Accton Technology EN1207D-TX Network Card User Manual
Contents
1. IRQ number Check the BIOS Setup program s PCI parameters for the slot where the Cheetah PCI Adapter is installed Be sure the slot is configured for level triggered interrupts instead of edge triggered interrupts An example of typical PCI parameters follows PCI Slot slot number where the network card is installed Master Enabled Slave Enabled Latency Timer 40 range is 20 to 255 Interrupt Type Level Triggered Interrupt Number choose any number the BIOS Setup supplies that does not conflict with another installed card Note The wording of these parameters varies with different computers and not all parameters may be configurable Always consult your computer manual for information on changing motherboard jumper settings and BIOS Setup program parameters for use with PCI network cards If you set a motherboard jumper and modify the computer s BIOS Setup make sure the jumper and BIOS settings match Cheetah PCI Adapter Adapter Installation Problems If your computer can t find the Cheetah PCI Adapter or the network driver doesn t install correctly check the following Make sure the adapter is securely seated in the PCI slot Check for any hardware problems such as physical damage to the card s edge connector Try the card in another PCI bus master slot If all fails test with another Cheetah PCI Adapter that is known to operate correctly Check for resource conflict in the PCI configuration Se2. Accton Making Partnership Work Cheetah PCI Adapter Quick Installation Guide Cheetah PCI Adapter Introduction Accton s Cheetah PCI Adapter is a dual speed Fast Ethernet card for PCI local bus compliant computers A true plug and play device this card is auto configurable upon power up and also supports auto negotiation to automatically select the optimum speed and communication mode of an attached device Additionally the Cheetah PCI Adapter complies with ACPI Wired for Management 2 0 and PC99 and includes support for Remote Wake Up by Magic Packet Package Checklist Accton s Cheetah PCI Adapter includes e 1 Cheetah PCI Adapter EN1207D TX 1 driver diskette e 1 registration card please return This Quick Installation Guide Immediately inform your dealer in the event of any incorrect missing or damaged parts If possible please retain the carton and original packing materials in case there is a need to return the product Note that new or updated driver information is available via Accton s Web site Please fill out and return the registration card to Accton The Cheetah PCI Adapter is covered by a limited lifetime warranty Hardware Description The Cheetah PCI Adapter is equipped with 1 10BASE T 100BASE TX RJ 45 port e 3 LED indicators The components of the Cheetah PCI Adapter are shown in the figure below LED Indicators RJ 45 Connector for 10 100 Mbps
3. NOR AUTHORIZES ANY PERSON TO ASSUME FOR ITANY OTHER LIABILITY Copyright Copyright 1999 by Accton Technology Corporation All rights reserved No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Accton Technology Corporation Trademarks Accton is a trademark of Accton Technology Corporation Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies Disclaimer Accton makes no warranties with respect to this documentation and disclaims any implied warranties of merchantability quality or fitness for any particular purpose The information in this document is subject to change without notice Accton reserves the right to make revisions to this publication without obligation to notify any person or entity of any such changes Accton International Headquarters USA Headquarters No 1 Creation Road Ill 6 Hughes Science based Industrial Park Irvine CA 92618 Hsinchu 300 Taiwan R O C Phone Numbers Phone 886 3 5770 270 Sales 800 926 9288 FAX 886 3 5770 267 Support 888 398 4101 949 707 4847 Internet support accton com tw RMA 800 762 4968 FAX 949 707 2460 EN1207D TX E1199 R01
4. TCeEMHV ST Erre zeaSI Cito TEU RV RN ELTTFSEL CE Mark Declaration of Conformance This is to certify that this product complies with ISO IEC Guide 22 and EN45014 It conforms to the following specifications EMC EN55022 1988 CISPR 22 1985 class B IEC 1000 4 2 1995 4kV CD 8kV AD IEC 1000 4 3 1995 3V m IEC 1000 4 4 1995 1kV power line IEC 1000 4 6 1995 3Vrms This product complies with the requirements of the Low Voltage Directive 73 23 EEC and the EMC Directive 89 336 EEC and carries the CE Mark accordingly Quick Installation Guide Specifications General Specifications Network Interface Data Interface 1 0 Address Interrupt LED Indicators Temperature Humidity Power Consumption Size without bracket Weight Standards Supported EMC Safety Compliances CE Mark Emmisions Software Drivers Microsoft drivers Novell NetWare Unix Other 10 10BASE T RJ 45 UTP Cable Categories 3 4 5 100BASE TX RJ 45 UTP Cable Category 5 32 bit bus mastering PCI Automatically determined by configuration space INT A mapping to BIOS IRQ setup 10 Mbps Link 100 Mbps Link Activity 0 to 55 C 32 to 131 F operating 10 to 65 C 14 to 149 F storage 10 to 90 non condensing 5 VDC 210 mA maximum 119 92 x 56 03 mm 4 72 x 2 21 in 56 g 1 98 oz IEEE 802 3 802 3u PCI bus V2 2 PCI Power Management Specification 1 1 ACPI 1 0b no D3 Cold support WfM 2 0 Microsof
5. contact Accton s Technical Support for assistance SET120 Accton EN1207D TX Adapter SetUp And Diagnostics Program Main Menu Previous Esc Select TL Accept J Quick Installation Guide Troubleshooting Check the following troubleshooting items before contacting Accton Technical Support PCI Compatibility Some PCI computers are not self configuring and require you to perform some or all of the following functions by motherboard jumper changes and or BIOS Setup program configuration Make sure your BIOS correctly supports the PCI Local Bus Specification v2 0 or later and upgrade your computer BIOS to the latest version e Verify that the PCI slot is an enabled bus master slot and not a slave PCI slot In some computers the PCI slot must be configured to enable bus mastering Refer to your PC s manual and check the PCI BIOS Setup program to be sure the PCI slot is an enabled bus master slot e In some computers you may be required to disable Plug n Play PnP in the BIOS Setup program if resources are not properly assigned between installed cards Some computers may require you to reserve interrupts and memory addresses for installed ISA cards to prevent PCI cards from using the same settings Refer to your PC s manual and check the PCI BIOS Setup program configuration options for ISA cards Make sure the PCI slot is configured to support INTA e Be sure that INTA for the slot is assigned to a free interrupt
6. d configured the service correctly If you cannot connect to a particular server be sure that you have access rights and a valid ID and password If you cannot access the Internet be sure you have configured your system for TCP IP Quick Installation Guide Compliances FCC Class B Certification This device complies with Part 15 of the FCC Rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the distance between the equipment and r
7. e PCI Compatibility e Make sure your computer is using the latest BIOS available e If there are other network adapters in the computer they may be causing conflict Remove all other adapters from the computer and test the Accton adapter separately Check for a defective computer or PCI bus by trying the adapter in another computer that is known to operate correctly Network Connection Problems If the Link LED on the adapter s bracket does not light or if you can t access any network resources from the computer Check the following Be sure you are using Category 5 cable for 100Mbps connections and that the length of any cable does not exceed 100m 328ft e Inspect all network cables and connections Make sure the cable is securely attached to the adapter s connector Make sure the correct software driver is installed for your operating system If necessary try reinstalling the driver Make sure the computer and other network devices are receiving power e If the adapter s speed or duplex mode has been configured manually check that it matches that of the attached network device port Note that it is recommended to set the adapter to auto negotiation when installing the network driver e The port on the network device that the adapter is attached to may be defective Try using another port on the device e If you cannot access a Windows or NetWare service on the network check that you have enabled an
8. eceiver e Connect the equipment into an outlet on a circuit different from the one which the receiver is connected to Consult the dealer or an experienced radio TV technician for help You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment Attach shielded or unshielded Category 3 4 or 5 twisted pair cable to the RJ 45 port Note In order to maintain compliance with the limits of a Class B digital device Accton requires that you use a quality interface cable when connecting to this device Changes or modifications not expressly approved by Accton could void the users authority to operate this equipment Suggested cable type is 1002 shielded or unshielded Category 3 4 or 5 twisted pair cable for the RJ 45 port CSA Statement Canada This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of Industry Canada Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils numerigues de la classe B prescrites dens le Reglement sur le brouillage radio lectrique dict par l Industrie Cheetah PCI Adapter VCCI Class B Compliance Japan CORE IIS RIESI ME VCC OB TES OS AB MERE CI CORES KERATAN SBMELTHETH CORBMSVAPFLEY a LEMARI uk EL T EFRThat SECS SRO
9. een will display the Main Menu see below Quick Installation Guide SET1207D Accton EN1207D TX Adapter SetUp And Diagnostics Program View Current Configuration Set Up New Configuration Run Diagnostics Exit Program Choose VIEW CURRENT CONFIGURATION to look at the current PCI LAN board configuration Select TL 2 Select the View Current Configuration option from the Main Menu to access the screen shown below If you wish to modify the current configuration return to the Main Menu and select Setup New Configuration SET1207D Accton EN1207D TX Adapter SetUp And Diagnostics Program Press Space Bar to Continue 3 The host computer s BIOS automatically allocates the necessary resources such as the Interrupt and I O Base to the Cheetah PCI Adapter Although the Setup Program will not allow you to change those resources you can change the settings displayed on the Setup New Configuration screen see below Cheetah PCI Adapter SET12 ccton EN1207D TX Adapter SetUp And Diagnostics Program orce mode function Help FI Previous Esc In the event of a problem with the Cheetah PCI Adapter use the Setup Program to run the card s built in diagnostics see the SET1207D TXT file for specific instructions Should any of the diagnostic tests fail reboot your computer and run the diagnostics again to see if the problem persists If it does record the failure indicated and
10. g Quick Installation Guide 100 Mbps Link Activity LED Indicators The following table describes the operation of the Cheetah PCI Adapter status LEDs 100 10 O O 10 Mbps Link ACT LNK Ru 45 O VU LED Status Description LNK 10 Mbps Green Valid 10BASE T link Off Power is off 1OBASE T connection is invalid 100 Mbps Green Valid 100BASE TX link Off Power is off 100BASE TX connection is invalid ACT Green Heavy network activity Blinking Intermittent or light network activity the blinking rate is proportional to the amount of network traffic Installation Warnings Network cards are sensitive to static electricity To protect the card avoid touching its electrical components and always touch the metal chassis of your computer before handling the card Backup your driver diskette and use the copy as the working diskette to protect the original from accidental damage 1 Switch off the computer unplug the power cord and remove the computer s cover 2 Select an unused PCI bus master slot and remove its protective bracket 3 Carefully insert the card and press until all the edge connectors are firmly seated inside the slot Then screw the card s bracket securely into the PC s chassis Cheetah PCI Adapter 4 Connect the Cheetah PCI Adapter directly to a 10BASE T or 100BASE TX hub or switch using UTP cable Category 3 4 o
11. r 5 for 10BASE T Category 5 for 100BASE TX The maximum allowable length of UTP cable connections is 100 meters 328 ft When inserting an RJ 45 plug be sure the tab on the plug clicks into position to ensure that it is properly seated 5 Replace the computer s cover and power it on The Cheetah PCI Adapter should be automatically configured by the host computer s BIOS However if you have an older computer you may have to manually configure the computer s BIOS settings See Troubleshooting 6 Install the appropriate network driver for your operating system The Accton driver diskette that accompanies the Cheetah PCI Adapter contains all the network operating system drivers supported by this card For convenience the Windows 95 98 and Windows NT drivers are placed in the diskette s root directory Please read the RELEASE TXT file on the diskette for a list of all drivers A text file is included with each driver to detail the proper installation procedure Any new or updated drivers can be downloaded from Accton s Web site at http www accton com Setup Program If the Cheetah PCI Adapter is not automatically configured by the host PC or there is a problem with the card run the DOS based Setup Program to help configure the PC s BIOS settings and test the card 1 Boot the computer to a full DOS environment not a DOS window and run the Setup Program SET1207D EXE on the Accton driver diskette The scr
12. t On Now PC99 Magic Packet EN50081 1 EN55022 1EC1000 4 2 3 4 6 FCC Class B VCCI Class B Industry Canada Class B EN55022 CISPR 22 Class B Windows 95 98 Windows NT 3 51 4 0 Windows 2000 Windows for Workgroups 3 11 LAN Manager v1 x 2 x NetWare 3 1x 4 x 5 0 32 bit ODI Driver 16 bit DOS ODI Driver Client32 for Windows 95 SCO Unix 5 0x SCO Unixware 7 x Linux FreeBSD NDIS2 DOS Mode Driver Packet Driver Cheetah PCI Adapter 11 Warranty Accton warrants to the original owner that the product delivered in this package will be free from defects in material and workmanship for the lifetime of the product For the warranty to apply you must register your purchase by returning the registration card indicating the date of purchase and including proof of purchase There will be a minimal charge to replace consumable components such as fuses power transformers and mechanical cooling devices The warranty does not cover the product if it is damaged in the process of being installed Accton recommends that you have the company from whom you purchased this product install it THE ABOVE WARRANTY IS IN LIEU OF ANY OTHER WARRANTY WHETHER EXPRESS IMPLIED OR STATUTORY INCLUDING BUT NOT LIMITED TO ANY WARRANTY OF MERCHANTABLLITY FITNESS FORA PARTICULAR PURPOSE OR ANY WARRANTY ARISING OUT OF ANY PROPOSAL SPECIFICATION OR SAMPLE ACCTON SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ACCTON NEITHER ASSUMES
Download Pdf Manuals
Related Search