Minelab Musketeer Colt Instruction manual
Contents
1. pops or clicks Non ferrous objects will give a normal signal beep and be accepted Page 14 The Minelab Musketeer Advantage Typical ferrous objects encountered by treasure hunters are nails screws washers bits of wire etc These objects are generally not considered to be of value so it is a distinct advantage to be able to ignore these objects while detecting in this setting Objects that will cause the Advantage to produce a signal beep will be non ferrous metals This includes such items as aluminum foil most jewellery pull tabs coins bottle tops gold silver brass etc Not all of these non ferrous objects are considered valuable Therefore by using the Discrimination Level Adjust the Advantage can be adjusted to ignore some of the less valuable non ferrous objects while still locating the more valuable targets By turning the Discimination Level Adjust control clockwise some non ferrous objects of increasing conductivity will be ignored The Advantage uses the electrical conductivity of the object to determine the type of metal detected and based upon the Discrimination Level Adjust setting will either ignore or accept the object The following diagram shows some common objects and where the Discriminate control has to be set to ignore them Low Conductivity High Conductivity small iron bolts silver copper nails etc brass lead REJECTED ACCEPTED P0563 A Figure 10 Discrim2. METAL DETECTOR SUPERSTORE You always get more for your money at Kellyco Toll FREE 1 888 KELLYCO 1 888 535 5926 www kellycodetectors com Kellyco Metal Detector SuperStore 1085 Belle Ave Winter Springs Florida 32708 The Minelab Musketeer Advantage Instruction Manual Contents IOS se nto 1 OEE E TTT DR OF Parts E A AE A EE EEE A E E E TEE AT ACCESSOTICS vo rsi s a Ra ae ee Hae eee eTii Assembling Your Musketeer Advantage sss sese eee eee Batteries nerea ee EE TERTRE teu tee ates The Musketeer Advantage serene nispa aa aa a a 11 Controls 6 Te Te 11 Basic Operating Instructions sese sees eee eee eee 18 Practicing the Conttols s i o eeren receten araa arai iaa 19 Tr asur Hunting TIPS ieena ee ee inca heel ar TE aa 21 Environmental Concer Susianti orae e eie reii ER E 5 22 Detect r TTT 23 Trouble shooting Guide srei erete aE E aa 24 SPeCIHCAHONS reta e Nee teckel ira seed a eE E E oleate tah as 25 Warranty and e e Re Le e esdieevetcetressieuestt 26 Minelab Service Repair Form sva2Seareazrat caze VT eS ena e ae TH ET 27 4901 0038 1 2 Page 2 The Minelab Musketeer Advantage WARNING THIS DOCUMENT CONTAINS MINELAB ELECTRONICS PTY LTD RIGHTS TECHNICAL DATA OR RESTRICTED RIGHTS DATA OR BOTH Minelab Electronics Pty Ltd This work is copyright Apart from any use as permitted under the Copyright Act 1968 no part may be reproduced by any process without written permission from Minelab Electronics Pty Ltd
3. away from known electrical devices or metal objects and support the Musketeer so that objects can be easily moved past the coil Then a Ensure the Mode Switch is in Discriminate b Turn the Discriminate control to approx 1 position Fig 10 page 14 c Turn the Sensitivity Control to maximum If excessive interference is encountered turn the Sensitivity control counter clockwise until you are comfortable with its stability d One at a time pass the test objects across the coil The Advantage should beep on the non ferrous ones but not on most ferrous objects Large ferrous objects may produce short pops clicks or even beeps To reject these items you may need to turn the Level Adjust knob further in a clockwise direction e Now turn the Level Adjust control progressively clockwise in steps and pass the objects over the coil and see when certain objects are rejected By experimenting with different settings of the Level Adjust control you will see where to set the Advantage to accept or reject the targets you wish to hunt for Now for some treasure hunting Take the Advantage to the site you wish to hunt Then f Place the coil flat on the ground and flick the Mode Switch to Discriminate g Turn your Level Adjust knob to your preferred setting Remember this is a trash to treasure ratio so select it based on how much trash you are willing to dig to find your first good item You
4. By Pinpointing accurately you are AUUE sure to save time and can remove the target with minimal Gr a d Adjust disturbance to the environment of the area Enable Pinpoint is not normally used while searching Its purpose P0561 A d ae i is to locate the precise position of the target after it has been discovered in one of the search modes The Pinpoint feature works only while the Advantage is in the All Metals mode While in the All Metals Pinpoint mode the Advantage is a non motion detector This means that the coil does not have to be moving to detect a target Sometimes when in this mode the Audio volume may become loud and erratic If this occurs you will need to retune by pressing and releasing the Threshold Reset function If this does not solve the problem you may then need to check the Ground Balance as described on page 12 or reduce the Sensitivity of the detector slightly Threshold Reset Threshold Reset is located at the centre of the control panel The switch is spring loaded and will flip back into its normal position when you release it This control is only operational while the Advantage is in the All Metals mode and used in conjunction with the Pinpoint mode as described below to assist in accurate target location Page 16 The Minelab Musketeer Advantage When the approximate location of the target has been determined in the Discriminate mode switch to the All Metals Pin
5. experienced operator you should practice maintaining a constant coil height at the extremity of each swing maintaining contact with the ground will make this easier This is important as variation in coil height at the end of each swing can cause confusing sounds and will reduce detection depth P0188 A Figure 12 Sweeping the Coil NOTE Each sweep of the coil should overlap the previous one by 25 This will ensure good ground coverage Keeping the coil in contact with the ground will increase detection depth and response to small objects Page 22 The Minelab Musketeer Advantage Environmental Concerns Firstly it should be pointed out that treasure hunting with a metal detector is the most environmentally friendly way to recover coins rings and other treasure items However it is important to leave an area that you have searched in the same condition as you found it All holes that have been dug must be properly refilled Not only is it environmentally unacceptable to not fill in your holes it is also very dangerous There are special tools to enable you to recover targets easily from grassed areas without digging large holes talk to your detector shop or club for the preferred method of digging up your target Take away and properly dispose of any junk that you find or produce such as nails tin cans or flat batteries Leaving an area scarred can result in action be
6. 118 Hayward Avenue Torrensville SA 5031 Australia Instruction Manual Page 3 Introduction Congratulations on purchasing the Musketeer Advantage This metal detector has been designed for general purpose treasure hunting and the main features include lightweight construction sharp target response simplified controls for easy operation and substantial depth capabilities Your Advantage detector is designed to locate valuable metal objects in high trash areas These conditions are commonly encountered by treasure hunters in places that have been inhabited for long periods or by armies using the areas as camping grounds or battlefields The Advantage detector has been designed to serve the needs of both the speed hunter and the slow motion hunter Units may be moved at a rapid hunt pace or at a much more leisurely pace while enjoying the sharp target response in either mode without sacrificing depth capabilities You will be surprised at how well the depth capabilities of the Advantage will challenge units currently on the market 43 The operating frequency of your Advantage has been set at 5 kHz This frequency has been chosen for its high level of sensitivity to large ferrous targets as well as coins jewellery and other valuable non ferrous objects while still being able to accurately discriminate against trash With the Advantage detector Minelab has set out to provide you with a high performance easily opera
7. 1190 mm Control Box excl Batteries 530 g TS800 Slimline Coil 500 g TS1000 Slimline Coil 650g Alkaline Cells Eight 1 5V AA NiMH Battery Pack 12V 1000 mAhr TS800 Slimline Double D waterproof TS1000 Slimline Double D waterproof Impedance 8 32 ohms Jack Stereo Mono 14 Transmission sinewave 5 kHz Fixed Manual Ground Adjust Pot 1 turn Discriminate All Metals Ground Adjust Enable All Metals Pinpoint On Off Sensitivity Ground Adjust Discriminate Level Adjust All Metals Discriminate Pot and switch Pot and switch Pot 1 turn Switch 2 Pos Pinpoint Switch 3 Pos Control Box 2 years Coil 1 year AUS 595835 others pending
8. 7 Shaft Mount a Position the control box so that the recess in the control box 11 is aligned with the leading edge of the mounting clip 12 Push the foward section of the control box upwards until the trigger clicks indicating the control box is secured 10 P0543 A b Firmly wind between 17 and 20 turns of the cable around the shaft until it reaches Figure 4 Mounting the the control box control box NOTE Leave enough slack at the bottom of the cable near the coil to adjust the coil position without straining the coil cable c Connect the cable connector 10 to the plug on the rear of the control box d Use Velcro tabs to secure cable in the correct position on the shaft maintaining slack at coil and control box Hipmount Hipmounting is an alternative to mounting the detector on the shaft and it significantly reduces the strain on your arm enabling you to search for longer periods of time without undue fatigue To hipmount the detector you will be required to purchase the hipmount bag from your dealer a Check that there are charged batteries in the control box 11 b Put the control box into the hipmount bag 13 as shown in Fig 5 c Place the hipmount bag in your preferred working configuration The hipmount bag can be worn on the belt or over the shoulder d Wind about 5 turns of the cable around the P0544 A shaft This will reduce the amount of Figure 5 Control box in exc
9. can always turn it up or down during use Page 20 The Minelab Musketeer Advantage h Now turn the Sensitivity control to maximum If excessive interference is encountered turn the Sensitivity control counter clockwise until you are comfortable with its stability Remember it is suggested that you hunt with sensitivity as high as possible without instability annoying you This control can be altered during hunting if you encounter more random signals in one area than another 1 Lift the search coil approximately 2 1 inch 1 2 5 cm from the ground enough to take the weight off the coil Now swing the search coil from side to side keeping the coil level and parallel to the ground surface throughout the swing Fig 12 page 21 jp Listen to the reaction to each target you find noting the depth and condition of the ground as you recover it Carry a small notepad to take notes and review these notes at some later time to improve your knowledge of how your Advantage performs As you become more experienced in using the Advantage you will notice that your trash ratio will drop even though you may not be increasing the discrimination level This is because you have become more attuned to the target signals and know how the Advantage responds Instruction Manual Page 21 Treasure Hunting Tips Your Musketeer Advantage detector will perform at its best when the coil is kept in contact with the ground If you are not yet an
10. e charger into the socket on the rechargeable battery pack b Plug the charger into the power source and switch on c Ared light will appear on the charger indicating that it has power car charger only d A green light will appear on the battery pack during charging e Acompletely flat battery pack will take approximately 12 14 hours to fully charge f The green light on the battery pack will fade dim once it is fully charged g A fully charged NiMH pack will give between 15 and 20 hours detecting time depending on the number of targets found 12V CAR MAINS aana CHARGER P0547 A Figure 8 Car amp mains battery chargers Instruction Manual Page 11 The Musketeer Advantage Controls amp Functions This section gives detailed descriptions of the controls of the Musketeer Advantage and their function Having knowledge of these controls means that you will be able to achieve the best performance possible with your detector As you gain experience with your detector it may be useful to refer back to this section Threshold Reset E Pinpoint off D D Ground Adjust E Sensitivity able es All Metals Fix lt J Y a Ground Adjust Discriminate Level Adjust P0556 A Figure 9 The Musketeer Advantage control panel Sensitivity Control and On Off Switch This knob is located in the middle left hand side of the control box and allows the unit to be turned on and off as well as c
11. ess cable hipmount bag Page R The Minelab Musketeer Advantage NOTE Leave enough slack at the bottom of the cable near the coil to adjust the coil position without straining the coil cable e Use Velcro tabs to secure the cable in position at the base of the shaft and where the cable leaves the shaft f Connect the cable connector to the rear of the control box Batteries Your Musketeer Advantage is supplied with a 12 volt battery pack to hold 8 AA alkaline batteries If you have not already done so you can purchase a rechargeable 12 volt NiMH battery pack a mains charger and a car charger from your authorised Minelab dealer Installation of Alkaline Batteries Ensure the detector is switched Off before opening the battery compartment a Remove battery pack from control box pulling back both release tabs on the battery pack housing BATTERY ORIENTATION b Slide open the lid on the battery pack c Place 8 AA alkaline batteries 14 into the base of the alkaline pack 15 Ensure they are aligned as shown in Fig 6 and as indicated inside the compartment d Slide the lid closed e Place the base of the battery pack at the rear of the battery compartment A Push the front edge of the battery pack firmly into position B The two battery clips will click into position to securely hold your Figure 6 Alkaline battery pack in place Fig 7 battery installation CAUTION High qual
12. hones used should be of a low impedence The socket will accept most stereo headphones with a 1 4 jack If the headphones have a Stereo Mono switch set it to Stereo Page 18 The Minelab Musketeer Advantage Basic Operating Instructions a Discriminate Mode e Install charged batteries s Set the All Metals Discriminate mode switch to the Discriminate position e Set central toggle switch to Ground Adjust Enable e Turn the Advantage On by turning the Sensitivity control in a clockwise direction Turn this control clockwise to your preferred level e Select the level of discrimination you wish to have by setting the Level Adjust control You are now ready to hunt b All Metals Mode e Install charged batteries e Set the All Metals Discriminate mode switch to the All Metals position e Set central toggle switch to Ground Adjust Enable e Turn the Advantage On by turning the Sensitivity control in a clockwise direction Turn this control clockwise to your preferred level You are now ready to hunt Instruction Manual Page 19 Practicing the Controls We suggest you first take some time to become familiar with how your Advantage responds to various metal objects Gather a collection of different metal objects such as a rusted nail pull tab brass button aluminum foil and some different types of relics e g bullets buckles coins Take the unit outside
13. ination Level Adjust control examples As you can see from the diagram items such as gold rings cover a large area of the Discriminate control This is because fine rings are less conductive than heavier rings and the higher the purity or Carat K rating the higher the conductivity Therefore if you set the Level Adjust control to ignore pull tabs you will also ignore some fine rings and other jewellery Instruction Manual Page 15 The setting of the Discrimination Level Adjust is relative to the types of objects that you wish to hunt for and the amount of trash that you are prepared to detect If you do not want to dig old bottle caps but want to dig brass buttons or copper coins the Discrimination Level Adjust control is set higher approximately at number 7 in Figure 10 but most fine white gold rings foil and some yellow gold rings will also be ignored Once you have learned where certain trash items are eliminated and where valuable items are accepted you are then able to decide where to set the Discrimination Level Adjust control You should only use as much discrimination as is required to eliminate the common junk items you do not want while still accepting the valuable items you do Always remember that another person detecting behind you who is willing to dig a little more trash will find the items you have passed over Pinpoint Threshold Reset Pinpoint is the ability to locate exactly where in the ground your target is
14. ing taken to prevent the use of metal detectors which spoils this fascinating hobby for others as well as yourself Instruction Manual Page 23 Detector Care The Advantage is a high quality electronic instrument finely engineered and packaged in a durable housing Taking proper care of it is mostly common sense e Do not leave batteries in the control box when the detector is not in use for a period exceeding two weeks Damage caused by leaking batteries would be severe and would void the warranty e Batteries Flat or faulty batteries cause many detector problems Ensure that you use only quality alkaline batteries and that they are replaced when the warning signal indicated through the headphones or speaker is heard e If temperatures are very high do not leave the detector in direct sunlight for longer than necessary Covering it when not in use will help protect it Try to avoid leaving it in a closed trunk or in a car sitting in sunlight e While the control box has been designed to be water resistant it is not waterproof Avoid wetting it unnecessarily Use the hipmount bag to prevent water and dust ingress Never allow the box to come into contact with gasoline or other oil based liquids e Keep the unit clean and dry and avoid getting sand and grit into the shafts or the tightening nuts Do not use solvents to clean the detector Use a damp cloth with mild soap detergent e Cables Ensure the coil cable is in good condit
15. ion and not subject to undue stress Page 24 The Minelab Musketeer Advantage Trouble shooting Guide Fault Solution No Sound Erratic Noises No Target Response Ensure the unit is turned On Check battery orientation and battery connections Ensure battery pack is correctly fitted Check headphones and their connection Check battery charge and battery connections Ensure coil plug is tightened firmly Reduce the sensitivity by turning counter clockwise Switch out of Fix ground balance position Check and adjust the ground balance Check headphones and their connection and lead Check for sand or grit between coil cover and coil Ensure unit is turned On Check battery charge and battery connections Check coil connection Check headphones and their connection In the unfortunate circumstance that you need to return your detector to Minelab for service please fill out the Minelab Service Repair Form on page 27 and enclose it with the detector Please supply as much detail as possible about the fault as this will assist our service engineers to rectify the problem quickly and efficiently Instruction Manual Page 25 Specifications These specifications are subject to change without notice Length Weight Batteries Coil Options Headphones Frequency Ground Rejection Search Modes Controls Warranty Patents Not included Extended 53 1350 mm Unextended 47
16. ity alkaline batteries should be used instead of standard carbon batteries as they will power your Advantage longer The use of headphones will further extend battery life Instruction Manual Page 9 Installation of NiMH Battery Pack a Ensure your NiMH pack is fully charged b Place the base of the battery pack at the rear of the battery compartment A Push the front edge of the battery pack into position B The two battery clips will click into position to hold the battery pack in place Fig 7 NOTE The NiMH battery pack is factory sealed and does not open P0546 A Figure 7 Battery pack installation Low Battery Warning and NiMH Recharging When the batteries are reaching the point at which they will no longer operate the Advantage will emit a distinct sharp pip from the speaker approximately every 30 seconds When this tone is heard it is recommended that the NiMH battery pack be recharged or alkaline batteries be replaced as soon as possible to avoid missing any targets The NiMH battery pack can be recharged using either a mains powered charger or a 12V charger that can be plugged into the cigarette lighter of your vehicle These accessories are available from your authorised Minelab dealer CAUTION Check the mains charger voltage Only use the appropriate mains charger for the country you are in Page 10 The Minelab Musketeer Advantage Using Your NiMH Chargers a Plug th
17. justed in either Discriminate mode or All Metals mode when the control toggle switch is in Ground Adjust Enable position CAUTION You can not effectively ground balance the Advantage whilst in the Pinpoint position Turning the ground adjust control while in this position will cause the detector to become erratic To ground balance the Advantage raise and lower the search coil approximately 2 6 inches 10 150mm above the ground while listening for changes in sound Start by having the Ground Adjust Control in its most clockwise position Now slowly turn the Ground Adjustment counter clockwise while continuing to raise and lower the coil until the audio response from mineralization is eliminated In areas of extreme mineralization you may not be able to completely balance out the effects of the ground mineralization In this case set the Ground Adjust control to the position where the sound varies the least as the coil is raised and lowered and then reduce the level of sensitivity to compensate for the excess mineralization Instruction Manual Page 13 Discriminate All Metals Switch All Metals The Discriminate All metals mode switch is located in the lower centre of the control panel and is used to select D either Discriminate or All Metals Discriminate In Discriminate mode the Discriminate control is active Possoa and can be adjusted so that Advantage can accept
18. le in this detector type equipment may vary according to the model or country of issue Certain descriptions and illustrations may differ in this manual from the exact model that you have purchased In addition Minelab reserve the right to respond to ongoing technical progress by introducing changes in design equipment and technical features at any time Instruction Manual Page 5 Accessories To further enhance your Advantage and give you greater capacity and versatility the following items are available for you to purchase Part Description Part Number e TS800 Slimline Coil 2021 0045 e TS1000 Slimline Coil 2021 0046 e Rechargeable NiMH Battery Pack 0311 0019 e Mains NiMH Charger Region Specific e 12V NiMH Vehicle Battery Charger 0302 0038 e Control Box Hip Mount Bag 3001 0034 e RPG Headphones 4523 0018 e Blue Minelab Cap 5306 0013 e Blue Minelab Polo Shirt Blue Minelab Jacket Size Specific Ask dealer for correct part number Assembling Your Musketeer Advantage Please follow these simple instructions to assemble your new Musketeer Advantage Refer to the drawings to identify parts and how they are positioned If you have any difficulties please contact your dealer for further instructions Armrest Upper Shaft Assembly a Remove the black nylon bolt and wing nut 1 from the armrest 2 b With the cup of the armrest positioned up so that your arm rests in the cup and your hand comfortably gri
19. ontrolling the sensitivity This control is often On thought of in terms of a depth control and it is to a point Sensitivity but it can also be used to make the unit more stable if oss7 A interference caused by ground chemistry mineralization or electrical fields is experienced At its Maximum position the detector may be noisy depending on electrical interference and ground mineralization To get the best depth from your detector this control should be set as high as you feel comfortable If you can operate with some noise then you are likely to get more depth If you prefer your detector to run quietly then turn the Sensitivity down until it is just quiet It s your choice Page 12 The Minelab Musketeer Advantage Ground Adjust Control This control allows you to adjust the ground balance of e your Advantage in order to compensate for changes in the level of ground mineralization At its most counter Fix clockwise position this control switches into the Fix position When in this position the Advantage is a fixed ground balance detector and requires no ground control adjustment Ground Adjust PO0SSS A If while detecting in this setting the ground mineralization becomes high the Advantage will produce ground noise or false signals To reduce these noises it will be necessary to switch the detector out of the Fix position and manually adjust the ground balance Ground balance can be ad
20. or ignore certain metal objects as described in the Discriminate Control section In this hunt mode the coil must be moving over the ground to detect a target If you stop moving the coil when over the target the signal will disappear In All Metals mode the Discriminate control has no effect and your Advantage will respond in the same way to all types of metal The All Metals Ground Adjust Enable mode is useful when searching for ferrous targets All Metals mode allows pinpointing of targets in conjunction with the pinpoint switch Pinpointing is discussed under Pinpoint on page 15 of the manual It is recommended to search in Discriminate mode to achieve the best depth Discrimination Level Adjust The Discrimination Level Adjust is located at the bottom right of the control panel This control is used when in Discriminate mode to set the level of discriminate or ignore for unwanted metal targets Metal objects fall into two broad categories ferrous and non ferrous A magnet can be used to determine if an object is a ferrous or non ferrous metal ferrous metals will be rosea attracted to the magnet while non ferrous metals will not In Discriminate mode the Advantage will discriminate most ferrous objects and only provide a signal for a non ferrous object If the Level Adjust is set to 1 as shown in Fig 10 page 14 large ferrous objects may produce short
21. point position The Audio volume will be at its loudest when you are able to hold the coil stationary over the target area Press and release the switch up to Threshold Reset function Gently move the coil sideways until you find the position where the Audio is at its loudest Note Do not lift your coil up as you may lose the target completely Repeating this process will refine your search even further if required Mark a line on the ground going from the tip to the toe of the coil this is the most sensitive part of the coil The open design of the coil makes marking the ground very easy As shown in Figure 11 turn 90 degrees to the line and repeat the pinpointing procedure until you are directly above the target Mark another line on the ground as before Where the two lines cross you should find your target Target could be anywhere in this area ee Sweep direction Exact location of target GY gt Sweep coil at Imaginary line of 90 degrees to strongest signal previous sweep P0048 B Figure 11 Pinpointing the target with the Musketeer Advantage Sometimes the detector will produce its maximum volume for a broad area over a target This generally indicates that the target is near the surface or is quite large To successfully Pinpoint these targets you may need to lift the coil up off the ground to narrow the target response before going through the Pinpoint procedure You should then be able to move
22. ps the foam handgrip slide the armrest 2 onto the end of the T ROSPEA black upper shaft 3 Figure 1 Armrest c Push the nylon bolt 1 through the holes Assembly and tighten the wing nut by hand Page 6 The Minelab Musketeer Advantage Lower Shaft Assembly a Unscrew the wing nut and remove the bolt 7 that is through the lower fibreglass shaft 5 Ensure the washers do not fall out 6 b Remove the wing nut bolt 7 and washers from the coil 8 These are spare parts c With the teardrop washers in place push the lower shaft 5 into the bracket on the coil so that the holes line up NOTE Ensure that the stainless steel spring clip located near the top of the fibreglass shaft is pointing toward the rear of the coil d Push the black nylon bolt 7 through the holes in the bracket on the coil from the cable entry side then place the washer and wing nut on the other end of the bolt and tighten it by hand P0044 C Figure 2 The coil and lower shaft assembly Completing the Shaft Assembly a Slide the lower shaft assembly 5 into the upper shaft 3 Note that the black plastic locking nut 9 may need to be loosened to get the lower shaft assembly in place b Set the length of the shaft by locking the stainless steel spring clip into one of the holes provided then tighten the plastic locking ring by hand P0542 A Figure 3 Completing the shaft assembly Instruction Manual Page
23. ted lightweight detector which is available at a realistic price To be a successful treasure hunter you must completely understand your detector s features and operation research your intended hunt area and respect the environment while you are hunting We at Minelab are confident that the Advantage will provide you with hours of enjoyment for all types of hunting whether it is on the beach in the country or in a competition hunt If you have any questions or comments we would like to hear from you Please contact your local Authorised Minelab Dealer or write to us directly We wish you every success in your treasure hunting Page 4 The Minelab Musketeer Advantage List of Parts The box in which your Musketeer Advantage is shipped should contain the following items When you first receive your Musketeer Advantage please check that all of these items are in the box Part Description Part Number Advantage Control Box TS800 Slimline Coil 2021 0045 Or TS 1000 Slimline Coil 2021 0046 Two Piece Shaft Assembly 8012 0022 Black Armrest 8011 0002 Armrest Cover 8001 0013 Alkaline Battery Pack 0311 0021 Nylon Bolt 1 5 x 1 4 1 off 4001 0001 Nylon Bolt 2 x 1 4 2 off 4001 0003 Nylon Wing Nut 1 4 3 off 4002 0003 Teardrop Washer 4 off 4005 0006 Velcro Tape Felt 8507 0001 Velcro Tape Hook 8507 0002 Warranty Card 5303 0001 This Instruction Manual 4901 0038 Since there may be a range of options availab
24. the coil closer to the taget and further refine your search Instruction Manual Page 17 After you have pinpointed and retrieved the target the Sensitivity of the detector should be reset to normal by pressing and releasing the Threshold Reset switch Although it is possible to search for targets in the All Metals Pinpoint mode it is not recommended The Discriminate and All Metals Ground Adjust Enable modes are much better for searching This is because in the All Metals Pinpoint mode the circuitry of the Advantage helps maintain a silent threshold by automatically reducing the Sensitivity when mineralization or targets are present The detector will automatically restore its sensitivity after a period approx 15 20 seconds from its last target Alternatively the Threshold Reset switch can be activated to immediately restore the sensitivity of the detector It is for this reason that the All Metals Pinpoint mode is not recommended as a search mode Audio Output The audio output of the Advantage is available through either an inbuilt loudspeaker or via a 1 4 stereo headphone jack When the headphones are plugged in the loudspeaker is disconnected Headphones are recommended for serious treasure hunting as they are more sensitive to slight target signals than the loudspeaker and shield your ears from external noises which can be distracting The use of headphones will also increase battery life P0562 A Headp
Download Pdf Manuals
Related Search