Home
American DJ XDM-352 DJ Equipment User Manual
Contents
1. PHROformer Series Americaa OF o AUDIO User Instructions XDM 352 PREAMP MIXER Thank you for purchasing this American DJ product The XDM 352 Is ready to be used there is no assembly required Please read the following instructions before installing or using your new unit The XDM 352 has a 2 year limited warranty CAUTION Keep this device away from rain and moisture Safety Instructions Always plug in the power last Make sure that the Power switch is set to the OFF position before connecting other devices to the mixer Keep away from heaters and other heating sources If the device has been exposed to drastic temperature fluctuation e g after transportation do not switch on the mixer immediately The arising condensation of water might damage your device Leave the device switched off until it has reached room temperature Never put any liquids on the mixer or close to it Should any liquid enter the device disconnect from main power immediately Have the device checked by a qualified service technician before operating again Any damage caused by liquid entering the device is not subject to warranty Never let the AC cord come in contact with other cables Handle the AC cord and all AC connections with particular care Make sure that the available voltage is not higher than stated on the AC voltage selector 25 Before the device is switched on all fader and volume controls should be set to 0 or minimum posi
2. The XDM 352 features two convieniently located grounds Connect the ground lead of the turntable with this terminal This helps to reduce humming and popping noises 27 28 29 30 LINE PHONO INPUT JACKS Input jack for CH 1 CH 2 CH 3 and CH 4 Connect turntables equipped with MM pickup cartridge to PHONO inputs CD players or Tape Decks should be connected to LINE input Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to LINE inputs Channel 3 can be switched to 2 line inputs or 1 line 1 phono input by using the LINE 3 PHONO 3 selector 37 31 MASTER OUT Parallel output of P A output Connect with the input of power amplifier Make sure that the STEREO MONO switch 16 is set to STEREO 32 REC OUT Connect to your recording unit The REC OUT level is not influenced by the MASTER FADER 17 33 BOOTH OUT Connect your monitor system here 34 BALANCED OUTPUT Balanced output for the master signal Make sure that the STEREO MONO switch 16 is set to MONO American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 352 User Instructions page 4 PROformer Series Americaa OF o AUDIO Inputs and Outputs Cont 35 AC CONNECTION AC power cord 36 FUSE Fuseholder Only replace the fuse when the device is disconnected from mains Only replace by fuses of the same power and rating 37 AC VOLTAGE SELEC
3. individually and all possible combinations Connect your headphones to the PHONES jack 13 Turn the CUE MIXING control to CUE and select CH 1 CH 2 CH 3 or CH 4 with the CUE switches 5 The LED indicates which channel s have been chosen When you turn the CUE MIXING control to PGM CUE switches without function you can cue the output signal of the mixer If the CUE MIXING control is set to the center position you can cue both the channel signal you selected and the output signal With the CUE LEVEL control 12 you can adjust the phones volume without changing the output signal 12 CUE LEVEL CONTROL Adjusts the headphone output level 13 PHONES JACK Use this jack to connect the headphones Headphones from 8 Ohms to 600 Ohms can be used 16 Ohms is recommended American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 352 User Instructions page 3 PROformer Series Americaa OF o AUDIO Functions Cont 14 MASTER LEVEL DISPLAY The display shows the signal level of the master output on the left and right jack 15 BALANCE CONTROL Used to adjust how much of the signal is sent to the left and right MASTER OUT jack 31 16 STEREO MONO SWITCH Used to set the master output to mono or stereo If this switch is set to STEREO the master signal is sent to the MASTER OUT jacks 31 For mono and bridged operation set this switch to MONO and connect your amplifier with the 3 pin XLR
4. jacks on the rear panel BALANCED OUTPUT jacks 34 17 MASTER FADER Adjusts the level of the master output 18 EQUALIZER SWITCH Used to switch the equalizer on or off 19 7 BAND GRAPHIC EQUALIZER Used to fine tune the master output The frequencies are as follows 60Hz 150Hz 400Hz 1 KHz 2 4KHz 8KHz and 16KHz KHz They can be adjusted by 12 dB 20 MIC 1 JACK You can connect microphones with 6 3mm jack plug or XLR plug 21 BASS TREBLE Use these controls to fine tune the DJ MIC signal Increase the LOWs by turning the BASS control to the right Increase the Hi s by turning the TREBLE control to the right 22 TALKOVER SWITCH Use this switch if you want to use your microphone If the switch is set to ON all signals but the microphone level are attenuated by 15dB if the microphone is voice activated As soon as you start speaking the output level is reduced as soon as you stop speaking the output level is reset to the original level If the switch is set to TALKOVER the output signal is attenuated by 15dB After you stopped speaking you must manually set the TALKOVER switch to MICRO OFF The output level is then reset to the original level 23 MIC 1 LEVEL FADER Adjusts the microphone volume 24 BNC JACK FOR GOOSENECK LAMP Inputs and Outputs AAmecau DA o AUDIO 5606 DCA OOS 25 MIC 2 JACK Connect your second microphone with 1 4 inch 6 8mm jack plug here 26 26A GND Ground terminals
5. the input to be sent to the individual channel Channel 1 and 2 can be switched phono line Channel 3 can either be switched line line or phono line The selector is on the rear panel Channel 4 can be switched Mic2 line 4 CHANNEL FADER Used to adjust the output level of the individual channel 5 CUE SWITCH Used to select the channel s to be monitored 6 ASSIGN SWITCH Used to switch the crossfader on or off 7 CHANNEL ASSIGN SWITCH Used to select which channel is to be mixed with another 8 CROSSFADER Mixes the signals of one channel with another With the CHANNEL ASSIGN switches 7 you can choose which channel is to be mixed with another EXAMPLE Set the left CHANNEL ASSIGN switch to channel 1 and the right switch to channel 2 in order to mix the signal of channel with channel 2 When the crossfader is set to the center position both channels can be heard at once 9 BEAT INDICATOR The LED lights up at every bass beat of the respective source As soon as the LEDs blink synchronously the speed of the two sources Is synchronized 10 BOOTH LEVEL CONTROL THE XDM 352 features a DJ BOOTH monitor system Connect your monitor system to the BOOTH OUT jacks 33 on the rear panel You can adjust the output level with the BOOTH LEVEL knob 11 CUE MIXING CONTROL Selects the channel for monitoring The monitor signal comes from Prefader This means it will not be affected by the channel faders You can monitor every channel
6. TOR Make sure that the selector is properly set Replacing the Crossfader Instructions for replacing the crossfader e Disconnect from main power supply e Remove the fader knob e Remove the two outer screws e Take the fader out and unplug the connection cable e Connect the new fader and replace back into mixer Technical Specifications model XDM 352 mps o oS SSS SS Phono m 47kOhm Output 20V peak to peak control eee 10Khz 12dB eee 100 Hz 12dB 7 Band iaaa Equalizer 12dB at 60Hz 150Hz 400Hz 1KHz 2 4KHz 8KHz and 16KHz Headphone impedance 16 Ohms AC115 230V 50 60Hz 19 Wx 9 5 D x 3 25 H 482 x 242 x 108 mm 12 Tos 45 kg American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 352 User Instructions page 5
7. that the MIC 2 LINE 5 SWITCH is set to MIC 2 CAUTION You can only cut the MIC 2 Jack 25 off by setting the CHANNEL 4 fader to 0 or by switching the MIC 2 LINE 5 SWITCH to LINE 5 e You can connect 2 turntables using the PHONO 1 jacks 27 and PHONO 2 jacks 28 on the rear panel You can only control the turntables signal after you switched the PHONO LINE switches 3 to PHONO The signal is then controlled via the CH 1 and CH 2 faders 4 If you wish to connect a third turntable switch the LINE 3 PHONO 3 SELECTOR 37 on the rear panel to PHONO 3 You can only control the turntable signal after switching the PHONO 3 LINE 3 LINE 4 SWITCH 3 to PHONO 3 The signal is then controlled via the CHANNEL 3 FADER 4 e Connect your tape player tuner sound effects CD player cassette deck or any other line signals to the LINE jacks 27 28 29 amp 30 on the rear panel You can only control the line signals after switching the PHONO LINE switches 3 to LINE The signal is then controlled via the CH 1 CH 2 CH 3 and CH 4 faders 4 American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 352 User Instructions page 2 PROformer Series Americaa OF o AUDIO _ 0099 x I 1 a n A eoneeecocnoosess pide skes LE on Cee oe 1 POWER SWITCH 2 BASS TREBLE CONTROL Used to increase or decrease the LOWs and Hls of the input signal 3 LINE PHONO SWITCH Used to select
8. tion Damages caused by manual modifications to the device or unauthorized operation by unqualified persons are not subject to warranty There are no user serviceable parts inside the mixer For maintenance and or service contact an authorized American DJ dealer American DJ AUDIO Los Angeles CA 90058 USA Specifications subject to change without notice XDM 352 User Instructions page 1 PROformer Series Americaa OF o AUDIO Operating Determinations When installing this mixer please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around Doing so endangers you as well as others Do not operate the mixer in extremely hot more than 30 C 100 F or extremely cold less than 5 C 40 F surroundings Keep away from direct sunlight and heaters Operate the mixer only after becoming familiar with its functions Do not permit operation by persons not qualified for operating the mixer Most damages are the result of unprofessional operation Never use spray cleaners to clean the faders Never use solvents or abrasive detergents to clean the mixer It is recommended that you use a soft damp cloth Please consider that unauthorized modifications on the device are forbidden due to safety reasons Connections Refer to diagrams on pages 3 4 amp 5 e Make sure that the power switch 1 is set to OFF Before connecting other devices to the mixer all units have
9. to be switched off and the Master Control 17 set to min e Make sure that the available voltage is not higher than stated on the voltage selector 36 before connecting to power e In order to obtain the highest sound quality only use high quality American DJ Ameri Cable cables for connecting devices Make sure that the cables are properly fixed e Connect your amplifier to the MASTER OUTPUT jacks 31 Make sure that the channels are set properly L amp R For mono and bridged operation please use the BALANCED OUTPUT XLR jacks 34 and set the STEREO MONO switch 16 to MONO e Via the BOOTH OUT jacks 383 you can either connect monitor active speakers for the DJ booth an additional amplifier or a second zone e For recording connect your tape recorder or cassette deck to the REC OUT jacks 32 The REC OUT level will not be influenced by the master fader 17 You can set the output level with the channel faders 4 e The XDM 352 features two microphone inputs The Nuetrik connector jack 20 on the front panel is for 1 4 inch 6 3mm jack plugs and XLR plugs With the TALKOVER switch 22 you can attenuate all other signals without affecting the microphone volume You can switch Mic 1 Jack 20 off by setting the TALKOVER SWITCH to MICRO OFF The 1 4 inch 6 8mm MIC 2 jack 25 is on the rear panel You can connect your second microphone here Adjust the microphone volume by using the channel fader for CHANNEL 4 Make sure
Download Pdf Manuals
Related Search
Related Contents
SCHEDA LEGGI NUMERATE NUOVA Operating Instructions - CM113 Cent-a-Meter User Manual Throughput Testing Results Copyright © All rights reserved.
Failed to retrieve file