AEG 7200 Washer User Manual
Contents
1. If the appliances are built in built under fixed or suspended in such a way that remov ing and replacing them in the place where they are fitted takes more than half an hour the costs that result therefrom will be charged for Connected damage caused by these removal and replacement operations will be the responsibility of the user 49 Guarantee conditions 50 12 13 14 15 If during the guarantee period repairing the same defect repeatedly is not conclusive or if the repair costs are considered disproportionate in agreement with the consumer the defective appliance may be replaced with another appliance of the same value In this event we reserve the right to ask for a financial contribution calculated accord ing to the length of time it has been used A repair under guarantee does not mean that the normal guarantee period will be ex tended nor that a new guarantee period begins We give a twelve month guarantee for repairs limited to the same defect Except in the event where liability is legally imposed this declaration of guarantee terms excludes any compensation for damage outside the appliance for which the con sumer wishes to assert his rights In the event of legally admitted liability compensa tion will not exceed the purchase price paid for the appliance These guarantee terms are only valid for appliances purchased and used in Belgium For exported appliances the user must first make sure2. Too much detergent was probably used Remedy Open the tap Start the programme again Close the water tap Unscrew the hose from the water supply tap take out the filter and rinse it under the kitchen tap Check the supply tap have it repaired if necessary Remove locking devices as described in the Installation and Connection instructions Set the feet as described in the Installation and Connection instructions Operation is not affected Check the condition of the outlet hose and straighten any kinks or folds or clean the detergent solution pump removing any foreign bodies from the pump casing if re quired Follow precisely the manu facturer s instructions on the amount of detergent to use 31 Instructions for use 32 Fault Water runs out from under the machine Fabric softener is not drawn in the condi tioner amp compartment is full of water Clothes are severely crumpled The washing has not been spun as dry as usual Possible Cause The water inlet hose coupling is loose The outlet hose is loose The detergent solution pump cover is not properly closed Clothes are caught in the door The emergency drain hose is not properly fastened or is loose The fabric softener tray in the conditioner compart ment is not correctly posi tioned or is clogged Too much washing has probably been loaded The washing was not able to be distributed e
3. 36 E Easy cares 12 16 25 Easy iron 16 25 32 Eco sl lQes ca 14 Emergency emptying 37 Energy saving 11 25 F Filling quantity 14 25 27 Frost hazard 6 37 G Gentle rinse 12 27 H Handwash 4c tees 12 26 27 In wash stain treatment 10 19 L Lines aa ad ago 11 16 25 27 M Multidisplay 11 22 30 55 0 Opening the door 33 P Pre wash 22442 24 aise Bake 13 19 20 25 Pre wash detergent 10 19 Programme progress indicator 22 Pump out 12 23 24 R Rating plate 10 45 55 Rins hold iE aise eed 12 21 24 Running time 22 S SHOr outer uve tesis 13 20 23 25 SilK zu iv rd at 12 16 SOMO acia SERE EA 19 Soaking agent 10 19 Spill se ste nids 12 18 21 23 Stain 9 13 20 23 25 SAINS osc En Comm C E 35 Starching we rs Pesala PU 12 27 W Warranty 6 30 49 Washing coloured odiar ra Las 15 lightly soiled 2c e 9 sensitive 15 16 Washing detergent 17 Washing powder 19 Water hardness 4 oce ph ene 9 17 pump OUT oem 12 23 24 softener 9 10 17 19 Woollens 12 16 26
4. Release and pull out the plug of the emergency emptying hose by turning it anticlockwise The washing solution drains off De pending on the amount of solution it may be necessary to empty the collect ing vessel several times To do this tem porarily close the emergency emptying hose again with the plug When all the washing solution has drained off 6 Firmly push the plug into the emergency emptying hose and turn it tight clockwise 7 Put the emergency emptying hose back into the holder 8 Insert the flap into the base panel and close Instructions for use Child Safety Feature When the child safety feature is used the filling door can no longer be closed and no more washing programs can be started Setting the Child Safety Feature Use a coin to turn the rotary knob on the inside of the filling door clockwise as far as it will go Warning The rotary knob must not be pressed in following adjust ment otherwise the child safety feature is not active The rotary knob must project as shown in the diagram Cancelling the Child Safety Feature Turn the rotary knob anticlockwise as far as it will go M NS 39 Setting up and connection instructions Setting up and connection instructions Safety Instructions for Installation Do not tilt the washing machine onto its front or onto its right side looking from the front Electrical components could get wet Check the
5. 27 hand washable 12 26 Service Service In the section What to do if there is a list of some faults which you can remedy yourself Look there first if a fault occurs If you find no in formation there please consult your Customer Service Centre Always prepare in advance for the discussion By doing so you will sim plify the diagnosis and the decision on whether customer service is necessary Note the PNC number and the S number Both can be found on the rating plate on the inside of the door on your washing machine PNG sunto ect S NO AR ee te Answer as precisely as possible e What form does the fault take e Under what circumstances does the fault occur Does the multi display show an error message AEG LAVAMAT XYZ 5 No000 000000 When do you incur costs even during the warranty period if you could have dealt with the fault yourself with the aid of the Faults Table see the section What to do if if several trips by the customer service technician are necessary be cause he had not received all the necessary information before his visit and must now e g fetch spare parts These multiple trips can be avoided if you prepare your phone call as described above 55 E From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and ou
6. Dee go dis 18 Add Washing Detergent Care Agent 19 Set the Washing Program 20 Change Spin Speed Select Rinse Hold 21 Starting the programme 22 Programme display 4 saved cid me sw dra mets 22 Changing the programme 23 End of wash cycle Taking out washing 24 Programme charts 25 Washi rem en aan ve ERY ERA Xo nO EC Det IC Edd d darts 25 Separate Conditioning Starching Impregnating 27 Separate FINSE sone LE Le LL uns 27 Separate SPIN meriiri rier ranan eee wary Adee EDD HUI E eA tr 27 Cleaning and Care a is 28 Control Panel sise tante tenia a is wae aia 28 Washing Detergent Drawer 28 Washing Drum uere tenerne dade paddies te de oa lan 29 Alling Door ine pee ret ede da 29 What to dosis cin he eats E t E ep VP ET 30 Remedying Faults cde six redde ed ee e Gee 30 If the washing result is not satisfactory 35 MEILEN 36 Carry Out an Emergency Emptying Operation 37 Child Safety Feature 39 Setting up and connection instructions 40 Safety Instructions for Installation 40 Settin
7. Rating plate behind filling door Filling door Flap in front of drain pump Pre wash detergent soaking agent or water softener Liquid care agent conditioner finisher starch Instructions for use Control panel Spin speed RINSE HOLD button START PAUSE button Programme selector mel mo nE O O 900 O 700 cSuRt v IGEEN CENTR ISANS ESSOR LOOPTUD TEMPS RESTANT HOOFDWAS STAND LAVAGE POMPEN gr SPOELEN VIDANGE ECO RINCAGE STUVEN CENTRIFUG y AMIDON ESSORAGE FUN SPOELEN EINDE RINC DELICAT FIN 60 KREUKHER S KOUD S FROID tate o 40 T o 50 DEFROISSABLE 30 40 40 40 FIJNE WAS XN STRIJKVRIJ LINGE DELICAT J SANS REPASSAGE KORT CENTRIFUG UIT TE NE US PRELAVAGE CENTRIFUG RUD AN o 195 Multidisplay Additional programme buttons Programme selector The programme selector is used to choose the most suitable wash setting for example wa ter level type of drum move ment number of rinses spin speed forthe type of wash as well as the temperature of the detergent solution OFF UIT ARRET e Switches off the machine at all other positions the machine remains on Progress indicator KORT CENTRIFUG UIT ESSOR DELICAT ARRET CENTRIFUG ESSORAGE DO O POMPEN VIDANGE C STIJVEN AMIDON FIJN SPOELEN RINC DELICAT KOUD SY FROID WOL 30 WITTE BONTE WAS BLANC
8. The intake and drainage hoses must not be bent or pinched Setting Up on a Concrete Pedestal When setting up the washing machine on a concrete pedestal it is essential for safety reasons to fit stand plates in which the washing machine is then adjusted The stand plates are available from the Customer Service under spare part number 645 425 058 O Setting Up on a Vibrating floor In the case of vibrating floors especially wooden beam floors with flex ible boards securely screw a water resistant wooden panel at least 15mm thick onto at least 2 of the floor beams If possible set up the unit in a corner of the room where the wooden floor is best firmly in stalled and is therefore least likely to be susceptible to vibrations 43 Setting up and connection instructions Compensate for Floor Unevenness Floor unevenness can be compensated for and the height can be cor rected with the four adjustable screw feet The height can be adjusted in a range of 10 5 mm To adjust the feet use the special spanner supplied for removing the transport braces Eg 1 Slide the special key firmly onto the hexagon head of the threaded foot as far as it will go 2 Adjust the screw feet so that the unit is horizontal and stable The unit must not wobble over when loaded 3 If necessary check the setting with a spirit level Attention Never compensate for
9. not place the washing machine on its front side or on its right side looking from the front Otherwise the electrical components can get wet e Never transport the unit without using the transport safeguard Do not remove the transport safeguard until you reach the installation site Transporting the unit without the transport safeguard can result in damage to the unit e Never lift the unit by the open filling door or by its base When transporting the unit with a sack trolley Attach the sack trol ley only at the side Remove the Transport Safeguard Attention It is essential to re TT move the transport safeguard be g fore putting the unit into S operation Keep all parts of the transport safeguard in a safe place for possible later transport moving house t 1 Open both hose holders on the rear of the unit and remove the hoses and the mains cable K W ONO 2 Firmly pull both hose holders off the unit 41 Setting up and connection instructions 42 N The special button A and the plug caps B 2 ea and C 1 ea are supplied with the unit Remove the screw D including the compression spring with the special button A Close off the hole with the plug cap C Attention Push in the plug cap so firmly that it engages in the rear panel this protects the inside of the unit against splash water Unscrew the two screws E using the
10. the required spin speed or of RINSE HOLD GEEN CENTR SANS ESSOR lights up If RINSE HOLD GEEN CENTR SANS ESSOR is selected the washing re mains in the last rinsing water and is not spun If you do not change the spin speed the final spin is automatically adapted depending on the washing program COTTONS LINEN WITTE BONTE WAS BLANC COULEURS EASY CARES EASY IRON KREUKHERSTELLEND STRUKVRI DEFROISSABLE SANS REPASSAGE DELICATES FUNE WAS LINGE DELICAT WOOLLENS WOL LAINE amp Handwash The speed of the intermediate spin depends on the selected program and cannot be changed 1200 revolutions per minute 900 revolutions per minute 700 revolutions per minute 900 revolutions per minute 21 Instructions for use Starting the programme t 1 Check that the water supply tap is open 2 Start the program Press the START PAUSE SUART PAUZE START PAUZE MARCHE PAUSE button MARCHE PAUSE The programme starts Programme display 22 Progress indicator MOORWAS e Before the programme begins the steps to be com HOQIDWAS pleted are shown on the Progress indicator The stage SPOELEN of the programme currently running is indicated CENTRIFUG ESSORAGE vr Multidisplay 1 3 4 LOOPTUD The estimated time remaining in minutes is l RESTANT shown on the Multidisplay until the programme is completed The remaining time may lengthen or shorten as
11. the water after a rinse hold no spin RINSE HOLD GEEN CENTR SANS ESSOR means The washing is left to soak in the last rinse water It is not spun SPIN CENTRIFUG ESSORAGE Pumps out the water after a rinse hold or spin or for separate spinning of hand washed cottons linen GENTLE SPIN KORT CENTRIFUG ESSOR DELICAT Pumps out the water after a Rinse Hold and Gentle Spin or separate gentle spin of delicate textiles easy care clothes delicates woollens Instructions for use Additional Programming Buttons The additional programming buttons adjust the VOORWAS wash cycle according to how soiled the washing is PRELAV O Additional cycles are necessary only if the washing i i i KORT is excessively soiled courr Depending on the cycle chosen the various func tions may be used in combination with each an VLEKKEN other TACHES PRE WASH VOORWAS PRELAV Warm pre wash prior to the main wash cycle main wash cycle follows automatically with spin cycle for COTTONS LINEN WITTE BONTE WAS BLANC COULEURS and EASY CARES KREUKHERSTELLEND DEFROISSABLE without spin cycle for DELICATES FIJNE WAS LINGE DELICAT SHORT KORT COURT Shortened main wash cycle for washing that is lightly soiled STAIN VLEKKEN TACHES For treating washing that is heavily soiled or stained Stain removal agent is rinsed in at an optimal point in the cycle This cycle can only be set for a washing temperature of o
12. washing machine for transport damage Never connect a damaged unit Consult your supplier in the event of damage e Ensure that all parts of the transport safeguard have been removed and that the splash guard is fitted to the unit see Removing the Transport Safeguard Otherwise damage to the unit or to adjacent furniture could occur during spinning Always insert the plug into a correctly installed PE socket n the case of permanent installation A permanent installation may only be made by an authorised specialist Before putting the unit into operation ensure that the rated voltage and current type shown on the unit s rating plate are the same as the mains voltage and current type at the installation location The re quired electrical fuse is also shown on the rating plate e Should work be carried out on the water supply installations in order to allow the machine to be connected properly to the water supply this work must be carried out by an authorised installer e Should work be carried out on the mains supply in order to allow the machine to be connected properly to the electricity supply this work must be carried out by an authorised electrician he mains cable may only be replaced by the Customer Service or by an authorised specialist Setting up and connection instructions Setting Up the Unit i Washing machines with curved panels are not suitable for substruc tures Transporting the Unit Do
13. weight 5kg 2 5kg 2 5kg 2kg Max load size dry weight 5kg 2 5kg 2 5kg 2kg Programme selector STARCHING STUVEN AMIDON Programme selector GENTLE RINSE FIJN SPOELEN RINC DELICAT Programme selector SPIN CENTRIFUG ESSORAGE SHORT SPIN KORT CENTRIFUG ESSOR DELICAT 27 Instructions for use 28 Cleaning and Care Control Panel pe Attention For cleaning panels and control parts do not use furniture polish or any aggressive cleaning agents Wipe off control panels with a damp cloth Use warm water to do this Washing Detergent Drawer I 1 2 Clean the softener insert under The washing detergent drawer should be cleaned from time to time Pull out the washing detergent drawer as far as it will go Remove the washing detergent drawer with a firm pull Remove the softener insert from the middle compartment running water Clean the compartments from the rear with warm water It is best to use a bottle brush Push on the softener insert as far as it will go so that it is secure Instructions for use 7 Use a brush to clean the entire rinsing in part of the washing ma chine especially the nozzles on the top side of the rinsing in chamber 8 Insert the washing detergent drawer into the guide rails and push it in Washing Drum The washing drum is made of high quality stainless steel Rust deposits on the drum can occ
14. COULEURS 60 KREUKHER 5o ne STELLEND DEFROISSABLE 30 40 40 40 FIJNE WAS STRIJKVRIJ LINGE DELICAT SANS REPASSAGE e Clears programme settings selected by mistake The original settings are restored COTTONS LINEN WITTE BONTE WAS BLANC COULEURS Main wash for cottons linen at 30 C to 95 C Position ENERGY SAVING ENERGIEBESP ECONOMIQUE Energy sav ing programme at around 67 C for slightly or normally soiled cottons extended wash time cannot be combined with the SHORT KORT COURT setting Instructions for use EASY CARES KREUKHERSTELLEND DEFROISSABLE Main wash for easy care textiles blend fabrics at 40 C to 60 C Position EASY IRON STRISKVRIJ SANS REPASSAGE Main wash at 40 C for easy care textiles which require only lightor no ironing with this setting DELICATES FIJNE WAS LINGE DELICAT Main wash for delicates at 30 C or 40 C WOOL WOL LAINE amp Handwash Main wash up to 40 C for both machine washable and hand washable woolens and silk with the Care symbol handwash GENTLE RINSE FIJN SPOELEN RINC DELICAT Separate gentle rinse for example for handwash textiles 2 rinses liquid conditioner washed in amp from the drawer gentle spin STARCHING STIJVEN AMIDON Separate starch separate gentle rinse separate conditioning for wet clothes 1 rinse liquid conditioner washed in from amp 3 drawer spin PUMP OUT POMPEN VIDANGE Empties
15. LAVAMAT 7200 ELECTRONIC Washing Machine User Information Dear customer Please read this user information carefully In particular pay attention to the section Safety on the first pages Keep this user information in a safe place for later reference Pass it on to any subsequent owners of the unit Points which are necessary for your safety or which are important for the unit s functional capability are highlighted by a warning triangle and or signal words Warning Caution Attention Always remem ber his symbol guides you step by step in operating the unit After this symbol you will find detailed information on operation and practical use of the unit The clover leaf indicates tips and information on the economical and environmentally responsible use of the unit This user information contains information on remedying any faults which may occur see the section What to do if If these instructions are not sufficient our After Sales Service is at your disposal at any time ELGROEP amp AEG SERVICE Bergensesteenweg 719 1502 Lembeek Tel 02 3630444 Here you will receive an answer to any question concerning the fea tures and use of your unit Of course we are also pleased to receive any requests suggestions and criticism Our aim is to further improve our products and services for the benefit of our customers In the event of technical problems our factory customer service
16. SH VOORWAS PRELAV SHORT KORT COURT STAIN VLEKKEN TACHES PRE WASH VOORWAS PRELAV SHORT KORT COURT STAIN VLEKKEN TACHES 25 Instructions for use Type of items to be washed Care label Delicates Woollens Hand wash 6 va W Max load size dry weight 2 5kg or 15 20m curtains 2kg Programme selector Temperature DELICATES FUNE WAS LINGE DELI CAT 30 40 amp WOOL WOL LAINE COLD KOUD FROID to 40 Additional programmes possible PRE WASH VOORWAS PRELAV SHORT KORT COURT STAIN VLEKKEN TACHES 1 The load amount inquiry operates in accordance with the EN 60456 standard load 2 One 10 litre bucket contains around 2 5 kg of dry washing cotton 3 If STAIN represent a temperature of at least 40 C is required to enable the stain remover agent to work efficiently 4 Creases in the washing can be avoided to a large extent only if the load size is kept under 1 kg 5 to 7 easy care men s shirts are equal to around 1 kg of dry washing 26 Instructions for use Separate Conditioning Starching Impregnating Type of items to be washed Cottons Linen Separate rinse Type of items to be washed Cottons Linen Easy Cares Delicates Woollens Handwash Separate spin Type of items to be washed Cottons Linen Easy Cares Delicates Woollens Handwash Max load size dry weight 5kg Max load size dry
17. The plug is not in the socket Insert the plug The fuse or protection device icr udo Replace reset the fuse The machine does not The machine door was not Close the door You should work closed properly hear the door engage The START PAUSE START Press the START PAUSE PAUZE MARCHE PAUSE START PAUZE MARCHE button was not pressed long PAUSE until the Programme enough begins Release the child safety de The child safety device has vice pss tee de The door will not close been set Met vice Error code EMG ap pears The MAIN WASH The door is not closed Close the door properly HOOFDWAS LAVAGE properly Start the programme again indicator flashes Instructions for use Fault The water does not flow Error code E iD ap pears The SPIN CEN TRIFUG ESSORAGE indicator flashes The washing machine is noisy or vibrates in use The detergent solution in the main wash foams excessively Possible Cause The water supply tap is closed The filter in the water inlet hose coupling is clogged The water supply tap is blocked with limescale or is faulty The locking devices were not removed The adjustable feet are not set to the correct height There are very few items of washing for example one dressing gown in the drum The water could not be pumped out completely be fore spinning as there is a kink in the outlet hose or detergent solution pump is clogged
18. additonal program PRE WASH VOORWAS PRELAVAGE or for water softener If using Liquid Detergent Tabs Add liquid detergent tabs in the amount recommended by the washing detergent industry Follow the instructions on the detergent package 19 Instructions for use Set the Washing Program T I 1 20 For a suitable program the right temperature and possible additional programs for the relevant washing type refer to the Program Tables Set the program selector to ENANOS akker WITTE BONTE WAS the required washing program Be o with the required temperature POMPEN The probable duration of the AMIDON F FIJN SPOELEN set program in minutes Is RINC DELICAT shown in the multi display Sy Kob A WOL 30 e 60 KREUKHER LAINE STELLEND 50 DEFROISSABLE 30 40 40 40 FIJNE WAS STRIJKVRIJ LINGE DELICAT SANS REPASSAGE Select any additional programs VEGAS The indicator for the selected additional program PRELAV O lights up Press another button to make different selection coor e Press the button again to deselect VLEKKEN TACHES Instructions for use Change Spin Speed Select Rinse Hold pe If necessary change the spin speed for the final spin select RINSE HOLD GEEN CENTR SANS ES n SOR n 700 O Press the button Spin speed RINSE HOLD GEEN CENTR SANS ESSOR as often as necessary until SANS Essar O the display for
19. ater pressure 1 10bar 210 100 N cm 0 1 1 0 MPa Dimensions 10 8507 Measurements in mm 48 Guarantee conditions Guarantee conditions 10 11 Belgium DECLARATION OF GUARANTEE TERMS Our appliances are produced with the greatest of care However a defect may still oc cur Our consumer services department will repair this upon request either during or after the guarantee period The service life of the appliance will not however be re duced as a result This declaration of guarantee terms is based on European Union Directive 99 44 EC and the provisions of the Civil Code The statutory rights that the consumer has under this legislation are not affected by this declaration of guarantee terms This declaration does not affect the vendor s statutory warranty to the end user The appliance is guaranteed within the context of and in adherence with the following terms In accordance with provisions laid down in paragraphs 2 to 15 we will remedy free of charge any defect that occurs within 24 months from the date the appliance is deliv ered to the first end user These guarantee terms do not apply in the event of use for professional or equivalent purposes Performing the guarantee means that the appliance is returned to the condition it was in before the defect occurred Defective parts are replaced or repaired Parts replaced free of charge become our propert
20. ation see Carry ing out an emergency drain operation After about 2 minutes the door can be opened by pull ing the handle Open the supply tap fully Close the water supply tap Disconnect the inlet hose from the tap and from the appliance Clean the filter There are no adverse effects on rinse results if preferred use a liquid detergent Select another function Instructions for use If the washing result is not satisfactory If the washing is grey and limescale forms in the drum Not enough washing detergent added e The right washing detergent was not used e Special types of stain were not pretreated Program or temperature incorrectly set e f binary wahing detergents were used the individual components were not added in the correct ratio If there are still grey stains on the washing Washing contaminated with creams grease or oils was washing with too little detergent Washing at too low temperature A frequent cause is that conditioner particularly concentrated form ended up on the washing Wash out such stains as quickly as possible and carefully use the right conditioner If foam is still visible after the final rinse Modern washing detergents can still produce foam even in the final rinse The washing is still sufficiently rinsed If there are white residues on the washing These are the insoluble components of modern detergents They are not the result of an insuffi
21. ay be used for extension purposes max 3m on the floor and then up to 80cm high The Customer Service stocks hoses in lengths of 2 7 and 4m Attention It is absolutely essential to install the drainage hose free of pinches Water Drainage into a Siphon The grommet on the end of the hose fits all commonly used siphon types Co r Secure the grommet siphon connecting gt g point with a hose clamp e Draining the water into a basin Attention Small basins are not suitable for draining the water into them Water could overflow It is not permitted to submerge the end of the drainage hose into the pumped off water Water could be sucked up into the hose When hooked into a wash basin or a bath tub the drainage hose must be protected from slipping out of place by the supplied slip on elbow Other wise the repelling power of the drain ing water can press the hose out of the sink ts Fix the elbow to the water tap or to the wall with string 47 Setting up and connection instructions Delivery Heads over 1m To pump off the washing rinsing agent every washing machine has a pump which transports liquids via the drainage hose up to a height of 1m calculated from the machine s floor For delivery heads over 1m consult the Customer Service Technical Data Height adjustment Approx 10 5mm Filling quantity max 5kg program dependent Use Domestic Drum speed spin see rating plate W
22. cient rinsing effect Shake or brush off the washing Perhaps in future you should turn the washing before washing it Check the choice of detergent and use a liquid detergent if necessary 35 Instructions for use 36 Drain pump al Unscrew the drain pump cover in an Remove any foreign objects and fabric Check that you are able to turn the The drain pump is maintainance free The cover of the drain pump is required to be opened only in the event of a malfunction when no more water is being pumped out e g if the pump wheel is blocked Before loading the machine please always ensure that there are no for eign objects present in the pockets or inbetween the items to be washed Paper clips nails etc which may find their way into the wash ing machine along with the washing will remain in the drain pump housing foreign objects are protected by the pump wheel To restart the drain pump when it is blocked please proceed as follows Warning Switch off the washing machine and remove the mains plug before cleaning the drain pump First carry out an emergency emptying procedure see section Carrying out emergency emptying Place a cloth on the floor in front of the cover of the drain pump Residual water may run out anti clockwise motion and pull it out lint from the pump housing and from the pump wheel pump wheel at the very rear of the pump housing If the wheel rotat
23. d while the programme is running Press the START PAUSE START PAUZE MARCHE PAUSE button Change the spin speed with the Spin speed RINSE HOLD GEEN CENTR SANS ESSOR button Press the START PAUSE START PAUZE MARCHE PAUSE button again The programme continues 23 Instructions for use 24 End of wash cycle Taking out washing I 1 N occ When the programme is completed the END EINDE FIN light on the progress indicator comes on If RINSE HOLD GEEN CENTR SANS ESSOR was selected the indicator beside the START PAUSE START PAUZE MARCHE PAUSE button flashes After a Rinse Hold the water must be pumped out first Press either the START PAUSE START PAUZE MARCHE PAUSE button the water is pumped out and the spin cycle starts depending on the programme pressing the START PAUSE START PAUZE MARCHE PAUSE button again allows you to change the spin speed even while spinning is in progress or turn the programme selector to OFF UIT ARRET then to PUMP OUT POMPEN VIDANGE and press the START PAUSE START PAUZE MARCHE PAUSE button the water is pumped out without spin ning or turn the programme selector to OFF UIT ARRET then to SPIN CEN TRIFUG ESSORAGE or GENTLE SPIN KORT CENTRIFUG ESSOR DELI CAT then press the START PAUSE START PAUZE MARCHE PAUSE button the water is pumped out and the Spin or Gentle Spin cycle starts When this progra
24. es with a jerky motion this is normal If you cannot turn the pump wheel please contact customer service Instructions for use 6 Replace the pump cover Laterally insert the webs on the cover into the guide slots and securely screw on the cover in a clockwise motion 7 Close the emergency emptying hose and place it in the holder 8 Close the flap Carry Out an Emergency Emptying Operation When the washing machine no longer pumps off the washing solu tion an emergency emptying operation must be carried out e When the washing machine is in a room where there is a frost risk an emergency emptying operation must be carried out when there is a frost risk Also Unscrew the intake hose from the water tap and lay it on the floor Empty the drainage hose A Warning Switch off the washing machine before carrying out an emergency emptying operation and pull out the mains plug Caution The washing solution running out of the emergency emptying hose can be hot Risk of scalding Allow the washing solution to cool down before carrying out emergency emptying t 1 Provide a flat collecting vessel to catch the washing solution as it runs out 2 Open the flap downwards in the right part of the base panel and pull it off 3 Remove the emergency emptying hose from the holder 37 Instructions for use 38 4 Place the collecting vessel underneath 5
25. g Up the Unit 41 Transporting the Unit 41 Remove the Transport Safeguard 41 Prepare the Installation Location 43 Setting Up on a Concrete Pedestal 43 Setting Up on a Vibrating floor 43 Compensate for Floor Unevenness 44 Electrical Connection 45 Water Connection 45 Permissible Water Pressure 45 Watei2Inflow 25 ieu Ce eor et RIO PEL 46 Water Drainage iiis see eta erc he Y e e m d des 47 Delivery Heads over 1m 48 Technical Data oi ia 48 DIMENSIONS gt LIRE A Ue mettersi NUS ir ee m 48 Guarantee conditions 49 Customer services 1 51 Ide x oo sores a e a E cobre Sex Reed 54 Instructions for use Instructions for use N Safety The safety of AEG electrical appliances conforms to the recognised technical regulations and the legislation covering the safety of appli ances However as manufacturers we still regard it as our responsibility to inform you of the following safety information Before Putting into Operation for the Fi
26. g up and connection instructions 46 Water Inflow Connect the hose with the angled connection to A pressure hose 1 5m in length is supplied If a longer inflow hose is required only a VDE approved complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible Sets of hoses in lengths of 2 2 m 3 5m and 5m are available for washing machines without Aqua Control Sets of hoses in lengths of 2 0m 2 9 m and 3 9 m are available for washing machines with Aqua Control Attention Never cut into pieces in order to extend the hoses Sealing rings are supplied either in the plastic nuts of the hose screw connection or in the en closed pack Do not use other seals the machine Attention Do not lay the supply hose vertically downwards Rather turn it to the right or left as shown in the diagram Only tighten the screw connection manually Connect the hose with the straight connection to a water tap with a screw thread of R 3 4 inches x Attention Only tighten the screw connection 3 manually E SF By slowly opening the water tap before putting 3 the washing machine into operation check whether the connection is free of leaks Setting up and connection instructions Water Drainage The drainage hose can either be connected to a siphon or hung ina wash basin or bath tub Only original hoses m
27. he Program Tables For information on the correct preparation of the washing see Sort and Prepare the Washing Sort and prepare the washing according to type 2 3 Open the filling door Pull on the handle of the filling door Fill with washing Attention When closing the door make sure no items of washing get stuck This could damage textiles and the unit Instructions for use Add Washing Detergent Care Agent t 1 Open the washing detergent drawer Fill with washing detergent Push the drawer fully in Refer to the information on washing detergents and care agents see section Washing Detergents and Care Agents grip inside the flap on the drawer at the bottom 1 and pull out the drawer as far as it will go 2 care agent Compartment for in wash stain L treatment Compartment for main washing powder If you use water softener and need the right compartment for the pre wash agent add the water softener to the main washing detergent in the left compartment Compartment for liquid care agent Conditioner finisher starch Attention Fill the compartment up to the MAX mark If necessary dilute viscous agent up to the MAX mark and dissolve powder starch Note It is normal for a small amount of water to be left in the compartment for liquid conditioner this will not affect the wash results Compartment for pre wash agent only for
28. in your area is at your disposal at all times Also refer to the section Service Printed on recycled paper Those who think ecologically act ecologically Contents Instructions for ASG 4 2505 O 6 SE LEO ARS r eE aa A aa Ar E a A a A aa Aaa 6 Disposal 2 se SEU s 8 Environment Tips 9 Unit Description 22344844 iia ws dut bn bee bebe a nes 10 Front VIEW vinrent e rait cape t PRG ol RO P bod a tar EI Ead 10 Drawer for Washing Powder and Care Agent 10 Control panel otura DR Oe I PRpEObUE E e PER 11 Programme selector 11 Additional Programming Buttons 13 Consumption Values 14 Before the First Wash 14 Prepare the Washing Cycle 15 Sort and Prepare the Washing 15 Washing Types and Care Codes 16 Washing Detergents and Care Agents 17 Which washing detergent and care agent 17 How much washing detergent and care agent 17 Water Softener ics die eee eret bt data da ue e Rerum a des 17 Performing a wash cycle 18 QuickStart GUJE 3 citer SERIE DEED ae eI RM 18 Add the Washing cc ce et P
29. itch off the appliance and pull out the mains plug Clean the syphon Wait till the programme has finished and the END EINDE FIN indicator light is on However if you still need to open the door Set the programme selector to OFF UIT ARRET Turn the programme selector to PUMP OUT POMPEN VIDANGE Press the START PAUSE START PAUZE MARCHE PAUSE button When the water has been pumped out the door can be opened 33 Instructions for use 34 Fault Mains power failure while a programme is running all indicators are off Leftover detergent builds up in the deter gent dispenser drawer The rinse water is not clear When one of the addi tional programme function buttons is pressed the corre sponding indicator light does not come on Possible Cause Power may have been cut off by the electricity supplier the door remains locked for around 2 minutes for safety reasons The water supply tap is not fully open The filter in the water inlet hose coupling at the tap or at the appliance is clogged The cause may be that the detergent is high in silicates The additional programme function selected cannot be combined with the programme already set Remedy The programme will con tinue when power Is re stored If the washing has to be taken out during the power failure Turn the programme selec tor to OFF UIT ARRET Carry out an emergency drain oper
30. ld Safety e Packaging components e g films polystyrene can be hazardous to children Risk of suffocation Keep packaging away from children Children often cannot recognise the hazards associated with handling electrical appliances Therefore ensure the necessary supervision dur ing operation and do not allow children to play with the washing ma chine there is a risk that children can get trapped inside Ensure that children or small animals cannot climb into the washing machine s drum When disposing of the washing machine Pull out the mains plug de stroy the door lock cut off the electrical supply lead and throw away the plug and the left over cable This means that children at play cannot shut themselves inside and in so doing be in danger General Safety Repairs to the washing machine may only be carried out by qualified specialists Incorrect repairs may result in significant risk to the user If repairs are necessary consult our customer service or your special ist dealer Never use the washing machine if the mains cable is damaged or the conrol panel work surface or base panel area are so badly damaged that the interior of the unit is openly accessible Switch off the washing machine before carrying out cleaning care and maintenance work Also pull the mains plug out of the socket or if it is permanently connected switch off the circuit breaker at the household power distribution box or complete
31. ly remove the screw in fuse e f operation is stopped disconnect the appliance from the mains sup ply and shut off the tap Never pull the cable to remove the plug from the socket Always pull the plug itself Multiple connectors couplings and extension cables must not be used There is a risk of fire with overheating Do not spray down the washing machine with a water jet Risk of electric shock The glass in the door becomes hot in the case of wash programmes with high temperatures Do not touch Instructions for use Allow the washing solution to cool before carrying out an emergency emptying operation or cleaning the drain pump Small animals can chew the power cables and water hoses Risk of electric shock and danger of water damage Keep small animals away from the washing machine e Disposal Dispose the packing material Dispose of your washing machine s packaging correctly All the packag ing materials used are harmless to the environment and can be recy cled Plastic parts are marked with standard international abbreviations gt PE lt for polyethylene e g sheet wrapping material gt PS lt for polystyrene e g padding material always CFC free gt POM lt for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Dispose the old appliance When you finally put your appliance o
32. minor floor unevenness with un derlays made of wood card etc Always adjust the adjustable feet 44 Setting up and connection instructions Electrical Connection Refer to the rating plate for details of the mains voltage current type and the necessary fuses The rating plate is located at the top behind the filling door C This unit conforms to the following EU directives the Low Voltage Directive 73 23 EU with changes the EMC Directive 89 336 EWG with changes Water Connection i The washing machine has safety features which prevent contamination of the drinking water and which conform to the legal regulations of the water authorities e g for Germany DVGW regulations Other pro tection measures in the installation are therefore not necessary Attention Units for connection to cold water must not be connected to hot wa ter Use only new sets of hoses for connection Permissible Water Pressure The water pressure must be at least 1bar 10N cm 0 1 MPa maxi mum 10bar 100N cm 1 MPa In the case of more than 10bar Connect a pressure reducing valve upstream e n the case of less than 1bar Unscrew the intake hose on the unit side on the inlet solenoid valve and remove the flow regulator to do this remove the filter with pointed pliers and remove the rubber washer behind Replace the filter 45 Settin
33. mme stage is ended the END EINDE FIN indicator light comes on Open the door The door can be opened when the END EINDE FIN light comes on Take out the washing Turn the programme selector to OFF UIT ARRET Close the water supply tap When washing is complete pull the detergent dispenser drawer out to let it dry Leave the door open for a while to air the inside of the machine Attention If the washing machine is not used for a long time Close the water tap and disconnect the washing machine from the electricity mains Instructions for use Programme charts Wash All settings that are generally used in every day operation of the ma chine but not all possible settings are listed here Type of items to be washed Care label Cottons Energy Saving programme Cottons Linen Easy Cares Max load size dry weight 5kg 5kg 5kg 2 5kg 1kg Programme selector Temperature COTTONS LINEN WITTE BONTE WAS BLANC COULEURS 95 COTTONS LINEN WITTE BONTE WAS BLANC COULEURS ENERGY SAVING ENERGIEBESP ECONOMIQUE COTTONS LINEN WITTE BONTE WAS BLANC COULEURS 30 to 60 EASY CARES KREUKHERSTELLEND DEFROISSABLE 30 to 60 EASY IRON4 STRUKVRU SANS REPASSAGE 40 Additional programmes possible PRE WASH VOORWAS PRELAV SHORT KORT COURT STAIN VLEKKEN TACHES PRE WASH VOORWAS PRELAV STAIN VLEKKEN TACHES PRE WA
34. ontainer and the eco sluice can function correctly 3 Run the washing cycle without washing COTTONS WITTE WAS BLANC 95 C with half the amount of washing detergent This removes resi dues left over from production on the drum and solution container Instructions for use Prepare the Washing Cycle Sort and Prepare the Washing Sort the washing according to care codes and type see Washing Types and Care Codes Empty pockets e Remove metal parts paper clips safety pins etc To prevent washing damage and washing snags Close zip fasteners button closed bed covers and pillow cases and tie together ribbons e g on aprons Use clothing made of double layer fabric sleeping bag anorak etc On knitted coloured textiles and on wool and textiles with fitted decorations Turn inside out e Wash small and sensitive items baby socks stockings tights bras etc in a washing net a cushion with a zip fastener or in larger socks Treat curtains with particular care Remove small metal rollers or small burred rollers or tie them in a net or in a bag We cannot ac cept any liability for damage Do not wash coloureds and whites together in one washing cycle Otherwise whites will discolour or turn grey New coloureds often contain surplus dye It is best to wash such items separately the first time Mix small and large items of washing This speeds up theeffect of washing and the washing is more favou
35. rably distributed during spin ning Loosen up the washing before loading it into the washing machine Put the washing into the drum folded out e Pay attention to the care instructions Wash separately and Wash separately several times 15 Instructions for use Washing Types and Care Codes The care codes help you choose the correct washing program The washing should be sorted according to type and care code The temper atures stated in the care codes are all maximum values Cottons Textiles made of cotton and linen with this care code are insensitive to mechanical stress and high temperatures The program COTTONS LINEN WITTE BONTE WAS BLANC COULEURS is suitable for this type of washing Linen Textiles made of cotton and linen with this care code are insensitive to mechanical stresses The program COTTONS LINEN WITTE BONTE WAS BLANC COULEURS is suitable for this type of washing Easy Care Garments Textiles such as finished cottons cotton mixtures viscose and synthet ics with this care code require mechanically more mild treatment The program EASY CARES EASY IRON KREUKHERSTELLEND DEFROISSA BLE STRUKVRIJ SANS REPASSAGE is suitable for this type of washing Delicates Textiles such as layered fibres microfibres viscose synthetics and cur tains with this care code require very gentle treatment The program DELICATES FIJNE WAS LINGE DELICAT is suitable for this type of washing Wool and Ve
36. rst Time Refer to the Installation and Connection Instructions later in this user information e When the unit is delivered in winter months with minus tempera tures Store the washing machine for 24 hours at room temperature before putting it into operation Correct Use e The washing machine is only designed for normal domestic washing If the unit is used for purposes other than that for which it is de signed the manufacturer can accept no liability for any resulting damages For safety reasons conversions or modifications to the washing ma chine are not permissible Use only detergents which are suitable for washing machines Follow the washing detergent manufacturer s instructions e The washing must not contain any flammable solvents Also remem ber this when washing pre cleaned washing Do not use the washing machine for chemical cleaning Dyes dye removers may only be used in washing machines if the manufacturer expressly allows these products We cannot be held lia ble for any resulting damage Use only water from the water mains Use rainwater or service water only if it meets the requirements outlined in DIN 1986 and DIN 1988 e Frost damage is not covered by the warranty If the washing machine is in a room which is at risk from frost an emergency emptying oper ation must be carried out when there is a frost risk see the section Carry Out Emergency Emptying Instructions for use Chi
37. ry Sensitive Washing i Textiles such as wool wool mixtures and silk with this care code are es pecially sensitive to mechanical stresses The program WOOLLENS WOL LAINE amp y handwash is suitable for this type of textiles Attention Textiles with the care code Yz Do not wash must not be washed in the washing machine Instructions for use Washing Detergents and Care Agents Which washing detergent and care agent Use only washing detergents and care agents which are suitable for use in washing machines Always follow the manufacturer s instructions How much washing detergent and care agent The amount to be used depends on e the dirtiness of the washing e the hardness category of the mains water supply e the filling quantity If the detergent manufacturer gives no details of the dosing quantities for minimum loads add one third less for half loads and in the case of very small loads and for EASY IRON STRUKVRIJ SANS REPASSAGE only half the amount of detergent recommended for a full load Refer to the detergent care agent manufacturer s instructions on use and dosage Water Softener For medium to high water hardness hardness category II or higher you should use water softener Pay attention to the manufacturer s instruc tions Always then meter detergent for hardness category soft The responsible water works can provide information on the local water hardness Since the water softener i
38. s added before the main washing detergent water pre softening eighty percent of the softener quantity stated on the package is sufficient Water Hardness Details Wiater neriness h Water Hardness in mmol l Hardness Category o e atili par Hra soft 0 7 up to 1 3 Il medium hard 7 14 135203 Ill hard 14 21 2 5 3 8 IV very hard over 21 over 3 8 17 Instructions for use Performing a wash cycle Quick Start Guide c 1 2 Pour detergent conditioner into the drawer Choose a suitable programme To complete a wash cycle follow the steps below Open the door load the washing Close the door use the programme selector to set the programme set any additional programme functions as required If necessary adjust the spin speed or select RINSE HOLD GEEN CENTR SANS ESSOR Start the programme by pressing the START PAUSE START PAUZE MARCHE PAUSE button When the programme is finished Important If the programme ends at Rinse Hold select PUMP OUT POMPEN VIDANGE SPIN CENTRIFUG ESSORAGE or GENTLE SPIN KORT CENTRIFUG ESSOR DELICAT before opening the door Open the door and take out the washing The door can be opened after the END EINDE FIN indicator is lit Switch off the machine Set the programme selector to OFF UIT ARRET Add the Washing i is 1 Close the filling door securely For the maximum filling quantities refer to t
39. special button A Unscrew the four screws F using the special button A Remove the transport rail G Screw the four screws F back in Close off the two large holes with the plug caps B Attention Push in the plug caps so firmly that they engage in the rear panel this protects the inside of the unit against splash water 0 C D Setting up and connection instructions Prepare the Installation Location e The installation surface must be clean dry and free of floor wax resi due and other lubricating coatings so that the unit does not slide away Do not use any lubricants as sliding aids e t is not recommended to set up the washing machine on deep pile carpets or on floor coverings with soft foam underlays as this would mean that the stability of the unit would not be guaranteed Use ordinary rubber mats as underlays in locations with small format tiles e Never use wood card or similar underlays to compensate for minor floor unevenness Always use the adjustable screw type feet of the machine e f for reasons of space it is not possible to avoid setting up the unit next to a gas cooker or coal stove Insert a thermally insulating panel between the washing machine and the cooker 85 x 57 cm This panel must have an aluminium foil on the side against the cooker e The washing machine must not be set up in a room where there is a danger of frost Frost damage e
40. tdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 Nurnberg http www aeg hausgeraete de Copyright by AEG 822 943 494 01 050503 02 Subject to change without notice
41. that they satisfy the technical con ditions e g voltage frequency installation instructions type of gas etc for the coun try concerned and that they can withstand the local climatic and environmental conditions For appliances purchased abroad the user must first ensure that they meet the qualifications required in Belgium Non essential or requested adjustments are not covered by the guarantee and are not possible in all cases Our consumer services department is always at your disposal even after the guarantee period has expired Address for our consumer services department ELECTROLUX HOME PRODUCTS BELGIUM Bergensesteenweg 719 1502 LEMBEEK Tel 02 363 04 44 Customer services Customer services Belgium Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek Province de Li ge S D E Rue Gaucet 26 4020 Liege Tel Consumer services 02 363 04 44 04 343 11 60 Fax 02 363 04 00 02 363 04 60 04 343 47 68 51 52 53 Index 54 Index C Care agent 10 17 19 Child safety feature 30 39 Conditioner 9 10 18 19 27 Cottons o ce are 11 16 25 27 Curtains eio ts tata tue 15 26 Customer service 29 30 51 55 D Delicates son a sas 12 16 Detergent 10 17 18 19 Detergent dispenser drawer 10 19 Drain pump 10
42. the programme adjusts to varying conditions in the wash for example type and quantity of clothes imbalance detected during spin cycle special rinses etc Instructions for use Changing the programme is 1 2 x i Changing or interrupting Press the START PAUSE START PAUZE MARCHE PAUSE button Turn the programme selector to OFF UIT ARRET The programme is stopped Set another programme if required Otherwise set the selector to PUMP OUT POMPEN VIDANGE SPIN CENTRIFUG ESSORAGE or GENTLE SPIN KORT CENTRIFUG ESSOR DELICAT and press the START PAUSE START PAUZE MARCHE PAUSE button the water is pumped out or the spin cycle begins The programme can be interrupted at any time by pressing the START PAUSE START PAUZE MARCHE PAUSE button it is then re started by pressing the button a second time A programme can only be changed after turning the programme selector to OFF UIT ARRET Selecting additional programme functions Additional programme functions SHORT KORT COURT or STAIN VLEKKEN TACHES can be selected after the programme has started Press the START PAUSE START PAUZE MARCHE PAUSE button Press the SHORT KORT COURT button or the STAIN VLEKKEN TACHES button Press the START PAUSE START PAUZE MARCHE PAUSE button again The programme continues Changing the spin speed The spin speed can still be changed or RINSE HOLD GEEN CENTR SANS ESSOR selecte
43. ur due to foreign bodies in the washing which can cause rust Attention Do not clean the stainless steel drum with acidic antiliming agents scouring agents containing chlorine or iron or steel wool Our Customer Service Department has suitable agents available ts Remove any rust deposits on the drum using a stainless steel cleaning agent Filling Door tx Check regularly whether there are deposits or foreign bodies in the rubber sleeve behind the filling door and if so remove them 29 Instructions for use What to do if Remedying Faults In the event of a fault try to solve the problem yourself with the aid of the information provided here If you call Customer Service to deal with one of the faults listed here or to remedy an operating fault the customer service technician s visit will not be free of charge even dur ing the warranty period e f the fault code E 0 E20 or EMB is shown in the multidisplay you may be able to remedy the fault yourself see Faults Table below When you have remedied the fault press the START PAUSE START PAUZE MARCHE PAUSE button With all other displayed faults E plus number or letter switch appli ance off and on again Reset the wash programme and press the START PAUSE button If the fault code is displayed again please contact the Customer Service department quoting the fault code 1 ru LOOPTUD E t LI TEMPS RESTANT Fault Possible Cause Remedy
44. ut of operation please bring it to your nearest recycling centre or to your dealer Instructions for use Environment Tips The pre wash cycle is not required for averagely dirty washing This saves washing powder liquid water and time and does not harm the environment e The washing machine is especially economical when you fully utilise the stated filling quantities For small amounts of washing use only half to two thirds the recom mended amount of washing powder liquid e Suitable pretreatment enables stains and small amounts of dirt to be removed You can then wash at a lower temperature Use the energy saving program to wash garments which are lightly to moderately dirty There is often no need for conditioner Try it once If you use a dryer your washing will become soft and velvety even without conditioner e n the case of medium to high water hardness hardness range Il or higher see Washing and Care Agents you should use water sof tener The washing powder liquid can then always be metered for hardness range soft Instructions for use Unit Description Front View Drawer for washing powder and care agent Screw feet height adjustable Drawer for Washing Powder and Care Agent Main detergent powder and water softener if required 10 In wash stain treatment Control panel
45. venly in the drum prior to spinning Remedy Tighten the hose coupling Check the outlet hose and replace if necessary Close the cover properly Stop the programme remove the item from the door Start the programme again Fasten the emergency drain hose correctly see Carrying out an emergency drain op eration If the emergency drain hose is loose contact Customer Service Clean the detergent dis penser drawer set the fabric softener tray firmly in posi tion Note the maximum wash load see Programme tables For easy care textiles select the EASY IRON STRIJKVRI SANS REPASSAGE pro gramme Always load the drum as ful as possible with a combina tion of large and small items Instructions for use Fault Washing is not spun sufficiently excess wa ter is still visible in the drum Error code ECU ap pears The RINSE SPOE LEN RINCAGE indicator flashes The door does not open while the appliance is switched on Possible Cause There is a kink in the outlet hose The maximum pump height outlet hose height 1m from from the support surface of the appliance has been exceeded The detergent solution pump is clogged At the syphon coupling The syphon is clogged The door is locked due to high water level or high temperature Remedy Straighten the hose Call Customer Service who have modification kits avail able as accessories for pump heights over 1m Sw
46. ver 40 C as stain removal agent is only effective at higher temperatures If the WOOLLENS WOL LAINE hand wash setting is selected the additional programmes are not able to be chosen any buttons that are pressed have no effect 13 Instructions for use 14 Consumption Values The values for selected programs in the following tables were deter mined under normal conditions However there is a helpful orientation aid for domestic operation Filling Quantity Water Energy Program Selector Temperature Wis eee in kWh COTTONS LINEN 95 WITTE BONTE WAS 5 49 1 80 BLANC COULEURS COTTONS LINEN 60 WITTE BONTE WAS 5 46 0 94 BLANC COULEURS COTTONS LINEN 40 WITTE BONTE WAS 5 54 0 60 BLANC COULEURS EASY CARES 40 KREUKHERSTELLEND 2 5 54 0 50 DEFROISSABLE DELICATES 30 FUNE WAS LINGE DELICAT 2s Eu bee WOOLLENS WOL LAINE y 2 47 0 25 Handwash 30 1 Note Program setting for a test in accordance with EN 60 456 The consumption values can deviate from the stated values depending on the water pressure hardness inlet temperature room temperature type and quantity of washing the washing powder liquid used fluctuations in the mains voltage and selected additional functions Before the First Wash t 1 Pull out the washing powder drawer slightly 2 Pour about 1 litre of water through the washing powder drawer into the washing machine With the next program start this will close the solution c
47. y So as to avoid more severe damage the defect must be brought to our attention imme diately Applying the guarantee is subject to the consumer providing proof of purchase show ing the purchase and or delivery date The guarantee will not apply if damage caused to delicate parts such as glass vitreous ceramic synthetic materials and rubber is the result of inappropriate use The guarantee cannot be called on for minor faults that do not affect the value or the overall reliability of the appliance The statutory warranty does not apply when defects are caused by a chemical or electrochemical reaction caused by water abnormal environmental conditions in general unsuitable operating conditions contact with harsh substances The guarantee does not apply to defects due to transport which have occurred outside of our responsibility Nor will the guarantee cover those caused by inadequate installa tion or assembly lack of maintenance or failure to respect the assembly instructions or directions for use Defects that result from repairs or measures carried out by people who are not qualified or expert or defects that result from the addition of non original accessories or spare parts are not covered by the guarantee Appliances that are easy to transport may be delivered or sent to the consumer services department Home repairs are only anticipated for bulky appliances or built in appli ances
Download Pdf Manuals
Related Search