AEG 72640 Washer User Manual
Contents
1. Do not tilt the washing machine onto its front or onto its right side viewed from the front Electronic components can get wet Check the washing machine for transport damages A damaged unit must never be put into operation under any circumstances In the event of damage please contact your supplier Ensure that all parts of the transport safeguard are removed and that the unit is splash protected see Removing transport safeguard Otherwise the units or neighbouring furniture can be damaged when spinning Always insert the plug into a correctly installed earthed socket n the case of permanent connection A permanent connection may only be made by an authorised specialist Before putting the machine into operation ensure that the mains voltage and current type shown on the unit s rating plate correspond with those at the place where the machine is being installed The fuse rating is also found on the rating plate e Should work be carried out on the water supply installations in order to allow the machine to be connected properly to the water supply this work must be carried out by an authorised installer e Should work be carried out on the mains supply in order to allow the machine to be connected properly to the electricity supply this work must be carried out by an authorised electrician The mains lead may only be replaced by the customer service or by an authorised electrician Installation and connect2. e f multi component detergents are used the individual components were not used in the correct ratio If there are still grey spots on the washing Washing soiled with ointments grease or oils was washed with too little detergent Too lower temperature was used for washing A frequent cause is that softener particularly that in concentrated form has reached the washing Wash out such spots quickly and use the softener concerned carefully If at the end of the last rinse foam is still visible Modern detergents can also cause foam in the last rinse However the washing is still sufficiently rinsed If there are white remnants on the washing e These are insoluble components of modern detergents They are not the result of an insufficient rinsing effect Shake or brush out the washing In future perhaps you should turn the washing inside out before washing it Examine your choice of de tergent and if necessary use liquid detergent 35 Operating Instructions 36 Carrying out emergency drainage I 1 Fold open the flap in the right section Remove the emergency drainage hose Place the container under the hose Detach the plug of the emergency e f the washing machine no longer pumps off the washing solution emergency drainage must be performed e f the washing machine is in a room where there is a risk of frost emergency drainage must be performed if there is a possibility of fros
3. 022 874 33 00 Russia Electrolux Russia Ltd 16 Olympiysky prospekt 129090 Moscow Tel 095 937 7837 Fax 095 926 5513 Warranty conditions Customer service centres Israel Electricity amp Electronic Services Evis LTD 19 Hataasia st Raanana Industrial area 43654 Tel 972 9 7448118 Fax 972 9 7603618 e mail evis evis co il Japan Electrolux Japan Ltd Domestic Appliances Depart ment Maruzen Showa Warehouse Building Tookai 4 5 12 Ota ku 143 006 Tokyo Tel 0120 13 7117 Fax 03 3790 5257 Thailand OLYMPIA Thai Ltd 44 Ratchadapisek Road 10320 Bangkok Tel 2 513 6111 Fax 2 513 2574 Hungary Electrolux Lehel KFT AEG Div Erzs bet Kir lyn tja 87 1142 Budapest Tel 00361 467 3200 Malaysia Arzbergh Engineering No 49AJB Jalan Petaling Utama 7 4600 Petaling Jaya Tel 3 795 1084 Fax 3 795 1082 Singapore Arzbergh Engineering 19 Tanglin Road 06 07 Singapore 247909 Tel 65 7356572 Fax 7351124 Slovakia Rep Electrolux Slovakia S R O Seberiniho 1 821 03 Bratislava Tel 02 4333 4322 4355 Fax 02 4333 6976 USA ANDI Co Appl Inc East 65 Campus Plaza Edison New Jersey 0837 USA Tel 201 2258839 Saudi Arabia Alia Trading Corporation P O Box 4101 King Abdul Aziz Street Riyadh Tel 4645977 Al Nahas Est Musaidia Market P O Box 1 15 29 Jeddah Tel 6606852 Slovenia Electrolux Slovenia D O O Traska Ul 132 1000 Ljubljana Te
4. 40 C as stain removers only be come effective at higher temperatures The additional program cannot be selected with the V amp J WOOLLENS S Hand Wash setting any buttons pressed have no effect Operating Instructions Consumption values The values for selected programs in the following tables were determi ned under normal conditions However there is a helpful orientation aid for domestic operation Program selector temperature filling Quantity Warr Energy in kg in Litres in kWh kay COTTONS LINEN 90 5 45 1 70 kay COTTONS LINEN 60 1 5 42 0 94 kay COTTONS LINEN 40 5 49 0 60 tey EASY CARES 40 2 5 54 0 50 tJ DELICATES 30 2 5 50 0 30 16 WOOLENS amp Hand Wash 30 2 48 0 20 1 Note Program setting for a test in accordance with EN 60 456 The consumption values deviate from the stated values depending on the water pressure water hardness water inlet temperature room temperature washing type and quantity the detergent used fluctuations in the mains voltage and the selected additional functions What does UPDATE mean Your washing machine s washing programs are controlled by software New types of textiles or new detergents may require new washing pro grams in the future In most cases the software can be adapted to this For further information on the update please consult the Customer Service You can also enquire about the costs for an update with your Customer Service Operating In
5. COTTONS LINEN wy EASY CARES cl EASY IRON and Y DELICATES with any temperature Keep the VL PRE WASH and gt QUICK buttons pressed simultane ously for at least 2 seconds 1 RINSE lights up on the program sequence display The additional rinse is set It remains saved until you cancel it again Water consumption is increased due to the additional wash cycle Cancel additional rinse Again turn the program selector to ly COTTONS LINEN key EASY CARES I EASY IRON or Y DELICATES Keep the VL J PRE WASH and gt QUICK buttons pressed simultane ously for at least 2 seconds 1 RINSE goes out on the program sequence display The additional rinse is cancelled Operating Instructions Child Safety Feature If the child safety feature is set the filling door can no longer be closed and no washing program can be started Setting the child safety feature Use a coin to turn the rotary knob on the inside of the filling door clockwise as far as it will go Warning The rotary knob must not be in a vertical position after adjustment otherwise the child safety feature is not active The ro tary knob must project as shown in the diagram Cancelling the child safety feature Turn the rotary knob anticlockwise as far as it will go A NA 39 Installation and connection instructions 40 Installation and connection instructions Installation Safety Precautions
6. Out cu rw ep RR Xue 11 Q Quick wash 12 18 24 26 R Rating plate 0 9 45 55 Rinse hold 0000 11 19 25 Risk of frost 0 cece eae 6 36 RUN time oio ote pve a sa Vra 20 23 S SIE desc edit ebore P rada 11 15 Soaking 12 18 20 22 26 NA LANA o da 11 17 24 28 SPINNING epo rra a 19 SO cR 12 24 26 SEI oe o FAM s edP T 8 9 18 35 Stain removers e eee eee eee 22 Starching uses eer nep 11 28 U Updates sl LI Bana gag a A a DR 13 W Warranty ss saa ga Ga a 6 31 49 Washing Coloureds is apra ie em ias 14 lightly soiled ae 8 12 normally dirty aaa 8 Washing powder esses 9 Water hardness eruca lu 8 16 pump off scu lI LII ex xe 11 25 Softeners coul as 8 9 16 22 Woollens 11 15 27 28 hand washable 11 27 Service Service In the chapter What to do if some faults are listed which you can remedy yourself Look there first if a fault occurs If you do not find any information there please consult your Customer Service You can find the addresses and telephone numbers in the section Customer Service Centres Always prepare in advance for the discussion By doing so you will sim plify the diagnosis and the decision on whether customer service is necessary Note the PNC number and S num ber You will find both on the rating plate on
7. Sofia Tel 2 806676 Fax 2 980 5276 Cyprus Hadjikyrlakos amp Sons Ltd Prodromou 121 P O Box 21587 Nicosia 1511 Service Telephones Nicosia 02 481226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 Estonia Electrolux Estonia Ltd Mustam e tee 24 EE0006 Tallinn Tel 372 6 650 090 Fax 372 6 650 092 Hongkong Wo Kee Services Ltd 585 609 Castle Peak Road Kwai Chung N T Hongkong Tel 2494 4000 Korea South Core Incorp 3 F Chewoo Bldg 200 Nonhyun Dong Kangnam Ku Seoul Telefon 82 2 549 89 61 Croatia Electrolux D O O Suplova 7 10000 Zagreb Tel 1 61 19512 Fax 1 61 19513 Kuwait Arabian Gulf Ali Al Ghanim Est P O Box 10 83 Tel 5322463 Fax 5242114 Lebanon Adib amp Assaferi P O Box 539 Tripoli Latavia Electrolux Latavia Ltd Terlaton Street 42 44 1011 Riga Tel 371 2 297821 Fax 371 2 821286 Lthuania Electrolux Lthuania Verkui 29 2600 Vilnus Tel 372 272 3326 Fax 372 272 3366 Namibia AEG NAMIBIA PTY LIM ITED Jeppe Street Northern Industrial Area Windhoek Tel 061 21 6082 4 Fax 061 217838 New Zealand Euro Life New Zealand Ltd Privat Bag 58 Symonds Street Auckland Tel 09 525 2222 Nouvelle Caledonie Socometra N C B P 483 Nouman Tel 275444 Oman Moshin Haider Darwish P O Box 1 35 Muscat Tel 703743 Poland Electrolux Poland Sp zo o ul Domaniewska 41 02 034 Warszawa tel 022 874 33 33 fax
8. WASH Easy Cares ion E SOAKING sr 5 gt QUICK WASH z ou EASY IRON 1 kg m Gap STAIN 25kg UJ PRE WASH Delicates gt C3 DELICATES E SOAKING or rn 30 40 gt QUICK WASH curtains qj STAIN Operating Instructions Type of washing dr Program selector RIPSME yP 9 filling quantity 3 additional care symbol E temperature dry weight programs Woollens amp y HAND WASH Hand Wash 2 kg WOOLLENS O w Y XJ COLD to 40 1 The load amount inquiry operates in accordance with the EN 60456 standard load 2 A 10 litre bucket holds approximately 2 5 kg of dry washing cotton 3 QUICK WASH cannot be selected if washing at 50 C 4 In the case of the STAINS a minimum temperature of 40 C is required for the stain remover to become effective 5 Creases in the washing are only largely prevented if the filling quantity of 1 kg is maintained 5 to 7 easy care men s shirts are equivalent to approximately 1 kg of dry wash ing 27 Operating Instructions 28 Type of washing Cottons Linen Separate rinse Type of washing Cottons Linen Easy Cares Delicates Woollens Hand Wash Separate spin Type of washing Cottons Linen Easy Cares Delicates Woollens Hand Wash Max Filling quantity dry weight 5 kg Max Filling quantity dry weight 5 kg 2 5 kg 2 5 kg 2 kg Max Filling quantity dry weight 5 kg 2 5 kg 2 5 kg 2 kg Separate conditionin
9. e g water level drum movement number of rinses spin speed to suit the type of washing as well as the wash temperature O OFF Switches off the washing ma chine All other positions are switched on lay COTTONS LINEN Main washing cycle Cottons Linen Cottons Linen at 30 C to 95 C Du Position E ENERGY SAVING Energy saving programme at approx 67 C for slightly to normally dirty cottons extended washing time Cannot be combined with gt 4 QUICK WASH Operating Instructions key EASY CARES Main washing cycle for easy care textiles mixed fabrics at 40 C to 60 C Position EASY IRON Main washing cycle at 40 C for easy care textiles which with the aid of this program only have to be either gently ironed or not ironed at all KY DELICATES Main washing cycle for delicates at 30 C or 40 C J WOOLLENS amp y Hand Wash Main washing cycle J cold to 40 C for machine washable woollens and for woollen textiles and silk with the care symbol Vu Hand Wash A GENTLE RINSE Separate gentle rinsing e g for rinsing hand washed textiles 2 rinsing cycles liquid care agent from compartment amp 9 is rinsed in short spin B STARCHING Separate starching separate conditioner separate impregnation of damp washing 1 rinsing cycle liquid care agent from the compartment 88 is rinsed in spin C PUMP OUT Pumping out the water after a rinse hold without spin CJ Rin
10. plug Clean the solution pump Clean the siphon Wait until the o DOOR dis play lights up green If it is still necessary to open the filling door turn the program selector to OFF turn the program selector to C PUMP OUT Press the D amp 2 START PAUSE button After the water has been pumped out the filling door can be opened If water can be seen through the window in the door first carry out emergency empty ing see section Carrying out Emergency Emptying Opera tion After approx 4 to 10 minutes the door can be opened again by pulling the handle Open the water valve fully Close the water valve Un screw the intake hose from the water tap and from the unit Clean the filter Operating Instructions Problem Possible Cause Remedy The cause is probably a de No negative effect on the tergent with a high silicate rinsing result use liquid de content tergent if necessary The rinsing water is murky The corresponding dis play does notlight up The selected additional pro when one of the addi gram cannot be combined Make another selection tional program but with the set program tons is pressed If the washing results are not satisfactory If the washing has turned grey and if limescale is deposited in the drum then Too little detergent was used he wrong detergent was used Special soiling was not pre treated Program or temperature not set correctly
11. the package is sufficient Water hardness details Water hardness in dH Water hardness in mmol Hardness class M a German hardness scale millimol per litre soft 0 7 to 1 3 Il medium hard 7 14 1 3 2 5 111 hard 14 21 2 5 3 8 IV very hard greater than 21 greater than 3 8 Operating Instructions Run a washing cycle Brief instructions I 1 NO on 5 WN A washing cycle is run in the following steps Set the correct washing program Set the program and temperature with the program selector Set any additional program s If necessary change the spin speed select TJ RINSE HOLD Set the d DELAY TIMER if necessary Open the filling door and fill with washing Close the filling door Add the detergent care agent Start the washing program with the lt gt START PAUSE button After the washing program ends Important If the washing cycle ended with a rinse hold perform C PUMP OUT D SPIN or F SHORT SPIN before opening the filling door Open the filling door and remove the washing Switch off the washing machine Set the program selector to OFF 17 Operating Instructions Setting the Washing Program T p 1 For the suitable program the correct temperature and possible addi tional programs for the particular washing type refer to the Program tables Set the program selector to the required washing program with the required te
12. the inside of the door of your washing machine PNG Na S NO iste mE Answer as precisely as possible What form does the fault take Under what circumstances does the fault occur Does the multi display show an error message When do you incur costs even during the warranty period f you could have remedied the fault yourself with the aid of the fault table see the section What to do if If several journeys by the customer service technician are necessary because for example he did not receive all the important information before his visit and must collect spare parts These multiple trips can be avoided if you prepare your phone call as described above 55 E From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de 9 Copyright by AEG 822 943 145 01 310303 03 Subject to change without notice
13. OKO LAVAMAT 72640 update The environmentally friendly washing machine User information Dear Customer Please read this user information carefully Pay particular attention to the section Safety on the first Info pages Please keep this user information in a safe place for later reference Pass it on to any future owners of the unit The warning triangle and or signal words Warning Caution Impor tant emphasise information which is important for your safety or for the unit s functional reliability It is imperative that this information is observed his symbol guides you step by step through the operation of the appli ance Next to this symbol you will find additional information and practical tips on using the appliance Tips and information on economical and environmentally responsible use of the unit are identified with the clover leaf For any faults which occur this user information contains information on how to remedy these faults yourself See the section What to do if Printed on recycled paper Thinking ecologically means acting ecologically Contents Operating Instructions eee 6 STI A EET 6 Disposal 2 n RE URS 8 Environmental tips eee eea eee 8 Unit description iioii ee Gan PP ERG On 9 Front VIEW air racist Der Og Ei eric p ar du tae KON ar ad 9 Drawer for detergent and Care agent eee eee eee 9 Control panel r
14. Uy PRE WASH SOAKING or for water softener Push the drawer fully in If using liquid detergent tabs Add liquid detergent tabs in the amount recommended by the was hing detergent industry Follow the instructions on the washing deter gent package Operating Instructions Start the washing program t 1 Check that the water valve is open i 2 Start the washing program Press the lt gt START PAUSE button The washing program is started or it Q Q o Q starts after the set time expires The filling door is not correctly closed if the o DOOR display flashes red when the Q START PAUSE button is pressed The display o DOOR flashes red The error code EMG then flashes in the multi display And the VJ MAIN WASH display flashes In this case press the filling door firmly closed and again press the lt D O START PAUSE button If the time preselection is set The set delay time runs The remaining time to the program start is shown in the multi display in each case full hours e g 5h During this time you can load washing or change abort the time preselection e Load washing Press the lt gt START PAUSE button The filling door can be opened Then close the door and press the DJ START PAUSE button again e Change or abort time preselection Press the d DELAY TIMER but ton as often as necessary until the required time is displayed When the program run time is
15. aaa eee 45 Water inflow sasarapan ana apana palapa Ni ag Ba a aka aa a an pe a an a Ba kaa Esai 46 Water drain cere era ete xem RD RC Pera ah eds 47 Delivery heads over 1m eissira nanena a eee 47 Technical data cree Paes Wee nuce eb eed 48 DIMENSIONS pev eee Y RN A Lee NG 48 Warranty conditions Customer service centres 49 dio sence etter leia 54 Operating Instructions Operating Instructions N Safety The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law However as manufacturers we regard it as our responsibility to inform you about the following safety instructions Before Using for the First Time Refer to the Installation and Connection Instructions further on in this user information e f units are delivered in the winter months at minus temperatures Store the washing machine at room temperature for a few hours be fore putting it into operation Correct Use The washing machine is only intended for washing normal domestic washing If the appliance is used for a wrong purpose or wrongly op erated the manufacturer cannot assume any liability for any dam ages Additions or modifications to the washing machine are strictly for bidden due to safety reasons Use only detergent which is suitable for washing machines Refer to the detergent manufacturer s instructions he washing must not contain any flammable s
16. ally dirty cottons with the energy saving pro gram There is often no need for the softener Try it once If you use a drier your washing will become soft and fluffy even without a softener n the case of medium to high water hardness hardness range runs to upwards see Detergent and care agents you should use a water softener The detergent can then always be metered for hardness range soft Operating Instructions Unit description Front view Drawer for de tergent and care agent Control panel Rating plate be Screw feet height adjustable Drawer for detergent and care agent Stain removers Main wash detergent powder form and i m i hind filling door Main door Flap in front of drain pump Pre wash detergent soaking agent or water softener Liquid care agents possibly water softener conditioner finisher starch Operating Instructions Control panel Spin speed RINSE HOLD button Additional program buttons DOOR Indicator Program sequence display Program selector Button DELAY TIMER uyo O 1200 ro 1000 uyo Ol ze eC wes sO 33 Emo S we O B ve Q Do m f Be x i Multi display OVER DOSING display START PAUSE button Program selector The program selector defines the nature of the washing cycle
17. conditioning starching impregnation s 28 Separate rinse ian kk sete eR MR BUDE IP BU ER 28 Sep rate SHIA me 28 Cleaning and Care Rs 29 Control panel cine eesti aes ease teenie a is WE PIG 29 Detergent Drawer once reete dan ge extent gaps 29 Washing Drum ii cus rr ri Gee pen prc oa fonde dg 30 Main dO Ot La saa a a pee IM ecu re e ote ad ecu epa wet 30 What to dO if ror pee an ins px COEM ol re d 31 Remedying faults ss sese e eed ea rei e ke eae ane 31 If the washing results are not satisfactory a cece eee 35 Carrying out emergency drainage aaa eaaa 36 Drain DUMP tir e pe eee De ego a evt gs 37 Additional Rinse 1E RINSE 00 0 0 cece ee eee eee eee 38 Child Safety Feature 0 39 Installation and connection instructions 40 Installation Safety Precautions eee 40 Installation of the appliance 0 0 0c cece eee 41 Transporting the appliance 2 eee eee eee 41 Remove transport packaging 6 0 cece eee eee ee 41 Prepare the installation place aee eee 43 Installation on a concrete base eaaa ee 43 Installation on vibrating floors cee eee 43 Compensate for floor unevenness 22000 cece eects 44 Electrical connection ssesesnn RR 45 Water connection sisa ma ds guna a gae Gan Gana i a BG Ja A a ga 45 Permissible water pressure_ a aaa e
18. connecting to cold water must not be connected to hot wa ter Use only new hose sets for the connection The water pressure must be at least 1 bar 10 N cm 0 1 Mpa max imum 10 bar 100 N cm 1 Mpa f more than 10 bar Connect a pressure reduction valve upstream e f less than 1 bar Unscrew the inlet hose on the unit side at the sole noid intake valve and remove the flow regulator to do this remove the filter with pointed pliers and take out the rubber washer behind Replace the filter 45 Installation and connection instructions 46 Water inflow Co Connect the hose with the angled connection to Connect the hose with the By slowly opening the water valve before A pressure hose of 1 35m in length is supplied If a longer inflow hose is required only a VDE approved complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible Hose sets in lengths of 2 2m 3 5m and 5m are available for washing machines without Aqua Control Hose sets in lengths of 2 0m 2 9m and 3 5m are available for washing machines with Aqua Control Important Never cut into pieces in order to extend the hoses Sealing rings are supplied either in the plastic nuts of the hose screw connection or in the enc losed pack Do not use other seals the machine Important Do not lay the inlet hose verti cally downwards instead run it to the ri
19. curely Remove the two screws E with the special spanner A Remove the 4 screws F Remove the transit bar C Screw the 4 screws F back in for safe keeping Close the 2 large holes with the caps B Important When fitting the plastic caps press until they snap into the rear panel securely Installation and connection instructions Prepare the installation place e The installation surface must be clean and dry free of floor polish residues and other greasy coatings so that the unit does not slip away Do not use lubricants as a sliding aid Installation on a high veil carpet or floor tiles with soft sponge backs is not recommended because the standing safety of the appliance is then no longer ensured e By installation surfaces with small format tiles lay a conventional rubber mat underneath Minor unevenness of the floor surface should never be levelled out by laying pieces of wood card or similar materials but rather should al ways be compensated for by adjusting the screw feet e f for space reasons it is not possible to avoid setting up the unit di rectly next to a gas or coal fired cooker install a thermal insulation panel between the cooker and washing machine 85 x 57cm which must have an aluminium film on the side against the cooker e The washing machine must not be set up in a room where there is a danger of frost Frost hazard e Flexibl
20. dditionally be selected after the program starts Press the START PAUSE button Press the lt gt START PAUSE button again The washing program is continued Change the Spin Speed During the washing program the spin speed can still be changed or CJ RINSE HOLD can be set Press the lt gt START PAUSE button Change the speed with the Spin speed L RINSE HOLD button Press the gt START PAUSE button again The washing program is continued Operating Instructions The washing cycle is finished Remove the washing After a washing program has ended gt END lights up on the program sequence display If CJ RINSE HOLD was selected the display next to the START PAUSE button flashes ts 1 After a rinse hold it is first necessary to pump off the water Either press the lt gt START PAUSE button the water is pumped off the and the washing is spun according to the finished program After the lt gt START PAUSE button is pressed again the spin speed can still also be changed during spinning or Turn the program selector to OFF and then to C PUMP OFF and press the lt gt START PAUSE button the water is pumped off without spinning or Turn the program selector to OFF and then to D SPIN or F SHORT SPIN and press the lt gt START PAUSE button the water is pumped off and the washing is spun or gently spun After the end of this progra
21. displayed display in minutes e g 26 the washing can start without a delay Completion of the Washing Program Program sequence display Uyo Before the start the program steps to be carried out W are indicated by the Program sequence display The o current program step is displayed during the washing e program Go gt Multi display 1 o The expected remaining run time in minutes is displayed in the multi display until the end of the program With automatic program adaptation by the controller of the washing machine quantity of washing type of washing imbalance recognition special rinse etc it is possible to stop or correct the counting of the re maining run time 23 Operating Instructions 24 Change program Ux 1 Press the SHORT or f STAIN button 3 3 Changing or aborting the program Press the lt gt START PAUSE button Turn the program selector to OFF The washing program is aborted If required set a new washing program Otherwise turn the program selector to C PUMP OUT and press the gt START PAUSE button The washing program can be interrupted at any time with the O START PAUSE button and can be continued by pressing the button again Changing the washing program is only possible after the pro gram selector has been turned to O OFF Select the additional program The additional programs gt 4 QUICK or 3 STAIN can still a
22. e favourably distributed during spinning e Fluff washing before placing into the washing machine Do not place folded washing into the drum e Pay attention to the care instruction wash separately and wash separately several times Operating Instructions Washing Types and Care Symbols The care symbols help you chose the correct washing program The washing should be sorted according to type and care symbol The tem peratures shown in the care symbols are the maximum temperatures in each case Cottons Textiles made of cotton and linen which carry this care symbol are in sensitive to mechanical stress and high temperatures The programm ley COTTONS LINEN is suitable for this type of washing Linen Textiles made of cotton and linen which carry this care symbol are in sensitive to mechanical stress The programm ky COTTONS LINEN is suitable for this type of washing Easy care washing Textiles such as treated cotton cotton mixed fabrics viscose and syn thetics which carry this care symbol require chemically more gentle treatment The program wy EASY CARES I EASY IRON is suitable for this type of washing Delicates Textiles such as layered fabrics micro fabrics viscose synthetics and cur tains which carry this care symbol require particularly gentle treatment The program Y DELICATES is suitable for this type of washing Wool and especially sensitive washing wi Textiles such as wool wool mixture
23. e feed and drain tubings may not be crinkled or squeezed Installation on a concrete base If the unit is set up on a concrete base for safety reasons it is essential to fit stand plates in which the washing ma chine is adjusted The stand plates are available from Customer Service under the spare parts number 645 425 058 O Installation on vibrating floors Where the floor vibrates particularly in the case of wooden beam floors with pliable boards securely screw a water resistant wooden panel at least 15mm thick onto at least 2 floor planks If possible set up the unit in the corner of a room as the wooden floor is optimally re strained there and is therefore least likely to be subject to resonance vi brations 43 Installation and connection instructions 44 Compensate for floor unevenness is 1 Adjust the screw feet so that the If necessary check the setting Floor unevenness can be compensated for and the height can be cor rected with the four adjustable screw feet The height can be adjusted in the range 10 5mm To adjust the feet use the special spanner supplied for removing the transport braces Slide the special key firmly onto the hexagon head of the threa ded foot as far as it will go unit is horizontal and stable The unit must not wobble over when loaded with a spirit level Important Minor unevenness
24. el wool Our Customer Service can provide suitable agents ts Remove any rust deposits on the drum using a stainless steel cleaning agent Main door t Check ona regular basis to see if deposits or foreign objects are present in or at the rubber sleeve behind the door and remove 30 Operating Instructions What to do if Remedying faults In the event of a fault try to solve the problem yourself with the aid of the information provided here If you use the Customer Service to rem edy one of the faults listed here or to remedy an operating fault the customer service technician s visit will be subject to a charge even dur ing the warranty period e f the fault code E 3 E20 or EMB is shown in T1 the multi display you may be able to remedy the uis fault yourself see the Faults table below After remedying the fault press the Q START PAUSE button If the fault code is displayed again inform the Customer Service e n the case of all other displayed faults E and number or letter please inform the Customer Service stating the fault code Problem Possible Cause The mains plug is not plugged in The fuse of the building s wiring is not in order The washing machine does not work The filling door is not cor rectly closed START PAUSE but ton not pressed long enough Filling door cannot be The child safety feature is set closed The fault code ENG ap pears The disp
25. g starching impregnation Program selector B STARCHING Program selector A GENTLE RINSE Program selector D SPIN F SHORT SPIN Operating Instructions Cleaning and Care Control panel Important Do not use any furniture cleaning agents or aggressive cleaning agents in order to clean panel and control parts Wipe control panels with a damp cloth When doing so use warm wa ter Detergent Drawer SS 1 2 3 4 Clean the compartments with warm The detergent drawer should be cleaned from time to time Pull the detergent drawer out as far as it will go Remove the detergent drawer by pulling sharply Take the conditioner insert out of the middle compartment Clean the conditioner insert under running water water from the rear side It is best to use a flat brush Push on the conditioner insert as far as it will go so that it is securely in place 29 Operating Instructions 7 Use a brush to clean the entire rinsing in section of the washing machine particularly also the noz zles on the top side of the rinsing in chamber 8 Set the detergent drawer into the guide tracks and push in Washing Drum The washing drum is made of stainless steel Rusting foreign bodies in the washing can cause rust deposits on the drum Important Do not clean the stainless steel drum with decalcifying agents containing acids scouring agents containing chlorine or iron or ste
26. ght or left as shown in the diagram Tighten the hose screw connec tion only by hand straight connection to a water valve with a screw thread R 3 4 inches Important Only tighten the screw connection manually putting the washing machine into operation check that the connection is free of leaks Installation and connection instructions Water drain The drainage hose can either be connected to a siphon or hung in a wash basin or discharge basin or a bath tub Only original hoses may be used for extensions max 3m laid on the floor and then up to 80cm high Customer Service stocks drainage hoses in lengths of 2 7 and 4m Important It is essential to lay the drainage hose without kinks Water drain off inside a siphon The grommet on the hose end fits all standard siphon types Eg Secure the connection between the grommet and siphon with a hose clamp Water drain off inside a basin Important Small basins are not suitable for drainage Water could overflow The end of the drainage hose must not be submerged in the pumped out wa ter Otherwise the water could be sucked back into the unit When hanging in a wash basin or a bath tub the drainage hose must be secured with the supplied attachable bend to prevent it slipping The back surge force of the escaping water could otherwise force the hose out of the basin gt Tie the bend to the tap or the wall using a
27. in pump Operating Instructions Small animals can chew the power cables and water hoses Risk of electric shock and danger of water damage Keep small animals away from the washing machine e Disposal Disposing of the Packaging Material Dispose of the packaging of your washing machine correctly All pakka ging materials used are environmentally compatible and recyclable Plastic parts are identified with internationally standardised abbrevi ations gt PE lt for polyethylene e g packing films gt PS lt for polystyrene e g cushion parts always CFC free gt POM lt for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposing of your old appliance When you put your unit out of operation one day please bring it to your nearest recycling centre or to your dealer el Environmental tips e A pre wash cycle is not necessary in the case of washing which is not excessively dirt This saves detergent water and time and is gentle on the environment e f the indicated load capacities are taken full advantage of the wash ing machine is especially efficient For small loads use only one half to one third of the recommended detergent quantity e Suitable pre treatment enables marks and limited amounts of dirt to be removed You can then wash at a lower temperature e Wash slightly to norm
28. ion instructions Installation of the appliance E Washing machines with curved panels are not suitable for installing under units Transporting the appliance Do not place the washing machine on its front or on its right side viewed from the front Otherwise electrical components can get wet e Never transport the unit without the transport safeguard Do not re move the transport safeguard until the appliance is at the installation location Transporting the unit without the transport safeguard can damage it e Lift the appliance neither by an open filling door nor by the base When transporting the unit with a sack trolley Attach the sack trol ley only at the side Remove transport packaging Important It is essential to re move the transport packaging be fore putting the appliance into operation Keep all parts of the transport packaging in a safe place for future use t 1 Open both hose holders on the appliance s rear side and remove the hoses and mains cable 2 Pull both hose holders off the ap pliance with a strong pull 41 Installation and connection instructions 42 i The special spanner A and the caps B 2 each and C 1 each are supplied with it Remove the screw D including the compression spring with the special spanner A Cover the hole with the cap C Important When fitting the plastic caps press until they snap into the rear panel se
29. ispose of the plug and remaining cable This means that playing children cannot shut themselves in and cannot encounter a potentially lethal hazard General Safety Repairs to the washing machine may only be carried out by qualified specialists Incorrect repairs may result in significant risk to the user If repairs are necessary consult our customer service or your special ist dealer Never use the washing machine if the mains cable is damaged or the conrol panel work surface or base panel area are so badly damaged that the interior of the unit is openly accessible Switch off the washing machine before carrying out cleaning care and maintenance work Also pull the mains plug out of the socket or if it is permanently connected switch off the circuit breaker at the household power distribution box or completely remove the screw in fuse e f operation is stopped disconnect the appliance from the mains sup ply and shut off the tap Never pull the cable to remove the plug from the socket Always pull the plug itself Multiple connectors couplings and extension cables must not be used There is a risk of fire with overheating Do not spray down the washing machine with a water jet Risk of electric shock e The glass in the door becomes hot in the case of wash programmes with high temperatures Do not touch Allow the washing solution to cool before carrying out an emergency emptying operation or cleaning the dra
30. ities see the Program tables See Sort and prepare washing for information on correctly preparing the washing Sort and prepare the washing according to type Open the filling door Pull on the handle of the filling door Fill with washing Important When closing the door make sure no items of washing get stuck This could damage textiles and the unit 21 Operating Instructions 22 Add detergent care agent T is 1 Open the detergent drawer grip inside Filling with washing detergent For information on detergent and care agents refer to the section De tergents and care agents the flap on the drawer at the bottom 1 and pull out the drawer as far as it will go 2 care agent Compartment for in wash stain treatment 4 Compartment for powder main detergent If you use water softener and require the right compartment for the pre wash soaking detergent add the water softener to the main detergent in the left compartment Compartment for liquid care agent Softener finisher starch Important Fill the compartment at most to the MAX mark Fill any viscous agent up to the MAX mark Dissolve powdery starch Note It is normal for a small amount of water to be left in the compartment for liquid care agent this will not affect the wash results Compartment for pre wash soaking detergent Only for auxiliary programs
31. l 61 1234 137 Fax 61 1234 238 South Africa AEG Pty Ltd 55 12th Road P O Box 1 02 64 Kew Johannesburg 2000 Tel 8069111 Syria Masri amp Shami P 0 Box 24 96 Damascus Tel 214080 51 Warranty conditions Customer service centres 52 53 Index 54 Index A Abort program eaaa C Car agent tec estu Wa aa aaa ain aa Change program aaa Child safety feature 31 Clothes sensitivVe_ ai Conditioner 9 11 16 17 22 CO crias ea 10 15 26 Curtains 220 2 4 lud cada 14 Customer Service 13 30 31 D Delay timer 10 12 20 Delicates 000005 11 15 Detergent 204 9 16 17 Detergent dispenser drawer Detergent drawer a Drain pump kaka 9 E Easy OM seo bobo Dre t c 11 15 26 Easy CareS sa age E an ea a 11 15 Emergency drainage Energy saving eaaa 10 F Fabricisoftenel croacia ova Filling quantity a 13 G Gentle Tinsin datang aa E a uniri 11 H Hand wash sss 11 27 In wash stain treatment L linen coi 10 15 26 M Multi display 10 20 23 31 0 Open the door 21 25 Over dosed aaa P Pre wash 12 18 20 22 26 Pre wash detergent 9 22 Program sequence display 10 23 Pump
32. lay The filling door is not cor VJ MAIN WASH rectly closed flashes Remedy Plug in the mains plug Replace the fuse Close the filling door The lock must engage audibly Press the 4 amp 2 START PAUSE button until the pro gram begins Cancel the child safety fea ture see Section Child Safety Feature Close the filling door cor rectly Restart the program 31 Operating Instructions 32 Problem Water is not running The fault code E iG ap pears The display RINSE flashes The washing machine vibrates during opera tion or it is on an une ven surface The washing solution of the main wash froths up a lot Possible Cause Water valve closed Filter in screw connection of the intake hose blocked Water tap is blocked with limescale or is faulty The transport packaging has not been removed The height adjustable screw feet are not correctly set There is not much washing in the drum e g only one dressing gown The water could not be com pletely pumped off before spinning because The drainage hose is bent or The solution pump is blokked Too much detergent was probably used Remedy Open the water valve Close the water valve Un screw the hose from the tap remove the sieve and clean under running water Check water tap and have it repaired if necessary Remove transport packaging according to the installation and connection i
33. lips nails etc which may find their way into the washing ma chine along with the washing will remain in the drain pump housing To restart the drain pump when it is blocked please proceed as follows N Warning Switch off the washing machine and remove the mains plug before cleaning the drain pump t 1 First carry out an emergency emptying procedure see section Carrying out emergency emptying 2 Place a cloth on the floor in front of the cover of the drain pump Residual water may run out 3 Unscrew the drain pump cover in an anti clockwise direction and pull it out 4 Remove any foreign objects and fabric lint from the pump housing 37 Operating Instructions 38 5 Replace the pump cover Laterally insert 6 Close the emergency emptying hose and 7 Close the flap the webs on the cover into the guide slots and screw on the cover in a clock wise direction place it in the holder Additional Rinse RINSE i is 1 kado I 1 The washing machine is set for extremely economical water consump tion However for persons who suffer from allergies it can be helpful to rinse with more water If 2J RINSE is set an additional rinse is carried out with the pro gram ky COTTONS LINEN key EASY CARES T EASY IRON and wy DELICATES No additional rinse is set when the unit is delivered Set additional rinse Turn the program selector to k
34. ll mismo Ulteriori uffici del servizio tecnico assistenza clienti all estero In questi paesi sono valide le condizioni di garanzia dei partner locali Queste condizioni possono essere esaminante sul luogo Servicos de assist ncia t cnica no estrangeiro Nestes paises s o v lidas as condi es de garantia dos concession rios locais podendo a ser consultadas Tov bbi vev szolg lati irod k k lf ld n Ezekben az orsz gokban a mi AEG vev szolg latainkn l saj t j t ll si felt telek alka Imazhat k A tov bbi adatokat k rj k k zvetlen l szerezz k be U A E Abu Dhabi Jordan Malta Universal Trading Company Jordan Household ITC P O Box 43 99 Supply Co Ltd International Trading Com Tel 335331 P O Box 3 68 pany Amman Tel 69 70 50 White House Building Mountbatte Street Blata L Bajda Tel 220644 Egypt Kanada Mauritius Middle East Commercial EURO LINE Appliances Happy World Centre Ltd Center 2150 Winston PARK Drive 20 P O 7 54 P O Box 19 Oakville Ontario L6H 5V1 1 Chausee Street Kairo Heliopolis Tel 905 829 3980 Port Louis Tel 29917 31634 Fax 905 829 3985 Tel 25355 Warranty conditions Customer service centres 50 Australia ANDI Co Pty Ltd 9 Kingston Town Close Oakleigh VIC 3166 Tel 03 9569 1235 Fax 03 9569 1450 Bahrain Arabian Gulf A A Zayani amp Sons P O Box 9 32 Bahrain Tel 261060 Bulgaria Electrolux Bulgaria E O O D 91 Levski Blvd 1000
35. m step the gt END indicator will illumi nate 2 Open the filling door As soon as the DOOR indicator lights up green the filling door can be opened Remove the washing Turn the program selector to OFF Close the water valve After washing pull out the washing detergent drawer slightly so that it can dry out Only lean the door against the washing machine so that the latter can air out If the indicator C OVERDOSING lights up too much deter Po gent was used in the washing program just ended Observe the dosing recommendations of the detergent manufacturer as well as the filling quantity for the next wash Important If the washing machine is not used for a long time Close the water tap and disconnect the washing machine from the electricity mains oc amp ry 25 Operating Instructions 26 Program tables Washing Not all possible settings are listed below only those which are normal and appropriate in everyday use Type of washing uo Program selector sale yP Ji filling quantity 3 additional care symbol temperature dry weight programs U PRE WASH Cottons A key COTTONS LINEN Ej SOAKING 9 95 gt QUICK WASH P STAIN Energy saving UU PRE WASH program 5 kg ESAS LINEN E SOAKING Cottons f STAIN UJ PRE WASH Linen EN kay COTTONS LINEN E SOAKING 9 30 to 60 gt QUICK WASH GP STAIN 2 5 kg E EASY CARES UJ PRE
36. mperature The probable duration of the set program in minutes is shown in the multi display If necessary select additional program s uJo The display of the selected auxiliary program lights up To change the selection press another button ty To deselect press the button again Operating Instructions Changing the spin speed Selecting the rinse hold function kei If required change the spin speed for the final sonic rinse hold EN idus 1000 Changing the spin speed 900 O Continue pressing the spin speed X 7 RINSE 700 O HOLD button until the indicator for the desired 400 O spin speed is illuminated wo If you do not change the spin speed the final spin will be adjusted automatically depending on the type of wash cycle VJ COTTONS LINEN 1200 revolutions per minute key EASY CARES I EASY IRON 900 revolutions per minute 4 DELICATES 700 revolutions per minute J WOOLLENS amp Hand Wash 900 revolutions per minute The speed for the intermediate spin cycle is dependent on the wash cy cle selected and cannot be altered Selecting the rinse hold function Continue pressing the spin speed I RINSE HOLD button until the indicator J RINSE HOLD for the desired spin speed is illuminated If CJ RINSE HOLD is selected the washing will remain in the final rinse water and will not be spun The washing will not be spun throughout the entire
37. nstructions Adjust the feet according to the installation and connec tion instructions This does not impair the op eration of the machine Check the laying of the drainage hose and eliminate the bend if necessary or clean the solution pump and if required remove foreign bodies from the pump hous ing Meter the detergent exactly in accordance with the man ufacturer s information Operating Instructions Problem Water runs out under the washing machine Conditioner was not washed in compart ment amp for care agents is filled with water Washing heavily creased The washing has not been spun as dry as usual Possible Cause The screw connection on the intake hose is leaky The drainage hose is leaky The washing solution pump cover is not correctly closed Washing is trapped in the filling door The emergency drain hose is not correctly closed or is leaky The conditioner insert in the compartment for the care agent is not correctly at tached or is blocked Too mush washing probably put in The washing was not able to be distributed evenly in the drum prior to spinning Remedy Tighten the intake hose screw connection Check the drainage hose and replace it if necessary Close cover correctly Abort the program and re move the washing through the filling door Restart the program Close the emergency drain hose correctly see the sec tion Carrying ou
38. of the floor surface should never be levelled out by laying pieces of wood card or similar materials but rather should always be com pensated for by adjusting the adjustable feet Installation and connection instructions Electrical connection CE Water connection i Permissible water pressure Details of the mains voltage current type and required fuses can be found on the rating plate The ra ting plate is located at the top above the filling door For permanent electrical connection within the electrical circuit provi sions must be made which allow for electrical disconnection of the ap pliance from the mains with a contact opening of at least 3 mm at all poles Suitable devices include circuit breakers fuses threaded fuses must be entirely removed from the socket ground fault circuit inter rupters and contactors Permanent connection may only be carried out by an authorised electrician This appliance complies with the following EC directives The Low Voltage Directive 72 23 EU with changes The EMC Directive 89 336 EU with changes The washing machine has safety features which prevent back contami nation of the drinking water and which conform to the national regu lations of the water authorities e g for Germany DVGW guidelines This means that additional protective measures in the installation are not necessary Important Units for
39. olvents Also bear this in mind when washing pre cleaned washing Do not use the washing machine for dry cleaning Dyes dye removing agents may only be used in the washing machine if the manufacturer expressly permits use of these products We can not accept liability for any damage e Use only water from the water mains Use rain water or service water only if it meets the requirements defined in DIN 1986 and DIN 1988 e Frost damage is not covered by the warranty If the washing machine is in a room subject to possible frost hazards emergency emptying must be carried out if there is a risk of frost see the Section Carry ing out emergency emptying Operating Instructions Safety of Children and Infirm Persons e Packaging materials e g films polystyrene can be dangerous for children Risk of suffocation Keep packaging away from children The appliance is not intendet for use by young children or infirm per sons without supervision Children frequently cannot recognise hazards involved in handling electrical appliances Therefore ensure that they are properly super vised during operation and never allow children to play with the washing machine there isa risk that they can lock themselves inside it Ensure that children or small animals do not climb into the washing machine s drum When disposing of washing machines pull out the mains plug destroy the door lock cut off the electrical supply lead and d
40. piece of string Delivery heads over 1m To pump off the washing rinsing solution every washing machine has a drain pump which carries liquids up to a height of 1m via the drain age hose calculated from the machine s standing surface Please contact Customer Service for delivery heads of over 1m 47 Installation and connection instructions 48 Technical data Adjustment possibility Filling quantity program dependent Area of use Drum speed spinning Water pressure Dimensions dimensions in mm 10 8507 Approx 10 5mm max 5kg Domestic See rating plate 1 10 bar 10 100 N cm 0 1 1 0 Mpa Warranty conditions Customer service centres Warranty conditions Customer service centres Weitere Kundendienststellen im Ausland In diesen Landern gelten die Garantiebedingungen der rtlichen Partner Diese k nnen dort eingesehen werden Further after sales service agencies overseas In these countries our AEG agents own guarantee conditions are applicable Please ob tain further details direct Autres agences trang res assurant le service apr s vente Dans ces pays les conditions de garantie des concessionnaires de la r gion sont vala bles Vous pouvez les consulter sur place Otros puntos de Postventa en el extranjero En estos pa ses rigen las condiciones de nuestros representantes locales las cuales pueden ser consultadas a
41. roximately 2 seconds the multi display n O shows the run time in minutes do C This run time is made up as follows Selected soaking period e g ih 60 Minutes Heating up pre wash time e g Approx 20 Minutes Run time of the selected wash program e g Approx 126 Minutes Displayed value e g Approx 206 Minutes While EY SOAKING is running LU PRE WASH lights up on the program sequence display Operating Instructions Opening and closing the filling door pe p Add Close the filling door securely Open Pull on the handle of the filling door ro Close Press the filling door firmly closed The displays o DOOR and lt gt START PAUSE show D Q o O when the unit is switched on whether the filling door can be opened Display o DOOR Display lt gt START PAUSE Door opening possible lights up green flashes red Yes 1 yes after the Q START lights up green lights up red PAUSE key is pressed Eoi flashes red n or lights up red 1 Filling door is locked because of a high water level or high temperature If the display o DOOR flashes red then the error code EG flashes in the multi display and the display VJ MAIN WASH flashes an attempt was made to start a washing program without the filling door being correctly closed In this case press the filling door firmly closed and start the washing program again the washing For the maximum filling quant
42. s and silk which carry this care sym bol are particularly sensitive to mechanical stress The program J WOOLLENS y Hand Wash is suitable for this type of textile Important Textiles with the care symbol do not wash must not be washed in washing machines 15 Operating Instructions Detergents and care agents Which detergent and care agent Use only detergents and care agents which are suitable for use in wash ing machines Always follow the manufacturer s instructions How much detergent and care agent The required quantity depends upon extent of soiling of the washing on the hardness class of the mains water e the amount of washing If the detergent manufacturer does not give any metering quantities for small loads add a third less for half a load or only half the amount of detergent for small loads for 1 EASY IRON which is recommen ded for a full load Observe the instructions for use and dosing provided by the detergent and conditioner manufacturer Water softener For medium to high water hardness hardness class upwards you should use softener Refer to the manufacturer s instructions Then al ways add the appropriate amount of detergent for hardness class soft The responisable water works will provide information on the local water hardness Since the water softener is rinsed in before the main detergent water pre softening 80 of the stated quantity of softener shown on
43. se hold means The washing remains lying in the last rinsing water It is not spun D SPIN Pumping off the water after a rinse hold and spin or separate spin of hand washed cottons linen F SHORT SPIN Pumping off the water after a rinse hold and gentle spin or separate gentle spin of sensitive textiles easy cares delicates wool 11 Operating Instructions I Additional program buttons The additional program buttons are for adapting the TT washing program to the dirtiness of the washing Addi W tional programs are not required for washing which is not excessively dirty ty Various functions can be combined with each other de pending on the program gt 10 C UU PRE WASH Warm pre wash prior to the main wash that follows on fp O automatically including intermediate spin for ky COTTONS LINEN and key EASY CARES exclud ing intermediate spin for Y DELICATES If J RINSE HOLD has been selected no spinning will take place at all ty SOAKING Approx 50 minutes at 30 C water temperature can be extended to max 10 hours and approx 20 minutes with button DELAY TIMER This is followed by the main washing cycle gt QUICK WASH Short and main washing cycle for slightly dirty washing ds STAIN For treating very dirty washing or stained washing In wash stain treat ment is added during the program on a time optimized basis May only be used for wash temperatures from
44. structions Before the first wash t Perform a washing cycle without washing Program uJ COTTONS LINEN 95 with half the amount of detergent This removes residues left over from production on the drum and solu tion container Prepare washing cycle Sort washing and prepare e Sort the washing according to the care symbol and type see Wash ing types and care codes Empty all pockets Remove metal objects paper clips safety pins etc To prevent damage to the washing and tangled washing Close zip fasteners button bed and pillow covers closed tie up loose strings e g of aprons e Turn articles with double layered textiles inside out sleeping bags anoraks etc n the case of knitted coloured textiles and also with wool and tex tiles with jewelry attached turn inside out e Wash small and sensitive items e g baby socks tights and stockings bras etc in a washing net a cushion with a zip fastener or in larger socks Handle curtains with particular care Metal rollers or burred plastic rollers must be removed or tied into a net or bag We cannot accept liability for damage Coloureds and white items must not be washed together in a washing cycle This could discolour white washing or turn it grey There is often excess dye in new coloured items It is best to wash such items separately the first time Mix small and large items This improves the washing effect and the washing is mor
45. t In addition unscrew the inlet hose form the water tap and place it on the floor Empty the drainage hose Warning Switch off the washing machine before performing emer gency drainage and pull out the mains plug Caution The washing solution escaping from the emergency drainage hose may be hot There is a risk of scalding Allow the washing solution to cool down before performing emergency drainage Place a flat collecting vessel in order to collect the washing solution which is draining off of the base outwards and pull it off from its holder drainage hose by turning it anticlock wise and pull it out The washing solution runs out Depend ing on the amount of solution it may be necessary to empty the collecting vessel several times To do this close the emergency drainage hose temporarily with the plug Operating Instructions When the water is completely drained 6 Push the plug securely into the emergency drainage hose and turn it clockwise to secure it 7 Replace the emergency drainage hose in its holder 8 Put on the flap and close Drain pump The drain pump is maintenance free The cover of the drain pump must only opened in the event of a malfunction when no more water is be ing pumped out e g if the pump is blocked Before loading the machine please always ensure that there are no for eign objects left in the pockets or in between the items to be washed Paper c
46. t Emer gency Drainage Call Customer Service if the emergency drain hose leaks Clean the detergent drawer and attatch the conditioner insert securely Pay attention to the maxi mum filling quantity see Program tables In the case of easy care textiles select the program EASY IRON Always load the drum as ful as possible with a combina tion of large and small items 33 Operating Instructions 34 Problem Washing not well spun Residual water still vis ible in the drum The fault code EZD ap pears The RINSE display flashes The filling door cannot be opened when the unit is switched on Remnants of detergent are building up in the detergent drawer Possible Cause Drainage hose bent Maximum pump head dis charge height 1 m from the unit s floor is exceeded Solution pump blocked If a siphon is connected Si phon blocked The filling door is locked due to a high water level or a high temperature The o DOOR display is off Power failure All displays have gone off For safety reasons the door remains locked for 4 to 10 minutes Water valve not fully opened Filter in the screw connec tion of the intake hose on the water valve or on the unit is blocked Remedy Remove the bend Contact your customer serv ice For pumping heights over Im he can offer you a conversion kit as a special accessory Switch off the unit and pull out the mains
47. ta pe Ba posee PEUT Ee PR 10 Prograim selector eoe SPAS CREE DURER e eda 10 Additional program buttons a e eee eaaa eee 12 Consumption values_ eaaa eaaa aaa aee 13 What does UPDATE mean aee ea eee 13 Before the first wash sara daa seh aa KN eens 14 Prepare washing Cycle ooo 14 Sort washing and prepare_ cece eet aaa aaa 14 Washing Types and Care Symbols a aee eaaa aaa 15 Detergents and care agents a eee eee 16 Which detergent and care agent eee eee ee eee 16 How much detergent and care agent eee eee eee 16 Water SOFTEE vios Sad ceux n e Gud E t Wed Re taal kn PRU RR eee 16 Run a washing cycle ssssseeeeeeeeeee tees 17 Brief instructions 17 Setting the Washing Program eect eaaa re 18 Changing the spin speed Selecting the rinse hold function 19 Set the delay timer soaking duration_ eee 20 Opening and closing the filling door eee eee 21 Add the washing secco IERI ru RS E Eh E Eee 21 Add detergent care agent_ os dies 22 Start the washing program ssssssseee ea ea aaa ea 23 Completion of the Washing Program eee eee ees 23 Change program iie Rb RR E e da Wed bebe 24 The washing cycle is finished Remove the washing 25 Program tables sai aia aia sa aga p Le aa 26 Washing ecco ope Dy C eb lege ere rope d darts 26 Separate
48. wash cycle As a result the cycle is a very quiet one J RINSE HOLD is therefore especially suitable for washing at night Note The laundry remains lying in the water until you drain or spin see section Ending a wash cycle After 18 hours however it is auto matically drained and pumped 19 Operating Instructions 20 Set the delay timer soaking duration Delay timer The DELAY TIMER button allows the start of a washing program to be postponed for between 1 and maximum 19 hours To do this press the d DELAY TIMER button as 1 often as Bed until the required start delay is eo shown in the multi display for example in the f form teh for the postponement of the program Oo start of 12 hours If Sh is displayed and you press again Gh appears followed by the run time of the set program display in minutes e g 128 No delay timer is set in this state Once the delay timer has been set it will only be activated after press ing the START PAUSE button Soaking duration When the E SOAKING button is pressed you can extend the soaking period with the d DELAY TIMER button maximum 10 hours and ap prox 20 minutes Without delay timer the soaking period is approximately 30 minutes plus a pre wash time of 20 minutes To adjust press the d DELAY TIMER button as often as necessary until the required soaking period is shown in the multi display e g ih 21 hour After app
Download Pdf Manuals
Related Search