AEG 70330 Washer User Manual
Contents
1. n the case of permanent connection A permanent connection may only be made by an authorised specialist Before putting the machine into operation ensure that the mains voltage and current type shown on the unit s rating plate correspond with those at the place where the machine is being installed The fuse rating is also found on the rating plate e The mains lead may only be replaced by the customer service or by an authorised electrician 38 Installation and connection instructions Installation of the appliance 1 Transporting the appliance Remove transportation protection I 1 Washing machines with curved panels are not suitable for installing under units Do not place the washing machine on its front or on its right side viewed from the front Otherwise electrical components can get wet e Never transport the unit without the transport safeguard Do not re move the transport safeguard until the appliance is at the installation location Transporting the unit without the transport safeguard can damage it e Lift the appliance neither by an open filling door nor by the base When transporting the unit with a sack trolley Attach the sack trol ley only at the side Important It is essential to re move the transport safeguard be fore putting the unit into operation Keep all parts of the transport safeguard in a safe place for possible later transport moving Open both hose holders on th2. A GENTLE RINSE Separate gentle rinsing e g for rinsing hand washed textiles 2 rinsing cycles liquid care agent from compartment amp 9 is rinsed in short spin B STARCHING Separate starching separate conditioner separate impregnation of damp washing 1 rinsing cycle liquid care agent from the compartment amp is rinsed in spin C PUMP OUT Pumping out the water after a rinse hold without spin CJ Rinse hold means The washing remains lying in the last rinsing water It is not spun D SPIN Pumping off the water after a rinse hold and spin or separate spin of hand washed cottons linen F SHORT SPIN Pumping off the water after a rinse hold and gentle spin or separate gentle spin of sensitive textiles easy cares delicates wool 11 Operating Instructions Additional Program Buttons The additional program buttons are for adapting the washing program to the dirtiness of the wash ing Additional programs are not reguired for washing which is not excessively dirty Various functions can be combined with each other depending on the program Uy PRE WASH Warm pre wash before the main washing cycle which follows on automatically with intermediate spin for k COTTONS LINEN without intermedi ate spin for ley EASY CARES and EY DELICATES E SOAKING wo 0 we 40 C wol Approximately 50 minutes at 30 C water temperature This is followed by the main washing cycl
3. Completion of the Washing Program Program Sequence Display Wo Before the start the program steps to be carried out uUo are displayed by the program sequence display O The current program step is displayed during the O washing program GO ky O gt Operating Instructions Change program Ux 1 Press the SHORT or fp STAIN button 3 x Changing or aborting the program Press the lt gt START PAUSE button Turn the program selector to O OFF The washing program is aborted If required set a new washing program Otherwise turn the program selector to C PUMP OUT and press the gt START PAUSE button The washing program can be interrupted at any time with the O START PAUSE button and can be continued by pressing the button again Changing the washing program is only possible after the pro gram selector has been turned to O OFF Select the additional program The additional programs QUICK or 3 STAIN can still additionally be selected after the program starts Press the START PAUSE button Press the lt gt START PAUSE button again The washing program is continued Change the Spin Speed During the washing program the spin speed can still be changed or CJ RINSE HOLD can be set Press the lt gt START PAUSE button Change the speed with the Spin speed TJ RINSE HOLD button Press the gt START PAUSE button again The washing pro
4. Liguid care agents possibly water softener conditioner finisher starch Operating Instructions Control Panel Spin speed RINSE HOLD button Program seguence display Additional program buttons DOOR display Program selector START PAUSE button OVER DOSING display Program selector The program selector defines the nature of the washing cycle e g water level drum movement number of rinses spin speed to suit the type of washing as well as the wash temperature O OFF Switches off the washing ma chine All other positions are switched on ky COTTONS LINEN Main washing cycle Cottons Linen Cottons Linen at 30 C to 95 C Du Position E ENERGY SAVING Energy saving programme at approx 67 C for slightly to normally dirty cottons extended washing time Cannot be combined with gt QUICK WASH Operating Instructions ke EASY CARES Main washing cycle for easy care textiles mixed fabrics at 40 C to 60 C Position EASY IRON Main washing cycle at 40 C for easy care textiles which with the aid of this program only have to be either gently ironed or not ironed at all KY DELICATES Main washing cycle for delicates at 30 C or 40 C J WOOLLENS amp Hand Wash Main washing cycle J cold to 40 C for machine washable woollens and for woollen textiles and silk with the care symbol Vu Hand Wash
5. 905 829 3980 Port Louis Tel 29917 31634 Fax 905 829 3985 Tel 25355 Australia Korea South Namibia ANDI Co Pty Ltd Core Incorp AEG NAMIBIA PTY LIM 9 Kingston Town Close 3 F Chewoo Bldg ITED Jeppe Street Oakleigh VIC 3166 200 Nonhyun Dong Northern Industrial Area Tel 03 9569 1235 Kangnam Ku Windhoek Fax 03 9569 1450 Seoul Tel 061 21 6082 4 Telefon 82 2 549 89 61 Fax 061 217838 Warranty conditions Customer service centres Bahrain Arabian Gulf A A Zayani amp Sons P O Box 9 32 Bahrain Tel 261060 Bulgaria Electrolux Bulgaria E O O D 91 Levski Blvd 1000 Sofia Tel 2 806676 Fax 2 980 5276 Cyprus Hadjikyrlakos t Sons Ltd Prodromou 121 P O Box 21587 Nicosia 1511 Service Telephones Nicosia 02 481226 Limassol 05 562182 Larnaca 04 633929 Paphos 06 932 699 Estonia Electrolux Estonia Ltd Mustam e tee 24 EE0006 Tallinn Tel 372 6 650 090 Fax 372 6 650 092 Hongkong Wo Kee Services Ltd 585 609 Castle Peak Road Kwai Chung N T Hongkong Tel 2494 4000 Croatia Electrolux D O O Suplova 7 10000 Zagreb Tel 1 61 19512 Fax 1 61 19513 Kuwait Arabian Gulf Ali Al Ghanim Est P O Box 10 83 Tel 5322463 Fax 5242114 Lebanon Adib amp Assaferi P O Box 539 Tripoli Latavia Electrolux Latavia Ltd Terlaton Street 42 44 1011 Riga Tel 371 2 297821 Fax 371 2 821286 Lthuania Electrolux Lthuania Verkui 29 2600 Vilnus Tel 372
6. Linen nn 10 15 25 26 0 Open the door ii 24 Over dosed Sana 24 P Pre wash 11 18 21 25 Pre wash detergent 9 21 Program sequence display 22 PUMP SOUL abon net aka 11 Q Quick wash 12 18 23 25 R Rating plate ii 9 43 51 Rinse hold 11 19 24 Risk of frost 22 222222 once 6 35 S S actas cia 11 15 Sl barata ina 13 SOAKING eie ihn 12 18 21 25 Spin na senken 11 19 23 26 Spots tina benua ma eta 23 25 SIT Les Ad ta tue 8 9 12 18 34 Stain removers 0 cee eee eee ees 21 Starching victor yaah 11 26 W Warranty 0 cece eee eee 6 30 47 Washing coloureds cece cece eee 14 lightly soiled 8 12 normally dirty 0 eee eee eee 8 Washing powder 9 17 Water hardness 00 cece e ee eeee 8 16 pump Off 11 24 SOFTENER aei ioc RAP belo 8 9 16 21 Woollens 11 15 25 26 hand washable 11 25 Service Service In the chapter What to do if some faults are listed which you can remedy yourself Look there first if a fault occurs If you do not find any information there please consult your Customer Service You can find the addresses and telephone numbers in the section Customer Service Centres Always prepare in advance for the discussion By doing so you will sim plify the diagnosis and the decision
7. Carry ing out emergency emptying Operating Instructions Child Safety e Packaging materials e g films polystyrene can be dangerous for children Risk of suffocation Keep packaging away from children Children frequently cannot recognise hazards involved in handling electrical appliances Therefore ensure that they are properly super vised during operation and never allow children to play with the washing machine there isa risk that they can lock themselves inside it Ensure that children or small animals do not climb into the washing machine s drum When disposing of washing machines pull out the mains plug destroy the door lock cut off the electrical supply lead and dispose of the plug and remaining cable This means that playing children cannot shut themselves in and cannot encounter a potentially lethal hazard General Safety Repairs to the washing machine may only be carried out by qualified specialists Incorrect repairs may result in significant risk to the user If repairs are necessary consult our customer service or your special ist dealer Never use the washing machine if the mains cable is damaged or the conrol panel work surface or base panel area are so badly damaged that the interior of the unit is openly accessible Switch off the washing machine before carrying out cleaning care and maintenance work Also pull the mains plug out of the socket or if it is permanently connected s
8. nee 10 Additional Program Buttons 20 11 Consumption Values and Time Requirements 13 Before the First Wash ii 13 Prepare washing Cycle 14 Sort washing and prepare sslsssssesseeee eh 14 Washing Types and Care Symbols ii 14 Detergents and care agents Wii 16 Which detergent and care agent nenn 16 How much detergent and care agent io 16 Water softener ns ans a een aa a dan 16 Run a Washing Cycle ii 17 Brief Instructions un Ka a 17 Set the Washing Program an 18 Change the spin speed select Rinse Hold nn 19 Opening and Closing the Filling Door 20 Add the washing nh 20 Add detergent care agent aaa 21 Start the Washing Program in 22 Completion of the Washing Program ii 22 Change program oo eee eect teenies 23 The washing cycle is finished Remove the washing 24 Contents Program tables oce aan 25 Washing runter panai ere ba aka rat 25 Separate conditioning starching impregnation ss 26 Separate rinse u ee ee MR BU NOR IP BU ER 26 Separate SPIN u uns cce A UT ng Po An Es 26 Cleaning and Care RS 27 Control panel nern RE rn 27 Detergent Drawer no sen aan 27 Washing Drum iiu oce tts fy add a pe prc pcees ri 28 Main door Pm 28 Cleaning the drain pump sseeseesese II 29 Wha
9. 272 3326 Fax 372 272 3366 New Zealand Euro Life New Zealand Ltd Privat Bag 58 Symonds Street Auckland Tel 09 525 2222 Nowvelle Caledonie Socometra N C B P 483 Nouman Tel 275444 Oman Moshin Haider Darwish P O Box 1 35 Muscat Tel 703743 Poland Electrolux Poland Sp zo o ul Domaniewska 41 02 034 Warszawa tel 022 874 33 33 fax 022 874 33 00 Russia Electrolux Russia Ltd 16 Olympiysky prospekt 129090 Moscow Tel 095 937 7837 Fax 095 926 5513 Warranty conditions Customer service centres Israel Electricity amp Electronic Services Evis LTD 19 Hataasia st Raanana Industrial area 43654 Tel 972 9 7448118 Fax 972 9 7603618 e mail evis evis co il Japan Electrolux Japan Ltd Malaysia Arzbergh Engineering No 49A B Jalan Petaling Utama 7 4600 Petaling Jaya Tel 3 795 1084 Fax 3 795 1082 Singapore Arzbergh Engineering Yasuda Warehouse 4F 3 3 12 19 Tanglin Road 06 07 Heiwajima Ota Ku Tokyo Tel 81 3 3544 3363 Fax 81 3 3763 6143 Thailand OLYMPIA Thai Ltd 44 Ratchadapisek Road 10320 Bangkok Tel 2 513 6111 Fax 2 513 2574 Hungary Electrolux Lehel KFT AEG Div Erzsebet Kiralyne Utja 87 1142 Budapest Tel 00361 251 84 44 Singapore 247909 Tel 65 7356572 Fax 7351124 Slovakia Rep Electrolux Slovakia S R O Seberiniho 1 821 03 Bratislava Tel 02 4333 4322 4355 Fax 02 4333 6976 USA ANDI Co Appl Inc East
10. displays o DOOR and lt gt START PAUSE show whether the door can be opened while the 0 90 Q appliance is switched on Display gt DOOR Display gt O START PAUSE Opening door possible Glows green Flashes red Yes Yes after pressing button Glows green Glows red O 0 START PAUSE Is off Flashes or glows red No 1 The main door is locked because of a high water level or a high temperature If the display o DOOR flashes red and the display VJ MAIN WASH flashes you tried to start a washing program without first closing the main door properly In this case push the door shut firmly and restart the washing program the washing For the maximum filling quantities see the Program tables See Sort and prepare washing for information on correctly preparing the washing Sort and prepare the washing according to type Open the filling door Pull on the handle of the filling door Fill with washing Important When closing the door make sure no items of washing get stuck This could damage textiles and the unit Close the filling door securely Operating Instructions Add detergent care agent T is 1 Open the detergent drawer grip inside Filling with washing detergent For information on detergent and care agents refer to the section De tergents and care agents the flap on the drawer at the bottom 1 and pull out the drawer as far as it will go 2 care a
11. impair the function Check the laying of the drainage hose and eliminate the bend if necessary or clean the solution pump and if required remove foreign bodies from the pump housing Meter the detergent exactly in accordance with the manufacturer s information Tighten the intake hose screw connection Check the drainage hose and replace it if necessary Close cover correctly Stop the program remove washing from the door start a new program Shut the emergency drain hose off properly see section Carrying out emergency drainage Call your after sales service if the emer gency drain hose is not wa ter tight 31 Operating Instructions 32 Problem Conditioner not added compartment amp for care agent full of wa ter Washing heavily creased Washing not well spun Residual water still vis ible in the drum The indicator RINSE flashes Possible Cause Softener insert in the com partment for care agent not correctly attached or is blocked Too mush washing probably put in Drainage hose bent Maximum pump head outlet head 1m from unit s floor surface exceeded Solution pump blocked If a siphon is connected Si phon blocked Remedy Clean the detergent drawer and firmly attach the sof tener insert Pay attention to the maxi mum filling guantity see Program Tables For easy care textiles select the program Al EASY IRON Remove
12. on whether customer service is necessary Note the PNC number and S num ber You will find both on the rating plate on the inside of the door of your washing machine S NOx ais Answer as precisely as possible e What form does the fault take Under what circumstances does the fault occur When do you incur costs even during the warranty period f you could have remedied the fault yourself with the aid of the fault table see the section What to do if If several journeys by the customer service technician are necessary because for example he did not receive all the important information before his visit and must collect spare parts These multiple trips can be avoided if you prepare your phone call as described above 51 AEG Hausgerite GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de Copyright by AEG 822 942 848 01 150302 04 Subject to change without notice
13. the bend Consult Customer Service They can supply a retrofit kit as a special accessory for de livery heads of more than 1m Switch off the unit and pull out the mains plug Clean the solution pump Clean the siphon Operating Instructions Problem The main door cannot be opened while the appliance is turned on Washing detergent residues form in the washing detergent drawer The rinsing water is murky The corresponding display does not light up when one of the ad ditional program but tons is pressed Possible Cause The main door is locked be cause of a high water level or a high temperature The dis play o DOOR is not lit Power failure All displays have gone off For safety reasons the door remains locked for 4 to 5 minutes Water valve not fully opened Filter in the screw connec tion of the intake hose on the water valve or on the unit is blocked The cause is probably a de tergent with a high silicate content The selected additional program cannot be combined with the set program Remedy Wait until the indicator o DOOR lights up green Should it nevertheless be necessary to open the main door Turn the programme knob to OFF turn the pro gramme knob to C PUMP OUT Press button H amp 2 START PAUSE The main door can be opened after the water has been pumped out If water can be seen through the window in the door first carry out e
14. you about the following safety instructions Before Using for the First Time Refer to the Installation and Connection Instructions further on in this user information e f units are delivered in the winter months at minus temperatures Store the washing machine at room temperature for a few hours be fore putting it into operation Correct Use The washing machine is only intended for washing normal domestic washing If the appliance is used for a wrong purpose or wrongly op erated the manufacturer cannot assume any liability for any dam ages Additions or modifications to the washing machine are strictly for bidden due to safety reasons Use only detergent which is suitable for washing machines Refer to the detergent manufacturer s instructions he washing must not contain any flammable solvents Also bear this in mind when washing pre cleaned washing Do not use the washing machine for dry cleaning Dyes dye removing agents may only be used in the washing machine if the manufacturer expressly permits use of these products We can not accept liability for any damage e Use only water from the water mains Use rain water or service water only if it meets the requirements defined in DIN 1986 and DIN 1988 e Frost damage is not covered by the warranty If the washing machine is in a room subject to possible frost hazards emergency emptying must be carried out if there is a risk of frost see the Section
15. 65 Campus Plaza Edison New Jersey 0837 USA Tel 201 2258839 Saudi Arabia Alia Trading Corporation P O Box 4101 King Abdul Aziz Street Riyadh Tel 4645977 Al Nahas Est Musaidia Market P O Box 1 15 29 Jeddah Tel 6606852 Slovenia Electrolux Slovenia D O O Traska Ul 132 1000 Ljubljana Tel 61 1234 137 Fax 61 1234 238 South Africa AEG Pty Ltd 55 12th Road P O Box 1 02 64 Kew Johannesburg 2000 Tel 8069111 Syria Masri amp Shami P O Box 24 96 Damascus Tel 214080 49 Index 50 INDEX A Abort program eee eee eee 23 C Care agent ca NAN emo 9 17 Change program ii 23 Child safety feature 30 37 Clothes sensitive 15 Conditioner 9 11 16 21 26 COLLODS c are 10 15 25 26 Curtains an oo 14 25 Customer Service 28 30 51 D Delicates ra 11 15 25 Detergentes ass Diana 9 16 21 Detergent dispenser drawer 9 Detergent drawer 000 21 Door opening ii 20 33 Drain PUMP 9 29 E Easy OM u a ben deed 11 15 25 32 Easy cares io 10 15 25 Emergency drainage 35 Energy saving ii 10 25 F Fabric softener asn debina 21 Filling quantity ii 13 25 G Gentle rinse oooooococcon o 11 26 H Hand wash ssss 11 25 26 In wash stain treatment 9 L
16. Installation and connection instructions 42 Compensate for floor unevenness is 1 Adjust the screw feet so that the If necessary check the setting Floor unevenness can be compensated for and the height can be cor rected with the four adjustable screw feet The height can be adjusted in the range 10 5mm To adjust the feet use the special spanner supplied for removing the transport braces Slide the special key firmly onto the hexagon head of the threa ded foot as far as it will go unit is horizontal and stable The unit must not wobble over when loaded with a spirit level Important Minor unevenness of the floor surface should never be levelled out by laying pieces of wood card or similar materials but rather should always be com pensated for by adjusting the adjustable feet Installation and connection instructions Electrical connection ce Water connection i Permissible water pressure Details of the mains voltage current type and required fuses can be found on the rating plate The ra ting plate is located at the top above the filling door For permanent electrical connection within the electrical circuit provi sions must be made which allow for electrical disconnection of the ap pliance from the mains with a contact opening of at least 3 mm at all poles Suitable devices include circuit breakers fuses threaded fuses must be entirely removed from the so
17. OKO LAVAMAT 70330 The environmentally friendly washing machine User information Dear Customer Please read this user information carefully Pay particular attention to the section Safety on the first Info pages Please keep this user information in a safe place for later reference Pass it on to any future owners of the unit The warning triangle and or signal words Warning Caution Impor tant emphasise information which is important for your safety or for the unit s functional reliability It is imperative that this information is observed his symbol guides you step by step through the operation of the appli ance Next to this symbol you will find additional information and practical tips on using the appliance Tips and information on economical and environmentally responsible use of the unit are identified with the clover leaf For any faults which occur this user information contains information on how to remedy these faults yourself See the section What to do if Printed on recycled paper Thinking ecologically means acting ecologically Contents CONTENTS Operating Instructions Jo 6 STI A EET 6 Disposal 2 n RE URS 8 Environmental tips ii 8 Unit description iioii e eter Pe EG ns 9 Front VIEW Caicara aan Ba anna ad 9 Drawer for detergent and care agent aa 9 Control Panel axes pter pepe ean le ben naa IE Mees 10 Program selector
18. aces with small format tiles lay a conventional rubber mat underneath Minor unevenness of the floor surface should never be levelled out by laying pieces of wood card or similar materials but rather should al ways be compensated for by adjusting the screw feet e f for space reasons it is not possible to avoid setting up the unit di rectly next to a gas or coal fired cooker install a thermal insulation panel between the cooker and washing machine 85 x 57cm which must have an aluminium film on the side against the cooker The washing machine must not be set up in a room where there is a danger of frost Frost hazard e Flexible feed and drain tubings may not be crinkled or squeezed Installation on a concrete base If the unit is set up on a concrete base for safety reasons it is essential to fit stand plates in which the washing ma chine is adjusted The stand plates are available from Customer Service under the spare parts number 645 425 058 O Installation on vibrating floors Where the floor vibrates particularly in the case of wooden beam floors with pliable boards securely screw a water resistant wooden panel at least 15mm thick onto at least 2 floor planks If possible set up the unit in the corner of a room as the wooden floor is optimally re strained there and is therefore least likely to be subject to resonance vi brations 41
19. ary to empty the collecting vessel several times To do this close the emergency drainage hose temporarily with the plug 35 Operating Instructions 36 When the water is completely drained 6 Push the plug securely into the emergency drainage hose and turn it clockwise to secure it 7 Replace the emergency drainage hose in its holder 8 Put on the flap and close Additional Rinse RINSE The washing machine is set for extremely economical water consump tion However for persons who suffer from allergies it can be helpful to rinse with more water If RINSE is set an additional rinse is carried out with the pro gram ky COTTONS LINEN kw EASY CARES T EASY IRON and YY DELICATES No additional rinse is set when the unit is delivered Set additional rinse Turn the program selector to k COTTONS LINEN wey EASY CARES AT EASY IRON and Y DELICATES with any temperature Keep the VL J PRE WASH and gt 4 QUICK buttons pressed simultane ously for at least 2 seconds RINSE lights up on the program sequence display The additional rinse is set It remains saved until you cancel it again The additional rinse increases water consumption and the program run time Cancel additional rinse Again turn the program selector to ke COTTONS LINEN wey EASY CARES 2 EASY IRON or Y DELICATES Keep the VL PRE WASH and gt QUICK buttons pressed s
20. cket ground fault circuit inter rupters and contactors Permanent connection may only be carried out by an authorised electrician This appliance complies with the following EC directives The Low Voltage Directive 72 23 EU with changes The EMC Directive 89 336 EU with changes The washing machine has safety features which prevent back contami nation of the drinking water and which conform to the national regu lations of the water authorities e g for Germany DVGW guidelines This means that additional protective measures in the installation are not necessary Important Units for connecting to cold water must not be connected to hot wa ter Use only new hose sets for the connection The water pressure must be at least 1 bar 10 N cm 0 1 Mpa max imum 10 bar 100 N cm 1 Mpa f more than 10 bar Connect a pressure reduction valve upstream e f less than 1 bar Unscrew the inlet hose on the unit side at the sole noid intake valve and remove the flow regulator to do this remove the filter with pointed pliers and take out the rubber washer behind Replace the filter 43 Installation and connection instructions 44 Water inflow Connect the hose with the angled connection to Connect the hose with the By slowly opening the water valve before A pressure hose of 1 35m in length is supplied Ifa longer inflow hose is reguired
21. diesen L ndern gelten die Garantiebedingungen der rtlichen Partner Diese k nnen dort eingesehen werden Further after sales service agencies overseas In these countries our AEG agents own guarantee conditions are applicable Please ob tain further details direct Autres agences trang res assurant le service apr s vente Dans ces pays les conditions de garantie des concessionnaires de la r gion sont vala bles Vous pouvez les consulter sur place Otros puntos de Postventa en el extranjero En estos pa ses rigen las condiciones de nuestros representantes locales las cuales pueden ser consultadas all mismo Ulteriori uffici del servizio tecnico assistenza clienti all estero In questi paesi sono valide le condizioni di garanzia dei partner locali Queste condizioni possono essere esaminante sul luogo Servicos de assist ncia t cnica no estrangeiro Nestes pa ses s o v lidas as condic es de garantia dos concession rios locais podendo a ser consultadas U A E Abu Dhabi Jordan Malta Universal Trading Company Jordan Household ITC P O Box 43 99 Supply Co Ltd International Trading Com Tel 335331 P O Box 3 68 pany Amman Tel 69 70 50 White House Building Mountbatte Street Blata L Bajda Tel 220644 Egypt Kanada Mauritius Middle East Commercial EURO LINE Appliances Happy World Centre Ltd Center 2150 Winston PARK Drive 20 P O 7 54 P O Box 19 Oakville Ontario L6H 5V1 1 Chausee Street Kairo Heliopolis Tel
22. e gt QUICK WASH Shorter washing cycle for slightly dirty washing Q STAIN For treating very dirty washing or stained washing In wash stain treat ment is added during the program on a time optimized basis May only be used for wash temperatures from 40 C as stain removers only be come effective at higher temperatures With the J WOOLLENS amp Hand Wash program it is not possible to select the additional programs any pressed buttons have no effect Operating Instructions Consumption Values and Time Reguirements The values for selected programs in the following tables were deter mined under normal conditions However there is a helpful orientation aid for domestic operation Program Selector Filling Ouantity Water Energy Time Temperature in kg in Litres inkWh in Minutes k COTTONS LINEN 95 5 49 1 80 144 lks COTTONS LINEN 60 5 49 0 94 131 k COTTONS LINEN 40 5 54 0 60 128 tey EASY CARES 40 2 5 54 0 50 82 Y DELICATES 30 2 5 50 0 30 55 19 WOOL Q Handwash 30 2 47 0 25 55 1 Note Program setting for a test in accordance with EN 60 456 The consumption values can deviate from the stated values depending on the water pressure hardness inlet temperature room temperature type and quantity of washing the washing powder liquid used fluctuations in the mains voltage and selected additional functions Before the First Wash TS 1 Pull out the washing powder drawer slightly 2 Pour abo
23. e unit s rear side and remove the hoses and mains cable 2 G GA IN GB 0 Tao 39 Installation and connection instructions 40 2 Pull both hose holders off the unit with a strong pull The special key E and the caps D 2 each and G 1 each are sup plied with it 3 Unscrew the two screws with the special spanner 4 Unscrew the 4 screws B with spe cial spanner E 5 Remove the transport rail C Screw the 4 screws B back in 7 Close the 2 large holes with the caps D Important Press in the caps with sufficient strength so that they engage in the rear panel protects the inside of the units against splash water 8 Remove the screw F including the compression spring with the spe cial spanner E 9 Close the hole with the cap G Important Press in the cap with sufficient strength so that it en gages in the rear panel protects the inside of the unit against splash water eo Installation and connection instructions Prepare the installation place e The installation surface must be clean and dry free of floor polish residues and other greasy coatings so that the unit does not slip away Do not use lubricants as a sliding aid Installation on a high veil carpet or floor tiles with soft sponge backs is not recommended because the standing safety of the appliance is then no longer ensured e By installation surf
24. ease bring it to your nearest recycling centre or to your dealer el Environmental tips e A pre wash cycle is not necessary in the case of washing which is not excessively dirt This saves detergent water and time and is gentle on the environment e If the indicated load capacities are taken full advantage of the wash ing machine is especially efficient e For small loads use only one half to one third of the recommended detergent quantity e Suitable pre treatment enables marks and limited amounts of dirt to be removed You can then wash at a lower temperature e Wash slightly to normally dirty cottons with the energy saving pro gram e There is often no need for the softener Try it once If you use a drier your washing will become soft and fluffy even without a softener e In the case of medium to high water hardness hardness range runs to upwards see Detergent and care agents you should use a water softener The detergent can then always be metered for hardness range soft Operating Instructions Unit description Front view Drawer for de tergent and care agent Control panel Rating plate be Screw feet height adjustable Drawer for detergent and care agent Stain removers Main wash detergent powder form and MN hind filling door Main door Flap in front of drain pump Pre wash detergent soaking agent or water softener
25. en excess dye in new coloured items It is best to wash such items separately the first time Mix small and large items This improves the washing effect and the washing is more favourably distributed during spinning e Fluff washing before placing into the washing machine Do not place folded washing into the drum e Pay attention to the care instruction wash separately and wash separately several times Washing Types and Care Symbols The care symbols help you chose the correct washing program The washing should be sorted according to type and care symbol The tem peratures shown in the care symbols are the maximum temperatures in each case Operating Instructions Cottons Textiles made of cotton and linen which carry this care symbol are in sensitive to mechanical stress and high temperatures The programm ky COTTONS LINEN is suitable for this type of washing Linen Textiles made of cotton and linen which carry this care symbol are in sensitive to mechanical stress The programm ky COTTONS LINEN is suitable for this type of washing Easy care washing Textiles such as treated cotton cotton mixed fabrics viscose and syn thetics which carry this care symbol require chemically more gentle treatment The program wy EASY CARES I EASY IRON is suitable for this type of washing Delicates Textiles such as layered fabrics micro fabrics viscose synthetics and cur tains which carry this care symbol requi
26. gent Compartment for in wash stain treatment Compartment for powder main detergent If you use water softener and require the right compartment for the pre wash soaking detergent add the water softener to the main detergent in the left compartment Compartment for liquid care agent Softener finisher starch Important Fill the compartment at most to the MAX mark Fill any viscous agent up to the MAX mark Dissolve powdery starch Note It is normal for a small amount of water to be left in the compartment for liquid care agent this will not affect the wash results Compartment for pre wash soaking detergent Only for auxiliary programs Uy PRE WASH SOAKING or for water softener Push the drawer fully in If using liquid detergent tabs Add liquid detergent tabs in the amount recommended by the was hing detergent industry Follow the instructions on the washing deter gent package 21 Operating Instructions 22 Start the Washing Program r amp 1 Check that the water valve is open 2 Start the washing program Press the button H O START PAUSE The washing program is started 0 8 o i The filling door is not correctly closed if the indicators o DOOR and VJ MAIN WASH flash red when the button D amp START PAUSE i is pressed In this case press the filling door firmly closed and press the button Q START PAUSE again
27. gram is continued 23 Operating Instructions 24 The washing cycle is finished Remove the washing I 1 aon 5 cc After a washing program has ended END lights up on the program sequence display If J RINSE HOLD was selected the display next to the START PAUSE button flashes After a rinse hold it is first necessary to pump off the water Either press the lt gt START PAUSE button the water is pumped off the and the washing is spun according to the finished program After the gt START PAUSE button is pressed again the spin speed can still also be changed during spinning or Turn the program selector to C PUMP OFF and press the H O START PAUSE button the water is pumped off without spinning or Turn the program selector to D SPIN or F SHORT SPIN and press the lt D O START PAUSE button the water is pumped off and the wash ing is spun or gently spun After the end of this program step the END indicator will illumi nate Open the filling door As soon as the DOOR indicator lights up green the filling door can be opened Remove the washing Turn the program selector to OFF Close the water valve After washing pull out the washing detergent drawer slightly so that it can dry out Only lean the door against the washing machine so that the latter can air out If the indicator C OVERDOSING lights up too muc
28. h deter Po gent was used in the washing program just ended Observe the dosing recommendations of the detergent manufacturer as well as the filling quantity for the next wash Important If the washing machine is not used for a long time Close the water tap and disconnect the washing machine from the electricity mains Operating Instructions Program tables Washing Not all possible settings are listed below only those which are normal and appropriate in everyday use Type of washing max Program selector possible yp 9 filling quantity 9 additional care symbol i 1 temperature dry weight programs UJ PRE WASH Cottons e lay COTTONS LINEN tz SOAKING 3 95 gt QUICK WASH Gp STAIN Energy saving Uy PRE WASH program 5 kg E E SOAKING Cottons GaP STAIN UJ PRE WASH Linen E key COTTONS LINEN Xe SOAKING 3 30 to 60 gt QUICK WASH EP STAIN 25 kg I CARES LJ PRE WASH Easy Cares E SOAKING 3 gt QUICK WASH EASY IRON 1 kg GP STAIN er UJ PRE WASH Delicates 29 3 DELICATES t SOAKING or N 30 40 gt QUICK WASH curtains Lag STAIN Woollens amp y HAND WASH Hand Wash 2 kg J WOOLLENS v COLD to 40 1 A 10 litre bucket holds approximately 2 5 kg of dry washing cotton 2 In the case of the STAINS a minimum temperature of 40 C is required for the stain remover to become effective 3 Creases in the washing are only largely prevented if the fi
29. he mains plug before cleaning the drain pump First carry out emergency emptying see section Carrying out emer gency emptying Place a towel on the floor in front of the cover of the drain pump Re sidual water can run out clockwise and pull it out pump housing the cover laterally into the guide slots and screw on the cover securely clock wise place it in the holder 29 Operating Instructions What to do if Remedying Faults In the event of a fault try to solve the problem yourself with the aid of the information provided here If you call Customer Service to deal with one of the faults listed here or to remedy an operating fault the customer service technician s visit will not be free of charge even dur ing the warranty period Problem Possible Cause Remedy The mains plug is not plugged in Plug in the mains plug The fuse of the building s Eu Repl he fuse wiring is not in order Shed The washing machine does not work The filling door is not cor Close the filling door The rectly closed lock must engage audibly The button 4 amp START Press the button HW O PAUSE was not pressed for START PAUSE until the pro long enough gram begins Cancel the child safety fea ture see the section Child Safety Feature The filling door cannot The child safety feature is be closed set The indicators o ITI Duce quM ese Cubs WASH f
30. imultane ously for at least 2 seconds RINSE goes out on the program sequence display The additional rinse is cancelled Operating Instructions Child Safety Feature If the child safety feature is set the filling door can no longer be closed and no washing program can be started Setting the child safety feature Use a coin to turn the rotary knob on the inside of the filling door clockwise as far as it will go Warning The rotary knob must not be in a vertical position after adjustment otherwise the child safety feature is not active The ro tary knob must project as shown in the diagram Cancelling the child safety feature Turn the rotary knob anticlockwise as far as it will go M x at 37 Installation and connection instructions Installation and connection instructions Installation Safety Precautions Do not tilt the washing machine onto its front or onto its right side viewed from the front Electronic components can get wet Check the washing machine for transport damages A damaged unit must never be put into operation under any circumstances In the event of damage please contact your supplier Ensure that all parts of the transport safeguard are removed and that the unit is splash protected see Removing transport safeguard Otherwise the units or neighbouring furniture can be damaged when spinning Always insert the plug into a correctly installed earthed socket
31. ing type refer to the Program Tables Set the program selector to the required washing program with the required temperature Select any additional programs uJo The indicator for the selected additional program lights up Press another button to make different selection E 0 Press the button again to deselect Operating Instructions Change the spin speed select Rinse Hold pe If necessary change the spin speed for the final spin se lect C RINSE HOLD Press the Spin speed J RINSE HOLD button as often as necessary until the display for the required spin speed or of L RINSE HOLD lights up If CJ RINSE HOLD is selected the washing remains in the last rinsing water It is not spun If you do not change the spin speed the final spin is au tomatically adapted depending on the washing program huy COTTONS LINEN 1000 O 900 700 400 Wo 1000 revolutions per minute key EASY CARES Y EASY IRON 900 revolutions per minute Y DELICATES 700 revolutions per minute J WOOLLENS amp Hand Wash 900 revolutions per minute The speed of the intermediate spin depends on the selected program and cannot be changed 19 Operating Instructions Opening and Closing the Filling Door pe pe ble Add H p 1 2 3 20 Open Pull on the handle of the filling door ro Close Press the filling door firmly closed The
32. lash y i y progran Water valve not closed Open the water valve Close the water valve Un screw the hose from the wa No water runs in Filter in screw connection of ter valve remove the filter and clean it under running water The indicator the intake hose blocked RINSE flashes Water tap is blocked with Check water tap and have it limescale or is faulty repaired if necessary Operating Instructions Problem The washing machine vibrates during opera tion or it is on an une ven surface The washing solution of the main wash froths up a lot Water runs out under the washing machine Possible Cause The transport packaging has not been removed The height adjustable screw feet are not correctly set There is not much washing in the drum e g only one dressing gown The water could not be com pletely pumped off before spinning because the drain age hose is bent or the solution pump is blocked Too much detergent was probably used The screw connection on the intake hose is leaky The drainage hose is leaky The washing solution pump cover is not correctly closed Washing stuck in the filling door The emergency drain hose is not properly shut off or it is not water tight Remedy Remove transport packaging according to the installation and connection instructions Adjust in accordance with the installation and connec tion instructions This does not
33. lling quantity of 1 kg is maintained 5 to 7 easy care men s shirts are equivalent to approximately 1 kg of dry wash ing 25 Operating Instructions Type of washing Cottons Linen Separate rinse Type of washing Cottons Linen Easy Cares Delicates Woollens Hand Wash Separate spin Type of washing Cottons Linen Easy Cares Delicates Woollens Hand Wash 26 Max Filling guantity dry weight 5 kg Max Filling guantity dry weight 5 kg 2 5 kg 2 5 kg 2 kg Max Filling guantity dry weight 5 kg 2 5 kg 2 5 kg 2 kg Separate conditioning starching impregnation Program selector B STARCHING Program selector A GENTLE RINSE Program selector D SPIN F SHORT SPIN Operating Instructions Cleaning and Care Control panel Important Do not use any furniture cleaning agents or aggressive cleaning agents in order to clean panel and control parts Wipe control panels with a damp cloth When doing so use warm wa ter Detergent Drawer S1 2 3 4 Clean the compartments with warm The detergent drawer should be cleaned from time to time Pull the detergent drawer out as far as it will go Remove the detergent drawer by pulling sharply Take the conditioner insert out of the middle compartment Clean the conditioner insert under running water water from the rear side It is best to use a flat brush Push on the conditioner in
34. mergency empty ing see section Carrying out emergency drainage After approx 4 to 5 minutes the door can be opened again by pulling the handle Open the water valve fully Close the water valve Un screw the intake hose from the water tap and from the unit Clean the filter No negative influence on the rinsing result possibly use liquid detergent if necessary Make another selection 33 Operating Instructions 34 If the washing results are not satisfactory If the washing has turned grey and if limescale is deposited in the drum then Too little detergent was used he wrong detergent was used Special soiling was not pre treated Program or temperature not set correctly e If multi component detergents are used the individual components were not used in the correct ratio If there are still grey spots on the washing Washing soiled with ointments grease or oils was washed with too little detergent Too lower temperature was used for washing A frequent cause is that softener particularly that in concentrated form has reached the washing Wash out such spots quickly and use the softener concerned carefully If at the end of the last rinse foam is still visible Modern detergents can also cause foam in the last rinse However the washing is still sufficiently rinsed If there are white remnants on the washing These are insoluble components of modern detergen
35. on types Eg Secure the connection between the grommet and siphon with a hose clamp Water drain off inside a basin Important Small basins are not suitable for drainage Water could overflow The end of the drainage hose must not be submerged in the pumped out wa ter Otherwise the water could be sucked back into the unit When hanging in a wash basin or a bath tub the drainage hose must be secured with the supplied attachable bend to prevent it slipping The back surge force of the escaping water could otherwise force the hose out of the basin gt Tie the bend to the tap or the wall using a piece of string 45 Installation and connection instructions 46 Delivery heads over 1m To pump off the washing rinsing solution every washing machine has a drain pump which carries liguids up to a height of 1m via the drain age hose calculated from the machine s standing surface Please contact Customer Service for delivery heads of over 1m Technical data Adjustment possibility Approx 10 5mm Filling guantity program dependent max 5kg Area of use Domestic Drum speed spinning See rating plate Water pressure 1 10 bar 10 100 N cm 0 1 1 0 Mpa Dimensions 10 850 5 dimensions in mm Warranty conditions Customer service centres Warranty conditions Customer service centres Weitere Kundendienststellen im Ausland In
36. only a VDE approved complete set of hoses with fitted hose screw connections offered by our Customer Service is permissible Hose sets in lengths of 2 2m 3 5m and 5m are available for washing machines without Agua Control Hose sets in lengths of 2 0m 2 9m and 3 5m are available for washing machines with Aqua Control Important Never cut into pieces in order to extend the hoses Sealing rings are supplied either in the plastic nuts of the hose screw connection or in the enc losed pack Do not use other seals the machine Important Do not lay the inlet hose verti cally downwards instead run it to the right or left as shown in the diagram Tighten the hose screw connec tion only by hand straight connection to a water valve with a screw thread R 3 4 inches Important Only tighten the screw connection manually putting the washing machine into operation check that the connection is free of leaks Installation and connection instructions Water drain The drainage hose can either be connected to a siphon or hung in a wash basin or discharge basin or a bath tub Only original hoses may be used for extensions max 3m laid on the floor and then up to 80cm high Customer Service stocks drainage hoses in lengths of 2 7 and 4m Important It is essential to lay the drainage hose without kinks Water drain off inside a siphon The grommet on the hose end fits all standard siph
37. provide information on the local water hardness Since the water softener is rinsed in before the main detergent water pre softening 80 of the stated quantity of softener shown on the package is sufficient Water hardness details Water hardness in dH Water hardness in mmol Hardness class E E German hardness scale millimol per litre soft 0 7 to 1 3 II medium hard 7 14 1 3 2 5 Ill hard 14 21 2 5 3 8 IV very hard greater than 21 greater than 3 8 Operating Instructions Run a Washing Cycle Brief Instructions is 1 om fF WN A washing cycle is run in the following steps Set the correct washing program Set the program and temperature with the program selector Set any additional program s If necessary change the spin speed select TJ RINSE HOLD Open the filling door and fill with washing Close the filling door Add washing detergent care agent Start the washing program with the Q START PAUSE button After the Washing Program Ends Attention If the washing cycle ended with Rinse Hold before opening the filling door carry out C PUMP D SPIN or F SHORT SPIN Open the filling door and remove the washing Switch off the washing machine Set the program selector to OFF 17 Operating Instructions Set the Washing Program I 1 For a suitable program the right temperature and possible additional programs for the relevant wash
38. re particularly gentle treatment The program Y DELICATES is suitable for this type of washing Wool and especially sensitive washing i Textiles such as wool wool mixtures and silk which carry this care sym bol are particularly sensitive to mechanical stress The program amp WOOLLENS y Hand Wash is suitable for this type of textile Important Textiles with the care symbol do not wash must not be washed in washing machines 15 Operating Instructions Detergents and care agents Which detergent and care agent Use only detergents and care agents which are suitable for use in wash ing machines Always follow the manufacturer s instructions How much detergent and care agent The reguired guantity depends upon extent of soiling of the washing on the hardness class of the mains water e the amount of washing If the detergent manufacturer does not give any metering quantities for small loads add a third less for half a load or only half the amount of detergent for small loads for EASY IRON which is recommen ded for a full load Observe the instructions for use and dosing provided by the detergent and conditioner manufacturer Water softener For medium to high water hardness hardness class II upwards you should use softener Refer to the manufacturer s instructions Then al ways add the appropriate amount of detergent for hardness class soft The responisable water works will
39. sert as far as it will go so that it is securely in place 27 Operating Instructions 7 Use a brush to clean the entire rinsing in section of the washing machine particularly also the noz zles on the top side of the rinsing in chamber 8 Set the detergent drawer into the guide tracks and push in Washing Drum The washing drum is made of stainless steel Rusting foreign bodies in the washing can cause rust deposits on the drum Important Do not clean the stainless steel drum with decalcifying agents containing acids scouring agents containing chlorine or iron or steel wool Our Customer Service can provide suitable agents rs Remove any rust deposits on the drum using a stainless steel cleaning agent Main door rs Check ona regular basis to see if deposits or foreign objects are present in or at the rubber sleeve behind the door and remove 28 Operating Instructions Cleaning the drain pump Unscrew the drain pump cover anti Remove any foreign bodies from the Replace the cover Insert the webs on Close the emergency emptying hose and Close the flap Paper clips nails and so on can sometimes get into the washing ma chine with the washing and remain in the drain pump casing Fluff and strands of fabric can gather on these items and block the drain pump Therefore the drain pump should be cleaned at least once a year Warning Switch off the washing machine and pull out t
40. t to do if si ee beca uei a 30 Remedying Faults ascen a an ni 30 If the washing results are not satisfactory 0 00 een 34 Carrying out emergency drainage ii 35 Additional Rinse 7 RINSE4 2 2 2222 22 36 Child Safety Feature ii 37 Installation and connection instructions 38 Installation Safety Precautions ik 38 Installation of the appliance ii 39 Transporting the appliance ii 39 Remove transportation protection 0 cece eee eee eee 39 Prepare the installation place 2 eee 41 Installation on a concrete base aa 41 Installation on vibrating floors nenn 41 Compensate for floor unevenness ii 42 Contents Electrical connection nanah 43 Water connection ii 43 Permissible water pressure ii 43 Water inflow nan 44 Water ral Anna eni meta Era ee TA ae ROM dan 45 Delivery heads over 1m ii 46 Technical data c ree na ena 46 Dimensions apex RA rn TE RIP 46 Warranty conditions Customer service centres 47 diio ea 50 Operating Instructions Operating Instructions AN Safety The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law However as manufacturers we regard it as our responsibility to inform
41. ts They are not the result of an insufficient rinsing effect Shake or brush out the washing In future perhaps you should turn the washing inside out before washing it Examine your choice of de tergent and if necessary use liquid detergent Operating Instructions Carrying out emergency drainage I 1 Fold open the flap in the right section Remove the emergency drainage hose Place the container under the hose Detach the plug of the emergency e If the washing machine no longer pumps off the washing solution emergency drainage must be performed e f the washing machine is in a room where there is a risk of frost emergency drainage must be performed if there is a possibility of frost In addition unscrew the inlet hose form the water tap and place it on the floor Empty the drainage hose Warning Switch off the washing machine before performing emer gency drainage and pull out the mains plug Caution The washing solution escaping from the emergency drainage hose may be hot There is a risk of scalding Allow the washing solution to cool down before performing emergency drainage Place a flat collecting vessel in order to collect the washing solution which is draining off of the base outwards and pull it off from its holder drainage hose by turning it anticlock wise and pull it out The washing solution runs out Depend ing on the amount of solution it may be necess
42. ut 1 litre of water through the washing powder drawer into the washing machine With the next program start this will close the solution container and the eco sluice can function correctly 3 Run the washing cycle without washing kw COTTONS LINEN 95 C with half the amount of washing detergent This removes residues left over from production on the drum and solution container Operating Instructions Prepare washing cycle Sort washing and prepare e Sort the washing according to the care symbol and type see Wash ing types and care codes Empty all pockets Remove metal objects paper clips safety pins etc To prevent damage to the washing and tangled washing Close zip fasteners button bed and pillow covers closed tie up loose strings e g of aprons Turn articles with double layered textiles inside out sleeping bags anoraks etc e n the case of knitted coloured textiles and also with wool and tex tiles with jewelry attached turn inside out e Wash small and sensitive items e g baby socks tights and stockings bras etc in a washing net a cushion with a zip fastener or in larger socks Handle curtains with particular care Metal rollers or burred plastic rollers must be removed or tied into a net or bag We cannot accept liability for damage Coloureds and white items must not be washed together in a washing cycle This could discolour white washing or turn it grey e There is oft
43. witch off the circuit breaker at the household power distribution box or completely remove the screw in fuse Never pull the cable to remove the plug from the socket Always pull the plug itself Multiple connectors couplings and extension cables must not be used There is a risk of fire with overheating Do not spray down the washing machine with a water jet Risk of electric shock e The glass in the door becomes hot in the case of wash programmes with high temperatures Do not touch Allow the washing solution to cool before carrying out an emergency emptying operation or cleaning the drain pump Small animals can chew the power cables and water hoses Risk of electric shock and danger of water damage Keep small animals away from the washing machine Operating Instructions Disposal Disposing of the Packaging Material Dispose of the packaging of your washing machine correctly All pakka ging materials used are environmentally compatible and recyclable Plastic parts are identified with internationally standardised abbrevi ations gt PE lt for polyethylene e g packing films gt PS lt for polystyrene e g cushion parts always CFC free gt POM lt for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposing of your old appliance When you put your unit out of operation one day pl
Download Pdf Manuals
Related Search