Code Alarm ca6554 Installation guide
Contents
1. To Door Lock Motor 2014 Voxx Electronics Corporation All rights reserved 17 Negative Multiplexed Locks All Door Lock and Unlock Locate the lock unlock wire at the vehicle s lock unlock switch Verification This wire will show variable ground when the switch is activated Please consult the wire and location chart for specific resistor values for your vehicle Connect the GREEN and BLUE or BLUE GREEN wires shown in the diagram below using 2 SPDT relays not supplied Multiplex Locks Ground Fused 12 Volt Battery Source GREEN Lock Output BLUE Unlock Output Control Relays Positive Multiplexed Locks All Door Lock and Unlock Locate the lock unlock wire at the vehicle s lock unlock Switch Resistor Verification This wire will show variable positive voltage when the switch is activated Please consult the wire and location chart for specific resistor values for your vehicle Connect the GREEN and BLUE or BLUE GREEN wires shown in the diagram below using 2 SPDT relays not supplied Multiplex Locks Fused 12 Volt Battery Source GREEN Lock Output BLUE Unlock Output Vehicle Door Lock Control Relays 18 ca6554 Install revA Adding Aftermarket Actuators After installing aftermarket actuators not supplied2. SHOCK SENSOR amp HARNESS 4700023 RED BATTERY 12V BLACK GROUND WHEN ARMED BLUE FULL TRIGGER GREEN WARN AWAY TRIGGER ca6554 Install revA 2014 Voxx Electronics Corporation All rights reserved 39 40 Voxx Electronics Corporation Customer Service 1 800 421 3209 WWW CODE ALARM COM FCC COMPLIANCE This device complies with Part 15 of the FCC rules and with RSS 210 of Industry Canada Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including any interference that may cause undesired operation Warning Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment PATENTED www voxxintl com company patents ca6554 Install revA
3. Connect the GREEN and BLUE wires shown in the diagram below using 2 SPDT relays not supplied Fused 12 Volt Battery Source Door Lock Actuator GREEN Lock Output Chassis Ground BLUE Unlock Output Chassis Ground 2014 Voxx Electronics Corporation All rights reserved 19 Additional Ports Antenna LED Programming Port Mount the supplied antenna receiver to a clear spot on the vehicle s windshield that will not block the driver s vision A good location is usually high on the windshield near the rear view mirror Be careful not to mount the antenna receiver on any metallic window film as this will effect system range Route the antenna receiver cable to the control module and plug into the antenna port Data Bus Interface Port This 4 pin port is used for Flashlogic Door Lock and Transponder Databus Interfaces to communicate with the vehicle s Databus When using the DBI port to control the Flashlogic Door Lock and Transponder Interface modules the following options may be available Please refer to the D2D Data to Data function list available per vehicle on the tech service web site Tach Input Brake Safety Shut Down Door Trigger Trunk Hatch Open Door Lock Control Passlock Passkey Interface GM Only Dome Light Supervision Transponder Interface Activation Factory Alarm Arm Disarm Diesel Glow Plug Input Manual Arm Disarm Inputs factory keyless controls system Telematic
4. OFF Press and Hold Valet Button Press Start 4 times Daily Start Timer x Press Lock Start Menu Press and Hold Temperature x Press Unlock Start While Armed Start AUX 2 3 4 5 Access in AUX Mode Press and Hold F for 2 seconds Enter AUX Mode x LCD displays AU AUX 2 Push and Hold 3 Sec AUX 3 x Push and Hold 3 Sec AUX 4 Push and Hold 3 Sec AUX 5 Push and Hold 3 Sec ca6554 Install revA Security Trigger Zones If the security system has been triggered the LED will flash one of the patterns below indicating the zone LED FLASHES 2 Flashes 3 Flashes 4 Flashes 5 Flashes TRIGGER ZONE Hood Trunk Input Door Input Shock Sensor Ignition Input Remote Start Shutdown Diagnostics If the remote start shuts down or fails to start the parking lights will flash one of the patterns below indicating the shutdown input To manually enter diagnostics and view the last shutdown turn the ignition ON and press and release the button LED FLASHES 3 Flashes 4 Flashes 5 Flashes 7 Flashes 2014 Voxx Electronics Corporation All rights reserved SHUTDOWN ZONE Hood Input Brake Input Neutral Safety Input Remote Start Valet Mode Manual Transmission Mode not set manual transmission models only Tach not learned Crank Average not learned 4120290 4120291 CODEALARM 554 4360519 4120110 4120145 4120184 1032714 4
5. Seconds 6 Security ON OFF 7 Anti Hijack Mode OFF 8 Orange Ground w Armed Output While 9 DBI Port Protocol DBI Protocol ADS Protocol E Standard Inverted 10 pur Light Pattern B pem 5 Eu EN ca6554 Install revA Feature Bank 3 5 Chirps 1LEDFlash 2LED Flash 3LEDFlash 4LED Flash 5LED Flash 6 LED Flash Output Control 1 Second 30 Second Double Pulse 1 Extended Lock Pulse 1 Second 3 5 Seconds Lock Double Lock Double Lock 1 Pulse Unlock Pulse Unlock Second Unlock 2 Factory Disarm Unlock Factory Disarm Factory Disarm Factory Disarm Lt Green Black 6 Pin hamess learn Start Status 350mS Pulse 500mS Pulse 1Sec Pulse m Lock and 3 lgnition Controlled Locks OFF Lock Only Unlock Only Unlock Latched ON Trunk Output Timing 1 Second Latched until A 4 Red White Output Pulse 10 Seconds 20 Seconds IGN ON until Button Press 5 Hom Output Timing 16mS 10mS 30mS 40 5 50mS 6 Real Panic ON OFF AUX 1 1 Second Latched until Dome Light Defrost Output Defrost Output 7 Violet Black Output Pulse IGN ON Output Single Ruse S Min After Start After Start AUX2 1Second Latched until 10 Second Sene White Black Output Pulse IGN ON Pulse with Arm Use Wi Disarm y AUX3 1Second Latched until 10 Second R Fr Gray Black Output Pulse R IGN ON Pulse with Arm 099 wi Di
6. and does not change the output of the factory disarm wire on the 4 pin alternate output harness Factory Disarm Single 1 second pulse with unlock and remote start activation 2nd Unlock Same output as unlock with 2nd press of unlock Factory Disarm Start Status Single 1 second pulse with unlock and continuous output during the remote start cycle Factory Disarm Single 350mS second pulse with unlock and remote start activation Factory Disarm Single 500mS second pulse with unlock and remote start activation ca6554 Install revA 3 Ignition Controlled Locks Control of door locks when the ignition is cycled ON or OFF OFF Door locks not activated by ignition Lock and Unlock Doors lock when ignition is turned on and unlock when ignition is turned off Lock Only Doors lock when ignition is turned on Unlock Only Doors unlock when ignition is turned off 4 Trunk Output Timing Red White Output Controls the output timing type of the RED WHITE output 1 Second Pulse 1 second pulse output 10 Second Continuous output for 10 seconds 20 Seconds Continuous output for 20 seconds Latched until IGN ON Continuous output until the vehicle s ignition is turned ON Latched ON until Button Press Continuous output until the activation button is pressed again 5 Horn Output Timing Control the minimum horn pulse time in milli seconds some vehicle will require a longer pulse to activate the fa
7. the vehicle was started with the key Preset Time Preset starter output time see crank time 2014 Voxx Electronics Corporation All rights reserved 31 32 8 Gas Diesel Selects engine type and delay time for the starter output wire during remote start activation Gas Gasoline engine no delay for the starter output wire 10 Second Delay Diesel engine delays the starter output wire for 10 seconds after the ignition has been powered up by the remote start 15 Second Delay Diesel engine delays the starter output wire for 15 seconds after the ignition has been powered up by the remote start 20 Second Delay Diesel engine delays the starter output wire for 20 seconds after the ignition has been powered up by the remote start 45 Second Delay Diesel engine delays the starter output wire for 45 seconds after the ignition has been powered up by the remote start 9 Single Double Pulse Start Switches the remote start activation between a single or double press from the transmitter 10 Ignition 2 Output Pnik White Programmable high current output Ignition 2 Output becomes active with the same timing as the ignition output and does not drop out during crank Accessory Output becomes active with the same timing as the accessory output drops out during crank Start Crank Output becomes active with the same timing as the starter output wire during crank only 11 2 or 3 Hour Start When activat
8. wire to the vehicle starter wire use the MOTOR SIDE of the vehicle starter wire when installing the starter kill relay 2 RED BATTERY 12V Locate 1 of the vehicle s constant 12 Volt battery wires at the ignition switch Verification This wire will register voltage in all positions of the ignition Switch Connect the RED wire to the constant 12 Volt battery wire NOTE Remove all fuses until all connections are made 3 ORANGE ACCESSORY 1 Locate the vehicle s accessory wire at the ignition switch Verification This wire registers voltage when the key is turned to ACC Accessory and the ON or RUN position The voltage drops out when the key is turned to the START or CRANK position Connect the ORANGE wire to the vehicle s accessory wire ca6554 Install revA 4 PINK WHITE IGNITION 2 Locate the vehicle s 2nd ignition wire at the ignition switch if equipped Verification This wire registers voltage when the key is turned to the ON or RUN position but not the ACC Accessory position The voltage does not drop out when the key is turned to the START or CRANK position Connect the PINK WHITE wire to the vehicle s ignition 2 wire Programmable output IGN ACC Start 5 RED WHITE BATTERY 12V Locate 1 of the vehicle s constant 12 Volt battery wires at the ignition switch Verification This wire will register voltage in all positions of the ignition switch Connect the RED WH
9. 120102 1031423 STARTER INTERUPT RELAY amp HARNESS ORANGE RED BLACK WHITE BLACK OPEN 38 1024405 86 ARMED OUTPUT 85 IGNITION 87A STARTER OUTPUT MOTOR SIDE 30 STARTER INPUT KEY SIDE 87 OPEN BLUE WHITE GREEN PURPLE WHITE BLUE GRAY GRAY RED BROWN RED PURPLE WHITE SHOCK SENSOR PORT TELEMATIC PORT ANTENNA LED VALET PURPLE RED ORANGE PINK WHITE RED WHITE PINK WHITE RED WHITE BLACK BROWN PINK BLACK ORANGE BLACK GRAY BLACK WHITE BLACK BROWN BLACK BLUE BLACK VIOLET BLACK RED WHITE LT GREEN BLACK ORANGE BLACK YELLOW GREEN WHITE LT BLUE LT GREEN BLACK BLUE OPEN GREEN DBI PORT INSTANT TRIGGER INPUT DOOR TRIGGER INPUT DOOR TRIGGER INPUT EXTERNAL START INPUT HOOD INPUT PARKING BRAKE INPUT BRAKE INPUT TACH INPUT Q STARTER OUTPUT MOTOR SIDE BATTERY 12V ACCESSORY 1 IGNITION 2 BATTERY 12V IGNITION 1 PARKING LIGHT INPUT PARKING LIGHT OUTPUT GROUND SIREN OUTPUT AUX 5 OUTPUT AUX 4 OUTPUT AUX 3 OUTPUT AUX 2 OUTPUT HORN OUTPUT START STATUS ACTIVE OUTPUT AUX 1 OUTPUT TRUNK RELEASE OUTPUT FACTORY DISARM PULSE BEFORE START GROUND WHEN ARMED PULSE DURING CRANK PULSE AFTER SHUTDOWN FACTORY ARM PULSE AFTER START FACTORY DISARM PULSE BEFORE START UNLOCK LOCK
10. ACK GROUND Connect the BLACK wire to a solid chassis ground point using a ring terminal and self tapping screw not supplied Scrape away paint from the grounding point to ensure a good connection The recommended grounding point is a metal surface in the driver s side kick panel area NOTE Do not ground the BLACK wire with any other vehicle components 4 BROWN SIREN OUTPUT Locate a suitable mounting location in the engine compartment for the siren away from moving parts With the bell of the siren aiming downwards secure the siren in place using self tapping screws being careful not do drill into any hoses wiring or components Connect the BLACK siren wire to a chassis ground using a ring terminal and self tapping screw not supplied Route the BROWN siren output wire from the control module through the firewall and connect to the RED wire on the siren NOTE Be sure to loom the siren wires and seal the grommet 2014 Voxx Electronics Corporation All rights reserved 6 Pin Start Harness 1 PURPLE STARTER OUTPUT Locate the vehicle starter wire Verification This wire registers voltage only when the key is turned to the START position Cut the vehicle s starter wire in half when installing the starter kill relay Verification after starter wire is cut KEY SIDE of starter wire registers voltage when the key is turned to the START position MOTOR SIDE of starter wire registers no voltage Connect the PURPLE
11. CODE ALARM PROFESSIONAL SERIES Security and Remote Start Installation Guide for models 6554 2014 Voxx Electronics Corporation All rights reserved Table of Contents Before You Bega 4 Wire Connection 5 4 PID Main FaffieSS coin titer eti res sa ee ce ea Seen xi MER SER 7 5 Pe cec ieu oet eo Mere 8 6 Pin Output EIarmess uero neenon cepto Dg IRSE 10 8 Pin Input ao 11 4 Pin Alternate Output 55 14 4 Pin AUX Output Harness occi ten bcnc e t ER OS ie 15 3 Pin Door Lock Output Harness cerita 16 Additional 20 Antenna LED Programming Port 20 DBI POf e 20 Tel maticnterfacePORt s s caer ratae rare peer en ht e rege EEG 20 Set Up amp Programmiltng reete iere eater teretes 21 Transmitter 21 Manual Feature Programming essent 21 Programming Feature Banks 22 Tach Programming c rt 25 smart TachlessMOGOG 25 Adjusting the Shock Sensor 26 Testing the Shock Sensor enne 26 Chirp Delete User 55 26 Dom
12. ITE wire to the constant 12 Volt battery wire NOTE Remove all fuses until all connections are made 6 PINK IGNITION 1 Locate the vehicle s ignition wire at the ignition switch Verification This wire registers voltage when the key is turned to the ON or RUN position The voltage does not drop out when the key is turned to the START or CRANK position Connect the PINK wire to the vehicle s Ignition wire This wire is also used for Ignition 1 Output 2014 Voxx Electronics Corporation All rights reserved 6 Pin Output Harness 1 BROWN BLACK HORN OUTPUT Locate the vehicle s horn wire Verification This wire will register at positive voltage and register ground when the horn switch is pressed Connect the BROWN BLACK wire to the vehicle s horn wire This is a low current output 200mA 2 BLUE BLACK START STATUS ACTIVE OUTPUT This wire provides a 200mA output when the remote start function is activated and remains until 4 seconds after the remote start is shutdown If this wire will be used for multiple application s a 1 amp diode is required in line with the stripe facing the control module 3 VIOLET BLACK AUX 1 This wire provides a 200mA output capable of driving relays For Control of optional accessories i e Power Window Sunroof etc To activate refer to the transmitter button configuration chart Please refer to the selectable options for timing 4 RED WHITE TRUNK
13. Interface Port 20 This 4 pin port is used for telematic Interface accessories such as Car Connection Pro which can control some of the following features Door Lock Control Trunk Release Sliding Doors AUX Output Car Find Remote Start ca6554 Install revA Set Up amp Programming Transmitter Programming Feature Bank 1 Turn the ignition ON Press and hold the valet override button Within 10 seconds the system will chirp 3 three times Press 1 button of each transmitter you wish to program The system will respond with 1 chirp for each accepted transmitter Pressing the override button at anytime during programming will advance to the next bank DLA ON NOTE The system will exit transmitter programming after 15 seconds of inactivity NOTE This system has 1 button programming which programs all channels of the system NOTE The system will hold up to 4 transmitters in memory programming a 5th transmitter will erase the oldest transmitter in memory NOTE This system has PTN Programmed Transmitter Notification Each time the ignition is turned ON the LED will flash the number of transmitters programmed to the system Transmitter programming for 2 Car Mode 2 way system only idis Enter the transmitter into 2 Car Mode Refer to transmitter operation in the owners manual for 2 car operation 2 Follow the steps above for transmitter programming NOTE 2 car mode requires an additional security system in
14. RAKE is engaged NOTE The following connection is required for Manual Transmission Mode ca6554 Install revA 7 BROWN RED BRAKE INPUT Locate the vehicle s brake light wire at the brake pedal mounted switch This connection is required for remote start Verification This wire registers positive voltage when the brake pedal is pressed Connect the BROWN RED wire to the vehicle s brake light wire 8 PURPLE WHITE TACH INPUT Locate the vehicle s ignition coil or fuel injector in the engine compartment Verification Test using the following procedure Set voltmeter to AC VOLTS Attach positive lead of a volt meter to a constant 12 volt source Attach negative lead of a volt meter to the wire to be tested Start the engine Have someone press on the gas pedal slightly as you monitor the meter If connected to the correct wire the voltage reading will increase as the engine s RPM increases Connect the PURPLE WHITE wire to the negative side of the vehicle ignition coil or fuel injector RON 2014 Voxx Electronics Corporation All rights reserved P 4 Pin Alternate Output Harness 1 LT GREEN BLACK FACTORY DISARM PULSE BEFORE START This wire will supply a 200mA pulse both upon disarming the system and when the remote start feature is activated Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door Verification This wire registers ground if the key is turned to t
15. RELEASE OUTPUT Locate the vehicle s trunk release wire at the trunk release switch Verification This wire will register either positive voltage or ground when the trunk release is activated This is a low current 200mA output and in configurable in option programming o ca6554 Install revA 5 LT GREEN BLACK FACTORY DISARM PULSE BEFORE START This wire will supply a 200mA pulse both upon disarming the system and when the remote start feature is activated Locate the factory perimeter alarm disarm wire from the key cylinder inside the drivers door Verification This wire registers ground if the key is turned to the unlock position in the driver s door cylinder Connect the LIGHT GREEN BLACK wire to the factory alarm disarm wire 6 ORANGE GROUND WHEN ARMED OUTPUT This wire will have a continuous 500mA output when the system is Armed This wire is typically used for controlling the starter interrupt relay as well as window modules or additional sensors This output can be configured in option programming 8 Pin Input Harness 1 BLUE WHITE INSTANT TRIGGER INPUT This wire is a GROUND input for an external sensor or secondary pin switch Verification This wire when connected will trigger the security system 2 GREEN DOOR TRIGGER INPUT Locate the vehicle s dome light or door pin switch wire Verification This wire will register ground NEG when the door is opened and the inte
16. TORY DISARM PULSE BEFORE START ORANGE GROUND WHEN ARMED OUTPUT 6 PIN OUTPUT 2014 Voxx Electronics Corporation All rights reserved 8 Pin Input Harness BLUE WHITE INSTANT TRIGGER INPUT GREEN DOOR TRIGGER INPUT PURPLE DOOR TRIGGER INPUT WHITE BLUE GRAY GRAY RED BROWN RED PURPLE WHITE EXTRENAL START INPUT HOOD PIN INPUT 8 PIN INPUT PARKING BRAKE INPUT BRAKE INPUT TACH INPUT 4 Pin Alternate Output Harness BLACK YELLOW PULSE DURING CRANK GREEN WHITE PULSE AFTER SHUTDOWN LT BLUE FACTORY ARM PULSE AFTER START LT GREEN BLACK FACTORY DISARM PULSE BEFORE START ALTERNATE OUTPUT 4 Pin AUX Output Harness 4 PIN AUX OUTPUT 3 Pin Lock Output Harness 1 BLUE UNLOCK 2 REN GREEN LOCK 6 ca6554 Install revA 4 Pin Main Harness 1 WHITE RED PARKING LIGHT INPUT 2 WHITE PARKING LIGHT OUTPUT Locate the parking light output wire at the vehicle s light switch Verification This wire registers positive voltage when the parking lights are turned on Positive switching Parking Lights Connect the WHITE RED wire to a 15 Amp max fused battery source Connect the WHITE wire to the parking light output wire Negative switching Parking Lights Connect the WHITE RED wire to a good chassis ground Connect the WHITE wire to the parking light output wire 3 BL
17. able options for timing 2 ORANGE BLACK AUX 4 This wire provides a 200mA output capable of driving relays For Control of optional accessories i e Power Window Sunroof etc To activate refer to the transmitter button configuration chart Please refer to the selectable options for timing 3 GRAY BLACK AUX 3 This wire provides a 200mA output capable of driving relays For Control of optional accessories i e Power Window Sunroof etc To activate refer to the transmitter button configuration chart Please refer to the selectable options for timing 4 WHITE BLACK AUX 2 This wire provides a 200mA output capable of driving relays For Control of optional accessories i e Power Window Sunroof etc To activate refer to the transmitter button configuration chart Please refer to the selectable options for timing 2014 Voxx Electronics Corporation All rights reserved 5 3 Pin Lock Output Harness 1 BLUE UNLOCK 3 GREEN LOCK The door lock unlock outputs are designed to control several different types of systems which may require additional parts Please review the wire and location chart to see which type of door lock system is in your vehicle The most common types are shown in the following diagrams These wires supply a 500mA output Negative Switching Locks All Door Lock and Unlock Locate the lock unlock wire at the vehicle s lock unlock Switch Verification These wire
18. ctory horn 16mS 10mS 30mS 40mS 50mS 6 Real Panic Controls the horn output when the system is triggered ON Randomized horn honks when panic is triggered OFF Standard pattern horn honks when panic is triggered 7 AUX 1 Controls the VIOLET BLACK AUX 1 output activation type and timing 1 Second Pulse Single 1 second pulse Latched Output stays active until button is pressed again Latched until IGN ON Output stays active until the ignition is turned on Dome Light Output Output used for illuminated entry and is not controlled by the AUX 1 function of the transmitter Defrost Output Single Pulse Single 1 second pulse after start Defrost Output Latched 5 Minutes 5 minute continuous output after remote start 2014 Voxx Electronics Corporation All rights reserved 29 8 AUX 2 Controls the WHITE BLACK AUX 2 output activation type and timing 1 Second Pulse Single 1 second pulse Latched Output stays active until button is pressed again Latched until IGN ON Output stays active until the ignition is turned on 10 Second Pulse with Arm Output stays active for 10 seconds with press of lock button 10 Second Pulse with Disarm Output stays active for 10 seconds with press of unlock button 9 AUX 3 Controls the GRAY BLACK AUX 3 output activation type and timing 1 Second Pulse Single 1 second pulse Latched Output stays active until button is pressed again Latched until IGN ON Output stays activ
19. d the valet override button then start the vehicle using the key 5 When the unit senses the tach signal the parking lights will begin to flash Allow the vehicle to settle to a normal idle speed 7 Release the valet program push button switch The parking lights will turn on for 2 seconds and 1 long chip will indicate that the learned tach signal is stored and the unit has exited tach learn mode Je Qo d cx NOTE If the unit fails to learn tach rate due to an improper tach connection or a poor tach source the parking lights will not flash To correct this situation locate and connect the PURPLE WHITE wire to the proper tach signal and then repeat the tach learn routine Smart Tachless Mode Smart Tachless Mode is available only if a tach signal has never been learned to the System and when activated will automatically change the Tach Mode feature in option programming to Tachless without the need to enter the feature programming mode 1 Activate the remote start The parking lights should begin flashing 7 times indicating no tach signal has been learned 2 Within the 7 flash time period press and hold the OX button 3 The system will chirp 1 time indicating the system is now in tachless mode 2014 Voxx Electronics Corporation All rights reserved 25 2 Adjusting the Shock Sensor 1 Increase sensitivity by turning the adjustment dial clockwise 2 Decrease sensitivity by turning the adjustment dial counter clockw
20. e ON OFF OFF Standard security system operation ON Enables Car Jack mode functionality as described in the owners manual 2014 Voxx Electronics Corporation All rights reserved 27 8 Ground While Armed Orange Output Controls the output of the orange wire This wire will either supply a output when armed OR disarmed 9 DBI Port Protocol Determines the protocol type in which the DBI port uses to interface with external modules DBI Protocol ADS Protocol 10 Arm Disarm Chirp Parking Light Pattern Determines the number of chirps and parking light flashes when the system is armed disarmed Standard 2 chirps light flashes with arm 1 chirp light flash with disarm Inverted 1 chirp light flash with arm 2 chirps light flashes with disarm Feature Bank 3 Output Control 28 1 Extended Lock Pulse Controls the timing of the BLUE and GREEN lock output wires 1 Second Single 1 second lock pulse single 1 second unlock pulse 3 5 Seconds Single 3 5 second lock pulse single 3 5 second unlock pulse 1 Second Lock Double Pulse Unlock Single 1 second lock pulse double 1 second unlock pulse 30 Second Lock Double Pulse Unlock Single 30 second lock pulse double 1 second unlock pulse Double Pulse Lock 1 Second Unlock Double 1 second lock pulse single 1 second unlock pulse 2 Factory Disarm Controls the timing of the LT GREEN BLACK factory disarm wire on the 6 pin output harness only
21. e Light Delay Theater Dimming esee 26 ca6554 Install revA Feature Description S wo 27 Transmitter Button Functions 35 Security Trigger Zones uan 37 Remote Start Shutdown Diagnostics eese 37 System Layout deed ee 38 2014 Voxx Electronics Corporation All rights reserved BEFORE YOU BEGIN FOR AUTOMATIC TRANSMISSION VEHICLES ONLY PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions JE Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces Avoid mounting components or routing wires near CM E E c moving parts We BE Tape or loom wires under hood for protection and appearance Use grommets when routing wires through metal surfaces Use a Digital Multi Meter for testing and verifying circuits DO NOT USE A TEST LIGHT D COMPUTER SAFE PROBE as these can set off air bags or damage vehicle computers Technical Support 800 421 3209 a TI http avxtech1 com 4 ca6554 Install revA 4 Pin Main Harness z lt z 6 Pin Start Harness 6 PIN START 6 Pin Output Harness BROWN BLACK HORN OUTPUT BLUE BLACK START STATUS ACTIVE OUTPUT VIOLET BLACK AUX 1 OUTPUT RED WHITE TRUNK RELEASE OUTPUT LT GREEN BLACK FAC
22. e until the ignition is turned on 10 Second Pulse with Arm Output stays active for 10 seconds with press of lock button 10 Second Pulse with Disarm Output stays active for 10 seconds with press of unlock button 10 AUX 4 Controls the ORANGE BLACK AUX 4 output activation type and timing 1 Second Pulse Single 1 second pulse Latched Output stays active until button is pressed again Latched until IGN ON Output stays active until the ignition is turned on 10 Second Pulse with Arm Output stays active for 10 seconds with press of lock button 10 Second Pulse with Disarm Output stays active for 10 seconds with press of unlock button 11 AUX 5 Controls the PINK BLACK AUX 5 output activation type and timing 1 Second Pulse Single 1 second pulse Latched Output stays active until button is pressed again Latched until IGN ON Output stays active until the ignition is turned on 10 Second Pulse with Arm Output stays active for 10 seconds with press of lock button 10 Second Pulse with Disarm Output stays active for 10 seconds with press of unlock button ca6554 Install revA Feature Bank 4 Remote Start Control 1 RF Start Chirp Turns remote start activation confirmation chirps ON or OFF 2 Run Time Controls the time in minutes that the vehicle will stay running under control of the remote start until the system times out The system may also be shut down at any time by use of the transmitter or sys
23. ed the remote start will activate and run for the programmed time and shut down every 2 or 3 hours 12 Turbo Timer When activated the vehicle will run for the programmed time OFF 1 Minute 3 Minutes 5 Minutes 13 Transmission Mode Select the type of remote start activation based on the vehicle s transmission type Automatic For use with automatic transmission vehicles Standard remote start operation Manual For use with manual transmission vehicles Remote start ready mode must be set upon exit of vehicle to enable remote start 14 Temperature Start Sets the threshold temperature for temperature start mode When temperature start is activated the remote start function will activate when the ambient temperature drops below the selected temperature ca6554 Install revA 15 Accessory Output Programmable high current output Accessory Output becomes active with the same timing as the accessory output drops out during crank Ignition Output becomes active with the same timing as the ignition output and does not drop out during crank Start Crank Output becomes active with the same timing as the starter output wire during crank only 16 Pulse Additional Outputs w Unlock When the Unlock button is pressed on the remote transmitter the system will also simultaneously pulse additional outputs Ignition Accessory amp Ground While Running outputs for 1 second The 3rd setting also activates the pulse after
24. he unlock position in the driver s door cylinder This output can be configured in option programming 2 LT BLUE FACTORY ARM PULSE AFTER START This wire will supply a 200mA pulse both upon arming the system and upon successful completion of the remote start activation sequence and is typically used to re lock the vehicle s doors upon remote start if necessary This output can be configured in option programming 3 GREEN WHITE PULSE AFTER SHUTDOWN This wire will supply a 200mA pulse after the remote start shuts down This is typically used to re lock the vehicle s doors if they unlock upon remote start shutdown It can also be used to pulse a door pin switch wire to prevent the vehicle s accessories from remaining on after remote start shutdown This output can be configured in option programming 4 BLACK YELLOW PULSE DURING CRANK Locate the vehicle s second starter crank wire at the ignition switch if equipped Verification This wire registers voltage only in the start crank position of the ignition switch This wire will supply a 200mA output and can be configured in option programming ca6554 Install revA 4 Pin AUX Output Harness 1 PINK BLACK AUX 5 This wire provides a 200mA output capable of driving relays For Control of optional accessories i e Power Window Sunroof etc To activate refer to the transmitter button configuration chart Please refer to the select
25. ise Testing the Shock Sensor Arm the system and wait 6 seconds for the zone to stabilize then firmly strike the vehicles bumper Chirp Delete User Accessible System ARM DISARM chirps can be toggled ON or OFF without entering the programming feature banks 1 Turn the ignition ON then OFF 2 Press and release the valet programming button 3 times The system will respond with 1 chirp for ON or 2 chirps for OFF Dome Light Delay Theater Dimming The system can be programed to delay arming after the lock button is pressed 60 second max for vehicles with a dome light delay or theater dimming feature Once programed the system will learn the timing of the dome light delay and add 2 seconds before arming 1 Close all doors with ignition off 2 Usingthe transmitter press LOCK UNLOCK LOCK UNLOCK LOCK UNLOCK LOCK The LED will light solid to indicate the system has entered DOME DELAY LEARN MODE 3 Immediately OPEN then CLOSE the door WITHOUT disarming the System The system will then monitor the door trigger wire Once the dome light turns off the system will then add 2 seconds and then exit the learning mode 4 The LED will begin to flash indicating the system has exited the learning mode and is now armed ca6554 Install revA Feature Descriptions Feature Bank 2 Security 1 Silent Choice Controls the normal arm disarm chirps of the security system ON Silent arming disarming upon firs
26. lock before Unlock Before Lock After Lock After 17 Start OFF Start Lock Start Start SM Blue amp Green Lock Output Wires After Start Feature Bank 5 7 Chirps 4 Pin Alternate Output Control 1LEDFlash 2LEDFlash 3LEDFlash 4LED Flash 5LED Flash 6 LED Flash Pulse Before T 1 Lt Green Black Output E lei less Pe Running Crank Unlock Pulse After 2 Lt Blue Output Start During Ground While Ignition Accessory Pulse During Running Crank Lock Pulse After Ground While TN Pulse During 3 Green White Output A Running Ignition Accessory lest Pulse During Ground While di 4 Yellow Output Crank Running Ignition Accessory ca6554 Install revA Tach Programming The unit will not operate unless tach is programmed or tachless option is turned ON If an attempt is made to start the vehicle via the remote start without first programming tach the unit will flash the parking lights 7 times indicating tach has not been learned and stored If the tach rate is not properly programmed to the specific vehicle the unit may not realize that the vehicle is running in certain instances and re engage the starter motor The Remote Start unit will learn the tach rate of most vehicle s single coil multiple coil packs or single injector To learn tach Turn the ignition key to the ON position Press and release the valet override button 3 times Immediately turn the ignition key OFF Press and hol
27. nd Release Lock then Shock Bypass x Press Lock Car Find Hidden Alarm x x Press and Release Car Find then Press Lock ing x x Press and Release Bypass Turbo Timer x x Press Unlock Start Ignition ON OFF Press and Hold gus Hour Stay x Valet Button Press Start 4 times Daily Start Timer x x Press Lock Start Temperature X x Press Unlock Start While Armed Start AUX 2 3 4 5 Access in AUX Mode Press and Hold Find Start Enter AUX Mode x x Transmitter LED flashes 1 time AUX 2 Push and Hold 3 Sec AUX 3 x Push and Hold 3 Sec AUX 4 Push and Hold 3 Sec AUX 5 x Push and Hold 3 Sec 2014 Voxx Electronics Corporation All rights reserved 36 2 Way Lock Unlock Find d Start Function Operation Method Transmitter Panic Lock x Press and Release Unlock x Press and Release 2 Step Unlock x Press and Release 2 times Trunk Push and Hold 3 Sec Car Finder x Press and Release Panic x Push and Hold 3 Sec Press and Release 1 or 2 times Ramos star depending on selectable option Remote Start Shutdown Push and Hold 3 Sec Run Time Extention Press and Release 4 times AUX 1 x Xx Push and Hold 3 Sec Press and Release Lock then SHEE SEATED M Press Lock Find Hidden Alarm x x Press and Release Car Find then Press Lock Rasslye ing x x Press and Release Bypass Turbo Timer x Press Unlock Start Ignition ON
28. rior light is on This wire will register positive voltage when the door is closed and the interior light is off Connect the GREEN wire to the vehicle s negative door input wire s NOTE Certain vehicles may require multiple connections Refer to vehicle application guide 2014 Voxx Electronics Corporation All rights reserved N 3 PURPLE DOOR TRIGGER INPUT Locate the vehicle s dome light or door pin switch wire Verification This wire will register positive voltage POS when the door is opened and the interior light is on This wire will register ground or 0 Volts when the door is closed and the interior light is off Connect the PURPLE wire to the vehicle s positive door input wire s NOTE Certain vehicles may require multiple connections Refer to vehicle application guide 4 WHITE BLUE EXTERNAL START INPUT This wire will activate the Remote Start function when a GROUND pulse is applied to it an external device 5 GRAY HOOD PIN INPUT Install a Hood Pin Switch and connect to the GRAY wire This connection is required for Remote Start Verification This wire when connected will register ground when the vehicle s hood is opened Connect the GRAY wire to the hood pin NOTE Be sure to loom the wire and seal the grommet 6 GRAY RED PARKING BRAKE INPUT Locate the vehicle s parking brake wire Verification This wire will register ground when the vehicle s PARKING B
29. s will register ground when the Lock and Unlock Switches are activated Connect the GREEN and BLUE wires shown in the diagram below Negative Locks GREEN Lock Output Vehicle Door Lock Control Relays BLUE Unlock Output 16 ca6554 Install revA Positive Switching Locks All Door Lock and Unlock Locate the lock unlock wire at the vehicle s lock unlock switch Verification These wires will register positive voltage when the Lock and Unlock switches are activated Connect the GREEN and BLUE wires shown in the diagram below Positive Locks Fused 12 Volt Battery Souce GREEN Lock Output Vehicle Door Lock Fused 12 Volt e Relays Battery Souce BLUE Unlock Output Reverse Polarity Locks 5 Wire Door locks All Door Lock and Unlock Locate the lock unlock wire at the vehicle s lock unlock Switch Verification These wires will rest at ground and register positive voltage when the Lock and Unlock switches are activated Connect the GREEN and BLUE or BLUE GREEN wires shown in the diagram below using 2 SPDT relays not supplied Reverse Polarity Locks Fused 12 Volt Battery Souce GREEN Lock Output To Door Lock Motor Fused 12 Volt Battery Souce BLUE Unlock Output
30. sam qo AUX4 1Second tehed Latched until 10 Second Orange Black Output Pulse IGN ON Pulse with Arm Disarm 11 5 1Second Latched until 105 10 Second Pink Black Output Pulse s IGN ON Pulse with Am 59 2014 Voxx Electronics Corporation All rights reserved 23 24 Feature Bank 4 6 Chips 1LEDFlash 2LEDFlash 3LED Flash 4LED Flash 5LED Flash 6 LED Flash Remote Start Control 1 RF Start Chirp ON OFF 2 Run Time 15 Minutes 5 Minutes 10 Minutes 20 Minutes 45 Minutes 60 Minutes 3 Running Lights Steady Flashing Tachless Hybrid Crank 4 Tach Mode Tach Crank Average Average DBI Port Voltage Voltage 5 Voltage Level High Low 6 Crank Time 1 0 Seconds 0 8 Seconds 1 5Seconds 2 0 Seconds 4 0 Seconds 7 Crank Averaging Crank Time Averaging Preset Time Gas Diesel Gas 10 Second 15 Second 20 Second 45 Second Delay Delay Delay Delay 9 Single Double Press Start Double Press Single Press Ignition 2 Output PM 10 Pink White Ignition Accessory Start Crank 11 2 or 3 Hour Start 3 Hour 2 Hour 12 Turbo Timer OFF 1 Minute 3 Minute 5 Minute 13 Transmission Mode Automatic Manual 14 Temperature Start OFF 14F SF 4F ig peer Accessory ignition Start Crank Orange Pulse Additional Outputs when IGN ACCY IGN ACCY 16 Unlock is Pressed nid GWR GWR Pulse After Shutdown Door Lock Control During Remote Un
31. second pulse when unlock is pressed Ground While Running Continuous output for the entire remote start sequence until after the vehicle shuts down Ignition Output becomes active with the same timing as the ignition output and does not drop out during crank Accessory Output becomes active with the same timing as the accessory output drops out during crank Pulse During Crank Output becomes active with the same timing as the starter output wire during crank only 2 Lt Blue Output Controls the LT BLUE output activation type and timing Pulse After Start During Lock 1 second pulse after the remote start sequence and has confirmed the vehicle is running Also a 1 second pulse when lock is pressed Ground While Running Continuous output for the entire remote start sequence until after the vehicle shuts down Ignition Output becomes active with the same timing as the ignition output and does not drop out during crank Accessory Output becomes active with the same timing as the accessory output drops out during crank Pulse During Crank Output becomes active with the same timing as the starter output wire during crank only 3 Green White Output Controls the GREEN WHITE output activation type and timing Pulse After Shutdown 2 second pulse after the remote start has shutdown Ground While Running Continuous output for the entire remote start sequence until after the vehicle shuts down Ignition Outp
32. shutdown output to turn off the RAP on certain vehicles OFF When Unlock is pressed no additional outputs are activated IGN ACCY GWR When the Unlock button is pressed the system will also simultaneously pulse the Ignition Accessory amp Ground while Running outputs for 1 second IGN ACCY GWR then Pulse After Shutdown When the Unlock button is pressed the system will also simultaneously pulse the Ignition Accessory amp Ground while Running outputs for 1 second then waits 2 seconds then pulses the green white pulse after shutdown wire for 1 second 17 Door Lock Control During Remote Start Controls the systems door lock outputs during the remote start sequence OFF The system will not lock or unlock the vehicle Unlock before Start Lock After Start Unlock Pulse before remote start sequence begins Lock pulse after remote start sequence is complete and engine is running Unlock Before Start Unlock Pulse before remote start sequence begins Lock After Start Lock pulse after remote start sequence is complete and engine is running Lock After Shutdown Lock pulse after remote start shutdown sequence is complete 2014 Voxx Electronics Corporation All rights reserved 33 Feature Bank 5 4 Pin Alternate Output Control 34 1 Lt Green Black Output Controls the LT GREEN BLACK output activation type and timing Pulse before Start During Unlock 1 second pulse when remote start is activated Also a 1
33. stalled in a second vehicle Manual Feature Programming Feature Bank 2 5 Turn the ignition ON Press and hold the valet override button Within 10 seconds the system will chirp 3 three times Aoc Use the valet override button to advance through each option bank For feature programming advance to Feature Bank 2 3 4 or 5 whichis 4 four 5 five 6 six and 7 seven chirps 5 Use the transmitter Q button to scroll through the selections in each feature bank the system will chirp to match the feature number 6 Press the transmitter B button to change the desired feature The LED will flash indicating the changed feature 2014 Voxx Electronics Corporation All rights reserved 21 22 Defaulting All Features Pressing the button anytime while in any of the feature banks will default all features and return you to feature bank 2 4 chirps NOTE The system will remain in feature programming mode as long as the ignition is on there is no time limit To exit programming turn the IGNITION OFF Feature Bank 1 3 Chirps Transmitter Programming Refer to transmitter programming scan cano fenis 1LEDFlash 2LEDFlash 3LEDFlash 4LED Flash 5LEDFlash 6 LED Flash 1 Silent Choice ON OFF 2 Passive Locks Active Passive 3 Passive Arming Active Passive 4 Siren Horn Arm Disarm Chirps Siren Horn Siren Horn 5 Siren Duration 30 Seconds 60
34. t press of lock unlock pressing lock unlock a second time will activate the arm disarm chirps respectively The system will only sound the arm disarm chirps upon a second press of the lock unlock buttons OFF normal arm disarm chirps upon the first press of lock unlock 2 Passive Locks Determines manual or automatic locking of the vehicle s doors Active Requires use of the transmitter to lock the vehicle s doors Passive Automatically locks the vehicle s doors 1 minute after the last door is closed Note For Passive Locks feature 3 Passive Arming must also be set to passive 3 Passive Arming Determines manual or automatic locking of the vehicle s doors Active Requires use of the transmitter to arm the security system Passive Automatically arms the security system 1 minute after the last door is closed 4 Siren Horn This feature selects which output s will sound the system s arm disarm chirps This feature does not effect the triggered state of the security System and during a triggered cycle both the siren and horn outputs will activate respectively 5 Siren Duration This feature controls the length of time the system will sound when triggered 6 Security Controls security functionality ON OFF ON Full security functionality OFF The security system does not trigger Panic Remote Start and all other convenience features operate as normal 7 Anti Hijack Mode Controls car jack mod
35. tem shutdowns 3 Running Lights Controls the WHITE parking light output wire during remote start Steady Parking lights constant during the remote start cycle Flashing Parking lights flash at a slow pace during the remote start cycle 4 Tach Mode Determines how the system monitors the engine running during remote start Tach Hard wired directly to the tach wire of the vehicle to monitor AC voltage Tachless Crank Average Voltage Determines crank time by averaging the last 8 times the vehicle was started with the key and then monitors the change in voltage after remote start Hybrid Crank Average No Voltage Determines crank time by averaging the last 8 times the vehicle was started with the key DBI Port Monitors the vehicle s tach rate through an interface module connected to the DBI port 5 Voltage Level The voltage variance for remote start when set to tachless see tach mode HIGH The variance in battery voltage from before the remote start is activated to after the engine is running must be greater than 0 5 volts LOW The variance in battery voltage from before the remote start is activated to after the engine is running may be less than 0 5 volts 6 Crank Time Preset output times for the PURPLE starter wire 7 Crank Average Crank Time The length of time in which the remote start will crank the vehicle s starter Crank Average Determines crank time by averaging the last 8 times
36. ut becomes active with the same timing as the ignition output and does not drop out during crank Accessory Output becomes active with the same timing as the accessory output drops out during crank Pulse During Crank Output becomes active with the same timing as the starter output wire during crank only ca6554 Install revA 4 Black Yellow Output Controls the BLACK YELLOW output activation type and timing Pulse During Crank Output becomes active with the same timing as the starter output wire during crank only Ground While Running Continuous output for the entire remote start sequence until after the vehicle shuts down Ignition Output becomes active with the same timing as the ignition output and does not drop out during crank Accessory Output becomes active with the same timing as the accessory output drops out during crank Transmitter Button Functions NY Lock Unlock Gar Start Operation Method Transmitter Panic Lock x Press and Release Unlock x Press and Release 2 Step Unlock x Press and Release 2 times Trunk x Push and Hold 3 Sec Finder x Press and Release Panic Push and Hold 3 Sec Press and Release 1 or 2 times ou SEs 5 depending on selectable option Remote Start Shutdown x Push and Hold 3 Sec Run Time i Extention x Press and Release 4 times AUX 1 x x Push and Hold 3 Sec Press a
Download Pdf Manuals
Related Search