Vicon CE202D-WN Installation guide
Contents
1. e Connecting the Power Connect a 12 VDC power adaptor customer supplied to the camera e Connecting Service Monitor Port The Service Monitor output port is located on the board of the dome camera and is used for easy OSD setup gt ID amp IP assignment To make changes in the OSD menu the optional V920D OSD controller can be used to set camera title and IP address Connect the OSD Controller to the Service Monitor port of the network camera Connect Service Monitor and the Video Output port of the OSD Controller Press the SET button on the controller to access the Main Menu Change camera ID and IP address as needed Additionally the Name or title of the camera can be changed Use the T buttons on the controller to change the parameters 5 Select SAVE or CANCEL to exit the Main Menu A PAE Fa INFORMATION 001 NAME CE202D WN NETWORK 192 163 30 220 k SAVE CANCEL The Video Output can also be used for easy zoom and focus control when adjusting the lens Video Output is restricted to 704x480 576 resolution gt Pan amp Tilt Control The camera enters Zoom and Focus control mode when the OSD Controller is connected to the Service Monitor port Pan Control T Up Down Tilt Control Left Right Note The optional V920D OSD OSD Controller can be purchased separately 2 3 Network Connection and IP assignment The network camera is designed for use on an Ethernet2. described in 3 5 6 System gt Maintenance or use the Reset button on the network camera as described below Reset Button FDFLT rele a O s On Board e Using the Reset Button Follow the instructions below to reset the Network Camera to the factory default settings using the Reset button O e N e a 6 Power off the network camera by disconnecting the power adapter Remove lower dome if not already done so Press and hold the Reset button with a straightened paperclip while reconnecting the power Keep the Reset button pressed for about 2 seconds Release the Reset button The network camera resets to factory defaults and restarts after completing the factory reset The unit now obtains the IP address automatically via DHCP Reattach the dome 3 7 More Information For more information refer to the network camera User s manual which is available on the CD included in this package 12 Vicon Industries Inc Internet Address www vicon security com AVA TAJ VICON CE202D WN 50303720 Rev A
3. IP Address zen Coni IP Version um All Devices 1 ee 5 10 rele ca CE202D WNPT 1 i Remote Setup O ONVIF 1 Quick View Es Group td Assign IP Maintenance Log In i Open Web Page Emergency Firmware Upgrade Ready NUM 4 Select Assign IP The on IP window displays Enter the required IP address Assign IP Address Assign new IP address Camera Information Model CEZ02Z0 WHPT Name H 264 Mini PT Dome MAC Address 00 07 D8 00 F1 FS Note For more information refer to the Smart Manger User s IP Address 192 169 30 221 Manual 3 Cancel 3 Operation The network camera can be used with Windows operating system and browsers The recommended browsers are Internet Explorer Safari Firefox Opera and Google Chrome with Windows Note To view streaming video in Microsoft Internet Explorer set your browser to allow ActiveX controls Note Some screens may appear different i e color scheme depending on the firmware version but the functionality is the same or similar 3 1 Access from a browser 1 Start a browser i e Internet Explorer 2 Enter the IP address or host name of the network camera in the Location Address field of your browser 3 A starting page displays Click Live View Playback or Setup to enter web page H 264 Mini PT Dome Ol Live View Playback 4 Click Live View for the network camera s Live View page to appear in the browser Q
4. Tilt Click the navigation button in the PT control panel Pan Control gt Right lt Left Tilt Control 4 Up Y Down 3 5 Network Camera Setup This section describes how to configure the network camera and is intended for product Administrators who have unrestricted access to all the Setup tools and Operators who have access to the settings for Basic Live View Video amp Image and System Configuration The network camera is configured by clicking Setup in the top right hand corner of the Live View page Click on to access the online help that explains the setup tools When accessing the network camera for the first time the Connect to 192 168 12 210 Admin Password dialog appears Enter your admin name and FA password set by the administrator di The server 192 168 12 210 for IP cameras requires a username and password Warning This server is requesting that your username and password be sent in an insecure manner basic authentication Note If the password is lost the network camera must iia be reset to the factory default settings See 3 6 Resetting to the Factory Default Settings The default administrator username is ADMIN and password is 1234 User name f v Password C Remember my password 11 3 6 Resetting to the factory default settings To reset the network camera to the original factory settings go to the Setup gt System gt Maintenance web page
5. an Live View EE ESA Ve Lo vr Ar gt SE e HAVS AnA CINTEN 3 2 Access from the internet Once connected the network camera is accessible on your local network LAN To access the network camera from the Internet you must configure your broadband router to allow incoming data traffic to the network camera To do this enable the NAT traversal feature which will attempt to automatically configure the router to allow access to the network camera This is enabled from Setup gt System gt Network gt NAT For more information refer to 3 5 6 System gt Network gt NAT of User s Manual 3 3 Setting the admin password over a secure connection To gain access to the product the password for Connect to 192 168 12 210 the default administrator user must be set This is done in the Admin Password dialog which is displayed when the network camera is accessed for the setup at the first time Enter your admin The server 192 168 12 210 for IP cameras requires a name and password set by the administrator an Warning This server is requesting that your username and password be sent in an insecure manner basic authentication without a secure connection Note The default administrator username is User name ADMIN and password is 1234 If the Password OOOO E password is lost the network camera must be a reset to the factory default settings See section 3 8 Resetting to the Fac
6. network and requires an IP address for access Most networks today have a DHCP server that automatically assigns IP addresses to connected devices By the factory default your camera is set to obtain the IP address automatically via DHCP server If your network does not have a DHCP server the network camera will use 192 168 1 100 as the default IP address If DHCP is enabled and the product cannot be accessed run the Smart Manager utility on the CD to search and allocate an IP address to your products or reset the product to the factory default settings and then perform the installation again 1 Connect the network camera to the network and power up 2 Start SmartManager utility Start gt All programs gt SmartManager gt SmartManager the main window displays After a short while any network devices connected to the network will be displayed in the list 1 SmartManager JOE File View Help a es All Device U IP Filter Model Name IMAC Address IP Address Wireless IP Address Zero Conf IP Version Le All Devices 1 l 07 D8 00 F1 F5 192 168 30 221 0 0 0 0 169 254 19 215 1 5 2 Tb_release CE202D WNPT 1 ONVIF 1 Group 3 Select the camera on the list and click right button of the mouse The pop up menu below displays 1 SmartManager JI File View Help ca of All Device AlDevce v C IP Filter Model Warne Name MAC Address IP Address Wireless
7. Quick Guide XX269 10 00 CE202D WN Network Outdoor Camera Dome CEFE Vicon Industries Inc Tel 631 952 2288 Fax 631 951 2288 Toll Free 800 645 9116 24 Hour Technical Support 800 34 VICON 800 348 4266 UK 44 0 1489 566300 Vicon Industries Inc does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation This system has not been designed to be used in life critical situations and must not be used for this purpose www vicon security com Document Number 8009 8269 10 00 Issued 214 Product specifications subject to change without notice Copyright 2014 Vicon Industries Inc All rights reserved 1 Description The information in this manual provides quick installation and setup procedures for the CE202D WN Camera Dome These units should only be installed by a qualified technician using approved materials in conformance with federal state and local codes Read these instructions thoroughly before beginning an installation Always refer to Vicon s website to assure you have the most up to date manual www vicon security com The CE202D WN is designed for demanding outdoor security installations This cost effective fixed network camera includes an integral 3 7 mm megapixel fixed lens the 1080p resolution delivers crisp clear images The CE202D WN camera is fully compatible with all Vic
8. iling 2 Disassemble the camera by loosening the four 4 captive screws securing the cover and removing the camera cover 3 Secure the dome camera to the ceiling using the anchors 2x and screws 2x provided in the accessory kit Camera Cover Dome Camera Template Sheet e Camera Dimension The diagram below provides dimensions Side View Bottom View Dimensions Unit mm 2 2 Connections e Connection Cable NO Name Descriptiom lt lt OOC Audio Cable Audio line output RCA Jack Red 12 VDC Power Cable White GND Blue GND Gray ALARM INPUT 3 ALARM Cable Brown GND Yellow ALARM OUT 4 Ethernet Cable Ethernet RJ 45 port compatible with 10 100Mbps having PoE functionality Modular Jack Video Output BNC port g x A N a I ES Io Optional OSD Controller NO Name Micro SD Slot Micro SD memory slot Factory Default Button Button for the factory default setting Microphone input Microphone input Service Monitor set to NTSC by default change video format 4 Service Monitor Port from Source menu V920D OSD Controller option Communication Port Mono Jack e Connecting to the RJ 45 Connect a standard RJ 45 cable to the network port of the network camera Generally a cross over cable is used for direct connection to a PC while a direct cable is used for connection to a hub e Micro SD memory slot Insert the SD memory card customer supplied
9. onNet systems its ONVIF certification provides an open platform for integration into other video management systems The network camera provides triple streaming video and supports H 264 compression technology MPEG 4 and Motion JPEG M JPEG compressions are also provided as are privacy masking and motion detection Installation is made easy and cost effective with Power over Ethernet PoE the camera also accepts 12 VDC e Installation Steps Follow these steps to install the network camera on your local network LAN Check the package contents against the list that follows Connect the network camera Set an IP address Set the password u SS 1 1 Components The system comes with the following components 1244 10 00 _ 0 m _ Camera Unit Installation CD Installation Guide Accessory Kit Template Sheet Optional OSD Controller Note 1 Check your package to make sure that you received the complete system including all components shown above Note 2 Adapter for 12 VDC is not supplied the optional V920D OSD Controller can be purchased separately e Contents in the installation CD 1 The CE202D WN User s Manual 2 The SmartManager User s Manual 3 The SmartManager Installation software 2 Installation e Camera Installation Carefully remove the contents from the box and verity that nothing was damaged in shipment 1 Using the template sheet provided make screw holes for camera on the ce
10. t button takes a picture snapshot of the current image The location where the image is saved can be specified The digital zoom activates a zoom in or zoom out function for video image on the live screen The Full Screen button causes the video image to fill the entire screen area No other windows will be visible Press the Esc button on the computer keyboard to cancel full screen view The Manual Trigger button activates a pop up window to manually start or stop the event The PT button activates a pop up window for Pan and Tilt control E Use the speaker icon scale to control the volume of the speakers a Use the microphone icon scale to control the volume of the microphone 3 Video Streams 4 The network camera provides several images and video stream formats Your requirements and the properties of your network will determine the type you use The Live View page in network camera provides access to H 264 MPEG 4 and Motion JPEG video streams and to the list of available video streams Other applications and clients can also access these video streams images directly without going via the Live View page Pan and Tilt Control You can control Pan and Tilts from the live view screen Press the button on the left top in the live view screen to activate the control panel 10 Q Emm 1 O Live View H 264 Mini PT Dome e 192 168 30 221 ARA MA ZZ i gt CITTA e Adjusting Pan and
11. tory Default Settings for more details 3 4 Live View Page The live view page comes in several screen modes 1920x1080 1280x1024 1280x720 704x480 576 640x480 352x240 288 and 320x240 Select the most suitable mode in accordance with your PC specifications and monitoring purposes 1 General controls 07 Live View Page Wa J searcr amp Playback Page Pse Page Help Page Q The video drop down list allows you to select a customized or pre programmed video stream on the live view page Stream profiles are configured under Setup gt Basic Configuration gt Video amp Image For more information see section 3 5 1 Basic Configuration gt Video amp Image of User s Manual 1920x1080 el The resolution drop down list allows the selection of the most suitable video resolutions to be displayed on Live View page 9 The protocol drop down list allows the selection of the combination of protocols and methods to use depending on your viewing requirements and on the properties of the network 2 Control toolbar The live viewer toolbar is available on the web browser page only It displays the following buttons O The Stop button stops the video stream being played Pressing the key again toggles the start and stop The Start button connects to the network camera to start playing a video stream o The Pause button temporarily stops pauses the video stream being played y The Snapsho
Download Pdf Manuals
Related Search