Verint Nextiva S1700e Series Installation guide
Contents
1. 2 Ona PoE device power it and connect it to the network using the PoE kit 3 On a 12V DC device power it with a power supply then plug the straight through or crossover network cable to the LAN 10 100 connector 20 Verint Video Solutions Nextiva S1700e Series Installation Guide 4 If required on a PoE device connect the power wires of a camera to the DC Pwr poles on the connector on the back of the device For the maximum length of the camera power wire refer to the S1700e Series User Guide 5 If required connect the serial port of the transmitter to a PTZ camera Verint Video Solutions 21 2 Configuration and Installation 6 When installing a device with the extended temperature option make it stand vertically allowing for better cooling Status LED The system status LED is a bicolor green red LED providing detailed information on the current state of the device Condition Indication Steady red for 5 sec The device is powering up Flashing red 1 sec The IP address of the device is already assigned to intervals another device on the network Flashing green 3 sec The firmware has started but the device is not intervals connected to the network 22 Verint Video Solutions Nextiva S1700e Series Installation Guide Condition Indication Flashing green 1 sec intervals The firmware has started the device is connected to the network but no video audio serial2. computer requirements 8 configuration camera data port 2 device 8 17 connection PoE 9 11 point to point 17 power 12 crossover Ethernet cable 11 customer service viii D DC Pwr poles 9 20 description form 27 DHCP Dynamic Host Configuration Protocol 16 Verint Video Solutions Index enclosure of the device 4 equipment list 3 Ethernet cable 10 11 extranet Verint Video Solutions viii F features of the device 2 form device description 27 I injector PoE 9 11 IP address 13 L LED status 22 length of Ethernet cable 10 list of equipment 3 maximum length of Ethernet cable 10 o options when ordering a device 3 25 Index P V panel of device 4 Verint Video Solutions web site vii PoE power over Ethernet injector 9 11 Ww point to point connection 17 power connection 9 11 12 power requirements 2 power supply 9 power up conditions 23 web site Verint Video Solutions vii R requirements computer 8 power 2 S SConfigurator configuring the device 8 13 17 creating a connection 18 shipment list 3 SmartSight Utilities CD vii status LED 22 straight through Ethernet cable 10 11 support technical viii T technical support viii U Utilities CD vii 26 Verint Video Solutions Edge Device Description Form Verint Video Solutions 27 Edge Device Description Form During configuration write down the following settings that may be required by Verint Video Solutions cu
3. data is transmitted Flashing green 0 2 sec intervals The firmware has started the device is connected to the network and video audio serial data is transmitted Three consecutive red blinks every 2 sec No video source is detected and no video is transmitted Flashing green red 1 sec intervals The device is undergoing a firmware update Flashing red 0 1 sec intervals The device is being identified At least one of them must be transferred to obtain the LED condition The following power up conditions on the system status LED are abnormal W LED not lit Check the power supply and cabling If power is available and the LED stays off call Verint Video Solutions customer service for assistance W Steady red LED persisting more than 10 seconds There is an internal error that prevents the device from starting normally Power down the device wait 30 seconds then power it up If the condition persists call Verint Video Solutions customer service Verint Video Solutions 23 2 Configuration and Installation W Flashing green red LED not during a firmware update The device is in backup mode you will need to perform a firmware update using a serial connection 24 Verint Video Solutions A abnormal power up conditions 23 C cable Ethernet 10 11 camera data port configuration 2 powering 20 casing of the device 4 CD Utilities vii characteristics of the device 2
4. M Forward 1 0 N Forward Serial Port Data IV Enable Audio PTT PTL Cancel Verint Video Solutions Nextiva S1700e Series Installation Guide 4 Select a transmitter in the left column and a receiver in the right one In the Transmitters column you have access to the two encoders of each input the video stream is the same for both Stream1 is typically reserved for web viewing therefore you should use Stream2 for point to point connections 5 In the Video list select the desired video mode 6 To disable I O data transmission for example alarms between the two selected devices clear Forward I O 7 To disable serial port data transmission like PTZ commands clear Forward Serial Port Data 8 To enable audio between the devices ensure that Enable Audio is checked then select the audio mode 9 Click Connect You should now have video on the monitor connected to the receiver Verint Video Solutions 19 2 Configuration and Installation Installation When your device is successfully configured it is ready to be installed in its final location If your S1700e device is powered using PoE you can use the two DC Pwr poles on the back of the device to power a camera The supply voltage of the camera must be 12V DC 10 its maximum power consumption must be 5W 417 mA To install the device 1 Plug the video cable of the camera to the video input connector on the device
5. Nextiva S1700e Series Installation Guide VERINT POWERING ACTIONABLE INTELLIGENCE Nextiva S1700e Series Installation Guide Verint Video Solutions 2005 Verint Systems Inc All rights reserved By providing this document Verint Systems Inc is not making any representations regarding the correctness or completeness of its contents and reserves the right to alter this document at any time without notice Verint Actionable Intelligence BehaviorTrack Dellis HealthCheck I Rooms Lanex Loronix Loronix Video Manager MotionTrack microDVR nDVR netDVR Nextiva Powering Actionable Intelligence RP Security Safe on the Move SmartSight Video Manager and WebReview are trademarks of Verint Systems Inc its subsidiaries or affiliates All other registered trademarks trademarks and any associated logos are the properties of their respective owners Published by Verint Video Solutions 1800 Berlier Street Laval Quebec Canada H7L 454 www verint com videosolutions Publication date December 12 2005 Contents dic cm v Who Should Read this Guide s sssssssssrrssrrnrrrrrrrnrrrnrrnnrrnrrrnernne vi How to Use this Guide u nn na bl vi About US cdd eo e inest e ER awed dune ai vii Chapter 1 m Overview nusnunnannnnannnnannnnannanannanunnanunnannnnunnnnannnnannane 1 About the S1700e Serles HH He een iin 2 SNIPMENE nenn ie i 3 Casing Description sers er uu
6. ation and installation procedures of the device An index and a device description form complete the guide vi Verint Video Solutions Nextiva S1700e Series Installation Guide In addition to this guide the following documentation is also available W Nextiva S1700e Series User Guide m SConfigurator User Guide W Release Notes All these documents are contained on the SmartSight Utilities CD shipped with the device About Us Verint Systems NASDAQ VRNT is a leading global provider of video security surveillance and business intelligence solutions Verint Video Solutions transform digital video into actionable intelligence timely mission critical insights for faster more effective decisions Today more than 1000 companies in 50 countries use Verint Systems solutions to enhance security boost operational efficiency and fuel profitability Web Site For information about the Nextiva line of products visit www verint com videosolutions To download data sheets and user documentation use the following link www verint com smartsight support Verint Video Solutions vii Preface To request the latest versions of firmware and software or to download other product related documents you need access to the Verint Video Solutions partner extranet To register go to http vvs verint com Support If you encounter any type of problem after reading this guide contact your local distributor or Verint Video Sol
7. ector for the RS 232 serial port VERINT Nextiva o Elo Reset LAN 10 100 Status RS232 System status Reset RJ 45 Ethernet 4 Verint Video Solutions Nextiva S1700e Series Installation Guide The back panel consists of W A 12 pole connector for power dry contact inputs relay outputs and RS 422 485 W One BNC connector for video input W Optional audio connectors W Aslot for an SD device for future development 12V DC RS 422 485 Audio optional Video 2 Video 1 Audio OO SD card Input output Video SD card slot Verint Video Solutions 5 Verint Video Solutions Configuration and Installation The steps required to prepare your S1700e device for operation are mM Basic configuration mainly for communication and serial connection W Physical installation in its final location Verint Video Solutions 2 Configuration and Installation Configuration The configuration steps to execute are W Assembling the power over Ethernet kit on the PoE devices only MH Setting a series of parameters including the IP address MH Establishing a point to point connection between a receiver and a transmitter if required To configure the device you need the proprietary SConfigurator tool It is included on the SmartSight Utilities CD shipped with your device you can also find its latest version on the Verint Video Solutions extran
8. er si ioi xi General Units Connections Units E 192 168 135 114 Unit Receiver 192 168 135 114 S1S00e amp 192 168 135 215 Unit Receiver 192 168 135 215 515006 Add Unknown 169 254 31 68 Unknown 4 Unknown 3unit s discovered A device of type Unknown with a 169 254 X Y IP address appears in the Units box it corresponds to your new device Verint Video Solutions 15 2 Configuration and Installation 8 Select the unknown device then click Configure In the Reconfigure unit confirmation window click Yes The New Network Configuration window appears r Network Configuration Use DHCP M IPAddress 172 16 8 Subnet 255 255 0 Gateway 0 0 0 0 0 0 Host Name xl To use DHCP Dynamic Host Configuration Protocol check Use DHCP Otherwise enter the IP address subnet mask and gateway of the device as provided by your network administrator For more information about DHCP refer to the S1700e Series User 9 Guide 10 Click OK 16 Verint Video Solutions Nextiva S1700e Series Installation Guide 11 In the Units tab click Discover The new S1700e device appears 12 Select the device then click Configure 13 Configure the serial port parameters to match those of the target equipment for instance camera or PTZ keyboard For more information refer to the SConfigurator User Guide The S1700e initial configuration is now complete Po
9. et Technical Support then Downloads then Firmware Upgrades You have to copy its executable file to the hard disk of your computer The minimum hardware and software requirements for the host computer needed to configure the edge device are An Ethernet network card A serial port not through a USB converter Internet Explorer 6 0 Microsoft DirectX 8 1 Windows 2000 Service Pack 2 or higher or Windows XP Service Pack 2 8 Verint Video Solutions Nextiva S1700e Series Installation Guide Assembling the PoE Kit You use the supplied power over Ethernet PoE kit to power the S1700e PoE device and establish the Ethernet connection The kit contains two items an injector and a power cord Warning Ona PoE device never connect an external power supply in the DC Pwr poles on its back Verint Video Solutions 2 Configuration and Installation To assemble the PoE kit Straight through O Ethernet cable 3 4 Ethernet cable straight through or J1 DATA amp PWR DATA crossover PoE injector J Power cord 1 Ina lab unpack the device and its PoE injector and place them on a table 2 Plug a straight through Ethernet cable into the LAN 10 100 connector on the front of the S1700e device Note The maximum length of this cable is 164 feet 50 meters 10 Verint Video Solutions Nextiva S1700e Series Installation Guide 3 Plug the other end of the cable into the DATA amp PWR port o
10. f the injector 4 Connect a second Ethernet cable straight through or crossover into the DATA port of the injector The crossover cable is to directly connect the device to a computer the straight through cable is to integrate the S1700e on a network Note The maximum length of this cable is 82 feet 25 meters 5 Connect the other end of the second cable into an Ethernet device for example a switch or a computer Warning To avoid damaging your Ethernet equipment ensure that the cable is connected into the DATA port of the PoE injector and not in the DATA amp PWR port 6 Power the S1700e device by plugging the power cord between the injector and the outlet Verint Video Solutions 11 2 Configuration and Installation Preparing a 12V DC Device To prepare a 12V DC device for configuration 1 2 12 In a lab unpack the S1700e and place it on a table Establish the Ethernet connection by plugging a cable crossover or straight through into the LAN 10 100 connector on the front of the device The crossover cable is to directly connect the device to a computer the straight through cable is to integrate the S1700e on a network Warning Never plug a PoE injector into the LAN 10 100 connector on an S1700e 12VDC device Otherwise the device will be damaged and the warranty becomes void Power the device If you are using the supplied power supply a Plug the power supply wire with the dashed white li
11. int to Point Connection To view video on a monitor in a point to point context as opposed to using a video management software you have to create a fixed connection between an S1700e transmitter and an S1500e receiver Typically both devices sit on the same IP subnet as SConfigurator and have the same VSIP port to access other devices refer to the device discovery section in the SConfigurator User Guide Note The receiver must be running firmware version 3 10 or higher For more information about the connection procedure or the video modes refer to the Managing Connections chapter in the SConfigurator User Guide Verint Video Solutions 17 2 Configuration and Installation To perform a point to point connection 1 2 18 Start SConfigurator In the Units tab discover the desired devices The discovered devices appear in the Units box Select the Connections tab then click Add The Connection Creator window appears Connection Creator E Transmitters Receivers 172 16 30 51 Inputl Encoderl 172 15 30 4 Qutputl Decoder 172 16 30 51 Inputl Encoder2 172 15 30 4 0 utput2Decoderl 172 16 30 50 Inputl Encoder 172 16 30 4 Output3Decoderl 172 16 30 50 Inputl Encoder2 172 15 30 4 0utput4Decoderl 172 16 30 19 Input1 Encoder 172 16 30 136 Output1 Decoder 72 16 30 19 Inputl Encoder2 172 15 30 20 Inputl Encoder 172 16 30 20 Inputl Encoder2 172 16 20 ANN Anni F nendert zl Video RTP_UDP m
12. itor nene nn een 4 Chapter 2 m Configuration and Installation ses 7 Configuration scs viecece setae u dene env ed emergere giai eee ree e ehe 8 Assembling the POE Kit ii 9 Preparing a 12V DC Device ri 12 Setting Device Parameters v eren ren 13 Point to Point Connection u ak rd 17 Installation Sa Aa en er e ERE Ecce Dec cure RR art ones 20 Sy BB IcH U BISFRRRSERREHRREHREHRERFREEFERERFRPRPEFFURPEFEEFHERFEREEFERERFEERPEFTIEFERERFR 22 Verint Video Solutions iii Contents iv Verint Video Solutions Preface The Nextiva S1700e Series Installation Guide explains how to configure and install the Nextiva S1700e series edge devices Verint Video Solutions v Preface Who Should Read this Guide This guide is intended for engineers and technicians who will install the S1700e series edge devices It provides basic information on how to configure and install the devices This guide assumes that you are familiar with Installation and manipulation of electronic equipment W General use of computers W Basic network concepts and practices W Microsoft Windows operating systems How to Use this Guide The Nextiva S1700e Series Installation Guide is divided into the following chapters 1 Overview Provides a brief description of the features of the S1700e series device and illustrations of its casing 2 Configuration and Installation Presents the configur
13. nes in the GND pole on the back of the device b Plug the other power wire in the 12V pole on the back of the device Cc Connect the electric plug into the outlet For any other power supply refer to the manufacturer documentation for the proper wiring scheme Verint Video Solutions Nextiva S1700e Series Installation Guide Setting Device Parameters The first step in installing an S1700e device is to change its IP address to ensure compatibility with an existing network Write down the IP information in the form located at the end of the guide on page 27 To set the parameters of a device 1 Ensure that the device has power and is connected to the network 2 Start SConfigurator The SConfigurator window appears Verint Video Solutions 13 2 Configuration and Installation 3 Inthe General tab click Program Options The Program Options window appears IP Address of the PC Detect All Units on LAN IT Discovery IP Address 255 255 255 255 Reset to Reset to Broadcast Multicast SEL Trusted Unit List Browse Enable Security I Enter SSL Passkey a 4 Ensure that the VSIP Port is 5510 otherwise click Default 5 Ensure that the Discovery IP Address is 255 255 255 255 otherwise click Reset to Broadcast 6 Check Detect All Units on LAN then click OK 14 Verint Video Solutions Nextiva S1700e Series Installation Guide 7 Select the Units tab then click Discov
14. stomer service for troubleshooting System Firmware version VSIP VSIP port Video Bit rate Frame rate Resolution Network IP address Gateway Subnet mask Security SSL passkey 28 Verint Video Solutions Verint Video Solutions 1800 Berlier Street Laval Quebec Canada H7L 4S4 VERINT POWERING ACTIONABLE INTELLIGENCE
15. t popular camera data port configuration 4800 baud 8 data bits no parity 1 stop bit The S1700e series currently holds a single transmitter the S1700e T It offers the following features One video input The choice of either 48V DC power over Ethernet PoE or 12V DC Three dry contacts for input and one relay output One optional pair of audio I O connectors Two independent serial ports for the RS 232 and RS 422 485 protocols W A reset button You can also purchase a 12V DC device without audio with the extended temperature option XT Unless otherwise specified the word S1700e refers to any of these devices 2 Verint Video Solutions Nextiva S1700e Series Installation Guide Shipment Your S1700e shipment contains the following items W The requested transmitter device W Either a power over Ethernet kit injector and power cord or a 12V DC external power supply W The SmartSight Utilities CD containing the release notes and documentation for the device as well as the SConfigurator application W This installation guide The shipment may also contain the following option W A 10 device rack mount panel SRM10 Verint Video Solutions 3 1 Overview Casing Description The S1700e electronics are enclosed in a non weatherproof steel casing that is not meant for outdoor use The front panel consists of An RJ 45 jack for PoE or the Ethernet network W A system status LED W A reset button W A DB 9 conn
16. utions representative You can also use the following sections on the Verint Video Solutions partner extranet to find the answers to your questions E SmartSight FAQ W SmartSight Requests W SmartSight My Account For assistance with the Nextiva edge devices and the related software contact the Verint Video Solutions customer service team W By phone 1 888 494 7337 option 1 North America or 1 450 686 9000 option 1 Monday to Friday from 8 30 to 17 30 EST E By fax 1 450 686 0198 viii Verint Video Solutions Overview Designed for video monitoring and surveillance over IP networks the S1700e series edge device is a self contained solution delivering DVD quality 4CIF video at 30 frames per second in NTSC 25 frames in PAL over 10 100Base T networks Two compression modes are available a proprietary MPEG 4 based mode and the MPEG 4 ISO 14496 2 compliant mode The device can easily be extended over LANs and WANs or the Internet using ISDN PSTN or xDSL routers It is built on open standards to provide long term investment protection The S1700e series edge devices can be used in point to point contexts as well as with video management and storage applications Furthermore they enable configuration and video viewing from web browsers Verint Video Solutions 1 1 Overview About the S1700e Series The S1700e series devices are for indoor use only Each device is configured to interface right out of the box with the mos
Download Pdf Manuals
Related Search