY AMX MAKES NO OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AMX EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY EXCEPT AS OTHERWISE LIMITED BY APPLICABLE LAW AMX RESERVES THE RIGHT TO MODIFY OR DISCONTINUE DESIGNS SPECIFICATIONS WARRAN TIES PRICES AND POLICIES WITHOUT NOTICE Table of Contents Matrix Audio Controller LCD Keypads ccssccsscssccsscnsccsscnsccsscessosscessosees 1 QV EI VIC WY oore E A EEE AEE E E E E sane seeeecases 1 DAS KP LCD G Flush Mount LCD Keypad FG1120 0X sseesesseossossossossossosssessessseoe 1 DAS KP LCDS W Surface Mount LCD Keypad FG1120 12 nseeseessesseosscsssessesssosees 1 Audio Controller Keypads Features By Model csssccssccssccesccnsccesccesccssccsseesseness 2 Installing the Surface Mount LCD Keypad DAS KP LCDS W sesceeseees 3 ONEVIEW co cre
12. e areca ner N E E A E E E E A E 3 Installing the Flush Mount LCD Keypad a ae a E e E E E E S E E E A O E E D OVE VIC WY Aoao ea PEE E E S EE A EE E E 5 Customizing LCD Keypad Labels eseoseseesessesecscsecsssseseeseoecseceesecsesecseoseseoseoee 7 MI VOT VIC W sestari S E E 7 CUSTOMIZING SOURCE Labels arias sacausccusciccasancmnsissussvaccavesodeaveswnstisacenersuennsacesgesemadedesunesuanaes 7 Customizing Source Command Labels csssccssccssccesccesccnsccesccssccssccssecsscesseoeseees 8 Using tne LCD cfr eee rere errr rer nnrr en rey eii nn Serr men nner rem mane re ner errr te rr 9 Basic Functionality Mi Series amp Delta cccccssccesccsccssccsccsscesccsscesccsscescceseescees 9 T rn On a Source Single ROOM tose csvacoescesesscnupsoueucssternanenseac ecaanneensanadareccslspaaecaaneceseesdeaawes 9 Tarn Off a Source Single ROOM wssssesssccsedeusedvodcanaontenssnseusteinacnsbovsewoaaacepasesoeeastssonsoebeedeet 9 Turn a Source On in All ROOMS suis sesdesacnscasacencarevansscvanduedoasnsdenadeaccenduesnasdeannesascescoaanwanaaeas 9 Turn All Rooms Off System Off ccscsstsacesctassa vacewensaseceesacesaccacscascsacenieanexenassieviessssouscesecee 9 Direct Entry From The Source Main Screen cssccsccssccsscesccsccesccsscesccsscsseescens 9 TOON E E E A E A E E E E E E E E T P T E cous 9 CD a E E E E E E E eas 9 Cable Sac SUNG Eca E EE E E A E E EES 10 Presets Setting amp Recalling
13. n Controllers if applicable The DAS KP LCDS W will start the initialization process immediately When the System is first powered ON it could take up to 4 minutes to load all the information to the LCD keypads Please wait until initialization has completed before using the keypad 8 If everything initialized correctly you should see the source listing at the top of the screen and All On All Off and the time displayed at the bottom of the screen Remove the protective film from the front of the LCD Touch screen Place the Front Bezel on the LCD screen and firmly click it into place It should fit tightly to the Mounting plate Installing the Flush Mount LCD Keypad DAS KP LCD G Overview The DAS KP LCD G Flush Mount LCD Keypad FIG 1 is shipped completely assembled FIG 1 DAS KP LCD G Flush Mount LCD Keypad Flushmount Parts List e Front Bezel e LCD Touch screen amp Housing Before installing the LCD Keypads POWER OFF the Matrix Controller and Expansion Controllers if applicable CAUTION 1 Using the cut out template provided center the template on the desired location on the wall and mark the hole to be cut 2 Connect the appropriate speaker amp controller cables to the back of the DAS KP LCD G The speaker connector is located on the right hand side The controller connector is located on the left hand side 3 Remove the bezel from the front and insert the LCD Keypad
14. ocking Unlocking Keypads FIG 6 Keypad Lock Options When a keypad is locked touching the screen or buttons will have no effect until the keypad is unlocked 1 To lock a keypad select LOCK KEYPADS from the Advanced screen and select LOCK UNLOCK 2 Select the room to be locked unlocked and touch SAVE or MORE To unlock all keypads select UNLOCK ALL from the Lock Keypads screen Tone Control Settings Bass Treble Balance SRS Tone Control Screen FIG 7 Tone Control Settings SRS WOW is a registered trademark of SRS labs Inc Bass Treble Speaker Balance amp SRS can be adjusted for each room by accessing the Advanced screen and selecting TONE CONTROL SRS is supported only on Mi Series Audio Controllers NOTE To adjust Bass touch BASS or To adjust Treble touch TREBLE or To adjust Speaker Balance touch BAL lt L gt or lt R gt To add change an SRS option touch SRS and select one of the following options e BASS BOOST e 3D e WOW e FOCUS To remove or turn SRS off select SRS OFF from the SRS screen Backlight Settings FIG 8 Backlight Settings The Intensity and Mode can be adjusted for the LCD keypad by accessing the Advanced screen and selecting BACKLIGHT To adjust Intensity touch the to increase decrease the brightness of the screen range 5 95 To adjust the Mode touch the text to scroll through the following options e ALWAYS O
15. one via the Setup menu on the front of the Controller Both Source labels and Source Control labels can be customized FIG 1 A Source Labels Source Control Labels FIG 1 Source Labels and Source Control labels Customizing SOURCE Labels 1 Enter the Setup menu from the front of the Matrix Controller by pressing the SELECT button FIG 2 T S W FIG 2 Press the SELECT button on the front of the Matrix Controller 2 From the menu displayed select SETUP MRC PROGRAM 3 Select the source of which you wish to customize the source name The default Source name will be displayed 4 Select Label The first letter of the Source Name will be highlighted Use the UP DOWN buttons to change the letters in the source name To move from letter to letter use the FORWARD gt gt button v e a a To delete a letter use the lt lt BACK button Press the CENTER button to save the label C Source Names are limited to 6 characters NOTE Customizing Source Command Labels Enter the Setup menu from the front of the Matrix Controller by pressing the SELECT button From the menu displayed select SETUP MRC PROGRAM Select the source of which you wish to customize the source command name Select Learn IR The first IR command for the source will be displayed Select Next until the IR command you wish to customize is displayed yo ef o YS Select Label The first letter of the J
16. oseeseossossoseossossossossossossossossescssesssosessessessessessessesse 10 SONG aA Prose Desersioreo sraa Nna OA E ARARE 10 Recalling a Prece tentenin a E A E E ET 10 Advanced Functionality Mi Series amp DELTA ccsscssccsscesccsccesccsscesccssceseeess 11 Grouping ROOMS sissien a a oa aa 11 Setting Clearing the Alarm Clock eoeeeseoeeoseosesscsscsecsscsecsecsecssesecseossoseossossossossossoseoe 12 Locking Unlocking Keypads eseeseeseeseeseesesseeseessoseoseoseeseesseseosecssessossoseoseosessessesssoseose 12 Tone Control Settings Bass Treble Balance SRS scesssccssssceessccesssceeessceesseeeeees 13 Backlight Settings escceencscsesecescsscenvsecnce cocunessnecacecsene ar A EREEREER 14 Privacy Modesa E E E 14 Table of Contents ji Matrix Audio Controller LCD Keypads Matrix Audio Controller LCD Keypads Overview The Matrix Audio Controller LCD Keypads FIG 1 are compatible with both Delta and Mi Series Audio Controller Systems and provide Direct Access Control and advanced functionality such as Setting and recalling Source Presets Setting and recalling Source Favorites Zone Grouping Alarm clock settings Keypad Lockout DAS KP LCD G DAS KP LCDS W Flush Mount LCD Keypad Surface Mount LCD Keypad FIG 1 Matrix Audio Controller LCD Keypads DAS KP LCD G Flush Mount LCD Keypad FG1120 0X The DAS KP LCD G Flush Mount LCD Keypad combines the control functionality of the DAS
17. warranty AMX AutoPatch Epica Modula Modula Series4 Modula CatPro Series and 8Y 3000 product models will be free of defects in materials and manufacture at the time of sale and will remain in good working order for a period of three 3 years following the date of the original sales invoice from AMX The three year warranty period will be extended to the life of the product Limited Lifetime Warranty if the warranty card is filled out by the dealer and or end user and returned to AMX so that AMX receives it within thirty 30 days of the installation of equipment but no later than six 6 months from original AMX sales invoice date The life of the product extends until five 5 years after AMX ceases manufacturing the product model The Limited Lifetime Warranty applies to products in their original installation only If a product is moved to a different installation the Limited Lifetime Warranty will no longer apply and the product warranty will instead be the three 3 year Limited Warranty All products returned to AMX require a Return Material Authorization RMA number The RMA number is obtained from the AMX RMA Department The RMA number must be clearly marked on the outside of each box The RMA is valid for a 30 day period After the 30 day period the RMA will be cancelled Any shipments received not consistent with the RMA or after the RMA is cancelled will be refused AMX is not responsible for products returned without a valid RMA number
Download Pdf Manuals
Related Search