ACTiSYS ACT-IR100S Network Card User Manual
Contents
1. I IrDA operation mode configuration R11 R12 00 Reserver 10 primary channel 01 secondary channel 11 primary secondary 2 Item 1 IrDA Operational Mode Settings It is possible to select the primary channel mode secondary channel mode and the primary channel as well as the secondary channel according to the settings of R11 and R12 Operation mode mode setting terminal Reservation on o primary channel JL or secondary channel oR Primary secondary channel Po Item 2 RS 232C Communication Speed Settings It is possible to set the RS 232C communication speed with R13 R14 and R15 However when the control line extension mode of R16 is not installed the settings will be valid for all self channels But when it is OR if the R11 and R12 s IrDA mode setting is primary or primary secondary channel then the self channel with be valid If it is set to the secondary channel regardless of the communication speed setting the other device will set the communication speed Figure 2 2 When the communication rate has established an IrDA link it will be sampled so it is okay to change the speed settings while it is in operation In the event that the speed is changed while communicating the current communication link will be severed and with any following communication the new speed will become valid Figure 2 1 Communication Speed Communication Speed Setting Te2. OTHER ACTiSYS IrDA PRODUCTS ACA ACT 1 IrDA Primary Station Protocol Stack IrLAP IrLMP IAS and optional Tiny TP IICOMM IrMC IrTran P etc For PDA digital camera handheld data terminal palmtop computer smart phone Very tight code modular design easy porting and API interface well supported Small code size 20 40K bytes well tested and inter operate with all IrDA devices ACE II ACT 2 IrDA Secondary Station Protocol Stack IrLAP IrLMP IAS and optional Tiny TP IICOMM IrMC IrTran P etc For printer pager docking station medical device cell phone storage devices Very tight code modular design easy porting and API interface well supported Small code size 4 20K bytes well tested and inter operate with all IrDA devices ACTUA 100m IrDA Printer Adapter Attached to and works well with any parallel printers IR wireless printing directly from your IrDA devices Automatic switch between mobile IR and desktop cable based printing LED indicate transmission speed and printing status SACC 220 1 IrDA Com Port Serial Adapter Connects to the serial port on any computer No power needed e Data transfer wirelessly from IrDA mobile devices e Model already built into Windows 95 98 2000 IR driver e IR distance from Ocm 200cm with no external power ACE 2000U FIR USB Adapter Plugs into any desktop PC USB port Gives you the full IrDA speeds from 9 6K to 4M bps Meets both USB 1 1 an
3. Transmissible Indicates that the modem is able to transmit When CS is ON the modem is able to receive Example Connection Reference 2 PC Terminal DTE Connection IR100S I F lt Cross Cable gt PC Terminal DTE RxD RxD Data Receiving RD RD Only valid with received data when the DCD CD signal is on TxD TxD Data Transmission SD SD Valid with sending data when RTS RS CTS CS DSR DR DTR ER are on DTR DTR Data Terminal Ready ER ER Turns ON when the device is able to send and receive DSR DSR Data Set Ready DR DR Turns ON when the device is able to send and receive RTS RTS Transmission Request RS RS Instructs the device to be in transmission mode The terminal is turned on before transmission ICTS CTS Transmissible CS CS Indicates that the device is able to transmit When CS is ON the device is able to receive GENERAL SPECIFICATION Product Name ACT IR100S Compatibility Fully compatible with IrDA 1 0 Physical spec and IrDA 1 0 protocol spec IrLAP IrLMP IAS TinyTp IICOMM Specifications of IrDA 1 0 SIR Transmission Speed 9 6kbps 19 2kbps 38 4kbps 57 6kbps 115 2kbps Communication within 100cm Distance Radiating Angle 15 30 15 to 30 degrees Peak Wave Length of 880 1050nm Radiated Light Specifications of RS 232 port Transmission Speed 9 6kbps 19 2kbps 38 4kbps 57 6kbps 115 2kbps Cable Length 110 120 cm Connecto
4. ACTIS YS ACT IR100S Intelligent IrDA Serial Adapter User s Manual ACTISYS Corp 48511 Warm Springs Blvd Suite 206 Fremont CA 94539 USA Tel 510 490 8024 Fax 510 623 7268 E Mail irda support actisys com Rev 1 10 Web www actisys com March 14 2000 FCC amp VCCI Compliance Statement This device complies with part 15 ofthe FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation WARNING FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user authority to operate this equipment NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to Part 15 of the FCC Rules This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will nor occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Increase the sepa
5. Monitor you will see the Status are 11 Communicating with Name ACTiSYS IR100S 115 Nickname of 100s might be different with different version Description Intelligent SIR Adapter Communication efficiency Good at 115 2 Kbps or 57 6 Kbps Depends on the highest speed both sides can support Run HyperTerminal on PC 1 now Set its properties according to the above configuration guide Click the Call icon to connect to the assigned IR port The LED DSR and CTS of the RS232 Mini Tester on PC 2 side should turn to Red True when it is connected and the 100S LED will blink once every half second Type keys on PC 1 s keyboard and you should see the results will display on the remote HyperTerminal s screen If you have got strange letters the baud rate you set for the HyperTerminal is not the same as 100s File Transfer Click the menu Transfer and Receive File on PC Click the menu Transfer and Send File on PC 2 Fig A 5 The operation is similar to use cable connection The real data transfer speed depends on the lower one of IR speed and RS 232 speed For example the IR Speed is limited to 57 6kbps and the RS 232 speed of 100s is 9600 the effective speed throughput is 9570bps Fig A 6 If the RS 232 speed set to 115 2kbps The throughput would be around 5kbytes Sec Oe play he prag BIRI SIE cu meni PERI EO Figure A 2 12 Figure A 3 Figure A 4 Del gil cola re Figure A 5 IK EGE ERIZE F
6. are For Portable Devices A H IrDA Test Software For Hardware Systems d H IrDA Printer And Computer Adapters ISK 4M and IGM bps N IR100M 1000M ACTISYS Corporation Member ERW ed amp 96 Y Mll e 2 22
7. cator Electricity source a With Voltage Regulator UG is placed R25 is removed AC Adaptor DC 7 5V 300mA above e DC 5V Gnd seconds O 1 6 O O 2 7 0 O 3 8 O O 14 9 O O 5 b Without Voltage Regulator U6_ is removed R25 is placed DC 5V 450mA above stable source Part 4 How to connect Q Serial Port When connecting modems etc to the Data Communication Equipment DCE side connect the corresponding signal names of the modem and IR100S When connecting to PC s to the Data Terminal Equipment DTE side use a cross connection for IR100S and the PC or Plotter Printer with RS232 port Example Connection Reference 1 Modem DCE Connection IR100S I F RxD RD TxD SD DTR ER DSR DR RTS RS CTS CS lt Straight Cable gt 4 amp bb RD AAA SD TR CER a DSR DR PRTS RS lt 4 ETS CS Modem DCE Data Receiving Only valid with received data when the DCD CD signal is on Data Transmission Valid with sending data when RTS RS CTS CS DSR DR DTR ER are on Data Terminal Ready Turns on when receiving and transmitting of data is possible and when the terminal has power Data set ready Turns ON when the modem is able to send and receive Transmission Request Instructs the modem to be in transmission mode The terminal is turned on before the transmission
8. d IrDA 1 1 specification Bundled with drivers for Windows 98 and Windows 2000 USB bus powered requires no external power supply me CE ee PE Fe UNIVERSAL SERIAL BUS LETI 20 THE FOLLOWING WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE LIMITED WARRANTY ACTISYS Corporation warrants to the first consumer purchaser for a period of 1 year from the date of purchase that this wireless interface The Product Will be free from defective workmanship and materials and agrees that it will at its option either repair the defect or replace the defective Product or part thereof at no charge to the purchaser for parts or for labor This warranty does not apply to any appearance items of the Product any consumable items such as paper ink ribbon or batteries supplied with the Product orto any equipment or any hardware software firmware or peripheral other than the Product This warranty does not apply to any Product the exterior of which has been damaged or defected which has been subjected to misuse abnormal service or handling or which has been altered or modified in design construction or interfacing Tampering With Label Voids Warranty In order to enforce the rights under this limited warranty the purchaser should mail ship or carry the Product together with proof of purchase to ACTISYS The limited warranty described above is in addition to w
9. er Option DC Power Supply 5V stable source or 7 5V adapter for regulator installed SW WIN95 98 HyperTerminal 10 IR2000B WIN95 98 WIN95 98 HyperTerminal IrDA HyperTerminal IR Monitor COMI 2 IR2000L IR220L IR100S DTE DTE DCE Converter RS 232 Mini Figure A 1 IR100S System Configuration Tester 3 Configurations PC 1 Install IrDA Driver The assigned IR virtual port must be COMA or less otherwise HyperTerminal will not be able to connect it IR Monitor Speed limit 115 2K or lower HyperTerminal Connect Using gt direct to COM4 assigned virtual port of IR PCH2 1008 R11 18 or DSW8 1 1100 0111 Primary Secondary 9 6k Self channel setting 8 N HyperTerminal Connect Using gt direct to COM1 or COM2 the port IR100S using 9 6k 8 n 1 Hardware flow control 4 Test Procedure 1 Connect all devices as FigA 1 2 Switch on PC 2 and the power supply of 100s 3 Run HyperTerminal on PC 2 Set its properties according to the above configuration guide Fig A 2 4 The LED DTR and RTS of the RS232 Mini Tester should be Red True when it is connected The DTR will go to Green False if you disconnect it When both DTR and RTS are True high level the 1008 will begin discovery if you set it to Primary or Primary Secondary The 100S LED will blink once every 3 seconds 4 Switch on PC 1 You will see the IR Found icon and hear the sound of found IR device when windows has started Open the IR
10. hatever implied warranties may be granted to purchasers by law To the extent permitted by applicable law ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANT ABILITY AND FITNESS FOR USE ARE LIMITED TO APERIOD OF 1 YEAR FROM THE DATE OF PURCHASE Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described above or to extend the duration of any warranties beyond the time period described above on behalf of ACTISYS Corporation The warranties described above shall be the sole and exclusive remedy available to the purchaser Correction of defects in the manner and for the period of time described above shall constitute full satisfaction of all claims whether based on contract negligence strict liability or otherwise In no event shall ACTISYS Corporation be liable or in any way responsible for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than ACTISYS technician Nor shall ACTISYS Corporation be liable or in any way responsible for any incidental or consequential economic or property damage Some states do not allow the exclusion of incidental or consequential damages so the above exclusion may not apply to you 21 TZ 4 The Wireless Infra red Expert IrDA Protocol Softw
11. igure A 6 APPENDIX B Using IR100S to convert a normal Modem into a wireless IrDA Modem 1 Working Principle If your device has no built in modem and wants to connect to Internet normally you will buy an external modem and use cable to connect them together But some mobile devices are so small that have no RS 232 port for cable connection Most of them have IrDA wireless built in interface so that they can connect with an IrDA modem without cable One usage of ACT IR 100S is to make those normal modem into IrDA compatible product by simply connecting it to their serial port And these devices with IR100S COM IrDA bridge can communicate with PC or your IrDA cable devices wirelessly and don t need to modify neither hardware nor software This simply test uses one PC with IrDA adapter with driver installed and an external modem connected with IR100S On PC uses Make New Connection wizard of Dial Up Networking to create a new dial up connection to your ISP through the IR modem It should be able to find the modem dial phone number establish a connection to internet and browse the web 2 Hardware and Software Requirements PC HW x386 or better PC ACTISYS IR2000B board based on NS87108A with IR2000L dongle or ACT IR220L Com port Adapter connected to COM1 or COM2 SW WIN95 98 IrDA Driver for SIR if using IR220L or FIR if using IR2000B Dial Up Networking IR Monitor75 External Modem IR100S RS232 Mini Tester Option DC Po
12. its can be damaged by a static electricity discharge If this device requires any servicing use only an ACTiSYS service dealer an ACTiSYS approved service facility or an ACTISYS repair service When exchanging data with host computer be sure the appropriate serial communication port is available and is not in conflict with other peripheral device or software OPERATION SETTINGS Part 1 Functional mode Settings R11 R18 Here the settings for the R11 R18 are displayed When power is thrown for any resistor besides R13 R15 they will be sampled at the time NMI is reinstated After that there will be no problems with operation even if the settings are changed however the settings will become invalid e R11 R18 1 None 0 Install 0 R 0603 o oo PCB bottom view S 8 R11 R12 R13 R14 R15 R16 R17 R18 Rilnitial Setting Data Length R18 1 8 bit x 0 7 bit 0000000008 Parity R17 1 None d O Even Control Line Extension Mode R16 Condition for starting discovery Serial Settings primary channel bps data length parity Condition for permission to Connect secondary channel 1 Self channel R13 R15 When DSR ON CTS ON x Settings O Settings from partner channel RS 232C Communication Speed Setting R13 R14 R15 000 9600 bps 100 19200 bps 010 38400 bps 110 57600 bps 001 115200 bps gt
13. r ea 6 Part 4 How to galaia d 7 GENERAL SPEGIFICATION u aa E Ea 9 APPENDIX A ACTiSYS IR100S Testing Demonstration Procedure 10 APPENDIX B Using IR100S to Convert a Modem to a wireless IrDA Modem 15 OTHER ACTISYS IrDA PRODUCTS earra E ae Ekartea 20 LIMITED WARRANTY cecinit xe HEHE 21 PRECAUTIONS To ensure trouble free operation please observe the following precautions Optical communications are easily affected by external light sources weak batteries transfer distance transfer angle etc Any of these conditions may cause a data transfer failure incomplete missing or incorrect data Make sure that the wireless interface is away from direct sunlight and other strong light source Do not terminate arbitrarily during file transfer process between DUT and computers until finished Otherwise DUT internal data integrity may be damaged which is due to the violation of DUT s Do not expose the unit to moisture as this will damage the internal circuitry Do not expose the unit to extreme temperatures It should not be placed in direct sunlight or in a closed vehicle neither should it be placed near heaters nor other heat sources Do not store the unit in a humid or dusty place Use a soft dry cloth to clean the unit Do not use a wet cloth or any solvent Do not drop the unit or handle the unit carelessly CAUTION Never touch the pins of computer connection terminal The internal circu
14. r DB 9M DTE or DB F DCE Signal Definition DTE or DCE Power Source 5 VDC Stable or 7 5 VDC AC adapter Power Consumption Active 80mA Dimensions 61mmL x 35mmW x 18mmH 2 4 L x 1 4 W x 0 7 H Weight 65 gr 2 5 Oz Operating Temperature 0 C TO 60 C Storage Temperature 20 C TO 85 C APPENDIX A ACTiSYS IR100S TESTING DEMONSTRATION PROCEDURE 1 Working Principle Many PC peripherals use serial cable to communicate with PC They cannot talk with Infrared Devices such as IrDA capable PC notebooks ACT IR 100S s aim is to make those devices into IrDA compatible product by simply connecting it to their serial port And these devices with IR100S COM port IrDA bridge can communicate with PC wirelessly and don t need to modify neither hardware nor software This simply test uses two PCs one is IrDA installed and another is not Both Run Windows HyperTerminal Program one of the communication accessories You should be able to type on one keyboard and see results on another PC s screen or transfer files between them through the infrared connection 2 Hardware and Software Requirements PC 1 HW x386 or better PC ACTiSYS IR2000B board based on NS87108A with IR2000L dongle or ACT IR220L Com port Adapter connected to COM1 or COM2 SW WIN95 98 IrDA Driver for SIR if using IR220L or FIR if using IR2000B HyperTerminal IR Monitor PC 2 HW x386 or better PC ACT IR100S DTE DCE Converter RS232 Mini Test
15. ration between the equipment and receiver Reorient or relocate the receiving antenna Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This equipment is in the 2nd Class category information equipment to be used in a residential area there to and conforms to the standards set by the Voluntary Control Council For Interference by Data Processing Equipment and Electronic Office Machines aimed at preventing radio interference in such residential area When used near a radio or TV receiver it may become the cause of radio interference Read the instructions for correct handling NOTE Must be used with shielded cable only FOR YOU RECORDS For your assistance in reporting this product in case of loss or theft please record below the model number and serial which are located on the bottom of the case Please retain this information Place of Purchase All indicated copyrights and trademarks in the following pages are copyrights and trademarks of their Respective corporations TABLE OF CONTENTS PRECAUTIONS u nl 3 Operation d e EEE 4 Part 1 Function mode Settings R11 R18 4 Item 1 IrDA Operation Mode Settings ccccccccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 5 Item 2 RS 232C Communication Speed SGetttngs aaa 5 Part 2 LED Indicator Function 6 Part 3 Conneelo
16. rminal ooops op oR on JES o o mops o o 870bps o See OR o Figure 2 2 R16 Primary Channel Secondary Channel Primary Secondary Channel R12 0R R11 R12 R11 0R R12 R11 self channel self channel self channel OR self channel other channel self channel Part 2 LED Indicator Function In order to confirm that the device is operating correctly there is an indicate function installed By looking at the flash of the LED you can check the state of communication There are 2 flashing speeds during standby on the secondary channel there is no flashing Ifthe primary channel commences discovery it will flash once every 3 seconds for approx 0 7 seconds After discovering the other device and communication becomes possible it will flash every 0 4 seconds Operating condition LED during connection standby Low flashing once every 3 seconds during discovery during communication with other device Part 3 Connector D sub 9 pin Male connector RS 232C flashing flashing low speed high speed for approx 0 7 seconds switches from High to Low every 0 4 Descriptions 1 DCD Data Carrier Detect 2 RxD Receiver Data 3 TxD Transmitter Data O 4 DTR Data Terminal Ready O 5 GND Signal Ground Gnd 6 DSR Data Set Ready 7 RTS Request to Send O 8 CTS Clear to Send 9 RI Ring Indi
17. wer Supply 5V stable source or 7 5V adapter for regulator installed 15 IR2000B WIN95 98 IrDA Dial Up Networking IR Monitor IR2000L IR220L IR100S DTE DC 5V 7 5V Figure B 1 IR100S Modem System Configuration 3 Configurations Connect all devices as Fig B 1 PC Install IrDA Driver Configure the Modem Fig B 2 6 Port Virtual Infrared COM Port Maximum Speed 115 2 Kbps Data bits Parity Stop bits 8 N 1 Use flow control Hardware RTS CTS 100S R11 18 or DSW8 1 1100 0111 Primary Secondary 9 6k Self channel setting 8 N 4 Establish a Connection Switch on modem and the power supply of 100s The CTS and DSR LED on the Mini RS 232 Tester should change color from Green False to Red True Put the two IR dongles face to face Start up PC Win95 98 and the program IR Monitor should find IR100S device Fig B 8 You will see the IR Found icon and hear the sound of found IR device Run Dial up network connection on PC Set its properties according to the upper configuration guide Fig B 2 6 If a connection is established DTR and RTS are turned ON Red True Open the IR Monitor you will see the Connection Status Fig B 10 Start the connect procedure you will see phone dialing and negotiations Fig B 9 16 me EE AA Make New ACTISYS Connection Figure B 2 Figure B 4 Figure B 5 17 Figure B 7 Figure B 8 18 Figure B 9 Figure B 10 19
Download Pdf Manuals
Related Search